From: Julian Margetson <runaway@candw.ms>
To: "Måns Rullgård" <mans@mansr.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>,
Andy Shevchenko <andriy.shevchenko@linux.intel.com>,
Tejun Heo <tj@kernel.org>,
linux-ide@vger.kernel.org,
"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>
Subject: Re: [PATCH 1/3] ata: sata_dwc_460ex: use "dmas" DT property to find dma channel
Date: Sat, 19 Dec 2015 16:16:47 -0400 [thread overview]
Message-ID: <5675BB2F.6060107@candw.ms> (raw)
In-Reply-To: <yw1xio3u8dgc.fsf@unicorn.mansr.com>
[-- Attachment #1: Type: text/plain, Size: 4022 bytes --]
On 12/19/2015 3:07 PM, Måns Rullgård wrote:
> Julian Margetson <runaway@candw.ms> writes:
>
>> On 12/19/2015 1:19 PM, Måns Rullgård wrote:
>>> Julian Margetson <runaway@candw.ms> writes:
>>>
>>>> On 12/19/2015 1:05 PM, Måns Rullgård wrote:
>>>>> Andy Shevchenko <andy.shevchenko@gmail.com> writes:
>>>>>
>>>>>> On Sat, Dec 19, 2015 at 5:40 PM, Måns Rullgård <mans@mansr.com> wrote:
>>>>>>
>>>>>>> OK, I've found something. The dma setup errors are benign, caused by
>>>>>>> the driver calling dmaengine_prep_slave_sg() even for non-dma
>>>>>>> operations.
>>>>>> I suppose the following is a quick fix to avoid preparing descriptor
>>>>>> for non-DMA operations (not tested anyhow)
>>>>>>
>>>>>> a/drivers/ata/sata_dwc_460ex.c
>>>>>> +++ b/drivers/ata/sata_dwc_460ex.c
>>>>>> @@ -1041,6 +1041,9 @@ static void sata_dwc_qc_prep_by_tag(struct
>>>>>> ata_queued_cmd *qc, u8 tag)
>>>>>> __func__, ap->port_no, get_dma_dir_descript(qc->dma_dir),
>>>>>> qc->n_elem);
>>>>>>
>>>>>> + if (!is_slave_direction(qc->dma_dir))
>>>>>> + return;
>>>>>> +
>>>>>> desc = dma_dwc_xfer_setup(qc);
>>>>>> if (!desc) {
>>>>>> dev_err(ap->dev, "%s: dma_dwc_xfer_setup returns NULL\n",
>>>>> I already have a better patch sitting here.
>>>>>
>>>>>>> The real error is the lock recursion that's reported
>>>>>>> later. I wasn't seeing it since I was running a UP non-preempt kernel.
>>>>>>> With lock debugging enabled, I get the same error. This patch should
>>>>>>> fix it.
>>>>>>> - spin_lock_irqsave(&ap->host->lock, flags);
>>>>>>> hsdevp->cmd_issued[tag] = cmd_issued;
>>>>>>> - spin_unlock_irqrestore(&ap->host->lock, flags);
>>>>>>> +
>>>>>> This will create a second empty line, though I don't care it is so minor.
>>>>> The patch leaves one blank line before the following block comment. I
>>>>> think it looks better that way.
>>>>>
>>>> Still can't get the patch applied .
>>> Sorry, didn't realise it conflicted with an intervening patch I had in
>>> my tree. Try this one.
>>>
>>
>> =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2015.12.19 14:44:52 =~=~=~=~=~=~=~=~=~=~=~=
>>
>> U-Boot 2015.a (May 16 2015 - 14:20:11)
>>
>> CPU: AMCC PowerPC 460EX Rev. B at 1155 MHz (PLB=231 OPB=115 EBC=115)
>> No Security/Kasumi support
>> Bootstrap Option H - Boot ROM Location I2C (Addr 0x52)
>> Internal PCI arbiter enabled
>> 32 kB I-Cache 32 kB D-Cache
>> Board: Sam460ex/cr, PCIe 4x + SATA-2
>> I2C: ready
>> DRAM: 2 GiB (ECC not enabled, 462 MHz, CL4)
>> PCI: Bus Dev VenId DevId Class Int
>> 00 04 1095 3512 0104 00
>> 00 06 126f 0501 0380 00
>> PCIE1: successfully set as root-complex
>> 02 00 1002 683f 0300 ff
>> Net: ppc_4xx_eth0
>> FPGA: Revision 03 (2010-10-07)
>> SM502: found
>> PERMD2:not found
>> VGA: 1
>> VESA: OK
>> [ 0.000000] Using Canyonlands machine description
>> [ 0.000000] Initializing cgroup subsys cpu
>> [ 0.000000] Linux version 4.4.0-rc5-Sam460ex (root@julian-VirtualBox) (gcc version 4.8.2 (Ubuntu 4.8.2-16ubuntu3) ) #1 PREEMPT Sat Dec 19 14:25:55 AST 2015
>> [ 0.000000] Zone ranges:
>> [ 0.000000] DMA [mem 0x0000000000000000-0x000000002fffffff]
>> [ 0.000000] Normal empty
>> [ 0.000000] HighMem [mem 0x0000000030000000-0x000000007fffffff]
>> [ 0.000000] Movable zone start for each node
>> [ 0.000000] Early memory node ranges
>> [ 0.000000] node 0: [mem 0x0000000000000000-0x000000007fffffff]
>> [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000007fffffff]
>> [ 0.000000] MMU: Allocated 1088 bytes of context maps for 255 contexts
>> [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 522752
>> [ 0.000000] Kernel command line: root=/dev/sda8 console=ttyS0,115200 console=tty1 dw_dmac_core.dyndbg dw_dmac.dyndbg
> Please add ignore_log_level.
>
Had to truncate the kernel command line to add it.
[-- Attachment #2: log5.log.log --]
[-- Type: text/plain, Size: 53525 bytes --]
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2015.12.19 15:59:55 =~=~=~=~=~=~=~=~=~=~=~=
U-Boot 2015.a (May 16 2015 - 14:20:11)
CPU: AMCC PowerPC 460EX Rev. B at 1155 MHz (PLB=231 OPB=115 EBC=115)
No Security/Kasumi support
Bootstrap Option H - Boot ROM Location I2C (Addr 0x52)
Internal PCI arbiter enabled
32 kB I-Cache 32 kB D-Cache
Board: Sam460ex/cr, PCIe 4x + SATA-2
I2C: ready
DRAM: 2 GiB (ECC not enabled, 462 MHz, CL4)
PCI: Bus Dev VenId DevId Class Int
00 04 1095 3512 0104 00
00 06 126f 0501 0380 00
PCIE1: successfully set as root-complex
02 00 1002 683f 0300 ff
Net: ppc_4xx_eth0
FPGA: Revision 03 (2010-10-07)
SM502: found
PERMD2:not found
VGA: 1
VESA: OK
[ 0.000000] Using Canyonlands machine description
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 4.4.0-rc5-Sam460ex (root@julian-VirtualBox) (gcc version 4.8.2 (Ubuntu 4.8.2-16ubuntu3) ) #1 PREEMPT Sat Dec 19 14:25:55 AST 2015
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000000000-0x000000002fffffff]
[ 0.000000] Normal empty
[ 0.000000] HighMem [mem 0x0000000030000000-0x000000007fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000007fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000007fffffff]
[ 0.000000] MMU: Allocated 1088 bytes of context maps for 255 contexts
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 522752
[ 0.000000] Kernel command line: root=/dev/sda8 console=ttyS0,115200 ignore_log_level dw_dmac_core.dyndbg dw_dmac.dyndbg
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Sorting __ex_table...
[ 0.000000] Memory: 2068868K/2097152K available (6732K kernel code, 332K rwdata, 3232K rodata, 236K init, 368K bss, 28284K reserved, 0K cma-reserved, 1310720K highmem)
[ 0.000000] Kernel virtual memory layout:
[ 0.000000] * 0xfffcf000..0xfffff000 : fixmap
[ 0.000000] * 0xffc00000..0xffe00000 : highmem PTEs
[ 0.000000] * 0xffa00000..0xffc00000 : consistent mem
[ 0.000000] * 0xffa00000..0xffa00000 : early ioremap
[ 0.000000] * 0xf1000000..0xffa00000 : vmalloc & ioremap
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 32.
[ 0.000000] NR_IRQS:512 nr_irqs:512 16
[ 0.000000] UIC0 (32 IRQ sources) at DCR 0xc0
[ 0.000000] UIC1 (32 IRQ sources) at DCR 0xd0
[ 0.000000] UIC2 (32 IRQ sources) at DCR 0xe0
[ 0.000000] UIC3 (32 IRQ sources) at DCR 0xf0
[ 0.000013] clocksource: timebase: mask: 0xffffffffffffffff max_cycles: 0x10a60dda894, max_idle_ns: 440795207041 ns
[ 0.000023] clocksource: timebase mult[dda520] shift[24] registered
[ 0.000144] Console: colour dummy device 80x25
[ 0.000175] pid_max: default: 32768 minimum: 301
[ 0.000277] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000289] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.004032] devtmpfs: initialized
[ 0.006766] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[ 0.007154] xor: measuring software checksum speed
[ 0.016351] 8regs : 856.000 MB/sec
[ 0.026358] 8regs_prefetch: 784.000 MB/sec
[ 0.036389] 32regs : 1120.000 MB/sec
[ 0.046422] 32regs_prefetch: 996.000 MB/sec
[ 0.046429] xor: using function: 32regs (1120.000 MB/sec)
[ 0.046463] prandom: seed boundary self test passed
[ 0.048911] prandom: 100 self tests passed
[ 0.049448] NET: Registered protocol family 16
[ 0.052548] cpuidle: using governor ladder
[ 0.055582] cpuidle: using governor menu
[ 0.055982] 256k L2-cache enabled
[ 0.056065] PCIE0: Port disabled via device-tree
[ 0.056116] PCIE1: Checking link...
