[PATCH 0/5] ath10k: add basic hostq support

[PATCH 0/5] ath10k: add basic hostq support

[Michal Kazior]

There's a new firmware feature which uses a shared
DMA memory so host can share it's per-sta per-tid
queue size which is then subsequently used for
firmware to assist in deciding which frames to put
on the intermediate host-device tx queue.

This patchset adds only basic support to make
the firmware supporting the feature happy and
running at all. Without it firmware would freeze
shortly after booting.

More patches will follow some time later to add
the "new data path" logic.


Michal Kazior (5):
  ath10k: rename some HTT events
  ath10k: add new htt definitions
  ath10k: add new FW_FEATURE_PEER_FLOW_CONTROL
  ath10k: clean up cont frag desc init code
  ath10k: implement basic support for new tx path firmware

 drivers/net/wireless/ath/ath10k/core.c   |   1 +
 drivers/net/wireless/ath/ath10k/core.h   |   9 ++
 drivers/net/wireless/ath/ath10k/htt.c    |   8 +-
 drivers/net/wireless/ath/ath10k/htt.h    | 169 +++++++++++++++++++++++++++++--
 drivers/net/wireless/ath/ath10k/htt_rx.c |   8 +-
 drivers/net/wireless/ath/ath10k/htt_tx.c | 146 +++++++++++++++++++++-----
 6 files changed, 302 insertions(+), 39 deletions(-)

-- 
2.1.4


_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k

[PATCH 0/5] ath10k: add basic hostq support

[Michal Kazior]

There's a new firmware feature which uses a shared
DMA memory so host can share it's per-sta per-tid
queue size which is then subsequently used for
firmware to assist in deciding which frames to put
on the intermediate host-device tx queue.

This patchset adds only basic support to make
the firmware supporting the feature happy and
running at all. Without it firmware would freeze
shortly after booting.

More patches will follow some time later to add
the "new data path" logic.


Michal Kazior (5):
  ath10k: rename some HTT events
  ath10k: add new htt definitions
  ath10k: add new FW_FEATURE_PEER_FLOW_CONTROL
  ath10k: clean up cont frag desc init code
  ath10k: implement basic support for new tx path firmware

 drivers/net/wireless/ath/ath10k/core.c   |   1 +
 drivers/net/wireless/ath/ath10k/core.h   |   9 ++
 drivers/net/wireless/ath/ath10k/htt.c    |   8 +-
 drivers/net/wireless/ath/ath10k/htt.h    | 169 +++++++++++++++++++++++++++++--
 drivers/net/wireless/ath/ath10k/htt_rx.c |   8 +-
 drivers/net/wireless/ath/ath10k/htt_tx.c | 146 +++++++++++++++++++++-----
 6 files changed, 302 insertions(+), 39 deletions(-)

-- 
2.1.4

[PATCH 1/5] ath10k: rename some HTT events

[Michal Kazior]

New names make a bit more sense.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
---
 drivers/net/wireless/ath/ath10k/htt.c    | 8 ++++----
 drivers/net/wireless/ath/ath10k/htt.h    | 8 ++++----
 drivers/net/wireless/ath/ath10k/htt_rx.c | 4 ++--
 3 files changed, 10 insertions(+), 10 deletions(-)

diff --git a/drivers/net/wireless/ath/ath10k/htt.c b/drivers/net/wireless/ath/ath10k/htt.c
index 3e6ba63dfdff..7561f22f10f9 100644
--- a/drivers/net/wireless/ath/ath10k/htt.c
+++ b/drivers/net/wireless/ath/ath10k/htt.c
@@ -131,12 +131,12 @@ static const enum htt_t2h_msg_type htt_10_4_t2h_msg_types[] = {
 	[HTT_10_4_T2H_MSG_TYPE_AGGR_CONF] = HTT_T2H_MSG_TYPE_AGGR_CONF,
 	[HTT_10_4_T2H_MSG_TYPE_TX_FETCH_IND] =
 				HTT_T2H_MSG_TYPE_TX_FETCH_IND,
-	[HTT_10_4_T2H_MSG_TYPE_TX_FETCH_CONF] =
-				HTT_T2H_MSG_TYPE_TX_FETCH_CONF,
+	[HTT_10_4_T2H_MSG_TYPE_TX_FETCH_CONFIRM] =
+				HTT_T2H_MSG_TYPE_TX_FETCH_CONFIRM,
 	[HTT_10_4_T2H_MSG_TYPE_STATS_NOUPLOAD] =
 				HTT_T2H_MSG_TYPE_STATS_NOUPLOAD,
-	[HTT_10_4_T2H_MSG_TYPE_TX_LOW_LATENCY_IND] =
-				HTT_T2H_MSG_TYPE_TX_LOW_LATENCY_IND,
+	[HTT_10_4_T2H_MSG_TYPE_TX_MODE_SWITCH_IND] =
+				HTT_T2H_MSG_TYPE_TX_MODE_SWITCH_IND,
 };
 
 int ath10k_htt_connect(struct ath10k_htt *htt)
diff --git a/drivers/net/wireless/ath/ath10k/htt.h b/drivers/net/wireless/ath/ath10k/htt.h
index 47ca048feaf0..edd3b9070de9 100644
--- a/drivers/net/wireless/ath/ath10k/htt.h
+++ b/drivers/net/wireless/ath/ath10k/htt.h
@@ -413,10 +413,10 @@ enum htt_10_4_t2h_msg_type {
 	HTT_10_4_T2H_MSG_TYPE_EN_STATS               = 0x14,
 	HTT_10_4_T2H_MSG_TYPE_AGGR_CONF              = 0x15,
 	HTT_10_4_T2H_MSG_TYPE_TX_FETCH_IND           = 0x16,
-	HTT_10_4_T2H_MSG_TYPE_TX_FETCH_CONF          = 0x17,
+	HTT_10_4_T2H_MSG_TYPE_TX_FETCH_CONFIRM       = 0x17,
 	HTT_10_4_T2H_MSG_TYPE_STATS_NOUPLOAD         = 0x18,
 	/* 0x19 to 0x2f are reserved */
-	HTT_10_4_T2H_MSG_TYPE_TX_LOW_LATENCY_IND     = 0x30,
+	HTT_10_4_T2H_MSG_TYPE_TX_MODE_SWITCH_IND     = 0x30,
 	/* keep this last */
 	HTT_10_4_T2H_NUM_MSGS
 };
@@ -449,8 +449,8 @@ enum htt_t2h_msg_type {
 	HTT_T2H_MSG_TYPE_TEST,
 	HTT_T2H_MSG_TYPE_EN_STATS,
 	HTT_T2H_MSG_TYPE_TX_FETCH_IND,
-	HTT_T2H_MSG_TYPE_TX_FETCH_CONF,
-	HTT_T2H_MSG_TYPE_TX_LOW_LATENCY_IND,
+	HTT_T2H_MSG_TYPE_TX_FETCH_CONFIRM,
+	HTT_T2H_MSG_TYPE_TX_MODE_SWITCH_IND,
 	/* keep this last */
 	HTT_T2H_NUM_MSGS
 };
diff --git a/drivers/net/wireless/ath/ath10k/htt_rx.c b/drivers/net/wireless/ath/ath10k/htt_rx.c
index 91afa3ae414c..d923f64e4f42 100644
--- a/drivers/net/wireless/ath/ath10k/htt_rx.c
+++ b/drivers/net/wireless/ath/ath10k/htt_rx.c
@@ -2125,8 +2125,8 @@ void ath10k_htt_t2h_msg_handler(struct ath10k *ar, struct sk_buff *skb)
 		break;
 	case HTT_T2H_MSG_TYPE_EN_STATS:
 	case HTT_T2H_MSG_TYPE_TX_FETCH_IND:
-	case HTT_T2H_MSG_TYPE_TX_FETCH_CONF:
-	case HTT_T2H_MSG_TYPE_TX_LOW_LATENCY_IND:
+	case HTT_T2H_MSG_TYPE_TX_FETCH_CONFIRM:
+	case HTT_T2H_MSG_TYPE_TX_MODE_SWITCH_IND:
 	default:
 		ath10k_warn(ar, "htt event (%d) not handled\n",
 			    resp->hdr.msg_type);
-- 
2.1.4


_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k

[PATCH 1/5] ath10k: rename some HTT events

[Michal Kazior]

New names make a bit more sense.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
---
 drivers/net/wireless/ath/ath10k/htt.c    | 8 ++++----
 drivers/net/wireless/ath/ath10k/htt.h    | 8 ++++----
 drivers/net/wireless/ath/ath10k/htt_rx.c | 4 ++--
 3 files changed, 10 insertions(+), 10 deletions(-)

diff --git a/drivers/net/wireless/ath/ath10k/htt.c b/drivers/net/wireless/ath/ath10k/htt.c
index 3e6ba63dfdff..7561f22f10f9 100644
--- a/drivers/net/wireless/ath/ath10k/htt.c
+++ b/drivers/net/wireless/ath/ath10k/htt.c
@@ -131,12 +131,12 @@ static const enum htt_t2h_msg_type htt_10_4_t2h_msg_types[] = {
 	[HTT_10_4_T2H_MSG_TYPE_AGGR_CONF] = HTT_T2H_MSG_TYPE_AGGR_CONF,
 	[HTT_10_4_T2H_MSG_TYPE_TX_FETCH_IND] =
 				HTT_T2H_MSG_TYPE_TX_FETCH_IND,
-	[HTT_10_4_T2H_MSG_TYPE_TX_FETCH_CONF] =
-				HTT_T2H_MSG_TYPE_TX_FETCH_CONF,
+	[HTT_10_4_T2H_MSG_TYPE_TX_FETCH_CONFIRM] =
+				HTT_T2H_MSG_TYPE_TX_FETCH_CONFIRM,
 	[HTT_10_4_T2H_MSG_TYPE_STATS_NOUPLOAD] =
 				HTT_T2H_MSG_TYPE_STATS_NOUPLOAD,
-	[HTT_10_4_T2H_MSG_TYPE_TX_LOW_LATENCY_IND] =
-				HTT_T2H_MSG_TYPE_TX_LOW_LATENCY_IND,
+	[HTT_10_4_T2H_MSG_TYPE_TX_MODE_SWITCH_IND] =
+				HTT_T2H_MSG_TYPE_TX_MODE_SWITCH_IND,
 };
 
 int ath10k_htt_connect(struct ath10k_htt *htt)
diff --git a/drivers/net/wireless/ath/ath10k/htt.h b/drivers/net/wireless/ath/ath10k/htt.h
index 47ca048feaf0..edd3b9070de9 100644
--- a/drivers/net/wireless/ath/ath10k/htt.h
+++ b/drivers/net/wireless/ath/ath10k/htt.h
@@ -413,10 +413,10 @@ enum htt_10_4_t2h_msg_type {
 	HTT_10_4_T2H_MSG_TYPE_EN_STATS               = 0x14,
 	HTT_10_4_T2H_MSG_TYPE_AGGR_CONF              = 0x15,
 	HTT_10_4_T2H_MSG_TYPE_TX_FETCH_IND           = 0x16,
-	HTT_10_4_T2H_MSG_TYPE_TX_FETCH_CONF          = 0x17,
+	HTT_10_4_T2H_MSG_TYPE_TX_FETCH_CONFIRM       = 0x17,
 	HTT_10_4_T2H_MSG_TYPE_STATS_NOUPLOAD         = 0x18,
 	/* 0x19 to 0x2f are reserved */
-	HTT_10_4_T2H_MSG_TYPE_TX_LOW_LATENCY_IND     = 0x30,
+	HTT_10_4_T2H_MSG_TYPE_TX_MODE_SWITCH_IND     = 0x30,
 	/* keep this last */
 	HTT_10_4_T2H_NUM_MSGS
 };
@@ -449,8 +449,8 @@ enum htt_t2h_msg_type {
 	HTT_T2H_MSG_TYPE_TEST,
 	HTT_T2H_MSG_TYPE_EN_STATS,
 	HTT_T2H_MSG_TYPE_TX_FETCH_IND,
-	HTT_T2H_MSG_TYPE_TX_FETCH_CONF,
-	HTT_T2H_MSG_TYPE_TX_LOW_LATENCY_IND,
+	HTT_T2H_MSG_TYPE_TX_FETCH_CONFIRM,
+	HTT_T2H_MSG_TYPE_TX_MODE_SWITCH_IND,
 	/* keep this last */
 	HTT_T2H_NUM_MSGS
 };
diff --git a/drivers/net/wireless/ath/ath10k/htt_rx.c b/drivers/net/wireless/ath/ath10k/htt_rx.c
index 91afa3ae414c..d923f64e4f42 100644
--- a/drivers/net/wireless/ath/ath10k/htt_rx.c
+++ b/drivers/net/wireless/ath/ath10k/htt_rx.c
@@ -2125,8 +2125,8 @@ void ath10k_htt_t2h_msg_handler(struct ath10k *ar, struct sk_buff *skb)
 		break;
 	case HTT_T2H_MSG_TYPE_EN_STATS:
 	case HTT_T2H_MSG_TYPE_TX_FETCH_IND:
-	case HTT_T2H_MSG_TYPE_TX_FETCH_CONF:
-	case HTT_T2H_MSG_TYPE_TX_LOW_LATENCY_IND:
+	case HTT_T2H_MSG_TYPE_TX_FETCH_CONFIRM:
+	case HTT_T2H_MSG_TYPE_TX_MODE_SWITCH_IND:
 	default:
 		ath10k_warn(ar, "htt event (%d) not handled\n",
 			    resp->hdr.msg_type);
-- 
2.1.4

[PATCH 2/5] ath10k: add new htt definitions

[Michal Kazior]

These definitions are associated with some
improvements upcomming for 10.4 and QCA99X0.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
---
 drivers/net/wireless/ath/ath10k/htt.h | 153 +++++++++++++++++++++++++++++++++-
 1 file changed, 150 insertions(+), 3 deletions(-)

diff --git a/drivers/net/wireless/ath/ath10k/htt.h b/drivers/net/wireless/ath/ath10k/htt.h
index edd3b9070de9..0c5628dafabf 100644
--- a/drivers/net/wireless/ath/ath10k/htt.h
+++ b/drivers/net/wireless/ath/ath10k/htt.h
@@ -52,6 +52,7 @@ enum htt_h2t_msg_type { /* host-to-target */
 	/* This command is used for sending management frames in HTT < 3.0.
 	 * HTT >= 3.0 uses TX_FRM for everything. */
 	HTT_H2T_MSG_TYPE_MGMT_TX            = 7,
+	HTT_H2T_MSG_TYPE_TX_FETCH_RESP      = 11,
 
 	HTT_H2T_NUM_MSGS /* keep this last */
 };
@@ -1306,9 +1307,43 @@ struct htt_frag_desc_bank_id {
  * so we use a conservatively safe value for now */
 #define HTT_FRAG_DESC_BANK_MAX 4
 
-#define HTT_FRAG_DESC_BANK_CFG_INFO_PDEV_ID_MASK 0x03
-#define HTT_FRAG_DESC_BANK_CFG_INFO_PDEV_ID_LSB  0
-#define HTT_FRAG_DESC_BANK_CFG_INFO_SWAP         (1 << 2)
+#define HTT_FRAG_DESC_BANK_CFG_INFO_PDEV_ID_MASK		0x03
+#define HTT_FRAG_DESC_BANK_CFG_INFO_PDEV_ID_LSB			0
+#define HTT_FRAG_DESC_BANK_CFG_INFO_SWAP			BIT(2)
+#define HTT_FRAG_DESC_BANK_CFG_INFO_Q_STATE_VALID		BIT(3)
+#define HTT_FRAG_DESC_BANK_CFG_INFO_Q_STATE_DEPTH_TYPE_MASK	BIT(4)
+#define HTT_FRAG_DESC_BANK_CFG_INFO_Q_STATE_DEPTH_TYPE_LSB	4
+
+enum htt_q_depth_type {
+	HTT_Q_DEPTH_TYPE_BYTES = 0,
+	HTT_Q_DEPTH_TYPE_MSDUS = 1,
+};
+
+#define HTT_TX_Q_STATE_NUM_PEERS		(TARGET_10_4_NUM_QCACHE_PEERS_MAX + \
+						 TARGET_10_4_NUM_VDEVS)
+#define HTT_TX_Q_STATE_NUM_TIDS			8
+#define HTT_TX_Q_STATE_ENTRY_SIZE		1
+#define HTT_TX_Q_STATE_ENTRY_MULTIPLIER		0
+
+/**
+ * htt_q_state_conf - part of htt_frag_desc_bank_cfg for host q state config
+ *
+ * Defines host q state format and behavior. See htt_q_state.
+ *
+ * @record_size: Defines the size of each host q entry in bytes. In practice
+ *	however firmware (at least 10.4.3-00191) ignores this host
+ *	configuration value and uses hardcoded value of 1.
+ * @record_multiplier: This is valid only when q depth type is MSDUs. It
+ *	defines the exponent for the power of 2 multiplication.
+ */
+struct htt_q_state_conf {
+	__le32 paddr;
+	__le16 num_peers;
+	__le16 num_tids;
+	u8 record_size;
+	u8 record_multiplier;
+	u8 pad[2];
+} __packed;
 
