* New CT firmware beta-15 available.
@ 2015-08-13 18:03 Ben Greear
2015-09-09 22:33 ` Igor Pavlov
0 siblings, 1 reply; 5+ messages in thread
From: Ben Greear @ 2015-08-13 18:03 UTC (permalink / raw)
To: ath10k
I've just uploaded the latest beta-15 firmware build.
It has a few fixes related to rate-ctrl, and it can also
transmit on a Monitor interface now. The monitor TX packets
are all sent out at 1Mbps encoding rate currently (though
a better use of radiotap might give up to 6Mbps, perhaps),
and all 3 of the MAC addresses in the ieee80211 header
are that of the Monitor device.
I think if someone cared it would be easy enough to
make the driver add real peers to the Monitor device,
but I'm not sure what good that would do.
And, some day, maybe there could be a way to pass rate-ctrl
info to the firmware so that you could specific particular
rates...
The firmware has a few hacks that should let this feature work
on an un-patched driver, I think. I was testing on my 4.0.4
kernel, however.
Thanks,
Ben
--
Ben Greear <greearb@candelatech.com>
Candela Technologies Inc http://www.candelatech.com
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: New CT firmware beta-15 available.
2015-08-13 18:03 New CT firmware beta-15 available Ben Greear
@ 2015-09-09 22:33 ` Igor Pavlov
2015-09-09 22:58 ` Ben Greear
0 siblings, 1 reply; 5+ messages in thread
From: Igor Pavlov @ 2015-09-09 22:33 UTC (permalink / raw)
To: ath10k; +Cc: Ben Greear
I have a few logs from my usage of the
firmware-2-ct-full-community.bin (md5:
b89acccb0bd595d53767cfeab85daa9e).
The host OS is the OpenWRT v15.05-rc3
# lspci -nn -qq
00:05.0 Network controller [0280]: Qualcomm Atheros QCA986x/988x
802.11ac Wireless Network Adapter [168c:003c]
00:06.0 Network controller [0280]: Qualcomm Atheros QCA986x/988x
802.11ac Wireless Network Adapter [168c:003c]
The 1st adapter is the Embedded Works EW5260AC (QCA9880-2R4E).
The 2nd adapter is the Doodle Labs ACM-DB-3 (QCA9890).
I have no idea why they have the same PCI ID's. It may be ok.
#1
[ 7475.763269] ath10k_pci 0000:00:05.0: SWBA overrun on vdev 0,
skipped old beacon
... (a lot of them)
[376051.167238] ath10k_pci 0000:00:05.0: SWBA overrun on vdev 0,
skipped old beacon
[376053.124595] wlan0: failed to remove key (0, xx:xx:xx:xx:xx:xx)
from hardware (-11)
[376055.370656] ath10k_warn: 41 callbacks suppressed
[376055.371099] ath10k_pci 0000:00:05.0: SWBA overrun on vdev 0,
skipped old beacon
...
[376056.088326] ath10k_pci 0000:00:05.0: SWBA overrun on vdev 0,
skipped old beacon
[376056.127516] ath10k_pci 0000:00:05.0: failed to delete peer
yy:yy:yy:yy:yy:yy for vdev 0: -11
[376056.128253] ------------[ cut here ]------------
[376056.128677] WARNING: CPU: 0 PID: 1699 at
/home/buildbot/slave-local/x86_64/build/build_dir/target-x86_64_uClibc-0.9.33.2/linux-x86_64/compat-wireless-2015-03-09/net/mac80211/sta_info.c:909
sta_set_sinfo+0x659/0x710 [mac80211]()
[376056.130364] Modules linked in: pppoe ppp_async iptable_nat pppox
ppp_generic nf_nat_ipv4 nf_conntrack_ipv6 nf_conntrack_ipv4 ipt_REJECT
ipt_MASQUERADE xt_time xt_tcpudp xt_tcpmss xt_statistic xt_state
xt_recent xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_id
xt_hl xt_helper xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit
xt_connbytes xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_HL xt_DSCP
xt_CT xt_CLASSIFY slhc r8169 nf_reject_ipv4 nf_nat_masquerade_ipv4
nf_nat_ftp nf_nat nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4
nf_conntrack_rtcache nf_conntrack_ftp iptable_raw iptable_mangle
iptable_filter ipt_ECN ip_tables e1000e crc_ccitt act_connmark
nf_conntrack act_skbedit act_mirred em_u32 cls_u32 cls_tcindex
cls_flow cls_route cls_fw sch_hfsc sch_ingress ath10k_pci ath10k_core
ath mac80211 cfg80211 compat ip6t_REJECT nf_reject_ipv6 nf_log_ipv6
nf_log_common ip6table_raw ip6table_mangle ip6table_filter ip6_tables
x_tables e1000 ifb ipv6 arc4 crypto_blkcipher ptp pps_core mii
[376056.139315] CPU: 0 PID: 1699 Comm: hostapd Not tainted 3.18.17 #1
[376056.139847] 0000000000000000 0000000000000009 ffffffff813df544
0000000000000000
[376056.140564] ffffffff8103d29d ffff88000ed06000 ffff88000ef30d40
ffff88000e26f730
[376056.141283] ffff88000ecda740 0000000000000000 ffffffffa00fcb39
000000000de2b740
[376056.141999] Call Trace:
[376056.142234] [<ffffffff813df544>] ? dump_stack+0x41/0x51
[376056.142705] [<ffffffff8103d29d>] ? warn_slowpath_common+0x6d/0x90
[376056.143248] [<ffffffffa00fcb39>] ? sta_set_sinfo+0x659/0x710 [mac80211]
[376056.143835] [<ffffffffa00fcc11>] ? __sta_info_destroy+0x21/0x30 [mac80211]
[376056.144440] [<ffffffffa00fcca2>] ?
sta_info_destroy_addr_bss+0x32/0x50 [mac80211]
[376056.145103] [<ffffffffa00c17c8>] ?
cfg80211_check_station_change+0xba8/0xf30 [cfg80211]
[376056.145808] [<ffffffff8135ccc5>] ? genl_family_rcv_msg+0x285/0x300
[376056.146356] [<ffffffff8135cdb5>] ? genl_rcv_msg+0x75/0xa0
[376056.146836] [<ffffffff8135cd40>] ? genl_family_rcv_msg+0x300/0x300
[376056.147381] [<ffffffff8135c12d>] ? netlink_rcv_skb+0x3d/0x90
[376056.147883] [<ffffffff8135ca2f>] ? genl_rcv+0x1f/0x30
[376056.148336] [<ffffffff8135bab9>] ? netlink_unicast+0x119/0x200
[376056.148850] [<ffffffff8135bf67>] ? netlink_sendmsg+0x347/0x3c0
[376056.149361] [<ffffffff8131f313>] ? sock_sendmsg+0x63/0x80
[376056.149834] [<ffffffff81320e72>] ? move_addr_to_kernel+0x22/0x40
[376056.150363] [<ffffffff8132cae8>] ? verify_iovec+0x58/0xc0
[376056.150844] [<ffffffff81320a47>] ? ___sys_sendmsg.part.34+0x207/0x230
[376056.151410] [<ffffffff81320ba1>] ? ___sys_recvmsg.part.35+0x131/0x180
[376056.151978] [<ffffffff81060656>] ? pick_next_task_fair+0x126/0x3f0
[376056.152523] [<ffffffff810f5a7f>] ? __inode_wait_for_writeback+0x5f/0xa0
[376056.153102] [<ffffffff811071b2>] ? fsnotify_clear_marks_by_inode+0x22/0x120
[376056.153709] [<ffffffff81320046>] ? sock_destroy_inode+0x16/0x30
[376056.154233] [<ffffffff810e7a48>] ? __dentry_kill+0x168/0x1a0
[376056.154737] [<ffffffff810e7bb1>] ? dput+0x131/0x160
[376056.155178] [<ffffffff810d55ec>] ? __fput+0x17c/0x1b0
[376056.155631] [<ffffffff813219a6>] ? __sys_sendmsg+0x46/0x70
[376056.156111] [<ffffffff813e39c9>] ? system_call_fastpath+0x12/0x17
[376056.156650] ---[ end trace b976155855a8d0dd ]---
[376056.157260] ath10k_pci 0000:00:05.0: cipher 0 is not supported
[376056.157785] ------------[ cut here ]------------
[376056.158201] WARNING: CPU: 0 PID: 1699 at
/home/buildbot/slave-local/x86_64/build/build_dir/target-x86_64_uClibc-0.9.33.2/linux-x86_64/compat-wireless-2015-03-09/net/mac80211/sta_info.c:901