[ 0.056122] PCIE1: Device detected, waiting for link...
[ 0.056128] PCIE1: link is up !
[ 0.158413] PCI host bridge /plb/pciex@d20000000 (primary) ranges:
[ 0.158440] MEM 0x0000000e80000000..0x0000000effffffff -> 0x0000000080000000
[ 0.158455] MEM 0x0000000f00100000..0x0000000f001fffff -> 0x0000000000000000
[ 0.158465] IO 0x0000000f80010000..0x0000000f8001ffff -> 0x0000000000000000
[ 0.158488] 4xx PCI DMA offset set to 0x00000000
[ 0.158494] 4xx PCI DMA window base to 0x0000000000000000
[ 0.158500] DMA window size 0x0000000080000000
[ 0.158524] PCIE1: successfully set as root-complex
[ 0.158589] PCI host bridge /plb/pci@c0ec00000 (primary) ranges:
[ 0.158604] MEM 0x0000000d80000000..0x0000000dffffffff -> 0x0000000080000000
[ 0.158618] MEM 0x0000000c0ee00000..0x0000000c0eefffff -> 0x0000000000000000
[ 0.158629] IO 0x0000000c08000000..0x0000000c0800ffff -> 0x0000000000000000
[ 0.158643] 4xx PCI DMA offset set to 0x00000000
[ 0.158648] 4xx PCI DMA window base to 0x0000000000000000
[ 0.158654] DMA window size 0x0000000080000000
[ 0.159140] PCI: Probing PCI hardware
[ 0.159241] PCI host bridge to bus 0000:80
[ 0.159259] pci_bus 0000:80: root bus resource [io 0xfffe0000-0xfffeffff] (bus address [0x0000-0xffff])
[ 0.159272] pci_bus 0000:80: root bus resource [mem 0xe80000000-0xeffffffff] (bus address [0x80000000-0xffffffff])
[ 0.159284] pci_bus 0000:80: root bus resource [mem 0xf00100000-0xf001fffff] (bus address [0x00000000-0x000fffff])
[ 0.159297] pci_bus 0000:80: root bus resource [bus 80-ff]
[ 0.159421] PCI: Hiding 4xx host bridge resources 0000:80:00.0
[ 0.160285] pci 0000:80:00.0: PCI bridge to [bus 81-bf]
[ 0.160491] PCI host bridge to bus 0001:00
[ 0.160505] pci_bus 0001:00: root bus resource [io 0x0000-0xffff]
[ 0.160517] pci_bus 0001:00: root bus resource [mem 0xd80000000-0xdffffffff] (bus address [0x80000000-0xffffffff])
[ 0.160529] pci_bus 0001:00: root bus resource [mem 0xc0ee00000-0xc0eefffff] (bus address [0x00000000-0x000fffff])
[ 0.160540] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 0.161162] pci 0000:80:00.0: BAR 9: assigned [mem 0xe80000000-0xe8fffffff 64bit pref]
[ 0.161174] pci 0000:80:00.0: BAR 8: assigned [mem 0xe90000000-0xe900fffff]
[ 0.161185] pci 0000:80:00.0: BAR 7: assigned [io 0xfffe1000-0xfffe1fff]
[ 0.161201] pci 0000:81:00.0: BAR 0: assigned [mem 0xe80000000-0xe8fffffff 64bit pref]
[ 0.161221] pci 0000:81:00.0: BAR 2: assigned [mem 0xe90000000-0xe9003ffff 64bit]
[ 0.161238] pci 0000:81:00.0: BAR 6: assigned [mem 0xe90040000-0xe9005ffff pref]
[ 0.161251] pci 0000:81:00.1: BAR 0: assigned [mem 0xe90060000-0xe90063fff 64bit]
[ 0.161268] pci 0000:81:00.0: BAR 4: assigned [io 0xfffe1000-0xfffe10ff]
[ 0.161281] pci 0000:80:00.0: PCI bridge to [bus 81-bf]
[ 0.161292] pci 0000:80:00.0: bridge window [io 0xfffe1000-0xfffe1fff]
[ 0.161303] pci 0000:80:00.0: bridge window [mem 0xe90000000-0xe900fffff]
[ 0.161314] pci 0000:80:00.0: bridge window [mem 0xe80000000-0xe8fffffff 64bit pref]
[ 0.161392] pci 0001:00:06.0: BAR 0: assigned [mem 0xd80000000-0xd83ffffff]
[ 0.161405] pci 0001:00:06.0: BAR 1: assigned [mem 0xd84000000-0xd841fffff]
[ 0.161417] pci 0001:00:04.0: BAR 6: assigned [mem 0xd84200000-0xd8427ffff pref]
[ 0.161429] pci 0001:00:04.0: BAR 5: assigned [mem 0xd84280000-0xd842801ff]
[ 0.161440] pci 0001:00:04.0: BAR 4: assigned [io 0x1000-0x100f]
[ 0.161452] pci 0001:00:04.0: BAR 0: assigned [io 0x1010-0x1017]
[ 0.161463] pci 0001:00:04.0: BAR 2: assigned [io 0x1018-0x101f]
[ 0.161475] pci 0001:00:04.0: BAR 1: assigned [io 0x1020-0x1023]
[ 0.161487] pci 0001:00:04.0: BAR 3: assigned [io 0x1024-0x1027]
[ 0.188265] raid6: int32x1 gen() 300 MB/s
[ 0.205419] raid6: int32x1 xor() 173 MB/s
[ 0.222445] raid6: int32x2 gen() 433 MB/s
[ 0.239493] raid6: int32x2 xor() 240 MB/s
[ 0.256585] raid6: int32x4 gen() 476 MB/s
[ 0.273663] raid6: int32x4 xor() 267 MB/s
[ 0.290719] raid6: int32x8 gen() 234 MB/s
[ 0.307892] raid6: int32x8 xor() 218 MB/s
[ 0.307898] raid6: using algorithm int32x4 gen() 476 MB/s
[ 0.307904] raid6: .... xor() 267 MB/s, rmw enabled
[ 0.307911] raid6: using intx1 recovery algorithm
[ 0.308209] vgaarb: device added: PCI:0000:81:00.0,decodes=io+mem,owns=none,locks=none
[ 0.308223] vgaarb: loaded
[ 0.308228] vgaarb: bridge control possible 0000:81:00.0
[ 0.308493] SCSI subsystem initialized
[ 0.308867] usbcore: registered new interface driver usbfs
[ 0.308911] usbcore: registered new interface driver hub
[ 0.308964] usbcore: registered new device driver usb
[ 0.309060] pps_core: LinuxPPS API ver. 1 registered
[ 0.309068] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.309096] PTP clock support registered
[ 0.309240] EDAC MC: Ver: 3.0.0
[ 0.309589] Advanced Linux Sound Architecture Driver Initialized.
[ 0.329521] DMA-API: preallocated 65536 debug entries
[ 0.329534] DMA-API: debugging enabled by kernel config
[ 0.329580] clocksource: Switched to clocksource timebase
[ 0.336185] NET: Registered protocol family 2
[ 0.336769] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.336863] TCP bind hash table entries: 8192 (order: 5, 163840 bytes)
[ 0.337204] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.337315] UDP hash table entries: 512 (order: 2, 24576 bytes)
[ 0.337380] UDP-Lite hash table entries: 512 (order: 2, 24576 bytes)
[ 0.337725] NET: Registered protocol family 1
[ 0.338039] RPC: Registered named UNIX socket transport module.
[ 0.338048] RPC: Registered udp transport module.
[ 0.338054] RPC: Registered tcp transport module.
[ 0.338060] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.338817] Could not remap bcsr
[ 0.341969] genirq: Setting trigger mode 3 for irq 45 failed (uic_set_irq_type+0x0/0x160)
[ 0.345025] futex hash table entries: 256 (order: 0, 7168 bytes)
[ 0.355166] ntfs: driver 2.1.32 [Flags: R/W].
