* [PATCH v2] extcon: Add support for qcom SPMI PMIC USB id detection hardware @ 2016-09-09 21:48 ` Stephen Boyd 0 siblings, 0 replies; 6+ messages in thread From: Stephen Boyd @ 2016-09-09 21:48 UTC (permalink / raw) To: Chanwoo Choi; +Cc: linux-arm-kernel, linux-kernel, linux-arm-msm, Roger Quadros Some Qualcomm PMICs have a misc device that performs USB id pin detection via an interrupt. When the interrupt triggers, we should read the interrupt line to see if it has gone high or low. If the interrupt is low then the ID pin is grounded, and if the interrupt is high then the ID pin is being held high. Cc: Roger Quadros <rogerq@ti.com> Cc: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> --- Changes from v1: * Fixed Makefile ordering * Fixed up copyright markings .../bindings/extcon/qcom,pm8941-misc.txt | 41 +++++ drivers/extcon/Kconfig | 6 + drivers/extcon/Makefile | 1 + drivers/extcon/extcon-qcom-spmi-misc.c | 167 +++++++++++++++++++++ 4 files changed, 215 insertions(+) create mode 100644 Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt create mode 100644 drivers/extcon/extcon-qcom-spmi-misc.c diff --git a/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt b/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt new file mode 100644 index 000000000000..35383adb10f1 --- /dev/null +++ b/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt @@ -0,0 +1,41 @@ +Qualcomm's PM8941 USB ID Extcon device + +Some Qualcomm PMICs have a "misc" module that can be used to detect when +the USB ID pin has been pulled low or high. + +PROPERTIES + +- compatible: + Usage: required + Value type: <string> + Definition: Should contain "qcom,pm8941-misc"; + +- reg: + Usage: required + Value type: <u32> + Definition: Should contain the offset to the misc address space + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: Should contain the usb id interrupt + +- interrupt-names: + Usage: required + Value type: <stringlist> + Definition: Should contain the string "usb_id" for the usb id interrupt + +Example: + + pmic { + usb_id: misc@900 { + compatible = "qcom,pm8941-misc"; + reg = <0x900>; + interrupts = <0x0 0x9 0 IRQ_TYPE_EDGE_BOTH>; + interrupt-names = "usb_id"; + }; + } + + usb-controller { + extcon = <&usb_id>; + }; diff --git a/drivers/extcon/Kconfig b/drivers/extcon/Kconfig index 3d89e60a3e71..04788d92ea52 100644 --- a/drivers/extcon/Kconfig +++ b/drivers/extcon/Kconfig @@ -96,6 +96,12 @@ config EXTCON_PALMAS Say Y here to enable support for USB peripheral and USB host detection by palmas usb. +config EXTCON_QCOM_SPMI_MISC + tristate "Qualcomm USB extcon support" + help + Say Y here to enable SPMI PMIC based USB cable detection + support on Qualcomm PMICs such as PM8941. + config EXTCON_RT8973A tristate "Richtek RT8973A EXTCON support" depends on I2C diff --git a/drivers/extcon/Makefile b/drivers/extcon/Makefile index 972c813c375b..31a0a999c4fb 100644 --- a/drivers/extcon/Makefile +++ b/drivers/extcon/Makefile @@ -14,6 +14,7 @@ obj-$(CONFIG_EXTCON_MAX77693) += extcon-max77693.o obj-$(CONFIG_EXTCON_MAX77843) += extcon-max77843.o obj-$(CONFIG_EXTCON_MAX8997) += extcon-max8997.o obj-$(CONFIG_EXTCON_PALMAS) += extcon-palmas.o +obj-$(CONFIG_EXTCON_QCOM_SPMI_MISC) += extcon-qcom-spmi-misc.o obj-$(CONFIG_EXTCON_RT8973A) += extcon-rt8973a.o obj-$(CONFIG_EXTCON_SM5502) += extcon-sm5502.o obj-$(CONFIG_EXTCON_USB_GPIO) += extcon-usb-gpio.o diff --git a/drivers/extcon/extcon-qcom-spmi-misc.c b/drivers/extcon/extcon-qcom-spmi-misc.c new file mode 100644 index 000000000000..1b8e24494c60 --- /dev/null +++ b/drivers/extcon/extcon-qcom-spmi-misc.c @@ -0,0 +1,167 @@ +/** + * Based on extcon-usb-gpio.c + * + * Copyright (C) 2016 Linaro Ltd + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <linux/extcon.