sta_set_sinfo+0x599/0x710 [mac80211]()
[376056.159905] Modules linked in: pppoe ppp_async iptable_nat pppox
ppp_generic nf_nat_ipv4 nf_conntrack_ipv6 nf_conntrack_ipv4 ipt_REJECT
ipt_MASQUERADE xt_time xt_tcpudp xt_tcpmss xt_statistic xt_state
xt_recent xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_id
xt_hl xt_helper xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit
xt_connbytes xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_HL xt_DSCP
xt_CT xt_CLASSIFY slhc r8169 nf_reject_ipv4 nf_nat_masquerade_ipv4
nf_nat_ftp nf_nat nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4
nf_conntrack_rtcache nf_conntrack_ftp iptable_raw iptable_mangle
iptable_filter ipt_ECN ip_tables e1000e crc_ccitt act_connmark
nf_conntrack act_skbedit act_mirred em_u32 cls_u32 cls_tcindex
cls_flow cls_route cls_fw sch_hfsc sch_ingress ath10k_pci ath10k_core
ath mac80211 cfg80211 compat ip6t_REJECT nf_reject_ipv6 nf_log_ipv6
nf_log_common ip6table_raw ip6table_mangle ip6table_filter ip6_tables
x_tables e1000 ifb ipv6 arc4 crypto_blkcipher ptp pps_core mii
[376056.168869] CPU: 0 PID: 1699 Comm: hostapd Tainted: G W
3.18.17 #1
[376056.169498] 0000000000000000 0000000000000009 ffffffff813df544
0000000000000000
[376056.170221] ffffffff8103d29d ffff88000ed00000 ffff88000ef30d40
ffff88000e26f730
[376056.170934] ffff88000ecda740 0000000000000000 ffffffffa00fca79
000000000de2b740
[376056.171654] Call Trace:
[376056.171886] [<ffffffff813df544>] ? dump_stack+0x41/0x51
[376056.172354] [<ffffffff8103d29d>] ? warn_slowpath_common+0x6d/0x90
[376056.172898] [<ffffffffa00fca79>] ? sta_set_sinfo+0x599/0x710 [mac80211]
[376056.173482] [<ffffffffa00fcc11>] ? __sta_info_destroy+0x21/0x30 [mac80211]
[376056.174093] [<ffffffffa00fcca2>] ?
sta_info_destroy_addr_bss+0x32/0x50 [mac80211]
[376056.174760] [<ffffffffa00c17c8>] ?
cfg80211_check_station_change+0xba8/0xf30 [cfg80211]
[376056.175467] [<ffffffff8135ccc5>] ? genl_family_rcv_msg+0x285/0x300
[376056.176016] [<ffffffff8135cdb5>] ? genl_rcv_msg+0x75/0xa0
[376056.176498] [<ffffffff8135cd40>] ? genl_family_rcv_msg+0x300/0x300
[376056.177048] [<ffffffff8135c12d>] ? netlink_rcv_skb+0x3d/0x90
[376056.177555] [<ffffffff8135ca2f>] ? genl_rcv+0x1f/0x30
[376056.178009] [<ffffffff8135bab9>] ? netlink_unicast+0x119/0x200
[376056.178531] [<ffffffff8135bf67>] ? netlink_sendmsg+0x347/0x3c0
[376056.179054] [<ffffffff8131f313>] ? sock_sendmsg+0x63/0x80
[376056.179538] [<ffffffff81320e72>] ? move_addr_to_kernel+0x22/0x40
[376056.180071] [<ffffffff8132cae8>] ? verify_iovec+0x58/0xc0
[376056.180554] [<ffffffff81320a47>] ? ___sys_sendmsg.part.34+0x207/0x230
[376056.181123] [<ffffffff811071b2>] ? fsnotify_clear_marks_by_inode+0x22/0x120
[376056.181735] [<ffffffff81320046>] ? sock_destroy_inode+0x16/0x30
[376056.182260] [<ffffffff810e7a48>] ? __dentry_kill+0x168/0x1a0
[376056.182764] [<ffffffff810e7bb1>] ? dput+0x131/0x160
[376056.183205] [<ffffffff810d55ec>] ? __fput+0x17c/0x1b0
[376056.183660] [<ffffffff813219a6>] ? __sys_sendmsg+0x46/0x70
[376056.184153] [<ffffffff813e39c9>] ? system_call_fastpath+0x12/0x17
[376056.184696] ---[ end trace b976155855a8d0de ]---
[379888.155644] ath10k_warn: 16 callbacks suppressed
[379888.156191] ath10k_pci 0000:00:05.0: Spurious quick kickout for
STA yy:yy:yy:yy:yy:yy
#2
...