 struct htt_frag_desc_bank_cfg {
 	u8 info; /* HTT_FRAG_DESC_BANK_CFG_INFO_ */
@@ -1316,6 +1351,114 @@ struct htt_frag_desc_bank_cfg {
 	u8 desc_size;
 	__le32 bank_base_addrs[HTT_FRAG_DESC_BANK_MAX];
 	struct htt_frag_desc_bank_id bank_id[HTT_FRAG_DESC_BANK_MAX];
+	struct htt_q_state_conf q_state;
+} __packed;
+
+#define HTT_TX_Q_STATE_ENTRY_COEFFICIENT	128
+#define HTT_TX_Q_STATE_ENTRY_FACTOR_MASK	0x3f
+#define HTT_TX_Q_STATE_ENTRY_FACTOR_LSB		0
+#define HTT_TX_Q_STATE_ENTRY_EXP_MASK		0xc0
+#define HTT_TX_Q_STATE_ENTRY_EXP_LSB		6
+
+/**
+ * htt_q_state - shared between host and firmware via DMA
+ *
+ * This structure is used for the host to expose it's software queue state to
+ * firmware so that its rate control can schedule fetch requests for optimized
+ * performance. This is most notably used for MU-MIMO aggregation when multiple
+ * MU clients are connected.
+ *
+ * @count: Each element defines the host queue depth. When q depth type was
+ *	configured as HTT_Q_DEPTH_TYPE_BYTES then each entry is defined as:
+ *	FACTOR * 128 * 8^EXP (see HTT_TX_Q_STATE_ENTRY_FACTOR_MASK and
+ *	HTT_TX_Q_STATE_ENTRY_EXP_MASK). When q depth type was configured as
+ *	HTT_Q_DEPTH_TYPE_MSDUS the number of packets is scaled by 2 **
+ *	record_multiplier (see htt_q_state_conf).
+ * @map: Used by firmware to quickly check which host queues are not empty. It
+ *	is a bitmap simply saying.
+ * @seq: Used by firmware to quickly check if the host queues were updated
+ *	since it last checked.
+ *
+ * FIXME: Is the q_state map[] size calculation really correct?
+ */
+struct htt_q_state {
+	u8 count[HTT_TX_Q_STATE_NUM_TIDS][HTT_TX_Q_STATE_NUM_PEERS];
+	u32 map[HTT_TX_Q_STATE_NUM_TIDS][(HTT_TX_Q_STATE_NUM_PEERS + 31) / 32];
+	__le32 seq;
+} __packed;
+
+#define HTT_TX_FETCH_RECORD_INFO_PEER_ID_MASK	0x0fff
+#define HTT_TX_FETCH_RECORD_INFO_PEER_ID_LSB	0
+#define HTT_TX_FETCH_RECORD_INFO_TID_MASK	0xf000
+#define HTT_TX_FETCH_RECORD_INFO_TID_LSB	12
+
+struct htt_tx_fetch_record {
+	__le16 info; /* HTT_TX_FETCH_IND_RECORD_INFO_ */
+	__le16 num_msdus;
+	__le32 num_bytes;
+} __packed;
+
+struct htt_tx_fetch_ind {
+	u8 pad0;
+	__le16 fetch_seq_num;
+	__le32 token;
+	__le16 num_resp_ids;
+	__le16 num_records;
+	struct htt_tx_fetch_record records[0];
+	__le32 resp_ids[0]; /* ath10k_htt_get_tx_fetch_ind_resp_ids() */
+} __packed;
+
+static inline void *
+ath10k_htt_get_tx_fetch_ind_resp_ids(struct htt_tx_fetch_ind *ind)
+{
+	return (void *)&ind->records[le16_to_cpu(ind->num_records)];
+}
+
+struct htt_tx_fetch_resp {
+	u8 pad0;
+	__le16 resp_id;
+	__le16 fetch_seq_num;
+	__le16 num_records;
+	__le32 token;
+	struct htt_tx_fetch_record records[0];
+} __packed;
+
+struct htt_tx_fetch_confirm {
+	u8 pad0;
+	__le16 num_resp_ids;
+	__le32 resp_ids[0];
+} __packed;
+
+enum htt_tx_mode_switch_mode {
+	HTT_TX_MODE_SWITCH_PUSH = 0,
+	HTT_TX_MODE_SWITCH_PUSH_PULL = 1,
+};
+
+#define HTT_TX_MODE_SWITCH_IND_INFO0_ENABLE		BIT(0)
+#define HTT_TX_MODE_SWITCH_IND_INFO0_NUM_RECORDS_MASK	0xfffe
+#define HTT_TX_MODE_SWITCH_IND_INFO0_NUM_RECORDS_LSB	1
+
+#define HTT_TX_MODE_SWITCH_IND_INFO1_MODE_MASK		0x0003
+#define HTT_TX_MODE_SWITCH_IND_INFO1_MODE_LSB		0
+#define HTT_TX_MODE_SWITCH_IND_INFO1_THRESHOLD_MASK	0xfffc
+#define HTT_TX_MODE_SWITCH_IND_INFO1_THRESHOLD_LSB	2
+
+#define HTT_TX_MODE_SWITCH_RECORD_INFO0_PEER_ID_MASK	0x0fff
+#define HTT_TX_MODE_SWITCH_RECORD_INFO0_PEER_ID_LSB	0
+#define HTT_TX_MODE_SWITCH_RECORD_INFO0_TID_MASK	0xf000
+#define HTT_TX_MODE_SWITCH_RECORD_INFO0_TID_LSB		12
+
+struct htt_tx_mode_switch_record {
+	__le16 info0; /* HTT_TX_MODE_SWITCH_RECORD_INFO0_ */
+	__le16 num_max_msdus;
+} __packed;
+
+struct htt_tx_mode_switch_ind {
+	u8 pad0;
+	__le16 info0; /* HTT_TX_MODE_SWITCH_IND_INFO0_ */
+	__le16 info1; /* HTT_TX_MODE_SWITCH_IND_INFO1_ */
+	u8 pad1[2];
+	struct htt_tx_mode_switch_record records[0];
 } __packed;
 
 union htt_rx_pn_t {
@@ -1340,6 +1483,7 @@ struct htt_cmd {
 		struct htt_oob_sync_req oob_sync_req;
 		struct htt_aggr_conf aggr_conf;
 		struct htt_frag_desc_bank_cfg frag_desc_bank_cfg;
+		struct htt_tx_fetch_resp tx_fetch_resp;
 	};
 } __packed;
 
@@ -1364,6 +1508,9 @@ struct htt_resp {
 		struct htt_rx_pn_ind rx_pn_ind;
 		struct htt_rx_offload_ind rx_offload_ind;
 		struct htt_rx_in_ord_ind rx_in_ord_ind;
+		struct htt_tx_fetch_ind tx_fetch_ind;
+		struct htt_tx_fetch_confirm tx_fetch_confirm;
+		struct htt_tx_mode_switch_ind tx_mode_switch_ind;
 	};
 } __packed;
 
-- 
2.1.4


_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k

[PATCH 2/5] ath10k: add new htt definitions

[Michal Kazior]

These definitions are associated with some
improvements upcomming for 10.4 and QCA99X0.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
---
 drivers/net/wireless/ath/ath10k/htt.h | 153 +++++++++++++++++++++++++++++++++-
 1 file changed, 150 insertions(+), 3 deletions(-)

diff --git a/drivers/net/wireless/ath/ath10k/htt.h b/drivers/net/wireless/ath/ath10k/htt.h
index edd3b9070de9..0c5628dafabf 100644
--- a/drivers/net/wireless/ath/ath10k/htt.h
+++ b/drivers/net/wireless/ath/ath10k/htt.h
@@ -52,6 +52,7 @@ enum htt_h2t_msg_type { /* host-to-target */
 	/* This command is used for sending management frames in HTT < 3.0.
 	 * HTT >= 3.0 uses TX_FRM for everything. */
 	HTT_H2T_MSG_TYPE_MGMT_TX            = 7,
+	HTT_H2T_MSG_TYPE_TX_FETCH_RESP      = 11,
 
 	HTT_H2T_NUM_MSGS /* keep this last */
 };
@@ -1306,9 +1307,43 @@ struct htt_frag_desc_bank_id {
  * so we use a conservatively safe value for now */
 #define HTT_FRAG_DESC_BANK_MAX 4
 
-#define HTT_FRAG_DESC_BANK_CFG_INFO_PDEV_ID_MASK 0x03
-#define HTT_FRAG_DESC_BANK_CFG_INFO_PDEV_ID_LSB  0
-#define HTT_FRAG_DESC_BANK_CFG_INFO_SWAP         (1 << 2)
+#define HTT_FRAG_DESC_BANK_CFG_INFO_PDEV_ID_MASK		0x03
+#define HTT_FRAG_DESC_BANK_CFG_INFO_PDEV_ID_LSB			0
+#define HTT_FRAG_DESC_BANK_CFG_INFO_SWAP			BIT(2)
+#define HTT_FRAG_DESC_BANK_CFG_INFO_Q_STATE_VALID		BIT(3)
+#define HTT_FRAG_DESC_BANK_CFG_INFO_Q_STATE_DEPTH_TYPE_MASK	BIT(4)
+#define HTT_FRAG_DESC_BANK_CFG_INFO_Q_STATE_DEPTH_TYPE_LSB	4
+
+enum htt_q_depth_type {
+	HTT_Q_DEPTH_TYPE_BYTES = 0,
+	HTT_Q_DEPTH_TYPE_MSDUS = 1,
+};
+
+#define HTT_TX_Q_STATE_NUM_PEERS		(TARGET_10_4_NUM_QCACHE_PEERS_MAX + \
+						 TARGET_10_4_NUM_VDEVS)
+#define HTT_TX_Q_STATE_NUM_TIDS			8
+#define HTT_TX_Q_STATE_ENTRY_SIZE		1
+#define HTT_TX_Q_STATE_ENTRY_MULTIPLIER		0
+
+/**
+ * htt_q_state_conf - part of htt_frag_desc_bank_cfg for host q state config
+ *
+ * Defines host q state format and behavior. See htt_q_state.
+ *
+ * @record_size: Defines the size of each host q entry in bytes. In practice
+ *	however firmware (at least 10.4.3-00191) ignores this host
+ *	configuration value and uses hardcoded value of 1.
+ * @record_multiplier: This is valid only when q depth type is MSDUs. It
+ *	defines the exponent for the power of 2 multiplication.
+ */
+struct htt_q_state_conf {
+	__le32 paddr;
+	__le16 num_peers;
+	__le16 num_tids;
+	u8 record_size;
+	u8 record_multiplier;
+	u8 pad[2];
+} __packed;
 
 struct htt_frag_desc_bank_cfg {
 	u8 info; /* HTT_FRAG_DESC_BANK_CFG_INFO_ */
@@ -1316,6 +1351,114 @@ struct htt_frag_desc_bank_cfg {
 	u8 desc_size;
 	__le32 bank_base_addrs[HTT_FRAG_DESC_BANK_MAX];
 	struct htt_frag_desc_bank_id bank_id[HTT_FRAG_DESC_BANK_MAX];
+	struct htt_q_state_conf q_state;
+} __packed;
+
+#define HTT_TX_Q_STATE_ENTRY_COEFFICIENT	128
+#define HTT_TX_Q_STATE_ENTRY_FACTOR_MASK	0x3f
+#define HTT_TX_Q_STATE_ENTRY_FACTOR_LSB		0
+#define HTT_TX_Q_STATE_ENTRY_EXP_MASK		0xc0
+#define HTT_TX_Q_STATE_ENTRY_EXP_LSB		6
+
+/**
+ * htt_q_state - shared between host and firmware via DMA
+ *
+ * This structure is used for the host to expose it's software queue state to
+ * firmware so that its rate control can schedule fetch requests for optimized
+ * performance. This is most notably used for MU-MIMO aggregation when multiple
+ * MU clients are connected.
+ *
+ * @count: Each element defines the host queue depth. When q depth type was
+ *	configured as HTT_Q_DEPTH_TYPE_BYTES then each entry is defined as:
+ *	FACTOR * 128 * 8^EXP (see HTT_TX_Q_STATE_ENTRY_FACTOR_MASK and
+ *	HTT_TX_Q_STATE_ENTRY_EXP_MASK). When q depth type was configured as
+ *	HTT_Q_DEPTH_TYPE_MSDUS the number of packets is scaled by 2 **
+ *	record_multiplier (see htt_q_state_conf).
+ * @map: Used by firmware to quickly check which host queues are not empty. It
+ *	is a bitmap simply saying.
+ * @seq: Used by firmware to quickly check if the host queues were updated
+ *	since it last checked.
+ *
+ * FIXME: Is the q_state map[] size calculation really correct?
+ */
+struct htt_q_state {
+	u8 count[HTT_TX_Q_STATE_NUM_TIDS][HTT_TX_Q_STATE_NUM_PEERS];
+	u32 map[HTT_TX_Q_STATE_NUM_TIDS][(HTT_TX_Q_STATE_NUM_PEERS + 31) / 32];
+	__le32 seq;
+} __packed;
+
+#define HTT_TX_FETCH_RECORD_INFO_PEER_ID_MASK	0x0fff
+#define HTT_TX_FETCH_RECORD_INFO_PEER_ID_LSB	0
+#define HTT_TX_FETCH_RECORD_INFO_TID_MASK	0xf000
+#define HTT_TX_FETCH_RECORD_INFO_TID_LSB	12
+
+struct htt_tx_fetch_record {
+	__le16 info; /* HTT_TX_FETCH_IND_RECORD_INFO_ */
+	__le16 num_msdus;
+	__le32 num_bytes;
+} __packed;
+
+struct htt_tx_fetch_ind {
+	u8 pad0;
+	__le16 fetch_seq_num;
+	__le32 token;
+	__le16 num_resp_ids;
+	__le16 num_records;
+	struct htt_tx_fetch_record records[0];
+	__le32 resp_ids[0]; /* ath10k_htt_get_tx_fetch_ind_resp_ids() */
+} __packed;
+
+static inline void *
+ath10k_htt_get_tx_fetch_ind_resp_ids(struct htt_tx_fetch_ind *ind)
+{
+	return (void *)&ind->records[le16_to_cpu(ind->num_records)];
+}
+
+struct htt_tx_fetch_resp {
+	u8 pad0;
+	__le16 resp_id;
+	__le16 fetch_seq_num;
+	__le16 num_records;
+	__le32 token;
+	struct htt_tx_fetch_record records[0];
+} __packed;
+
+struct htt_tx_fetch_confirm {
+	u8 pad0;
+	__le16 num_resp_ids;
+	__le32 resp_ids[0];
+} __packed;
+
+enum htt_tx_mode_switch_mode {
+	HTT_TX_MODE_SWITCH_PUSH = 0,
+	HTT_TX_MODE_SWITCH_PUSH_PULL = 1,
+};
+
+#define HTT_TX_MODE_SWITCH_IND_INFO0_ENABLE		BIT(0)
+#define HTT_TX_MODE_SWITCH_IND_INFO0_NUM_RECORDS_MASK	0xfffe
+#define HTT_TX_MODE_SWITCH_IND_INFO0_NUM_RECORDS_LSB	1
+
+#define HTT_TX_MODE_SWITCH_IND_INFO1_MODE_MASK		0x0003
+#define HTT_TX_MODE_SWITCH_IND_INFO1_MODE_LSB		0
+#define HTT_TX_MODE_SWITCH_IND_INFO1_THRESHOLD_MASK	0xfffc
+#define HTT_TX_MODE_SWITCH_IND_INFO1_THRESHOLD_LSB	2
+
+#define HTT_TX_MODE_SWITCH_RECORD_INFO0_PEER_ID_MASK	0x0fff
+#define HTT_TX_MODE_SWITCH_RECORD_INFO0_PEER_ID_LSB	0
+#define HTT_TX_MODE_SWITCH_RECORD_INFO0_TID_MASK	0xf000
+#define HTT_TX_MODE_SWITCH_RECORD_INFO0_TID_LSB		12
+
+struct htt_tx_mode_switch_record {
+	__le16 info0; /* HTT_TX_MODE_SWITCH_RECORD_INFO0_ */
+	__le16 num_max_msdus;
+} __packed;
+
+struct htt_tx_mode_switch_ind {
+	u8 pad0;
+	__le16 info0; /* HTT_TX_MODE_SWITCH_IND_INFO0_ */
+	__le16 info1; /* HTT_TX_MODE_SWITCH_IND_INFO1_ */
+	u8 pad1[2];
+	struct htt_tx_mode_switch_record records[0];
 } __packed;
 
 union htt_rx_pn_t {
@@ -1340,6 +1483,7 @@ struct htt_cmd {
 		struct htt_oob_sync_req oob_sync_req;
 		struct htt_aggr_conf aggr_conf;
 		struct htt_frag_desc_bank_cfg frag_desc_bank_cfg;
+		struct htt_tx_fetch_resp tx_fetch_resp;
 	};
 } __packed;
 
@@ -1364,6 +1508,9 @@ struct htt_resp {
 		struct htt_rx_pn_ind rx_pn_ind;
 		struct htt_rx_offload_ind rx_offload_ind;
 		struct htt_rx_in_ord_ind rx_in_ord_ind;
+		struct htt_tx_fetch_ind tx_fetch_ind;
+		struct htt_tx_fetch_confirm tx_fetch_confirm;
+		struct htt_tx_mode_switch_ind tx_mode_switch_ind;
 	};
 } __packed;
 
-- 
2.1.4

[PATCH 3/5] ath10k: add new FW_FEATURE_PEER_FLOW_CONTROL

[Michal Kazior]

This feature flag will be used for firmware which
supports pull-push model where host shares it's
software queue state with firmware and firmware
generates fetch requests telling host which queues
to dequeue tx from.

Primary function of this is improved MU-MIMO
performance with multiple clients.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
---
 drivers/net/wireless/ath/ath10k/core.c | 1 +
 drivers/net/wireless/ath/ath10k/core.h | 9 +++++++++
 2 files changed, 10 insertions(+)

diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c
index b41eb3f4ee56..48a26206c5c1 100644
--- a/drivers/net/wireless/ath/ath10k/core.c
+++ b/drivers/net/wireless/ath/ath10k/core.c
@@ -217,6 +217,7 @@ static const char *const ath10k_core_fw_feature_str[] = {
 	[ATH10K_FW_FEATURE_RAW_MODE_SUPPORT] = "raw-mode",
 	[ATH10K_FW_FEATURE_SUPPORTS_ADAPTIVE_CCA] = "adaptive-cca",
 	[ATH10K_FW_FEATURE_MFP_SUPPORT] = "mfp",
+	[ATH10K_FW_FEATURE_PEER_FLOW_CONTROL] = "peer-flow-ctrl",
 };
 
 static unsigned int ath10k_core_get_fw_feature_str(char *buf,
diff --git a/drivers/net/wireless/ath/ath10k/core.h b/drivers/net/wireless/ath/ath10k/core.h
index 7840cf3ef7a6..822e3195533a 100644
--- a/drivers/net/wireless/ath/ath10k/core.h
+++ b/drivers/net/wireless/ath/ath10k/core.h
@@ -510,6 +510,15 @@ enum ath10k_fw_features {
 	/* Firmware supports management frame protection */
 	ATH10K_FW_FEATURE_MFP_SUPPORT = 12,
 
+	/* Firmware supports pull-push model where host shares it's software
+	 * queue state with firmware and firmware generates fetch requests
+	 * telling host which queues to dequeue tx from.
+	 *
+	 * Primary function of this is improved MU-MIMO performance with
+	 * multiple clients.
+	 */
+	ATH10K_FW_FEATURE_PEER_FLOW_CONTROL = 13,
+
 	/* keep last */
 	ATH10K_FW_FEATURE_COUNT,
 };
-- 
2.1.4


_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k

[PATCH 3/5] ath10k: add new FW_FEATURE_PEER_FLOW_CONTROL

[Michal Kazior]

This feature flag will be used for firmware which
supports pull-push model where host shares it's
software queue state with firmware and firmware
generates fetch requests telling host which queues
to dequeue tx from.

