* Queries about ath10k driver and QCA988x based radio from sparklan
@ 2015-12-25 11:14 Ankur Saxena
2015-12-25 12:10 ` Sunder Kumaresan
0 siblings, 1 reply; 6+ messages in thread
From: Ankur Saxena @ 2015-12-25 11:14 UTC (permalink / raw)
To: ath10k
[-- Attachment #1: Type: text/plain, Size: 1918 bytes --]
Hi All,
We have purchased radio module "WPEA-352ACN" from SparkLan. We are using
this radio module with ViaTech board for 802.11 AC functionality. We are
running linux kernel 3.19.1 with atheros driver ath10k up with all the
configuration elements.
We are facing some issues in getting up 802.11 AC functionality for the
radio. Please find below the queries:
1) We are using latest ath10k driver with 802.11AC configuration
enabled. On loading the driver for ath10k, we are not seeing "802.11AC"
in iwconfig utility for wlan interface. It is showing only 802.11 abgn
for the interface.
2) Tried to make AP using the interface by taking help of hostapd
utility. Searched on internet for configuration related to making 802.11
AC AP and used them all. In this case, Mode parameter in iwconfig is
changed to Master which shows AP functionality, but the interface is
still showing 802.11 abgn supported only.
3) We are using plain text version of regulatory database file (DB.txt)
which is maintained for use of CRDA. We are making sure that DB.txt file
is parsed properly and the database is added into MAC driver by parsing
the database file.
4) While running hostapd with full configuration for 802.11AC AP
settings, no error is seen for setting up the interface. Channel setting
is done for Auto-configuration and VHT settings are also applied in the
configuration file. The interface is not able to get up in 802.11 AC
mode, instead it is coming up only in 802.11 abgn only.
5) There is one error seen after firmware gets downloaded and starts
running. The error is as below:
ath10k_pci 0000:02:00.0: Direct firmware load for
ath10k/cal-pci-0000:02:00.0.bin failed with error -2
Can this may create this issue to happen also?
Please find attached the DB.txt and hostapd configuration file for
reference.
Can anyone please help us in getting 802.11 AC mode up and running in
the radio.
[-- Attachment #2: db.txt --]
[-- Type: text/plain, Size: 33656 bytes --]
# This is the world regulatory domain
country 00:
(2402 - 2472 @ 40), (20)
# Channel 12 - 13.
(2457 - 2482 @ 40), (20), NO-IR
# Channel 14. Only JP enables this and for 802.11b only
(2474 - 2494 @ 20), (20), NO-IR, NO-OFDM
# Channel 36 - 48
(5170 - 5250 @ 80), (20), NO-IR, AUTO-BW
# Channel 52 - 64
(5250 - 5330 @ 80), (20), NO-IR, DFS, AUTO-BW
# Channel 100 - 144
(5490 - 5730 @ 160), (20), NO-IR, DFS
# Channel 149 - 165
(5735 - 5835 @ 80), (20), NO-IR
# IEEE 802.11ad (60GHz), channels 1..3
(57240 - 63720 @ 2160), (0)
country AD:
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20)
(5250 - 5330 @ 80), (20), DFS
(5490 - 5710 @ 80), (27), DFS
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
country AE: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (17), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country AF: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# Source:
# http://pucanguilla.org/Downloads/January2005-Anguilla%20Table%20of%20Allocations.pdf
country AI: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
country AL: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20.00), AUTO-BW
(5250 - 5330 @ 80), (20.00), DFS, AUTO-BW
(5490 - 5710 @ 160), (27.00), DFS
country AM: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (18)
(5250 - 5330 @ 80), (18), DFS
country AN: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
country AR: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (17), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country AS: DFS-FCC
(2402 - 2472 @ 40), (30)
(5170 - 5250 @ 80), (24), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country AT: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
country AU:
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (17), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5710 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country AW: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
country AZ: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (18), AUTO-BW
(5250 - 5330 @ 80), (18), DFS, AUTO-BW
country BA: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
country BB: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (23), AUTO-BW
(5250 - 5330 @ 80), (23), DFS, AUTO-BW
(5735 - 5835 @ 80), (30)
country BD: DFS-JP
(2402 - 2482 @ 40), (20)
(5735 - 5835 @ 80), (30)
country BE: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
country BF: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (17), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country BG: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
country BH: DFS-JP
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20)
(5250 - 5330 @ 80), (20), DFS
(5735 - 5835 @ 80), (20)
country BL: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
country BM: DFS-FCC
(2402 - 2472 @ 40), (30)
(5170 - 5250 @ 80), (24), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country BN: DFS-JP
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5735 - 5835 @ 80), (20)
country BO: DFS-JP
(2402 - 2482 @ 40), (20)
(5250 - 5330 @ 80), (30), DFS
(5735 - 5835 @ 80), (30)
country BR: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (17), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country BS: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (24), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
# Source:
# http://www.bicma.gov.bt/paper/publication/nrrpart4.pdf
country BT: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
country BY: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
country BZ: DFS-JP
(2402 - 2482 @ 40), (30)
(5735 - 5835 @ 80), (30)
country CA: DFS-FCC
(2402 - 2472 @ 40), (30)
(5170 - 5250 @ 80), (17), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
# Source:
# http://www.art-rca.org
country CF: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 40), (17)
(5250 - 5330 @ 40), (24), DFS
(5490 - 5730 @ 40), (24), DFS
(5735 - 5835 @ 40), (30)
country CH: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
country CI: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (17), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country CL: DFS-JP
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5735 - 5835 @ 80), (20)
country CN: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (23), AUTO-BW
(5250 - 5330 @ 80), (23), DFS, AUTO-BW
(5735 - 5835 @ 80), (30)
# 60 gHz band channels 1,4: 28dBm, channels 2,3: 44dBm
# ref: http://www.miit.gov.cn/n11293472/n11505629/n11506593/n11960250/n11960606/n11960700/n12330791.files/n12330790.pdf
(57240 - 59400 @ 2160), (28)
(59400 - 63720 @ 2160), (44)
(63720 - 65880 @ 2160), (28)
country CO: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (17), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country CR: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (17)
(5250 - 5330 @ 80), (24), DFS
(5490 - 5730 @ 80), (24), DFS
(5735 - 5835 @ 80), (30)
country CX: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (24), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country CY: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
# Data from http://www.ctu.eu/164/download/VOR/VOR-12-08-2005-34.pdf
# and http://www.ctu.eu/164/download/VOR/VOR-12-05-2007-6-AN.pdf
# Power at 5250 - 5350 MHz and 5470 - 5725 MHz can be doubled if TPC is
# implemented.
country CZ: DFS-ETSI
(2400 - 2483.5 @ 40), (100 mW)
(5150 - 5250 @ 80), (200 mW), NO-OUTDOOR, AUTO-BW
(5250 - 5350 @ 80), (100 mW), NO-OUTDOOR, DFS, AUTO-BW
(5470 - 5725 @ 160), (500 mW), DFS
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
# Data from "Frequenznutzungsplan" (as published in April 2008), downloaded from
# http://www.bundesnetzagentur.de/cae/servlet/contentblob/38448/publicationFile/2659/Frequenznutzungsplan2008_Id17448pdf.pdf