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/slab.h> +#include <linux/workqueue.h> + +#define USB_ID_DEBOUNCE_MS 5 /* ms */ + +struct qcom_usb_extcon_info { + struct extcon_dev *edev; + int irq; + struct delayed_work wq_detcable; + unsigned long debounce_jiffies; +}; + +static const unsigned int qcom_usb_extcon_cable[] = { + EXTCON_USB_HOST, + EXTCON_NONE, +}; + +static void qcom_usb_extcon_detect_cable(struct work_struct *work) +{ + bool id; + int ret; + struct qcom_usb_extcon_info *info = container_of(to_delayed_work(work), + struct qcom_usb_extcon_info, + wq_detcable); + + /* check ID and update cable state */ + ret = irq_get_irqchip_state(info->irq, IRQCHIP_STATE_LINE_LEVEL, &id); + if (ret) + return; + + extcon_set_cable_state_(info->edev, EXTCON_USB_HOST, !id); +} + +static irqreturn_t qcom_usb_irq_handler(int irq, void *dev_id) +{ + struct qcom_usb_extcon_info *info = dev_id; + + queue_delayed_work(system_power_efficient_wq, &info->wq_detcable, + info->debounce_jiffies); + + return IRQ_HANDLED; +} + +static int qcom_usb_extcon_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct qcom_usb_extcon_info *info; + int ret; + + info = devm_kzalloc(dev, sizeof(*info), GFP_KERNEL); + if (!info) + return -ENOMEM; + + info->edev = devm_extcon_dev_allocate(dev, qcom_usb_extcon_cable); + if (IS_ERR(info->edev)) { + dev_err(dev, "failed to allocate extcon device\n"); + return -ENOMEM; + } + + ret = devm_extcon_dev_register(dev, info->edev); + if (ret < 0) { + dev_err(dev, "failed to register extcon device\n"); + return ret; + } + + info->debounce_jiffies = msecs_to_jiffies(USB_ID_DEBOUNCE_MS); + INIT_DELAYED_WORK(&info->wq_detcable, qcom_usb_extcon_detect_cable); + + info->irq = platform_get_irq_byname(pdev, "usb_id"); + if (info->irq < 0) + return info->irq; + + ret = devm_request_threaded_irq(dev, info->irq, NULL, + qcom_usb_irq_handler, + IRQF_TRIGGER_RISING | + IRQF_TRIGGER_FALLING | IRQF_ONESHOT, + pdev->name, info); + if (ret < 0) { + dev_err(dev, "failed to request handler for ID IRQ\n"); + return ret; + } + + platform_set_drvdata(pdev, info); + device_init_wakeup(dev, 1); + + /* Perform initial detection */ + qcom_usb_extcon_detect_cable(&info->wq_detcable.work); + + return 0; +} + +static int qcom_usb_extcon_remove(struct platform_device *pdev) +{ + struct qcom_usb_extcon_info *info = platform_get_drvdata(pdev); + + cancel_delayed_work_sync(&info->wq_detcable); + + return 0; +} + +#ifdef CONFIG_PM_SLEEP +static int qcom_usb_extcon_suspend(struct device *dev) +{ + struct qcom_usb_extcon_info *info = dev_get_drvdata(dev); + int ret = 0; + + if (device_may_wakeup(dev)) + ret = enable_irq_wake(info->irq); + + return ret; +} + +static int qcom_usb_extcon_resume(struct device *dev) +{ + struct qcom_usb_extcon_info *info = dev_get_drvdata(dev); + int ret = 0; + + if (device_may_wakeup(dev)) + ret = disable_irq_wake(info->irq); + + return ret; +} +#endif + +static SIMPLE_DEV_PM_OPS(qcom_usb_extcon_pm_ops, + qcom_usb_extcon_suspend, qcom_usb_extcon_resume); + +static const struct of_device_id qcom_usb_extcon_dt_match[] = { + { .compatible = "qcom,pm8941-misc", }, + { } +}; +MODULE_DEVICE_TABLE(of, qcom_usb_extcon_dt_match); + +static struct platform_driver qcom_usb_extcon_driver = { + .probe = qcom_usb_extcon_probe, + .remove = qcom_usb_extcon_remove, + .driver = { + .name = "extcon-pm8941-misc", + .pm = &qcom_usb_extcon_pm_ops, + .of_match_table = qcom_usb_extcon_dt_match, + }, +}; +module_platform_driver(qcom_usb_extcon_driver); + +MODULE_DESCRIPTION("QCOM USB ID extcon driver"); +MODULE_LICENSE("GPL v2"); -- 2.9.0.rc2.8.ga28705d ^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH v2] extcon: Add support for qcom SPMI PMIC USB id detection hardware @ 