Primary function of this is improved MU-MIMO
performance with multiple clients.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
---
 drivers/net/wireless/ath/ath10k/core.c | 1 +
 drivers/net/wireless/ath/ath10k/core.h | 9 +++++++++
 2 files changed, 10 insertions(+)

diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c
index b41eb3f4ee56..48a26206c5c1 100644
--- a/drivers/net/wireless/ath/ath10k/core.c
+++ b/drivers/net/wireless/ath/ath10k/core.c
@@ -217,6 +217,7 @@ static const char *const ath10k_core_fw_feature_str[] = {
 	[ATH10K_FW_FEATURE_RAW_MODE_SUPPORT] = "raw-mode",
 	[ATH10K_FW_FEATURE_SUPPORTS_ADAPTIVE_CCA] = "adaptive-cca",
 	[ATH10K_FW_FEATURE_MFP_SUPPORT] = "mfp",
+	[ATH10K_FW_FEATURE_PEER_FLOW_CONTROL] = "peer-flow-ctrl",
 };
 
 static unsigned int ath10k_core_get_fw_feature_str(char *buf,
diff --git a/drivers/net/wireless/ath/ath10k/core.h b/drivers/net/wireless/ath/ath10k/core.h
index 7840cf3ef7a6..822e3195533a 100644
--- a/drivers/net/wireless/ath/ath10k/core.h
+++ b/drivers/net/wireless/ath/ath10k/core.h
@@ -510,6 +510,15 @@ enum ath10k_fw_features {
 	/* Firmware supports management frame protection */
 	ATH10K_FW_FEATURE_MFP_SUPPORT = 12,
 
+	/* Firmware supports pull-push model where host shares it's software
+	 * queue state with firmware and firmware generates fetch requests
+	 * telling host which queues to dequeue tx from.
+	 *
+	 * Primary function of this is improved MU-MIMO performance with
+	 * multiple clients.
+	 */
+	ATH10K_FW_FEATURE_PEER_FLOW_CONTROL = 13,
+
 	/* keep last */
 	ATH10K_FW_FEATURE_COUNT,
 };
-- 
2.1.4

[PATCH 4/5] ath10k: clean up cont frag desc init code

[Michal Kazior]

This makes the code easier to extend and re-use.

While at it fix _warn to _err. Other than that
there are no functional changes.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
---
 drivers/net/wireless/ath/ath10k/htt_tx.c | 58 ++++++++++++++++++++++----------
 1 file changed, 41 insertions(+), 17 deletions(-)

diff --git a/drivers/net/wireless/ath/ath10k/htt_tx.c b/drivers/net/wireless/ath/ath10k/htt_tx.c
index b3adadb5f824..41a9811820e8 100644
--- a/drivers/net/wireless/ath/ath10k/htt_tx.c
+++ b/drivers/net/wireless/ath/ath10k/htt_tx.c
@@ -97,6 +97,41 @@ void ath10k_htt_tx_free_msdu_id(struct ath10k_htt *htt, u16 msdu_id)
 	idr_remove(&htt->pending_tx, msdu_id);
 }
 
+static void ath10k_htt_tx_free_cont_frag_desc(struct ath10k_htt *htt)
+{
+	size_t size;
+
+	if (!htt->frag_desc.vaddr)
+		return;
+
+	size = htt->max_num_pending_tx * sizeof(struct htt_msdu_ext_desc);
+
+	dma_free_coherent(htt->ar->dev,
+			  size,
+			  htt->frag_desc.vaddr,
+			  htt->frag_desc.paddr);
+}
+
+static int ath10k_htt_tx_alloc_cont_frag_desc(struct ath10k_htt *htt)
+{
+	struct ath10k *ar = htt->ar;
+	size_t size;
+
+	if (!ar->hw_params.continuous_frag_desc)
+		return 0;
+
+	size = htt->max_num_pending_tx * sizeof(struct htt_msdu_ext_desc);
+	htt->frag_desc.vaddr = dma_alloc_coherent(ar->dev, size,
+						  &htt->frag_desc.paddr,
+						  GFP_DMA);
+	if (!htt->frag_desc.vaddr) {
+		ath10k_err(ar, "failed to alloc fragment desc memory\n");
+		return -ENOMEM;
+	}
+
+	return 0;
+}
+
 int ath10k_htt_tx_alloc(struct ath10k_htt *htt)
 {
 	struct ath10k *ar = htt->ar;
@@ -118,20 +153,12 @@ int ath10k_htt_tx_alloc(struct ath10k_htt *htt)
 		goto free_idr_pending_tx;
 	}
 
-	if (!ar->hw_params.continuous_frag_desc)
-		goto skip_frag_desc_alloc;
-
-	size = htt->max_num_pending_tx * sizeof(struct htt_msdu_ext_desc);
-	htt->frag_desc.vaddr = dma_alloc_coherent(ar->dev, size,
-						  &htt->frag_desc.paddr,
-						  GFP_KERNEL);
-	if (!htt->frag_desc.vaddr) {
-		ath10k_warn(ar, "failed to alloc fragment desc memory\n");
-		ret = -ENOMEM;
+	ret = ath10k_htt_tx_alloc_cont_frag_desc(htt);
+	if (ret) {
+		ath10k_err(ar, "failed to alloc cont frag desc: %d\n", ret);
 		goto free_txbuf;
 	}
 
-skip_frag_desc_alloc:
 	return 0;
 
 free_txbuf:
@@ -139,8 +166,10 @@ free_txbuf:
 			  sizeof(struct ath10k_htt_txbuf);
 	dma_free_coherent(htt->ar->dev, size, htt->txbuf.vaddr,
 			  htt->txbuf.paddr);
+
 free_idr_pending_tx:
 	idr_destroy(&htt->pending_tx);
+
 	return ret;
 }
 
@@ -174,12 +203,7 @@ void ath10k_htt_tx_free(struct ath10k_htt *htt)
 				  htt->txbuf.paddr);
 	}
 
-	if (htt->frag_desc.vaddr) {
-		size = htt->max_num_pending_tx *
-				  sizeof(struct htt_msdu_ext_desc);
-		dma_free_coherent(htt->ar->dev, size, htt->frag_desc.vaddr,
-				  htt->frag_desc.paddr);
-	}
+	ath10k_htt_tx_free_cont_frag_desc(htt);
 }
 
 void ath10k_htt_htc_tx_complete(struct ath10k *ar, struct sk_buff *skb)
-- 
2.1.4


_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k

[PATCH 4/5] ath10k: clean up cont frag desc init code

[Michal Kazior]

This makes the code easier to extend and re-use.

While at it fix _warn to _err. Other than that
there are no functional changes.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
---
 drivers/net/wireless/ath/ath10k/htt_tx.c | 58 ++++++++++++++++++++++----------
 1 file changed, 41 insertions(+), 17 deletions(-)

diff --git a/drivers/net/wireless/ath/ath10k/htt_tx.c b/drivers/net/wireless/ath/ath10k/htt_tx.c
index b3adadb5f824..41a9811820e8 100644
--- a/drivers/net/wireless/ath/ath10k/htt_tx.c
+++ b/drivers/net/wireless/ath/ath10k/htt_tx.c
@@ -97,6 +97,41 @@ void ath10k_htt_tx_free_msdu_id(struct ath10k_htt *htt, u16 msdu_id)
 	idr_remove(&htt->pending_tx, msdu_id);
 }
 
+static void ath10k_htt_tx_free_cont_frag_desc(struct ath10k_htt *htt)
+{
+	size_t size;
+
+	if (!htt->frag_desc.vaddr)
+		return;
+
+	size = htt->max_num_pending_tx * sizeof(struct htt_msdu_ext_desc);
+
+	dma_free_coherent(htt->ar->dev,
+			  size,
+			  htt->frag_desc.vaddr,
+			  htt->frag_desc.paddr);
+}
+
+static int ath10k_htt_tx_alloc_cont_frag_desc(struct ath10k_htt *htt)
+{
+	struct ath10k *ar = htt->ar;
+	size_t size;
+
+	if (!ar->hw_params.continuous_frag_desc)
+		return 0;
+
+	size = htt->max_num_pending_tx * sizeof(struct htt_msdu_ext_desc);
+	htt->frag_desc.vaddr = dma_alloc_coherent(ar->dev, size,
+						  &htt->frag_desc.paddr,
+						  GFP_DMA);
+	if (!htt->frag_desc.vaddr) {
+		ath10k_err(ar, "failed to alloc fragment desc memory\n");
+		return -ENOMEM;
+	}
+
+	return 0;
+}
+
 int ath10k_htt_tx_alloc(struct ath10k_htt *htt)
 {
 	struct ath10k *ar = htt->ar;
@@ -118,20 +153,12 @@ int ath10k_htt_tx_alloc(struct ath10k_htt *htt)
 		goto free_idr_pending_tx;
 	}
 
-	if (!ar->hw_params.continuous_frag_desc)
-		goto skip_frag_desc_alloc;
-
-	size = htt->max_num_pending_tx * sizeof(struct htt_msdu_ext_desc);
-	htt->frag_desc.vaddr = dma_alloc_coherent(ar->dev, size,
-						  &htt->frag_desc.paddr,
-						  GFP_KERNEL);
-	if (!htt->frag_desc.vaddr) {
-		ath10k_warn(ar, "failed to alloc fragment desc memory\n");
-		ret = -ENOMEM;
+	ret = ath10k_htt_tx_alloc_cont_frag_desc(htt);
+	if (ret) {
+		ath10k_err(ar, "failed to alloc cont frag desc: %d\n", ret);
 		goto free_txbuf;
 	}
 
-skip_frag_desc_alloc:
 	return 0;
 
 free_txbuf:
@@ -139,8 +166,10 @@ free_txbuf:
 			  sizeof(struct ath10k_htt_txbuf);
 	dma_free_coherent(htt->ar->dev, size, htt->txbuf.vaddr,
 			  htt->txbuf.paddr);
+
 free_idr_pending_tx:
 	idr_destroy(&htt->pending_tx);
+
 	return ret;
 }
 
@@ -174,12 +203,7 @@ void ath10k_htt_tx_free(struct ath10k_htt *htt)
 				  htt->txbuf.paddr);
 	}
 
-	if (htt->frag_desc.vaddr) {
-		size = htt->max_num_pending_tx *
-				  sizeof(struct htt_msdu_ext_desc);
-		dma_free_coherent(htt->ar->dev, size, htt->frag_desc.vaddr,
-				  htt->frag_desc.paddr);
-	}
+	ath10k_htt_tx_free_cont_frag_desc(htt);
 }
 
 void ath10k_htt_htc_tx_complete(struct ath10k *ar, struct sk_buff *skb)
-- 
2.1.4

Re: [PATCH 4/5] ath10k: clean up cont frag desc init code

[Ben Greear]

On 01/13/2016 06:01 AM, Michal Kazior wrote:
> This makes the code easier to extend and re-use.
>
> While at it fix _warn to _err. Other than that
> there are no functional changes.
>
> Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
> ---
>   drivers/net/wireless/ath/ath10k/htt_tx.c | 58 ++++++++++++++++++++++----------
>   1 file changed, 41 insertions(+), 17 deletions(-)
>
> diff --git a/drivers/net/wireless/ath/ath10k/htt_tx.c b/drivers/net/wireless/ath/ath10k/htt_tx.c
> index b3adadb5f824..41a9811820e8 100644
> --- a/drivers/net/wireless/ath/ath10k/htt_tx.c
> +++ b/drivers/net/wireless/ath/ath10k/htt_tx.c
> @@ -97,6 +97,41 @@ void ath10k_htt_tx_free_msdu_id(struct ath10k_htt *htt, u16 msdu_id)
>   	idr_remove(&htt->pending_tx, msdu_id);
>   }
>
> +static void ath10k_htt_tx_free_cont_frag_desc(struct ath10k_htt *htt)
> +{
> +	size_t size;
> +
> +	if (!htt->frag_desc.vaddr)
> +		return;
> +
> +	size = htt->max_num_pending_tx * sizeof(struct htt_msdu_ext_desc);
> +
> +	dma_free_coherent(htt->ar->dev,
> +			  size,
> +			  htt->frag_desc.vaddr,
> +			  htt->frag_desc.paddr);
> +}
> +
> +static int ath10k_htt_tx_alloc_cont_frag_desc(struct ath10k_htt *htt)
> +{
> +	struct ath10k *ar = htt->ar;
> +	size_t size;
> +
> +	if (!ar->hw_params.continuous_frag_desc)
> +		return 0;
> +
> +	size = htt->max_num_pending_tx * sizeof(struct htt_msdu_ext_desc);
> +	htt->frag_desc.vaddr = dma_alloc_coherent(ar->dev, size,
> +						  &htt->frag_desc.paddr,
> +						  GFP_DMA);

Did you mean to change GFP_KERNEL to GFP_DMA?

> -	size = htt->max_num_pending_tx * sizeof(struct htt_msdu_ext_desc);
> -	htt->frag_desc.vaddr = dma_alloc_coherent(ar->dev, size,
> -						  &htt->frag_desc.paddr,
> -						  GFP_KERNEL);
> -	if (!htt->frag_desc.vaddr) {
> -		ath10k_warn(ar, "failed to alloc fragment desc memory\n");
> -		ret = -ENOMEM;
> +	ret = ath10k_htt_tx_alloc_cont_frag_desc(htt);
> +	if (ret) {
> +		ath10k_err(ar, "failed to alloc cont frag desc: %d\n", ret);
>   		goto free_txbuf;
>   	}


Thanks,
Ben


-- 
Ben Greear <greearb@candelatech.com>
Candela Technologies Inc  http://www.candelatech.com


_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k

Re: [PATCH 4/5] ath10k: clean up cont frag desc init code

[Ben Greear]

On 01/13/2016 06:01 AM, Michal Kazior wrote:
> This makes the code easier to extend and re-use.
>
> While at it fix _warn to _err. Other than that
> there are no functional changes.
>
> Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
> ---
>   drivers/net/wireless/ath/ath10k/htt_tx.c | 58 ++++++++++++++++++++++----------
>   1 file changed, 41 insertions(+), 17 deletions(-)
>
> diff --git a/drivers/net/wireless/ath/ath10k/htt_tx.c b/drivers/net/wireless/ath/ath10k/htt_tx.c
> index b3adadb5f824..41a9811820e8 100644
> --- a/drivers/net/wireless/ath/ath10k/htt_tx.c
> +++ b/drivers/net/wireless/ath/ath10k/htt_tx.c
> @@ -97,6 +97,41 @@ void ath10k_htt_tx_free_msdu_id(struct ath10k_htt *htt, u16 msdu_id)
>   	idr_remove(&htt->pending_tx, msdu_id);
>   }
>
> +static void ath10k_htt_tx_free_cont_frag_desc(struct ath10k_htt *htt)
> +{
> +	size_t size;
> +
> +	if (!htt->frag_desc.vaddr)
> +		return;
> +
> +	size = htt->max_num_pending_tx * sizeof(struct htt_msdu_ext_desc);
> +
> +	dma_free_coherent(htt->ar->dev,
> +			  size,
> +			  htt->frag_desc.vaddr,
> +			  htt->frag_desc.paddr);
> +}
> +
> +static int ath10k_htt_tx_alloc_cont_frag_desc(struct ath10k_htt *htt)
> +{
> +	struct ath10k *ar = htt->ar;
> +	size_t size;
> +
> +	if (!ar->hw_params.continuous_frag_desc)
> +		return 0;
> +
> +	size = htt->max_num_pending_tx * sizeof(struct htt_msdu_ext_desc);
> +	htt->frag_desc.vaddr = dma_alloc_coherent(ar->dev, size,
> +						  &htt->frag_desc.paddr,
> +						  GFP_DMA);

Did you mean to change GFP_KERNEL to GFP_DMA?

> -	size = htt->max_num_pending_tx * sizeof(struct htt_msdu_ext_desc);
> -	htt->frag_desc.vaddr = dma_alloc_coherent(ar->dev, size,
> -						  &htt->frag_desc.paddr,
> -						  GFP_KERNEL);
> -	if (!htt->frag_desc.vaddr) {
> -		ath10k_warn(ar, "failed to alloc fragment desc memory\n");
> -		ret = -ENOMEM;
> +	ret = ath10k_htt_tx_alloc_cont_frag_desc(htt);
> +	if (ret) {
> +		ath10k_err(ar, "failed to alloc cont frag desc: %d\n", ret);
>   		goto free_txbuf;
>   	}


Thanks,
Ben


-- 
Ben Greear <greearb@candelatech.com>
Candela Technologies Inc  http://www.candelatech.com

Re: [PATCH 4/5] ath10k: clean up cont frag desc init code

[Michal Kazior]

On 20 January 2016 at 20:34, Ben Greear <greearb@candelatech.com> wrote:
> On 01/13/2016 06:01 AM, Michal Kazior wrote:
>>
>> This makes the code easier to extend and re-use.
>>
>> While at it fix _warn to _err. Other than that
>> there are no functional changes.
>>
>> Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
>> ---
>>   drivers/net/wireless/ath/ath10k/htt_tx.c | 58
>> ++++++++++++++++++++++----------
>>   1 file changed, 41 insertions(+), 17 deletions(-)
>>
>> diff --git a/drivers/net/wireless/ath/ath10k/htt_tx.c
>> b/drivers/net/wireless/ath/ath10k/htt_tx.c
>> index b3adadb5f824..41a9811820e8 100644
>> --- a/drivers/net/wireless/ath/ath10k/htt_tx.c
>> +++ b/drivers/net/wireless/ath/ath10k/htt_tx.c
>> @@ -97,6 +97,41 @@ void ath10k_htt_tx_free_msdu_id(struct ath10k_htt *htt,
>> u16 msdu_id)
>>         idr_remove(&htt->pending_tx, msdu_id);
>>   }
>>
>> +static void ath10k_htt_tx_free_cont_frag_desc(struct ath10k_htt *htt)
>> +{
>> +       size_t size;
>> +
>> +       if (!htt->frag_desc.vaddr)
>> +               return;
>> +
>> +       size = htt->max_num_pending_tx * sizeof(struct htt_msdu_ext_desc);
>> +
>> +       dma_free_coherent(htt->ar->dev,
>> +                         size,
>> +                         htt->frag_desc.vaddr,
>> +                         htt->frag_desc.paddr);
>> +}
>> +
>> +static int ath10k_htt_tx_alloc_cont_frag_desc(struct ath10k_htt *htt)
>> +{
>> +       struct ath10k *ar = htt->ar;
>> +       size_t size;
>> +
>> +       if (!ar->hw_params.continuous_frag_desc)
>> +               return 0;
>> +
>> +       size = htt->max_num_pending_tx * sizeof(struct htt_msdu_ext_desc);
>> +       htt->frag_desc.vaddr = dma_alloc_coherent(ar->dev, size,
>> +                                                 &htt->frag_desc.paddr,
>> +                                                 GFP_DMA);
>
>
> Did you mean to change GFP_KERNEL to GFP_DMA?

