[PATCH v2 1/5] clk: ep93xx: Implement clk_get_parent()

[PATCH v2 1/5] clk: ep93xx: Implement clk_get_parent()

[Alexander Sverdlin]

Trivial implementation of clk_get_parent(), but necessary for some drivers,
such as ADC.

Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
---
 arch/arm/mach-ep93xx/clock.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/arch/arm/mach-ep93xx/clock.c b/arch/arm/mach-ep93xx/clock.c
index 39ef3b6..b9cd9d7 100644
--- a/arch/arm/mach-ep93xx/clock.c
+++ b/arch/arm/mach-ep93xx/clock.c
@@ -475,6 +475,12 @@ int clk_set_rate(struct clk *clk, unsigned long rate)
 }
 EXPORT_SYMBOL(clk_set_rate);

+struct clk *clk_get_parent(struct clk *clk)
+{
+	return clk->parent;
+}
+EXPORT_SYMBOL(clk_get_parent);
+

 static char fclk_divisors[] = { 1, 2, 4, 8, 16, 1, 1, 1 };
 static char hclk_divisors[] = { 1, 2, 4, 5, 6, 8, 16, 32 };

[PATCH v2 1/5] clk: ep93xx: Implement clk_get_parent()

[Alexander Sverdlin]

Trivial implementation of clk_get_parent(), but necessary for some drivers,
such as ADC.

Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
---
 arch/arm/mach-ep93xx/clock.c | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/arch/arm/mach-ep93xx/clock.c b/arch/arm/mach-ep93xx/clock.c
index 39ef3b6..b9cd9d7 100644
--- a/arch/arm/mach-ep93xx/clock.c
+++ b/arch/arm/mach-ep93xx/clock.c
@@ -475,6 +475,12 @@ int clk_set_rate(struct clk *clk, unsigned long rate)
 }
 EXPORT_SYMBOL(clk_set_rate);

+struct clk *clk_get_parent(struct clk *clk)
+{
+	return clk->parent;
+}
+EXPORT_SYMBOL(clk_get_parent);
+

 static char fclk_divisors[] = { 1, 2, 4, 8, 16, 1, 1, 1 };
 static char hclk_divisors[] = { 1, 2, 4, 5, 6, 8, 16, 32 };

[PATCH v2 2/5] clk: ep93xx: Add ADC clock

[Alexander Sverdlin]

ADC and keypad controller clocks share the same control register, so use the
existing infrastructure to add ADC clock support for Cirrus Logic EP93xx SoCs.

Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
---
 arch/arm/mach-ep93xx/clock.c | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/arm/mach-ep93xx/clock.c b/arch/arm/mach-ep93xx/clock.c
index b9cd9d7..4253426 100644
--- a/arch/arm/mach-ep93xx/clock.c
+++ b/arch/arm/mach-ep93xx/clock.c
@@ -98,6 +98,13 @@ static struct clk clk_keypad = {
 	.enable_mask	= EP93XX_SYSCON_KEYTCHCLKDIV_KEN,
 	.set_rate	= set_keytchclk_rate,
 };
+static struct clk clk_adc = {
+	.parent		= &clk_xtali,
+	.sw_locked	= 1,
+	.enable_reg	= EP93XX_SYSCON_KEYTCHCLKDIV,
+	.enable_mask	= EP93XX_SYSCON_KEYTCHCLKDIV_TSEN,
+	.set_rate	= set_keytchclk_rate,
+};
 static struct clk clk_spi = {
 	.parent		= &clk_xtali,
 	.rate		= EP93XX_EXT_CLK_RATE,
@@ -214,6 +221,7 @@ static struct clk_lookup clocks[] = {
 	INIT_CK(NULL,			"pll2",		&clk_pll2),
 	INIT_CK("ohci-platform",	NULL,		&clk_usb_host),
 	INIT_CK("ep93xx-keypad",	NULL,		&clk_keypad),
+	INIT_CK("ep93xx-adc",		NULL,		&clk_adc),
 	INIT_CK("ep93xx-fb",		NULL,		&clk_video),
 	INIT_CK("ep93xx-spi.0",		NULL,		&clk_spi),
 	INIT_CK("ep93xx-i2s",		"mclk",		&clk_i2s_mclk),

[PATCH v2 2/5] clk: ep93xx: Add ADC clock

[Alexander Sverdlin]

ADC and keypad controller clocks share the same control register, so use the
existing infrastructure to add ADC clock support for Cirrus Logic EP93xx SoCs.

Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
---
 arch/arm/mach-ep93xx/clock.c | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/arm/mach-ep93xx/clock.c b/arch/arm/mach-ep93xx/clock.c
index b9cd9d7..4253426 100644
--- a/arch/arm/mach-ep93xx/clock.c
+++ b/arch/arm/mach-ep93xx/clock.c
@@ -98,6 +98,13 @@ static struct clk clk_keypad = {
 	.enable_mask	= EP93XX_SYSCON_KEYTCHCLKDIV_KEN,
 	.set_rate	= set_keytchclk_rate,
 };
+static struct clk clk_adc = {
+	.parent		= &clk_xtali,
+	.sw_locked	= 1,
+	.enable_reg	= EP93XX_SYSCON_KEYTCHCLKDIV,
+	.enable_mask	= EP93XX_SYSCON_KEYTCHCLKDIV_TSEN,
+	.set_rate	= set_keytchclk_rate,
+};
 static struct clk clk_spi = {
 	.parent		= &clk_xtali,
 	.rate		= EP93XX_EXT_CLK_RATE,
@@ -214,6 +221,7 @@ static struct clk_lookup clocks[] = {
 	INIT_CK(NULL,			"pll2",		&clk_pll2),
 	INIT_CK("ohci-platform",	NULL,		&clk_usb_host),
 	INIT_CK("ep93xx-keypad",	NULL,		&clk_keypad),
+	INIT_CK("ep93xx-adc",		NULL,		&clk_adc),
 	INIT_CK("ep93xx-fb",		NULL,		&clk_video),
 	INIT_CK("ep93xx-spi.0",		NULL,		&clk_spi),
 	INIT_CK("ep93xx-i2s",		"mclk",		&clk_i2s_mclk),

[PATCH v2 3/5] ep93xx: Add ADC platform device support to core

[Alexander Sverdlin]

Newly provided ep93xx_register_adc() could be used by machine-specific code
to create ADC platform device on Cirrus Logic EP93xx SoC-based machines.

Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
---
 arch/arm/mach-ep93xx/core.c                  | 24 ++++++++++++++++++++++++
 arch/arm/mach-ep93xx/include/mach/platform.h |  1 +
 arch/arm/mach-ep93xx/soc.h                   |  1 +
 3 files changed, 26 insertions(+)

diff --git a/arch/arm/mach-ep93xx/core.c b/arch/arm/mach-ep93xx/core.c
index c393b1b..f53c618 100644
--- a/arch/arm/mach-ep93xx/core.c
+++ b/arch/arm/mach-ep93xx/core.c
@@ -821,6 +821,30 @@ void ep93xx_ide_release_gpio(struct platform_device *pdev)
 EXPORT_SYMBOL(ep93xx_ide_release_gpio);

 /*************************************************************************
+ * EP93xx ADC
+ *************************************************************************/
+static struct resource ep93xx_adc_resources[] = {
+	DEFINE_RES_MEM(EP93XX_ADC_PHYS_BASE, 0x28),
+	DEFINE_RES_IRQ(IRQ_EP93XX_TOUCH),
+};
+
+static struct platform_device ep93xx_adc_device = {
+	.name		= "ep93xx-adc",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(ep93xx_adc_resources),
+	.resource	= ep93xx_adc_resources,
+};
+
+void __init ep93xx_register_adc(void)
+{
+	/* Power up ADC, deactivate Touch Screen Controller */
+	ep93xx_devcfg_set_clear(EP93XX_SYSCON_DEVCFG_TIN,
+				EP93XX_SYSCON_DEVCFG_ADCPD);
+
+	platform_device_register(&ep93xx_adc_device);
+}
+
+/*************************************************************************
  * EP93xx Security peripheral
  *************************************************************************/

diff --git a/arch/arm/mach-ep93xx/include/mach/platform.h b/arch/arm/mach-ep93xx/include/mach/platform.h
index 4c0bbd9..db08396 100644
--- a/arch/arm/mach-ep93xx/include/mach/platform.h
+++ b/arch/arm/mach-ep93xx/include/mach/platform.h
@@ -52,6 +52,7 @@ int ep93xx_i2s_acquire(void);
 void ep93xx_i2s_release(void);
 void ep93xx_register_ac97(void);
 void ep93xx_register_ide(void);
+void ep93xx_register_adc(void);
 int ep93xx_ide_acquire_gpio(struct platform_device *pdev);
 void ep93xx_ide_release_gpio(struct platform_device *pdev);

diff --git a/arch/arm/mach-ep93xx/soc.h b/arch/arm/mach-ep93xx/soc.h
index 7bf7ff8..d20e631 100644
--- a/arch/arm/mach-ep93xx/soc.h
+++ b/arch/arm/mach-ep93xx/soc.h
@@ -95,6 +95,7 @@
 #define EP93XX_KEY_MATRIX_PHYS_BASE	EP93XX_APB_PHYS(0x000f0000)
 #define EP93XX_KEY_MATRIX_BASE		EP93XX_APB_IOMEM(0x000f0000)

+#define EP93XX_ADC_PHYS_BASE		EP93XX_APB_PHYS(0x00100000)
 #define EP93XX_ADC_BASE			EP93XX_APB_IOMEM(0x00100000)
 #define EP93XX_TOUCHSCREEN_BASE		EP93XX_APB_IOMEM(0x00100000)

[PATCH v2 3/5] ep93xx: Add ADC platform device support to core

[Alexander Sverdlin]

Newly provided ep93xx_register_adc() could be used by machine-specific code
to create ADC platform device on Cirrus Logic EP93xx SoC-based machines.

Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
---
 arch/arm/mach-ep93xx/core.c                  | 24 ++++++++++++++++++++++++
 arch/arm/mach-ep93xx/include/mach/platform.h |  1 +
 arch/arm/mach-ep93xx/soc.h                   |  1 +
 3 files changed, 26 insertions(+)

diff --git a/arch/arm/mach-ep93xx/core.c b/arch/arm/mach-ep93xx/core.c
index c393b1b..f53c618 100644
--- a/arch/arm/mach-ep93xx/core.c
+++ b/arch/arm/mach-ep93xx/core.c
@@ -821,6 +821,30 @@ void ep93xx_ide_release_gpio(struct platform_device *pdev)
 EXPORT_SYMBOL(ep93xx_ide_release_gpio);

 /*************************************************************************
+ * EP93xx ADC
+ *************************************************************************/
+static struct resource ep93xx_adc_resources[] = {
+	DEFINE_RES_MEM(EP93XX_ADC_PHYS_BASE, 0x28),
+	DEFINE_RES_IRQ(IRQ_EP93XX_TOUCH),
+};
+
+static struct platform_device ep93xx_adc_device = {
+	.name		= "ep93xx-adc",
+	.id		= -1,
+	.num_resources	= ARRAY_SIZE(ep93xx_adc_resources),
+	.resource	= ep93xx_adc_resources,
+};
+
+void __init ep93xx_register_adc(void)
+{
+	/* Power up ADC, deactivate Touch Screen Controller */
+	ep93xx_devcfg_set_clear(EP93XX_SYSCON_DEVCFG_TIN,
+				EP93XX_SYSCON_DEVCFG_ADCPD);
+
+	platform_device_register(&ep93xx_adc_device);
+}
+
+/*************************************************************************
  * EP93xx Security peripheral
  *************************************************************************/

diff --git a/arch/arm/mach-ep93xx/include/mach/platform.h b/arch/arm/mach-ep93xx/include/mach/platform.h
index 4c0bbd9..db08396 100644
--- a/arch/arm/mach-ep93xx/include/mach/platform.h
+++ b/arch/arm/mach-ep93xx/include/mach/platform.h
@@ -52,6 +52,7 @@ int ep93xx_i2s_acquire(void);
 void ep93xx_i2s_release(void);
 void ep93xx_register_ac97(void);
 void ep93xx_register_ide(void);
+void ep93xx_register_adc(void);
 int ep93xx_ide_acquire_gpio(struct platform_device *pdev);
 void ep93xx_ide_release_gpio(struct platform_device *pdev);

diff --git a/arch/arm/mach-ep93xx/soc.h b/arch/arm/mach-ep93xx/soc.h
index 7bf7ff8..d20e631 100644
--- a/arch/arm/mach-ep93xx/soc.h
+++ b/arch/arm/mach-ep93xx/soc.h
@@ -95,6 +95,7 @@
 #define EP93XX_KEY_MATRIX_PHYS_BASE	EP93XX_APB_PHYS(0x000f0000)
 #define EP93XX_KEY_MATRIX_BASE		EP93XX_APB_IOMEM(0x000f0000)

+#define EP93XX_ADC_PHYS_BASE		EP93XX_APB_PHYS(0x00100000)
 #define EP93XX_ADC_BASE			EP93XX_APB_IOMEM(0x00100000)
 #define EP93XX_TOUCHSCREEN_BASE		EP93XX_APB_IOMEM(0x00100000)

[PATCH v2 4/5] edb93xx: Add ADC platform device

[Alexander Sverdlin]

This enables the creation of ADC platform device on EDB93xx series of Cirrus
Logic evaluation boards. The driver for this device must be enabled separately,
either as built-in, or a module.

Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
---
 arch/arm/mach-ep93xx/edb93xx.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/mach-ep93xx/edb93xx.c b/arch/arm/mach-ep93xx/edb93xx.c
index ad92d9f..8da0127 100644
--- a/arch/arm/mach-ep93xx/edb93xx.c
+++ b/arch/arm/mach-ep93xx/edb93xx.c
@@ -264,6 +264,7 @@ static void __init edb93xx_init_machine(void)
 	edb93xx_register_pwm();
 	edb93xx_register_fb();
 	edb93xx_register_ide();
+	ep93xx_register_adc();
 }

[PATCH v2 4/5] edb93xx: Add ADC platform device

[Alexander Sverdlin]

This enables the creation of ADC platform device on EDB93xx series of Cirrus
Logic evaluation boards. The driver for this device must be enabled separately,
either as built-in, or a module.

Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
---
 arch/arm/mach-ep93xx/edb93xx.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/mach-ep93xx/edb93xx.c b/arch/arm/mach-ep93xx/edb93xx.c
index ad92d9f..8da0127 100644
--- a/arch/arm/mach-ep93xx/edb93xx.c
+++ b/arch/arm/mach-ep93xx/edb93xx.c
@@ -264,6 +264,7 @@ static void __init edb93xx_init_machine(void)
 	edb93xx_register_pwm();
 	edb93xx_register_fb();
 	edb93xx_register_ide();
+	ep93xx_register_adc();
 }

[PATCH v2 5/5] iio: adc: New driver for Cirrus Logic EP93xx ADC

[Alexander Sverdlin]

New driver adding support for ADC found on Cirrus Logic EP93xx series of SoCs.
Board specific code must take care to create plaform device with all necessary
resources.

Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
---
 Documentation/iio/ep93xx_adc.txt |  29 +++++
 drivers/iio/adc/Kconfig          |  11 ++
 drivers/iio/adc/Makefile         |   1 +
 drivers/iio/adc/ep93xx_adc.c     | 261 +++++++++++++++++++++++++++++++++++++++
 4 files changed, 302 insertions(+)
 create mode 100644 Documentation/iio/ep93xx_adc.txt
 create mode 100644 drivers/iio/adc/ep93xx_adc.c

diff --git a/Documentation/iio/ep93xx_adc.txt b/Documentation/iio/ep93xx_adc.txt
new file mode 100644
index 0000000..321e59f
--- /dev/null
+++ b/Documentation/iio/ep93xx_adc.txt
@@ -0,0 +1,29 @@
+Cirrus Logic EP93xx ADC driver.
+
+1. Overview
+
+The driver is intended to work on both low-end (EP9301, EP9302) devices with
+5-channel ADC and high-end (EP9307, EP9312, EP9315) devices with 10-channel
+touchscreen/ADC module.
+
+2. Channel numbering
+
+Numbering scheme for channels 0..4 is defined in EP9301 and EP9302 datasheets.
+EP9307, EP9312 and EP9312 have 3 channels more (total 8), but the numbering is
+not defined. So the last three are numbered randomly, let's say.
+
+Assuming ep93xx_adc is IIO device0, you'd find following entries under
+/sys/bus/iio/devices/iio:device0/:
+
+  +-----------------+---------------+
+  | sysfs entry     | ball/pin name |
+  +-----------------+---------------+
+  | in_voltage0_raw | YM            |
+  | in_voltage1_raw | SXP           |
+  | in_voltage2_raw | SXM           |
+  | in_voltage3_raw | SYP           |
+  | in_voltage4_raw | SYM           |
+  | in_voltage5_raw | XP            |
+  | in_voltage6_raw | XM            |
+  | in_voltage7_raw | YP            |
+  +-----------------+---------------+
diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
index 283ded7..0482f29 100644
--- a/drivers/iio/adc/Kconfig
+++ b/drivers/iio/adc/Kconfig
@@ -172,6 +172,17 @@ config DA9150_GPADC
 	  To compile this driver as a module, choose M here: the module will be
 	  called berlin2-adc.