# For the 5GHz range also see
# http://www.bundesnetzagentur.de/cae/servlet/contentblob/38216/publicationFile/6579/WLAN5GHzVfg7_2010_28042010pdf.pdf
# The values have been reduced by a factor of 2 (3db) for non TPC devices
# (in other words: devices with TPC can use twice the tx power of this table).
# Note that the docs do not require TPC for 5150--5250; the reduction to
# 100mW thus is not strictly required -- however the conservative 100mW
# limit is used here as the non-interference with radar and satellite
# apps relies on the attenuation by the building walls only in the
# absence of DFS; the neighbour countries have 100mW limit here as well.
country DE: DFS-ETSI
# entries 279004 and 280006
(2400 - 2483.5 @ 40), (100 mW)
# entry 303005
(5150 - 5250 @ 80), (100 mW), NO-OUTDOOR, AUTO-BW
# entries 304002 and 305002
(5250 - 5350 @ 80), (100 mW), NO-OUTDOOR, DFS, AUTO-BW
# entries 308002, 309001 and 310003
(5470 - 5725 @ 160), (500 mW), DFS
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
country DK: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
# Source:
# http://www.ntrcdom.org/index.php?option=com_content&view=category&layout=blog&id=10&Itemid=55
country DM: DFS-FCC
(2402 - 2472 @ 40), (30)
(5170 - 5250 @ 80), (17), AUTO-BW
(5250 - 5330 @ 80), (23), DFS, AUTO-BW
(5735 - 5835 @ 80), (30)
country DO: DFS-FCC
(2402 - 2472 @ 40), (30)
(5170 - 5250 @ 80), (17), AUTO-BW
(5250 - 5330 @ 80), (23), DFS, AUTO-BW
(5735 - 5835 @ 80), (30)
country DZ: DFS-JP
(2402 - 2482 @ 40), (20)
(5170.000 - 5250.000 @ 80.000), (23.00), AUTO-BW
(5250.000 - 5330.000 @ 80.000), (23.00), DFS, AUTO-BW
(5490.000 - 5670.000 @ 160.000), (23.00), DFS
country EC: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (17)
(5250 - 5330 @ 80), (24), DFS
(5490 - 5730 @ 80), (24), DFS
(5735 - 5835 @ 80), (30)
country EE: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
country EG: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20)
(5250 - 5330 @ 80), (20), DFS
# Orden IET/787/2013, de 25 de abril, por la que se aprueba
# el cuadro nacional de atribución de frecuencias.
# http://www.boe.es/diario_boe/txt.php?id=BOE-A-2013-4845
#
# more info at "Cuadro nacional de atribución de frecuencias (CNAF)":
# http://www.minetur.gob.es/telecomunicaciones/espectro/paginas/cnaf.aspx
country ES: DFS-ETSI
(2400 - 2483.5 @ 40), (100 mW)
(5150 - 5250 @ 80), (200 mW), NO-OUTDOOR, AUTO-BW
(5250 - 5350 @ 80), (100 mW), NO-OUTDOOR, DFS, AUTO-BW
(5470 - 5725 @ 160), (500 mW), DFS
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
country ET: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
country FI: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
country FM: DFS-FCC
(2402 - 2472 @ 40), (30)
(5170 - 5250 @ 80), (24), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country FR: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
country GB: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
country GD: DFS-FCC
(2402 - 2472 @ 40), (30)
(5170 - 5250 @ 80), (17), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country GE: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (18), AUTO-BW
(5250 - 5330 @ 80), (18), DFS, AUTO-BW
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
country GF: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
country GH: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (17), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country GL: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20)
(5250 - 5330 @ 80), (20), DFS
(5490 - 5710 @ 80), (27), DFS
country GP: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
country GR: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
country GT: DFS-FCC
(2402 - 2472 @ 40), (30)
(5170 - 5250 @ 80), (17), AUTO-BW
(5250 - 5330 @ 80), (23), DFS, AUTO-BW
(5735 - 5835 @ 80), (30)
country GU: DFS-FCC
(2402 - 2472 @ 40), (30)
(5170 - 5250 @ 80), (17)
(5250 - 5330 @ 80), (24), DFS
(5490 - 5730 @ 80), (24), DFS
(5735 - 5835 @ 80), (30)
country GY:
(2402 - 2482 @ 40), (30)
(5735 - 5835 @ 80), (30)
country HK:
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (17), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5710 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country HN: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (17), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country HR: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
country HT: DFS-FCC
(2402 - 2472 @ 40), (30)
(5170 - 5250 @ 80), (24), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country HU: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
country ID: DFS-JP
# ref: http://www.postel.go.id/content/ID/regulasi/standardisasi/kepdir/bwa%205,8%20ghz.pdf
(2402 - 2482 @ 40), (20)
(5735 - 5815 @ 80), (23)
country IE: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
country IL: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5150 - 5250 @ 80), (200 mW), NO-OUTDOOR, AUTO-BW
(5250 - 5350 @ 80), (200 mW), NO-OUTDOOR, DFS, AUTO-BW
country IN: DFS-JP
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5735 - 5835 @ 80), (20)
country IR: DFS-JP
(2402 - 2482 @ 40), (20)
(5735 - 5835 @ 80), (30)
country IS: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
country IT: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
country JM: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (17), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country JO: DFS-JP
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (23)
(5735 - 5835 @ 80), (23)
country JP: DFS-JP
(2402 - 2482 @ 40), (20)
(2474 - 2494 @ 20), (20), NO-OFDM
(4910 - 4990 @ 40), (23)
(5030 - 5090 @ 40), (23)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (23), DFS
country KE: DFS-JP
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (23)
(5490 - 5570 @ 80), (30), DFS
(5735 - 5775 @ 40), (23)
country KH: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# Source
# http://ntrc.kn/?page_id=7
country KN: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (30), DFS
(5735 - 5815 @ 80), (30)
country KP: DFS-JP
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5630 @ 80), (30), DFS
(5735 - 5815 @ 80), (30)
country KR: DFS-JP
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (30), DFS
(5735 - 5835 @ 80), (30)
country KW: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
country KY: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (24), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country KZ:
(2402 - 2482 @ 40), (20)
country LB: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (17), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
# Source:
# http://www.ntrc.org.lc/operational_structures.htm
country LC: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (30), DFS
(5735 - 5815 @ 80), (30)
country LI: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
country LK: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (17)
(5250 - 5330 @ 80), (24), DFS
(5490 - 5730 @ 80), (24), DFS
(5735 - 5835 @ 80), (30)
# Source:
# http://lca.org.ls/images/documents/lesotho_national_frequency_allocation_plan.pdf
country LS: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
country LT: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
country LU: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
country LV: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
country MA: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
country MC: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# Source:
# http://www.cnfr.md/index.php?pag=sec&id=117&l=en
country MD: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# Source:
# http://www.cept.org/files/1050/Tools%20and%20Services/EFIS%20-%20ECO%20Frequency%20Information%20System/National%20frequency%20tables/Montenegro%20NAFT%20-%202010.pdf
country ME: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
country MF: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
country MH: DFS-FCC
(2402 - 2472 @ 40), (30)
(5170 - 5250 @ 80), (24), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country MK: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
country MN: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (24), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country MO:
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 40), (23)
(5250 - 5330 @ 40), (23), DFS
(5735 - 5835 @ 40), (30)
country MP: DFS-FCC
(2402 - 2472 @ 40), (30)
(5170 - 5250 @ 80), (24), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country MQ: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# Source:
# http://www.are.mr/pdfs/telec_freq_TNAbf_2010.pdf
country MR: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
country MT: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
country MU: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (24), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country MW: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
country MX: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (17), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country MY: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (17), AUTO-BW
(5250 - 5330 @ 80), (23), DFS, AUTO-BW
(5735 - 5835 @ 80), (30)
country NI: DFS-FCC
(2402 - 2472 @ 40), (30)
(5170 - 5250 @ 80), (24), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country NL: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), NO-OUTDOOR, AUTO-BW
(5250 - 5330 @ 80), (20), NO-OUTDOOR, DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