[ 0.355700] fuse init (API version 7.23)
[ 0.359889] async_tx: api initialized (async)
[ 0.359989] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.360006] io scheduler noop registered
[ 0.360148] io scheduler cfq registered (default)
[ 0.362207] crc32: CRC_LE_BITS = 64, CRC_BE BITS = 64
[ 0.362217] crc32: self tests passed, processed 225944 bytes in 892377 nsec
[ 0.363191] crc32c: CRC_LE_BITS = 64
[ 0.363200] crc32c: self tests passed, processed 225944 bytes in 446237 nsec
[ 0.429593] crc32_combine: 8373 self tests passed
[ 0.496188] crc32c_combine: 8373 self tests passed
[ 0.496240] glob: 64 self-tests passed, 0 failed
[ 0.534469] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.535260] console [ttyS0] disabled
[ 0.555405] serial8250.0: ttyS0 at MMIO 0x4ef600300 (irq = 22, base_baud = 691200) is a U6_16550A
[ 1.487085] console [ttyS0] enabled
[ 1.511191] serial8250.0: ttyS1 at MMIO 0x4ef600400 (irq = 23, base_baud = 691200) is a U6_16550A
[ 1.521036] console [ttyS0] disabled
[ 0.000000] Using Canyonlands machine description
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 4.4.0-rc5-Sam460ex (root@julian-VirtualBox) (gcc version 4.8.2 (Ubuntu 4.8.2-16ubuntu3) ) #1 PREEMPT Sat Dec 19 14:25:55 AST 2015
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000000000-0x000000002fffffff]
[ 0.000000] Normal empty
[ 0.000000] HighMem [mem 0x0000000030000000-0x000000007fffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x000000007fffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000007fffffff]
[ 0.000000] MMU: Allocated 1088 bytes of context maps for 255 contexts
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 522752
[ 0.000000] Kernel command line: root=/dev/sda8 console=ttyS0,115200 ignore_log_level dw_dmac_core.dyndbg dw_dmac.dyndbg
[ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Sorting __ex_table...
[ 0.000000] Memory: 2068868K/2097152K available (6732K kernel code, 332K rwdata, 3232K rodata, 236K init, 368K bss, 28284K reserved, 0K cma-reserved, 1310720K highmem)
[ 0.000000] Kernel virtual memory layout:
[ 0.000000] * 0xfffcf000..0xfffff000 : fixmap
[ 0.000000] * 0xffc00000..0xffe00000 : highmem PTEs
[ 0.000000] * 0xffa00000..0xffc00000 : consistent mem
[ 0.000000] * 0xffa00000..0xffa00000 : early ioremap
[ 0.000000] * 0xf1000000..0xffa00000 : vmalloc & ioremap
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 32.
[ 0.000000] NR_IRQS:512 nr_irqs:512 16
[ 0.000000] UIC0 (32 IRQ sources) at DCR 0xc0
[ 0.000000] UIC1 (32 IRQ sources) at DCR 0xd0
[ 0.000000] UIC2 (32 IRQ sources) at DCR 0xe0
[ 0.000000] UIC3 (32 IRQ sources) at DCR 0xf0
[ 0.000013] clocksource: timebase: mask: 0xffffffffffffffff max_cycles: 0x10a60dda894, max_idle_ns: 440795207041 ns
[ 0.000023] clocksource: timebase mult[dda520] shift[24] registered
[ 0.000144] Console: colour dummy device 80x25
[ 0.000175] pid_max: default: 32768 minimum: 301
[ 0.000277] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000289] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.004032] devtmpfs: initialized
[ 0.006766] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 1911260446275000 ns
[ 0.007154] xor: measuring software checksum speed
[ 0.016351] 8regs : 856.000 MB/sec
[ 0.026358] 8regs_prefetch: 784.000 MB/sec
[ 0.036389] 32regs : 1120.000 MB/sec
[ 0.046422] 32regs_prefetch: 996.000 MB/sec
[ 0.046429] xor: using function: 32regs (1120.000 MB/sec)
[ 0.046463] prandom: seed boundary self test passed
[ 0.048911] prandom: 100 self tests passed
[ 0.049448] NET: Registered protocol family 16
[ 0.052548] cpuidle: using governor ladder
[ 0.055582] cpuidle: using governor menu
[ 0.055982] 256k L2-cache enabled
[ 0.056065] PCIE0: Port disabled via device-tree
[ 0.056116] PCIE1: Checking link...
[ 0.056122] PCIE1: Device detected, waiting for link...
[ 0.056128] PCIE1: link is up !
[ 0.158413] PCI host bridge /plb/pciex@d20000000 (primary) ranges:
[ 0.158440] MEM 0x0000000e80000000..0x0000000effffffff -> 0x0000000080000000
[ 0.158455] MEM 0x0000000f00100000..0x0000000f001fffff -> 0x0000000000000000
[ 0.158465] IO 0x0000000f80010000..0x0000000f8001ffff -> 0x0000000000000000
[ 0.158488] 4xx PCI DMA offset set to 0x00000000
[ 0.158494] 4xx PCI DMA window base to 0x0000000000000000
[ 0.158500] DMA window size 0x0000000080000000
[ 0.158524] PCIE1: successfully set as root-complex
[ 0.158589] PCI host bridge /plb/pci@c0ec00000 (primary) ranges:
[ 0.158604] MEM 0x0000000d80000000..0x0000000dffffffff -> 0x0000000080000000
[ 0.158618] MEM 0x0000000c0ee00000..0x0000000c0eefffff -> 0x0000000000000000
[ 0.158629] IO 0x0000000c08000000..0x0000000c0800ffff -> 0x0000000000000000
[ 0.158643] 4xx PCI DMA offset set to 0x00000000
[ 0.158648] 4xx PCI DMA window base to 0x0000000000000000
[ 0.158654] DMA window size 0x0000000080000000
[ 0.159140] PCI: Probing PCI hardware
[ 0.159241] PCI host bridge to bus 0000:80
[ 0.159259] pci_bus 0000:80: root bus resource [io 0xfffe0000-0xfffeffff] (bus address [0x0000-0xffff])
[ 0.159272] pci_bus 0000:80: root bus resource [mem 0xe80000000-0xeffffffff] (bus address [0x80000000-0xffffffff])
[ 0.159284] pci_bus 0000:80: root bus resource [mem 0xf00100000-0xf001fffff] (bus address [0x00000000-0x000fffff])
[ 0.159297] pci_bus 0000:80: root bus resource [bus 80-ff]
[ 0.159421] PCI: Hiding 4xx host bridge resources 0000:80:00.0
[ 0.160285] pci 0000:80:00.0: PCI bridge to [bus 81-bf]
[ 0.160491] PCI host bridge to bus 0001:00
[ 0.160505] pci_bus 0001:00: root bus resource [io 0x0000-0xffff]
[ 0.160517] pci_bus 0001:00: root bus resource [mem 0xd80000000-0xdffffffff] (bus address [0x80000000-0xffffffff])
[ 0.160529] pci_bus 0001:00: root bus resource [mem 0xc0ee00000-0xc0eefffff] (bus address [0x00000000-0x000fffff])
[ 0.160540] pci_bus 0001:00: root bus resource [bus 00-ff]
[ 0.161162] pci 0000:80:00.0: BAR 9: assigned [mem 0xe80000000-0xe8fffffff 64bit pref]
[ 0.161174] pci 0000:80:00.0: BAR 8: assigned [mem 0xe90000000-0xe900fffff]
[ 0.161185] pci 0000:80:00.0: BAR 7: assigned [io 0xfffe1000-0xfffe1fff]
[ 0.161201] pci 0000:81:00.0: BAR 0: assigned [mem 0xe80000000-0xe8fffffff 64bit pref]
[ 0.161221] pci 0000:81:00.0: BAR 2: assigned [mem 0xe90000000-0xe9003ffff 64bit]
[ 0.161238] pci 0000:81:00.0: BAR 6: assigned [mem 0xe90040000-0xe9005ffff pref]
[ 0.161251] pci 0000:81:00.1: BAR 0: assigned [mem 0xe90060000-0xe90063fff 64bit]
[ 0.161268] pci 0000:81:00.0: BAR 4: assigned [io 0xfffe1000-0xfffe10ff]
[ 0.161281] pci 0000:80:00.0: PCI bridge to [bus 81-bf]
[ 0.161292] pci 0000:80:00.0: bridge window [io 0xfffe1000-0xfffe1fff]
[ 0.161303] pci 0000:80:00.0: bridge window [mem 0xe90000000-0xe900fffff]
[ 0.161314] pci 0000:80:00.0: bridge window [mem 0xe80000000-0xe8fffffff 64bit pref]
[ 0.161392] pci 0001:00:06.0: BAR 0: assigned [mem 0xd80000000-0xd83ffffff]
[ 0.161405] pci 0001:00:06.0: BAR 1: assigned [mem 0xd84000000-0xd841fffff]
[ 0.161417] pci 0001:00:04.0: BAR 6: assigned [mem 0xd84200000-0xd8427ffff pref]
[ 0.161429] pci 0001:00:04.0: BAR 5: assigned [mem 0xd84280000-0xd842801ff]
[ 0.161440] pci 0001:00:04.0: BAR 4: assigned [io 0x1000-0x100f]
[ 0.161452] pci 0001:00:04.0: BAR 0: assigned [io 0x1010-0x1017]
[ 0.161463] pci 0001:00:04.0: BAR 2: assigned [io 0x1018-0x101f]
[ 0.161475] pci 0001:00:04.0: BAR 1: assigned [io 0x1020-0x1023]
[ 0.161487] pci 0001:00:04.0: BAR 3: assigned [io 0x1024-0x1027]
[ 0.188265] raid6: int32x1 gen() 300 MB/s
[ 0.205419] raid6: int32x1 xor() 173 MB/s
[ 0.222445] raid6: int32x2 gen() 433 MB/s
[ 0.239493] raid6: int32x2 xor() 240 MB/s
[ 0.256585] raid6: int32x4 gen() 476 MB/s
[ 0.273663] raid6: int32x4 xor() 267 MB/s
[ 0.290719] raid6: int32x8 gen() 234 MB/s
[ 0.307892] raid6: int32x8 xor() 218 MB/s
[ 0.307898] raid6: using algorithm int32x4 gen() 476 MB/s
[ 0.307904] raid6: .... xor() 267 MB/s, rmw enabled
[ 0.307911] raid6: using intx1 recovery algorithm
[ 0.308209] vgaarb: device added: PCI:0000:81:00.0,decodes=io+mem,owns=none,locks=none
[ 0.308223] vgaarb: loaded
[ 0.308228] vgaarb: bridge control possible 0000:81:00.0
[ 0.308493] SCSI subsystem initialized
[ 0.308867] usbcore: registered new interface driver usbfs
[ 0.308911] usbcore: registered new interface driver hub
[ 0.308964] usbcore: registered new device driver usb
[ 0.309060] pps_core: LinuxPPS API ver. 1 registered
[ 0.309068] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.309096] PTP clock support registered
[ 0.309240] EDAC MC: Ver: 3.0.0
[ 0.309589] Advanced Linux Sound Architecture Driver Initialized.
