From: Michal Simek <monstr@monstr.eu>
To: u-boot@lists.denx.de
Subject: [U-Boot] [GIT PULL] Zynq changes
Date: Tue, 28 Jul 2015 15:43:16 +0200 [thread overview]
Message-ID: <55B786F4.3000000@monstr.eu> (raw)
In-Reply-To: <55B78681.9010604@xilinx.com>
Adding actual Tom's address.
Cheers,
Michal
On 07/28/2015 03:41 PM, Michal Simek wrote:
> Hi Tom,
>
> please pull these changes to your tree. The most of that changes are DT
> related which is simple synchronization DTSes with the kernel where
> binding was properly reviewed.
>
> Thanks,
> Michal
>
> The following changes since commit 26473945ad6667183296e7edee2a65edf31bb6f7:
>
> Merge branch 'master' of http://git.denx.de/u-boot-sunxi (2015-07-25
> 09:04:18 -0400)
>
> are available in the git repository at:
>
> git://www.denx.de/git/u-boot-microblaze.git zynq
>
> for you to fetch changes up to 711e5e26b41457e658155e7c225c9ccfed0182ef:
>
> cmd_mp: Add support for showing all CPU status by one command
> (2015-07-28 11:56:29 +0200)
>
> ----------------------------------------------------------------
> Michal Simek (29):
> zynq: gem: Setting up WRAP bit for one TX bd
> zynqmp: mp: Simplify set_r5_start handling
> zynqmp: Add support for IP detection via SLCR
> ARM: zynq: DT: Use the right names for nodes
> ARM: zynq: DT: Add missing nodes to DTSI
> ARM: zynq: DT: Add a fixed regulator for CPU voltage
> ARM: zynq: DT: Migrate UART to Cadence binding
> ARM: zynq: DT: Remove 222 MHz OPP
> spi: Fix zynq SPI binding
> ARM: zynq: DT: Fix GEM register area size
> ARM: zynq: DT: Use the zynq binding with macb
> ARM: zynq: DT: Clean up timer device tree nodes
> ARM: zynq: DT: Cleanup address-cells and size-cells
> ARM: zynq: DT: Add pinctrl node
> ARM: zynq: DT: Add reference to bus node
> ARM: zynq: DT: Sync zc702/zc706/zed/zybo DT with kernel
> ARM: zynq: DT: Update years in copyright
> ARM: zynq: DT: Get rid of ps-clk-frequency
> ARM: zynq: DT: Add missing interrupt for L2 pl310
> ARM: zynq: DT: Add zc702 pushbuttons to DT as gpio-keys
> ARM: zynq: DT: Update zc770 dtses
> ARM: zynq: Add support for zc770-xm011
> ARM: zynqmp: Wire up ethernet controllers
> ARM: zynqmp: Wire up SATA for the board
> zynqmp: Show EL level where U-Boot runs
> net: gem: Extend timeout value
> zynq: Fix typo in Makefile about custom ps7_init file
> spi: zynq_spi: Simplify debug macro
> cmd_mp: Add support for showing all CPU status by one command
>
> Siva Durga Prasad Paladugu (7):
> zynqmp: gem: Set data bus width to 64bit for arm64
> zynqmp: gem: Flush the rx buffers while transmitting
> zynq: gem: Increase the Rx buffer descriptors to 32
> zynqmp: Kconfig: Move zynqmp Kconfig
> zynqmp: Define ep config for ZynqMP
> Kconfig: zynqmp: Move CONFIG_SYS_TEXT_BASE to defconfig
> zynqmp: Provide option to enable uart dcc support for zynqmp
>
> Kconfig | 2 +-
> arch/arm/Kconfig | 5 ++-
> arch/arm/cpu/armv8/Makefile | 2 +-
> arch/arm/cpu/armv8/zynqmp/Kconfig | 23
> ++++++++++
> arch/arm/cpu/armv8/zynqmp/Makefile | 1 +
> arch/arm/cpu/armv8/zynqmp/mp.c | 7 +--
> arch/arm/cpu/armv8/zynqmp/slcr.c | 63
> +++++++++++++++++++++++++++
> arch/arm/dts/Makefile | 1 +
> arch/arm/dts/zynq-7000.dtsi | 174
> +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++------------