# Data from http://www.lovdata.no/dokument/SF/forskrift/2012-01-19-77
# Power at 5250 - 5350 MHz, 5470 - 5725 MHz and 5815 – 5850 MHz can
# be doubled if TPC is implemented.
# Up to 2W (or 4W with TPC) is allowed in the 5725 – 5795 MHz band
# which has been merged with 5470 - 5725 MHz to allow wide channels
country NO: DFS-ETSI
(2400 - 2483.5 @ 40), (100 mW)
(5150 - 5250 @ 80), (200 mW), AUTO-BW
(5250 - 5350 @ 80), (100 mW), DFS, AUTO-BW
(5470 - 5795 @ 160), (500 mW), DFS
(5815 - 5850 @ 35), (2000 mW), DFS
(17100 - 17300 @ 200), (100 mW)
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
country NP: DFS-JP
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5735 - 5835 @ 80), (20)
country NZ: DFS-FCC
(2402 - 2482 @ 40), (30)
(5170 - 5250 @ 80), (17), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country OM: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
country PA: DFS-FCC
(2402 - 2472 @ 40), (30)
(5170 - 5250 @ 80), (17), AUTO-BW
(5250 - 5330 @ 80), (23), DFS, AUTO-BW
(5735 - 5835 @ 80), (30)
country PE: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (17), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country PF: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
country PG: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (17), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country PH: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (17), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country PK: DFS-JP
(2402 - 2482 @ 40), (20)
(5735 - 5835 @ 80), (30)
country PL: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
country PM: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
country PR: DFS-FCC
(2402 - 2472 @ 40), (30)
(5170 - 5250 @ 80), (17), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country PT: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
country PW: DFS-FCC
(2402 - 2472 @ 40), (30)
(5170 - 5250 @ 80), (24), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country PY: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (24), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country QA: DFS-JP
(2402 - 2482 @ 40), (20)
(5735 - 5835 @ 80), (30)
country RE: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
country RO: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
# Source:
# http://www.ratel.rs/upload/documents/Plan_namene/Plan_namene-sl_glasnik.pdf
country RS: DFS-ETSI
(2400 - 2483.5 @ 40), (100 mW)
(5150 - 5350 @ 40), (200 mW), NO-OUTDOOR
(5470 - 5725 @ 20), (1000 mW), DFS
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
country RU: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20)
(5250 - 5330 @ 80), (20), DFS
(5650 - 5730 @ 80), (30), DFS
(5735 - 5835 @ 80), (30)
country RW: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (17), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country SA: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
country SE: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
country SG: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (17), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country SI: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
country SK: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
# Source:
# Regulation N° 2004-005 ART/DG/DRC/D.Rég
country SN: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (17), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country SR: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
country SV: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (17)
(5250 - 5330 @ 80), (23), DFS
(5735 - 5835 @ 80), (30)
country SY:
(2402 - 2482 @ 40), (20)
# Source:
# http://www.telecommission.tc/Spectrum-plan20110324-101210.html
country TC: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (24), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country TD: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
country TG: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 40), (20)
(5250 - 5330 @ 40), (20), DFS
(5490 - 5710 @ 40), (27), DFS
country TH: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (17), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country TN: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
country TR: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
country TT: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (17), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country TW: DFS-JP
(2402 - 2472 @ 40), (30)
(5270 - 5330 @ 40), (17), DFS
(5490 - 5590 @ 80), (30), DFS
(5650 - 5710 @ 40), (30), DFS
(5735 - 5835 @ 80), (30)
# Source:
# #914 / 06 Sep 2007: http://www.ucrf.gov.ua/uk/doc/nkrz/1196068874
# #1174 / 23 Oct 2008: http://www.nkrz.gov.ua/uk/activities/ruling/1225269361
# (appendix 8)
# Listed 5GHz range is a lowest common denominator for all related
# rules in the referenced laws. Such a range is used because of
# disputable definitions there.
country UA: DFS-ETSI
(2400 - 2483.5 @ 40), (20), NO-OUTDOOR
(5150 - 5350 @ 40), (20), NO-OUTDOOR
(5490 - 5670 @ 80), (20), DFS
(5735 - 5835 @ 80), (20)
# 60 gHz band channels 1-4, ref: Etsi En 302 567
(57000 - 66000 @ 2160), (40)
country UG: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (24), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country US: DFS-FCC
(2402 - 2472 @ 40), (30)
(5170 - 5250 @ 80), (17), AUTO-BW
(5250 - 5330 @ 80), (23), DFS, AUTO-BW
(5735 - 5835 @ 80), (30)
# 60g band
# reference: http://cfr.regstoday.com/47cfr15.aspx#47_CFR_15p255
# channels 1,2,3, EIRP=40dBm(43dBm peak)
(57240 - 63720 @ 2160), (40)
country UY: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (17), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
# Source:
# http://cemc.uz/article/1976/
country UZ: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
# Source:
# http://www.ntrc.vc/regulations/Jun_2006_Spectrum_Managment_Regulations.pdf
country VC: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
# Source:
# Official Gazette (Gaceta Oficial) concerning Unlicensed transmitter use
# (10 June 2013)
# http://www.conatel.gob.ve/
country VE: DFS-FCC
(2402 - 2482 @ 40), (30)
(5170 - 5250 @ 80), (23), AUTO-BW
(5250 - 5330 @ 80), (23), DFS, AUTO-BW
(5735 - 5835 @ 80), (30)
country VI: DFS-FCC
(2402 - 2472 @ 40), (30)
(5170 - 5250 @ 80), (24), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country VN: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (17)
(5250 - 5330 @ 80), (24), DFS
(5490 - 5730 @ 80), (24), DFS
(5735 - 5835 @ 80), (30)
# Source:
# http://www.trr.vu/attachments/category/130/GURL_for_Short-range_Radiocommunication_Devices2.pdf
country VU: DFS-FCC
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (17), AUTO-BW
(5250 - 5330 @ 80), (24), DFS, AUTO-BW
(5490 - 5730 @ 160), (24), DFS
(5735 - 5835 @ 80), (30)
country WF: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
country YE:
(2402 - 2482 @ 40), (20)
country YT: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
country ZA: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
country ZW: DFS-ETSI
(2402 - 2482 @ 40), (20)
(5170 - 5250 @ 80), (20), AUTO-BW
(5250 - 5330 @ 80), (20), DFS, AUTO-BW
(5490 - 5710 @ 160), (27), DFS
[-- Attachment #3: hostapd_full.conf --]
[-- Type: text/plain, Size: 1429 bytes --]
### hostapd configuration file
interface=wlan0
driver=nl80211
### IEEE 802.11
ssid=ath10k
hw_mode=a
channel=0
max_num_sta=128
auth_algs=1
disassoc_low_ack=1
### DFS
ieee80211h=1
ieee80211d=1
country_code=CA
### IEEE 802.11n
ieee80211n=1
ht_capab=[HT40+][LDPC][SHORT-GI-20][SHORT-GI-40][TX-STBC][RX-STBC1][DSSS_CCK-40]
### IEEE 802.11ac
ieee80211ac=1
vht_oper_chwidth=1
vht_capab=[VHT80+][MAX-MPDU-11454][RXLDPC][SHORT-GI-80][TX-STBC-2BY1][RX-STBC-1]
vht_oper_centr_freq_seg0_idx=42
### hostapd event logger configuration
logger_syslog=-1
logger_syslog_level=1
logger_stdout=-1
logger_stdout_level=1
### WMM
wmm_enabled=1
uapsd_advertisement_enabled=1
wmm_ac_bk_cwmin=4
wmm_ac_bk_cwmax=10
wmm_ac_bk_aifs=7
wmm_ac_bk_txop_limit=0
wmm_ac_bk_acm=0
wmm_ac_be_aifs=3
wmm_ac_be_cwmin=4
wmm_ac_be_cwmax=10
wmm_ac_be_txop_limit=0
wmm_ac_be_acm=0
wmm_ac_vi_aifs=2
wmm_ac_vi_cwmin=3
wmm_ac_vi_cwmax=4
wmm_ac_vi_txop_limit=94
wmm_ac_vi_acm=0
wmm_ac_vo_aifs=2
wmm_ac_vo_cwmin=2
wmm_ac_vo_cwmax=3
wmm_ac_vo_txop_limit=47
wmm_ac_vo_acm=0
### TX queue parameters
tx_queue_data3_aifs=7
tx_queue_data3_cwmin=15
tx_queue_data3_cwmax=1023
tx_queue_data3_burst=0
tx_queue_data2_aifs=3
tx_queue_data2_cwmin=15
tx_queue_data2_cwmax=63
tx_queue_data2_burst=0
tx_queue_data1_aifs=1
tx_queue_data1_cwmin=7
tx_queue_data1_cwmax=15
tx_queue_data1_burst=3.0
tx_queue_data0_aifs=1
tx_queue_data0_cwmin=3
tx_queue_data0_cwmax=7
tx_queue_data0_burst=1.5
[-- Attachment #4: Type: text/plain, Size: 146 bytes --]
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Queries about ath10k driver and QCA988x based radio from sparklan
2015-12-25 11:14 Queries about ath10k driver and QCA988x based radio from sparklan Ankur Saxena
@ 2015-12-25 12:10 ` Sunder Kumaresan
0 siblings, 0 replies; 6+ messages in thread
From: Sunder Kumaresan @ 2015-12-25 12:10 UTC (permalink / raw)
To: Ankur Saxena, ath10k@lists.infradead.org
Did you update your firmware ?
https://wireless.wiki.kernel.org/en/users/drivers/ath10k/firmware
It worked for us in 3.18 Kernel
Use the above link.