Ah, good catch! I obviously meant to keep GFP_KERNEL. I must've missed
that during a rebase at some point.


Michał

_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k

Re: [PATCH 4/5] ath10k: clean up cont frag desc init code

[Michal Kazior]

On 20 January 2016 at 20:34, Ben Greear <greearb@candelatech.com> wrote:
> On 01/13/2016 06:01 AM, Michal Kazior wrote:
>>
>> This makes the code easier to extend and re-use.
>>
>> While at it fix _warn to _err. Other than that
>> there are no functional changes.
>>
>> Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
>> ---
>>   drivers/net/wireless/ath/ath10k/htt_tx.c | 58
>> ++++++++++++++++++++++----------
>>   1 file changed, 41 insertions(+), 17 deletions(-)
>>
>> diff --git a/drivers/net/wireless/ath/ath10k/htt_tx.c
>> b/drivers/net/wireless/ath/ath10k/htt_tx.c
>> index b3adadb5f824..41a9811820e8 100644
>> --- a/drivers/net/wireless/ath/ath10k/htt_tx.c
>> +++ b/drivers/net/wireless/ath/ath10k/htt_tx.c
>> @@ -97,6 +97,41 @@ void ath10k_htt_tx_free_msdu_id(struct ath10k_htt *htt,
>> u16 msdu_id)
>>         idr_remove(&htt->pending_tx, msdu_id);
>>   }
>>
>> +static void ath10k_htt_tx_free_cont_frag_desc(struct ath10k_htt *htt)
>> +{
>> +       size_t size;
>> +
>> +       if (!htt->frag_desc.vaddr)
>> +               return;
>> +
>> +       size = htt->max_num_pending_tx * sizeof(struct htt_msdu_ext_desc);
>> +
>> +       dma_free_coherent(htt->ar->dev,
>> +                         size,
>> +                         htt->frag_desc.vaddr,
>> +                         htt->frag_desc.paddr);
>> +}
>> +
>> +static int ath10k_htt_tx_alloc_cont_frag_desc(struct ath10k_htt *htt)
>> +{
>> +       struct ath10k *ar = htt->ar;
>> +       size_t size;
>> +
>> +       if (!ar->hw_params.continuous_frag_desc)
>> +               return 0;
>> +
>> +       size = htt->max_num_pending_tx * sizeof(struct htt_msdu_ext_desc);
>> +       htt->frag_desc.vaddr = dma_alloc_coherent(ar->dev, size,
>> +                                                 &htt->frag_desc.paddr,
>> +                                                 GFP_DMA);
>
>
> Did you mean to change GFP_KERNEL to GFP_DMA?

Ah, good catch! I obviously meant to keep GFP_KERNEL. I must've missed
that during a rebase at some point.


Michał

[PATCH 5/5] ath10k: implement basic support for new tx path firmware

[Michal Kazior]

This allows to use the new firmware which
implements the new tx data path. Without this
patch firmware supporting new tx path stops
responding shortly after booting.

This patch doesn't implement the entire pull-push
logic available in the new firmware. This will be
done in subsequent patches.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
---
 drivers/net/wireless/ath/ath10k/htt.h    |  8 +++
 drivers/net/wireless/ath/ath10k/htt_rx.c |  4 +-
 drivers/net/wireless/ath/ath10k/htt_tx.c | 88 +++++++++++++++++++++++++++++---
 3 files changed, 91 insertions(+), 9 deletions(-)

diff --git a/drivers/net/wireless/ath/ath10k/htt.h b/drivers/net/wireless/ath/ath10k/htt.h
index 0c5628dafabf..13391ea4422d 100644
--- a/drivers/net/wireless/ath/ath10k/htt.h
+++ b/drivers/net/wireless/ath/ath10k/htt.h
@@ -1665,6 +1665,14 @@ struct ath10k_htt {
 		dma_addr_t paddr;
 		struct ath10k_htt_txbuf *vaddr;
 	} txbuf;
+
+	struct {
+		struct htt_q_state *vaddr;
+		dma_addr_t paddr;
+		u16 num_peers;
+		u16 num_tids;
+		enum htt_q_depth_type type;
+	} tx_q_state;
 };
 
 #define RX_HTT_HDR_STATUS_LEN 64
diff --git a/drivers/net/wireless/ath/ath10k/htt_rx.c b/drivers/net/wireless/ath/ath10k/htt_rx.c
index d923f64e4f42..248405b53ef4 100644
--- a/drivers/net/wireless/ath/ath10k/htt_rx.c
+++ b/drivers/net/wireless/ath/ath10k/htt_rx.c
@@ -2123,10 +2123,12 @@ void ath10k_htt_t2h_msg_handler(struct ath10k *ar, struct sk_buff *skb)
 		break;
 	case HTT_T2H_MSG_TYPE_AGGR_CONF:
 		break;
-	case HTT_T2H_MSG_TYPE_EN_STATS:
 	case HTT_T2H_MSG_TYPE_TX_FETCH_IND:
 	case HTT_T2H_MSG_TYPE_TX_FETCH_CONFIRM:
 	case HTT_T2H_MSG_TYPE_TX_MODE_SWITCH_IND:
+		/* TODO: Implement pull-push logic */
+		break;
+	case HTT_T2H_MSG_TYPE_EN_STATS:
 	default:
 		ath10k_warn(ar, "htt event (%d) not handled\n",
 			    resp->hdr.msg_type);
diff --git a/drivers/net/wireless/ath/ath10k/htt_tx.c b/drivers/net/wireless/ath/ath10k/htt_tx.c
index 41a9811820e8..3cc2261b459e 100644
--- a/drivers/net/wireless/ath/ath10k/htt_tx.c
+++ b/drivers/net/wireless/ath/ath10k/htt_tx.c
@@ -132,6 +132,50 @@ static int ath10k_htt_tx_alloc_cont_frag_desc(struct ath10k_htt *htt)
 	return 0;
 }
 
+static void ath10k_htt_tx_free_txq(struct ath10k_htt *htt)
+{
+	struct ath10k *ar = htt->ar;
+	size_t size;
+
+	if (!test_bit(ATH10K_FW_FEATURE_PEER_FLOW_CONTROL, ar->fw_features))
+		return;
+
+	size = sizeof(*htt->tx_q_state.vaddr);
+
+	dma_unmap_single(ar->dev, htt->tx_q_state.paddr, size, DMA_TO_DEVICE);
+	kfree(htt->tx_q_state.vaddr);
+}
+
+static int ath10k_htt_tx_alloc_txq(struct ath10k_htt *htt)
+{
+	struct ath10k *ar = htt->ar;
+	size_t size;
+	int ret;
+
+	if (!test_bit(ATH10K_FW_FEATURE_PEER_FLOW_CONTROL, ar->fw_features))
+		return 0;
+
+	htt->tx_q_state.num_peers = HTT_TX_Q_STATE_NUM_PEERS;
+	htt->tx_q_state.num_tids = HTT_TX_Q_STATE_NUM_TIDS;
+	htt->tx_q_state.type = HTT_Q_DEPTH_TYPE_BYTES;
+
+	size = sizeof(*htt->tx_q_state.vaddr);
+	htt->tx_q_state.vaddr = kzalloc(size, GFP_KERNEL);
+	if (!htt->tx_q_state.vaddr)
+		return -ENOMEM;
+
+	htt->tx_q_state.paddr = dma_map_single(ar->dev, htt->tx_q_state.vaddr,
+					       size, DMA_TO_DEVICE);
+	ret = dma_mapping_error(ar->dev, htt->tx_q_state.paddr);
+	if (ret) {
+		ath10k_warn(ar, "failed to dma map tx_q_state: %d\n", ret);
+		kfree(htt->tx_q_state.vaddr);
+		return -EIO;
+	}
+
+	return 0;
+}
+
 int ath10k_htt_tx_alloc(struct ath10k_htt *htt)
 {
 	struct ath10k *ar = htt->ar;
@@ -159,8 +203,17 @@ int ath10k_htt_tx_alloc(struct ath10k_htt *htt)
 		goto free_txbuf;
 	}
 
+	ret = ath10k_htt_tx_alloc_txq(htt);
+	if (ret) {
+		ath10k_err(ar, "failed to alloc txq: %d\n", ret);
+		goto free_frag_desc;
+	}
+
 	return 0;
 
+free_frag_desc:
+	ath10k_htt_tx_free_cont_frag_desc(htt);
+
 free_txbuf:
 	size = htt->max_num_pending_tx *
 			  sizeof(struct ath10k_htt_txbuf);
@@ -203,6 +256,7 @@ void ath10k_htt_tx_free(struct ath10k_htt *htt)
 				  htt->txbuf.paddr);
 	}
 
+	ath10k_htt_tx_free_txq(htt);
 	ath10k_htt_tx_free_cont_frag_desc(htt);
 }
 
@@ -292,7 +346,9 @@ int ath10k_htt_send_frag_desc_bank_cfg(struct ath10k_htt *htt)
 	struct ath10k *ar = htt->ar;
 	struct sk_buff *skb;
 	struct htt_cmd *cmd;
+	struct htt_frag_desc_bank_cfg *cfg;
 	int ret, size;
+	u8 info;
 
 	if (!ar->hw_params.continuous_frag_desc)
 		return 0;
@@ -310,14 +366,30 @@ int ath10k_htt_send_frag_desc_bank_cfg(struct ath10k_htt *htt)
 	skb_put(skb, size);
 	cmd = (struct htt_cmd *)skb->data;
 	cmd->hdr.msg_type = HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG;
-	cmd->frag_desc_bank_cfg.info = 0;
-	cmd->frag_desc_bank_cfg.num_banks = 1;
-	cmd->frag_desc_bank_cfg.desc_size = sizeof(struct htt_msdu_ext_desc);
-	cmd->frag_desc_bank_cfg.bank_base_addrs[0] =
-				__cpu_to_le32(htt->frag_desc.paddr);
-	cmd->frag_desc_bank_cfg.bank_id[0].bank_min_id = 0;
-	cmd->frag_desc_bank_cfg.bank_id[0].bank_max_id =
-				__cpu_to_le16(htt->max_num_pending_tx - 1);
+
+	info = 0;
+	info |= SM(htt->tx_q_state.type,
+		   HTT_FRAG_DESC_BANK_CFG_INFO_Q_STATE_DEPTH_TYPE);
+
+	if (test_bit(ATH10K_FW_FEATURE_PEER_FLOW_CONTROL, ar->fw_features))
+		info |= HTT_FRAG_DESC_BANK_CFG_INFO_Q_STATE_VALID;
+
+	cfg = &cmd->frag_desc_bank_cfg;
+	cfg->info = info;
+	cfg->num_banks = 1;
+	cfg->desc_size = sizeof(struct htt_msdu_ext_desc);
+	cfg->bank_base_addrs[0] = __cpu_to_le32(htt->frag_desc.paddr);
+	cfg->bank_id[0].bank_min_id = 0;
+	cfg->bank_id[0].bank_max_id = __cpu_to_le16(htt->max_num_pending_tx -
+						    1);
+
+	cfg->q_state.paddr = cpu_to_le32(htt->tx_q_state.paddr);
+	cfg->q_state.num_peers = cpu_to_le16(htt->tx_q_state.num_peers);
+	cfg->q_state.num_tids = cpu_to_le16(htt->tx_q_state.num_tids);
+	cfg->q_state.record_size = HTT_TX_Q_STATE_ENTRY_SIZE;
+	cfg->q_state.record_multiplier = HTT_TX_Q_STATE_ENTRY_MULTIPLIER;
+
+	ath10k_dbg(ar, ATH10K_DBG_HTT, "htt frag desc bank cmd\n");
 
 	ret = ath10k_htc_send(&htt->ar->htc, htt->eid, skb);
 	if (ret) {
-- 
2.1.4


_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k

[PATCH 5/5] ath10k: implement basic support for new tx path firmware

[Michal Kazior]

This allows to use the new firmware which
implements the new tx data path. Without this
patch firmware supporting new tx path stops
responding shortly after booting.

This patch doesn't implement the entire pull-push
logic available in the new firmware. This will be
done in subsequent patches.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
---
 drivers/net/wireless/ath/ath10k/htt.h    |  8 +++
 drivers/net/wireless/ath/ath10k/htt_rx.c |  4 +-
 drivers/net/wireless/ath/ath10k/htt_tx.c | 88 +++++++++++++++++++++++++++++---
 3 files changed, 91 insertions(+), 9 deletions(-)

diff --git a/drivers/net/wireless/ath/ath10k/htt.h b/drivers/net/wireless/ath/ath10k/htt.h
index 0c5628dafabf..13391ea4422d 100644
--- a/drivers/net/wireless/ath/ath10k/htt.h
+++ b/drivers/net/wireless/ath/ath10k/htt.h
@@ -1665,6 +1665,14 @@ struct ath10k_htt {
 		dma_addr_t paddr;
 		struct ath10k_htt_txbuf *vaddr;
 	} txbuf;
+
+	struct {
+		struct htt_q_state *vaddr;
+		dma_addr_t paddr;
+		u16 num_peers;
+		u16 num_tids;
+		enum htt_q_depth_type type;
+	} tx_q_state;
 };
 
 #define RX_HTT_HDR_STATUS_LEN 64
diff --git a/drivers/net/wireless/ath/ath10k/htt_rx.c b/drivers/net/wireless/ath/ath10k/htt_rx.c
index d923f64e4f42..248405b53ef4 100644
--- a/drivers/net/wireless/ath/ath10k/htt_rx.c
+++ b/drivers/net/wireless/ath/ath10k/htt_rx.c
@@ -2123,10 +2123,12 @@ void ath10k_htt_t2h_msg_handler(struct ath10k *ar, struct sk_buff *skb)
 		break;
 	case HTT_T2H_MSG_TYPE_AGGR_CONF:
 		break;
-	case HTT_T2H_MSG_TYPE_EN_STATS:
 	case HTT_T2H_MSG_TYPE_TX_FETCH_IND:
 	case HTT_T2H_MSG_TYPE_TX_FETCH_CONFIRM:
 	case HTT_T2H_MSG_TYPE_TX_MODE_SWITCH_IND:
+		/* TODO: Implement pull-push logic */
+		break;
+	case HTT_T2H_MSG_TYPE_EN_STATS:
 	default:
 		ath10k_warn(ar, "htt event (%d) not handled\n",
 			    resp->hdr.msg_type);
diff --git a/drivers/net/wireless/ath/ath10k/htt_tx.c b/drivers/net/wireless/ath/ath10k/htt_tx.c
index 41a9811820e8..3cc2261b459e 100644
--- a/drivers/net/wireless/ath/ath10k/htt_tx.c
+++ b/drivers/net/wireless/ath/ath10k/htt_tx.c
@@ -132,6 +132,50 @@ static int ath10k_htt_tx_alloc_cont_frag_desc(struct ath10k_htt *htt)
 	return 0;
 }
 
+static void ath10k_htt_tx_free_txq(struct ath10k_htt *htt)
+{
+	struct ath10k *ar = htt->ar;
+	size_t size;
+
+	if (!test_bit(ATH10K_FW_FEATURE_PEER_FLOW_CONTROL, ar->fw_features))
+		return;
+
+	size = sizeof(*htt->tx_q_state.vaddr);
+
+	dma_unmap_single(ar->dev, htt->tx_q_state.paddr, size, DMA_TO_DEVICE);
+	kfree(htt->tx_q_state.vaddr);
+}
+
+static int ath10k_htt_tx_alloc_txq(struct ath10k_htt *htt)
+{
+	struct ath10k *ar = htt->ar;
+	size_t size;
+	int ret;
+
+	if (!test_bit(ATH10K_FW_FEATURE_PEER_FLOW_CONTROL, ar->fw_features))
+		return 0;
+
+	htt->tx_q_state.num_peers = HTT_TX_Q_STATE_NUM_PEERS;
+	htt->tx_q_state.num_tids = HTT_TX_Q_STATE_NUM_TIDS;
+	htt->tx_q_state.type = HTT_Q_DEPTH_TYPE_BYTES;
+
+	size = sizeof(*htt->tx_q_state.vaddr);
+	htt->tx_q_state.vaddr = kzalloc(size, GFP_KERNEL);
+	if (!htt->tx_q_state.vaddr)
+		return -ENOMEM;
+
+	htt->tx_q_state.paddr = dma_map_single(ar->dev, htt->tx_q_state.vaddr,
+					       size, DMA_TO_DEVICE);
+	ret = dma_mapping_error(ar->dev, htt->tx_q_state.paddr);
+	if (ret) {
+		ath10k_warn(ar, "failed to dma map tx_q_state: %d\n", ret);
+		kfree(htt->tx_q_state.vaddr);
+		return -EIO;
+	}
+
+	return 0;
+}
+
 int ath10k_htt_tx_alloc(struct ath10k_htt *htt)
 {
 	struct ath10k *ar = htt->ar;
@@ -159,8 +203,17 @@ int ath10k_htt_tx_alloc(struct ath10k_htt *htt)
 		goto free_txbuf;
 	}
 
+	ret = ath10k_htt_tx_alloc_txq(htt);
+	if (ret) {
+		ath10k_err(ar, "failed to alloc txq: %d\n", ret);
+		goto free_frag_desc;
+	}
+
 	return 0;
 