[69284.327377] ath10k_pci 0000:00:05.0: failed to add peer
xx:xx:xx:xx:xx:xx for vdev 0 when adding a new sta: -105
...
[69284.365197] ath10k_pci 0000:00:05.0: failed to add peer
xx:xx:xx:xx:xx:xx for vdev 0 when adding a new sta: -105
[69296.111608] ath10k_warn: 4 callbacks suppressed
[69296.112057] ath10k_pci 0000:00:05.0: failed to add peer
xx:xx:xx:xx:xx:xx for vdev 0 when adding a new sta: -105
...
[69307.886488] ath10k_pci 0000:00:05.0: failed to add peer
xx:xx:xx:xx:xx:xx for vdev 0 when adding a new sta: -105
[69312.147837] ath10k_pci 0000:00:05.0: SWBA overrun on vdev 0,
skipped old beacon
[69312.968019] ath10k_pci 0000:00:05.0: SWBA overrun on vdev 0,
skipped old beacon
[69315.838662] ath10k_pci 0000:00:05.0: SWBA overrun on vdev 0,
skipped old beacon
...
#3
[39061.412447] ath10k_pci 0000:00:05.0: SWBA overrun on vdev 0,
skipped old beacon
...
[39062.335152] ath10k_pci 0000:00:05.0: SWBA overrun on vdev 0,
skipped old beacon
[39064.306407] wlan0: failed to remove key (0, xx:xx:xx:xx:xx:xx) from
hardware (-11)
[39066.538512] ath10k_warn: 41 callbacks suppressed
[39066.539038] ath10k_pci 0000:00:05.0: SWBA overrun on vdev 0,
skipped old beacon
...
[39067.256165] ath10k_pci 0000:00:05.0: SWBA overrun on vdev 0,
skipped old beacon
[39067.309893] ath10k_pci 0000:00:05.0: failed to delete peer
yy:yy:yy:yy:yy:yy for vdev 0: -11
[39067.310857] ------------[ cut here ]------------
[39067.311399] WARNING: CPU: 0 PID: 1779 at
/home/buildbot/slave-local/x86_64/build/build_dir/target-x86_64_uClibc-0.9.33.2/linux-x86_64/compat-wireless-2015-03-09/net/mac80211/sta_info.c:909
sta_set_sinfo+0x659/0x710 [mac80211]()
[39067.313562] Modules linked in: pppoe ppp_async iptable_nat pppox
ppp_generic nf_nat_ipv4 nf_conntrack_ipv6 nf_conntrack_ipv4 ipt_REJECT
ipt_MASQUERADE xt_time xt_tcpudp xt_tcpmss xt_statistic xt_state
xt_recent xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_id
xt_hl xt_helper xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit
xt_connbytes xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_HL xt_DSCP
xt_CT xt_CLASSIFY slhc r8169 nf_reject_ipv4 nf_nat_masquerade_ipv4
nf_nat_ftp nf_nat nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4
nf_conntrack_rtcache nf_conntrack_ftp iptable_raw iptable_mangle
iptable_filter ipt_ECN ip_tables e1000e crc_ccitt act_connmark
nf_conntrack act_skbedit act_mirred em_u32 cls_u32 cls_tcindex
cls_flow cls_route cls_fw sch_hfsc sch_ingress ath10k_pci ath10k_core
ath mac80211 cfg80211 compat ip6t_REJECT nf_reject_ipv6 nf_log_ipv6
nf_log_common ip6table_raw ip6table_mangle ip6table_filter ip6_tables
x_tables e1000 ifb ipv6 arc4 crypto_blkcipher ptp pps_core mii
[39067.323939] CPU: 0 PID: 1779 Comm: hostapd Not tainted 3.18.17 #1
[39067.324485] 0000000000000000 0000000000000009 ffffffff813df544
0000000000000000
[39067.325205] ffffffff8103d29d ffff88000eddf000 ffff88000e6f0d40
ffff88000d93b730
[39067.325928] ffff88000dd92740 0000000000000000 ffffffffa00fcb39
000000000dcc2700
[39067.326669] Call Trace:
[39067.326900] [<ffffffff813df544>] ? dump_stack+0x41/0x51
[39067.327375] [<ffffffff8103d29d>] ? warn_slowpath_common+0x6d/0x90
[39067.327916] [<ffffffffa00fcb39>] ? sta_set_sinfo+0x659/0x710 [mac80211]
[39067.328501] [<ffffffffa00fcc11>] ? __sta_info_destroy+0x21/0x30 [mac80211]
[39067.329101] [<ffffffffa00fcca2>] ?