+config EP93XX_ADC
+	tristate "Cirrus Logic EP93XX ADC driver"
+	depends on ARCH_EP93XX
+	help
+	  Driver for the ADC module on the EP93XX series of SoC from Cirrus Logic.
+	  It's recommended to switch on CONFIG_HIGH_RES_TIMERS option, in this
+	  case driver will reduce its CPU usage by 90% in some use cases.
+
+	  To compile this driver as a module, choose M here: the module will be
+	  called ep93xx_adc.
+
 config EXYNOS_ADC
 	tristate "Exynos ADC driver support"
 	depends on ARCH_EXYNOS || ARCH_S3C24XX || ARCH_S3C64XX || (OF && COMPILE_TEST)
diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
index 6435780..cd7d33e 100644
--- a/drivers/iio/adc/Makefile
+++ b/drivers/iio/adc/Makefile
@@ -18,6 +18,7 @@ obj-$(CONFIG_AXP288_ADC) += axp288_adc.o
 obj-$(CONFIG_BERLIN2_ADC) += berlin2-adc.o
 obj-$(CONFIG_CC10001_ADC) += cc10001_adc.o
 obj-$(CONFIG_DA9150_GPADC) += da9150-gpadc.o
+obj-$(CONFIG_EP93XX_ADC) += ep93xx_adc.o
 obj-$(CONFIG_EXYNOS_ADC) += exynos_adc.o
 obj-$(CONFIG_HI8435) += hi8435.o
 obj-$(CONFIG_IMX7D_ADC) += imx7d_adc.o
diff --git a/drivers/iio/adc/ep93xx_adc.c b/drivers/iio/adc/ep93xx_adc.c
new file mode 100644
index 0000000..3728591
--- /dev/null
+++ b/drivers/iio/adc/ep93xx_adc.c
@@ -0,0 +1,261 @@
+/*
+ * Driver for ADC module on the Cirrus Logic EP93xx series of SoCs
+ *
+ * Copyright (C) 2015 Alexander Sverdlin
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * The driver uses polling to get the conversion status. According to EP93xx
+ * datasheets, reading ADCResult register starts the conversion, but user is also
+ * responsible for ensuring that delay between adjacent conversion triggers is
+ * long enough so that maximum allowed conversion rate is not exceeded. This
+ * basically renders IRQ mode unusable.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/iio/iio.h>
+#include <linux/io.h>
+#include <linux/irqflags.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/platform_device.h>
+
+#define EP93XX_NUM_CHANNELS 8
+
+/*
+ * This code could benefit from real HR Timers, but jiffy granularity would
+ * lower ADC conversion rate down to CONFIG_HZ, so we fallback to busy wait
+ * in such case.
+ *
+ * HR Timers-based version loads CPU only up to 10% during back to back ADC
+ * conversion, while busy wait-based version consumes whole CPU power.
+ */
+#ifdef CONFIG_HIGH_RES_TIMERS
+#define ep93xx_adc_delay(usmin, usmax) usleep_range(usmin, usmax)
+#else
+#define ep93xx_adc_delay(usmin, usmax) udelay(usmin)
+#endif
+
+#define EP93XX_ADC_RESULT	0x08
+#define   EP93XX_ADC_SDR	BIT(31)
+#define EP93XX_ADC_SWITCH	0x18
+#define EP93XX_ADC_SW_LOCK	0x20
+#define EP93XX_ADC_INT_EN	0x24
+#define   EP93XX_ADC_RINTEN	BIT(11)
+
+struct ep93xx_adc_priv {
+	struct clk *clk;
+	void __iomem *base;
+	int lastch;
+	struct mutex lock;
+};
+
+#define EP93XX_ADC_CH(index, dname, swcfg) {			\
+	.type = IIO_VOLTAGE,					\
+	.indexed = 1,						\
+	.channel = index,					\
+	.address = swcfg,					\
+	.datasheet_name = dname,				\
+	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),		\
+	.info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SCALE) |	\
+				   BIT(IIO_CHAN_INFO_OFFSET),	\
+}
+
+/*
+ * Numbering scheme for channels 0..4 is defined in EP9301 and EP9302 datasheets.
+ * EP9307, EP9312 and EP9312 have 3 channels more (total 8), but the numbering is
+ * not defined. So the last three are numbered randomly, let's say.
+ */
+static const struct iio_chan_spec ep93xx_adc_channels[EP93XX_NUM_CHANNELS] = {
+	EP93XX_ADC_CH(0, "YM",	0x608),
+	EP93XX_ADC_CH(1, "SXP",	0x680),
+	EP93XX_ADC_CH(2, "SXM",	0x640),
+	EP93XX_ADC_CH(3, "SYP",	0x620),
+	EP93XX_ADC_CH(4, "SYM",	0x610),
+	EP93XX_ADC_CH(5, "XP",	0x601),
+	EP93XX_ADC_CH(6, "XM",	0x602),
+	EP93XX_ADC_CH(7, "YP",	0x604),
+};
+
+static int ep93xx_read_raw(struct iio_dev *iiodev,
+			   struct iio_chan_spec const *channel, int *value,
+			   int *shift, long mask)
+{
+	struct ep93xx_adc_priv *priv = iio_priv(iiodev);
+	unsigned long timeout;
+	int ret;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_RAW:
+		mutex_lock(&priv->lock);
+		if (priv->lastch != channel->channel) {
+			priv->lastch = channel->channel;
+			/*
+			 * Switch register is software-locked, unlocking must be
+			 * immediately followed by write
+			 */
+			local_irq_disable();
+			writel_relaxed(0xAA, priv->base + EP93XX_ADC_SW_LOCK);
+			writel_relaxed(channel->address,
+				       priv->base + EP93XX_ADC_SWITCH);
+			local_irq_enable();
+			/*
+			 * Settling delay depends on module clock and could be
+			 * 2ms or 500us
+			 */
+			ep93xx_adc_delay(2000, 2000);
+		}
+		/* Start the conversion, eventually discarding old result */
+		readl_relaxed(priv->base + EP93XX_ADC_RESULT);
+		/* Ensure maximun conversion rate is not exceeded */
+		ep93xx_adc_delay(DIV_ROUND_UP(1000000, 925),
+				 DIV_ROUND_UP(1000000, 925));
+		/* At this point conversion must be completed, but anyway... */
+		ret = IIO_VAL_INT;
+		timeout = jiffies + msecs_to_jiffies(1) + 1;
+		while (1) {
+			u32 t;
+
+			t = readl_relaxed(priv->base + EP93XX_ADC_RESULT);
+			if (t & EP93XX_ADC_SDR) {
+				/* Sign extend lower 16 bits */
+				*value = (s16)t;
+				break;
+			}
+
+			if (time_after(jiffies, timeout)) {
+				dev_err(&iiodev->dev, "Conversion timeout\n");
+				ret = -ETIMEDOUT;
+				break;
+			}
+
+			cpu_relax();
+		}
+		mutex_unlock(&priv->lock);
+		return ret;
+
+	case IIO_CHAN_INFO_OFFSET:
+		/* According to datasheet, range is -25000..25000 */
+		*value = 25000;
+		return IIO_VAL_INT;
+
+	case IIO_CHAN_INFO_SCALE:
+		/* Typical supply voltage is 3.3v */
+		*value = (1ULL << 32) * 3300 / 50000;
+		*shift = 32;
+		return IIO_VAL_FRACTIONAL_LOG2;
+	}
+
+	return -EINVAL;
+}
+
+static const struct iio_info ep93xx_adc_info = {
+	.driver_module = THIS_MODULE,
+	.read_raw = ep93xx_read_raw,
+};
+
+static int ep93xx_adc_probe(struct platform_device *pdev)
+{
+	int ret;
+	struct iio_dev *iiodev;
+	struct ep93xx_adc_priv *priv;
+	struct clk *pclk;
+	struct resource *res;
+
+	iiodev = devm_iio_device_alloc(&pdev->dev,
+				       sizeof(struct ep93xx_adc_priv));
+	if (!iiodev)
+		return -ENOMEM;
+	priv = iio_priv(iiodev);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(&pdev->dev, "Cannot obtain memory resource\n");
+		return -ENXIO;
+	}
+	priv->base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(priv->base)) {
+		dev_err(&pdev->dev, "Cannot map memory resource\n");
+		return PTR_ERR(priv->base);
+	}
+
+	iiodev->dev.parent = &pdev->dev;
+	iiodev->name = dev_name(&pdev->dev);
+	iiodev->modes = INDIO_DIRECT_MODE;
+	iiodev->info = &ep93xx_adc_info;
+	iiodev->num_channels = ARRAY_SIZE(ep93xx_adc_channels);
+	iiodev->channels = ep93xx_adc_channels;
+
+	priv->lastch = -1;
+	mutex_init(&priv->lock);
+
+	platform_set_drvdata(pdev, iiodev);
+
+	priv->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(priv->clk)) {
+		dev_err(&pdev->dev, "Cannot obtain clock\n");
+		return PTR_ERR(priv->clk);
+	}
+
+	pclk = clk_get_parent(priv->clk);
+	if (!pclk) {
+		dev_warn(&pdev->dev, "Cannot obtain parent clock\n");
+	} else {
+		/*
+		 * This is actually a place for improvement:
+		 * EP93xx ADC supports two clock divisors -- 4 and 16,
+		 * resulting in conversion rates 3750 and 925 samples per second
+		 * respectively with 500uS or 2ms settling time respectively.
+		 * One might find this interesting enough to be configurable.
+		 */
+		ret = clk_set_rate(priv->clk, clk_get_rate(pclk) / 16);
+		if (ret)
+			dev_warn(&pdev->dev, "Cannot set clock rate\n");
+		/*
+		 * We can tolerate rate setting failure because the module should
+		 * work in any case.
+		 */
+	}
+
+	ret = clk_enable(priv->clk);
+	if (ret) {
+		dev_err(&pdev->dev, "Cannot enable clock\n");
+		return ret;
+	}
+
+	ret = iio_device_register(iiodev);
+	if (ret)
+		clk_disable(priv->clk);
+
+	return ret;
+}
+
+static int ep93xx_adc_remove(struct platform_device *pdev)
+{
+	struct iio_dev *iiodev = platform_get_drvdata(pdev);
+	struct ep93xx_adc_priv *priv = iio_priv(iiodev);
+
+	iio_device_unregister(iiodev);
+	clk_disable(priv->clk);
+
+	return 0;
+}
+
+static struct platform_driver ep93xx_adc_driver = {
+	.driver = {
+		.name = "ep93xx-adc",
+	},
+	.probe = ep93xx_adc_probe,
+	.remove = ep93xx_adc_remove,
+};
+module_platform_driver(ep93xx_adc_driver);
+
+MODULE_AUTHOR("Alexander Sverdlin <alexander.sverdlin@gmail.com>");
+MODULE_DESCRIPTION("Cirrus Logic EP93XX ADC driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:ep93xx-adc");

[PATCH v2 5/5] iio: adc: New driver for Cirrus Logic EP93xx ADC

[Alexander Sverdlin]

New driver adding support for ADC found on Cirrus Logic EP93xx series of SoCs.
Board specific code must take care to create plaform device with all necessary
resources.

Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
---
 Documentation/iio/ep93xx_adc.txt |  29 +++++
 drivers/iio/adc/Kconfig          |  11 ++
 drivers/iio/adc/Makefile         |   1 +
 drivers/iio/adc/ep93xx_adc.c     | 261 +++++++++++++++++++++++++++++++++++++++
 4 files changed, 302 insertions(+)
 create mode 100644 Documentation/iio/ep93xx_adc.txt
 create mode 100644 drivers/iio/adc/ep93xx_adc.c

diff --git a/Documentation/iio/ep93xx_adc.txt b/Documentation/iio/ep93xx_adc.txt
new file mode 100644
index 0000000..321e59f
--- /dev/null
+++ b/Documentation/iio/ep93xx_adc.txt
@@ -0,0 +1,29 @@
+Cirrus Logic EP93xx ADC driver.
+
+1. Overview
+
+The driver is intended to work on both low-end (EP9301, EP9302) devices with
+5-channel ADC and high-end (EP9307, EP9312, EP9315) devices with 10-channel
+touchscreen/ADC module.
+
+2. Channel numbering
+
+Numbering scheme for channels 0..4 is defined in EP9301 and EP9302 datasheets.
+EP9307, EP9312 and EP9312 have 3 channels more (total 8), but the numbering is
+not defined. So the last three are numbered randomly, let's say.
+
+Assuming ep93xx_adc is IIO device0, you'd find following entries under
+/sys/bus/iio/devices/iio:device0/:
+
+  +-----------------+---------------+
+  | sysfs entry     | ball/pin name |
+  +-----------------+---------------+
+  | in_voltage0_raw | YM            |
+  | in_voltage1_raw | SXP           |
+  | in_voltage2_raw | SXM           |
+  | in_voltage3_raw | SYP           |
+  | in_voltage4_raw | SYM           |
+  | in_voltage5_raw | XP            |
+  | in_voltage6_raw | XM            |
+  | in_voltage7_raw | YP            |
+  +-----------------+---------------+
diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
index 283ded7..0482f29 100644
--- a/drivers/iio/adc/Kconfig
+++ b/drivers/iio/adc/Kconfig
@@ -172,6 +172,17 @@ config DA9150_GPADC
 	  To compile this driver as a module, choose M here: the module will be
 	  called berlin2-adc.

+config EP93XX_ADC
+	tristate "Cirrus Logic EP93XX ADC driver"
+	depends on ARCH_EP93XX
+	help
+	  Driver for the ADC module on the EP93XX series of SoC from Cirrus Logic.
+	  It's recommended to switch on CONFIG_HIGH_RES_TIMERS option, in this
+	  case driver will reduce its CPU usage by 90% in some use cases.
+
+	  To compile this driver as a module, choose M here: the module will be
+	  called ep93xx_adc.
+
 config EXYNOS_ADC
 	tristate "Exynos ADC driver support"
 	depends on ARCH_EXYNOS || ARCH_S3C24XX || ARCH_S3C64XX || (OF && COMPILE_TEST)
diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
index 6435780..cd7d33e 100644
--- a/drivers/iio/adc/Makefile
+++ b/drivers/iio/adc/Makefile
@@ -18,6 +18,7 @@ obj-$(CONFIG_AXP288_ADC) += axp288_adc.o
 obj-$(CONFIG_BERLIN2_ADC) += berlin2-adc.o
 obj-$(CONFIG_CC10001_ADC) += cc10001_adc.o
 obj-$(CONFIG_DA9150_GPADC) += da9150-gpadc.o
+obj-$(CONFIG_EP93XX_ADC) += ep93xx_adc.o
 obj-$(CONFIG_EXYNOS_ADC) += exynos_adc.o
 obj-$(CONFIG_HI8435) += hi8435.o
 obj-$(CONFIG_IMX7D_ADC) += imx7d_adc.o
diff --git a/drivers/iio/adc/ep93xx_adc.c b/drivers/iio/adc/ep93xx_adc.c
new file mode 100644
index 0000000..3728591
--- /dev/null
+++ b/drivers/iio/adc/ep93xx_adc.c
@@ -0,0 +1,261 @@
+/*
+ * Driver for ADC module on the Cirrus Logic EP93xx series of SoCs
+ *
+ * Copyright (C) 2015 Alexander Sverdlin
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * The driver uses polling to get the conversion status. According to EP93xx
+ * datasheets, reading ADCResult register starts the conversion, but user is also
+ * responsible for ensuring that delay between adjacent conversion triggers is
+ * long enough so that maximum allowed conversion rate is not exceeded. This
+ * basically renders IRQ mode unusable.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/iio/iio.h>
+#include <linux/io.h>
+#include <linux/irqflags.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/platform_device.h>
+
+#define EP93XX_NUM_CHANNELS 8
+
+/*
+ * This code could benefit from real HR Timers, but jiffy granularity would
+ * lower ADC conversion rate down to CONFIG_HZ, so we fallback to busy wait
+ * in such case.
+ *
+ * HR Timers-based version loads CPU only up to 10% during back to back ADC
+ * conversion, while busy wait-based version consumes whole CPU power.
+ */
+#ifdef CONFIG_HIGH_RES_TIMERS
+#define ep93xx_adc_delay(usmin, usmax) usleep_range(usmin, usmax)
+#else
+#define ep93xx_adc_delay(usmin, usmax) udelay(usmin)
+#endif
+
+#define EP93XX_ADC_RESULT	0x08
+#define   EP93XX_ADC_SDR	BIT(31)
+#define EP93XX_ADC_SWITCH	0x18
+#define EP93XX_ADC_SW_LOCK	0x20
+#define EP93XX_ADC_INT_EN	0x24
+#define   EP93XX_ADC_RINTEN	BIT(11)
+
+struct ep93xx_adc_priv {
+	struct clk *clk;
+	void __iomem *base;
+	int lastch;
+	struct mutex lock;
+};
+
+#define EP93XX_ADC_CH(index, dname, swcfg) {			\
+	.type = IIO_VOLTAGE,					\
+	.indexed = 1,						\
+	.channel = index,					\
+	.address = swcfg,					\
+	.datasheet_name = dname,				\
+	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),		\
+	.info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SCALE) |	\
+				   BIT(IIO_CHAN_INFO_OFFSET),	\
+}
+
+/*
+ * Numbering scheme for channels 0..4 is defined in EP9301 and EP9302 datasheets.
+ * EP9307, EP9312 and EP9312 have 3 channels more (total 8), but the numbering is
+ * not defined. So the last three are numbered randomly, let's say.
+ */
+static const struct iio_chan_spec ep93xx_adc_channels[EP93XX_NUM_CHANNELS] = {
+	EP93XX_ADC_CH(0, "YM",	0x608),
+	EP93XX_ADC_CH(1, "SXP",	0x680),
+	EP93XX_ADC_CH(2, "SXM",	0x640),
+	EP93XX_ADC_CH(3, "SYP",	0x620),
+	EP93XX_ADC_CH(4, "SYM",	0x610),
+	EP93XX_ADC_CH(5, "XP",	0x601),
+	EP93XX_ADC_CH(6, "XM",	0x602),
+	EP93XX_ADC_CH(7, "YP",	0x604),
+};
+
+static int ep93xx_read_raw(struct iio_dev *iiodev,
+			   struct iio_chan_spec const *channel, int *value,
+			   int *shift, long mask)
+{
+	struct ep93xx_adc_priv *priv = iio_priv(iiodev);
+	unsigned long timeout;
+	int ret;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_RAW:
+		mutex_lock(&priv->lock);
+		if (priv->lastch != channel->channel) {
+			priv->lastch = channel->channel;
+			/*
+			 * Switch register is software-locked, unlocking must be
+			 * immediately followed by write
+			 */
+			local_irq_disable();
+			writel_relaxed(0xAA, priv->base + EP93XX_ADC_SW_LOCK);
+			writel_relaxed(channel->address,
+				       priv->base + EP93XX_ADC_SWITCH);
+			local_irq_enable();
+			/*
+			 * Settling delay depends on module clock and could be
+			 * 2ms or 500us
+			 */
+			ep93xx_adc_delay(2000, 2000);
+		}
+		/* Start the conversion, eventually discarding old result */
+		readl_relaxed(priv->base + EP93XX_ADC_RESULT);
+		/* Ensure maximun conversion rate is not exceeded */
+		ep93xx_adc_delay(DIV_ROUND_UP(1000000, 925),
+				 DIV_ROUND_UP(1000000, 925));
+		/* At this point conversion must be completed, but anyway... */
+		ret = IIO_VAL_INT;
+		timeout = jiffies + msecs_to_jiffies(1) + 1;
+		while (1) {
+			u32 t;
+
+			t = readl_relaxed(priv->base + EP93XX_ADC_RESULT);
+			if (t & EP93XX_ADC_SDR) {
+				/* Sign extend lower 16 bits */
+				*value = (s16)t;
+				break;
+			}
+
+			if (time_after(jiffies, timeout)) {
+				dev_err(&iiodev->dev, "Conversion timeout\n");
+				ret = -ETIMEDOUT;
+				break;
+			}
+
+			cpu_relax();
+		}
+		mutex_unlock(&priv->lock);
+		return ret;
+
+	case IIO_CHAN_INFO_OFFSET:
+		/* According to datasheet, range is -25000..25000 */
+		*value = 25000;
+		return IIO_VAL_INT;
+
+	case IIO_CHAN_INFO_SCALE:
+		/* Typical supply voltage is 3.3v */
+		*value = (1ULL << 32) * 3300 / 50000;
+		*shift = 32;
+		return IIO_VAL_FRACTIONAL_LOG2;
+	}
+
+	return -EINVAL;
+}
+
+static const struct iio_info ep93xx_adc_info = {
+	.driver_module = THIS_MODULE,
+	.read_raw = ep93xx_read_raw,
+};
+
+static int ep93xx_adc_probe(struct platform_device *pdev)
+{
+	int ret;
+	struct iio_dev *iiodev;
+	struct ep93xx_adc_priv *priv;
+	struct clk *pclk;
+	struct resource *res;
+
+	iiodev = devm_iio_device_alloc(&pdev->dev,
+				       sizeof(struct ep93xx_adc_priv));
+	if (!iiodev)
+		return -ENOMEM;
+	priv = iio_priv(iiodev);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(&pdev->dev, "Cannot obtain memory resource\n");
+		return -ENXIO;
+	}
+	priv->base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(priv->base)) {
+		dev_err(&pdev->dev, "Cannot map memory resource\n");
+		return PTR_ERR(priv->base);
+	}
+
+	iiodev->dev.parent = &pdev->dev;
+	iiodev->name = dev_name(&pdev->dev);
+	iiodev->modes = INDIO_DIRECT_MODE;
+	iiodev->info = &ep93xx_adc_info;
+	iiodev->num_channels = ARRAY_SIZE(ep93xx_adc_channels);
+	iiodev->channels = ep93xx_adc_channels;
+
+	priv->lastch = -1;
+	mutex_init(&priv->lock);
+
+	platform_set_drvdata(pdev, iiodev);
+
+	priv->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(priv->clk)) {
+		dev_err(&pdev->dev, "Cannot obtain clock\n");
+		return PTR_ERR(priv->clk);
+	}
+
+	pclk = clk_get_parent(priv->clk);
+	if (!pclk) {
+		dev_warn(&pdev->dev, "Cannot obtain parent clock\n");
+	} else {
+		/*
+		 * This is actually a place for improvement:
+		 * EP93xx ADC supports two clock divisors -- 4 and 16,
+		 * resulting in conversion rates 3750 and 925 samples per second
+		 * respectively with 500uS or 2ms settling time respectively.
+		 * One might find this interesting enough to be configurable.
+		 */
+		ret = clk_set_rate(priv->clk, clk_get_rate(pclk) / 16);
+		if (ret)
+			dev_warn(&pdev->dev, "Cannot set clock rate\n");
+		/*
+		 * We can tolerate rate setting failure because the module should
+		 * work in any case.
+		 */
+	}
+
+	ret = clk_enable(priv->clk);
+	if (ret) {
+		dev_err(&pdev->dev, "Cannot enable clock\n");
+		return ret;
+	}
+
+	ret = iio_device_register(iiodev);
+	if (ret)
+		clk_disable(priv->clk);
+
+	return ret;
+}
+
+static int ep93xx_adc_remove(struct platform_device *pdev)
+{
+	struct iio_dev *iiodev = platform_get_drvdata(pdev);
+	struct ep93xx_adc_priv *priv = iio_priv(iiodev);
+
+	iio_device_unregister(iiodev);
+	clk_disable(priv->clk);
+
+	return 0;
+}
+
+static struct platform_driver ep93xx_adc_driver = {
+	.driver = {
+		.name = "ep93xx-adc",
+	},
+	.probe = ep93xx_adc_probe,
+	.remove = ep93xx_adc_remove,
+};
+module_platform_driver(ep93xx_adc_driver);
+
+MODULE_AUTHOR("Alexander Sverdlin <alexander.sverdlin@gmail.com>");
+MODULE_DESCRIPTION("Cirrus Logic EP93XX ADC driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:ep93xx-adc");