+free_frag_desc:
+	ath10k_htt_tx_free_cont_frag_desc(htt);
+
 free_txbuf:
 	size = htt->max_num_pending_tx *
 			  sizeof(struct ath10k_htt_txbuf);
@@ -203,6 +256,7 @@ void ath10k_htt_tx_free(struct ath10k_htt *htt)
 				  htt->txbuf.paddr);
 	}
 
+	ath10k_htt_tx_free_txq(htt);
 	ath10k_htt_tx_free_cont_frag_desc(htt);
 }
 
@@ -292,7 +346,9 @@ int ath10k_htt_send_frag_desc_bank_cfg(struct ath10k_htt *htt)
 	struct ath10k *ar = htt->ar;
 	struct sk_buff *skb;
 	struct htt_cmd *cmd;
+	struct htt_frag_desc_bank_cfg *cfg;
 	int ret, size;
+	u8 info;
 
 	if (!ar->hw_params.continuous_frag_desc)
 		return 0;
@@ -310,14 +366,30 @@ int ath10k_htt_send_frag_desc_bank_cfg(struct ath10k_htt *htt)
 	skb_put(skb, size);
 	cmd = (struct htt_cmd *)skb->data;
 	cmd->hdr.msg_type = HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG;
-	cmd->frag_desc_bank_cfg.info = 0;
-	cmd->frag_desc_bank_cfg.num_banks = 1;
-	cmd->frag_desc_bank_cfg.desc_size = sizeof(struct htt_msdu_ext_desc);
-	cmd->frag_desc_bank_cfg.bank_base_addrs[0] =
-				__cpu_to_le32(htt->frag_desc.paddr);
-	cmd->frag_desc_bank_cfg.bank_id[0].bank_min_id = 0;
-	cmd->frag_desc_bank_cfg.bank_id[0].bank_max_id =
-				__cpu_to_le16(htt->max_num_pending_tx - 1);
+
+	info = 0;
+	info |= SM(htt->tx_q_state.type,
+		   HTT_FRAG_DESC_BANK_CFG_INFO_Q_STATE_DEPTH_TYPE);
+
+	if (test_bit(ATH10K_FW_FEATURE_PEER_FLOW_CONTROL, ar->fw_features))
+		info |= HTT_FRAG_DESC_BANK_CFG_INFO_Q_STATE_VALID;
+
+	cfg = &cmd->frag_desc_bank_cfg;
+	cfg->info = info;
+	cfg->num_banks = 1;
+	cfg->desc_size = sizeof(struct htt_msdu_ext_desc);
+	cfg->bank_base_addrs[0] = __cpu_to_le32(htt->frag_desc.paddr);
+	cfg->bank_id[0].bank_min_id = 0;
+	cfg->bank_id[0].bank_max_id = __cpu_to_le16(htt->max_num_pending_tx -
+						    1);
+
+	cfg->q_state.paddr = cpu_to_le32(htt->tx_q_state.paddr);
+	cfg->q_state.num_peers = cpu_to_le16(htt->tx_q_state.num_peers);
+	cfg->q_state.num_tids = cpu_to_le16(htt->tx_q_state.num_tids);
+	cfg->q_state.record_size = HTT_TX_Q_STATE_ENTRY_SIZE;
+	cfg->q_state.record_multiplier = HTT_TX_Q_STATE_ENTRY_MULTIPLIER;
+
+	ath10k_dbg(ar, ATH10K_DBG_HTT, "htt frag desc bank cmd\n");
 
 	ret = ath10k_htc_send(&htt->ar->htc, htt->eid, skb);
 	if (ret) {
-- 
2.1.4

[PATCH 0/5] ath10k: add basic hostq support

[Michal Kazior]

There's a new firmware feature which uses a shared
DMA memory so host can share it's per-sta per-tid
queue size which is then subsequently used for
firmware to assist in deciding which frames to put
on the intermediate host-device tx queue.

This patchset adds only basic support to make
the firmware supporting the feature happy and
running at all. Without it firmware would freeze
shortly after booting.

More patches will follow some time later to add
the "new data path" logic.


v2:
 * fix gfp allocation [Ben]


Michal Kazior (5):
  ath10k: rename some HTT events
  ath10k: add new htt definitions
  ath10k: add new FW_FEATURE_PEER_FLOW_CONTROL
  ath10k: clean up cont frag desc init code
  ath10k: implement basic support for new tx path firmware

 drivers/net/wireless/ath/ath10k/core.c   |   1 +
 drivers/net/wireless/ath/ath10k/core.h   |   9 ++
 drivers/net/wireless/ath/ath10k/htt.c    |   8 +-
 drivers/net/wireless/ath/ath10k/htt.h    | 169 +++++++++++++++++++++++++++++--
 drivers/net/wireless/ath/ath10k/htt_rx.c |   8 +-
 drivers/net/wireless/ath/ath10k/htt_tx.c | 146 +++++++++++++++++++++-----
 6 files changed, 302 insertions(+), 39 deletions(-)

-- 
2.1.4


_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k

[PATCH 0/5] ath10k: add basic hostq support

[Michal Kazior]

There's a new firmware feature which uses a shared
DMA memory so host can share it's per-sta per-tid
queue size which is then subsequently used for
firmware to assist in deciding which frames to put
on the intermediate host-device tx queue.

This patchset adds only basic support to make
the firmware supporting the feature happy and
running at all. Without it firmware would freeze
shortly after booting.

More patches will follow some time later to add
the "new data path" logic.


v2:
 * fix gfp allocation [Ben]


Michal Kazior (5):
  ath10k: rename some HTT events
  ath10k: add new htt definitions
  ath10k: add new FW_FEATURE_PEER_FLOW_CONTROL
  ath10k: clean up cont frag desc init code
  ath10k: implement basic support for new tx path firmware

 drivers/net/wireless/ath/ath10k/core.c   |   1 +
 drivers/net/wireless/ath/ath10k/core.h   |   9 ++
 drivers/net/wireless/ath/ath10k/htt.c    |   8 +-
 drivers/net/wireless/ath/ath10k/htt.h    | 169 +++++++++++++++++++++++++++++--
 drivers/net/wireless/ath/ath10k/htt_rx.c |   8 +-
 drivers/net/wireless/ath/ath10k/htt_tx.c | 146 +++++++++++++++++++++-----
 6 files changed, 302 insertions(+), 39 deletions(-)

-- 
2.1.4

[PATCH 1/5] ath10k: rename some HTT events

[Michal Kazior]

New names make a bit more sense.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
---
 drivers/net/wireless/ath/ath10k/htt.c    | 8 ++++----
 drivers/net/wireless/ath/ath10k/htt.h    | 8 ++++----
 drivers/net/wireless/ath/ath10k/htt_rx.c | 4 ++--
 3 files changed, 10 insertions(+), 10 deletions(-)

diff --git a/drivers/net/wireless/ath/ath10k/htt.c b/drivers/net/wireless/ath/ath10k/htt.c
index 3e6ba63dfdff..7561f22f10f9 100644
--- a/drivers/net/wireless/ath/ath10k/htt.c
+++ b/drivers/net/wireless/ath/ath10k/htt.c
@@ -131,12 +131,12 @@ static const enum htt_t2h_msg_type htt_10_4_t2h_msg_types[] = {
 	[HTT_10_4_T2H_MSG_TYPE_AGGR_CONF] = HTT_T2H_MSG_TYPE_AGGR_CONF,
 	[HTT_10_4_T2H_MSG_TYPE_TX_FETCH_IND] =
 				HTT_T2H_MSG_TYPE_TX_FETCH_IND,
-	[HTT_10_4_T2H_MSG_TYPE_TX_FETCH_CONF] =
-				HTT_T2H_MSG_TYPE_TX_FETCH_CONF,
+	[HTT_10_4_T2H_MSG_TYPE_TX_FETCH_CONFIRM] =
+				HTT_T2H_MSG_TYPE_TX_FETCH_CONFIRM,
 	[HTT_10_4_T2H_MSG_TYPE_STATS_NOUPLOAD] =
 				HTT_T2H_MSG_TYPE_STATS_NOUPLOAD,
-	[HTT_10_4_T2H_MSG_TYPE_TX_LOW_LATENCY_IND] =
-				HTT_T2H_MSG_TYPE_TX_LOW_LATENCY_IND,
+	[HTT_10_4_T2H_MSG_TYPE_TX_MODE_SWITCH_IND] =
+				HTT_T2H_MSG_TYPE_TX_MODE_SWITCH_IND,
 };
 
 int ath10k_htt_connect(struct ath10k_htt *htt)
diff --git a/drivers/net/wireless/ath/ath10k/htt.h b/drivers/net/wireless/ath/ath10k/htt.h
index 47ca048feaf0..edd3b9070de9 100644
--- a/drivers/net/wireless/ath/ath10k/htt.h
+++ b/drivers/net/wireless/ath/ath10k/htt.h
@@ -413,10 +413,10 @@ enum htt_10_4_t2h_msg_type {
 	HTT_10_4_T2H_MSG_TYPE_EN_STATS               = 0x14,
 	HTT_10_4_T2H_MSG_TYPE_AGGR_CONF              = 0x15,
 	HTT_10_4_T2H_MSG_TYPE_TX_FETCH_IND           = 0x16,
-	HTT_10_4_T2H_MSG_TYPE_TX_FETCH_CONF          = 0x17,
+	HTT_10_4_T2H_MSG_TYPE_TX_FETCH_CONFIRM       = 0x17,
 	HTT_10_4_T2H_MSG_TYPE_STATS_NOUPLOAD         = 0x18,
 	/* 0x19 to 0x2f are reserved */
-	HTT_10_4_T2H_MSG_TYPE_TX_LOW_LATENCY_IND     = 0x30,
+	HTT_10_4_T2H_MSG_TYPE_TX_MODE_SWITCH_IND     = 0x30,
 	/* keep this last */
 	HTT_10_4_T2H_NUM_MSGS
 };
@@ -449,8 +449,8 @@ enum htt_t2h_msg_type {
 	HTT_T2H_MSG_TYPE_TEST,
 	HTT_T2H_MSG_TYPE_EN_STATS,
 	HTT_T2H_MSG_TYPE_TX_FETCH_IND,
-	HTT_T2H_MSG_TYPE_TX_FETCH_CONF,
-	HTT_T2H_MSG_TYPE_TX_LOW_LATENCY_IND,
+	HTT_T2H_MSG_TYPE_TX_FETCH_CONFIRM,
+	HTT_T2H_MSG_TYPE_TX_MODE_SWITCH_IND,
 	/* keep this last */
 	HTT_T2H_NUM_MSGS
 };
diff --git a/drivers/net/wireless/ath/ath10k/htt_rx.c b/drivers/net/wireless/ath/ath10k/htt_rx.c
index 91afa3ae414c..d923f64e4f42 100644
--- a/drivers/net/wireless/ath/ath10k/htt_rx.c
+++ b/drivers/net/wireless/ath/ath10k/htt_rx.c
@@ -2125,8 +2125,8 @@ void ath10k_htt_t2h_msg_handler(struct ath10k *ar, struct sk_buff *skb)
 		break;
 	case HTT_T2H_MSG_TYPE_EN_STATS:
 	case HTT_T2H_MSG_TYPE_TX_FETCH_IND:
-	case HTT_T2H_MSG_TYPE_TX_FETCH_CONF:
-	case HTT_T2H_MSG_TYPE_TX_LOW_LATENCY_IND:
+	case HTT_T2H_MSG_TYPE_TX_FETCH_CONFIRM:
+	case HTT_T2H_MSG_TYPE_TX_MODE_SWITCH_IND:
 	default:
 		ath10k_warn(ar, "htt event (%d) not handled\n",
 			    resp->hdr.msg_type);
-- 
2.1.4


_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k

[PATCH 1/5] ath10k: rename some HTT events

[Michal Kazior]

New names make a bit more sense.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
---
 drivers/net/wireless/ath/ath10k/htt.c    | 8 ++++----
 drivers/net/wireless/ath/ath10k/htt.h    | 8 ++++----
 drivers/net/wireless/ath/ath10k/htt_rx.c | 4 ++--
 3 files changed, 10 insertions(+), 10 deletions(-)

diff --git a/drivers/net/wireless/ath/ath10k/htt.c b/drivers/net/wireless/ath/ath10k/htt.c
index 3e6ba63dfdff..7561f22f10f9 100644
--- a/drivers/net/wireless/ath/ath10k/htt.c
+++ b/drivers/net/wireless/ath/ath10k/htt.c
@@ -131,12 +131,12 @@ static const enum htt_t2h_msg_type htt_10_4_t2h_msg_types[] = {
 	[HTT_10_4_T2H_MSG_TYPE_AGGR_CONF] = HTT_T2H_MSG_TYPE_AGGR_CONF,
 	[HTT_10_4_T2H_MSG_TYPE_TX_FETCH_IND] =
 				HTT_T2H_MSG_TYPE_TX_FETCH_IND,
-	[HTT_10_4_T2H_MSG_TYPE_TX_FETCH_CONF] =
-				HTT_T2H_MSG_TYPE_TX_FETCH_CONF,
+	[HTT_10_4_T2H_MSG_TYPE_TX_FETCH_CONFIRM] =
+				HTT_T2H_MSG_TYPE_TX_FETCH_CONFIRM,
 	[HTT_10_4_T2H_MSG_TYPE_STATS_NOUPLOAD] =
 				HTT_T2H_MSG_TYPE_STATS_NOUPLOAD,
-	[HTT_10_4_T2H_MSG_TYPE_TX_LOW_LATENCY_IND] =
-				HTT_T2H_MSG_TYPE_TX_LOW_LATENCY_IND,
+	[HTT_10_4_T2H_MSG_TYPE_TX_MODE_SWITCH_IND] =
+				HTT_T2H_MSG_TYPE_TX_MODE_SWITCH_IND,
 };
 
 int ath10k_htt_connect(struct ath10k_htt *htt)
diff --git a/drivers/net/wireless/ath/ath10k/htt.h b/drivers/net/wireless/ath/ath10k/htt.h
index 47ca048feaf0..edd3b9070de9 100644
--- a/drivers/net/wireless/ath/ath10k/htt.h
+++ b/drivers/net/wireless/ath/ath10k/htt.h
@@ -413,10 +413,10 @@ enum htt_10_4_t2h_msg_type {
 	HTT_10_4_T2H_MSG_TYPE_EN_STATS               = 0x14,
 	HTT_10_4_T2H_MSG_TYPE_AGGR_CONF              = 0x15,
 	HTT_10_4_T2H_MSG_TYPE_TX_FETCH_IND           = 0x16,
-	HTT_10_4_T2H_MSG_TYPE_TX_FETCH_CONF          = 0x17,
+	HTT_10_4_T2H_MSG_TYPE_TX_FETCH_CONFIRM       = 0x17,
 	HTT_10_4_T2H_MSG_TYPE_STATS_NOUPLOAD         = 0x18,
 	/* 0x19 to 0x2f are reserved */
-	HTT_10_4_T2H_MSG_TYPE_TX_LOW_LATENCY_IND     = 0x30,
+	HTT_10_4_T2H_MSG_TYPE_TX_MODE_SWITCH_IND     = 0x30,
 	/* keep this last */
 	HTT_10_4_T2H_NUM_MSGS
 };
@@ -449,8 +449,8 @@ enum htt_t2h_msg_type {
 	HTT_T2H_MSG_TYPE_TEST,
 	HTT_T2H_MSG_TYPE_EN_STATS,
 	HTT_T2H_MSG_TYPE_TX_FETCH_IND,
-	HTT_T2H_MSG_TYPE_TX_FETCH_CONF,
-	HTT_T2H_MSG_TYPE_TX_LOW_LATENCY_IND,
+	HTT_T2H_MSG_TYPE_TX_FETCH_CONFIRM,
+	HTT_T2H_MSG_TYPE_TX_MODE_SWITCH_IND,
 	/* keep this last */
 	HTT_T2H_NUM_MSGS
 };
diff --git a/drivers/net/wireless/ath/ath10k/htt_rx.c b/drivers/net/wireless/ath/ath10k/htt_rx.c
index 91afa3ae414c..d923f64e4f42 100644
--- a/drivers/net/wireless/ath/ath10k/htt_rx.c
+++ b/drivers/net/wireless/ath/ath10k/htt_rx.c
@@ -2125,8 +2125,8 @@ void ath10k_htt_t2h_msg_handler(struct ath10k *ar, struct sk_buff *skb)
 		break;
 	case HTT_T2H_MSG_TYPE_EN_STATS:
 	case HTT_T2H_MSG_TYPE_TX_FETCH_IND:
-	case HTT_T2H_MSG_TYPE_TX_FETCH_CONF:
-	case HTT_T2H_MSG_TYPE_TX_LOW_LATENCY_IND:
+	case HTT_T2H_MSG_TYPE_TX_FETCH_CONFIRM:
+	case HTT_T2H_MSG_TYPE_TX_MODE_SWITCH_IND:
 	default:
 		ath10k_warn(ar, "htt event (%d) not handled\n",
 			    resp->hdr.msg_type);
-- 
2.1.4

[PATCH 2/5] ath10k: add new htt definitions

[Michal Kazior]

These definitions are associated with some
improvements upcomming for 10.4 and QCA99X0.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
---
 drivers/net/wireless/ath/ath10k/htt.h | 153 +++++++++++++++++++++++++++++++++-
 1 file changed, 150 insertions(+), 3 deletions(-)

diff --git a/drivers/net/wireless/ath/ath10k/htt.h b/drivers/net/wireless/ath/ath10k/htt.h
index edd3b9070de9..0c5628dafabf 100644
--- a/drivers/net/wireless/ath/ath10k/htt.h
+++ b/drivers/net/wireless/ath/ath10k/htt.h
@@ -52,6 +52,7 @@ enum htt_h2t_msg_type { /* host-to-target */
 	/* This command is used for sending management frames in HTT < 3.0.
 	 * HTT >= 3.0 uses TX_FRM for everything. */
 	HTT_H2T_MSG_TYPE_MGMT_TX            = 7,
+	HTT_H2T_MSG_TYPE_TX_FETCH_RESP      = 11,
 
 	HTT_H2T_NUM_MSGS /* keep this last */
 };
@@ -1306,9 +1307,43 @@ struct htt_frag_desc_bank_id {
  * so we use a conservatively safe value for now */
 #define HTT_FRAG_DESC_BANK_MAX 4
 