Best Regards,
Sunder
________________________________________
From: ath10k <ath10k-bounces@lists.infradead.org> on behalf of Ankur Saxena <ankur.saxena@sibridgetech.com>
Sent: Friday, December 25, 2015 4:44 PM
To: ath10k@lists.infradead.org
Subject: Queries about ath10k driver and QCA988x based radio from sparklan
Hi All,
We have purchased radio module "WPEA-352ACN" from SparkLan. We are using
this radio module with ViaTech board for 802.11 AC functionality. We are
running linux kernel 3.19.1 with atheros driver ath10k up with all the
configuration elements.
We are facing some issues in getting up 802.11 AC functionality for the
radio. Please find below the queries:
1) We are using latest ath10k driver with 802.11AC configuration
enabled. On loading the driver for ath10k, we are not seeing "802.11AC"
in iwconfig utility for wlan interface. It is showing only 802.11 abgn
for the interface.
2) Tried to make AP using the interface by taking help of hostapd
utility. Searched on internet for configuration related to making 802.11
AC AP and used them all. In this case, Mode parameter in iwconfig is
changed to Master which shows AP functionality, but the interface is
still showing 802.11 abgn supported only.
3) We are using plain text version of regulatory database file (DB.txt)
which is maintained for use of CRDA. We are making sure that DB.txt file
is parsed properly and the database is added into MAC driver by parsing
the database file.
4) While running hostapd with full configuration for 802.11AC AP
settings, no error is seen for setting up the interface. Channel setting
is done for Auto-configuration and VHT settings are also applied in the
configuration file. The interface is not able to get up in 802.11 AC
mode, instead it is coming up only in 802.11 abgn only.
5) There is one error seen after firmware gets downloaded and starts
running. The error is as below:
ath10k_pci 0000:02:00.0: Direct firmware load for
ath10k/cal-pci-0000:02:00.0.bin failed with error -2
Can this may create this issue to happen also?
Please find attached the DB.txt and hostapd configuration file for
reference.
Can anyone please help us in getting 802.11 AC mode up and running in
the radio.
"DISCLAIMER: This message is proprietary to Aricent and is intended solely for the use of the individual to whom it is addressed. It may contain privileged or confidential information and should not be circulated or used for any purpose other than for what it is intended. If you have received this message in error, please notify the originator immediately. If you are not the intended recipient, you are notified that you are strictly prohibited from using, copying, altering, or disclosing the contents of this message. Aricent accepts no responsibility for loss or damage arising from the use of the information transmitted by this email including damage from virus."
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 6+ messages in thread
* Queries about ath10k driver and QCA988x based radio from sparklan
@ 2015-12-25 17:39 sunder
2015-12-28 13:01 ` Ankur Saxena
0 siblings, 1 reply; 6+ messages in thread
From: sunder @ 2015-12-25 17:39 UTC (permalink / raw)
To: ankur.saxena@sibridgetech.com, ath10k@lists.infradead.org
Use iw tool.
Best Regards,
Sunder
From: Ankur Saxena <ankur.saxena@sibridgetech.com>
Sent: Friday, December 25, 2015 5:49 PM
To: Sunder Kumaresan
Cc: ath10k@lists.infradead.org
Subject: Re: Queries about ath10k driver and QCA988x based radio from sparklan
Hi Sunder,
We have upgraded kernel to 4.4.0 version. Also updated firmware from git://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git for QCA988X. We are able to get up wlan0 in master mode and also able to see it on our client mobiles which supports 802.11ac with link speed 450Mbps. However iwconfig utility is not showind interface protocol as 802.11ac.
Does any one know whether iwconfig supports 802.11ac protocol information display as it looks like our radio is working as 802.11ac only?
Thanks,
Ankur Saxena
On Fri, Dec 25, 2015 at 5:40 PM, Sunder Kumaresan < sunder.kumaresan@aricent.com> wrote:
Did you update your firmware ?
https://wireless.wiki.kernel.org/en/users/drivers/ath10k/firmware
It worked for us in 3.18 Kernel
Use the above link.
Best Regards,
Sunder
________________________________________
From: ath10k <ath10k-bounces@lists.infradead.org> on behalf of Ankur Saxena <ankur.saxena@sibridgetech.com>
Sent: Friday, December 25, 2015 4:44 PM
To: ath10k@lists.infradead.org
Subject: Queries about ath10k driver and QCA988x based radio from sparklan
Hi All,
We have purchased radio module "WPEA-352ACN" from SparkLan. We are using
this radio module with ViaTech board for 802.11 AC functionality. We are
running linux kernel 3.19.1 with atheros driver ath10k up with all the
configuration elements.
We are facing some issues in getting up 802.11 AC functionality for the
radio. Please find below the queries:
1) We are using latest ath10k driver with 802.11AC configuration
enabled. On loading the driver for ath10k, we are not seeing "802.11AC"
in iwconfig utility for wlan interface. It is showing only 802.11 abgn
for the interface.
2) Tried to make AP using the interface by taking help of hostapd
utility. Searched on internet for configuration related to making 802.11
AC AP and used them all. In this case, Mode parameter in iwconfig is
changed to Master which shows AP functionality, but the interface is
still showing 802.11 abgn supported only.
3) We are using plain text version of regulatory database file (DB.txt)
which is maintained for use of CRDA. We are making sure that DB.txt file
is parsed properly and the database is added into MAC driver by parsing
the database file.
4) While running hostapd with full configuration for 802.11AC AP
settings, no error is seen for setting up the interface. Channel setting
is done for Auto-configuration and VHT settings are also applied in the
configuration file. The interface is not able to get up in 802.11 AC
mode, instead it is coming up only in 802.11 abgn only.
5) There is one error seen after firmware gets downloaded and starts
running. The error is as below:
ath10k_pci 0000:02:00.0: Direct firmware load for
ath10k/cal-pci-0000:02:00.0.bin failed with error -2
Can this may create this issue to happen also?
Please find attached the DB.txt and hostapd configuration file for
reference.
Can anyone please help us in getting 802.11 AC mode up and running in
the radio.
"DISCLAIMER: This message is proprietary to Aricent and is intended solely for the use of the individual to whom it is addressed. It may contain privileged or confidential information and should not be circulated or used for any purpose other than for what it is intended. If you have received this message in error, please notify the originator immediately. If you are not the intended recipient, you are notified that you are strictly prohibited from using, copying, altering, or disclosing the contents of this message. Aricent accepts no responsibility for loss or damage arising from the use of the information transmitted by this email including damage from virus."
--
Thanks and Regards,
Ankur Saxena.
Mobile: +91-8141197855.
MTS - Embedded Department
An Innovative Solutions Provider
ASIC | FPGA | Design & Verification IPs | Embedded Solutions
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Queries about ath10k driver and QCA988x based radio from sparklan
2015-12-25 17:39 sunder
@ 2015-12-28 13:01 ` Ankur Saxena
2015-12-29 5:51 ` Ankur Saxena
0 siblings, 1 reply; 6+ messages in thread
From: Ankur Saxena @ 2015-12-28 13:01 UTC (permalink / raw)
To: sunder; +Cc: ath10k@lists.infradead.org
On Friday 25 December 2015 11:09 PM, sunder wrote:
> Use iw tool.
