* [PATCH 1/5] ARM: dts: Use GPIO constants for flags cells in exynos3250 boards
2015-10-07 13:14 [PATCH 0/5] ARM: dts: Use GPIO constants for flags cells in exynos boards Javier Martinez Canillas
@ 2015-10-07 13:14 ` Javier Martinez Canillas
2015-10-07 13:14 ` [PATCH 2/5] ARM: dts: Use GPIO constants for flags cells in exynos4120 boards Javier Martinez Canillas
` (4 subsequent siblings)
5 siblings, 0 replies; 7+ messages in thread
From: Javier Martinez Canillas @ 2015-10-07 13:14 UTC (permalink / raw)
To: linux-kernel
Cc: linux-samsung-soc, Kukjin Kim, Krzysztof Kozlowski,
Javier Martinez Canillas
The board DTS are using numeric values instead of the defined GPIO
constanst to express polarity, use them to make the DTS more clear.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
---
arch/arm/boot/dts/exynos3250-monk.dts | 8 ++++----
arch/arm/boot/dts/exynos3250-rinato.dts | 10 +++++-----
2 files changed, 9 insertions(+), 9 deletions(-)
diff --git a/arch/arm/boot/dts/exynos3250-monk.dts b/arch/arm/boot/dts/exynos3250-monk.dts
index 540a0adf2be6..c14129e0761d 100644
--- a/arch/arm/boot/dts/exynos3250-monk.dts
+++ b/arch/arm/boot/dts/exynos3250-monk.dts
@@ -52,13 +52,13 @@
regulator-name = "V_EMMC_2.8V-fixed";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
- gpio = <&gpk0 2 0>;
+ gpio = <&gpk0 2 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
i2c_max77836: i2c-gpio-0 {
compatible = "i2c-gpio";
- gpios = <&gpd0 2 0>, <&gpd0 3 0>;
+ gpios = <&gpd0 2 GPIO_ACTIVE_HIGH>, <&gpd0 3 GPIO_ACTIVE_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
@@ -266,14 +266,14 @@
regulator-name = "V_EMMC_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
- samsung,ext-control-gpios = <&gpk0 2 0>;
+ samsung,ext-control-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>;
};
ldo12_reg: LDO12 {
regulator-name = "V_EMMC_2.8V";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
- samsung,ext-control-gpios = <&gpk0 2 0>;
+ samsung,ext-control-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>;
};
ldo13_reg: LDO13 {
diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/exynos3250-rinato.dts
index 41a5fafb9aa9..830e216f7e10 100644
--- a/arch/arm/boot/dts/exynos3250-rinato.dts
+++ b/arch/arm/boot/dts/exynos3250-rinato.dts
@@ -49,7 +49,7 @@
i2c_max77836: i2c-gpio-0 {
compatible = "i2c-gpio";
- gpios = <&gpd0 2 0>, <&gpd0 3 0>;
+ gpios = <&gpd0 2 GPIO_ACTIVE_HIGH>, <&gpd0 3 GPIO_ACTIVE_HIGH>;
#address-cells = <1>;
#size-cells = <0>;
@@ -188,8 +188,8 @@
reg = <0>;
vdd3-supply = <&ldo16_reg>;
vci-supply = <&ldo20_reg>;
- reset-gpios = <&gpe0 1 0>;
- te-gpios = <&gpx0 6 0>;
+ reset-gpios = <&gpe0 1 GPIO_ACTIVE_HIGH>;
+ te-gpios = <&gpx0 6 GPIO_ACTIVE_HIGH>;
power-on-delay= <30>;
power-off-delay= <120>;
reset-delay = <5>;
@@ -368,14 +368,14 @@
regulator-name = "V_EMMC_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
- samsung,ext-control-gpios = <&gpk0 2 0>;
+ samsung,ext-control-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>;
};
ldo12_reg: LDO12 {
regulator-name = "V_EMMC_2.8V";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
- samsung,ext-control-gpios = <&gpk0 2 0>;
+ samsung,ext-control-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>;
};
ldo13_reg: LDO13 {
--
2.4.3
^ permalink raw reply related [flat|nested] 7+ messages in thread* [PATCH 2/5] ARM: dts: Use GPIO constants for flags cells in exynos4120 boards
2015-10-07 13:14 [PATCH 0/5] ARM: dts: Use GPIO constants for flags cells in exynos boards Javier Martinez Canillas
2015-10-07 13:14 ` [PATCH 1/5] ARM: dts: Use GPIO constants for flags cells in exynos3250 boards Javier Martinez Canillas
@ 2015-10-07 13:14 ` Javier Martinez Canillas
2015-10-07 13:14 ` [PATCH 3/5] ARM: dts: Use GPIO constants for flags cells in exynos4412 boards Javier Martinez Canillas
` (3 subsequent siblings)
5 siblings, 0 replies; 7+ messages in thread