[ 0.329521] DMA-API: preallocated 65536 debug entries
[ 0.329534] DMA-API: debugging enabled by kernel config
[ 0.329580] clocksource: Switched to clocksource timebase
[ 0.336185] NET: Registered protocol family 2
[ 0.336769] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.336863] TCP bind hash table entries: 8192 (order: 5, 163840 bytes)
[ 0.337204] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.337315] UDP hash table entries: 512 (order: 2, 24576 bytes)
[ 0.337380] UDP-Lite hash table entries: 512 (order: 2, 24576 bytes)
[ 0.337725] NET: Registered protocol family 1
[ 0.338039] RPC: Registered named UNIX socket transport module.
[ 0.338048] RPC: Registered udp transport module.
[ 0.338054] RPC: Registered tcp transport module.
[ 0.338060] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.338817] Could not remap bcsr
[ 0.341969] genirq: Setting trigger mode 3 for irq 45 failed (uic_set_irq_type+0x0/0x160)
[ 0.345025] futex hash table entries: 256 (order: 0, 7168 bytes)
[ 0.355166] ntfs: driver 2.1.32 [Flags: R/W].
[ 0.355700] fuse init (API version 7.23)
[ 0.359889] async_tx: api initialized (async)
[ 0.359989] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.360006] io scheduler noop registered
[ 0.360148] io scheduler cfq registered (default)
[ 0.362207] crc32: CRC_LE_BITS = 64, CRC_BE BITS = 64
[ 0.362217] crc32: self tests passed, processed 225944 bytes in 892377 nsec
[ 0.363191] crc32c: CRC_LE_BITS = 64
[ 0.363200] crc32c: self tests passed, processed 225944 bytes in 446237 nsec
[ 0.429593] crc32_combine: 8373 self tests passed
[ 0.496188] crc32c_combine: 8373 self tests passed
[ 0.496240] glob: 64 self-tests passed, 0 failed
[ 0.534469] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.535260] console [ttyS0] disabled
[ 0.555405] serial8250.0: ttyS0 at MMIO 0x4ef600300 (irq = 22, base_baud = 691200) is a U6_16550A
[ 1.487085] console [ttyS0] enabled
[ 1.511191] serial8250.0: ttyS1 at MMIO 0x4ef600400 (irq = 23, base_baud = 691200) is a U6_16550A
[ 1.521036] console [ttyS0] disabled
[ 1.524695] 4ef600300.serial: ttyS0 at MMIO 0x4ef600300 (irq = 22, base_baud = 691200) is a 16550
[ 2.481174] console [ttyS0] enabled
[ 2.485294] 4ef600400.serial: ttyS1 at MMIO 0x4ef600400 (irq = 23, base_baud = 691200) is a 16550
[ 2.494676] Generic non-volatile memory driver v1.1
[ 2.499834] [drm] Initialized drm 1.1.0 20060810
[ 2.504522] [drm] radeon kernel modesetting enabled.
[ 2.510206] [drm] initializing kernel modesetting (VERDE 0x1002:0x683F 0x1545:0x7750).
[ 2.518194] [drm] register mmio base: 0xe90000000
[ 2.522930] [drm] register mmio size: 262144
[ 2.859029] ATOM BIOS: C44501
[ 2.862259] radeon 0000:81:00.0: VRAM: 1024M 0x0000000000000000 - 0x000000003FFFFFFF (1024M used)
[ 2.871169] radeon 0000:81:00.0: GTT: 2048M 0x0000000040000000 - 0x00000000BFFFFFFF
[ 2.878834] [drm] Detected VRAM RAM=1024M, BAR=256M
[ 2.883720] [drm] RAM width 128bits DDR
[ 2.887755] [TTM] Zone kernel: Available graphics memory: 379074 kiB
[ 2.894229] [TTM] Zone highmem: Available graphics memory: 1034434 kiB
[ 2.900760] [TTM] Initializing pool allocator
[ 2.905216] [drm] radeon: 1024M of VRAM memory ready
[ 2.910200] [drm] radeon: 2048M of GTT memory ready.
[ 2.915234] [drm] Loading verde Microcode
[ 2.919284] [drm] Internal thermal controller with fan control
[ 2.925353] [drm] probing gen 2 caps for device aaa1:bed1 = 18cc41/0
[ 2.978966] [drm] radeon: dpm initialized
[ 2.983195] radeon 0000:81:00.0: Direct firmware load for radeon/TAHITI_vce.bin failed with error -2
[ 2.992385] radeon 0000:81:00.0: radeon_vce: Can't load firmware "radeon/TAHITI_vce.bin"
[ 3.000535] [drm] GART: num cpu pages 524288, num gpu pages 524288
[ 3.017262] [drm] probing gen 2 caps for device aaa1:bed1 = 18cc41/0
[ 3.072039] [drm] PCIE GART of 2048M enabled (table at 0x0000000000277000).
[ 3.079320] radeon 0000:81:00.0: WB enabled
[ 3.083555] radeon 0000:81:00.0: fence driver on ring 0 use gpu addr 0x0000000040000c00 and cpu addr 0xedccec00
[ 3.093656] radeon 0000:81:00.0: fence driver on ring 1 use gpu addr 0x0000000040000c04 and cpu addr 0xedccec04
[ 3.103751] radeon 0000:81:00.0: fence driver on ring 2 use gpu addr 0x0000000040000c08 and cpu addr 0xedccec08
[ 3.113846] radeon 0000:81:00.0: fence driver on ring 3 use gpu addr 0x0000000040000c0c and cpu addr 0xedccec0c
[ 3.123941] radeon 0000:81:00.0: fence driver on ring 4 use gpu addr 0x0000000040000c10 and cpu addr 0xedccec10
[ 3.164520] radeon 0000:81:00.0: fence driver on ring 5 use gpu addr 0x0000000000075a18 and cpu addr 0xf5135a18
[ 3.174619] radeon 0000:81:00.0: VCE init error (-22).
[ 3.179768] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 3.186384] [drm] Driver supports precise vblank timestamp query.
[ 3.192490] radeon 0000:81:00.0: radeon: MSI limited to 32-bit
[ 3.198403] genirq: Setting trigger mode 3 for irq 45 failed (uic_set_irq_type+0x0/0x160)
[ 3.206668] radeon 0000:81:00.0: radeon: using MSI.
[ 3.211618] [drm] radeon: irq initialized.
