From: Felix Fietkau <nbd@openwrt.org>
To: ath10k@lists.infradead.org
Cc: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>,
Kalle Valo <kvalo@qca.qualcomm.com>,
linux-wireless@vger.kernel.org
Subject: Re: [PATCH] ath10k: Add QCA99X0 to supported device list
Date: Wed, 5 Aug 2015 14:21:16 +0200 [thread overview]
Message-ID: <55C1FFBC.7070905@openwrt.org> (raw)
In-Reply-To: <1437478567-11339-1-git-send-email-vthiagar@qti.qualcomm.com>
On 2015-07-21 13:36, Vasanthakumar Thiagarajan wrote:
> Add vendor/device id of QCA99X0 V2.0 to pci id table and
> QCA99X0_HW_2_0_CHIP_ID_REV to ath10k_pci_supp_chips[] for
> QCA99X0 to get detected by the driver.
>
> Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
I just tested a 99X0 card, and I'm getting this:
[ 8.742514] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
[ 8.747173] ath10k_pci 0000:01:00.0: pci irq msi interrupts 1 irq_mode 0 reset_mode 0
[ 11.793314] ath10k_pci 0000:01:00.0: failed to receive initialized event from target: 00000000
[ 11.793344] ath10k_pci 0000:01:00.0: failed to wait for target after cold reset: -110
[ 11.800814] ath10k_pci 0000:01:00.0: failed to reset chip: -110
[ 11.809228] ath10k_pci: probe of 0000:01:00.0 failed with error -110
This is on an AP148 board with Linux 3.18, backports generated from
latest wireless-testing (2015-08-03) + all patches from kvalo's ath
tree.
- Felix
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
WARNING: multiple messages have this Message-ID (diff)
From: Felix Fietkau <nbd@openwrt.org>
To: ath10k@lists.infradead.org
Cc: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>,
linux-wireless@vger.kernel.org,
Kalle Valo <kvalo@qca.qualcomm.com>
Subject: Re: [PATCH] ath10k: Add QCA99X0 to supported device list
Date: Wed, 5 Aug 2015 14:21:16 +0200 [thread overview]
Message-ID: <55C1FFBC.7070905@openwrt.org> (raw)
In-Reply-To: <1437478567-11339-1-git-send-email-vthiagar@qti.qualcomm.com>
On 2015-07-21 13:36, Vasanthakumar Thiagarajan wrote:
> Add vendor/device id of QCA99X0 V2.0 to pci id table and
> QCA99X0_HW_2_0_CHIP_ID_REV to ath10k_pci_supp_chips[] for
> QCA99X0 to get detected by the driver.
>
> Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
I just tested a 99X0 card, and I'm getting this:
[ 8.742514] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)
[ 8.747173] ath10k_pci 0000:01:00.0: pci irq msi interrupts 1 irq_mode 0 reset_mode 0
[ 11.793314] ath10k_pci 0000:01:00.0: failed to receive initialized event from target: 00000000
[ 11.793344] ath10k_pci 0000:01:00.0: failed to wait for target after cold reset: -110
[ 11.800814] ath10k_pci 0000:01:00.0: failed to reset chip: -110
[ 11.809228] ath10k_pci: probe of 0000:01:00.0 failed with error -110
This is on an AP148 board with Linux 3.18, backports generated from
latest wireless-testing (2015-08-03) + all patches from kvalo's ath
tree.
- Felix
next prev parent reply other threads:[~2015-08-05 12:21 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-07-21 11:36 [PATCH] ath10k: Add QCA99X0 to supported device list Vasanthakumar Thiagarajan
2015-07-21 11:36 ` Vasanthakumar Thiagarajan
2015-07-30 14:04 ` Kalle Valo
2015-07-30 14:04 ` Kalle Valo
2015-08-05 12:21 ` Felix Fietkau [this message]
2015-08-05 12:21 ` Felix Fietkau
2015-08-06 7:43 ` Vasanthakumar Thiagarajan
2015-08-06 7:43 ` Vasanthakumar Thiagarajan
2015-08-06 7:59 ` Felix Fietkau
2015-08-06 7:59 ` Felix Fietkau
2015-08-06 18:45 ` Peter Oh
2015-08-06 18:45 ` Peter Oh
2015-08-06 22:00 ` Felix Fietkau
2015-08-06 22:00 ` Felix Fietkau
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=55C1FFBC.7070905@openwrt.org \
--to=nbd@openwrt.org \
--cc=ath10k@lists.infradead.org \
--cc=kvalo@qca.qualcomm.com \
--cc=linux-wireless@vger.kernel.org \
--cc=vthiagar@qti.qualcomm.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.