Re: [PATCH v2 5/5] iio: adc: New driver for Cirrus Logic EP93xx ADC

[Jonathan Cameron]

On 20/02/16 18:00, Alexander Sverdlin wrote:
> New driver adding support for ADC found on Cirrus Logic EP93xx series of SoCs.
> Board specific code must take care to create plaform device with all necessary
> resources.
> 
> Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Looks basically good to me.  A few things that might by convention in IIO
have been slightly different framed, but nothing that matters.

Given the need for the earlier arch related patches, this either needs to
got through the relevant arm-soc trees, or I need an Ack to apply those
through IIO.  I don't mind either way.  One aside though - is there anything
preventing us have this build with COMPILE_TEST as an alternative to the arch
dependency?  If not then adding that would be good to improve build test
coverage.  Note that you will probably need to check dependencies on one or
two things if you do that (HAS_IOMEM I would think for starters) which are
implicitly brought in otherwise by the ARCH dependency.

Should it go through the relevant arch trees then feel free to add.

Acked-by: Jonathan Cameron <jic23@kernel.org>

Thanks,

Jonathan
> ---
>  Documentation/iio/ep93xx_adc.txt |  29 +++++
>  drivers/iio/adc/Kconfig          |  11 ++
>  drivers/iio/adc/Makefile         |   1 +
>  drivers/iio/adc/ep93xx_adc.c     | 261 +++++++++++++++++++++++++++++++++++++++
>  4 files changed, 302 insertions(+)
>  create mode 100644 Documentation/iio/ep93xx_adc.txt
>  create mode 100644 drivers/iio/adc/ep93xx_adc.c
> 
> diff --git a/Documentation/iio/ep93xx_adc.txt b/Documentation/iio/ep93xx_adc.txt
> new file mode 100644
> index 0000000..321e59f
> --- /dev/null
> +++ b/Documentation/iio/ep93xx_adc.txt
> @@ -0,0 +1,29 @@
> +Cirrus Logic EP93xx ADC driver.
> +
> +1. Overview
> +
> +The driver is intended to work on both low-end (EP9301, EP9302) devices with
> +5-channel ADC and high-end (EP9307, EP9312, EP9315) devices with 10-channel
> +touchscreen/ADC module.
> +
> +2. Channel numbering
> +
> +Numbering scheme for channels 0..4 is defined in EP9301 and EP9302 datasheets.
> +EP9307, EP9312 and EP9312 have 3 channels more (total 8), but the numbering is
> +not defined. So the last three are numbered randomly, let's say.
> +
> +Assuming ep93xx_adc is IIO device0, you'd find following entries under
> +/sys/bus/iio/devices/iio:device0/:
> +
> +  +-----------------+---------------+
> +  | sysfs entry     | ball/pin name |
> +  +-----------------+---------------+
> +  | in_voltage0_raw | YM            |
> +  | in_voltage1_raw | SXP           |
> +  | in_voltage2_raw | SXM           |
> +  | in_voltage3_raw | SYP           |
> +  | in_voltage4_raw | SYM           |
> +  | in_voltage5_raw | XP            |
> +  | in_voltage6_raw | XM            |
> +  | in_voltage7_raw | YP            |
> +  +-----------------+---------------+
> diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
> index 283ded7..0482f29 100644
> --- a/drivers/iio/adc/Kconfig
> +++ b/drivers/iio/adc/Kconfig
> @@ -172,6 +172,17 @@ config DA9150_GPADC
>  	  To compile this driver as a module, choose M here: the module will be
>  	  called berlin2-adc.
> 
> +config EP93XX_ADC
> +	tristate "Cirrus Logic EP93XX ADC driver"
> +	depends on ARCH_EP93XX
> +	help
> +	  Driver for the ADC module on the EP93XX series of SoC from Cirrus Logic.
> +	  It's recommended to switch on CONFIG_HIGH_RES_TIMERS option, in this
> +	  case driver will reduce its CPU usage by 90% in some use cases.
> +
> +	  To compile this driver as a module, choose M here: the module will be
> +	  called ep93xx_adc.
> +
>  config EXYNOS_ADC
>  	tristate "Exynos ADC driver support"
>  	depends on ARCH_EXYNOS || ARCH_S3C24XX || ARCH_S3C64XX || (OF && COMPILE_TEST)
> diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
> index 6435780..cd7d33e 100644
> --- a/drivers/iio/adc/Makefile
> +++ b/drivers/iio/adc/Makefile
> @@ -18,6 +18,7 @@ obj-$(CONFIG_AXP288_ADC) += axp288_adc.o
>  obj-$(CONFIG_BERLIN2_ADC) += berlin2-adc.o
>  obj-$(CONFIG_CC10001_ADC) += cc10001_adc.o
>  obj-$(CONFIG_DA9150_GPADC) += da9150-gpadc.o
> +obj-$(CONFIG_EP93XX_ADC) += ep93xx_adc.o
>  obj-$(CONFIG_EXYNOS_ADC) += exynos_adc.o
>  obj-$(CONFIG_HI8435) += hi8435.o
>  obj-$(CONFIG_IMX7D_ADC) += imx7d_adc.o
> diff --git a/drivers/iio/adc/ep93xx_adc.c b/drivers/iio/adc/ep93xx_adc.c
> new file mode 100644
> index 0000000..3728591
> --- /dev/null
> +++ b/drivers/iio/adc/ep93xx_adc.c
> @@ -0,0 +1,261 @@
> +/*
> + * Driver for ADC module on the Cirrus Logic EP93xx series of SoCs
> + *
> + * Copyright (C) 2015 Alexander Sverdlin
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + *
> + * The driver uses polling to get the conversion status. According to EP93xx
> + * datasheets, reading ADCResult register starts the conversion, but user is also
> + * responsible for ensuring that delay between adjacent conversion triggers is
> + * long enough so that maximum allowed conversion rate is not exceeded. This
> + * basically renders IRQ mode unusable.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/device.h>
> +#include <linux/err.h>
> +#include <linux/iio/iio.h>
> +#include <linux/io.h>
> +#include <linux/irqflags.h>
> +#include <linux/module.h>
> +#include <linux/mutex.h>
> +#include <linux/platform_device.h>
> +
> +#define EP93XX_NUM_CHANNELS 8
> +
> +/*
> + * This code could benefit from real HR Timers, but jiffy granularity would
> + * lower ADC conversion rate down to CONFIG_HZ, so we fallback to busy wait
> + * in such case.
> + *
> + * HR Timers-based version loads CPU only up to 10% during back to back ADC
> + * conversion, while busy wait-based version consumes whole CPU power.
> + */
> +#ifdef CONFIG_HIGH_RES_TIMERS
> +#define ep93xx_adc_delay(usmin, usmax) usleep_range(usmin, usmax)
> +#else
> +#define ep93xx_adc_delay(usmin, usmax) udelay(usmin)
> +#endif
> +
> +#define EP93XX_ADC_RESULT	0x08
> +#define   EP93XX_ADC_SDR	BIT(31)
> +#define EP93XX_ADC_SWITCH	0x18
> +#define EP93XX_ADC_SW_LOCK	0x20
> +#define EP93XX_ADC_INT_EN	0x24
> +#define   EP93XX_ADC_RINTEN	BIT(11)
> +
> +struct ep93xx_adc_priv {
> +	struct clk *clk;
> +	void __iomem *base;
> +	int lastch;
> +	struct mutex lock;
> +};