[ 3.971625] [drm:r600_ring_test] *ERROR* radeon: ring 0 test failed (scratch(0x850C)=0xCAFEDEAD)
[ 3.980432] radeon 0000:81:00.0: disabling GPU acceleration
[ 4.189393] [drm] Radeon Display Connectors
[ 4.193648] [drm] Connector 0:
[ 4.196742] [drm] HDMI-A-1
[ 4.199638] [drm] HPD4
[ 4.202178] [drm] DDC: 0x6570 0x6570 0x6574 0x6574 0x6578 0x6578 0x657c 0x657c
[ 4.209579] [drm] Encoders:
[ 4.212556] [drm] DFP1: INTERNAL_UNIPHY2
[ 4.216836] [drm] Connector 1:
[ 4.219899] [drm] DVI-I-1
[ 4.222702] [drm] HPD2
[ 4.225241] [drm] DDC: 0x6560 0x6560 0x6564 0x6564 0x6568 0x6568 0x656c 0x656c
[ 4.232641] [drm] Encoders:
[ 4.235612] [drm] DFP2: INTERNAL_UNIPHY
[ 4.239804] [drm] CRT1: INTERNAL_KLDSCP_DAC1
[ 4.358055] [drm] fb mappable at 0x80678000
[ 4.362253] [drm] vram apper at 0x80000000
[ 4.366358] [drm] size 8294400
[ 4.369422] [drm] fb depth is 24
[ 4.372660] [drm] pitch is 7680
[ 4.651943] Console: switching to colour frame buffer device 240x67
[ 4.730862] radeon 0000:81:00.0: fb0: radeondrmfb frame buffer device
[ 4.739645] [drm] Initialized radeon 2.43.0 20080528 for 0000:81:00.0 on minor 0
[ 4.756405] brd: module loaded
[ 4.763940] loop: module loaded
[ 4.767432] sata_sil 0001:00:04.0: Applying R_ERR on DMA activate FIS errata fix
[ 4.775448] scsi host0: sata_sil
[ 4.779018] scsi host1: sata_sil
[ 4.782403] ata1: SATA max UDMA/100 mmio m512@0xd84280000 tf 0xd84280080 irq 21
[ 4.789730] ata2: SATA max UDMA/100 mmio m512@0xd84280000 tf 0xd842800c0 irq 21
[ 4.797687] PPC 4xx OCP EMAC driver, version 3.54
[ 4.802957] MAL v2 /plb/mcmal, 2 TX channels, 16 RX channels
[ 4.808829] ZMII /plb/opb/emac-zmii@ef600d00 initialized
[ 4.814261] RGMII /plb/opb/emac-rgmii@ef601500 initialized with MDIO support
[ 4.821419] TAH /plb/opb/emac-tah@ef601350 initialized
[ 4.826620] TAH /plb/opb/emac-tah@ef601450 initialized
[ 4.832028] /plb/opb/emac-rgmii@ef601500: input 0 in RGMII mode
[ 4.839156] eth0: EMAC-0 /plb/opb/ethernet@ef600e00, MAC 00:50:c2:80:d5:c5
[ 4.846052] eth0: found Generic MII PHY (0x00)
[ 4.850690] /plb/opb/emac-rgmii@ef601500: input 1 in RGMII mode
[ 4.857796] eth1: EMAC-1 /plb/opb/ethernet@ef600f00, MAC 00:00:00:00:00:00
[ 4.864694] eth1: found Generic MII PHY (0x01)
[ 4.869194] PPP generic driver version 2.4.2
[ 4.873666] PPP BSD Compression module registered
[ 4.878395] PPP Deflate Compression module registered
[ 4.883457] NET: Registered protocol family 24
[ 4.888087] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 4.894780] ppc-of-ehci 4bffd0400.ehci: OF EHCI
[ 4.899489] ppc-of-ehci 4bffd0400.ehci: new USB bus registered, assigned bus number 1
[ 4.908098] ppc-of-ehci 4bffd0400.ehci: irq 31, io mem 0x4bffd0400
[ 4.919596] ppc-of-ehci 4bffd0400.ehci: USB 2.0 started, EHCI 1.00
[ 4.925980] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 4.932787] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 4.940016] usb usb1: Product: OF EHCI
[ 4.943774] usb usb1: Manufacturer: Linux 4.4.0-rc5-Sam460ex ehci_hcd
[ 4.950223] usb usb1: SerialNumber: PPC-OF USB
[ 4.955077] hub 1-0:1.0: USB hub found
[ 4.958893] hub 1-0:1.0: 1 port detected
[ 4.963122] ehci-pci: EHCI PCI platform driver
[ 4.967675] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 4.973990] ppc-of-ohci 4bffd0000.usb: OF OHCI
[ 4.978647] ppc-of-ohci 4bffd0000.usb: new USB bus registered, assigned bus number 2
[ 4.986447] ppc-of-ohci 4bffd0000.usb: irq 32, io mem 0x4bffd0000
[ 5.111605] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 5.152366] ata1.00: ATA-8: WDC WD5000AAKS-00V1A0, 05.01D05, max UDMA/133
[ 5.166582] ata1.00: 976773168 sectors, multi 0: LBA48 NCQ (depth 0/32)
[ 5.183854] ata1.00: configured for UDMA/100
[ 5.206848] scsi 0:0:0:0: Direct-Access ATA WDC WD5000AAKS-0 1D05 PQ: 0 ANSI: 5
[ 5.220252] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 5.228697] sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[ 5.239823] sd 0:0:0:0: [sda] Write Protect is off
[ 5.249681] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.265591] usb 1-1: new high-speed USB device number 2 using ppc-of-ehci
[ 5.284427] sda: RDSK (512) sda1 (DOS^G)(res 2 spb 1) sda2 (SFS^@)(res 2 spb 1) sda3 (SFS^@)(res 2 spb 1) sda4 (SFS^@)(res 2 spb 1) sda5 (SFS^@)(res 2 spb 1) sda6 (SFS^@)(res 2 spb 1) sda7 (NTFS)(res 2 spb 2) sda8 (EXT^C)(res 2 spb 1)
[ 5.326820] sd 0:0:0:0: [sda] Attached SCSI disk
[ 5.394945] usb 1-1: New USB device found, idVendor=0424, idProduct=2517
[ 5.407584] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 5.423680] hub 1-1:1.0: USB hub found
[ 5.430680] hub 1-1:1.0: 7 ports detected
[ 5.547608] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 5.576718] ata2.00: ATAPI: ASUS DRW-24B3ST i, 1.00, max UDMA/100
[ 5.609699] ata2.00: configured for UDMA/100
[ 5.625517] scsi 1:0:0:0: CD-ROM ASUS DRW-24B3ST i 1.00 PQ: 0 ANSI: 5
[ 5.668878] sr 1:0:0:0: [sr0] scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[ 5.683583] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 5.695388] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 5.704861] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 5.711919] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 5.719186] usb 1-1.1: new high-speed USB device number 3 using ppc-of-ehci
[ 5.726158] usb usb2: Product: OF OHCI
[ 5.729925] usb usb2: Manufacturer: Linux 4.4.0-rc5-Sam460ex ohci_hcd
[ 5.736432] usb usb2: SerialNumber: PPC-OF USB
[ 5.741400] hub 2-0:1.0: USB hub found
[ 5.745219] hub 2-0:1.0: 1 port detected
[ 5.749482] ohci-pci: OHCI PCI platform driver
[ 5.754227] usbcore: registered new interface driver usblp
[ 5.759874] usbcore: registered new interface driver usb-storage
[ 5.766108] usbcore: registered new interface driver usbserial
[ 5.772035] usbcore: registered new interface driver usbserial_generic
[ 5.778625] usbserial: USB Serial support registered for generic
[ 5.784961] mousedev: PS/2 mouse device common for all mice
[ 5.790655] i2c /dev entries driver
[ 5.796536] rtc-m41t80 8-0068: rtc core: registered m41t80 as rtc0
[ 5.803706] ibm-iic 4ef600700.i2c: using standard (100 kHz) mode
[ 5.809967] ibm-iic 4ef600800.i2c: using standard (100 kHz) mode
[ 5.816065] md: linear personality registered for level -1
[ 5.821578] md: raid0 personality registered for level 0
[ 5.826953] md: raid1 personality registered for level 1
[ 5.832338] md: raid10 personality registered for level 10
[ 5.838046] md: raid6 personality registered for level 6
[ 5.843408] md: raid5 personality registered for level 5
[ 5.848737] md: raid4 personality registered for level 4
[ 5.854675] usb 1-1.1: New USB device found, idVendor=1a40, idProduct=0101
[ 5.861749] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
[ 5.870236] usb 1-1.1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 5.877610] EDAC PPC4xx MC: v1.0.0
[ 5.881056] usb 1-1.1: Product: USB 2.0 Hub
[ 5.885258] EDAC PPC4xx MC: Reporting type: interrupt
[ 5.890901] hub 1-1.1:1.0: USB hub found
[ 5.894940] hidraw: raw HID events driver (C) Jiri Kosina
[ 5.900674] hub 1-1.1:1.0: 4 ports detected
[ 5.905185] usbcore: registered new interface driver usbhid
[ 5.910834] usbhid: USB HID core driver
[ 5.915341] usbcore: registered new interface driver snd-usb-audio
[ 5.921731] usbcore: registered new interface driver snd-ua101
[ 5.927843] usbcore: registered new interface driver snd-usb-usx2y
[ 5.934407] ipip: IPv4 over IPv4 tunneling driver
[ 5.939646] Initializing XFRM netlink socket
[ 5.944809] NET: Registered protocol family 10
[ 5.950263] sit: IPv6 over IPv4 tunneling driver
[ 5.955402] NET: Registered protocol family 17
[ 5.959950] NET: Registered protocol family 15
[ 5.966421] Key type encrypted registered
[ 5.972009] rtc-m41t80 8-0068: setting system clock to 2015-12-19 16:06:54 UTC (1450541214)
[ 5.980625] ALSA device list:
[ 5.983625] No soundcards found.
[ 5.987635] md: Waiting for all devices to be available before autodetect
[ 5.994463] md: If you don't use raid, use raid=noautodetect
[ 6.000794] md: Autodetecting RAID arrays.
[ 6.004927] md: Scanned 0 and added 0 devices.
[ 6.009379] md: autorun ...
[ 6.012183] md: ... autorun DONE.
[ 6.015612] usb 1-1.2: new low-speed USB device number 4 using ppc-of-ehci
[ 6.047473] EXT4-fs (sda8): mounting ext3 file system using the ext4 subsystem
[ 6.081467] EXT4-fs (sda8): mounted filesystem with ordered data mode. Opts: (null)
[ 6.089223] VFS: Mounted root (ext3 filesystem) readonly on device 8:8.
