* [U-Boot] [PATCH 1/2] warp7: Pass the UART base definition
@ 2016-03-26 16:30 Fabio Estevam
2016-03-26 16:30 ` [U-Boot] [PATCH 2/2] mx7_common: Define CONFIG_SYS_MALLOC_LEN in the board file Fabio Estevam
2016-04-03 17:17 ` [U-Boot] [PATCH 1/2] warp7: Pass the UART base definition Stefano Babic
0 siblings, 2 replies; 4+ messages in thread
From: Fabio Estevam @ 2016-03-26 16:30 UTC (permalink / raw)
To: u-boot
From: Fabio Estevam <fabio.estevam@nxp.com>
Since commit 5d69269deed0 ("mx7dsabresd: Define serial port locally")
we need to specify the UART base address in each board config
file, so do this to avoid a build error.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
---
include/configs/warp7.h | 2 ++
1 file changed, 2 insertions(+)
diff --git a/include/configs/warp7.h b/include/configs/warp7.h
index 0798671..5ea5512 100644
--- a/include/configs/warp7.h
+++ b/include/configs/warp7.h
@@ -14,6 +14,8 @@
#define PHYS_SDRAM_SIZE SZ_512M
+#define CONFIG_MXC_UART_BASE UART1_IPS_BASE_ADDR
+
#define CONFIG_BOARD_EARLY_INIT_F
/* MMC Config*/
--
1.9.1
^ permalink raw reply related [flat|nested] 4+ messages in thread
* [U-Boot] [PATCH 2/2] mx7_common: Define CONFIG_SYS_MALLOC_LEN in the board file
2016-03-26 16:30 [U-Boot] [PATCH 1/2] warp7: Pass the UART base definition Fabio Estevam
@ 2016-03-26 16:30 ` Fabio Estevam
2016-04-03 17:17 ` Stefano Babic
2016-04-03 17:17 ` [U-Boot] [PATCH 1/2] warp7: Pass the UART base definition Stefano Babic
1 sibling, 1 reply; 4+ messages in thread
From: Fabio Estevam @ 2016-03-26 16:30 UTC (permalink / raw)
To: u-boot
From: Fabio Estevam <fabio.estevam@nxp.com>
Having CONFIG_SYS_MALLOC_LEN in mx7_common.h is not a good idea,
because the malloc() pool size is board dependent.
For example: if a certain board has support for splashscreen or DFU,
it may be necessary to adjust CONFIG_SYS_MALLOC_LEN to a larger value.
So define CONFIG_SYS_MALLOC_LEN in each board config file.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
---
include/configs/mx7_common.h | 3 ---
include/configs/mx7dsabresd.h | 3 +++
include/configs/warp7.h | 4 ++++
3 files changed, 7 insertions(+), 3 deletions(-)
diff --git a/include/configs/mx7_common.h b/include/configs/mx7_common.h
index 5034464..9bd6114 100644
--- a/include/configs/mx7_common.h
+++ b/include/configs/mx7_common.h
@@ -28,9 +28,6 @@
/* Enable iomux-lpsr support */
#define CONFIG_IOMUX_LPSR
-/* Size of malloc() pool */
-#define CONFIG_SYS_MALLOC_LEN (32 * SZ_1M)
-
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
diff --git a/include/configs/mx7dsabresd.h b/include/configs/mx7dsabresd.h
index 988d363..25ed29d 100644
--- a/include/configs/mx7dsabresd.h
+++ b/include/configs/mx7dsabresd.h
@@ -16,6 +16,9 @@
#define CONFIG_MXC_UART_BASE UART1_IPS_BASE_ADDR
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (32 * SZ_1M)
+
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_BOARD_LATE_INIT
diff --git a/include/configs/warp7.h b/include/configs/warp7.h
index 5ea5512..d1404b2 100644
--- a/include/configs/warp7.h
+++ b/include/configs/warp7.h
@@ -16,6 +16,10 @@
#define CONFIG_MXC_UART_BASE UART1_IPS_BASE_ADDR
+
+/* Size of malloc() pool */
+#define CONFIG_SYS_MALLOC_LEN (32 * SZ_1M)
+
#define CONFIG_BOARD_EARLY_INIT_F
/* MMC Config*/
--
1.9.1
^ permalink raw reply related [flat|nested] 4+ messages in thread
* [U-Boot] [PATCH 1/2] warp7: Pass the UART base definition
2016-03-26 16:30 [U-Boot] [PATCH 1/2] warp7: Pass the UART base definition Fabio Estevam
2016-03-26 16:30 ` [U-Boot] [PATCH 2/2] mx7_common: Define CONFIG_SYS_MALLOC_LEN in the board file Fabio Estevam
@ 2016-04-03 17:17 ` Stefano Babic
1 sibling, 0 replies; 4+ messages in thread
From: Stefano Babic @ 2016-04-03 17:17 UTC (permalink / raw)
To: u-boot
On 26/03/2016 17:30, Fabio Estevam wrote:
> From: Fabio Estevam <fabio.estevam@nxp.com>
>
> Since commit 5d69269deed0 ("mx7dsabresd: Define serial port locally")
> we need to specify the UART base address in each board config
> file, so do this to avoid a build error.