>
>
>
> Best Regards,
>
> Sunder
>
>
>
> From: Ankur Saxena <ankur.saxena@sibridgetech.com>
> Sent: Friday, December 25, 2015 5:49 PM
> To: Sunder Kumaresan
> Cc: ath10k@lists.infradead.org
> Subject: Re: Queries about ath10k driver and QCA988x based radio from sparklan
>
>
>
>
> Hi Sunder,
>
>
>
> We have upgraded kernel to 4.4.0 version. Also updated firmware from git://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git for QCA988X. We are able to get up wlan0 in master mode and also able to see it on our client mobiles which supports 802.11ac with link speed 450Mbps. However iwconfig utility is not showind interface protocol as 802.11ac.
>
>
>
>
> Does any one know whether iwconfig supports 802.11ac protocol information display as it looks like our radio is working as 802.11ac only?
>
>
>
>
> Thanks,
>
> Ankur Saxena
>
>
>
>
>
>
> On Fri, Dec 25, 2015 at 5:40 PM, Sunder Kumaresan < sunder.kumaresan@aricent.com> wrote:
>
> Did you update your firmware ?
>
> https://wireless.wiki.kernel.org/en/users/drivers/ath10k/firmware
>
> It worked for us in 3.18 Kernel
>
> Use the above link.
>
> Best Regards,
> Sunder
>
>
> ________________________________________
> From: ath10k <ath10k-bounces@lists.infradead.org> on behalf of Ankur Saxena <ankur.saxena@sibridgetech.com>
> Sent: Friday, December 25, 2015 4:44 PM
> To: ath10k@lists.infradead.org
> Subject: Queries about ath10k driver and QCA988x based radio from sparklan
>
>
>
> Hi All,
>
> We have purchased radio module "WPEA-352ACN" from SparkLan. We are using
> this radio module with ViaTech board for 802.11 AC functionality. We are
> running linux kernel 3.19.1 with atheros driver ath10k up with all the
> configuration elements.
>
> We are facing some issues in getting up 802.11 AC functionality for the
> radio. Please find below the queries:
>
> 1) We are using latest ath10k driver with 802.11AC configuration
> enabled. On loading the driver for ath10k, we are not seeing "802.11AC"
> in iwconfig utility for wlan interface. It is showing only 802.11 abgn
> for the interface.
>
> 2) Tried to make AP using the interface by taking help of hostapd
> utility. Searched on internet for configuration related to making 802.11
> AC AP and used them all. In this case, Mode parameter in iwconfig is
> changed to Master which shows AP functionality, but the interface is
> still showing 802.11 abgn supported only.
>
> 3) We are using plain text version of regulatory database file (DB.txt)
> which is maintained for use of CRDA. We are making sure that DB.txt file
> is parsed properly and the database is added into MAC driver by parsing
> the database file.
>
> 4) While running hostapd with full configuration for 802.11AC AP
> settings, no error is seen for setting up the interface. Channel setting
> is done for Auto-configuration and VHT settings are also applied in the
> configuration file. The interface is not able to get up in 802.11 AC
> mode, instead it is coming up only in 802.11 abgn only.
>
> 5) There is one error seen after firmware gets downloaded and starts
> running. The error is as below:
> ath10k_pci 0000:02:00.0: Direct firmware load for
> ath10k/cal-pci-0000:02:00.0.bin failed with error -2
> Can this may create this issue to happen also?
>
> Please find attached the DB.txt and hostapd configuration file for
> reference.
>
> Can anyone please help us in getting 802.11 AC mode up and running in
> the radio.
>
>
> "DISCLAIMER: This message is proprietary to Aricent and is intended solely for the use of the individual to whom it is addressed. It may contain privileged or confidential information and should not be circulated or used for any purpose other than for what it is intended. If you have received this message in error, please notify the originator immediately. If you are not the intended recipient, you are notified that you are strictly prohibited from using, copying, altering, or disclosing the contents of this message. Aricent accepts no responsibility for loss or damage arising from the use of the information transmitted by this email including damage from virus."
>
>
>
>
>
Hi Sunder,
As in iwconfig we can use command "iwconfig wlan0" and can check the protocol used as 802.11 abgn. We have tried to use iw utility but there seems to be no command which gives information about the protocol
getting used in radio. We have checked iw list command which shows which channels are supporting which frequency and other info. Also we tried "iw dev wlan0 info" command which shows the MAC id, type and channel
information. Please help us in finding out whether our radio is configured in 802.11AC mode or not.
We have experimented more into this by making our radio as AP using hostapd as mentioned in previous mail. Here we found out that mobile devices supporting 802.11AC are the only devices which are able to see our
SSID. So now we applied static IP to AP and devices supporting 802.11AC and tried to check different things in there as mentioned below:
1)*Link speed:* with 3x3 MIMO 802.11AC radio card, I can see link speed of 780MBps on nexus 6p phone and 450MBps on htc one mobile device.
2)*Interface information:*
*a) 802.11ac dev info:*
root@Linux-> iw dev wlan0 info
Interface wlan0
ifindex 5
wdev 0x1
addr 00:0e:8e:57:70:63
ssid ath10k
type AP
wiphy 0
channel 52 (5260 MHz), width: 80 MHz, center1: 5290 MHz
So here channel is working on 80MHz i.e. it is reflected VHT capability is set to 80 in hostapd configuration.
*b) 802.11n dev info:*
root@Linux-> iw wlan0 info
Interface wlan0
ifindex 5
wdev 0x1
addr 00:0e:8e:57:70:63
ssid ath10k
type AP
wiphy 0
channel 157 (5785 MHz), width: 40 MHz, center1: 5795 MHz
So here channel is working on 40MHz i.e. it is reflected HT capability is set to 40 in hostapd configuration.
3)*Bandwidth calculation using iperf: TCP tx
a) 802.11AC: AP(3x3) (Client) -----> Nexus 6p(2x2) device (Server)
*
root@Linux-> iperf -c 10.10.0.4 -V -t 60
------------------------------------------------------------
Client connecting to 10.10.0.4, TCP port 5001
TCP window size: 43.8 KByte (default)
------------------------------------------------------------
[ 3] local 10.10.0.1 port 54458 connected with 10.10.0.4 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0-60.0 sec 1.23 GBytes* 176 Mbits/sec*
*b) 8**02.11AC: AP(3x3) (Client) -----> HTC ONE M7(1x1) device (Server)*
Same experiment was done with HTC one mobile device also and in that we got bandwidth of*140Mbits/sec*.
*c)* *802.11n: AP(3x3) (Client) -----> Nexus 6p(2x2) device (Server)*
root@Linux-> iperf -c 10.10.0.4 -t 60
------------------------------------------------------------
Client connecting to 10.10.0.4, TCP port 5001
TCP window size: 43.8 KByte (default)
------------------------------------------------------------
[ 3] local 10.10.0.1 port 54462 connected with 10.10.0.4 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0-60.0 sec 759 MBytes*106 Mbits/sec*
5) Should we consider that our radio is configured in 802.11AC mode?
Are these experiments going in right direction or can we verify the same using some other method also?
Are we getting correct throughput with these experiments as we have found some links where throughput has reached upto 250MBits/sec.
Thanks,
Ankur Saxena
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: Queries about ath10k driver and QCA988x based radio from sparklan
2015-12-28 13:01 ` Ankur Saxena
@ 2015-12-29 5:51 ` Ankur Saxena
2015-12-29 12:36 ` Sunder Kumaresan
0 siblings, 1 reply; 6+ messages in thread
From: Ankur Saxena @ 2015-12-29 5:51 UTC (permalink / raw)
To: sunder; +Cc: ath10k@lists.infradead.org
Hi Sunder,
As in iwconfig we can use command "iwconfig wlan0" and can check the
protocol used as 802.11 abgn. We have tried to use iw utility but there
seems to be no command which gives information about the protocol
getting used in radio. We have checked iw list command which shows which
channels are supporting which frequency and other info. Also we tried
"iw dev wlan0 info" command which shows the MAC id, type and channel
information. Please help us in finding out whether our radio is
configured in 802.11AC mode or not.
We have experimented more into this by making our radio as AP using
hostapd as mentioned in previous mail. Here we found out that mobile
devices supporting 802.11AC are the only devices which are able to see our
SSID. So now we applied static IP to AP and devices supporting 802.11AC
and tried to check different things in there as mentioned below:
1)*Link speed:* with 3x3 MIMO 802.11AC radio card, I can see link speed
of 780MBps on nexus 6p phone and 450MBps on htc one mobile device.