[ 6.116407] usb 1-1.2: New USB device found, idVendor=04f2, idProduct=0116
[ 6.123456] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 6.130926] usb 1-1.2: Product: USB Keyboard
[ 6.135247] usb 1-1.2: Manufacturer: CHICONY
[ 6.139715] devtmpfs: mounted
[ 6.143527] Freeing unused kernel memory: 236K (c09be000 - c09f9000)
[ 6.156461] input: CHICONY USB Keyboard as /devices/platform/plb/4bffd0400.ehci/usb1/1-1/1-1.2/1-1.2:1.0/0003:04F2:0116.0001/input/input0
[ 6.220061] hid-generic 0003:04F2:0116.0001: input,hidraw0: USB HID v1.10 Keyboard [CHICONY USB Keyboard] on usb-PPC-OF USB-1.2/input0
[ 6.232359] usb 1-1.1.1: new full-speed USB device number 5 using ppc-of-ehci
[ 6.325782] usb 1-1.1.1: New USB device found, idVendor=0d8c, idProduct=000c
[ 6.332879] usb 1-1.1.1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 6.340745] usb 1-1.1.1: Product: C-Media USB Audio Device
[ 6.370063] input: C-Media USB Audio Device as /devices/platform/plb/4bffd0400.ehci/usb1/1-1/1-1.1/1-1.1.1/1-1.1.1:1.3/0003:0D8C:000C.0002/input/input1
[ 6.397609] usb 1-1.6: new full-speed USB device number 6 using ppc-of-ehci
[ 6.434891] hid-generic 0003:0D8C:000C.0002: input,hidraw1: USB HID v1.00 Device [C-Media USB Audio Device ] on usb-PPC-OF USB-1.1.1/input3
[ 6.493278] usb 1-1.6: New USB device found, idVendor=046d, idProduct=c52b
[ 6.500693] usb 1-1.6: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 6.508405] usb 1-1.6: Product: USB Receiver
[ 6.512956] usb 1-1.6: Manufacturer: Logitech
[ 6.522084] input: Logitech USB Receiver as /devices/platform/plb/4bffd0400.ehci/usb1/1-1/1-1.6/1-1.6:1.0/0003:046D:C52B.0003/input/input2
[ 6.585896] hid-generic 0003:046D:C52B.0003: input,hidraw2: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-PPC-OF USB-1.6/input0
[ 6.598174] random: nonblocking pool is initialized
[ 6.609505] input: Logitech USB Receiver as /devices/platform/plb/4bffd0400.ehci/usb1/1-1/1-1.6/1-1.6:1.1/0003:046D:C52B.0004/input/input3
[ 6.672996] hid-generic 0003:046D:C52B.0004: input,hidraw3: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-PPC-OF USB-1.6/input1
[ 6.690714] hid-generic 0003:046D:C52B.0005: hidraw4: USB HID v1.11 Device [Logitech USB Receiver] on usb-PPC-OF USB-1.6/input2
[ 6.775607] usb 1-1.7: new high-speed USB device number 7 using ppc-of-ehci
[ 6.875265] usb 1-1.7: New USB device found, idVendor=0424, idProduct=2240
[ 6.882558] usb 1-1.7: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 6.890159] usb 1-1.7: Product: Ultra Fast Media
[ 6.895002] usb 1-1.7: Manufacturer: Generic
[ 6.899314] usb 1-1.7: SerialNumber: 000000225001
[ 6.906743] usb-storage 1-1.7:1.0: USB Mass Storage device detected
[ 6.913312] scsi host2: usb-storage 1-1.7:1.0
[ 7.294300] systemd[1]: Failed to insert module 'kdbus': Function not implemented
[ 7.388418] systemd[1]: systemd 228 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ -LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN)
[ 7.406999] systemd[1]: Detected architecture ppc.
Welcome to Ubuntu 16.04!
[ 7.444895] systemd[1]: Set hostname to <Sam460ex>.
[ 7.644195] systemd-fstab-generator[116]: Mount point is not a valid path, ignoring.
[ 7.747303] systemd[110]: /lib/systemd/system-generators/systemd-fstab-generator terminated by signal ABRT.
[ 7.918808] scsi 2:0:0:0: Direct-Access Generic Ultra HS-COMBO 1.98 PQ: 0 ANSI: 0
[ 7.928760] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 7.937131] sd 2:0:0:0: [sdb] Attached SCSI removable disk
[ 8.703965] systemd[1]: Listening on udev Kernel Socket.
[ OK ] Listening on udev Kernel Socket.
[ 8.716950] systemd[1]: Listening on fsck to fsckd communication Socket.
[ OK ] Listening on fsck to fsckd communication Socket.
[ 8.731931] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[ OK ] Listening on /dev/initctl Compatibility Named Pipe.
[ 8.746753] systemd[1]: Reached target Remote File Systems (Pre).
[ OK ] Reached target Remote File Systems (Pre).
[ 8.761026] systemd[1]: Listening on Journal Socket.
[ OK ] Listening on Journal Socket.
[ 8.773692] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ OK ] Set up automount Arbitrary Executab...ats File System Automount Point.
[ 8.792987] systemd[1]: Listening on Journal Socket (/dev/log).
[ OK ] Listening on Journal Socket (/dev/log).
[ 8.805802] systemd[1]: Reached target Swap.
[ OK ] Reached target Swap.
[ 8.816042] systemd[1]: Created slice System Slice.
[ OK ] Created slice System Slice.
[ 8.829139] systemd[1]: Started Read required files in advance.
[ OK ] Started Read required files in advance.
[ 9.041561] systemd[1]: Starting Load Kernel Modules...
Starting Load Kernel Modules...
[ 9.056466] systemd[1]: Reached target Remote File Systems.
[ OK ] Reached target Remote File Systems.
[ 9.070204] systemd[1]: Created slice system-getty.slice.
[ OK ] Created slice system-getty.slice.
[ 9.083066] systemd[1]: Created slice User and Session Slice.
[ OK ] Created slice User and Session Slice.
[ 9.099834] systemd[1]: Starting Uncomplicated firewall...
Starting Uncomplicated firewall...
[ 9.113830] systemd[1]: Reached target Encrypted Volumes.
[ OK ] Reached target Encrypted Volumes.
[ 9.127319] systemd[1]: Created slice system-serial\x2dgetty.slice.
[ OK ] Created slice system-serial\x2dgetty.slice.
[ 9.145719] systemd[1]: Mounting Debug File System...
Mounting Debug File System...
[ 9.165781] systemd[1]: Mounting POSIX Message Queue File System...
Mounting POSIX Message Queue File System...
[ 9.191042] systemd[1]: Listening on udev Control Socket.
[ OK ] Listening on udev Control Socket.
[ 9.204064] systemd[1]: Listening on Syslog Socket.
[ OK ] Listening on Syslog Socket.
[ 9.241313] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ OK ] Started Forward Password Requests to Wall Directory Watch.
[ 9.259212] systemd[1]: Reached target User and Group Name Lookups.
[ OK ] Reached target User and Group Name Lookups.
[ 9.276965] systemd[1]: Reached target Slices.
[ OK ] Reached target Slices.
[ 9.291925] systemd[1]: Starting Journal Service...
Starting Journal Service...
[ 9.309897] systemd[1]: Starting Create list of required static device nodes for the current kernel...
Starting Create list of required st... nodes for the current kernel...
[ 9.339866] systemd[1]: Started Uncomplicated firewall.
[ OK ] Started Uncomplicated firewall.
[ 9.523413] systemd[1]: systemd-modules-load.service: Main process exited, code=exited, status=1/FAILURE
[ 9.540458] systemd[1]: Failed to start Load Kernel Modules.
[FAILED] Failed to start Load Kernel Modules.
See 'systemctl status systemd-modules-load.service' for details.
[ 9.561751] systemd[1]: systemd-modules-load.service: Unit entered failed state.
[ 9.569450] systemd[1]: systemd-modules-load.service: Failed with result 'exit-code'.
[ 9.592917] systemd[1]: Started Create list of required static device nodes for the current kernel.
[ OK ] Started Create list of required sta...ce nodes for the current kernel.
[ 9.624225] systemd[1]: Mounted Debug File System.
[ OK ] Mounted Debug File System.
[ 9.645485] systemd[1]: Mounted POSIX Message Queue File System.
[ OK ] Mounted POSIX Message Queue File System.
[ 9.681739] systemd[1]: ureadahead.service: Main process exited, code=exited, status=5/NOTINSTALLED
[ 9.693091] systemd[1]: ureadahead.service: Unit entered failed state.
[ 9.699745] systemd[1]: ureadahead.service: Failed with result 'exit-code'.
[ 9.753528] systemd[1]: Starting Create Static Device Nodes in /dev...
Starting Create Static Device Nodes in /dev...
[ 9.777165] systemd[1]: Mounting FUSE Control File System...
Mounting FUSE Control File System...
[ 9.797560] systemd[1]: Starting Apply Kernel Variables...
Starting Apply Kernel Variables...
[ 9.822354] systemd[1]: Mounting Configuration File System...
Mounting Configuration File System...
[ 9.850252] systemd[1]: Mounted FUSE Control File System.
[ OK ] Mounted FUSE Control File System.
[ 9.864937] systemd[1]: Mounted Configuration File System.
[ OK ] Mounted Configuration File System.
[ OK ] Started Apply Kernel Variables.
[ OK ] Started Journal Service.
[ OK ] Started Create Static Device Nodes in /dev.
Starting udev Kernel Device Manager...
[ OK ] Started udev Kernel Device Manager.
Starting File System Check on Root Device...
[ OK ] Started File System Check Daemon to report status.
[ OK ] Started File System Check on Root Device.
Starting Remount Root and Kernel File Systems...
[FAILED] Failed to start Remount Root and Kernel File Systems.
See 'systemctl status systemd-remount-fs.service' for details.
Starting Flush Journal to Persistent Storage...
Starting udev Coldplug all Devices...
[ OK ] Reached target Local File Systems (Pre).
Starting Load/Save Random Seed...
[ OK ] Started Load/Save Random Seed.
[ OK ] Started Flush Journal to Persistent Storage.
[ OK ] Started udev Coldplug all Devices.
[ OK ] Started Dispatch Password Requests to Console Directory Watch.