sta_info_destroy_addr_bss+0x32/0x50 [mac80211]
[39067.329770] [<ffffffffa00c17c8>] ?
cfg80211_check_station_change+0xba8/0xf30 [cfg80211]
[39067.330484] [<ffffffff8135ccc5>] ? genl_family_rcv_msg+0x285/0x300
[39067.331032] [<ffffffff8135cdb5>] ? genl_rcv_msg+0x75/0xa0
[39067.331513] [<ffffffff8135cd40>] ? genl_family_rcv_msg+0x300/0x300
[39067.332058] [<ffffffff8135c12d>] ? netlink_rcv_skb+0x3d/0x90
[39067.332558] [<ffffffff8135ca2f>] ? genl_rcv+0x1f/0x30
[39067.333007] [<ffffffff8135bab9>] ? netlink_unicast+0x119/0x200
[39067.333525] [<ffffffff8135bf67>] ? netlink_sendmsg+0x347/0x3c0
[39067.334036] [<ffffffff8131f313>] ? sock_sendmsg+0x63/0x80
[39067.334513] [<ffffffff81320e72>] ? move_addr_to_kernel+0x22/0x40
[39067.335040] [<ffffffff8132cae8>] ? verify_iovec+0x58/0xc0
[39067.335517] [<ffffffff81320a47>] ? ___sys_sendmsg.part.34+0x207/0x230
[39067.336085] [<ffffffff81320ba1>] ? ___sys_recvmsg.part.35+0x131/0x180
[39067.336653] [<ffffffff81060656>] ? pick_next_task_fair+0x126/0x3f0
[39067.337198] [<ffffffff810f5a7f>] ? __inode_wait_for_writeback+0x5f/0xa0
[39067.337777] [<ffffffff811071b2>] ? fsnotify_clear_marks_by_inode+0x22/0x120
[39067.338386] [<ffffffff81320046>] ? sock_destroy_inode+0x16/0x30
[39067.338908] [<ffffffff810e7a48>] ? __dentry_kill+0x168/0x1a0
[39067.339410] [<ffffffff810e7bb1>] ? dput+0x131/0x160
[39067.339841] [<ffffffff810d55ec>] ? __fput+0x17c/0x1b0
[39067.340287] [<ffffffff813219a6>] ? __sys_sendmsg+0x46/0x70
[39067.340779] [<ffffffff813e39c9>] ? system_call_fastpath+0x12/0x17
[39067.341310] ---[ end trace c3f6cd2181514f7b ]---
[39067.341984] ath10k_pci 0000:00:05.0: cipher 0 is not supported
[39067.342497] ------------[ cut here ]------------
[39067.342922] WARNING: CPU: 0 PID: 1779 at
/home/buildbot/slave-local/x86_64/build/build_dir/target-x86_64_uClibc-0.9.33.2/linux-x86_64/compat-wireless-2015-03-09/net/mac80211/sta_info.c:901
sta_set_sinfo+0x599/0x710 [mac80211]()
[39067.344615] Modules linked in: pppoe ppp_async iptable_nat pppox
ppp_generic nf_nat_ipv4 nf_conntrack_ipv6 nf_conntrack_ipv4 ipt_REJECT
ipt_MASQUERADE xt_time xt_tcpudp xt_tcpmss xt_statistic xt_state
xt_recent xt_nat xt_multiport xt_mark xt_mac xt_limit xt_length xt_id
xt_hl xt_helper xt_ecn xt_dscp xt_conntrack xt_connmark xt_connlimit
xt_connbytes xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_HL xt_DSCP
xt_CT xt_CLASSIFY slhc r8169 nf_reject_ipv4 nf_nat_masquerade_ipv4
nf_nat_ftp nf_nat nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4
nf_conntrack_rtcache nf_conntrack_ftp iptable_raw iptable_mangle
iptable_filter ipt_ECN ip_tables e1000e crc_ccitt act_connmark