From: Javier Martinez Canillas @ 2015-10-07 13:14 UTC (permalink / raw)
To: linux-kernel
Cc: linux-samsung-soc, Kukjin Kim, Krzysztof Kozlowski,
Javier Martinez Canillas
The board DTS are using numeric values instead of the defined GPIO
constanst to express polarity, use them to make the DTS more clear.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
---
arch/arm/boot/dts/exynos4210-origen.dts | 15 ++++-----
arch/arm/boot/dts/exynos4210-smdkv310.dts | 3 +-
arch/arm/boot/dts/exynos4210-trats.dts | 29 ++++++++---------
arch/arm/boot/dts/exynos4210-universal_c210.dts | 42 +++++++++++++------------
4 files changed, 47 insertions(+), 42 deletions(-)
diff --git a/arch/arm/boot/dts/exynos4210-origen.dts b/arch/arm/boot/dts/exynos4210-origen.dts
index e050d85cdacd..b8f866991bdd 100644
--- a/arch/arm/boot/dts/exynos4210-origen.dts
+++ b/arch/arm/boot/dts/exynos4210-origen.dts
@@ -16,6 +16,7 @@
/dts-v1/;
#include "exynos4210.dtsi"
+#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
@@ -45,7 +46,7 @@
regulator-name = "VMEM_VDD_2.8V";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
- gpio = <&gpx1 1 0>;
+ gpio = <&gpx1 1 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
};
@@ -57,35 +58,35 @@
up {
label = "Up";
- gpios = <&gpx2 0 1>;
+ gpios = <&gpx2 0 GPIO_ACTIVE_LOW>;
linux,code = <KEY_UP>;
gpio-key,wakeup;
};
down {
label = "Down";
- gpios = <&gpx2 1 1>;
+ gpios = <&gpx2 1 GPIO_ACTIVE_LOW>;
linux,code = <KEY_DOWN>;
gpio-key,wakeup;
};
back {
label = "Back";
- gpios = <&gpx1 7 1>;
+ gpios = <&gpx1 7 GPIO_ACTIVE_LOW>;
linux,code = <KEY_BACK>;
gpio-key,wakeup;
};
home {
label = "Home";
- gpios = <&gpx1 6 1>;
+ gpios = <&gpx1 6 GPIO_ACTIVE_LOW>;
linux,code = <KEY_HOME>;
gpio-key,wakeup;
};
menu {
label = "Menu";
- gpios = <&gpx1 5 1>;
+ gpios = <&gpx1 5 GPIO_ACTIVE_LOW>;
linux,code = <KEY_MENU>;
gpio-key,wakeup;
};
@@ -94,7 +95,7 @@
leds {
compatible = "gpio-leds";
status {
- gpios = <&gpx1 3 1>;
+ gpios = <&gpx1 3 GPIO_ACTIVE_LOW>;
linux,default-trigger = "heartbeat";
};
};
diff --git a/arch/arm/boot/dts/exynos4210-smdkv310.dts b/arch/arm/boot/dts/exynos4210-smdkv310.dts
index 043b03caff8f..bc1448ba95d3 100644
--- a/arch/arm/boot/dts/exynos4210-smdkv310.dts
+++ b/arch/arm/boot/dts/exynos4210-smdkv310.dts
@@ -16,6 +16,7 @@
/dts-v1/;
#include "exynos4210.dtsi"
+#include <dt-bindings/gpio/gpio.h>
/ {
model = "Samsung smdkv310 evaluation board based on Exynos4210";
@@ -182,7 +183,7 @@
};
&spi_2 {
- cs-gpios = <&gpc1 2 0>;
+ cs-gpios = <&gpc1 2 GPIO_ACTIVE_HIGH>;
status = "okay";
w25x80@0 {
diff --git a/arch/arm/boot/dts/exynos4210-trats.dts b/arch/arm/boot/dts/exynos4210-trats.dts
index ba34886f8b65..c69e468efd2e 100644
--- a/arch/arm/boot/dts/exynos4210-trats.dts
+++ b/arch/arm/boot/dts/exynos4210-trats.dts
@@ -14,6 +14,7 @@
/dts-v1/;
#include "exynos4210.dtsi"
+#include <dt-bindings/gpio/gpio.h>
/ {
model = "Samsung Trats based on Exynos4210";
@@ -39,7 +40,7 @@
regulator-name = "VMEM_VDD_2.8V";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
- gpio = <&gpk0 2 0>;
+ gpio = <&gpk0 2 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
@@ -48,7 +49,7 @@
regulator-name = "TSP_FIXED_VOLTAGES";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
- gpio = <&gpl0 3 0>;
+ gpio = <&gpl0 3 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
@@ -57,7 +58,7 @@
regulator-name = "8M_AF_2.8V_EN";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
- gpio = <&gpk1 1 0>;
+ gpio = <&gpk1 1 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
@@ -66,7 +67,7 @@
regulator-name = "CAM_IO_EN";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
- gpio = <&gpe2 1 0>;
+ gpio = <&gpe2 1 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
@@ -75,7 +76,7 @@
regulator-name = "8M_1.2V_EN";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
- gpio = <&gpe2 5 0>;
+ gpio = <&gpe2 5 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
@@ -84,7 +85,7 @@
