* [U-Boot] [PATCH] sunxi: Support SID e-fuses on A83T and H3 @ 2016-01-27 8:34 Chen-Yu Tsai 2016-01-27 8:34 ` [U-Boot] [PATCH] sunxi: Add support for Cubietruck Plus Chen-Yu Tsai 2016-03-16 13:10 ` [U-Boot] sunxi: Support SID e-fuses on A83T and H3 Hans de Goede 0 siblings, 2 replies; 6+ messages in thread From: Chen-Yu Tsai @ 2016-01-27 8:34 UTC (permalink / raw) To: u-boot On the A83T and H3, the SID block is at a different address. Furthurmore, the e-fuses are at an offset of 0x200 within the hardware's address space. Signed-off-by: Chen-Yu Tsai <wens@csie.org> --- arch/arm/include/asm/arch-sunxi/cpu_sun4i.h | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/arch/arm/include/asm/arch-sunxi/cpu_sun4i.h b/arch/arm/include/asm/arch-sunxi/cpu_sun4i.h index 0cdefdc..f797649 100644 --- a/arch/arm/include/asm/arch-sunxi/cpu_sun4i.h +++ b/arch/arm/include/asm/arch-sunxi/cpu_sun4i.h @@ -74,7 +74,14 @@ #define SUNXI_AD_DA_BASE 0x01c22c00 #define SUNXI_KEYPAD_BASE 0x01c23000 #define SUNXI_TZPC_BASE 0x01c23400 + +#if defined(CONFIG_MACH_SUN8I_A83T) || defined(CONFIG_MACH_SUN8I_H3) +/* SID address space starts at 0x01c1400, but e-fuse is at offset 0x200 */ +#define SUNXI_SID_BASE 0x01c14200 +#else #define SUNXI_SID_BASE 0x01c23800 +#endif + #define SUNXI_SJTAG_BASE 0x01c23c00 #define SUNXI_TP_BASE 0x01c25000 -- 2.7.0 ^ permalink raw reply related [flat|nested] 6+ messages in thread
* [U-Boot] [PATCH] sunxi: Add support for Cubietruck Plus 2016-01-27 8:34 [U-Boot] [PATCH] sunxi: Support SID e-fuses on A83T and H3 Chen-Yu Tsai @ 2016-01-27 8:34 ` Chen-Yu Tsai 2016-03-19 22:43 ` Dennis Gilmore 2016-03-16 13:10 ` [U-Boot] sunxi: Support SID e-fuses on A83T and H3 Hans de Goede 1 sibling, 1 reply; 6+ messages in thread From: Chen-Yu Tsai @ 2016-01-27 8:34 UTC (permalink / raw) To: u-boot Cubietruck Plus is a A83T/H8 based development board. The board has standard DDR3 SDRAM, AXP818 PMIC/codec, SD/MMC, eMMC, USB 2.0 host via HSIC USB Hub, USB OTG, SATA via USB bridge, gigabit ethernet, WiFi, headphone out / mic in, and various GPIO headers. The board also has an EEPROM on i2c0 which holds the MAC address. DLDO3 and DLDO4 provide power to the EMAC pins and PHY. Pin PA20 is connected to the reset control of the PHY. EMAC is not actually supported yet. The DTS is the same as the one already in the kernel. Signed-off-by: Chen-Yu Tsai <wens@csie.org> --- arch/arm/dts/Makefile | 1 + arch/arm/dts/sun8i-a83t-cubietruck-plus.dts | 65 +++++++++++++++++++++++++++++ configs/Cubietruck_plus_defconfig | 18 ++++++++ 3 files changed, 84 insertions(+) create mode 100644 arch/arm/dts/sun8i-a83t-cubietruck-plus.dts create mode 100644 configs/Cubietruck_plus_defconfig diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile index 1c7d359..e338db5 100644 --- a/arch/arm/dts/Makefile +++ b/arch/arm/dts/Makefile @@ -184,6 +184,7 @@ dtb-$(CONFIG_MACH_SUN8I_A33) += \ sun8i-a33-sinlinx-sina33.dtb dtb-$(CONFIG_MACH_SUN8I_A83T) += \ sun8i-a83t-allwinner-h8homlet-v2.dtb \ + sun8i-a83t-cubietruck-plus.dtb \ sun8i-a83t-sinovoip-bpi-m3.dtb dtb-$(CONFIG_MACH_SUN8I_H3) += \ sun8i-h3-orangepi-pc.dtb \ diff --git a/arch/arm/dts/sun8i-a83t-cubietruck-plus.dts b/arch/arm/dts/sun8i-a83t-cubietruck-plus.dts new file mode 100644 index 0000000..88b1e09 --- /dev/null +++ b/arch/arm/dts/sun8i-a83t-cubietruck-plus.dts @@ -0,0 +1,65 @@ +/* + * Copyright 2015 Chen-Yu Tsai + * + * Chen-Yu Tsai <wens@csie.org> + * + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; +#include "sun8i-a83t.dtsi" + +/ { + model = "Cubietech Cubietruck Plus"; + compatible = "cubietech,cubietruck-plus", "allwinner,sun8i-a83t"; + + aliases { + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pins_b>; + status = "okay"; +}; diff --git a/configs/Cubietruck_plus_defconfig b/configs/Cubietruck_plus_defconfig new file mode 100644 index 0000000..bb0b336 --- /dev/null +++ b/configs/Cubietruck_plus_defconfig @@ -0,0 +1,18 @@ +CONFIG_ARM=y +CONFIG_ARCH_SUNXI=y +CONFIG_MACH_SUN8I_A83T=y +CONFIG_DRAM_CLK=672 +CONFIG_DRAM_ZQ=15355 +CONFIG_DRAM_ODT_EN=y +CONFIG_MMC0_CD_PIN="PF6" +CONFIG_I2C0_ENABLE=y +CONFIG_AXP_GPIO=y +CONFIG_DEFAULT_DEVICE_TREE="sun8i-a83t-cubietruck-plus" +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set +CONFIG_SPL=y +CONFIG_SYS_EXTRA_OPTIONS="RGMII,MACPWR=SUNXI_GPD(20)" +# CONFIG_CMD_IMLS is not set +# CONFIG_CMD_FLASH is not set +# CONFIG_CMD_FPGA is not set +CONFIG_AXP_DLDO3_VOLT=2500 +CONFIG_AXP_DLDO4_VOLT=3300 -- 2.7.0 ^ permalink raw reply related [flat|nested] 6+ messages in thread
* [U-Boot] [PATCH] sunxi: Add support for Cubietruck Plus 2016-01-27 8:34 ` [U-Boot] [PATCH] sunxi: Add support for Cubietruck Plus Chen-Yu Tsai @ 2016-03-19 22:43 ` Dennis Gilmore 2016-03-19 23:34 ` Dennis Gilmore 2016-03-20 13:47 ` [U-Boot] [linux-sunxi] " Hans de Goede 0 siblings, 2 replies; 6+ messages in thread From: Dennis Gilmore @ 2016-03-19 22:43 UTC (permalink / raw) To: u-boot Hans, What is the status of this patch? Dennis On Wednesday, January 27, 2016 4:34:44 PM CDT Chen-Yu Tsai wrote: > Cubietruck Plus is a A83T/H8 based development board. The board has > standard DDR3 SDRAM, AXP818 PMIC/codec, SD/MMC, eMMC, USB 2.0 host > via HSIC USB Hub, USB OTG, SATA via USB bridge, gigabit ethernet, > WiFi, headphone out / mic in, and various GPIO headers. > > The board also has an EEPROM on i2c0 which holds the MAC address. > > DLDO3 and DLDO4 provide power to the EMAC pins and PHY. Pin PA20 > is connected to the reset control of the PHY. EMAC is not actually > supported yet. > > The DTS is the same as the one already in the kernel. > > Signed-off-by: Chen-Yu Tsai <wens@csie.org> > --- > arch/arm/dts/Makefile | 1 + > arch/arm/dts/sun8i-a83t-cubietruck-plus.dts | 65 > +++++++++++++++++++++++++++++ configs/Cubietruck_plus_defconfig | > 18 ++++++++ > 3 files changed, 84 insertions(+) > create mode 100644 arch/arm/dts/sun8i-a83t-cubietruck-plus.dts > create mode 100644 configs/Cubietruck_plus_defconfig > > diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile > index 1c7d359..e338db5 100644 > --- a/arch/arm/dts/Makefile > +++ b/arch/arm/dts/Makefile > @@ -184,6 +184,7 @@ dtb-$(CONFIG_MACH_SUN8I_A33) += \ > sun8i-a33-sinlinx-sina33.dtb > dtb-$(CONFIG_MACH_SUN8I_A83T) += \ > sun8i-a83t-allwinner-h8homlet-v2.dtb \ > + sun8i-a83t-cubietruck-plus.dtb \ > sun8i-a83t-sinovoip-bpi-m3.dtb > dtb-$(CONFIG_MACH_SUN8I_H3) += \ > sun8i-h3-orangepi-pc.dtb \ > diff --git a/arch/arm/dts/sun8i-a83t-cubietruck-plus.dts > b/arch/arm/dts/sun8i-a83t-cubietruck-plus.dts new file mode 100644 > index 0000000..88b1e09 > --- /dev/null > +++ b/arch/arm/dts/sun8i-a83t-cubietruck-plus.dts > @@ -0,0 +1,65 @@ > +/* > + * Copyright 2015 Chen-Yu Tsai > + * > + * Chen-Yu Tsai <wens@csie.org> > + * > + * This file is dual-licensed: you can use it either under the terms > + * of the GPL or the X11 license, at your option. Note that this dual > + * licensing only applies to this file, and not this project as a > + * whole. > + * > + * a) This file is free software; you can redistribute it and/or > + * modify it under the terms of the GNU General Public License as > + * published by the Free Software Foundation; either version 2 of the > + * License, or (at your option) any later version. > + * > + * This file is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + * > + * Or, alternatively, > + * > + * b) Permission is hereby granted, free of charge, to any person > + * obtaining a copy of this software and associated documentation > + * files (the "Software"), to deal in the Software without > + * restriction, including without limitation the rights to use, > + * copy, modify, merge, publish, distribute, sublicense, and/or > + * sell copies of the Software, and to permit persons to whom the > + * Software is furnished to do so, subject to the following > + * conditions: > + * > + * The above copyright notice and this permission notice shall be > + * included in all copies or substantial portions of the Software. > + * > + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, > + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES > + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND > + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT > + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, > + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING > + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR > + * OTHER DEALINGS IN THE SOFTWARE. > + */ > + > +/dts-v1/; > +#include "sun8i-a83t.dtsi" > + > +/ { > + model = "Cubietech Cubietruck Plus"; > + compatible = "cubietech,cubietruck-plus", "allwinner,sun8i-a83t"; > + > + aliases { > + serial0 = &uart0; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > +}; > + > +&uart0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart0_pins_b>; > + status = "okay"; > +}; > diff --git a/configs/Cubietruck_plus_defconfig > b/configs/Cubietruck_plus_defconfig new file mode 100644 > index 0000000..bb0b336 > --- /dev/null > +++ b/configs/Cubietruck_plus_defconfig > @@ -0,0 +1,18 @@ > +CONFIG_ARM=y > +CONFIG_ARCH_SUNXI=y > +CONFIG_MACH_SUN8I_A83T=y > +CONFIG_DRAM_CLK=672 > +CONFIG_DRAM_ZQ=15355 > +CONFIG_DRAM_ODT_EN=y > +CONFIG_MMC0_CD_PIN="PF6" > +CONFIG_I2C0_ENABLE=y > +CONFIG_AXP_GPIO=y > +CONFIG_DEFAULT_DEVICE_TREE="sun8i-a83t-cubietruck-plus" > +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set > +CONFIG_SPL=y > +CONFIG_SYS_EXTRA_OPTIONS="RGMII,MACPWR=SUNXI_GPD(20)" > +# CONFIG_CMD_IMLS is not set > +# CONFIG_CMD_FLASH is not set > +# CONFIG_CMD_FPGA is not set > +CONFIG_AXP_DLDO3_VOLT=2500 > +CONFIG_AXP_DLDO4_VOLT=3300 ^ permalink raw reply [flat|nested] 6+ messages in thread