-#define HTT_FRAG_DESC_BANK_CFG_INFO_PDEV_ID_MASK 0x03
-#define HTT_FRAG_DESC_BANK_CFG_INFO_PDEV_ID_LSB  0
-#define HTT_FRAG_DESC_BANK_CFG_INFO_SWAP         (1 << 2)
+#define HTT_FRAG_DESC_BANK_CFG_INFO_PDEV_ID_MASK		0x03
+#define HTT_FRAG_DESC_BANK_CFG_INFO_PDEV_ID_LSB			0
+#define HTT_FRAG_DESC_BANK_CFG_INFO_SWAP			BIT(2)
+#define HTT_FRAG_DESC_BANK_CFG_INFO_Q_STATE_VALID		BIT(3)
+#define HTT_FRAG_DESC_BANK_CFG_INFO_Q_STATE_DEPTH_TYPE_MASK	BIT(4)
+#define HTT_FRAG_DESC_BANK_CFG_INFO_Q_STATE_DEPTH_TYPE_LSB	4
+
+enum htt_q_depth_type {
+	HTT_Q_DEPTH_TYPE_BYTES = 0,
+	HTT_Q_DEPTH_TYPE_MSDUS = 1,
+};
+
+#define HTT_TX_Q_STATE_NUM_PEERS		(TARGET_10_4_NUM_QCACHE_PEERS_MAX + \
+						 TARGET_10_4_NUM_VDEVS)
+#define HTT_TX_Q_STATE_NUM_TIDS			8
+#define HTT_TX_Q_STATE_ENTRY_SIZE		1
+#define HTT_TX_Q_STATE_ENTRY_MULTIPLIER		0
+
+/**
+ * htt_q_state_conf - part of htt_frag_desc_bank_cfg for host q state config
+ *
+ * Defines host q state format and behavior. See htt_q_state.
+ *
+ * @record_size: Defines the size of each host q entry in bytes. In practice
+ *	however firmware (at least 10.4.3-00191) ignores this host
+ *	configuration value and uses hardcoded value of 1.
+ * @record_multiplier: This is valid only when q depth type is MSDUs. It
+ *	defines the exponent for the power of 2 multiplication.
+ */
+struct htt_q_state_conf {
+	__le32 paddr;
+	__le16 num_peers;
+	__le16 num_tids;
+	u8 record_size;
+	u8 record_multiplier;
+	u8 pad[2];
+} __packed;
 
 struct htt_frag_desc_bank_cfg {
 	u8 info; /* HTT_FRAG_DESC_BANK_CFG_INFO_ */
@@ -1316,6 +1351,114 @@ struct htt_frag_desc_bank_cfg {
 	u8 desc_size;
 	__le32 bank_base_addrs[HTT_FRAG_DESC_BANK_MAX];
 	struct htt_frag_desc_bank_id bank_id[HTT_FRAG_DESC_BANK_MAX];
+	struct htt_q_state_conf q_state;
+} __packed;
+
+#define HTT_TX_Q_STATE_ENTRY_COEFFICIENT	128
+#define HTT_TX_Q_STATE_ENTRY_FACTOR_MASK	0x3f
+#define HTT_TX_Q_STATE_ENTRY_FACTOR_LSB		0
+#define HTT_TX_Q_STATE_ENTRY_EXP_MASK		0xc0
+#define HTT_TX_Q_STATE_ENTRY_EXP_LSB		6
+
+/**
+ * htt_q_state - shared between host and firmware via DMA
+ *
+ * This structure is used for the host to expose it's software queue state to
+ * firmware so that its rate control can schedule fetch requests for optimized
+ * performance. This is most notably used for MU-MIMO aggregation when multiple
+ * MU clients are connected.
+ *
+ * @count: Each element defines the host queue depth. When q depth type was
+ *	configured as HTT_Q_DEPTH_TYPE_BYTES then each entry is defined as:
+ *	FACTOR * 128 * 8^EXP (see HTT_TX_Q_STATE_ENTRY_FACTOR_MASK and
+ *	HTT_TX_Q_STATE_ENTRY_EXP_MASK). When q depth type was configured as
+ *	HTT_Q_DEPTH_TYPE_MSDUS the number of packets is scaled by 2 **
+ *	record_multiplier (see htt_q_state_conf).
+ * @map: Used by firmware to quickly check which host queues are not empty. It
+ *	is a bitmap simply saying.
+ * @seq: Used by firmware to quickly check if the host queues were updated
+ *	since it last checked.
+ *
+ * FIXME: Is the q_state map[] size calculation really correct?
+ */
+struct htt_q_state {
+	u8 count[HTT_TX_Q_STATE_NUM_TIDS][HTT_TX_Q_STATE_NUM_PEERS];
+	u32 map[HTT_TX_Q_STATE_NUM_TIDS][(HTT_TX_Q_STATE_NUM_PEERS + 31) / 32];
+	__le32 seq;
+} __packed;
+
+#define HTT_TX_FETCH_RECORD_INFO_PEER_ID_MASK	0x0fff
+#define HTT_TX_FETCH_RECORD_INFO_PEER_ID_LSB	0
+#define HTT_TX_FETCH_RECORD_INFO_TID_MASK	0xf000
+#define HTT_TX_FETCH_RECORD_INFO_TID_LSB	12
+
+struct htt_tx_fetch_record {
+	__le16 info; /* HTT_TX_FETCH_IND_RECORD_INFO_ */
+	__le16 num_msdus;
+	__le32 num_bytes;
+} __packed;
+
+struct htt_tx_fetch_ind {
+	u8 pad0;
+	__le16 fetch_seq_num;
+	__le32 token;
+	__le16 num_resp_ids;
+	__le16 num_records;
+	struct htt_tx_fetch_record records[0];
+	__le32 resp_ids[0]; /* ath10k_htt_get_tx_fetch_ind_resp_ids() */
+} __packed;
+
+static inline void *
+ath10k_htt_get_tx_fetch_ind_resp_ids(struct htt_tx_fetch_ind *ind)
+{
+	return (void *)&ind->records[le16_to_cpu(ind->num_records)];
+}
+
+struct htt_tx_fetch_resp {
+	u8 pad0;
+	__le16 resp_id;
+	__le16 fetch_seq_num;
+	__le16 num_records;
+	__le32 token;
+	struct htt_tx_fetch_record records[0];
+} __packed;
+
+struct htt_tx_fetch_confirm {
+	u8 pad0;
+	__le16 num_resp_ids;
+	__le32 resp_ids[0];
+} __packed;
+
+enum htt_tx_mode_switch_mode {
+	HTT_TX_MODE_SWITCH_PUSH = 0,
+	HTT_TX_MODE_SWITCH_PUSH_PULL = 1,
+};
+
+#define HTT_TX_MODE_SWITCH_IND_INFO0_ENABLE		BIT(0)
+#define HTT_TX_MODE_SWITCH_IND_INFO0_NUM_RECORDS_MASK	0xfffe
+#define HTT_TX_MODE_SWITCH_IND_INFO0_NUM_RECORDS_LSB	1
+
+#define HTT_TX_MODE_SWITCH_IND_INFO1_MODE_MASK		0x0003
+#define HTT_TX_MODE_SWITCH_IND_INFO1_MODE_LSB		0
+#define HTT_TX_MODE_SWITCH_IND_INFO1_THRESHOLD_MASK	0xfffc
+#define HTT_TX_MODE_SWITCH_IND_INFO1_THRESHOLD_LSB	2
+
+#define HTT_TX_MODE_SWITCH_RECORD_INFO0_PEER_ID_MASK	0x0fff
+#define HTT_TX_MODE_SWITCH_RECORD_INFO0_PEER_ID_LSB	0
+#define HTT_TX_MODE_SWITCH_RECORD_INFO0_TID_MASK	0xf000
+#define HTT_TX_MODE_SWITCH_RECORD_INFO0_TID_LSB		12
+
+struct htt_tx_mode_switch_record {
+	__le16 info0; /* HTT_TX_MODE_SWITCH_RECORD_INFO0_ */
+	__le16 num_max_msdus;
+} __packed;
+
+struct htt_tx_mode_switch_ind {
+	u8 pad0;
+	__le16 info0; /* HTT_TX_MODE_SWITCH_IND_INFO0_ */
+	__le16 info1; /* HTT_TX_MODE_SWITCH_IND_INFO1_ */
+	u8 pad1[2];
+	struct htt_tx_mode_switch_record records[0];
 } __packed;
 
 union htt_rx_pn_t {
@@ -1340,6 +1483,7 @@ struct htt_cmd {
 		struct htt_oob_sync_req oob_sync_req;
 		struct htt_aggr_conf aggr_conf;
 		struct htt_frag_desc_bank_cfg frag_desc_bank_cfg;
+		struct htt_tx_fetch_resp tx_fetch_resp;
 	};
 } __packed;
 
@@ -1364,6 +1508,9 @@ struct htt_resp {
 		struct htt_rx_pn_ind rx_pn_ind;
 		struct htt_rx_offload_ind rx_offload_ind;
 		struct htt_rx_in_ord_ind rx_in_ord_ind;
+		struct htt_tx_fetch_ind tx_fetch_ind;
+		struct htt_tx_fetch_confirm tx_fetch_confirm;
+		struct htt_tx_mode_switch_ind tx_mode_switch_ind;
 	};
 } __packed;
 
-- 
2.1.4


_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k

[PATCH 2/5] ath10k: add new htt definitions

[Michal Kazior]

These definitions are associated with some
improvements upcomming for 10.4 and QCA99X0.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
---
 drivers/net/wireless/ath/ath10k/htt.h | 153 +++++++++++++++++++++++++++++++++-
 1 file changed, 150 insertions(+), 3 deletions(-)

diff --git a/drivers/net/wireless/ath/ath10k/htt.h b/drivers/net/wireless/ath/ath10k/htt.h
index edd3b9070de9..0c5628dafabf 100644
--- a/drivers/net/wireless/ath/ath10k/htt.h
+++ b/drivers/net/wireless/ath/ath10k/htt.h
@@ -52,6 +52,7 @@ enum htt_h2t_msg_type { /* host-to-target */
 	/* This command is used for sending management frames in HTT < 3.0.
 	 * HTT >= 3.0 uses TX_FRM for everything. */
 	HTT_H2T_MSG_TYPE_MGMT_TX            = 7,
+	HTT_H2T_MSG_TYPE_TX_FETCH_RESP      = 11,
 
 	HTT_H2T_NUM_MSGS /* keep this last */
 };
@@ -1306,9 +1307,43 @@ struct htt_frag_desc_bank_id {
  * so we use a conservatively safe value for now */
 #define HTT_FRAG_DESC_BANK_MAX 4
 
-#define HTT_FRAG_DESC_BANK_CFG_INFO_PDEV_ID_MASK 0x03
-#define HTT_FRAG_DESC_BANK_CFG_INFO_PDEV_ID_LSB  0
-#define HTT_FRAG_DESC_BANK_CFG_INFO_SWAP         (1 << 2)
+#define HTT_FRAG_DESC_BANK_CFG_INFO_PDEV_ID_MASK		0x03
+#define HTT_FRAG_DESC_BANK_CFG_INFO_PDEV_ID_LSB			0
+#define HTT_FRAG_DESC_BANK_CFG_INFO_SWAP			BIT(2)
+#define HTT_FRAG_DESC_BANK_CFG_INFO_Q_STATE_VALID		BIT(3)
+#define HTT_FRAG_DESC_BANK_CFG_INFO_Q_STATE_DEPTH_TYPE_MASK	BIT(4)
+#define HTT_FRAG_DESC_BANK_CFG_INFO_Q_STATE_DEPTH_TYPE_LSB	4
+
+enum htt_q_depth_type {
+	HTT_Q_DEPTH_TYPE_BYTES = 0,
+	HTT_Q_DEPTH_TYPE_MSDUS = 1,
+};
+
+#define HTT_TX_Q_STATE_NUM_PEERS		(TARGET_10_4_NUM_QCACHE_PEERS_MAX + \
+						 TARGET_10_4_NUM_VDEVS)
+#define HTT_TX_Q_STATE_NUM_TIDS			8
+#define HTT_TX_Q_STATE_ENTRY_SIZE		1
+#define HTT_TX_Q_STATE_ENTRY_MULTIPLIER		0
+
+/**
+ * htt_q_state_conf - part of htt_frag_desc_bank_cfg for host q state config
+ *
+ * Defines host q state format and behavior. See htt_q_state.
+ *
+ * @record_size: Defines the size of each host q entry in bytes. In practice
+ *	however firmware (at least 10.4.3-00191) ignores this host
+ *	configuration value and uses hardcoded value of 1.
+ * @record_multiplier: This is valid only when q depth type is MSDUs. It
+ *	defines the exponent for the power of 2 multiplication.
+ */
+struct htt_q_state_conf {
+	__le32 paddr;
+	__le16 num_peers;
+	__le16 num_tids;
+	u8 record_size;
+	u8 record_multiplier;
+	u8 pad[2];
+} __packed;
 
 struct htt_frag_desc_bank_cfg {
 	u8 info; /* HTT_FRAG_DESC_BANK_CFG_INFO_ */
@@ -1316,6 +1351,114 @@ struct htt_frag_desc_bank_cfg {
 	u8 desc_size;
 	__le32 bank_base_addrs[HTT_FRAG_DESC_BANK_MAX];
 	struct htt_frag_desc_bank_id bank_id[HTT_FRAG_DESC_BANK_MAX];
+	struct htt_q_state_conf q_state;
+} __packed;
+
+#define HTT_TX_Q_STATE_ENTRY_COEFFICIENT	128
+#define HTT_TX_Q_STATE_ENTRY_FACTOR_MASK	0x3f
+#define HTT_TX_Q_STATE_ENTRY_FACTOR_LSB		0
+#define HTT_TX_Q_STATE_ENTRY_EXP_MASK		0xc0
+#define HTT_TX_Q_STATE_ENTRY_EXP_LSB		6
+
+/**
+ * htt_q_state - shared between host and firmware via DMA
+ *
+ * This structure is used for the host to expose it's software queue state to
+ * firmware so that its rate control can schedule fetch requests for optimized
+ * performance. This is most notably used for MU-MIMO aggregation when multiple
+ * MU clients are connected.
+ *
+ * @count: Each element defines the host queue depth. When q depth type was
+ *	configured as HTT_Q_DEPTH_TYPE_BYTES then each entry is defined as:
+ *	FACTOR * 128 * 8^EXP (see HTT_TX_Q_STATE_ENTRY_FACTOR_MASK and
+ *	HTT_TX_Q_STATE_ENTRY_EXP_MASK). When q depth type was configured as
+ *	HTT_Q_DEPTH_TYPE_MSDUS the number of packets is scaled by 2 **
+ *	record_multiplier (see htt_q_state_conf).
+ * @map: Used by firmware to quickly check which host queues are not empty. It
+ *	is a bitmap simply saying.
+ * @seq: Used by firmware to quickly check if the host queues were updated
+ *	since it last checked.
+ *
+ * FIXME: Is the q_state map[] size calculation really correct?
+ */
+struct htt_q_state {
+	u8 count[HTT_TX_Q_STATE_NUM_TIDS][HTT_TX_Q_STATE_NUM_PEERS];
+	u32 map[HTT_TX_Q_STATE_NUM_TIDS][(HTT_TX_Q_STATE_NUM_PEERS + 31) / 32];
+	__le32 seq;
+} __packed;
+
+#define HTT_TX_FETCH_RECORD_INFO_PEER_ID_MASK	0x0fff
+#define HTT_TX_FETCH_RECORD_INFO_PEER_ID_LSB	0
+#define HTT_TX_FETCH_RECORD_INFO_TID_MASK	0xf000
+#define HTT_TX_FETCH_RECORD_INFO_TID_LSB	12
+
+struct htt_tx_fetch_record {
+	__le16 info; /* HTT_TX_FETCH_IND_RECORD_INFO_ */
+	__le16 num_msdus;
+	__le32 num_bytes;
+} __packed;
+
+struct htt_tx_fetch_ind {
+	u8 pad0;
+	__le16 fetch_seq_num;
+	__le32 token;
+	__le16 num_resp_ids;
+	__le16 num_records;
+	struct htt_tx_fetch_record records[0];
+	__le32 resp_ids[0]; /* ath10k_htt_get_tx_fetch_ind_resp_ids() */
+} __packed;
+
+static inline void *
+ath10k_htt_get_tx_fetch_ind_resp_ids(struct htt_tx_fetch_ind *ind)
+{
+	return (void *)&ind->records[le16_to_cpu(ind->num_records)];
+}
+
+struct htt_tx_fetch_resp {
+	u8 pad0;
+	__le16 resp_id;
+	__le16 fetch_seq_num;
+	__le16 num_records;
+	__le32 token;
+	struct htt_tx_fetch_record records[0];
+} __packed;
+
+struct htt_tx_fetch_confirm {
+	u8 pad0;
+	__le16 num_resp_ids;
+	__le32 resp_ids[0];
+} __packed;
+
+enum htt_tx_mode_switch_mode {
+	HTT_TX_MODE_SWITCH_PUSH = 0,
+	HTT_TX_MODE_SWITCH_PUSH_PULL = 1,
+};
+
+#define HTT_TX_MODE_SWITCH_IND_INFO0_ENABLE		BIT(0)
+#define HTT_TX_MODE_SWITCH_IND_INFO0_NUM_RECORDS_MASK	0xfffe
+#define HTT_TX_MODE_SWITCH_IND_INFO0_NUM_RECORDS_LSB	1
+
+#define HTT_TX_MODE_SWITCH_IND_INFO1_MODE_MASK		0x0003
+#define HTT_TX_MODE_SWITCH_IND_INFO1_MODE_LSB		0
+#define HTT_TX_MODE_SWITCH_IND_INFO1_THRESHOLD_MASK	0xfffc
+#define HTT_TX_MODE_SWITCH_IND_INFO1_THRESHOLD_LSB	2
+
+#define HTT_TX_MODE_SWITCH_RECORD_INFO0_PEER_ID_MASK	0x0fff
+#define HTT_TX_MODE_SWITCH_RECORD_INFO0_PEER_ID_LSB	0
+#define HTT_TX_MODE_SWITCH_RECORD_INFO0_TID_MASK	0xf000
+#define HTT_TX_MODE_SWITCH_RECORD_INFO0_TID_LSB		12
+
+struct htt_tx_mode_switch_record {
+	__le16 info0; /* HTT_TX_MODE_SWITCH_RECORD_INFO0_ */
+	__le16 num_max_msdus;
+} __packed;
+
+struct htt_tx_mode_switch_ind {
+	u8 pad0;
+	__le16 info0; /* HTT_TX_MODE_SWITCH_IND_INFO0_ */
+	__le16 info1; /* HTT_TX_MODE_SWITCH_IND_INFO1_ */
+	u8 pad1[2];
+	struct htt_tx_mode_switch_record records[0];
 } __packed;
 
 union htt_rx_pn_t {
@@ -1340,6 +1483,7 @@ struct htt_cmd {
 		struct htt_oob_sync_req oob_sync_req;
 		struct htt_aggr_conf aggr_conf;
 		struct htt_frag_desc_bank_cfg frag_desc_bank_cfg;
+		struct htt_tx_fetch_resp tx_fetch_resp;
 	};
 } __packed;
 
@@ -1364,6 +1508,9 @@ struct htt_resp {
 		struct htt_rx_pn_ind rx_pn_ind;
 		struct htt_rx_offload_ind rx_offload_ind;
 		struct htt_rx_in_ord_ind rx_in_ord_ind;
+		struct htt_tx_fetch_ind tx_fetch_ind;
+		struct htt_tx_fetch_confirm tx_fetch_confirm;
+		struct htt_tx_mode_switch_ind tx_mode_switch_ind;
 	};
 } __packed;
 
-- 
2.1.4

[PATCH 3/5] ath10k: add new FW_FEATURE_PEER_FLOW_CONTROL

[Michal Kazior]

This feature flag will be used for firmware which
supports pull-push model where host shares it's
software queue state with firmware and firmware
generates fetch requests telling host which queues
to dequeue tx from.