regulator-name = "VT_CORE_1.5V";
regulator-min-microvolt = <1500000>;
regulator-max-microvolt = <1500000>;
- gpio = <&gpe2 2 0>;
+ gpio = <&gpe2 2 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
};
@@ -93,21 +94,21 @@
compatible = "gpio-keys";
vol-down-key {
- gpios = <&gpx2 1 1>;
+ gpios = <&gpx2 1 GPIO_ACTIVE_LOW>;
linux,code = <114>;
label = "volume down";
debounce-interval = <10>;
};
vol-up-key {
- gpios = <&gpx2 0 1>;
+ gpios = <&gpx2 0 GPIO_ACTIVE_LOW>;
linux,code = <115>;
label = "volume up";
debounce-interval = <10>;
};
power-key {
- gpios = <&gpx2 7 1>;
+ gpios = <&gpx2 7 GPIO_ACTIVE_LOW>;
linux,code = <116>;
label = "power";
debounce-interval = <10>;
@@ -115,7 +116,7 @@
};
ok-key {
- gpios = <&gpx3 5 1>;
+ gpios = <&gpx3 5 GPIO_ACTIVE_LOW>;
linux,code = <352>;
label = "ok";
debounce-interval = <10>;
@@ -218,7 +219,7 @@
compatible = "samsung,s6e8aa0";
vdd3-supply = <&vcclcd_reg>;
vci-supply = <&vlcd_reg>;
- reset-gpios = <&gpy4 5 0>;
+ reset-gpios = <&gpy4 5 GPIO_ACTIVE_HIGH>;
power-on-delay= <50>;
reset-delay = <100>;
init-delay = <100>;
@@ -304,9 +305,9 @@
max8997,pmic-ignore-gpiodvs-side-effect;
max8997,pmic-buck125-default-dvs-idx = <0>;
- max8997,pmic-buck125-dvs-gpios = <&gpx0 5 0>,
- <&gpx0 6 0>,
- <&gpl0 0 0>;
+ max8997,pmic-buck125-dvs-gpios = <&gpx0 5 GPIO_ACTIVE_HIGH>,
+ <&gpx0 6 GPIO_ACTIVE_HIGH>,
+ <&gpl0 0 GPIO_ACTIVE_HIGH>;
max8997,pmic-buck1-dvs-voltage = <1350000>, <1300000>,
<1250000>, <1200000>,
diff --git a/arch/arm/boot/dts/exynos4210-universal_c210.dts b/arch/arm/boot/dts/exynos4210-universal_c210.dts
index eb379526e234..896be8f2342d 100644
--- a/arch/arm/boot/dts/exynos4210-universal_c210.dts
+++ b/arch/arm/boot/dts/exynos4210-universal_c210.dts
@@ -14,6 +14,7 @@
/dts-v1/;
#include "exynos4210.dtsi"
+#include <dt-bindings/gpio/gpio.h>
/ {
model = "Samsung Universal C210 based on Exynos4210 rev0";
@@ -65,7 +66,7 @@
regulator-name = "VMEM_VDD_2_8V";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
- gpio = <&gpe1 3 0>;
+ gpio = <&gpe1 3 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
@@ -73,21 +74,21 @@
compatible = "gpio-keys";
vol-up-key {
- gpios = <&gpx2 0 1>;
+ gpios = <&gpx2 0 GPIO_ACTIVE_LOW>;
linux,code = <115>;
label = "volume up";
debounce-interval = <1>;
};
vol-down-key {
- gpios = <&gpx2 1 1>;
+ gpios = <&gpx2 1 GPIO_ACTIVE_LOW>;
linux,code = <114>;
label = "volume down";
debounce-interval = <1>;
};
config-key {
- gpios = <&gpx2 2 1>;
+ gpios = <&gpx2 2 GPIO_ACTIVE_LOW>;
linux,code = <171>;
label = "config";
debounce-interval = <1>;
@@ -95,14 +96,14 @@
};
camera-key {
- gpios = <&gpx2 3 1>;
+ gpios = <&gpx2 3 GPIO_ACTIVE_LOW>;
linux,code = <212>;
label = "camera";
debounce-interval = <1>;
};
power-key {
- gpios = <&gpx2 7 1>;
+ gpios = <&gpx2 7 GPIO_ACTIVE_LOW>;
linux,code = <116>;
label = "power";
debounce-interval = <1>;
@@ -110,7 +111,7 @@
};
ok-key {
- gpios = <&gpx3 5 1>;
+ gpios = <&gpx3 5 GPIO_ACTIVE_LOW>;
linux,code = <352>;
label = "ok";
debounce-interval = <1>;
@@ -122,7 +123,7 @@
regulator-name = "TSP_2_8V";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
- gpio = <&gpe2 3 0>;
+ gpio = <&gpe2 3 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
@@ -131,17 +132,17 @@
#address-cells = <1>;
#size-cells = <0>;
- gpio-sck = <&gpy3 1 0>;
- gpio-mosi = <&gpy3 3 0>;
+ gpio-sck = <&gpy3 1 GPIO_ACTIVE_HIGH>;
+ gpio-mosi = <&gpy3 3 GPIO_ACTIVE_HIGH>;
num-chipselects = <1>;
- cs-gpios = <&gpy4 3 0>;
+ cs-gpios = <&gpy4 3 GPIO_ACTIVE_HIGH>;
lcd@0 {
compatible = "samsung,ld9040";
reg = <0>;
vdd3-supply = <&ldo7_reg>;
vci-supply = <&ldo17_reg>;
- reset-gpios = <&gpy4 5 0>;
+ reset-gpios = <&gpy4 5 GPIO_ACTIVE_HIGH>;
spi-max-frequency = <1200000>;
spi-cpol;
spi-cpha;
@@ -218,13 +219,13 @@
regulator-name = "HDMI_5V";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
- gpio = <&gpe0 1 0>;
+ gpio = <&gpe0 1 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