2)*Interface information:*
*a) 802.11ac dev info:*
root@Linux-> iw dev wlan0 info
Interface wlan0
ifindex 5
wdev 0x1
addr 00:0e:8e:57:70:63
ssid ath10k
type AP
wiphy 0
channel 52 (5260 MHz), width: 80 MHz, center1: 5290 MHz
So here channel is working on 80MHz i.e. it is reflected VHT capability
is set to 80 in hostapd configuration.
*b) 802.11n dev info:*
root@Linux-> iw wlan0 info
Interface wlan0
ifindex 5
wdev 0x1
addr 00:0e:8e:57:70:63
ssid ath10k
type AP
wiphy 0
channel 157 (5785 MHz), width: 40 MHz, center1: 5795 MHz
So here channel is working on 40MHz i.e. it is reflected HT capability
is set to 40 in hostapd configuration.
3)*Bandwidth calculation using iperf: TCP tx
a) 802.11AC: AP(3x3) (Client) -----> Nexus 6p(2x2) device (Server)
*
root@Linux-> iperf -c 10.10.0.4 -V -t 60
------------------------------------------------------------
Client connecting to 10.10.0.4, TCP port 5001
TCP window size: 43.8 KByte (default)
------------------------------------------------------------
[ 3] local 10.10.0.1 port 54458 connected with 10.10.0.4 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0-60.0 sec 1.23 GBytes* 176 Mbits/sec*
*b) 8**02.11AC: AP(3x3) (Client) -----> HTC ONE M7(1x1) device (Server)*
Same experiment was done with HTC one mobile device also and in that we
got bandwidth of*140Mbits/sec*.
*c)* *802.11n: AP(3x3) (Client) -----> Nexus 6p(2x2) device (Server)*
root@Linux-> iperf -c 10.10.0.4 -t 60
------------------------------------------------------------
Client connecting to 10.10.0.4, TCP port 5001
TCP window size: 43.8 KByte (default)
------------------------------------------------------------
[ 3] local 10.10.0.1 port 54462 connected with 10.10.0.4 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0-60.0 sec 759 MBytes*106 Mbits/sec*
5) Should we consider that our radio is configured in 802.11AC mode?
Are these experiments going in right direction or can we verify the same
using some other method also?
Are we getting correct throughput with these experiments as we have
found some links where throughput has reached upto 250MBits/sec.
Thanks,
Ankur Saxena
On Monday 28 December 2015 06:31 PM, Ankur Saxena wrote:
> On Friday 25 December 2015 11:09 PM, sunder wrote:
>> Use iw tool.
>>
>>
>>
>> Best Regards,
>>
>> Sunder
>>
>>
>>
>> From: Ankur Saxena <ankur.saxena@sibridgetech.com>
>> Sent: Friday, December 25, 2015 5:49 PM
>> To: Sunder Kumaresan
>> Cc: ath10k@lists.infradead.org
>> Subject: Re: Queries about ath10k driver and QCA988x based radio from
>> sparklan
>>
>>
>>
>> Hi Sunder,
>>
>>
>>
>> We have upgraded kernel to 4.4.0 version. Also updated firmware from
>> git://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git
>> for QCA988X. We are able to get up wlan0 in master mode and also able
>> to see it on our client mobiles which supports 802.11ac with link
>> speed 450Mbps. However iwconfig utility is not showind interface
>> protocol as 802.11ac.
>>
>>
>>
>>
>> Does any one know whether iwconfig supports 802.11ac protocol
>> information display as it looks like our radio is working as 802.11ac
>> only?
>>
>>
>>
>>
>> Thanks,
>>
>> Ankur Saxena
>>
>>
>>
>>
>>
>>
>> On Fri, Dec 25, 2015 at 5:40 PM, Sunder Kumaresan <
>> sunder.kumaresan@aricent.com> wrote:
>>
>> Did you update your firmware ?
>>
>> https://wireless.wiki.kernel.org/en/users/drivers/ath10k/firmware
>>
>> It worked for us in 3.18 Kernel
>>
>> Use the above link.
>>
>> Best Regards,
>> Sunder
>>
>>
>> ________________________________________
>> From: ath10k <ath10k-bounces@lists.infradead.org> on behalf of
>> Ankur Saxena <ankur.saxena@sibridgetech.com>
>> Sent: Friday, December 25, 2015 4:44 PM
>> To: ath10k@lists.infradead.org
>> Subject: Queries about ath10k driver and QCA988x based radio from
>> sparklan
>>
>>
>>
>> Hi All,
>>
>> We have purchased radio module "WPEA-352ACN" from SparkLan. We are using
>> this radio module with ViaTech board for 802.11 AC functionality.
>> We are
>> running linux kernel 3.19.1 with atheros driver ath10k up with all the
>> configuration elements.
>>
>> We are facing some issues in getting up 802.11 AC functionality for
>> the
>> radio. Please find below the queries:
>>
>> 1) We are using latest ath10k driver with 802.11AC configuration
>> enabled. On loading the driver for ath10k, we are not seeing
>> "802.11AC"
>> in iwconfig utility for wlan interface. It is showing only 802.11 abgn
>> for the interface.
>>
>> 2) Tried to make AP using the interface by taking help of hostapd
>> utility. Searched on internet for configuration related to making
>> 802.11
>> AC AP and used them all. In this case, Mode parameter in iwconfig is
>> changed to Master which shows AP functionality, but the interface is
>> still showing 802.11 abgn supported only.
>>
>> 3) We are using plain text version of regulatory database file
>> (DB.txt)
>> which is maintained for use of CRDA. We are making sure that DB.txt
>> file
>> is parsed properly and the database is added into MAC driver by
>> parsing
>> the database file.
>>
>> 4) While running hostapd with full configuration for 802.11AC AP
>> settings, no error is seen for setting up the interface. Channel
>> setting
>> is done for Auto-configuration and VHT settings are also applied in
>> the
>> configuration file. The interface is not able to get up in 802.11 AC
>> mode, instead it is coming up only in 802.11 abgn only.
>>
>> 5) There is one error seen after firmware gets downloaded and starts
>> running. The error is as below:
>> ath10k_pci 0000:02:00.0: Direct firmware load for
>> ath10k/cal-pci-0000:02:00.0.bin failed with error -2
>> Can this may create this issue to happen also?
>>
>> Please find attached the DB.txt and hostapd configuration file for
>> reference.
>>
>> Can anyone please help us in getting 802.11 AC mode up and running in
>> the radio.
>>
>>
>> "DISCLAIMER: This message is proprietary to Aricent and is intended
>> solely for the use of the individual to whom it is addressed. It may
>> contain privileged or confidential information and should not be
>> circulated or used for any purpose other than for what it is
>> intended. If you have received this message in error, please notify
>> the originator immediately. If you are not the intended recipient,
>> you are notified that you are strictly prohibited from using,
>> copying, altering, or disclosing the contents of this message.
>> Aricent accepts no responsibility for loss or damage arising from the
>> use of the information transmitted by this email including damage
>> from virus."
>>
>>
>>
>>
>>
> Hi Sunder,
>
> As in iwconfig we can use command "iwconfig wlan0" and can check the
> protocol used as 802.11 abgn. We have tried to use iw utility but
> there seems to be no command which gives information about the protocol
> getting used in radio. We have checked iw list command which shows
> which channels are supporting which frequency and other info. Also we
> tried "iw dev wlan0 info" command which shows the MAC id, type and
> channel
> information. Please help us in finding out whether our radio is
> configured in 802.11AC mode or not.
>
> We have experimented more into this by making our radio as AP using
> hostapd as mentioned in previous mail. Here we found out that mobile
> devices supporting 802.11AC are the only devices which are able to see
> our
> SSID. So now we applied static IP to AP and devices supporting
> 802.11AC and tried to check different things in there as mentioned below:
>
> 1)*Link speed:* with 3x3 MIMO 802.11AC radio card, I can see link
> speed of 780MBps on nexus 6p phone and 450MBps on htc one mobile device.