nf_conntrack act_skbedit act_mirred em_u32 cls_u32 cls_tcindex
cls_flow cls_route cls_fw sch_hfsc sch_ingress ath10k_pci ath10k_core
ath mac80211 cfg80211 compat ip6t_REJECT nf_reject_ipv6 nf_log_ipv6
nf_log_common ip6table_raw ip6table_mangle ip6table_filter ip6_tables
x_tables e1000 ifb ipv6 arc4 crypto_blkcipher ptp pps_core mii
[39067.353685] CPU: 0 PID: 1779 Comm: hostapd Tainted: G W
3.18.17 #1
[39067.354314] 0000000000000000 0000000000000009 ffffffff813df544
0000000000000000
[39067.355028] ffffffff8103d29d ffff88000e6bf000 ffff88000e6f0d40
ffff88000d93b730
[39067.355777] ffff88000dd92740 0000000000000000 ffffffffa00fca79
000000000dcc2700
[39067.356488] Call Trace:
[39067.356715] [<ffffffff813df544>] ? dump_stack+0x41/0x51
[39067.357178] [<ffffffff8103d29d>] ? warn_slowpath_common+0x6d/0x90
[39067.357717] [<ffffffffa00fca79>] ? sta_set_sinfo+0x599/0x710 [mac80211]
[39067.358309] [<ffffffffa00fcc11>] ? __sta_info_destroy+0x21/0x30 [mac80211]
[39067.358928] [<ffffffffa00fcca2>] ?
sta_info_destroy_addr_bss+0x32/0x50 [mac80211]
[39067.359593] [<ffffffffa00c17c8>] ?
cfg80211_check_station_change+0xba8/0xf30 [cfg80211]
[39067.360298] [<ffffffff8135ccc5>] ? genl_family_rcv_msg+0x285/0x300
[39067.360875] [<ffffffff8135cdb5>] ? genl_rcv_msg+0x75/0xa0
[39067.361348] [<ffffffff8135cd40>] ? genl_family_rcv_msg+0x300/0x300
[39067.361887] [<ffffffff8135c12d>] ? netlink_rcv_skb+0x3d/0x90
[39067.362384] [<ffffffff8135ca2f>] ? genl_rcv+0x1f/0x30
[39067.362830] [<ffffffff8135bab9>] ? netlink_unicast+0x119/0x200
[39067.363343] [<ffffffff8135bf67>] ? netlink_sendmsg+0x347/0x3c0
[39067.363863] [<ffffffff8131f313>] ? sock_sendmsg+0x63/0x80
[39067.364344] [<ffffffff81320e72>] ? move_addr_to_kernel+0x22/0x40
[39067.364876] [<ffffffff8132cae8>] ? verify_iovec+0x58/0xc0
[39067.365350] [<ffffffff81320a47>] ? ___sys_sendmsg.part.34+0x207/0x230
[39067.365919] [<ffffffff81320ba1>] ? ___sys_recvmsg.part.35+0x131/0x180
[39067.366483] [<ffffffff8131fe21>] ? sockfd_lookup_light+0x11/0x70
[39067.367016] [<ffffffff810d55ec>] ? __fput+0x17c/0x1b0
[39067.367473] [<ffffffff813219a6>] ? __sys_sendmsg+0x46/0x70
[39067.367972] [<ffffffff813e39c9>] ? system_call_fastpath+0x12/0x17
[39067.368520] ---[ end trace c3f6cd2181514f7c ]---
[42801.354141] ath10k_warn: 8 callbacks suppressed
[42801.354554] ath10k_pci 0000:00:05.0: Spurious quick kickout for STA
yy:yy:yy:yy:yy:yy
[62612.023120] ath10k_pci 0000:00:05.0: SWBA overrun on vdev 0,
skipped old beacon
...
[63185.118114] ath10k_pci 0000:00:05.0: SWBA overrun on vdev 0,
skipped old beacon
--
Igor
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: New CT firmware beta-15 available.