* [U-Boot] [PATCH] sunxi: Add support for Cubietruck Plus 2016-03-19 22:43 ` Dennis Gilmore @ 2016-03-19 23:34 ` Dennis Gilmore 2016-03-20 13:47 ` [U-Boot] [linux-sunxi] " Hans de Goede 1 sibling, 0 replies; 6+ messages in thread From: Dennis Gilmore @ 2016-03-19 23:34 UTC (permalink / raw) To: u-boot On Saturday, March 19, 2016 5:43:52 PM CDT Dennis Gilmore wrote: > Hans, > > What is the status of this patch? > > Dennis With the patch applied building for Cubietruck_plus fails with ld.bfd -pie --gc-sections -Bstatic -Ttext 0x4a000000 -o u-boot -T u- boot.lds arch/arm/cpu/armv7/start.o --start-group arch/arm/cpu/built-in.o arch/arm/cpu/armv7/built-in.o arch/arm/lib/built-in.o board/sunxi/built-in.o cmd/built-in.o common/built-in.o disk/built-in.o drivers/built-in.o drivers/dma/built-in.o drivers/gpio/built-in.o drivers/i2c/built-in.o drivers/mmc/built-in.o drivers/mtd/built-in.o drivers/mtd/onenand/built-in.o drivers/mtd/spi/built-in.o drivers/net/built-in.o drivers/net/phy/built-in.o drivers/pci/built-in.o drivers/power/built-in.o drivers/power/battery/built- in.o drivers/power/fuel_gauge/built-in.o drivers/power/mfd/built-in.o drivers/power/pmic/built-in.o drivers/power/regulator/built-in.o drivers/ serial/built-in.o drivers/spi/built-in.o drivers/usb/dwc3/built-in.o drivers/usb/emul/built-in.o drivers/usb/eth/built-in.o drivers/usb/gadget/ built-in.o drivers/usb/gadget/udc/built-in.o drivers/usb/host/built-in.o drivers/usb/musb-new/built-in.o drivers/usb/musb/built-in.o drivers/usb/phy/ built-in.o drivers/usb/ulpi/built-in.o fs/built-in.o lib/built-in.o net/ built-in.o test/built-in.o test/dm/built-in.o --end-group arch/arm/lib/ eabi_compat.o -L /usr/lib/gcc/armv7hl-redhat-linux-gnueabi/6.0.0 -lgcc -Map u-boot.map board/sunxi/built-in.o: In function `i2c_init_board': /builddir/build/BUILD/u-boot-2016.03/board/sunxi/board.c:363: undefined reference to `clock_twi_onoff' ld.bfd: BFD version 2.26.20160125 assertion fail elf32-arm.c:8434 ld.bfd: error: required section '.rel.plt' not found in the linker script ld.bfd: final link failed: Invalid operation > On Wednesday, January 27, 2016 4:34:44 PM CDT Chen-Yu Tsai wrote: > > Cubietruck Plus is a A83T/H8 based development board. The board has > > standard DDR3 SDRAM, AXP818 PMIC/codec, SD/MMC, eMMC, USB 2.0 host > > via HSIC USB Hub, USB OTG, SATA via USB bridge, gigabit ethernet, > > WiFi, headphone out / mic in, and various GPIO headers. > > > > The board also has an EEPROM on i2c0 which holds the MAC address. > > > > DLDO3 and DLDO4 provide power to the EMAC pins and PHY. Pin PA20 > > is connected to the reset control of the PHY. EMAC is not actually > > supported yet. > > > > The DTS is the same as the one already in the kernel. > > > > Signed-off-by: Chen-Yu Tsai <wens@csie.org> > > --- > > > > arch/arm/dts/Makefile | 1 + > > arch/arm/dts/sun8i-a83t-cubietruck-plus.dts | 65 > > > > +++++++++++++++++++++++++++++ configs/Cubietruck_plus_defconfig > > | > > 18 ++++++++ > > > > 3 files changed, 84 insertions(+) > > create mode 100644 arch/arm/dts/sun8i-a83t-cubietruck-plus.dts > > create mode 100644 configs/Cubietruck_plus_defconfig > > > > diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile > > index 1c7d359..e338db5 100644 > > --- a/arch/arm/dts/Makefile > > +++ b/arch/arm/dts/Makefile > > @@ -184,6 +184,7 @@ dtb-$(CONFIG_MACH_SUN8I_A33) += \ > > > > sun8i-a33-sinlinx-sina33.dtb > > > > dtb-$(CONFIG_MACH_SUN8I_A83T) += \ > > > > sun8i-a83t-allwinner-h8homlet-v2.dtb \ > > > > + sun8i-a83t-cubietruck-plus.dtb \ > > > > sun8i-a83t-sinovoip-bpi-m3.dtb > > > > dtb-$(CONFIG_MACH_SUN8I_H3) += \ > > > > sun8i-h3-orangepi-pc.dtb \ > > > > diff --git a/arch/arm/dts/sun8i-a83t-cubietruck-plus.dts > > b/arch/arm/dts/sun8i-a83t-cubietruck-plus.dts new file mode 100644 > > index 0000000..88b1e09 > > --- /dev/null > > +++ b/arch/arm/dts/sun8i-a83t-cubietruck-plus.dts > > @@ -0,0 +1,65 @@ > > +/* > > + * Copyright 2015 Chen-Yu Tsai > > + * > > + * Chen-Yu Tsai <wens@csie.org> > > + * > > + * This file is dual-licensed: you can use it either under the terms > > + * of the GPL or the X11 license, at your option. Note that this dual > > + * licensing only applies to this file, and not this project as a > > + * whole. > > + * > > + * a) This file is free software; you can redistribute it and/or > > + * modify it under the terms of the GNU General Public License as > > + * published by the Free Software Foundation; either version 2 of the > > + * License, or (at your option) any later version. > > + * > > + * This file is distributed in the hope that it will be useful, > > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > > + * GNU General Public License for more details. > > + * > > + * Or, alternatively, > > + * > > + * b) Permission is hereby granted, free of charge, to any person > > + * obtaining a copy of this software and associated documentation > > + * files (the "Software"), to deal in the Software without > > + * restriction, including without limitation the rights to use, > > + * copy, modify, merge, publish, distribute, sublicense, and/or > > + * sell copies of the Software, and to permit persons to whom the > > + * Software is furnished to do so, subject to the following > > + * conditions: > > + * > > + * The above copyright notice and this permission notice shall be > > + * included in all copies or substantial portions of the Software. > > + * > > + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, > > + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES > > + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND > > + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT > > + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, > > + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING > > + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR > > + * OTHER DEALINGS IN THE SOFTWARE. > > + */ > > + > > +/dts-v1/; > > +#include "sun8i-a83t.dtsi" > > + > > +/ { > > + model = "Cubietech Cubietruck Plus"; > > + compatible = "cubietech,cubietruck-plus", "allwinner,sun8i-a83t"; > > + > > + aliases { > > + serial0 = &uart0; > > + }; > > + > > + chosen { > > + stdout-path = "serial0:115200n8"; > > + }; > > +}; > > + > > +&uart0 { > > + pinctrl-names = "default"; > > + pinctrl-0 = <&uart0_pins_b>; > > + status = "okay"; > > +}; > > diff --git a/configs/Cubietruck_plus_defconfig > > b/configs/Cubietruck_plus_defconfig new file mode 100644 > > index 0000000..bb0b336 > > --- /dev/null > > +++ b/configs/Cubietruck_plus_defconfig > > @@ -0,0 +1,18 @@ > > +CONFIG_ARM=y > > +CONFIG_ARCH_SUNXI=y > > +CONFIG_MACH_SUN8I_A83T=y > > +CONFIG_DRAM_CLK=672 > > +CONFIG_DRAM_ZQ=15355 > > +CONFIG_DRAM_ODT_EN=y > > +CONFIG_MMC0_CD_PIN="PF6" > > +CONFIG_I2C0_ENABLE=y > > +CONFIG_AXP_GPIO=y > > +CONFIG_DEFAULT_DEVICE_TREE="sun8i-a83t-cubietruck-plus" > > +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set > > +CONFIG_SPL=y > > +CONFIG_SYS_EXTRA_OPTIONS="RGMII,MACPWR=SUNXI_GPD(20)" > > +# CONFIG_CMD_IMLS is not set > > +# CONFIG_CMD_FLASH is not set > > +# CONFIG_CMD_FPGA is not set > > +CONFIG_AXP_DLDO3_VOLT=2500 > > +CONFIG_AXP_DLDO4_VOLT=3300 > > _______________________________________________ > U-Boot mailing list > U-Boot at lists.denx.de > http://lists.denx.de/mailman/listinfo/u-boot -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: This is a digitally signed message part. URL: <http://lists.denx.de/pipermail/u-boot/attachments/20160319/c818a94d/attachment.sig> ^ permalink raw reply [flat|nested] 6+ messages in thread
* [U-Boot] [linux-sunxi] Re: [PATCH] sunxi: Add support for Cubietruck Plus 2016-03-19 22:43 ` Dennis Gilmore 2016-03-19 23:34 ` Dennis Gilmore @ 2016-03-20 13:47 ` Hans de Goede 1 sibling, 0 replies; 6+ messages in thread From: Hans de Goede @ 2016-03-20 13:47 UTC (permalink / raw) To: u-boot hI, On 19-03-16 23:43, Dennis Gilmore wrote: > Hans, > > What is the status of this patch? I added this to my sunxi-wip tree (including a fix for the build error) a couple of days ago. I will send a pull-req for various u-boot sunxi patch soonish and then it will hit mainline. Regards, Hans > > Dennis > > On Wednesday, January 27, 2016 4:34:44 PM CDT Chen-Yu Tsai wrote: >> Cubietruck Plus is a A83T/H8 based development board. The board has >> standard DDR3 SDRAM, AXP818 PMIC/codec, SD/MMC, eMMC, USB 2.0 host >> via HSIC USB Hub, USB OTG, SATA via USB bridge, gigabit ethernet, >> WiFi, headphone out / mic in, and various GPIO headers. >> >> The board also has an EEPROM on i2c0 which holds the MAC address. >> >> DLDO3 and DLDO4 provide power to the EMAC pins and PHY. Pin PA20 >> is connected to the reset control of the PHY. EMAC is not actually >> supported yet. >> >> The DTS is the same as the one already in the kernel. >> >> Signed-off-by: Chen-Yu Tsai <wens@csie.org> >> --- >> arch/arm/dts/Makefile | 1 + >> arch/arm/dts/sun8i-a83t-cubietruck-plus.dts | 65 >> +++++++++++++++++++++++++++++ configs/Cubietruck_plus_defconfig | >> 18 ++++++++ >> 3 files changed, 84 insertions(+) >> create