hdmi_ddc: i2c-ddc {
compatible = "i2c-gpio";
- gpios = <&gpe4 2 0 &gpe4 3 0>;
+ gpios = <&gpe4 2 GPIO_ACTIVE_HIGH &gpe4 3 GPIO_ACTIVE_HIGH>;
i2c-gpio,delay-us = <100>;
#address-cells = <1>;
#size-cells = <0>;
@@ -267,7 +268,7 @@
};
&hdmi {
- hpd-gpio = <&gpx3 7 0>;
+ hpd-gpio = <&gpx3 7 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&hdmi_hpd>;
hdmi-en-supply = <&hdmi_en>;
@@ -311,7 +312,8 @@
compatible = "maxim,max8952";
reg = <0x60>;
- max8952,vid-gpios = <&gpx0 3 0>, <&gpx0 4 0>;
+ max8952,vid-gpios = <&gpx0 3 GPIO_ACTIVE_HIGH>,
+ <&gpx0 4 GPIO_ACTIVE_HIGH>;
max8952,default-mode = <0>;
max8952,dvs-mode-microvolt = <1250000>, <1200000>,
<1050000>, <950000>;
@@ -330,13 +332,13 @@
reg = <0x66>;
max8998,pmic-buck1-default-dvs-idx = <0>;
- max8998,pmic-buck1-dvs-gpios = <&gpx0 5 0>,
- <&gpx0 6 0>;
+ max8998,pmic-buck1-dvs-gpios = <&gpx0 5 GPIO_ACTIVE_HIGH>,
+ <&gpx0 6 GPIO_ACTIVE_HIGH>;
max8998,pmic-buck1-dvs-voltage = <1100000>, <1000000>,
<1100000>, <1000000>;
max8998,pmic-buck2-default-dvs-idx = <0>;
- max8998,pmic-buck2-dvs-gpio = <&gpe2 0 0>;
+ max8998,pmic-buck2-dvs-gpio = <&gpe2 0 GPIO_ACTIVE_HIGH>;
max8998,pmic-buck2-dvs-voltage = <1200000>, <1100000>;
regulators {
@@ -551,7 +553,7 @@
pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4>;
pinctrl-names = "default";
vmmc-supply = <&ldo5_reg>;
- cd-gpios = <&gpx3 4 0>;
+ cd-gpios = <&gpx3 4 GPIO_ACTIVE_HIGH>;
cd-inverted;
status = "okay";
};
--
2.4.3
^ permalink raw reply related [flat|nested] 7+ messages in thread* [PATCH 3/5] ARM: dts: Use GPIO constants for flags cells in exynos4412 boards
2015-10-07 13:14 [PATCH 0/5] ARM: dts: Use GPIO constants for flags cells in exynos boards Javier Martinez Canillas
2015-10-07 13:14 ` [PATCH 1/5] ARM: dts: Use GPIO constants for flags cells in exynos3250 boards Javier Martinez Canillas
2015-10-07 13:14 ` [PATCH 2/5] ARM: dts: Use GPIO constants for flags cells in exynos4120 boards Javier Martinez Canillas
@ 2015-10-07 13:14 ` Javier Martinez Canillas
2015-10-07 13:14 ` [PATCH 4/5] ARM: dts: Use GPIO constants for flags cells in exynos5420/5422/5800 boards Javier Martinez Canillas
` (2 subsequent siblings)
5 siblings, 0 replies; 7+ messages in thread
From: Javier Martinez Canillas @ 2015-10-07 13:14 UTC (permalink / raw)
To: linux-kernel
Cc: linux-samsung-soc, Kukjin Kim, Krzysztof Kozlowski,
Javier Martinez Canillas
The board DTS are using numeric values instead of the defined GPIO
constanst to express polarity, use them to make the DTS more clear.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
---
arch/arm/boot/dts/exynos4412-odroid-common.dtsi | 15 ++++++-----
arch/arm/boot/dts/exynos4412-odroidu3.dts | 2 +-
arch/arm/boot/dts/exynos4412-odroidx.dts | 8 +++---
arch/arm/boot/dts/exynos4412-origen.dts | 15 ++++++-----
arch/arm/boot/dts/exynos4412-tiny4412.dts | 9 ++++---
arch/arm/boot/dts/exynos4412-trats2.dts | 34 ++++++++++++-------------
6 files changed, 43 insertions(+), 40 deletions(-)
diff --git a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
index c3e978d77367..edf0fc8db6ff 100644
--- a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
+++ b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
@@ -11,6 +11,7 @@
#include <dt-bindings/input/input.h>
#include <dt-bindings/clock/maxim,max77686.h>
#include "exynos4412.dtsi"
+#include <dt-bindings/gpio/gpio.h>
/ {
chosen {
@@ -30,7 +31,7 @@
power_key {
interrupt-parent = <&gpx1>;
interrupts = <3 0>;
- gpios = <&gpx1 3 1>;
+ gpios = <&gpx1 3 GPIO_ACTIVE_LOW>;
linux,code = <KEY_POWER>;
label = "power key";
debounce-interval = <10>;
@@ -70,7 +71,7 @@
pinctrl-0 = <&sd1_cd>;
pinctrl-names = "default";
compatible = "mmc-pwrseq-emmc";
- reset-gpios = <&gpk1 2 1>;
+ reset-gpios = <&gpk1 2 GPIO_ACTIVE_LOW>;
};
camera {
@@ -181,7 +182,7 @@
};
&hdmi {
- hpd-gpio = <&gpx3 7 0>;
+ hpd-gpio = <&gpx3 7 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&hdmi_hpd>;