> 2)*Interface information:*
> *a) 802.11ac dev info:*
> root@Linux-> iw dev wlan0 info
>
> Interface wlan0
> ifindex 5
> wdev 0x1
> addr 00:0e:8e:57:70:63
> ssid ath10k
> type AP
> wiphy 0
> channel 52 (5260 MHz), width: 80 MHz, center1: 5290 MHz
>
> So here channel is working on 80MHz i.e. it is reflected VHT
> capability is set to 80 in hostapd configuration.
>
> *b) 802.11n dev info:*
> root@Linux-> iw wlan0 info
> Interface wlan0
> ifindex 5
> wdev 0x1
> addr 00:0e:8e:57:70:63
> ssid ath10k
> type AP
> wiphy 0
> channel 157 (5785 MHz), width: 40 MHz, center1: 5795 MHz
>
> So here channel is working on 40MHz i.e. it is reflected HT capability
> is set to 40 in hostapd configuration.
>
>
> 3)*Bandwidth calculation using iperf: TCP tx
> a) 802.11AC: AP(3x3) (Client) -----> Nexus 6p(2x2) device (Server)
> *
> root@Linux-> iperf -c 10.10.0.4 -V -t 60
> ------------------------------------------------------------
> Client connecting to 10.10.0.4, TCP port 5001
> TCP window size: 43.8 KByte (default)
> ------------------------------------------------------------
> [ 3] local 10.10.0.1 port 54458 connected with 10.10.0.4 port 5001
> [ ID] Interval Transfer Bandwidth
> [ 3] 0.0-60.0 sec 1.23 GBytes* 176 Mbits/sec*
>
> *b) 8**02.11AC: AP(3x3) (Client) -----> HTC ONE M7(1x1) device (Server)*
> Same experiment was done with HTC one mobile device also and in that
> we got bandwidth of*140Mbits/sec*.
>
> *c)* *802.11n: AP(3x3) (Client) -----> Nexus 6p(2x2) device (Server)*
>
> root@Linux-> iperf -c 10.10.0.4 -t 60
> ------------------------------------------------------------
> Client connecting to 10.10.0.4, TCP port 5001
> TCP window size: 43.8 KByte (default)
> ------------------------------------------------------------
> [ 3] local 10.10.0.1 port 54462 connected with 10.10.0.4 port 5001
> [ ID] Interval Transfer Bandwidth
> [ 3] 0.0-60.0 sec 759 MBytes*106 Mbits/sec*
>
>
> 5) Should we consider that our radio is configured in 802.11AC mode?
> Are these experiments going in right direction or can we verify the
> same using some other method also?
> Are we getting correct throughput with these experiments as we have
> found some links where throughput has reached upto 250MBits/sec.
>
> Thanks,
> Ankur Saxena
>
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 6+ messages in thread
* RE: Queries about ath10k driver and QCA988x based radio from sparklan
2015-12-29 5:51 ` Ankur Saxena
@ 2015-12-29 12:36 ` Sunder Kumaresan
0 siblings, 0 replies; 6+ messages in thread
From: Sunder Kumaresan @ 2015-12-29 12:36 UTC (permalink / raw)
To: Ankur Saxena, sunder; +Cc: ath10k@lists.infradead.org
Use iw phy phy0 info.
Max throughput info were published with control environment results.
Best Regards,
,k.sunder
-----Original Message-----
From: ath10k [mailto:ath10k-bounces@lists.infradead.org] On Behalf Of Ankur Saxena
Sent: Tuesday, December 29, 2015 11:22 AM
To: sunder <sunder_k@hotmail.com>
Cc: ath10k@lists.infradead.org
Subject: Re: Queries about ath10k driver and QCA988x based radio from sparklan
Hi Sunder,
As in iwconfig we can use command "iwconfig wlan0" and can check the protocol used as 802.11 abgn. We have tried to use iw utility but there seems to be no command which gives information about the protocol getting used in radio. We have checked iw list command which shows which channels are supporting which frequency and other info. Also we tried "iw dev wlan0 info" command which shows the MAC id, type and channel information. Please help us in finding out whether our radio is configured in 802.11AC mode or not.
We have experimented more into this by making our radio as AP using hostapd as mentioned in previous mail. Here we found out that mobile devices supporting 802.11AC are the only devices which are able to see our SSID. So now we applied static IP to AP and devices supporting 802.11AC and tried to check different things in there as mentioned below:
1)*Link speed:* with 3x3 MIMO 802.11AC radio card, I can see link speed of 780MBps on nexus 6p phone and 450MBps on htc one mobile device.
2)*Interface information:*
*a) 802.11ac dev info:*
root@Linux-> iw dev wlan0 info
Interface wlan0
ifindex 5
wdev 0x1
addr 00:0e:8e:57:70:63
ssid ath10k
type AP
wiphy 0
channel 52 (5260 MHz), width: 80 MHz, center1: 5290 MHz
So here channel is working on 80MHz i.e. it is reflected VHT capability is set to 80 in hostapd configuration.
*b) 802.11n dev info:*
root@Linux-> iw wlan0 info
Interface wlan0
ifindex 5
wdev 0x1
addr 00:0e:8e:57:70:63
ssid ath10k
type AP
wiphy 0
channel 157 (5785 MHz), width: 40 MHz, center1: 5795 MHz
So here channel is working on 40MHz i.e. it is reflected HT capability is set to 40 in hostapd configuration.
3)*Bandwidth calculation using iperf: TCP tx
a) 802.11AC: AP(3x3) (Client) -----> Nexus 6p(2x2) device (Server)
*
root@Linux-> iperf -c 10.10.0.4 -V -t 60
------------------------------------------------------------
Client connecting to 10.10.0.4, TCP port 5001
TCP window size: 43.8 KByte (default)
------------------------------------------------------------
[ 3] local 10.10.0.1 port 54458 connected with 10.10.0.4 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0-60.0 sec 1.23 GBytes* 176 Mbits/sec*
*b) 8**02.11AC: AP(3x3) (Client) -----> HTC ONE M7(1x1) device (Server)*
Same experiment was done with HTC one mobile device also and in that we
got bandwidth of*140Mbits/sec*.
*c)* *802.11n: AP(3x3) (Client) -----> Nexus 6p(2x2) device (Server)*
root@Linux-> iperf -c 10.10.0.4 -t 60
------------------------------------------------------------
Client connecting to 10.10.0.4, TCP port 5001
TCP window size: 43.8 KByte (default)
------------------------------------------------------------
[ 3] local 10.10.0.1 port 54462 connected with 10.10.0.4 port 5001
[ ID] Interval Transfer Bandwidth
[ 3] 0.0-60.0 sec 759 MBytes*106 Mbits/sec*
5) Should we consider that our radio is configured in 802.11AC mode?
Are these experiments going in right direction or can we verify the same
using some other method also?
Are we getting correct throughput with these experiments as we have
found some links where throughput has reached upto 250MBits/sec.
Thanks,
Ankur Saxena
On Monday 28 December 2015 06:31 PM, Ankur Saxena wrote:
> On Friday 25 December 2015 11:09 PM, sunder wrote:
>> Use iw tool.
>>
>>
>>
>> Best Regards,
>>
>> Sunder
>>
>>
>>
>> From: Ankur Saxena <ankur.saxena@sibridgetech.com>
>> Sent: Friday, December 25, 2015 5:49 PM
>> To: Sunder Kumaresan
>> Cc: ath10k@lists.infradead.org
>> Subject: Re: Queries about ath10k driver and QCA988x based radio from
>> sparklan
>>
>>
>>
>> Hi Sunder,
>>
>>
>>
>> We have upgraded kernel to 4.4.0 version. Also updated firmware from
>> git://git.kernel.org/pub/scm/linux/kernel/git/firmware/linux-firmware.git
>> for QCA988X. We are able to get up wlan0 in master mode and also able
>> to see it on our client mobiles which supports 802.11ac with link
>> speed 450Mbps. However iwconfig utility is not showind interface
>> protocol as 802.11ac.
>>
>>
>>
>>
>> Does any one know whether iwconfig supports 802.11ac protocol
>> information display as it looks like our radio is working as 802.11ac
>> only?