2016-09-09 21:48 ` Stephen Boyd 0 siblings, 0 replies; 6+ messages in thread From: Stephen Boyd @ 2016-09-09 21:48 UTC (permalink / raw) To: linux-arm-kernel Some Qualcomm PMICs have a misc device that performs USB id pin detection via an interrupt. When the interrupt triggers, we should read the interrupt line to see if it has gone high or low. If the interrupt is low then the ID pin is grounded, and if the interrupt is high then the ID pin is being held high. Cc: Roger Quadros <rogerq@ti.com> Cc: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> --- Changes from v1: * Fixed Makefile ordering * Fixed up copyright markings .../bindings/extcon/qcom,pm8941-misc.txt | 41 +++++ drivers/extcon/Kconfig | 6 + drivers/extcon/Makefile | 1 + drivers/extcon/extcon-qcom-spmi-misc.c | 167 +++++++++++++++++++++ 4 files changed, 215 insertions(+) create mode 100644 Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt create mode 100644 drivers/extcon/extcon-qcom-spmi-misc.c diff --git a/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt b/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt new file mode 100644 index 000000000000..35383adb10f1 --- /dev/null +++ b/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt @@ -0,0 +1,41 @@ +Qualcomm's PM8941 USB ID Extcon device + +Some Qualcomm PMICs have a "misc" module that can be used to detect when +the USB ID pin has been pulled low or high. + +PROPERTIES + +- compatible: + Usage: required + Value type: <string> + Definition: Should contain "qcom,pm8941-misc"; + +- reg: + Usage: required + Value type: <u32> + Definition: Should contain the offset to the misc address space + +- interrupts: + Usage: required + Value type: <prop-encoded-array> + Definition: Should contain the usb id interrupt + +- interrupt-names: + Usage: required + Value type: <stringlist> + Definition: Should contain the string "usb_id" for the usb id interrupt + +Example: + + pmic { + usb_id: misc at 900 { + compatible = "qcom,pm8941-misc"; + reg = <0x900>; + interrupts = <0x0 0x9 0 IRQ_TYPE_EDGE_BOTH>; + interrupt-names = "usb_id"; + }; + } + + usb-controller { + extcon = <&usb_id>; + }; diff --git a/drivers/extcon/Kconfig b/drivers/extcon/Kconfig index 3d89e60a3e71..04788d92ea52 100644 --- a/drivers/extcon/Kconfig +++ b/drivers/extcon/Kconfig @@ -96,6 +96,12 @@ config EXTCON_PALMAS Say Y here to enable support for USB peripheral and USB host detection by palmas usb. +config EXTCON_QCOM_SPMI_MISC + tristate "Qualcomm USB extcon support" + help + Say Y here to enable SPMI PMIC based USB cable detection + support on Qualcomm PMICs such as PM8941. + config EXTCON_RT8973A tristate "Richtek RT8973A EXTCON support" depends on I2C diff --git a/drivers/extcon/Makefile b/drivers/extcon/Makefile index 972c813c375b..31a0a999c4fb 100644 --- a/drivers/extcon/Makefile +++ b/drivers/extcon/Makefile @@ -14,6 +14,7 @@ obj-$(CONFIG_EXTCON_MAX77693) += extcon-max77693.o obj-$(CONFIG_EXTCON_MAX77843) += extcon-max77843.o obj-$(CONFIG_EXTCON_MAX8997) += extcon-max8997.o obj-$(CONFIG_EXTCON_PALMAS) += extcon-palmas.o +obj-$(CONFIG_EXTCON_QCOM_SPMI_MISC) += extcon-qcom-spmi-misc.o obj-$(CONFIG_EXTCON_RT8973A) += extcon-rt8973a.o obj-$(CONFIG_EXTCON_SM5502) += extcon-sm5502.o obj-$(CONFIG_EXTCON_USB_GPIO) += extcon-usb-gpio.o diff --git a/drivers/extcon/extcon-qcom-spmi-misc.c b/drivers/extcon/extcon-qcom-spmi-misc.c new file mode 100644 index 000000000000..1b8e24494c60 --- /dev/null +++ b/drivers/extcon/extcon-qcom-spmi-misc.c @@ -0,0 +1,167 @@ +/** + * Based on extcon-usb-gpio.c + * + * Copyright (C) 2016 Linaro Ltd + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <linux/extcon.h> +#include <linux/init.h> +#include <linux/interrupt.h> +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/platform_device.h> +#include <linux/slab.h> +#include <linux/workqueue.h> + +#define USB_ID_DEBOUNCE_MS 5 /* ms */ + +struct qcom_usb_extcon_info { + struct extcon_dev *edev; + int irq; + struct delayed_work wq_detcable; + unsigned long debounce_jiffies; +}; + +static const unsigned int qcom_usb_extcon_cable[] = { + EXTCON_USB_HOST, + EXTCON_NONE, +}; + +static void qcom_usb_extcon_detect_cable(struct work_struct *work) +{ + bool id; + int ret; + struct qcom_usb_extcon_info *info = container_of(to_delayed_work(work), + struct qcom_usb_extcon_info, + wq_detcable); + + /* check ID and update cable state */ + ret = irq_get_irqchip_state(info->irq, IRQCHIP_STATE_LINE_LEVEL, &id); + if (ret) + return; + + extcon_set_cable_state_(info->edev, EXTCON_USB_HOST, !id); +} + +static irqreturn_t qcom_usb_irq_handler(int irq, void *dev_id) +{ + struct qcom_usb_extcon_info *info = dev_id; + + queue_delayed_work(system_power_efficient_wq, &info->wq_detcable, + info->debounce_jiffies); + + return IRQ_HANDLED; +} + +static int qcom_usb_extcon_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct qcom_usb_extcon_info *info; + int ret; + + info = devm_kzalloc(dev, sizeof(*info), GFP_KERNEL); + if (!info) + return -ENOMEM; + + info->edev = devm_extcon_dev_allocate(dev, qcom_usb_extcon_cable); + if (IS_ERR(info->edev)) { + dev_err(dev, "failed to allocate extcon device\n"); + return -ENOMEM; + } + + ret = devm_extcon_dev_register(dev, info->edev); + if (ret < 0) { + dev_err(dev, "failed to register extcon device\n"); + return ret; + } + + info->debounce_jiffies = msecs_to_jiffies(USB_ID_DEBOUNCE_MS); + INIT_DELAYED_WORK(&info->wq_detcable, qcom_usb_extcon_detect_cable); + + info->irq = platform_get_irq_byname(pdev, "usb_id"); + if (info->irq < 0) + return info->irq; + + ret = devm_request_threaded_irq(dev, info->irq, NULL, + qcom_usb_irq_handler, + IRQF_TRIGGER_RISING | + IRQF_TRIGGER_FALLING | IRQF_ONESHOT, + pdev->name, info); + if (ret < 0) { + dev_err(dev, "failed to request handler for ID IRQ\n"); + return ret; + } + + platform_set_drvdata(pdev, info); + device_init_wakeup(dev, 1); + + /* Perform initial detection */ + qcom_usb_extcon_detect_cable(&info->wq_detcable.work); + + return 0; +} + +static int qcom_usb_extcon_remove(struct platform_device *pdev) +{ + struct qcom_usb_extcon_info *info = platform_get_drvdata(pdev); + + cancel_delayed_work_sync(&info->wq_detcable); + + return 0; +} + +#ifdef CONFIG_PM_SLEEP +static int qcom_usb_extcon_suspend(struct device *dev) +{ + struct qcom_usb_extcon_info *info = dev_get_drvdata(dev); + int ret = 0; + + if (device_may_wakeup(dev)) + ret = enable_irq_wake(info->irq); + + return ret; +} + +static int qcom_usb_extcon_resume(struct device *dev) +{ + struct qcom_usb_extcon_info *info = dev_get_drvdata(dev); + int ret = 0; + + if (device_may_wakeup(dev)) + ret = disable_irq_wake(info->irq); + + return ret; +} +#endif + +static SIMPLE_DEV_PM_OPS(qcom_usb_extcon_pm_ops, + qcom_usb_extcon_suspend, qcom_usb_extcon_resume); + +static const struct of_device_id qcom_usb_extcon_dt_match[] = { + { .compatible = "qcom,pm8941-misc", }, + { } +}; +MODULE_DEVICE_TABLE(of, qcom_usb_extcon_dt_match); + +static struct platform_driver qcom_usb_extcon_driver = { + .probe = qcom_usb_extcon_probe, + .remove = qcom_usb_extcon_remove, + .driver = { + .name = "extcon-pm8941-misc", + .pm = &qcom_usb_extcon_pm_ops, + .of_match_table = qcom_usb_extcon_dt_match, + }, +}; +module_platform_driver(qcom_usb_extcon_driver); + +MODULE_DESCRIPTION("QCOM USB ID extcon driver"); +MODULE_LICENSE("GPL v2"); -- 2.9.0.rc2.8.ga28705d ^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH v2] extcon: Add support for qcom SPMI PMIC USB id detection hardware 2016-09-09 21:48 ` Stephen