vdd-supply = <&ldo8_reg>;
@@ -207,9 +208,9 @@
compatible = "smsc,usb3503";
reg = <0x08>;
- intn-gpios = <&gpx3 0 0>;
- connect-gpios = <&gpx3 4 0>;
- reset-gpios = <&gpx3 5 0>;
+ intn-gpios = <&gpx3 0 GPIO_ACTIVE_HIGH>;
+ connect-gpios = <&gpx3 4 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpx3 5 GPIO_ACTIVE_HIGH>;
initial-mode = <1>;
};
@@ -482,7 +483,7 @@
pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
pinctrl-names = "default";
vmmc-supply = <&ldo4_reg &ldo21_reg>;
- cd-gpios = <&gpk2 2 0>;
+ cd-gpios = <&gpk2 2 GPIO_ACTIVE_HIGH>;
cd-inverted;
status = "okay";
};
diff --git a/arch/arm/boot/dts/exynos4412-odroidu3.dts b/arch/arm/boot/dts/exynos4412-odroidu3.dts
index 1e6ef99eef59..646ff0bd001a 100644
--- a/arch/arm/boot/dts/exynos4412-odroidu3.dts
+++ b/arch/arm/boot/dts/exynos4412-odroidu3.dts
@@ -27,7 +27,7 @@
compatible = "gpio-leds";
led1 {
label = "led1:heart";
- gpios = <&gpc1 0 1>;
+ gpios = <&gpc1 0 GPIO_ACTIVE_LOW>;
default-state = "on";
linux,default-trigger = "heartbeat";
};
diff --git a/arch/arm/boot/dts/exynos4412-odroidx.dts b/arch/arm/boot/dts/exynos4412-odroidx.dts
index 679ac103ebf6..b44bb682e976 100644
--- a/arch/arm/boot/dts/exynos4412-odroidx.dts
+++ b/arch/arm/boot/dts/exynos4412-odroidx.dts
@@ -26,13 +26,13 @@
compatible = "gpio-leds";
led1 {
label = "led1:heart";
- gpios = <&gpc1 0 1>;
+ gpios = <&gpc1 0 GPIO_ACTIVE_LOW>;
default-state = "on";
linux,default-trigger = "heartbeat";
};
led2 {
label = "led2:mmc0";
- gpios = <&gpc1 2 1>;
+ gpios = <&gpc1 2 GPIO_ACTIVE_LOW>;
default-state = "on";
linux,default-trigger = "mmc0";
};
@@ -44,7 +44,7 @@
home_key {
interrupt-parent = <&gpx2>;
interrupts = <2 0>;
- gpios = <&gpx2 2 0>;
+ gpios = <&gpx2 2 GPIO_ACTIVE_HIGH>;
linux,code = <KEY_HOME>;
label = "home key";
debounce-interval = <10>;
@@ -57,7 +57,7 @@
regulator-name = "p3v3_en";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
- gpio = <&gpa1 1 1>;
+ gpio = <&gpa1 1 GPIO_ACTIVE_LOW>;
enable-active-high;
regulator-always-on;
};
diff --git a/arch/arm/boot/dts/exynos4412-origen.dts b/arch/arm/boot/dts/exynos4412-origen.dts
index 9d528af68c1a..c8d86af2fb98 100644
--- a/arch/arm/boot/dts/exynos4412-origen.dts
+++ b/arch/arm/boot/dts/exynos4412-origen.dts
@@ -14,6 +14,7 @@
/dts-v1/;
#include "exynos4412.dtsi"
+#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/input/input.h>
/ {
@@ -45,7 +46,7 @@
regulator-name = "VMEM_VDD_2.8V";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
- gpio = <&gpx1 1 0>;
+ gpio = <&gpx1 1 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
};
@@ -107,13 +108,13 @@
s5m8767,pmic-buck-default-dvs-idx = <3>;
- s5m8767,pmic-buck-dvs-gpios = <&gpx2 3 0>,
- <&gpx2 4 0>,
- <&gpx2 5 0>;
+ s5m8767,pmic-buck-dvs-gpios = <&gpx2 3 GPIO_ACTIVE_HIGH>,
+ <&gpx2 4 GPIO_ACTIVE_HIGH>,
+ <&gpx2 5 GPIO_ACTIVE_HIGH>;
- s5m8767,pmic-buck-ds-gpios = <&gpm3 5 0>,
- <&gpm3 6 0>,
- <&gpm3 7 0>;
+ s5m8767,pmic-buck-ds-gpios = <&gpm3 5 GPIO_ACTIVE_HIGH>,
+ <&gpm3 6 GPIO_ACTIVE_HIGH>,
+ <&gpm3 7 GPIO_ACTIVE_HIGH>;
s5m8767,pmic-buck2-dvs-voltage = <1250000>, <1200000>,
<1200000>, <1200000>,
diff --git a/arch/arm/boot/dts/exynos4412-tiny4412.dts b/arch/arm/boot/dts/exynos4412-tiny4412.dts
index 525684ca8dc0..4840bbdaa9ec 100644
--- a/arch/arm/boot/dts/exynos4412-tiny4412.dts
+++ b/arch/arm/boot/dts/exynos4412-tiny4412.dts
@@ -13,6 +13,7 @@
/dts-v1/;
#include "exynos4412.dtsi"
+#include <dt-bindings/gpio/gpio.h>
/ {
model = "FriendlyARM TINY4412 board based on Exynos4412";
@@ -31,26 +32,26 @@
led1 {
label = "led1";
- gpios = <&gpm4 0 1>;
+ gpios = <&gpm4 0 GPIO_ACTIVE_LOW>;
default-state = "off";
linux,default-trigger = "heartbeat";
};
led2 {
label = "led2";
- gpios = <&gpm4 1 1>;
+ gpios = <&gpm4 1 GPIO_ACTIVE_LOW>;
default-state = "off";
};
led3 {
label = "led3";
- gpios = <&gpm4 2 1>;
+ gpios = <&gpm4 2 GPIO_ACTIVE_LOW>;
default-state = "off";
};
led4 {
label = "led4";