> +
> +#define EP93XX_ADC_CH(index, dname, swcfg) {			\
> +	.type = IIO_VOLTAGE,					\
> +	.indexed = 1,						\
> +	.channel = index,					\
> +	.address = swcfg,					\
> +	.datasheet_name = dname,				\
> +	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),		\
> +	.info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SCALE) |	\
> +				   BIT(IIO_CHAN_INFO_OFFSET),	\
> +}
> +
> +/*
> + * Numbering scheme for channels 0..4 is defined in EP9301 and EP9302 datasheets.
> + * EP9307, EP9312 and EP9312 have 3 channels more (total 8), but the numbering is
> + * not defined. So the last three are numbered randomly, let's say.
> + */
> +static const struct iio_chan_spec ep93xx_adc_channels[EP93XX_NUM_CHANNELS] = {
> +	EP93XX_ADC_CH(0, "YM",	0x608),
> +	EP93XX_ADC_CH(1, "SXP",	0x680),
> +	EP93XX_ADC_CH(2, "SXM",	0x640),
> +	EP93XX_ADC_CH(3, "SYP",	0x620),
> +	EP93XX_ADC_CH(4, "SYM",	0x610),
> +	EP93XX_ADC_CH(5, "XP",	0x601),
> +	EP93XX_ADC_CH(6, "XM",	0x602),
> +	EP93XX_ADC_CH(7, "YP",	0x604),
> +};
> +
> +static int ep93xx_read_raw(struct iio_dev *iiodev,
> +			   struct iio_chan_spec const *channel, int *value,
> +			   int *shift, long mask)
> +{
> +	struct ep93xx_adc_priv *priv = iio_priv(iiodev);
> +	unsigned long timeout;
> +	int ret;
> +
> +	switch (mask) {
> +	case IIO_CHAN_INFO_RAW:
> +		mutex_lock(&priv->lock);
> +		if (priv->lastch != channel->channel) {
> +			priv->lastch = channel->channel;
> +			/*
> +			 * Switch register is software-locked, unlocking must be
> +			 * immediately followed by write
> +			 */
> +			local_irq_disable();
> +			writel_relaxed(0xAA, priv->base + EP93XX_ADC_SW_LOCK);
> +			writel_relaxed(channel->address,
> +				       priv->base + EP93XX_ADC_SWITCH);
> +			local_irq_enable();
> +			/*
> +			 * Settling delay depends on module clock and could be
> +			 * 2ms or 500us
> +			 */
> +			ep93xx_adc_delay(2000, 2000);
> +		}
> +		/* Start the conversion, eventually discarding old result */
> +		readl_relaxed(priv->base + EP93XX_ADC_RESULT);
> +		/* Ensure maximun conversion rate is not exceeded */
> +		ep93xx_adc_delay(DIV_ROUND_UP(1000000, 925),
> +				 DIV_ROUND_UP(1000000, 925));
> +		/* At this point conversion must be completed, but anyway... */
> +		ret = IIO_VAL_INT;
> +		timeout = jiffies + msecs_to_jiffies(1) + 1;
> +		while (1) {
> +			u32 t;
> +
> +			t = readl_relaxed(priv->base + EP93XX_ADC_RESULT);
> +			if (t & EP93XX_ADC_SDR) {
> +				/* Sign extend lower 16 bits */
> +				*value = (s16)t;
> +				break;
> +			}
> +
> +			if (time_after(jiffies, timeout)) {
> +				dev_err(&iiodev->dev, "Conversion timeout\n");
> +				ret = -ETIMEDOUT;
> +				break;
> +			}
> +
> +			cpu_relax();
> +		}
> +		mutex_unlock(&priv->lock);
> +		return ret;
> +
> +	case IIO_CHAN_INFO_OFFSET:
> +		/* According to datasheet, range is -25000..25000 */
> +		*value = 25000;
> +		return IIO_VAL_INT;
> +
> +	case IIO_CHAN_INFO_SCALE:
> +		/* Typical supply voltage is 3.3v */
> +		*value = (1ULL << 32) * 3300 / 50000;
> +		*shift = 32;
> +		return IIO_VAL_FRACTIONAL_LOG2;
> +	}
> +
> +	return -EINVAL;
> +}
> +
> +static const struct iio_info ep93xx_adc_info = {
> +	.driver_module = THIS_MODULE,
> +	.read_raw = ep93xx_read_raw,
> +};
> +
> +static int ep93xx_adc_probe(struct platform_device *pdev)
> +{
> +	int ret;
> +	struct iio_dev *iiodev;
> +	struct ep93xx_adc_priv *priv;
> +	struct clk *pclk;
> +	struct resource *res;
> +
> +	iiodev = devm_iio_device_alloc(&pdev->dev,
> +				       sizeof(struct ep93xx_adc_priv));
slight preference for sizeof(*priv)
> +	if (!iiodev)
> +		return -ENOMEM;
> +	priv = iio_priv(iiodev);
> +
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	if (!res) {
> +		dev_err(&pdev->dev, "Cannot obtain memory resource\n");
> +		return -ENXIO;
> +	}
> +	priv->base = devm_ioremap_resource(&pdev->dev, res);
> +	if (IS_ERR(priv->base)) {
> +		dev_err(&pdev->dev, "Cannot map memory resource\n");
> +		return PTR_ERR(priv->base);
> +	}
> +
> +	iiodev->dev.parent = &pdev->dev;
> +	iiodev->name = dev_name(&pdev->dev);
> +	iiodev->modes = INDIO_DIRECT_MODE;
> +	iiodev->info = &ep93xx_adc_info;
> +	iiodev->num_channels = ARRAY_SIZE(ep93xx_adc_channels);
> +	iiodev->channels = ep93xx_adc_channels;
> +
> +	priv->lastch = -1;
> +	mutex_init(&priv->lock);
> +
> +	platform_set_drvdata(pdev, iiodev);
> +
> +	priv->clk = devm_clk_get(&pdev->dev, NULL);
> +	if (IS_ERR(priv->clk)) {
> +		dev_err(&pdev->dev, "Cannot obtain clock\n");
> +		return PTR_ERR(priv->clk);
> +	}
> +
> +	pclk = clk_get_parent(priv->clk);
> +	if (!pclk) {
> +		dev_warn(&pdev->dev, "Cannot obtain parent clock\n");
> +	} else {
> +		/*
> +		 * This is actually a place for improvement:
> +		 * EP93xx ADC supports two clock divisors -- 4 and 16,
> +		 * resulting in conversion rates 3750 and 925 samples per second
> +		 * respectively with 500uS or 2ms settling time respectively.
> +		 * One might find this interesting enough to be configurable.
> +		 */
> +		ret = clk_set_rate(priv->clk, clk_get_rate(pclk) / 16);
> +		if (ret)
> +			dev_warn(&pdev->dev, "Cannot set clock rate\n");
> +		/*
> +		 * We can tolerate rate setting failure because the module should
> +		 * work in any case.
> +		 */
> +	}
> +
> +	ret = clk_enable(priv->clk);
> +	if (ret) {
> +		dev_err(&pdev->dev, "Cannot enable clock\n");
> +		return ret;
> +	}
> +
> +	ret = iio_device_register(iiodev);
> +	if (ret)
> +		clk_disable(priv->clk);
> +
> +	return ret;
> +}
> +
> +static int ep93xx_adc_remove(struct platform_device *pdev)
> +{
> +	struct iio_dev *iiodev = platform_get_drvdata(pdev);
> +	struct ep93xx_adc_priv *priv = iio_priv(iiodev);
> +
> +	iio_device_unregister(iiodev);
> +	clk_disable(priv->clk);
> +
> +	return 0;
> +}
> +
> +static struct platform_driver ep93xx_adc_driver = {
> +	.driver = {
> +		.name = "ep93xx-adc",
> +	},
> +	.probe = ep93xx_adc_probe,
> +	.remove = ep93xx_adc_remove,
> +};
> +module_platform_driver(ep93xx_adc_driver);
> +
> +MODULE_AUTHOR("Alexander Sverdlin <alexander.sverdlin@gmail.com>");
> +MODULE_DESCRIPTION("Cirrus Logic EP93XX ADC driver");
> +MODULE_LICENSE("GPL");
> +MODULE_ALIAS("platform:ep93xx-adc");
> 
> --
> To unsubscribe from this list: send the line "unsubscribe linux-iio" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
> 