2015-09-09 22:33 ` Igor Pavlov
@ 2015-09-09 22:58 ` Ben Greear
2015-09-10 2:14 ` Igor Pavlov
0 siblings, 1 reply; 5+ messages in thread
From: Ben Greear @ 2015-09-09 22:58 UTC (permalink / raw)
To: Igor Pavlov, ath10k
On 09/09/2015 03:33 PM, Igor Pavlov wrote:
> I have a few logs from my usage of the
> firmware-2-ct-full-community.bin (md5:
> b89acccb0bd595d53767cfeab85daa9e).
> The host OS is the OpenWRT v15.05-rc3
Does it act any better if you use the official 'firmware-2.bin'
for firmware?
What kernel/backport is your OpenWRT based on?
Thanks,
Ben
--
Ben Greear <greearb@candelatech.com>
Candela Technologies Inc http://www.candelatech.com
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: New CT firmware beta-15 available.
2015-09-09 22:58 ` Ben Greear
@ 2015-09-10 2:14 ` Igor Pavlov
2015-09-10 14:42 ` Ben Greear
0 siblings, 1 reply; 5+ messages in thread
From: Igor Pavlov @ 2015-09-10 2:14 UTC (permalink / raw)
To: ath10k; +Cc: Ben Greear
2015-09-10 1:58 GMT+03:00 Ben Greear <greearb@candelatech.com>:
> Does it act any better if you use the official 'firmware-2.bin'
> for firmware?
No, it's unstable.
I haven't found stable firmware version yet.
I tried firmware-4.bin (md5: eca8fd35aec383278223efdf35a00f33,
0067c0c5dff032fd45137815cdd15134) with the fresh Arch Linux, it's
unstable too:
# uname -a
Linux 4.1.2-2-ARCH #1 SMP PREEMPT Wed Jul 15 08:30:32 UTC 2015 x86_64 GNU/Linux
> What kernel/backport is your OpenWRT based on?
It's standard OpenWRT image from there:
https://downloads.openwrt.org/chaos_calmer/15.05-rc3/x86/64/
# uname -a
Linux 3.18.17 #1 SMP Fri Jul 3 20:58:35 CEST 2015 x86_64 GNU/Linux
--
Igor
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 5+ messages in thread
* Re: New CT firmware beta-15 available.
2015-09-10 2:14 ` Igor Pavlov
@ 2015-09-10 14:42 ` Ben Greear
0 siblings, 0 replies; 5+ messages in thread
From: Ben Greear @ 2015-09-10 14:42 UTC (permalink / raw)
To: Igor Pavlov, ath10k
On 09/09/2015 07:14 PM, Igor Pavlov wrote:
> 2015-09-10 1:58 GMT+03:00 Ben Greear <greearb@candelatech.com>:
>> Does it act any better if you use the official 'firmware-2.bin'
>> for firmware?
>
> No, it's unstable.
> I haven't found stable firmware version yet.
>
> I tried firmware-4.bin (md5: eca8fd35aec383278223efdf35a00f33,
> 0067c0c5dff032fd45137815cdd15134) with the fresh Arch Linux, it's
> unstable too:
> # uname -a
> Linux 4.1.2-2-ARCH #1 SMP PREEMPT Wed Jul 15 08:30:32 UTC 2015 x86_64 GNU/Linux
Can you try CT firmware on this kernel?
>
>> What kernel/backport is your OpenWRT based on?
>
> It's standard OpenWRT image from there:
> https://downloads.openwrt.org/chaos_calmer/15.05-rc3/x86/64/
>
> # uname -a
> Linux 3.18.17 #1 SMP Fri Jul 3 20:58:35 CEST 2015 x86_64 GNU/Linux
This kernel is a bit old...probably a 4.0 or higher kernel is needed.
Thanks,
Ben
>
> --
> Igor
>
--
Ben Greear <greearb@candelatech.com>
Candela Technologies Inc http://www.candelatech.com
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2015-09-10 14:42 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2015-08-13 18:03 New CT firmware beta-15 available Ben Greear
2015-09-09 22:33 ` Igor Pavlov
2015-09-09 22:58 ` Ben Greear
2015-09-10 2:14 ` Igor Pavlov
2015-09-10 14:42 ` Ben Greear
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.