- gpios = <&gpm4 3 1>;
+ gpios = <&gpm4 3 GPIO_ACTIVE_LOW>;
default-state = "off";
linux,default-trigger = "mmc0";
};
diff --git a/arch/arm/boot/dts/exynos4412-trats2.dts b/arch/arm/boot/dts/exynos4412-trats2.dts
index 93e3bbd4bd49..d8bf4afb8bd9 100644
--- a/arch/arm/boot/dts/exynos4412-trats2.dts
+++ b/arch/arm/boot/dts/exynos4412-trats2.dts
@@ -65,7 +65,7 @@
regulator-name = "CAM_SENSOR_A";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
- gpio = <&gpm0 2 0>;
+ gpio = <&gpm0 2 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
@@ -74,7 +74,7 @@
regulator-name = "LCD_VDD_2.2V";
regulator-min-microvolt = <2200000>;
regulator-max-microvolt = <2200000>;
- gpio = <&gpc0 1 0>;
+ gpio = <&gpc0 1 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
@@ -83,7 +83,7 @@
regulator-name = "CAM_AF";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
- gpio = <&gpm0 4 0>;
+ gpio = <&gpm0 4 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
@@ -92,7 +92,7 @@
regulator-name = "LED_A_3.0V";
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
- gpio = <&gpj0 5 0>;
+ gpio = <&gpj0 5 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
};
@@ -101,21 +101,21 @@
compatible = "gpio-keys";
key-down {
- gpios = <&gpx3 3 1>;
+ gpios = <&gpx3 3 GPIO_ACTIVE_LOW>;
linux,code = <114>;
label = "volume down";
debounce-interval = <10>;
};
key-up {
- gpios = <&gpx2 2 1>;
+ gpios = <&gpx2 2 GPIO_ACTIVE_LOW>;
linux,code = <115>;
label = "volume up";
debounce-interval = <10>;
};
key-power {
- gpios = <&gpx2 7 1>;
+ gpios = <&gpx2 7 GPIO_ACTIVE_LOW>;
linux,code = <116>;
label = "power";
debounce-interval = <10>;
@@ -123,7 +123,7 @@
};
key-ok {
- gpios = <&gpx0 1 1>;
+ gpios = <&gpx0 1 GPIO_ACTIVE_LOW>;
linux,code = <139>;
label = "ok";
debounce-inteval = <10>;
@@ -198,7 +198,7 @@
i2c_ak8975: i2c-gpio-0 {
compatible = "i2c-gpio";
- gpios = <&gpy2 4 0>, <&gpy2 5 0>;
+ gpios = <&gpy2 4 GPIO_ACTIVE_HIGH>, <&gpy2 5 GPIO_ACTIVE_HIGH>;
i2c-gpio,delay-us = <2>;
#address-cells = <1>;
#size-cells = <0>;
@@ -207,13 +207,13 @@
ak8975@0c {
compatible = "asahi-kasei,ak8975";
reg = <0x0c>;
- gpios = <&gpj0 7 0>;
+ gpios = <&gpj0 7 GPIO_ACTIVE_HIGH>;
};
};
i2c_cm36651: i2c-gpio-2 {
compatible = "i2c-gpio";
- gpios = <&gpf0 0 1>, <&gpf0 1 1>;
+ gpios = <&gpf0 0 GPIO_ACTIVE_LOW>, <&gpf0 1 GPIO_ACTIVE_LOW>;
i2c-gpio,delay-us = <2>;
#address-cells = <1>;
#size-cells = <0>;
@@ -359,7 +359,7 @@
reg = <0>;
vdd3-supply = <&lcd_vdd3_reg>;
vci-supply = <&ldo25_reg>;
- reset-gpios = <&gpy4 5 0>;
+ reset-gpios = <&gpy4 5 GPIO_ACTIVE_HIGH>;
power-on-delay= <50>;
reset-delay = <100>;
init-delay = <100>;
@@ -446,7 +446,7 @@
clocks = <&camera 1>;
clock-names = "extclk";
samsung,camclk-out = <1>;
- gpios = <&gpm1 6 0>;
+ gpios = <&gpm1 6 GPIO_ACTIVE_HIGH>;
port {
is_s5k6a3_ep: endpoint {
@@ -488,8 +488,8 @@
s5c73m3@3c {
compatible = "samsung,s5c73m3";
reg = <0x3c>;
- standby-gpios = <&gpm0 1 1>; /* ISP_STANDBY */
- xshutdown-gpios = <&gpf1 3 1>; /* ISP_RESET */
+ standby-gpios = <&gpm0 1 GPIO_ACTIVE_LOW>; /* ISP_STANDBY */
+ xshutdown-gpios = <&gpf1 3 GPIO_ACTIVE_LOW>; /* ISP_RESET */
vdd-int-supply = <&buck9_reg>;
vddio-cis-supply = <&ldo9_reg>;
vdda-supply = <&ldo17_reg>;
@@ -1241,7 +1241,7 @@
&sdhci_2 {
bus-width = <4>;
- cd-gpios = <&gpx3 4 0>;
+ cd-gpios = <&gpx3 4 GPIO_ACTIVE_HIGH>;
cd-inverted;
pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4>;
pinctrl-names = "default";
@@ -1268,7 +1268,7 @@
&spi_1 {
pinctrl-names = "default";
pinctrl-0 = <&spi1_bus>;
- cs-gpios = <&gpb 5 0>;
+ cs-gpios = <&gpb 5 GPIO_ACTIVE_HIGH>;
status = "okay";
s5c73m3_spi: s5c73m3 {
--
2.4.3
^ permalink raw reply related [flat|nested] 7+ messages in thread* [PATCH 4/5] ARM: dts: Use GPIO constants for flags cells in exynos5420/5422/5800 boards
2015-10-07 13:14 [PATCH 0/5] ARM: dts: Use GPIO constants for flags cells in exynos boards Javier Martinez Canillas
` (2 preceding siblings ...)