[PATCH v2 5/5] iio: adc: New driver for Cirrus Logic EP93xx ADC

[Jonathan Cameron]

On 20/02/16 18:00, Alexander Sverdlin wrote:
> New driver adding support for ADC found on Cirrus Logic EP93xx series of SoCs.
> Board specific code must take care to create plaform device with all necessary
> resources.
> 
> Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Looks basically good to me.  A few things that might by convention in IIO
have been slightly different framed, but nothing that matters.

Given the need for the earlier arch related patches, this either needs to
got through the relevant arm-soc trees, or I need an Ack to apply those
through IIO.  I don't mind either way.  One aside though - is there anything
preventing us have this build with COMPILE_TEST as an alternative to the arch
dependency?  If not then adding that would be good to improve build test
coverage.  Note that you will probably need to check dependencies on one or
two things if you do that (HAS_IOMEM I would think for starters) which are
implicitly brought in otherwise by the ARCH dependency.

Should it go through the relevant arch trees then feel free to add.

Acked-by: Jonathan Cameron <jic23@kernel.org>

Thanks,

Jonathan
> ---
>  Documentation/iio/ep93xx_adc.txt |  29 +++++
>  drivers/iio/adc/Kconfig          |  11 ++
>  drivers/iio/adc/Makefile         |   1 +
>  drivers/iio/adc/ep93xx_adc.c     | 261 +++++++++++++++++++++++++++++++++++++++
>  4 files changed, 302 insertions(+)
>  create mode 100644 Documentation/iio/ep93xx_adc.txt
>  create mode 100644 drivers/iio/adc/ep93xx_adc.c
> 
> diff --git a/Documentation/iio/ep93xx_adc.txt b/Documentation/iio/ep93xx_adc.txt
> new file mode 100644
> index 0000000..321e59f
> --- /dev/null
> +++ b/Documentation/iio/ep93xx_adc.txt
> @@ -0,0 +1,29 @@
> +Cirrus Logic EP93xx ADC driver.
> +
> +1. Overview
> +
> +The driver is intended to work on both low-end (EP9301, EP9302) devices with
> +5-channel ADC and high-end (EP9307, EP9312, EP9315) devices with 10-channel
> +touchscreen/ADC module.
> +
> +2. Channel numbering
> +
> +Numbering scheme for channels 0..4 is defined in EP9301 and EP9302 datasheets.
> +EP9307, EP9312 and EP9312 have 3 channels more (total 8), but the numbering is
> +not defined. So the last three are numbered randomly, let's say.
> +
> +Assuming ep93xx_adc is IIO device0, you'd find following entries under
> +/sys/bus/iio/devices/iio:device0/:
> +
> +  +-----------------+---------------+
> +  | sysfs entry     | ball/pin name |
> +  +-----------------+---------------+
> +  | in_voltage0_raw | YM            |
> +  | in_voltage1_raw | SXP           |
> +  | in_voltage2_raw | SXM           |
> +  | in_voltage3_raw | SYP           |
> +  | in_voltage4_raw | SYM           |
> +  | in_voltage5_raw | XP            |
> +  | in_voltage6_raw | XM            |
> +  | in_voltage7_raw | YP            |
> +  +-----------------+---------------+
> diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
> index 283ded7..0482f29 100644
> --- a/drivers/iio/adc/Kconfig
> +++ b/drivers/iio/adc/Kconfig
> @@ -172,6 +172,17 @@ config DA9150_GPADC
>  	  To compile this driver as a module, choose M here: the module will be
>  	  called berlin2-adc.
> 
> +config EP93XX_ADC
> +	tristate "Cirrus Logic EP93XX ADC driver"
> +	depends on ARCH_EP93XX
> +	help
> +	  Driver for the ADC module on the EP93XX series of SoC from Cirrus Logic.
> +	  It's recommended to switch on CONFIG_HIGH_RES_TIMERS option, in this
> +	  case driver will reduce its CPU usage by 90% in some use cases.
> +
> +	  To compile this driver as a module, choose M here: the module will be
> +	  called ep93xx_adc.
> +
>  config EXYNOS_ADC
>  	tristate "Exynos ADC driver support"
>  	depends on ARCH_EXYNOS || ARCH_S3C24XX || ARCH_S3C64XX || (OF && COMPILE_TEST)
> diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
> index 6435780..cd7d33e 100644
> --- a/drivers/iio/adc/Makefile
> +++ b/drivers/iio/adc/Makefile
> @@ -18,6 +18,7 @@ obj-$(CONFIG_AXP288_ADC) += axp288_adc.o
>  obj-$(CONFIG_BERLIN2_ADC) += berlin2-adc.o
>  obj-$(CONFIG_CC10001_ADC) += cc10001_adc.o
>  obj-$(CONFIG_DA9150_GPADC) += da9150-gpadc.o
> +obj-$(CONFIG_EP93XX_ADC) += ep93xx_adc.o
>  obj-$(CONFIG_EXYNOS_ADC) += exynos_adc.o
>  obj-$(CONFIG_HI8435) += hi8435.o
>  obj-$(CONFIG_IMX7D_ADC) += imx7d_adc.o
> diff --git a/drivers/iio/adc/ep93xx_adc.c b/drivers/iio/adc/ep93xx_adc.c
> new file mode 100644
> index 0000000..3728591
> --- /dev/null
> +++ b/drivers/iio/adc/ep93xx_adc.c
> @@ -0,0 +1,261 @@
> +/*
> + * Driver for ADC module on the Cirrus Logic EP93xx series of SoCs
> + *
> + * Copyright (C) 2015 Alexander Sverdlin
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + *
> + * The driver uses polling to get the conversion status. According to EP93xx
> + * datasheets, reading ADCResult register starts the conversion, but user is also
> + * responsible for ensuring that delay between adjacent conversion triggers is
> + * long enough so that maximum allowed conversion rate is not exceeded. This
> + * basically renders IRQ mode unusable.
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/device.h>
> +#include <linux/err.h>
> +#include <linux/iio/iio.h>
> +#include <linux/io.h>
> +#include <linux/irqflags.h>
> +#include <linux/module.h>
> +#include <linux/mutex.h>
> +#include <linux/platform_device.h>
> +
> +#define EP93XX_NUM_CHANNELS 8
> +
> +/*
> + * This code could benefit from real HR Timers, but jiffy granularity would
> + * lower ADC conversion rate down to CONFIG_HZ, so we fallback to busy wait
> + * in such case.
> + *
> + * HR Timers-based version loads CPU only up to 10% during back to back ADC
> + * conversion, while busy wait-based version consumes whole CPU power.
> + */
> +#ifdef CONFIG_HIGH_RES_TIMERS
> +#define ep93xx_adc_delay(usmin, usmax) usleep_range(usmin, usmax)
> +#else
> +#define ep93xx_adc_delay(usmin, usmax) udelay(usmin)
> +#endif
> +
> +#define EP93XX_ADC_RESULT	0x08
> +#define   EP93XX_ADC_SDR	BIT(31)
> +#define EP93XX_ADC_SWITCH	0x18
> +#define EP93XX_ADC_SW_LOCK	0x20
> +#define EP93XX_ADC_INT_EN	0x24
> +#define   EP93XX_ADC_RINTEN	BIT(11)
> +
> +struct ep93xx_adc_priv {
> +	struct clk *clk;
> +	void __iomem *base;
> +	int lastch;
> +	struct mutex lock;
> +};