Primary function of this is improved MU-MIMO
performance with multiple clients.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
---
 drivers/net/wireless/ath/ath10k/core.c | 1 +
 drivers/net/wireless/ath/ath10k/core.h | 9 +++++++++
 2 files changed, 10 insertions(+)

diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c
index b41eb3f4ee56..48a26206c5c1 100644
--- a/drivers/net/wireless/ath/ath10k/core.c
+++ b/drivers/net/wireless/ath/ath10k/core.c
@@ -217,6 +217,7 @@ static const char *const ath10k_core_fw_feature_str[] = {
 	[ATH10K_FW_FEATURE_RAW_MODE_SUPPORT] = "raw-mode",
 	[ATH10K_FW_FEATURE_SUPPORTS_ADAPTIVE_CCA] = "adaptive-cca",
 	[ATH10K_FW_FEATURE_MFP_SUPPORT] = "mfp",
+	[ATH10K_FW_FEATURE_PEER_FLOW_CONTROL] = "peer-flow-ctrl",
 };
 
 static unsigned int ath10k_core_get_fw_feature_str(char *buf,
diff --git a/drivers/net/wireless/ath/ath10k/core.h b/drivers/net/wireless/ath/ath10k/core.h
index 7840cf3ef7a6..822e3195533a 100644
--- a/drivers/net/wireless/ath/ath10k/core.h
+++ b/drivers/net/wireless/ath/ath10k/core.h
@@ -510,6 +510,15 @@ enum ath10k_fw_features {
 	/* Firmware supports management frame protection */
 	ATH10K_FW_FEATURE_MFP_SUPPORT = 12,
 
+	/* Firmware supports pull-push model where host shares it's software
+	 * queue state with firmware and firmware generates fetch requests
+	 * telling host which queues to dequeue tx from.
+	 *
+	 * Primary function of this is improved MU-MIMO performance with
+	 * multiple clients.
+	 */
+	ATH10K_FW_FEATURE_PEER_FLOW_CONTROL = 13,
+
 	/* keep last */
 	ATH10K_FW_FEATURE_COUNT,
 };
-- 
2.1.4


_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k

[PATCH 3/5] ath10k: add new FW_FEATURE_PEER_FLOW_CONTROL

[Michal Kazior]

This feature flag will be used for firmware which
supports pull-push model where host shares it's
software queue state with firmware and firmware
generates fetch requests telling host which queues
to dequeue tx from.

Primary function of this is improved MU-MIMO
performance with multiple clients.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
---
 drivers/net/wireless/ath/ath10k/core.c | 1 +
 drivers/net/wireless/ath/ath10k/core.h | 9 +++++++++
 2 files changed, 10 insertions(+)

diff --git a/drivers/net/wireless/ath/ath10k/core.c b/drivers/net/wireless/ath/ath10k/core.c
index b41eb3f4ee56..48a26206c5c1 100644
--- a/drivers/net/wireless/ath/ath10k/core.c
+++ b/drivers/net/wireless/ath/ath10k/core.c
@@ -217,6 +217,7 @@ static const char *const ath10k_core_fw_feature_str[] = {
 	[ATH10K_FW_FEATURE_RAW_MODE_SUPPORT] = "raw-mode",
 	[ATH10K_FW_FEATURE_SUPPORTS_ADAPTIVE_CCA] = "adaptive-cca",
 	[ATH10K_FW_FEATURE_MFP_SUPPORT] = "mfp",
+	[ATH10K_FW_FEATURE_PEER_FLOW_CONTROL] = "peer-flow-ctrl",
 };
 
 static unsigned int ath10k_core_get_fw_feature_str(char *buf,
diff --git a/drivers/net/wireless/ath/ath10k/core.h b/drivers/net/wireless/ath/ath10k/core.h
index 7840cf3ef7a6..822e3195533a 100644
--- a/drivers/net/wireless/ath/ath10k/core.h
+++ b/drivers/net/wireless/ath/ath10k/core.h
@@ -510,6 +510,15 @@ enum ath10k_fw_features {
 	/* Firmware supports management frame protection */
 	ATH10K_FW_FEATURE_MFP_SUPPORT = 12,
 
+	/* Firmware supports pull-push model where host shares it's software
+	 * queue state with firmware and firmware generates fetch requests
+	 * telling host which queues to dequeue tx from.
+	 *
+	 * Primary function of this is improved MU-MIMO performance with
+	 * multiple clients.
+	 */
+	ATH10K_FW_FEATURE_PEER_FLOW_CONTROL = 13,
+
 	/* keep last */
 	ATH10K_FW_FEATURE_COUNT,
 };
-- 
2.1.4

[PATCH 4/5] ath10k: clean up cont frag desc init code

[Michal Kazior]

This makes the code easier to extend and re-use.

While at it fix _warn to _err. Other than that
there are no functional changes.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
---

Notes:
    v2:
     * fix gfp allocation [Ben]

 drivers/net/wireless/ath/ath10k/htt_tx.c | 58 ++++++++++++++++++++++----------
 1 file changed, 41 insertions(+), 17 deletions(-)

diff --git a/drivers/net/wireless/ath/ath10k/htt_tx.c b/drivers/net/wireless/ath/ath10k/htt_tx.c
index b3adadb5f824..28b8d7af8506 100644
--- a/drivers/net/wireless/ath/ath10k/htt_tx.c
+++ b/drivers/net/wireless/ath/ath10k/htt_tx.c
@@ -97,6 +97,41 @@ void ath10k_htt_tx_free_msdu_id(struct ath10k_htt *htt, u16 msdu_id)
 	idr_remove(&htt->pending_tx, msdu_id);
 }
 
+static void ath10k_htt_tx_free_cont_frag_desc(struct ath10k_htt *htt)
+{
+	size_t size;
+
+	if (!htt->frag_desc.vaddr)
+		return;
+
+	size = htt->max_num_pending_tx * sizeof(struct htt_msdu_ext_desc);
+
+	dma_free_coherent(htt->ar->dev,
+			  size,
+			  htt->frag_desc.vaddr,
+			  htt->frag_desc.paddr);
+}
+
+static int ath10k_htt_tx_alloc_cont_frag_desc(struct ath10k_htt *htt)
+{
+	struct ath10k *ar = htt->ar;
+	size_t size;
+
+	if (!ar->hw_params.continuous_frag_desc)
+		return 0;
+
+	size = htt->max_num_pending_tx * sizeof(struct htt_msdu_ext_desc);
+	htt->frag_desc.vaddr = dma_alloc_coherent(ar->dev, size,
+						  &htt->frag_desc.paddr,
+						  GFP_KERNEL);
+	if (!htt->frag_desc.vaddr) {
+		ath10k_err(ar, "failed to alloc fragment desc memory\n");
+		return -ENOMEM;
+	}
+
+	return 0;
+}
+
 int ath10k_htt_tx_alloc(struct ath10k_htt *htt)
 {
 	struct ath10k *ar = htt->ar;
@@ -118,20 +153,12 @@ int ath10k_htt_tx_alloc(struct ath10k_htt *htt)
 		goto free_idr_pending_tx;
 	}
 
-	if (!ar->hw_params.continuous_frag_desc)
-		goto skip_frag_desc_alloc;
-
-	size = htt->max_num_pending_tx * sizeof(struct htt_msdu_ext_desc);
-	htt->frag_desc.vaddr = dma_alloc_coherent(ar->dev, size,
-						  &htt->frag_desc.paddr,
-						  GFP_KERNEL);
-	if (!htt->frag_desc.vaddr) {
-		ath10k_warn(ar, "failed to alloc fragment desc memory\n");
-		ret = -ENOMEM;
+	ret = ath10k_htt_tx_alloc_cont_frag_desc(htt);
+	if (ret) {
+		ath10k_err(ar, "failed to alloc cont frag desc: %d\n", ret);
 		goto free_txbuf;
 	}
 
-skip_frag_desc_alloc:
 	return 0;
 
 free_txbuf:
@@ -139,8 +166,10 @@ free_txbuf:
 			  sizeof(struct ath10k_htt_txbuf);
 	dma_free_coherent(htt->ar->dev, size, htt->txbuf.vaddr,
 			  htt->txbuf.paddr);
+
 free_idr_pending_tx:
 	idr_destroy(&htt->pending_tx);
+
 	return ret;
 }
 
@@ -174,12 +203,7 @@ void ath10k_htt_tx_free(struct ath10k_htt *htt)
 				  htt->txbuf.paddr);
 	}
 
-	if (htt->frag_desc.vaddr) {
-		size = htt->max_num_pending_tx *
-				  sizeof(struct htt_msdu_ext_desc);
-		dma_free_coherent(htt->ar->dev, size, htt->frag_desc.vaddr,
-				  htt->frag_desc.paddr);
-	}
+	ath10k_htt_tx_free_cont_frag_desc(htt);
 }
 
 void ath10k_htt_htc_tx_complete(struct ath10k *ar, struct sk_buff *skb)
-- 
2.1.4


_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k

[PATCH 4/5] ath10k: clean up cont frag desc init code

[Michal Kazior]

This makes the code easier to extend and re-use.

While at it fix _warn to _err. Other than that
there are no functional changes.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
---

Notes:
    v2:
     * fix gfp allocation [Ben]

 drivers/net/wireless/ath/ath10k/htt_tx.c | 58 ++++++++++++++++++++++----------
 1 file changed, 41 insertions(+), 17 deletions(-)

diff --git a/drivers/net/wireless/ath/ath10k/htt_tx.c b/drivers/net/wireless/ath/ath10k/htt_tx.c
index b3adadb5f824..28b8d7af8506 100644
--- a/drivers/net/wireless/ath/ath10k/htt_tx.c
+++ b/drivers/net/wireless/ath/ath10k/htt_tx.c
@@ -97,6 +97,41 @@ void ath10k_htt_tx_free_msdu_id(struct ath10k_htt *htt, u16 msdu_id)
 	idr_remove(&htt->pending_tx, msdu_id);
 }
 
+static void ath10k_htt_tx_free_cont_frag_desc(struct ath10k_htt *htt)
+{
+	size_t size;
+
+	if (!htt->frag_desc.vaddr)
+		return;
+
+	size = htt->max_num_pending_tx * sizeof(struct htt_msdu_ext_desc);
+
+	dma_free_coherent(htt->ar->dev,
+			  size,
+			  htt->frag_desc.vaddr,
+			  htt->frag_desc.paddr);
+}
+
+static int ath10k_htt_tx_alloc_cont_frag_desc(struct ath10k_htt *htt)
+{
+	struct ath10k *ar = htt->ar;
+	size_t size;
+
+	if (!ar->hw_params.continuous_frag_desc)
+		return 0;
+
+	size = htt->max_num_pending_tx * sizeof(struct htt_msdu_ext_desc);
+	htt->frag_desc.vaddr = dma_alloc_coherent(ar->dev, size,
+						  &htt->frag_desc.paddr,
+						  GFP_KERNEL);
+	if (!htt->frag_desc.vaddr) {
+		ath10k_err(ar, "failed to alloc fragment desc memory\n");
+		return -ENOMEM;
+	}
+
+	return 0;
+}
+
 int ath10k_htt_tx_alloc(struct ath10k_htt *htt)
 {
 	struct ath10k *ar = htt->ar;
@@ -118,20 +153,12 @@ int ath10k_htt_tx_alloc(struct ath10k_htt *htt)
 		goto free_idr_pending_tx;
 	}
 
-	if (!ar->hw_params.continuous_frag_desc)
-		goto skip_frag_desc_alloc;
-
-	size = htt->max_num_pending_tx * sizeof(struct htt_msdu_ext_desc);
-	htt->frag_desc.vaddr = dma_alloc_coherent(ar->dev, size,
-						  &htt->frag_desc.paddr,
-						  GFP_KERNEL);
-	if (!htt->frag_desc.vaddr) {
-		ath10k_warn(ar, "failed to alloc fragment desc memory\n");
-		ret = -ENOMEM;
+	ret = ath10k_htt_tx_alloc_cont_frag_desc(htt);
+	if (ret) {
+		ath10k_err(ar, "failed to alloc cont frag desc: %d\n", ret);
 		goto free_txbuf;
 	}
 
-skip_frag_desc_alloc:
 	return 0;
 
 free_txbuf:
@@ -139,8 +166,10 @@ free_txbuf:
 			  sizeof(struct ath10k_htt_txbuf);
 	dma_free_coherent(htt->ar->dev, size, htt->txbuf.vaddr,
 			  htt->txbuf.paddr);
+
 free_idr_pending_tx:
 	idr_destroy(&htt->pending_tx);
+
 	return ret;
 }
 
@@ -174,12 +203,7 @@ void ath10k_htt_tx_free(struct ath10k_htt *htt)
 				  htt->txbuf.paddr);
 	}
 
-	if (htt->frag_desc.vaddr) {
-		size = htt->max_num_pending_tx *
-				  sizeof(struct htt_msdu_ext_desc);
-		dma_free_coherent(htt->ar->dev, size, htt->frag_desc.vaddr,
-				  htt->frag_desc.paddr);
-	}
+	ath10k_htt_tx_free_cont_frag_desc(htt);
 }
 
 void ath10k_htt_htc_tx_complete(struct ath10k *ar, struct sk_buff *skb)
-- 
2.1.4

[PATCH 5/5] ath10k: implement basic support for new tx path firmware

[Michal Kazior]

This allows to use the new firmware which
implements the new tx data path. Without this
patch firmware supporting new tx path stops
responding shortly after booting.

This patch doesn't implement the entire pull-push
logic available in the new firmware. This will be
done in subsequent patches.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
---
 drivers/net/wireless/ath/ath10k/htt.h    |  8 +++
 drivers/net/wireless/ath/ath10k/htt_rx.c |  4 +-
 drivers/net/wireless/ath/ath10k/htt_tx.c | 88 +++++++++++++++++++++++++++++---
 3 files changed, 91 insertions(+), 9 deletions(-)

diff --git a/drivers/net/wireless/ath/ath10k/htt.h b/drivers/net/wireless/ath/ath10k/htt.h
index 0c5628dafabf..13391ea4422d 100644
--- a/drivers/net/wireless/ath/ath10k/htt.h
+++ b/drivers/net/wireless/ath/ath10k/htt.h
@@ -1665,6 +1665,14 @@ struct ath10k_htt {
 		dma_addr_t paddr;
 		struct ath10k_htt_txbuf *vaddr;
 	} txbuf;
+
+	struct {
+		struct htt_q_state *vaddr;
+		dma_addr_t paddr;
+		u16 num_peers;
+		u16 num_tids;
+		enum htt_q_depth_type type;
+	} tx_q_state;
 };
 
 #define RX_HTT_HDR_STATUS_LEN 64
diff --git a/drivers/net/wireless/ath/ath10k/htt_rx.c b/drivers/net/wireless/ath/ath10k/htt_rx.c
index d923f64e4f42..248405b53ef4 100644
--- a/drivers/net/wireless/ath/ath10k/htt_rx.c
+++ b/drivers/net/wireless/ath/ath10k/htt_rx.c
@@ -2123,10 +2123,12 @@ void ath10k_htt_t2h_msg_handler(struct ath10k *ar, struct sk_buff *skb)
 		break;
 	case HTT_T2H_MSG_TYPE_AGGR_CONF:
 		break;
-	case HTT_T2H_MSG_TYPE_EN_STATS:
 	case HTT_T2H_MSG_TYPE_TX_FETCH_IND:
 	case HTT_T2H_MSG_TYPE_TX_FETCH_CONFIRM:
 	case HTT_T2H_MSG_TYPE_TX_MODE_SWITCH_IND:
+		/* TODO: Implement pull-push logic */
+		break;
+	case HTT_T2H_MSG_TYPE_EN_STATS:
 	default:
 		ath10k_warn(ar, "htt event (%d) not handled\n",
 			    resp->hdr.msg_type);
diff --git a/drivers/net/wireless/ath/ath10k/htt_tx.c b/drivers/net/wireless/ath/ath10k/htt_tx.c
index 28b8d7af8506..95acb727c068 100644
--- a/drivers/net/wireless/ath/ath10k/htt_tx.c
+++ b/drivers/net/wireless/ath/ath10k/htt_tx.c
@@ -132,6 +132,50 @@ static int ath10k_htt_tx_alloc_cont_frag_desc(struct ath10k_htt *htt)
 	return 0;
 }
 