2015-10-07 13:14 ` [PATCH 3/5] ARM: dts: Use GPIO constants for flags cells in exynos4412 boards Javier Martinez Canillas
@ 2015-10-07 13:14 ` Javier Martinez Canillas
2015-10-07 13:14 ` [PATCH 5/5] ARM: dts: Use GPIO constants for flags cells in exynos5440 boards Javier Martinez Canillas
2015-10-07 22:41 ` [PATCH 0/5] ARM: dts: Use GPIO constants for flags cells in exynos boards Kukjin Kim
5 siblings, 0 replies; 7+ messages in thread
From: Javier Martinez Canillas @ 2015-10-07 13:14 UTC (permalink / raw)
To: linux-kernel
Cc: linux-samsung-soc, Kukjin Kim, Krzysztof Kozlowski,
Javier Martinez Canillas
The board DTS are using numeric values instead of the defined GPIO
constanst to express polarity, use them to make the DTS more clear.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
---
arch/arm/boot/dts/exynos5420-arndale-octa.dts | 3 ++-
arch/arm/boot/dts/exynos5420-peach-pit.dts | 8 ++++----
arch/arm/boot/dts/exynos5420-smdk5420.dts | 7 ++++---
arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 4 ++--
arch/arm/boot/dts/exynos5800-peach-pi.dts | 8 ++++----
5 files changed, 16 insertions(+), 14 deletions(-)
diff --git a/arch/arm/boot/dts/exynos5420-arndale-octa.dts b/arch/arm/boot/dts/exynos5420-arndale-octa.dts
index eeb4ac22cfce..4ecef6981d5c 100644
--- a/arch/arm/boot/dts/exynos5420-arndale-octa.dts
+++ b/arch/arm/boot/dts/exynos5420-arndale-octa.dts
@@ -11,6 +11,7 @@
/dts-v1/;
#include "exynos5420.dtsi"
+#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/input/input.h>
#include <dt-bindings/clock/samsung,s2mps11.h>
@@ -44,7 +45,7 @@
wakeup {
label = "SW-TACT1";
- gpios = <&gpx2 7 1>;
+ gpios = <&gpx2 7 GPIO_ACTIVE_LOW>;
linux,code = <KEY_WAKEUP>;
gpio-key,wakeup;
};
diff --git a/arch/arm/boot/dts/exynos5420-peach-pit.dts b/arch/arm/boot/dts/exynos5420-peach-pit.dts
index 8f4d76c5e11c..c53fca8440a1 100644
--- a/arch/arm/boot/dts/exynos5420-peach-pit.dts
+++ b/arch/arm/boot/dts/exynos5420-peach-pit.dts
@@ -94,7 +94,7 @@
regulator-name = "P5.0V_USB3CON0";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
- gpio = <&gph0 0 0>;
+ gpio = <&gph0 0 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&usb300_vbus_en>;
enable-active-high;
@@ -105,7 +105,7 @@
regulator-name = "P5.0V_USB3CON1";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
- gpio = <&gph0 1 0>;
+ gpio = <&gph0 1 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&usb301_vbus_en>;
enable-active-high;
@@ -153,7 +153,7 @@
samsung,color-depth = <1>;
samsung,link-rate = <0x06>;
samsung,lane-count = <2>;
- samsung,hpd-gpio = <&gpx2 6 0>;
+ samsung,hpd-gpio = <&gpx2 6 GPIO_ACTIVE_HIGH>;
ports {
port@0 {
@@ -925,7 +925,7 @@
status = "okay";
num-cs = <1>;
samsung,spi-src-clk = <0>;
- cs-gpios = <&gpb1 2 0>;
+ cs-gpios = <&gpb1 2 GPIO_ACTIVE_HIGH>;
cros_ec: cros-ec@0 {
compatible = "google,cros-ec-spi";
diff --git a/arch/arm/boot/dts/exynos5420-smdk5420.dts b/arch/arm/boot/dts/exynos5420-smdk5420.dts
index 7520d52f4e22..ac35aefd320f 100644
--- a/arch/arm/boot/dts/exynos5420-smdk5420.dts
+++ b/arch/arm/boot/dts/exynos5420-smdk5420.dts
@@ -11,6 +11,7 @@
/dts-v1/;
#include "exynos5420.dtsi"
+#include <dt-bindings/gpio/gpio.h>
/ {
model = "Samsung SMDK5420 board based on EXYNOS5420";
@@ -69,7 +70,7 @@
regulator-name = "VBUS0";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
- gpio = <&gpg0 5 0>;
+ gpio = <&gpg0 5 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&usb300_vbus_en>;
enable-active-high;
@@ -80,7 +81,7 @@
regulator-name = "VBUS1";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
- gpio = <&gpg1 4 0>;
+ gpio = <&gpg1 4 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&usb301_vbus_en>;
enable-active-high;
@@ -121,7 +122,7 @@
&hdmi {
status = "okay";
- hpd-gpio = <&gpx3 7 0>;
+ hpd-gpio = <&gpx3 7 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&hdmi_hpd_irq>;
};
diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi
index a83d569baea8..1af5bdc2bdb1 100644
--- a/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi
+++ b/arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi
@@ -43,7 +43,7 @@
pinctrl-0 = <&emmc_nrst_pin>;
pinctrl-names = "default";
compatible = "mmc-pwrseq-emmc";
- reset-gpios = <&gpd1 0 1>;
+ reset-gpios = <&gpd1 0 GPIO_ACTIVE_LOW>;
};
fan0: pwm-fan {
@@ -74,7 +74,7 @@
&hdmi {
status = "okay";
- hpd-gpio = <&gpx3 7 0>;
+ hpd-gpio = <&gpx3 7 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&hdmi_hpd_irq>;
diff --git a/arch/arm/boot/dts/exynos5800-peach-pi.dts b/arch/arm/boot/dts/exynos5800-peach-pi.dts
index 7d5b386b5ae6..39ecc38aa54f 100644
--- a/arch/arm/boot/dts/exynos5800-peach-pi.dts
+++ b/arch/arm/boot/dts/exynos5800-peach-pi.dts
@@ -94,7 +94,7 @@
regulator-name = "P5.0V_USB3CON0";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
- gpio = <&gph0 0 0>;
+ gpio = <&gph0 0 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&usb300_vbus_en>;
enable-active-high;
@@ -105,7 +105,7 @@
regulator-name = "P5.0V_USB3CON1";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
- gpio = <&gph0 1 0>;
+ gpio = <&gph0 1 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&usb301_vbus_en>;
enable-active-high;
@@ -147,7 +147,7 @@
samsung,color-depth = <1>;
samsung,link-rate = <0x0a>;
samsung,lane-count = <2>;
- samsung,hpd-gpio = <&gpx2 6 0>;
+ samsung,hpd-gpio = <&gpx2 6 GPIO_ACTIVE_HIGH>;
panel = <&panel>;
};
@@ -888,7 +888,7 @@
status = "okay";
num-cs = <1>;
samsung,spi-src-clk = <0>;
- cs-gpios = <&gpb1 2 0>;
+ cs-gpios = <&gpb1 2 GPIO_ACTIVE_HIGH>;
cros_ec: cros-ec@0 {
compatible = "google,cros-ec-spi";
--
2.4.3
^ permalink raw reply related [flat|nested] 7+ messages in thread* [PATCH 5/5] ARM: dts: Use GPIO constants for flags cells in exynos5440 boards
2015-10-07 13:14 [PATCH 0/5] ARM: dts: Use GPIO constants for flags cells in exynos boards Javier Martinez Canillas
` (3 preceding siblings ...)