> +
> +#define EP93XX_ADC_CH(index, dname, swcfg) {			\
> +	.type = IIO_VOLTAGE,					\
> +	.indexed = 1,						\
> +	.channel = index,					\
> +	.address = swcfg,					\
> +	.datasheet_name = dname,				\
> +	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),		\
> +	.info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SCALE) |	\
> +				   BIT(IIO_CHAN_INFO_OFFSET),	\
> +}
> +
> +/*
> + * Numbering scheme for channels 0..4 is defined in EP9301 and EP9302 datasheets.
> + * EP9307, EP9312 and EP9312 have 3 channels more (total 8), but the numbering is
> + * not defined. So the last three are numbered randomly, let's say.
> + */
> +static const struct iio_chan_spec ep93xx_adc_channels[EP93XX_NUM_CHANNELS] = {
> +	EP93XX_ADC_CH(0, "YM",	0x608),
> +	EP93XX_ADC_CH(1, "SXP",	0x680),
> +	EP93XX_ADC_CH(2, "SXM",	0x640),
> +	EP93XX_ADC_CH(3, "SYP",	0x620),
> +	EP93XX_ADC_CH(4, "SYM",	0x610),
> +	EP93XX_ADC_CH(5, "XP",	0x601),
> +	EP93XX_ADC_CH(6, "XM",	0x602),
> +	EP93XX_ADC_CH(7, "YP",	0x604),
> +};
> +
> +static int ep93xx_read_raw(struct iio_dev *iiodev,
> +			   struct iio_chan_spec const *channel, int *value,
> +			   int *shift, long mask)
> +{
> +	struct ep93xx_adc_priv *priv = iio_priv(iiodev);
> +	unsigned long timeout;
> +	int ret;
> +
> +	switch (mask) {
> +	case IIO_CHAN_INFO_RAW:
> +		mutex_lock(&priv->lock);
> +		if (priv->lastch != channel->channel) {
> +			priv->lastch = channel->channel;
> +			/*
> +			 * Switch register is software-locked, unlocking must be
> +			 * immediately followed by write
> +			 */
> +			local_irq_disable();
> +			writel_relaxed(0xAA, priv->base + EP93XX_ADC_SW_LOCK);
> +			writel_relaxed(channel->address,
> +				       priv->base + EP93XX_ADC_SWITCH);
> +			local_irq_enable();
> +			/*
> +			 * Settling delay depends on module clock and could be
> +			 * 2ms or 500us
> +			 */
> +			ep93xx_adc_delay(2000, 2000);
> +		}
> +		/* Start the conversion, eventually discarding old result */
> +		readl_relaxed(priv->base + EP93XX_ADC_RESULT);
> +		/* Ensure maximun conversion rate is not exceeded */
> +		ep93xx_adc_delay(DIV_ROUND_UP(1000000, 925),
> +				 DIV_ROUND_UP(1000000, 925));
> +		/* At this point conversion must be completed, but anyway... */
> +		ret = IIO_VAL_INT;
> +		timeout = jiffies + msecs_to_jiffies(1) + 1;
> +		while (1) {
> +			u32 t;
> +
> +			t = readl_relaxed(priv->base + EP93XX_ADC_RESULT);
> +			if (t & EP93XX_ADC_SDR) {
> +				/* Sign extend lower 16 bits */
> +				*value = (s16)t;
> +				break;
> +			}
> +
> +			if (time_after(jiffies, timeout)) {
> +				dev_err(&iiodev->dev, "Conversion timeout\n");
> +				ret = -ETIMEDOUT;
> +				break;
> +			}
> +
> +			cpu_relax();
> +		}
> +		mutex_unlock(&priv->lock);
> +		return ret;
> +
> +	case IIO_CHAN_INFO_OFFSET:
> +		/* According to datasheet, range is -25000..25000 */
> +		*value = 25000;
> +		return IIO_VAL_INT;
> +
> +	case IIO_CHAN_INFO_SCALE:
> +		/* Typical supply voltage is 3.3v */
> +		*value = (1ULL << 32) * 3300 / 50000;
> +		*shift = 32;
> +		return IIO_VAL_FRACTIONAL_LOG2;
> +	}
> +
> +	return -EINVAL;
> +}
> +
> +static const struct iio_info ep93xx_adc_info = {
> +	.driver_module = THIS_MODULE,
> +	.read_raw = ep93xx_read_raw,
> +};
> +
> +static int ep93xx_adc_probe(struct platform_device *pdev)
> +{
> +	int ret;
> +	struct iio_dev *iiodev;
> +	struct ep93xx_adc_priv *priv;
> +	struct clk *pclk;
> +	struct resource *res;
> +
> +	iiodev = devm_iio_device_alloc(&pdev->dev,
> +				       sizeof(struct ep93xx_adc_priv));
slight preference for sizeof(*priv)
> +	if (!iiodev)
> +		return -ENOMEM;
> +	priv = iio_priv(iiodev);
> +
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	if (!res) {
> +		dev_err(&pdev->dev, "Cannot obtain memory resource\n");
> +		return -ENXIO;
> +	}
> +	priv->base = devm_ioremap_resource(&pdev->dev, res);
> +	if (IS_ERR(priv->base)) {
> +		dev_err(&pdev->dev, "Cannot map memory resource\n");
> +		return PTR_ERR(priv->base);
> +	}
> +
> +	iiodev->dev.parent = &pdev->dev;
> +	iiodev->name = dev_name(&pdev->dev);
> +	iiodev->modes = INDIO_DIRECT_MODE;
> +	iiodev->info = &ep93xx_adc_info;
> +	iiodev->num_channels = ARRAY_SIZE(ep93xx_adc_channels);
> +	iiodev->channels = ep93xx_adc_channels;
> +
> +	priv->lastch = -1;
> +	mutex_init(&priv->lock);
> +
> +	platform_set_drvdata(pdev, iiodev);
> +
> +	priv->clk = devm_clk_get(&pdev->dev, NULL);
> +	if (IS_ERR(priv->clk)) {
> +		dev_err(&pdev->dev, "Cannot obtain clock\n");
> +		return PTR_ERR(priv->clk);
> +	}
> +
> +	pclk = clk_get_parent(priv->clk);
> +	if (!pclk) {
> +		dev_warn(&pdev->dev, "Cannot obtain parent clock\n");
> +	} else {
> +		/*
> +		 * This is actually a place for improvement:
> +		 * EP93xx ADC supports two clock divisors -- 4 and 16,
> +		 * resulting in conversion rates 3750 and 925 samples per second
> +		 * respectively with 500uS or 2ms settling time respectively.
> +		 * One might find this interesting enough to be configurable.
> +		 */
> +		ret = clk_set_rate(priv->clk, clk_get_rate(pclk) / 16);
> +		if (ret)
> +			dev_warn(&pdev->dev, "Cannot set clock rate\n");
> +		/*
> +		 * We can tolerate rate setting failure because the module should
> +		 * work in any case.
> +		 */
> +	}
> +
> +	ret = clk_enable(priv->clk);
> +	if (ret) {
> +		dev_err(&pdev->dev, "Cannot enable clock\n");
> +		return ret;
> +	}
> +
> +	ret = iio_device_register(iiodev);
> +	if (ret)
> +		clk_disable(priv->clk);
> +
> +	return ret;
> +}
> +
> +static int ep93xx_adc_remove(struct platform_device *pdev)
> +{
> +	struct iio_dev *iiodev = platform_get_drvdata(pdev);
> +	struct ep93xx_adc_priv *priv = iio_priv(iiodev);
> +
> +	iio_device_unregister(iiodev);
> +	clk_disable(priv->clk);
> +
> +	return 0;
> +}
> +
> +static struct platform_driver ep93xx_adc_driver = {
> +	.driver = {
> +		.name = "ep93xx-adc",
> +	},
> +	.probe = ep93xx_adc_probe,
> +	.remove = ep93xx_adc_remove,
> +};
> +module_platform_driver(ep93xx_adc_driver);
> +
> +MODULE_AUTHOR("Alexander Sverdlin <alexander.sverdlin@gmail.com>");
> +MODULE_DESCRIPTION("Cirrus Logic EP93XX ADC driver");
> +MODULE_LICENSE("GPL");
> +MODULE_ALIAS("platform:ep93xx-adc");
> 
> --
> To unsubscribe from this list: send the line "unsubscribe linux-iio" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
>