mode 100644 arch/arm/dts/sun8i-a83t-cubietruck-plus.dts >> create mode 100644 configs/Cubietruck_plus_defconfig >> >> diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile >> index 1c7d359..e338db5 100644 >> --- a/arch/arm/dts/Makefile >> +++ b/arch/arm/dts/Makefile >> @@ -184,6 +184,7 @@ dtb-$(CONFIG_MACH_SUN8I_A33) += \ >> sun8i-a33-sinlinx-sina33.dtb >> dtb-$(CONFIG_MACH_SUN8I_A83T) += \ >> sun8i-a83t-allwinner-h8homlet-v2.dtb \ >> + sun8i-a83t-cubietruck-plus.dtb \ >> sun8i-a83t-sinovoip-bpi-m3.dtb >> dtb-$(CONFIG_MACH_SUN8I_H3) += \ >> sun8i-h3-orangepi-pc.dtb \ >> diff --git a/arch/arm/dts/sun8i-a83t-cubietruck-plus.dts >> b/arch/arm/dts/sun8i-a83t-cubietruck-plus.dts new file mode 100644 >> index 0000000..88b1e09 >> --- /dev/null >> +++ b/arch/arm/dts/sun8i-a83t-cubietruck-plus.dts >> @@ -0,0 +1,65 @@ >> +/* >> + * Copyright 2015 Chen-Yu Tsai >> + * >> + * Chen-Yu Tsai <wens@csie.org> >> + * >> + * This file is dual-licensed: you can use it either under the terms >> + * of the GPL or the X11 license, at your option. Note that this dual >> + * licensing only applies to this file, and not this project as a >> + * whole. >> + * >> + * a) This file is free software; you can redistribute it and/or >> + * modify it under the terms of the GNU General Public License as >> + * published by the Free Software Foundation; either version 2 of the >> + * License, or (at your option) any later version. >> + * >> + * This file is distributed in the hope that it will be useful, >> + * but WITHOUT ANY WARRANTY; without even the implied warranty of >> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the >> + * GNU General Public License for more details. >> + * >> + * Or, alternatively, >> + * >> + * b) Permission is hereby granted, free of charge, to any person >> + * obtaining a copy of this software and associated documentation >> + * files (the "Software"), to deal in the Software without >> + * restriction, including without limitation the rights to use, >> + * copy, modify, merge, publish, distribute, sublicense, and/or >> + * sell copies of the Software, and to permit persons to whom the >> + * Software is furnished to do so, subject to the following >> + * conditions: >> + * >> + * The above copyright notice and this permission notice shall be >> + * included in all copies or substantial portions of the Software. >> + * >> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, >> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES >> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND >> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT >> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, >> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING >> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR >> + * OTHER DEALINGS IN THE SOFTWARE. >> + */ >> + >> +/dts-v1/; >> +#include "sun8i-a83t.dtsi" >> + >> +/ { >> + model = "Cubietech Cubietruck Plus"; >> + compatible = "cubietech,cubietruck-plus", "allwinner,sun8i-a83t"; >> + >> + aliases { >> + serial0 = &uart0; >> + }; >> + >> + chosen { >> + stdout-path = "serial0:115200n8"; >> + }; >> +}; >> + >> +&uart0 { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&uart0_pins_b>; >> + status = "okay"; >> +}; >> diff --git a/configs/Cubietruck_plus_defconfig >> b/configs/Cubietruck_plus_defconfig new file mode 100644 >> index 0000000..bb0b336 >> --- /dev/null >> +++ b/configs/Cubietruck_plus_defconfig >> @@ -0,0 +1,18 @@ >> +CONFIG_ARM=y >> +CONFIG_ARCH_SUNXI=y >> +CONFIG_MACH_SUN8I_A83T=y >> +CONFIG_DRAM_CLK=672 >> +CONFIG_DRAM_ZQ=15355 >> +CONFIG_DRAM_ODT_EN=y >> +CONFIG_MMC0_CD_PIN="PF6" >> +CONFIG_I2C0_ENABLE=y >> +CONFIG_AXP_GPIO=y >> +CONFIG_DEFAULT_DEVICE_TREE="sun8i-a83t-cubietruck-plus" >> +# CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set >> +CONFIG_SPL=y >> +CONFIG_SYS_EXTRA_OPTIONS="RGMII,MACPWR=SUNXI_GPD(20)" >> +# CONFIG_CMD_IMLS is not set >> +# CONFIG_CMD_FLASH is not set >> +# CONFIG_CMD_FPGA is not set >> +CONFIG_AXP_DLDO3_VOLT=2500 >> +CONFIG_AXP_DLDO4_VOLT=3300 > > ^ permalink raw reply [flat|nested] 6+ messages in thread
* [U-Boot] sunxi: Support SID e-fuses on A83T and H3 2016-01-27 8:34 [U-Boot] [PATCH] sunxi: Support SID e-fuses on A83T and H3 Chen-Yu Tsai 2016-01-27 8:34 ` [U-Boot] [PATCH] sunxi: Add support for Cubietruck Plus Chen-Yu Tsai @ 2016-03-16 13:10 ` Hans de Goede 1 sibling, 0 replies; 6+ messages in thread From: Hans de Goede @ 2016-03-16 13:10 UTC (permalink / raw) To: u-boot Hi, On 27-01-16 09:34, Chen-Yu Tsai wrote: > On the A83T and H3, the SID block is at a different address. > Furthurmore, the e-fuses are at an offset of 0x200 within the > hardware's address space. > > Signed-off-by: Chen-Yu Tsai <wens@csie.org> Thanks, applied to my tree and this will go out with the next pull-req. Regards, Hans > --- > arch/arm/include/asm/arch-sunxi/cpu_sun4i.h | 7 +++++++ > 1 file changed, 7 insertions(+) > > diff --git a/arch/arm/include/asm/arch-sunxi/cpu_sun4i.h b/arch/arm/include/asm/arch-sunxi/cpu_sun4i.h > index 0cdefdc..f797649 100644 > --- a/arch/arm/include/asm/arch-sunxi/cpu_sun4i.h > +++ b/arch/arm/include/asm/arch-sunxi/cpu_sun4i.h > @@ -74,7 +74,14 @@ > #define SUNXI_AD_DA_BASE 0x01c22c00 > #define SUNXI_KEYPAD_BASE 0x01c23000 > #define SUNXI_TZPC_BASE 0x01c23400 > + > +#if defined(CONFIG_MACH_SUN8I_A83T) || defined(CONFIG_MACH_SUN8I_H3) > +/* SID address space starts at 0x01c1400, but e-fuse is at offset 0x200 */ > +#define SUNXI_SID_BASE 0x01c14200 > +#else > #define SUNXI_SID_BASE 0x01c23800 > +#endif > + > #define SUNXI_SJTAG_BASE 0x01c23c00 > > #define SUNXI_TP_BASE 0x01c25000 > ^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2016-03-20 13:47 UTC | newest] Thread overview: 6+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2016-01-27 8:34 [U-Boot] [PATCH] sunxi: Support SID e-fuses on A83T and H3 Chen-Yu Tsai 2016-01-27 8:34 ` [U-Boot] [PATCH] sunxi: Add support for Cubietruck Plus Chen-Yu Tsai 2016-03-19 22:43 ` Dennis Gilmore 2016-03-19 23:34 ` Dennis Gilmore 2016-03-20 13:47 ` [U-Boot] [linux-sunxi] " Hans de Goede 2016-03-16 13:10 ` [U-Boot] sunxi: Support SID e-fuses on A83T and H3 Hans de Goede
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.