>>
>>
>>
>>
>> Thanks,
>>
>> Ankur Saxena
>>
>>
>>
>>
>>
>>
>> On Fri, Dec 25, 2015 at 5:40 PM, Sunder Kumaresan <
>> sunder.kumaresan@aricent.com> wrote:
>>
>> Did you update your firmware ?
>>
>> https://wireless.wiki.kernel.org/en/users/drivers/ath10k/firmware
>>
>> It worked for us in 3.18 Kernel
>>
>> Use the above link.
>>
>> Best Regards,
>> Sunder
>>
>>
>> ________________________________________
>> From: ath10k <ath10k-bounces@lists.infradead.org> on behalf of
>> Ankur Saxena <ankur.saxena@sibridgetech.com>
>> Sent: Friday, December 25, 2015 4:44 PM
>> To: ath10k@lists.infradead.org
>> Subject: Queries about ath10k driver and QCA988x based radio from
>> sparklan
>>
>>
>>
>> Hi All,
>>
>> We have purchased radio module "WPEA-352ACN" from SparkLan. We are using
>> this radio module with ViaTech board for 802.11 AC functionality.
>> We are
>> running linux kernel 3.19.1 with atheros driver ath10k up with all the
>> configuration elements.
>>
>> We are facing some issues in getting up 802.11 AC functionality for
>> the
>> radio. Please find below the queries:
>>
>> 1) We are using latest ath10k driver with 802.11AC configuration
>> enabled. On loading the driver for ath10k, we are not seeing
>> "802.11AC"
>> in iwconfig utility for wlan interface. It is showing only 802.11 abgn
>> for the interface.
>>
>> 2) Tried to make AP using the interface by taking help of hostapd
>> utility. Searched on internet for configuration related to making
>> 802.11
>> AC AP and used them all. In this case, Mode parameter in iwconfig is
>> changed to Master which shows AP functionality, but the interface is
>> still showing 802.11 abgn supported only.
>>
>> 3) We are using plain text version of regulatory database file
>> (DB.txt)
>> which is maintained for use of CRDA. We are making sure that DB.txt
>> file
>> is parsed properly and the database is added into MAC driver by
>> parsing
>> the database file.
>>
>> 4) While running hostapd with full configuration for 802.11AC AP
>> settings, no error is seen for setting up the interface. Channel
>> setting
>> is done for Auto-configuration and VHT settings are also applied in
>> the
>> configuration file. The interface is not able to get up in 802.11 AC
>> mode, instead it is coming up only in 802.11 abgn only.
>>
>> 5) There is one error seen after firmware gets downloaded and starts
>> running. The error is as below:
>> ath10k_pci 0000:02:00.0: Direct firmware load for
>> ath10k/cal-pci-0000:02:00.0.bin failed with error -2
>> Can this may create this issue to happen also?
>>
>> Please find attached the DB.txt and hostapd configuration file for
>> reference.
>>
>> Can anyone please help us in getting 802.11 AC mode up and running in
>> the radio.
>>
>>
>> "DISCLAIMER: This message is proprietary to Aricent and is intended
>> solely for the use of the individual to whom it is addressed. It may
>> contain privileged or confidential information and should not be
>> circulated or used for any purpose other than for what it is
>> intended. If you have received this message in error, please notify
>> the originator immediately. If you are not the intended recipient,
>> you are notified that you are strictly prohibited from using,
>> copying, altering, or disclosing the contents of this message.
>> Aricent accepts no responsibility for loss or damage arising from the
>> use of the information transmitted by this email including damage
>> from virus."
>>
>>
>>
>>
>>
> Hi Sunder,
>
> As in iwconfig we can use command "iwconfig wlan0" and can check the
> protocol used as 802.11 abgn. We have tried to use iw utility but
> there seems to be no command which gives information about the protocol
> getting used in radio. We have checked iw list command which shows
> which channels are supporting which frequency and other info. Also we
> tried "iw dev wlan0 info" command which shows the MAC id, type and
> channel
> information. Please help us in finding out whether our radio is
> configured in 802.11AC mode or not.
>
> We have experimented more into this by making our radio as AP using
> hostapd as mentioned in previous mail. Here we found out that mobile
> devices supporting 802.11AC are the only devices which are able to see
> our
> SSID. So now we applied static IP to AP and devices supporting
> 802.11AC and tried to check different things in there as mentioned below:
>
> 1)*Link speed:* with 3x3 MIMO 802.11AC radio card, I can see link
> speed of 780MBps on nexus 6p phone and 450MBps on htc one mobile device.
> 2)*Interface information:*
> *a) 802.11ac dev info:*
> root@Linux-> iw dev wlan0 info
>
> Interface wlan0
> ifindex 5
> wdev 0x1
> addr 00:0e:8e:57:70:63
> ssid ath10k
> type AP
> wiphy 0
> channel 52 (5260 MHz), width: 80 MHz, center1: 5290 MHz
>
> So here channel is working on 80MHz i.e. it is reflected VHT
> capability is set to 80 in hostapd configuration.
>
> *b) 802.11n dev info:*
> root@Linux-> iw wlan0 info
> Interface wlan0
> ifindex 5
> wdev 0x1
> addr 00:0e:8e:57:70:63
> ssid ath10k
> type AP
> wiphy 0
> channel 157 (5785 MHz), width: 40 MHz, center1: 5795 MHz
>
> So here channel is working on 40MHz i.e. it is reflected HT capability
> is set to 40 in hostapd configuration.
>
>
> 3)*Bandwidth calculation using iperf: TCP tx
> a) 802.11AC: AP(3x3) (Client) -----> Nexus 6p(2x2) device (Server)
> *
> root@Linux-> iperf -c 10.10.0.4 -V -t 60
> ------------------------------------------------------------
> Client connecting to 10.10.0.4, TCP port 5001
> TCP window size: 43.8 KByte (default)
> ------------------------------------------------------------
> [ 3] local 10.10.0.1 port 54458 connected with 10.10.0.4 port 5001
> [ ID] Interval Transfer Bandwidth
> [ 3] 0.0-60.0 sec 1.23 GBytes* 176 Mbits/sec*
>
> *b) 8**02.11AC: AP(3x3) (Client) -----> HTC ONE M7(1x1) device (Server)*
> Same experiment was done with HTC one mobile device also and in that
> we got bandwidth of*140Mbits/sec*.
>
> *c)* *802.11n: AP(3x3) (Client) -----> Nexus 6p(2x2) device (Server)*
>
> root@Linux-> iperf -c 10.10.0.4 -t 60
> ------------------------------------------------------------
> Client connecting to 10.10.0.4, TCP port 5001
> TCP window size: 43.8 KByte (default)
> ------------------------------------------------------------
> [ 3] local 10.10.0.1 port 54462 connected with 10.10.0.4 port 5001
> [ ID] Interval Transfer Bandwidth
> [ 3] 0.0-60.0 sec 759 MBytes*106 Mbits/sec*
>
>
> 5) Should we consider that our radio is configured in 802.11AC mode?
> Are these experiments going in right direction or can we verify the
> same using some other method also?
> Are we getting correct throughput with these experiments as we have
> found some links where throughput has reached upto 250MBits/sec.
>
> Thanks,
> Ankur Saxena
>
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
"DISCLAIMER: This message is proprietary to Aricent and is intended solely for the use of the individual to whom it is addressed. It may contain privileged or confidential information and should not be circulated or used for any purpose other than for what it is intended. If you have received this message in error, please notify the originator immediately. If you are not the intended recipient, you are notified that you are strictly prohibited from using, copying, altering, or disclosing the contents of this message. Aricent accepts no responsibility for loss or damage arising from the use of the information transmitted by this email including damage from virus."
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2015-12-29 12:36 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2015-12-25 11:14 Queries about ath10k driver and QCA988x based radio from sparklan Ankur Saxena
2015-12-25 12:10 ` Sunder Kumaresan
-- strict thread matches above, loose matches on Subject: below --
2015-12-25 17:39 sunder
2015-12-28 13:01 ` Ankur Saxena
2015-12-29 5:51 ` Ankur Saxena
2015-12-29 12:36 ` Sunder Kumaresan
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.