[ OK ] Found device /dev/ttyS0.
[ 13.798794] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: dma_dwc_xfer_setup returns NULL
[ 13.821775] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: dma_dwc_xfer_setup returns NULL
[ 13.852881] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: dma_dwc_xfer_setup returns NULL
[ OK ] Reached target Sound Card.
[ OK ] Created slice system-ifup.slice.
[ OK ] Found device /sys/subsystem/net/devices/eth0.
[ OK ] Found device WDC_WD5000AAKS-00V1A0 NTFS.
Mounting /media/NTFS...
[ OK ] Mounted /media/NTFS.
[ OK ] Reached target Local File Systems.
Starting LSB: AppArmor initialization...
Starting Create Volatile Files and Directories...
Starting Tell Plymouth To Write Out Runtime Data...
Starting Wait for all "auto" /etc/n... up for network-online.target...
Starting Clean up any mess left by 0dns-up...
[ OK ] Started Tell Plymouth To Write Out Runtime Data.
[ OK ] Started Create Volatile Files and Directories.
[ OK ] Reached target System Time Synchronized.
Starting Update UTMP about System Boot/Shutdown...
[ OK ] Started Update UTMP about System Boot/Shutdown.
[ OK ] Started Clean up any mess left by 0dns-up.
[ OK ] Started LSB: AppArmor initialization.
[ OK ] Started ifup for eth0.
Starting Nameserver information manager...
[ OK ] Started Nameserver information manager.
Starting LSB: Raise network interfaces....
Starting LSB: start Samba SMB/CIFS daemon (smbd)...
[ OK ] Started LSB: start Samba SMB/CIFS daemon (smbd).
[ OK ] Started Wait for all "auto" /etc/ne...be up for network-online.target.
[ 44.789143] ata3.00: failed command: READ FPDMA QUEUED
[ 44.794376] ata3.00: cmd 60/08:00:00:00:00/00:00:00:00:00/40 tag 0 ncq 4096 in
[ 44.794376] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 44.809351] ata3.00: status: { DRDY }
[ 45.137778] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: dma_dwc_xfer_setup returns NULL
[ 45.158850] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: dma_dwc_xfer_setup returns NULL
r LSB: Rai...ork interfaces. (44s / no limit)
[ 75.765297] ata3.00: failed command: READ FPDMA QUEUED
[ 75.770531] ata3.00: cmd 60/08:00:00:00:00/00:00:00:00:00/40 tag 0 ncq 4096 in
[ 75.770531] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 75.785501] ata3.00: status: { DRDY }
[ 76.098849] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: dma_dwc_xfer_setup returns NULL
*] A start job is running for LSB: Rai...interfa[ 76.115178] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: dma_dwc_xfer_setup returns NULL
ces. (1min 7s / no limit)[ 76.136847] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: dma_dwc_xfer_setup returns NULL
n 31s / no limit)
[ 106.742527] ata3.00: failed command: READ DMA
[ 106.746991] ata3.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 106.746991] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 106.762046] ata3.00: status: { DRDY }
[ 107.076848] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: dma_dwc_xfer_setup returns NULL
[ 107.091773] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: dma_dwc_xfer_setup returns NULL
nning for LSB: Rai...nterfaces. (1min 38s / no limit) ] A start job is running for LSB: Rai...nterfaces. (1min 53s / no limit)
[ 137.782048] ata3.00: failed command: READ DMA
[ 137.786491] ata3.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 137.786491] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 137.801484] ata3.00: status: { DRDY }
for LSB: Rai...interfaces. (2min 9s / no limit)[ 138.130785] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: dma_dwc_xfer_setup returns NULL
[ 138.151845] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: dma_dwc_xfer_setup returns NULL
[ OK ] Reached target System Initialization.
[ OK ] Started Trigger resolvconf update for networkd DNS.
[ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket.
[ OK ] Started Daily Cleanup of Temporary Directories.
[ OK ] Reached target Timers.
Starting Console System Startup Logging...
[ OK ] Listening on CUPS Scheduler.
Starting Restore Sound Card State...
[ OK ] Started CUPS Scheduler.
[ OK ] Reached target Paths.
[ OK ] Listening on D-Bus System Message Bus Socket.
[ OK ] Listening on UUID daemon activation socket.
[ OK ] Reached target Sockets.
[ OK ] Reached target Basic System.
Starting Modem Manager...
Starting Restore /etc/resolv.conf i...e the ppp link was shut down....
Starting LSB: start and stop timidity...
[ OK ] Started Regular background program processing daemon.
Starting Accounts Service...
Starting LSB: handle special hotkeys of Apple computers...
[ OK ] Started CUPS Scheduler.
Starting LSB: daemon to balance interrupts for SMP systems...
Starting Login Service...
[ OK ] Started crash report submission daemon.
Starting Network Manager...
Starting Initialize hardware monitoring sensors...
Starting System Logging Service...
Starting LSB: Set the CPU Frequency Scaling governor to "ondemand"...
Starting Avahi mDNS/DNS-SD Stack...
[ OK ] Started Cgroup management daemon.
Starting LSB: automatic crash report generation...
Starting Permit User Sessions...
[ OK ] Started Run anacron jobs.
[ OK ] Started D-Bus System Message Bus.
[ OK ] Started Avahi mDNS/DNS-SD Stack.
[ OK ] Started Network Manager.
[ OK ] Reached target Network.
[ OK ] Reached target Network is Online.
Starting LSB: start Samba daemons for the AD DC...
Starting LSB: disk temperature monitoring daemon...
Starting LSB: start Samba NetBIOS nameserver (nmbd)...
Starting LSB: Start NTP daemon...
Starting /etc/rc.local Compatibility...
[ OK ] Started Make remote CUPS printers available locally.
Starting LSB: Load kernel modules needed to enable cpufreq scaling...
Starting LSB: Start xrdp and sesman daemons...
Starting LSB: Tool to automatically...ubmit kernel crash signatures...
[ OK ] Started System Logging Service.
[ OK ] Started Console System Startup Logging.
[ OK ] Started Restore Sound Card State.
[ OK ] Started Restore /etc/resolv.conf if...ore the ppp link was shut down..
[ OK ] Started LSB: start and stop timidity.
[ OK ] Started LSB: handle special hotkeys of Apple computers.
[ OK ] Started LSB: daemon to balance interrupts for SMP systems.
[ OK ] Started LSB: Set the CPU Frequency Scaling governor to "ondemand".
[ OK ] Started LSB: automatic crash report generation.
[ OK ] Started Permit User Sessions.
[ OK ] Started LSB: disk temperature monitoring daemon.
[ OK ] Started /etc/rc.local Compatibility.
[ OK ] Started LSB: Load kernel modules needed to enable cpufreq scaling.
[ OK ] Started Initialize hardware monitoring sensors.
[ OK ] Started LSB: Tool to automatically ... submit kernel crash signatures.
[ OK ] Started LSB: Start NTP daemon.
[ OK ] Started LSB: Start xrdp and sesman daemons.
[ OK ] Started Login Service.
Starting Authenticate and Authorize Users to Run Privileged Tasks...
Starting Manage, Install and Generate Color Profiles...
Starting LSB: set CPUFreq kernel parameters...
Starting Light Display Manager...
Starting Hold until boot process finishes up...
[ OK ] Started Hold until boot process finishes up.
[ OK ] Started LSB: set CPUFreq kernel parameters.
[ OK ] Started Authenticate and Authorize Users to Run Privileged Tasks.
[ OK ] Started Accounts Service.
Starting WPA supplicant...
[ OK ] Started Serial Getty on ttyS0.
[ OK ] Started Getty on tty1.
[ OK ] Reached target Login Prompts.
[ OK ] Started Manage, Install and Generate Color Profiles.
[ OK ] Started Modem Manager.
[ OK ] Started Light Display Manager.
[ OK ] Started WPA supplicant.
Starting Network Manager Script Dispatcher Service...
[ OK ] Started Network Manager Script Dispatcher Service.