2015-10-07 13:14 ` [PATCH 4/5] ARM: dts: Use GPIO constants for flags cells in exynos5420/5422/5800 boards Javier Martinez Canillas
@ 2015-10-07 13:14 ` Javier Martinez Canillas
2015-10-07 22:41 ` [PATCH 0/5] ARM: dts: Use GPIO constants for flags cells in exynos boards Kukjin Kim
5 siblings, 0 replies; 7+ messages in thread
From: Javier Martinez Canillas @ 2015-10-07 13:14 UTC (permalink / raw)
To: linux-kernel
Cc: linux-samsung-soc, Kukjin Kim, Krzysztof Kozlowski,
Javier Martinez Canillas
The board DTS are using numeric values instead of the defined GPIO
constanst to express polarity, use them to make the DTS more clear.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
---
arch/arm/boot/dts/exynos5440-ssdk5440.dts | 5 +++--
1 file changed, 3 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/exynos5440-ssdk5440.dts b/arch/arm/boot/dts/exynos5440-ssdk5440.dts
index e4443f4e6572..6a0d802e87c8 100644
--- a/arch/arm/boot/dts/exynos5440-ssdk5440.dts
+++ b/arch/arm/boot/dts/exynos5440-ssdk5440.dts
@@ -11,6 +11,7 @@
/dts-v1/;
#include "exynos5440.dtsi"
+#include <dt-bindings/gpio/gpio.h>
/ {
model = "SAMSUNG SSDK5440 board based on EXYNOS5440";
@@ -29,12 +30,12 @@
};
&pcie_0 {
- reset-gpio = <&pin_ctrl 5 0>;
+ reset-gpio = <&pin_ctrl 5 GPIO_ACTIVE_HIGH>;
status = "okay";
};
&pcie_1 {
- reset-gpio = <&pin_ctrl 22 0>;
+ reset-gpio = <&pin_ctrl 22 GPIO_ACTIVE_HIGH>;
status = "okay";
};
--
2.4.3
^ permalink raw reply related [flat|nested] 7+ messages in thread* Re: [PATCH 0/5] ARM: dts: Use GPIO constants for flags cells in exynos boards
2015-10-07 13:14 [PATCH 0/5] ARM: dts: Use GPIO constants for flags cells in exynos boards Javier Martinez Canillas
` (4 preceding siblings ...)
2015-10-07 13:14 ` [PATCH 5/5] ARM: dts: Use GPIO constants for flags cells in exynos5440 boards Javier Martinez Canillas
@ 2015-10-07 22:41 ` Kukjin Kim
5 siblings, 0 replies; 7+ messages in thread
From: Kukjin Kim @ 2015-10-07 22:41 UTC (permalink / raw)
To: Javier Martinez Canillas
Cc: linux-kernel, linux-samsung-soc, Kukjin Kim, Krzysztof Kozlowski
On 10/07/15 22:14, Javier Martinez Canillas wrote:
> Hello,
>
> This series contains trivial patches that use the GPIO constants
> defined in include/dt-bindings/gpio/gpio.h to express GPIO polarity
> instead of numeric values.
>
> There is no functional change and the compiled dtbs are unchanged but
> is a good practice to use the defined macros instead of magic numbers
> since that makes the DTS more readable.
>
> Since the changes are trivial, I thought that split the changes per
> board DTS would create an unnecessary churn but a single patch would
> maybe be harder to review so I decided that split it by SoC family
> would be a good trade off.
>
> Please let me know if you prefer another approach.
>
> Best regards,
> Javier
>
>
> Javier Martinez Canillas (5):
> ARM: dts: Use GPIO constants for flags cells in exynos3250 boards
> ARM: dts: Use GPIO constants for flags cells in exynos4120 boards
> ARM: dts: Use GPIO constants for flags cells in exynos4412 boards
> ARM: dts: Use GPIO constants for flags cells in exynos5420/5422/5800
> boards
> ARM: dts: Use GPIO constants for flags cells in exynos5440 boards
>
> arch/arm/boot/dts/exynos3250-monk.dts | 8 ++---
> arch/arm/boot/dts/exynos3250-rinato.dts | 10 +++---
> arch/arm/boot/dts/exynos4210-origen.dts | 15 ++++----
> arch/arm/boot/dts/exynos4210-smdkv310.dts | 3 +-
> arch/arm/boot/dts/exynos4210-trats.dts | 29 +++++++--------
> arch/arm/boot/dts/exynos4210-universal_c210.dts | 42 +++++++++++-----------
> arch/arm/boot/dts/exynos4412-odroid-common.dtsi | 15 ++++----
> arch/arm/boot/dts/exynos4412-odroidu3.dts | 2 +-
> arch/arm/boot/dts/exynos4412-odroidx.dts | 8 ++---
> arch/arm/boot/dts/exynos4412-origen.dts | 15 ++++----
> arch/arm/boot/dts/exynos4412-tiny4412.dts | 9 ++---
> arch/arm/boot/dts/exynos4412-trats2.dts | 34 +++++++++---------
> arch/arm/boot/dts/exynos5420-arndale-octa.dts | 3 +-
> arch/arm/boot/dts/exynos5420-peach-pit.dts | 8 ++---
> arch/arm/boot/dts/exynos5420-smdk5420.dts | 7 ++--
> arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi | 4 +--
> arch/arm/boot/dts/exynos5440-ssdk5440.dts | 5 +--
> arch/arm/boot/dts/exynos5800-peach-pi.dts | 8 ++---
> 18 files changed, 118 insertions(+), 107 deletions(-)
>
Applied this whole series, thanks.
- Kukjin
^ permalink raw reply [flat|nested] 7+ messages in thread