Re: [PATCH 3/3] input: touchscreen: mxs-lradc: Add support for touchscreen

[Marek Vasut <marex-ynQEQJNshbs@public.gmane.org>]

On 04/30/2016 01:36 AM, Dmitry Torokhov wrote:
> Hi Ksenija,

Hi all,

> On Fri, Apr 29, 2016 at 01:49:11PM +0200, Ksenija Stanojevic wrote:
>> Add mxs-lradc touchscreen driver.
>>
>> Signed-off-by: Ksenija Stanojevic <ksenija.stanojevic-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
>> ---
>>  drivers/input/touchscreen/Kconfig        |  14 +-
>>  drivers/input/touchscreen/Makefile       |   1 +
>>  drivers/input/touchscreen/mxs-lradc-ts.c | 729 +++++++++++++++++++++++++++++++
>>  3 files changed, 742 insertions(+), 2 deletions(-)
>>  create mode 100644 drivers/input/touchscreen/mxs-lradc-ts.c
>>
>> diff --git a/drivers/input/touchscreen/Kconfig b/drivers/input/touchscreen/Kconfig
>> index 8ecdc38..d614d248 100644
>> --- a/drivers/input/touchscreen/Kconfig
>> +++ b/drivers/input/touchscreen/Kconfig
>> @@ -566,7 +566,7 @@ config TOUCHSCREEN_HP600
>>  	depends on SH_HP6XX && SH_ADC
>>  	help
>>  	  Say Y here if you have a HP Jornada 620/660/680/690 and want to
>> -          support the built-in touchscreen.
>> +	  support the built-in touchscreen.
>>  
>>  	  To compile this driver as a module, choose M here: the
>>  	  module will be called hp680_ts_input.
>> @@ -685,7 +685,7 @@ config TOUCHSCREEN_UCB1400
>>  	  This enables support for the Philips UCB1400 touchscreen interface.
>>  	  The UCB1400 is an AC97 audio codec.  The touchscreen interface
>>  	  will be initialized only after the ALSA subsystem has been
>> -	  brought up and the UCB1400 detected.  You therefore have to
>> +	  brought up and the UCB1400 detected.	You therefore have to
> 
> Why do we have the tab in the middle of the text?

This shouldn't be a part of the patch.

>>  	  configure ALSA support as well (either built-in or modular,
>>  	  independently of whether this driver is itself built-in or
>>  	  modular) for this driver to work.

[...]

>> +
>> +	return 0;
>> +}
>> +
>> +static struct platform_driver mxs_lradc_ts_driver = {
>> +	.driver	= {
>> +		.name = DRIVER_NAME_TS,
>> +	},
>> +	.probe	= mxs_lradc_ts_probe,
>> +	.remove	= mxs_lradc_ts_remove,
>> +};
>> +module_platform_driver(mxs_lradc_ts_driver);
>> +
>> +MODULE_LICENSE("GPL v2");
> 
> "GPL" since you are not limiting to v2 only.

The original driver ( drivers/iio/adc/mxs-lradc.c ) is GPLv2 , but
unless the license gets changed to BSD or somesuch, I don't think anyone
will really complain if it's changed to a more fitting version(s) of
GPL. I'm fine with any GPL version here.

Thanks for the thorough review, some points were new to me.

> Thanks.
> 


-- 
Best regards,
Marek Vasut