Ubuntu Xenial Xerus (development branch) Sam460ex ttyS0
Sam460ex login: [ 168.812924] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 168.830521] ata3.00: failed command: READ DMA
[ 168.841530] ata3.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 168.841530] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 168.870535] ata3.00: status: { DRDY }
[ 169.190057] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: dma_dwc_xfer_setup returns NULL
[ 169.215664] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: dma_dwc_xfer_setup returns NULL
[ 169.246746] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: dma_dwc_xfer_setup returns NULL
[ 199.788475] ata3.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 199.803744] ata3.00: failed command: READ DMA
[ 199.814375] ata3.00: cmd c8/00:08:00:00:00/00:00:00:00:00/e0 tag 0 dma 4096 in
[ 199.814375] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[ 199.845340] ata3.00: status: { DRDY }
[ 200.165795] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: dma_dwc_xfer_setup returns NULL
[ 200.194458] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: dma_dwc_xfer_setup returns NULL
[ 200.224548] sata-dwc 4bffd1000.sata: sata_dwc_qc_prep_by_tag: dma_dwc_xfer_setup returns NULL
[ 200.251506] blk_update_request: I/O error, dev sdc, sector 0
[ 200.272350] Buffer I/O error on dev sdc, logical block 0, async page read
next prev parent reply other threads:[~2015-12-19 20:17 UTC|newest]
Thread overview: 154+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-12-15 23:25 [PATCH 1/3] ata: sata_dwc_460ex: use "dmas" DT property to find dma channel Mans Rullgard
2015-12-15 23:25 ` [PATCH 2/3] ata: sata_dwc_460ex: add phy support Mans Rullgard
2015-12-16 11:14 ` Sergei Shtylyov
2015-12-16 11:24 ` Måns Rullgård
2015-12-15 23:25 ` [PATCH 3/3] ata: sata_dwc_460ex: get rid of global data Mans Rullgard
2015-12-17 15:06 ` Andy Shevchenko
2015-12-17 15:19 ` Måns Rullgård
2015-12-17 15:37 ` Andy Shevchenko
2015-12-17 15:57 ` Måns Rullgård
2015-12-15 23:34 ` [PATCH 1/3] ata: sata_dwc_460ex: use "dmas" DT property to find dma channel Måns Rullgård
2015-12-17 14:59 ` Andy Shevchenko
2015-12-17 15:13 ` Måns Rullgård
2015-12-17 15:55 ` Andy Shevchenko
2015-12-17 16:04 ` Måns Rullgård
2015-12-17 16:53 ` Andy Shevchenko
2015-12-17 17:57 ` Julian Margetson
2015-12-17 17:59 ` Måns Rullgård
[not found] ` <567302E8.5050303@candw.ms>
2015-12-17 18:51 ` Måns Rullgård
[not found] ` <5673061A.4070700@candw.ms>
2015-12-17 19:53 ` Måns Rullgård
[not found] ` <56732C04.9040100@candw.ms>
2015-12-18 0:06 ` Måns Rullgård
2015-12-18 0:59 ` Julian Margetson
2015-12-18 1:38 ` Måns Rullgård
2015-12-18 11:48 ` Julian Margetson
2015-12-18 12:04 ` Måns Rullgård
2015-12-18 12:23 ` Andy Shevchenko
2015-12-18 12:49 ` Måns Rullgård
[not found] ` <5674271B.9090308@candw.ms>
2015-12-18 17:18 ` Måns Rullgård
2015-12-18 18:48 ` Andy Shevchenko
[not found] ` <56745BA4.1090607@candw.ms>
2015-12-18 22:33 ` Måns Rullgård
2015-12-18 22:49 ` Julian Margetson
2015-12-18 23:16 ` Måns Rullgård
2015-12-19 2:34 ` Andy Shevchenko
2015-12-19 11:39 ` Julian Margetson
2015-12-19 15:40 ` Måns Rullgård
2015-12-19 15:40 ` Måns Rullgård
[not found] ` <567585CD.9080105@candw.ms>
2015-12-19 16:39 ` Måns Rullgård
2015-12-19 16:39 ` Måns Rullgård
2015-12-19 16:56 ` Andy Shevchenko
2015-12-19 17:05 ` Måns Rullgård
2015-12-19 17:05 ` Måns Rullgård
2015-12-19 17:09 ` Julian Margetson
2015-12-19 17:11 ` Andy Shevchenko
2015-12-19 17:19 ` Måns Rullgård
2015-12-19 17:19 ` Måns Rullgård
2015-12-19 18:56 ` Julian Margetson
2015-12-19 19:07 ` Måns Rullgård
2015-12-19 19:07 ` Måns Rullgård
2015-12-19 20:16 ` Julian Margetson [this message]
2015-12-19 20:39 ` Andy Shevchenko
2015-12-19 20:41 ` Måns Rullgård
2015-12-19 20:41 ` Måns Rullgård
2015-12-19 20:48 ` Julian Margetson
2015-12-19 20:55 ` Julian Margetson
2015-12-20 17:11 ` Måns Rullgård
2015-12-20 17:11 ` Måns Rullgård
2015-12-20 17:41 ` Andy Shevchenko
2015-12-20 17:54 ` Måns Rullgård
2015-12-20 17:54 ` Måns Rullgård
2015-12-20 17:44 ` Julian Margetson
2015-12-20 18:49 ` Måns Rullgård
2015-12-20 18:49 ` Måns Rullgård
2015-12-20 20:17 ` Andy Shevchenko
2015-12-20 20:55 ` Andy Shevchenko
2015-12-21 1:19 ` Måns Rullgård
2015-12-21 1:19 ` Måns Rullgård
2015-12-21 19:08 ` Andy Shevchenko
2015-12-21 19:27 ` Måns Rullgård
2015-12-21 19:27 ` Måns Rullgård
2015-12-21 20:54 ` Andy Shevchenko
2015-12-21 21:06 ` Måns Rullgård
2015-12-21 21:06 ` Måns Rullgård
2015-12-22 0:08 ` Måns Rullgård
2015-12-22 0:08 ` Måns Rullgård
2015-12-22 10:58 ` Andy Shevchenko
2016-01-06 16:26 ` Måns Rullgård
2016-01-06 16:26 ` Måns Rullgård
2016-01-06 17:36 ` Andy Shevchenko
2016-01-07 9:34 ` Andy Shevchenko
2016-01-07 18:32 ` Måns Rullgård
2016-01-07 18:32 ` Måns Rullgård
2016-01-08 8:57 ` Andy Shevchenko
2016-01-08 10:57 ` Måns Rullgård
2016-01-08 10:57 ` Måns Rullgård
2016-01-20 18:50 ` Måns Rullgård
2016-01-20 18:50 ` Måns Rullgård
2016-01-20 19:23 ` Andy Shevchenko
2016-01-20 19:24 ` Måns Rullgård
2016-01-20 19:24 ` Måns Rullgård
2016-01-20 19:38 ` Andy Shevchenko
2016-01-20 19:46 ` Måns Rullgård
2016-01-20 19:46 ` Måns Rullgård
2016-01-20 19:51 ` Andy Shevchenko
2016-01-20 20:07 ` Måns Rullgård
2016-01-20 20:07 ` Måns Rullgård
2016-01-22 10:04 ` Andy Shevchenko
2016-01-22 11:13 ` Måns Rullgård
2016-01-22 11:13 ` Måns Rullgård
2016-01-22 11:56 ` Andy Shevchenko
2016-01-22 12:05 ` Måns Rullgård
2016-01-22 12:05 ` Måns Rullgård
2016-01-22 12:15 ` Andy Shevchenko
2015-12-21 16:48 ` Andy Shevchenko
2015-12-21 17:20 ` Julian Margetson
2015-12-21 17:26 ` Julian Margetson
2015-12-21 17:55 ` Andy Shevchenko
2015-12-21 18:23 ` Julian Margetson
2015-12-21 18:27 ` Måns Rullgård
2015-12-21 18:27 ` Måns Rullgård
2015-12-21 19:08 ` Julian Margetson
2015-12-21 19:19 ` Julian Margetson
2015-12-21 19:27 ` Måns Rullgård
2015-12-21 19:27 ` Måns Rullgård
2015-12-21 19:47 ` Julian Margetson
2015-12-21 20:25 ` Andy Shevchenko
2015-12-21 20:29 ` Julian Margetson
2016-01-22 10:07 ` Andy Shevchenko
2015-12-21 20:33 ` Måns Rullgård
2015-12-21 20:33 ` Måns Rullgård
2015-12-21 18:25 ` Måns Rullgård
2015-12-21 18:25 ` Måns Rullgård
2015-12-21 0:47 ` Måns Rullgård
2015-12-21 0:47 ` Måns Rullgård
2015-12-21 0:53 ` Måns Rullgård
2015-12-21 0:53 ` Måns Rullgård
2015-12-21 0:58 ` Måns Rullgård
2015-12-21 0:58 ` Måns Rullgård
2015-12-21 8:40 ` Andy Shevchenko
2015-12-21 12:15 ` Måns Rullgård
2015-12-21 12:15 ` Måns Rullgård
2015-12-21 17:24 ` Andy Shevchenko
2015-12-21 18:16 ` Måns Rullgård
2015-12-21 18:16 ` Måns Rullgård
2015-12-21 19:23 ` Andy Shevchenko
2015-12-21 19:50 ` Måns Rullgård
2015-12-21 19:50 ` Måns Rullgård
[not found] ` <5677D447.40906@candw.ms>
2015-12-21 12:16 ` Måns Rullgård
2015-12-21 12:16 ` Måns Rullgård
2015-12-21 13:18 ` Julian Margetson
2015-12-21 13:24 ` Måns Rullgård
2015-12-21 13:24 ` Måns Rullgård
2015-12-21 14:40 ` Julian Margetson
2015-12-21 15:24 ` Måns Rullgård
2015-12-21 15:24 ` Måns Rullgård
2015-12-21 16:44 ` Andy Shevchenko
2015-12-21 18:19 ` Måns Rullgård
2015-12-21 18:19 ` Måns Rullgård
2015-12-18 12:33 ` Julian Margetson
2015-12-18 12:38 ` Andy Shevchenko
2015-12-18 12:45 ` Måns Rullgård
[not found] ` <56740F9F.5020500@candw.ms>
2015-12-18 14:24 ` Andy Shevchenko
2015-12-18 14:27 ` Måns Rullgård
2015-12-18 10:08 ` Andy Shevchenko
2015-12-18 11:24 ` Måns Rullgård
2015-12-17 14:58 ` Andy Shevchenko
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=5675BB2F.6060107@candw.ms \
--to=runaway@candw.ms \
--cc=andriy.shevchenko@linux.intel.com \
--cc=andy.shevchenko@gmail.com \
--cc=linux-ide@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=mans@mansr.com \
--cc=tj@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.