>
> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
> ---
> include/configs/warp7.h | 2 ++
> 1 file changed, 2 insertions(+)
>
> diff --git a/include/configs/warp7.h b/include/configs/warp7.h
> index 0798671..5ea5512 100644
> --- a/include/configs/warp7.h
> +++ b/include/configs/warp7.h
> @@ -14,6 +14,8 @@
>
> #define PHYS_SDRAM_SIZE SZ_512M
>
> +#define CONFIG_MXC_UART_BASE UART1_IPS_BASE_ADDR
> +
> #define CONFIG_BOARD_EARLY_INIT_F
>
> /* MMC Config*/
>
Applied to u-boot-imx, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 4+ messages in thread
* [U-Boot] [PATCH 2/2] mx7_common: Define CONFIG_SYS_MALLOC_LEN in the board file
2016-03-26 16:30 ` [U-Boot] [PATCH 2/2] mx7_common: Define CONFIG_SYS_MALLOC_LEN in the board file Fabio Estevam
@ 2016-04-03 17:17 ` Stefano Babic
0 siblings, 0 replies; 4+ messages in thread
From: Stefano Babic @ 2016-04-03 17:17 UTC (permalink / raw)
To: u-boot
On 26/03/2016 17:30, Fabio Estevam wrote:
> From: Fabio Estevam <fabio.estevam@nxp.com>
>
> Having CONFIG_SYS_MALLOC_LEN in mx7_common.h is not a good idea,
> because the malloc() pool size is board dependent.
>
> For example: if a certain board has support for splashscreen or DFU,
> it may be necessary to adjust CONFIG_SYS_MALLOC_LEN to a larger value.
>
> So define CONFIG_SYS_MALLOC_LEN in each board config file.
>
> Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
> ---
> include/configs/mx7_common.h | 3 ---
> include/configs/mx7dsabresd.h | 3 +++
> include/configs/warp7.h | 4 ++++
> 3 files changed, 7 insertions(+), 3 deletions(-)
>
> diff --git a/include/configs/mx7_common.h b/include/configs/mx7_common.h
> index 5034464..9bd6114 100644
> --- a/include/configs/mx7_common.h
> +++ b/include/configs/mx7_common.h
> @@ -28,9 +28,6 @@
> /* Enable iomux-lpsr support */
> #define CONFIG_IOMUX_LPSR
>
> -/* Size of malloc() pool */
> -#define CONFIG_SYS_MALLOC_LEN (32 * SZ_1M)
> -
> #define CONFIG_DISPLAY_CPUINFO
> #define CONFIG_DISPLAY_BOARDINFO
>
> diff --git a/include/configs/mx7dsabresd.h b/include/configs/mx7dsabresd.h
> index 988d363..25ed29d 100644
> --- a/include/configs/mx7dsabresd.h
> +++ b/include/configs/mx7dsabresd.h
> @@ -16,6 +16,9 @@
>
> #define CONFIG_MXC_UART_BASE UART1_IPS_BASE_ADDR
>
> +/* Size of malloc() pool */
> +#define CONFIG_SYS_MALLOC_LEN (32 * SZ_1M)
> +
> #define CONFIG_BOARD_EARLY_INIT_F
> #define CONFIG_BOARD_LATE_INIT
>
> diff --git a/include/configs/warp7.h b/include/configs/warp7.h
> index 5ea5512..d1404b2 100644
> --- a/include/configs/warp7.h
> +++ b/include/configs/warp7.h
> @@ -16,6 +16,10 @@
>
> #define CONFIG_MXC_UART_BASE UART1_IPS_BASE_ADDR
>
> +
> +/* Size of malloc() pool */
> +#define CONFIG_SYS_MALLOC_LEN (32 * SZ_1M)
> +
> #define CONFIG_BOARD_EARLY_INIT_F
>
> /* MMC Config*/
>
Applied to u-boot-imx, thanks !
Best regards,
Stefano Babic
--
=====================================================================
DENX Software Engineering GmbH, Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: sbabic at denx.de
=====================================================================
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2016-04-03 17:17 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2016-03-26 16:30 [U-Boot] [PATCH 1/2] warp7: Pass the UART base definition Fabio Estevam
2016-03-26 16:30 ` [U-Boot] [PATCH 2/2] mx7_common: Define CONFIG_SYS_MALLOC_LEN in the board file Fabio Estevam
2016-04-03 17:17 ` Stefano Babic
2016-04-03 17:17 ` [U-Boot] [PATCH 1/2] warp7: Pass the UART base definition Stefano Babic
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.