+static void ath10k_htt_tx_free_txq(struct ath10k_htt *htt)
+{
+	struct ath10k *ar = htt->ar;
+	size_t size;
+
+	if (!test_bit(ATH10K_FW_FEATURE_PEER_FLOW_CONTROL, ar->fw_features))
+		return;
+
+	size = sizeof(*htt->tx_q_state.vaddr);
+
+	dma_unmap_single(ar->dev, htt->tx_q_state.paddr, size, DMA_TO_DEVICE);
+	kfree(htt->tx_q_state.vaddr);
+}
+
+static int ath10k_htt_tx_alloc_txq(struct ath10k_htt *htt)
+{
+	struct ath10k *ar = htt->ar;
+	size_t size;
+	int ret;
+
+	if (!test_bit(ATH10K_FW_FEATURE_PEER_FLOW_CONTROL, ar->fw_features))
+		return 0;
+
+	htt->tx_q_state.num_peers = HTT_TX_Q_STATE_NUM_PEERS;
+	htt->tx_q_state.num_tids = HTT_TX_Q_STATE_NUM_TIDS;
+	htt->tx_q_state.type = HTT_Q_DEPTH_TYPE_BYTES;
+
+	size = sizeof(*htt->tx_q_state.vaddr);
+	htt->tx_q_state.vaddr = kzalloc(size, GFP_KERNEL);
+	if (!htt->tx_q_state.vaddr)
+		return -ENOMEM;
+
+	htt->tx_q_state.paddr = dma_map_single(ar->dev, htt->tx_q_state.vaddr,
+					       size, DMA_TO_DEVICE);
+	ret = dma_mapping_error(ar->dev, htt->tx_q_state.paddr);
+	if (ret) {
+		ath10k_warn(ar, "failed to dma map tx_q_state: %d\n", ret);
+		kfree(htt->tx_q_state.vaddr);
+		return -EIO;
+	}
+
+	return 0;
+}
+
 int ath10k_htt_tx_alloc(struct ath10k_htt *htt)
 {
 	struct ath10k *ar = htt->ar;
@@ -159,8 +203,17 @@ int ath10k_htt_tx_alloc(struct ath10k_htt *htt)
 		goto free_txbuf;
 	}
 
+	ret = ath10k_htt_tx_alloc_txq(htt);
+	if (ret) {
+		ath10k_err(ar, "failed to alloc txq: %d\n", ret);
+		goto free_frag_desc;
+	}
+
 	return 0;
 
+free_frag_desc:
+	ath10k_htt_tx_free_cont_frag_desc(htt);
+
 free_txbuf:
 	size = htt->max_num_pending_tx *
 			  sizeof(struct ath10k_htt_txbuf);
@@ -203,6 +256,7 @@ void ath10k_htt_tx_free(struct ath10k_htt *htt)
 				  htt->txbuf.paddr);
 	}
 
+	ath10k_htt_tx_free_txq(htt);
 	ath10k_htt_tx_free_cont_frag_desc(htt);
 }
 
@@ -292,7 +346,9 @@ int ath10k_htt_send_frag_desc_bank_cfg(struct ath10k_htt *htt)
 	struct ath10k *ar = htt->ar;
 	struct sk_buff *skb;
 	struct htt_cmd *cmd;
+	struct htt_frag_desc_bank_cfg *cfg;
 	int ret, size;
+	u8 info;
 
 	if (!ar->hw_params.continuous_frag_desc)
 		return 0;
@@ -310,14 +366,30 @@ int ath10k_htt_send_frag_desc_bank_cfg(struct ath10k_htt *htt)
 	skb_put(skb, size);
 	cmd = (struct htt_cmd *)skb->data;
 	cmd->hdr.msg_type = HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG;
-	cmd->frag_desc_bank_cfg.info = 0;
-	cmd->frag_desc_bank_cfg.num_banks = 1;
-	cmd->frag_desc_bank_cfg.desc_size = sizeof(struct htt_msdu_ext_desc);
-	cmd->frag_desc_bank_cfg.bank_base_addrs[0] =
-				__cpu_to_le32(htt->frag_desc.paddr);
-	cmd->frag_desc_bank_cfg.bank_id[0].bank_min_id = 0;
-	cmd->frag_desc_bank_cfg.bank_id[0].bank_max_id =
-				__cpu_to_le16(htt->max_num_pending_tx - 1);
+
+	info = 0;
+	info |= SM(htt->tx_q_state.type,
+		   HTT_FRAG_DESC_BANK_CFG_INFO_Q_STATE_DEPTH_TYPE);
+
+	if (test_bit(ATH10K_FW_FEATURE_PEER_FLOW_CONTROL, ar->fw_features))
+		info |= HTT_FRAG_DESC_BANK_CFG_INFO_Q_STATE_VALID;
+
+	cfg = &cmd->frag_desc_bank_cfg;
+	cfg->info = info;
+	cfg->num_banks = 1;
+	cfg->desc_size = sizeof(struct htt_msdu_ext_desc);
+	cfg->bank_base_addrs[0] = __cpu_to_le32(htt->frag_desc.paddr);
+	cfg->bank_id[0].bank_min_id = 0;
+	cfg->bank_id[0].bank_max_id = __cpu_to_le16(htt->max_num_pending_tx -
+						    1);
+
+	cfg->q_state.paddr = cpu_to_le32(htt->tx_q_state.paddr);
+	cfg->q_state.num_peers = cpu_to_le16(htt->tx_q_state.num_peers);
+	cfg->q_state.num_tids = cpu_to_le16(htt->tx_q_state.num_tids);
+	cfg->q_state.record_size = HTT_TX_Q_STATE_ENTRY_SIZE;
+	cfg->q_state.record_multiplier = HTT_TX_Q_STATE_ENTRY_MULTIPLIER;
+
+	ath10k_dbg(ar, ATH10K_DBG_HTT, "htt frag desc bank cmd\n");
 
 	ret = ath10k_htc_send(&htt->ar->htc, htt->eid, skb);
 	if (ret) {
-- 
2.1.4


_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k

[PATCH 5/5] ath10k: implement basic support for new tx path firmware

[Michal Kazior]

This allows to use the new firmware which
implements the new tx data path. Without this
patch firmware supporting new tx path stops
responding shortly after booting.

This patch doesn't implement the entire pull-push
logic available in the new firmware. This will be
done in subsequent patches.

Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
---
 drivers/net/wireless/ath/ath10k/htt.h    |  8 +++
 drivers/net/wireless/ath/ath10k/htt_rx.c |  4 +-
 drivers/net/wireless/ath/ath10k/htt_tx.c | 88 +++++++++++++++++++++++++++++---
 3 files changed, 91 insertions(+), 9 deletions(-)

diff --git a/drivers/net/wireless/ath/ath10k/htt.h b/drivers/net/wireless/ath/ath10k/htt.h
index 0c5628dafabf..13391ea4422d 100644
--- a/drivers/net/wireless/ath/ath10k/htt.h
+++ b/drivers/net/wireless/ath/ath10k/htt.h
@@ -1665,6 +1665,14 @@ struct ath10k_htt {
 		dma_addr_t paddr;
 		struct ath10k_htt_txbuf *vaddr;
 	} txbuf;
+
+	struct {
+		struct htt_q_state *vaddr;
+		dma_addr_t paddr;
+		u16 num_peers;
+		u16 num_tids;
+		enum htt_q_depth_type type;
+	} tx_q_state;
 };
 
 #define RX_HTT_HDR_STATUS_LEN 64
diff --git a/drivers/net/wireless/ath/ath10k/htt_rx.c b/drivers/net/wireless/ath/ath10k/htt_rx.c
index d923f64e4f42..248405b53ef4 100644
--- a/drivers/net/wireless/ath/ath10k/htt_rx.c
+++ b/drivers/net/wireless/ath/ath10k/htt_rx.c
@@ -2123,10 +2123,12 @@ void ath10k_htt_t2h_msg_handler(struct ath10k *ar, struct sk_buff *skb)
 		break;
 	case HTT_T2H_MSG_TYPE_AGGR_CONF:
 		break;
-	case HTT_T2H_MSG_TYPE_EN_STATS:
 	case HTT_T2H_MSG_TYPE_TX_FETCH_IND:
 	case HTT_T2H_MSG_TYPE_TX_FETCH_CONFIRM:
 	case HTT_T2H_MSG_TYPE_TX_MODE_SWITCH_IND:
+		/* TODO: Implement pull-push logic */
+		break;
+	case HTT_T2H_MSG_TYPE_EN_STATS:
 	default:
 		ath10k_warn(ar, "htt event (%d) not handled\n",
 			    resp->hdr.msg_type);
diff --git a/drivers/net/wireless/ath/ath10k/htt_tx.c b/drivers/net/wireless/ath/ath10k/htt_tx.c
index 28b8d7af8506..95acb727c068 100644
--- a/drivers/net/wireless/ath/ath10k/htt_tx.c
+++ b/drivers/net/wireless/ath/ath10k/htt_tx.c
@@ -132,6 +132,50 @@ static int ath10k_htt_tx_alloc_cont_frag_desc(struct ath10k_htt *htt)
 	return 0;
 }
 
+static void ath10k_htt_tx_free_txq(struct ath10k_htt *htt)
+{
+	struct ath10k *ar = htt->ar;
+	size_t size;
+
+	if (!test_bit(ATH10K_FW_FEATURE_PEER_FLOW_CONTROL, ar->fw_features))
+		return;
+
+	size = sizeof(*htt->tx_q_state.vaddr);
+
+	dma_unmap_single(ar->dev, htt->tx_q_state.paddr, size, DMA_TO_DEVICE);
+	kfree(htt->tx_q_state.vaddr);
+}
+
+static int ath10k_htt_tx_alloc_txq(struct ath10k_htt *htt)
+{
+	struct ath10k *ar = htt->ar;
+	size_t size;
+	int ret;
+
+	if (!test_bit(ATH10K_FW_FEATURE_PEER_FLOW_CONTROL, ar->fw_features))
+		return 0;
+
+	htt->tx_q_state.num_peers = HTT_TX_Q_STATE_NUM_PEERS;
+	htt->tx_q_state.num_tids = HTT_TX_Q_STATE_NUM_TIDS;
+	htt->tx_q_state.type = HTT_Q_DEPTH_TYPE_BYTES;
+
+	size = sizeof(*htt->tx_q_state.vaddr);
+	htt->tx_q_state.vaddr = kzalloc(size, GFP_KERNEL);
+	if (!htt->tx_q_state.vaddr)
+		return -ENOMEM;
+
+	htt->tx_q_state.paddr = dma_map_single(ar->dev, htt->tx_q_state.vaddr,
+					       size, DMA_TO_DEVICE);
+	ret = dma_mapping_error(ar->dev, htt->tx_q_state.paddr);
+	if (ret) {
+		ath10k_warn(ar, "failed to dma map tx_q_state: %d\n", ret);
+		kfree(htt->tx_q_state.vaddr);
+		return -EIO;
+	}
+
+	return 0;
+}
+
 int ath10k_htt_tx_alloc(struct ath10k_htt *htt)
 {
 	struct ath10k *ar = htt->ar;
@@ -159,8 +203,17 @@ int ath10k_htt_tx_alloc(struct ath10k_htt *htt)
 		goto free_txbuf;
 	}
 
+	ret = ath10k_htt_tx_alloc_txq(htt);
+	if (ret) {
+		ath10k_err(ar, "failed to alloc txq: %d\n", ret);
+		goto free_frag_desc;
+	}
+
 	return 0;
 
+free_frag_desc:
+	ath10k_htt_tx_free_cont_frag_desc(htt);
+
 free_txbuf:
 	size = htt->max_num_pending_tx *
 			  sizeof(struct ath10k_htt_txbuf);
@@ -203,6 +256,7 @@ void ath10k_htt_tx_free(struct ath10k_htt *htt)
 				  htt->txbuf.paddr);
 	}
 
+	ath10k_htt_tx_free_txq(htt);
 	ath10k_htt_tx_free_cont_frag_desc(htt);
 }
 
@@ -292,7 +346,9 @@ int ath10k_htt_send_frag_desc_bank_cfg(struct ath10k_htt *htt)
 	struct ath10k *ar = htt->ar;
 	struct sk_buff *skb;
 	struct htt_cmd *cmd;
+	struct htt_frag_desc_bank_cfg *cfg;
 	int ret, size;
+	u8 info;
 
 	if (!ar->hw_params.continuous_frag_desc)
 		return 0;
@@ -310,14 +366,30 @@ int ath10k_htt_send_frag_desc_bank_cfg(struct ath10k_htt *htt)
 	skb_put(skb, size);
 	cmd = (struct htt_cmd *)skb->data;
 	cmd->hdr.msg_type = HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG;
-	cmd->frag_desc_bank_cfg.info = 0;
-	cmd->frag_desc_bank_cfg.num_banks = 1;
-	cmd->frag_desc_bank_cfg.desc_size = sizeof(struct htt_msdu_ext_desc);
-	cmd->frag_desc_bank_cfg.bank_base_addrs[0] =
-				__cpu_to_le32(htt->frag_desc.paddr);
-	cmd->frag_desc_bank_cfg.bank_id[0].bank_min_id = 0;
-	cmd->frag_desc_bank_cfg.bank_id[0].bank_max_id =
-				__cpu_to_le16(htt->max_num_pending_tx - 1);
+
+	info = 0;
+	info |= SM(htt->tx_q_state.type,
+		   HTT_FRAG_DESC_BANK_CFG_INFO_Q_STATE_DEPTH_TYPE);
+
+	if (test_bit(ATH10K_FW_FEATURE_PEER_FLOW_CONTROL, ar->fw_features))
+		info |= HTT_FRAG_DESC_BANK_CFG_INFO_Q_STATE_VALID;
+
+	cfg = &cmd->frag_desc_bank_cfg;
+	cfg->info = info;
+	cfg->num_banks = 1;
+	cfg->desc_size = sizeof(struct htt_msdu_ext_desc);
+	cfg->bank_base_addrs[0] = __cpu_to_le32(htt->frag_desc.paddr);
+	cfg->bank_id[0].bank_min_id = 0;
+	cfg->bank_id[0].bank_max_id = __cpu_to_le16(htt->max_num_pending_tx -
+						    1);
+
+	cfg->q_state.paddr = cpu_to_le32(htt->tx_q_state.paddr);
+	cfg->q_state.num_peers = cpu_to_le16(htt->tx_q_state.num_peers);
+	cfg->q_state.num_tids = cpu_to_le16(htt->tx_q_state.num_tids);
+	cfg->q_state.record_size = HTT_TX_Q_STATE_ENTRY_SIZE;
+	cfg->q_state.record_multiplier = HTT_TX_Q_STATE_ENTRY_MULTIPLIER;
+
+	ath10k_dbg(ar, ATH10K_DBG_HTT, "htt frag desc bank cmd\n");
 
 	ret = ath10k_htc_send(&htt->ar->htc, htt->eid, skb);
 	if (ret) {
-- 
2.1.4

Re: [PATCH 0/5] ath10k: add basic hostq support

[Michal Kazior]

On 21 January 2016 at 14:13, Michal Kazior <michal.kazior@tieto.com> wrote:
> There's a new firmware feature which uses a shared
> DMA memory so host can share it's per-sta per-tid
> queue size which is then subsequently used for
> firmware to assist in deciding which frames to put
> on the intermediate host-device tx queue.
>
> This patchset adds only basic support to make
> the firmware supporting the feature happy and
> running at all. Without it firmware would freeze
> shortly after booting.
>
> More patches will follow some time later to add
> the "new data path" logic.
>
>
> v2:
>  * fix gfp allocation [Ben]

Sorry for wrong email subjects. Apparently git send-email wasn't happy
with "--subject PATCHv2" as opposed to "--subject=PATCHv2" ..


Michał

_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k

Re: [PATCH 0/5] ath10k: add basic hostq support

[Michal Kazior]

On 21 January 2016 at 14:13, Michal Kazior <michal.kazior@tieto.com> wrote:
> There's a new firmware feature which uses a shared
> DMA memory so host can share it's per-sta per-tid
> queue size which is then subsequently used for
> firmware to assist in deciding which frames to put
> on the intermediate host-device tx queue.
>
> This patchset adds only basic support to make
> the firmware supporting the feature happy and
> running at all. Without it firmware would freeze
> shortly after booting.
>
> More patches will follow some time later to add
> the "new data path" logic.
>
>
> v2:
>  * fix gfp allocation [Ben]

Sorry for wrong email subjects. Apparently git send-email wasn't happy
with "--subject PATCHv2" as opposed to "--subject=PATCHv2" ..


Michał

Re: [PATCH 0/5] ath10k: add basic hostq support

[Kalle Valo]

Michal Kazior <michal.kazior@tieto.com> writes:

> There's a new firmware feature which uses a shared
> DMA memory so host can share it's per-sta per-tid
> queue size which is then subsequently used for
> firmware to assist in deciding which frames to put
> on the intermediate host-device tx queue.
>
> This patchset adds only basic support to make
> the firmware supporting the feature happy and
> running at all. Without it firmware would freeze
> shortly after booting.
>
> More patches will follow some time later to add
> the "new data path" logic.
>
>
> v2:
>  * fix gfp allocation [Ben]
>
>
> Michal Kazior (5):
>   ath10k: rename some HTT events
>   ath10k: add new htt definitions
>   ath10k: add new FW_FEATURE_PEER_FLOW_CONTROL
>   ath10k: clean up cont frag desc init code
>   ath10k: implement basic support for new tx path firmware

Applied, thanks.

-- 
Kalle Valo

_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k

Re: [PATCH 0/5] ath10k: add basic hostq support

[Kalle Valo]

Michal Kazior <michal.kazior@tieto.com> writes:

> There's a new firmware feature which uses a shared
> DMA memory so host can share it's per-sta per-tid
> queue size which is then subsequently used for
> firmware to assist in deciding which frames to put
> on the intermediate host-device tx queue.
>
> This patchset adds only basic support to make
> the firmware supporting the feature happy and
> running at all. Without it firmware would freeze
> shortly after booting.
>
> More patches will follow some time later to add
> the "new data path" logic.
>
>
> v2:
>  * fix gfp allocation [Ben]
>
>
> Michal Kazior (5):
>   ath10k: rename some HTT events
>   ath10k: add new htt definitions
>   ath10k: add new FW_FEATURE_PEER_FLOW_CONTROL
>   ath10k: clean up cont frag desc init code
>   ath10k: implement basic support for new tx path firmware

Applied, thanks.

-- 
Kalle Valo