Re: [PATCH v3 08/10] clk: ns2: add clock support for Broadcom Northstar 2 SoC

[Scott Branden <sbranden@broadcom.com>]

We need some sort of kconfig option to differentiate NS2 clock driver 
from being pulled in all the time.

On 15-10-15 12:48 PM, Jon Mason wrote:
> The Broadcom Northstar 2 SoC is architected under the iProc
> architecture. It has the following PLLs: GENPLL SCR, GENPLL SW,
> LCPLL DDR, LCPLL Ports, all derived from an onboard crystal.
>
> Signed-off-by: Jon Mason <jonmason@broadcom.com>
> ---
>   drivers/clk/Makefile                |   2 +-
>   drivers/clk/bcm/Makefile            |   1 +
>   drivers/clk/bcm/clk-ns2.c           | 288 ++++++++++++++++++++++++++++++++++++
>   include/dt-bindings/clock/bcm-ns2.h |  72 +++++++++
>   4 files changed, 362 insertions(+), 1 deletion(-)
>   create mode 100644 drivers/clk/bcm/clk-ns2.c
>   create mode 100644 include/dt-bindings/clock/bcm-ns2.h
>
> diff --git a/drivers/clk/Makefile b/drivers/clk/Makefile
> index d08b3e5..6124bd3 100644
> --- a/drivers/clk/Makefile
> +++ b/drivers/clk/Makefile
> @@ -47,7 +47,7 @@ obj-$(CONFIG_COMMON_CLK_WM831X)		+= clk-wm831x.o
>   obj-$(CONFIG_COMMON_CLK_XGENE)		+= clk-xgene.o
>   obj-$(CONFIG_COMMON_CLK_PWM)		+= clk-pwm.o
>   obj-$(CONFIG_COMMON_CLK_AT91)		+= at91/
> -obj-$(CONFIG_ARCH_BCM)			+= bcm/
> +obj-y					+= bcm/
>   obj-$(CONFIG_ARCH_BERLIN)		+= berlin/
>   obj-$(CONFIG_ARCH_HISI)			+= hisilicon/
>   obj-$(CONFIG_ARCH_MXC)			+= imx/
> diff --git a/drivers/clk/bcm/Makefile b/drivers/clk/bcm/Makefile
> index e258b28..2d1cbc5 100644
> --- a/drivers/clk/bcm/Makefile
> +++ b/drivers/clk/bcm/Makefile
> @@ -3,6 +3,7 @@ obj-$(CONFIG_CLK_BCM_KONA)	+= clk-kona-setup.o
>   obj-$(CONFIG_CLK_BCM_KONA)	+= clk-bcm281xx.o
>   obj-$(CONFIG_CLK_BCM_KONA)	+= clk-bcm21664.o
>   obj-$(CONFIG_COMMON_CLK_IPROC)	+= clk-iproc-armpll.o clk-iproc-pll.o clk-iproc-asiu.o
> +obj-$(CONFIG_COMMON_CLK_IPROC)	+= clk-ns2.o

NS2 code is dragged in for all IPROC SoCs.  We need a config option for 
NS2 (CONFIG_ARCH_BCM_NS2) to avoid this (if Arnd allows this for ARMv8 
processors... ?).

You can see below ARMv7 processors don't have this problem.

If not we need to add CONFIG_CLK_NS2.