* delay in the IMXCFG file @ 2015-08-19 8:48 Igor Plyatov 2015-08-19 14:04 ` Sascha Hauer 0 siblings, 1 reply; 4+ messages in thread From: Igor Plyatov @ 2015-08-19 8:48 UTC (permalink / raw) To: barebox Dear all, for debugging purposes I need to add some delays into the <BOARD NAME>.imxcfg file, but does not know which format it is. It looks like some kind of C, but it is confusing. Where is defined "wm 32", "soc", "dcdofs", "loadaddr" command and others? Which commands I can use in the IMXCFG file to create very early delay, before initialization of DRAM? Please help to clarify these things. Best wishes. -- Igor Plyatov _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox ^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: delay in the IMXCFG file 2015-08-19 8:48 delay in the IMXCFG file Igor Plyatov @ 2015-08-19 14:04 ` Sascha Hauer 2015-08-20 12:20 ` Igor Plyatov 0 siblings, 1 reply; 4+ messages in thread From: Sascha Hauer @ 2015-08-19 14:04 UTC (permalink / raw) To: Igor Plyatov; +Cc: barebox Hi Igor, On Wed, Aug 19, 2015 at 11:48:41AM +0300, Igor Plyatov wrote: > Dear all, > > for debugging purposes I need to add some delays into the <BOARD > NAME>.imxcfg file, but does not know which format it is. It looks > like some kind of C, but it is confusing. > > Where is defined "wm 32", "soc", "dcdofs", "loadaddr" command and others? They are interpreted in the imx-image tool, see scripts/imx/README and scripts/imx/imx-image.c. The imx-image tool converts the commands into a dcd table which is understood by the Freescale i.MX ROM Code. The ROM code does not provide a delay command, so what you are looking for does not exist. All the is is a nop command. This is currently not implemented in imx-image, you would have to add it. > > Which commands I can use in the IMXCFG file to create very early > delay, before initialization of DRAM? As said, there is nop. Otherwise there is a 'check' command to poll for setting/clearing bits. See the i.MX reference manual in the "Device Configuration Data (DCD)" section for further information. Sascha -- Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox ^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: delay in the IMXCFG file 2015-08-19 14:04 ` Sascha Hauer @ 2015-08-20 12:20 ` Igor Plyatov 2015-08-20 12:47 ` Sascha Hauer 0 siblings, 1 reply; 4+ messages in thread From: Igor Plyatov @ 2015-08-20 12:20 UTC (permalink / raw) To: Sascha Hauer; +Cc: barebox Dear Sascha, > Hi Igor, > > On Wed, Aug 19, 2015 at 11:48:41AM +0300, Igor Plyatov wrote: >> Dear all, >> >> for debugging purposes I need to add some delays into the <BOARD >> NAME>.imxcfg file, but does not know which format it is. It looks >> like some kind of C, but it is confusing. >> >> Where is defined "wm 32", "soc", "dcdofs", "loadaddr" command and others? > They are interpreted in the imx-image tool, see scripts/imx/README and > scripts/imx/imx-image.c. The imx-image tool converts the commands into a > dcd table which is understood by the Freescale i.MX ROM Code. The ROM > code does not provide a delay command, so what you are looking for does > not exist. All the is is a nop command. This is currently not > implemented in imx-image, you would have to add it. > >> Which commands I can use in the IMXCFG file to create very early >> delay, before initialization of DRAM? > As said, there is nop. Otherwise there is a 'check' command to poll for > setting/clearing bits. > See the i.MX reference manual in the "Device Configuration Data (DCD)" > section for further information. Thank you for explanation above! Everywhere I see references to DCD in the Reference Manual, but I can not find details about DCD in the MCIMX51RM.pdf Rev. 1 2/2010. If you know, please give me a link to document where DCD explained in details, because any attempt to setup GPIO output, fails. Device just does not boot at all. wm 32 0x73f88000 0x689c0319 /* hangup line in flash-header.imxcfg */ Best wishes. -- Igor Plyatov _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox ^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: delay in the IMXCFG file 2015-08-20 12:20 ` Igor Plyatov @ 2015-08-20 12:47 ` Sascha Hauer 0 siblings, 0 replies; 4+ messages in thread From: Sascha Hauer @ 2015-08-20 12:47 UTC (permalink / raw) To: Igor Plyatov; +Cc: barebox On Thu, Aug 20, 2015 at 03:20:54PM +0300, Igor Plyatov wrote: > Dear Sascha, > > >Hi Igor, > > > >On Wed, Aug 19, 2015 at 11:48:41AM +0300, Igor Plyatov wrote: > >>Dear all, > >> > >>for debugging purposes I need to add some delays into the <BOARD > >>NAME>.imxcfg file, but does not know which format it is. It looks > >>like some kind of C, but it is confusing. > >> > >>Where is defined "wm 32", "soc", "dcdofs", "loadaddr" command and others? > >They are interpreted in the imx-image tool, see scripts/imx/README and > >scripts/imx/imx-image.c. The imx-image tool converts the commands into a > >dcd table which is understood by the Freescale i.MX ROM Code. The ROM > >code does not provide a delay command, so what you are looking for does > >not exist. All the is is a nop command. This is currently not > >implemented in imx-image, you would have to add it. > > > >>Which commands I can use in the IMXCFG file to create very early > >>delay, before initialization of DRAM? > >As said, there is nop. Otherwise there is a 'check' command to poll for > >setting/clearing bits. > >See the i.MX reference manual in the "Device Configuration Data (DCD)" > >section for further information. > > Thank you for explanation above! > > Everywhere I see references to DCD in the Reference Manual, but I > can not find details about DCD in the MCIMX51RM.pdf Rev. 1 2/2010. On i.MX51 the DCD data is indeed much simpler, there are no 'check' or 'nop' commands. Instead the only command is 'wm' for write memory. You can only choose the access width. The additional commands I mentioned only exist on i.MX53 and newer. I just realized that most of the system boot description is missing in the i.MX51 Reference Manual and wonder how I ever managed to boot this successfully. Have a look in the i.MX35 Reference Manual, the DCD layout is described there. It should be identical on i.MX51. > > If you know, please give me a link to document where DCD explained > in details, because any attempt to setup GPIO output, fails. Device > just does not boot at all. > > wm 32 0x73f88000 0x689c0319 /* hangup line in flash-header.imxcfg */ Not all modules can be accessed with DCD data. Information again is missing in the i.MX51 Manual, but the i.MX35 Manual has "Table 7-11. DCD Valid Modules". GPIO is missing in this table, so you can't access it with DCD data. It's probably the same on i.MX51. Sascha -- Pengutronix e.K. | | Industrial Linux Solutions | http://www.pengutronix.de/ | Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ barebox mailing list barebox@lists.infradead.org http://lists.infradead.org/mailman/listinfo/barebox ^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2015-08-20 12:48 UTC | newest] Thread overview: 4+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2015-08-19 8:48 delay in the IMXCFG file Igor Plyatov 2015-08-19 14:04 ` Sascha Hauer 2015-08-20 12:20 ` Igor Plyatov 2015-08-20 12:47 ` Sascha Hauer
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.