> arch/arm/dts/zynq-zc702.dts | 372
> ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++--
> arch/arm/dts/zynq-zc706.dts | 293
> +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++--
> arch/arm/dts/zynq-zc770-xm010.dts | 75
> +++++++++++++++++++++++++++++---
> arch/arm/dts/zynq-zc770-xm011.dts | 65
> ++++++++++++++++++++++++++++
> arch/arm/dts/zynq-zc770-xm012.dts | 51
> ++++++++++++++++++++--
> arch/arm/dts/zynq-zc770-xm013.dts | 62
> ++++++++++++++++++++++++--
> arch/arm/dts/zynq-zed.dts | 46
> ++++++++++++++++++--
> arch/arm/dts/zynq-zybo.dts | 38
> ++++++++++++++--
> arch/arm/include/asm/arch-zynqmp/hardware.h | 16
> +++++++
> arch/arm/include/asm/arch-zynqmp/sys_proto.h | 6 +++
> board/xilinx/zynq/Makefile | 2 +-
> board/xilinx/zynqmp/Kconfig | 15
> -------
> board/xilinx/zynqmp/MAINTAINERS | 5 ++-
> board/xilinx/zynqmp/zynqmp.c | 37
> ++++++++++++++++
> common/cmd_mp.c | 22
> ++++++++++
> configs/{xilinx_zynqmp_defconfig => xilinx_zynqmp_ep_defconfig} | 5 ++-
> configs/zynq_zc770_xm011_defconfig | 13
> ++++++
> doc/device-tree-bindings/spi/spi-zynq.txt | 35
> ++++++++-------
> drivers/net/zynq_gem.c | 26
> ++++++++---
> drivers/spi/zynq_spi.c | 4 +-
> include/configs/xilinx_zynqmp.h | 48
> +++++++++++++++++----
> include/configs/xilinx_zynqmp_ep.h | 27
> ++++++++++++
> include/configs/zynq_zc770.h | 3 ++
> 32 files changed, 1427 insertions(+), 117 deletions(-)
> create mode 100644 arch/arm/cpu/armv8/zynqmp/Kconfig
> create mode 100644 arch/arm/cpu/armv8/zynqmp/slcr.c
> create mode 100644 arch/arm/dts/zynq-zc770-xm011.dts
> delete mode 100644 board/xilinx/zynqmp/Kconfig
> rename configs/{xilinx_zynqmp_defconfig => xilinx_zynqmp_ep_defconfig}
> (81%)
> create mode 100644 configs/zynq_zc770_xm011_defconfig
> create mode 100644 include/configs/xilinx_zynqmp_ep.h
>
--
Michal Simek, Ing. (M.Eng), OpenPGP -> KeyID: FE3D1F91
w: www.monstr.eu p: +42-0-721842854
Maintainer of Linux kernel - Microblaze cpu - http://www.monstr.eu/fdt/
Maintainer of Linux kernel - Xilinx Zynq ARM architecture
Microblaze U-BOOT custodian and responsible for u-boot arm zynq platform
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 198 bytes
Desc: OpenPGP digital signature
URL: <http://lists.denx.de/pipermail/u-boot/attachments/20150728/faf1785d/attachment.sig>
next prev parent reply other threads:[~2015-07-28 13:43 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-07-28 13:41 [U-Boot] [GIT PULL] Zynq changes Michal Simek
2015-07-28 13:43 ` Michal Simek [this message]
2015-07-28 15:37 ` Tom Rini
2015-07-28 18:29 ` Michal Simek
-- strict thread matches above, loose matches on Subject: below --
2015-12-07 9:19 Michal Simek
2015-12-07 19:06 ` Tom Rini
2015-11-19 14:09 Michal Simek
2015-11-19 22:07 ` Tom Rini
2015-11-04 14:48 Michal Simek
2015-11-04 22:03 ` Tom Rini
2015-08-19 10:02 Michal Simek
2015-08-20 16:35 ` Tom Rini
2015-05-25 9:17 Michal Simek
2015-05-26 17:36 ` Tom Rini
2015-04-29 9:45 Michal Simek
2015-04-29 14:28 ` Tom Rini
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=55B786F4.3000000@monstr.eu \
--to=monstr@monstr.eu \
--cc=u-boot@lists.denx.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.