Boyd @ 2016-09-12 2:09 ` Chanwoo Choi -1 siblings, 0 replies; 6+ messages in thread From: Chanwoo Choi @ 2016-09-12 2:09 UTC (permalink / raw) To: Stephen Boyd; +Cc: linux-arm-kernel, linux-kernel, linux-arm-msm, Roger Quadros Hi Stephen, Looks good to me. But, there are something that need to be modified. - add the author information - add the description of driver - use the extcon_set_state() instead of extcon_set_cable_state_() I modified this patch and applied it because I should send the pull request within this week after releasing the rc6. I added the comment about the modification. On 2016년 09월 10일 06:48, Stephen Boyd wrote: > Some Qualcomm PMICs have a misc device that performs USB id pin > detection via an interrupt. When the interrupt triggers, we > should read the interrupt line to see if it has gone high or low. > If the interrupt is low then the ID pin is grounded, and if the > interrupt is high then the ID pin is being held high. > > Cc: Roger Quadros <rogerq@ti.com> > Cc: Chanwoo Choi <cw00.choi@samsung.com> > Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> > --- > > Changes from v1: > * Fixed Makefile ordering > * Fixed up copyright markings > > .../bindings/extcon/qcom,pm8941-misc.txt | 41 +++++ > drivers/extcon/Kconfig | 6 + > drivers/extcon/Makefile | 1 + > drivers/extcon/extcon-qcom-spmi-misc.c | 167 +++++++++++++++++++++ > 4 files changed, 215 insertions(+) > create mode 100644 Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt > create mode 100644 drivers/extcon/extcon-qcom-spmi-misc.c > > diff --git a/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt b/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt > new file mode 100644 > index 000000000000..35383adb10f1 > --- /dev/null > +++ b/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt > @@ -0,0 +1,41 @@ > +Qualcomm's PM8941 USB ID Extcon device > + > +Some Qualcomm PMICs have a "misc" module that can be used to detect when > +the USB ID pin has been pulled low or high. > + > +PROPERTIES > + > +- compatible: > + Usage: required > + Value type: <string> > + Definition: Should contain "qcom,pm8941-misc"; > + > +- reg: > + Usage: required > + Value type: <u32> > + Definition: Should contain the offset to the misc address space > + > +- interrupts: > + Usage: required > + Value type: <prop-encoded-array> > + Definition: Should contain the usb id interrupt > + > +- interrupt-names: > + Usage: required > + Value type: <stringlist> > + Definition: Should contain the string "usb_id" for the usb id interrupt > + > +Example: > + > + pmic { > + usb_id: misc@900 { > + compatible = "qcom,pm8941-misc"; > + reg = <0x900>; > + interrupts = <0x0 0x9 0 IRQ_TYPE_EDGE_BOTH>; > + interrupt-names = "usb_id"; > + }; > + } > + > + usb-controller { > + extcon = <&usb_id>; > + }; > diff --git a/drivers/extcon/Kconfig b/drivers/extcon/Kconfig > index 3d89e60a3e71..04788d92ea52 100644 > --- a/drivers/extcon/Kconfig > +++ b/drivers/extcon/Kconfig > @@ -96,6 +96,12 @@ config EXTCON_PALMAS > Say Y here to enable support for USB peripheral and USB host > detection by palmas usb. > > +config EXTCON_QCOM_SPMI_MISC > + tristate "Qualcomm USB extcon support" > + help > + Say Y here to enable SPMI PMIC based USB cable detection > + support on Qualcomm PMICs such as PM8941. > + > config EXTCON_RT8973A > tristate "Richtek RT8973A EXTCON support" > depends on I2C > diff --git a/drivers/extcon/Makefile b/drivers/extcon/Makefile > index 972c813c375b..31a0a999c4fb 100644 > --- a/drivers/extcon/Makefile > +++ b/drivers/extcon/Makefile > @@ -14,6 +14,7 @@ obj-$(CONFIG_EXTCON_MAX77693) += extcon-max77693.o > obj-$(CONFIG_EXTCON_MAX77843) += extcon-max77843.o > obj-$(CONFIG_EXTCON_MAX8997) += extcon-max8997.o > obj-$(CONFIG_EXTCON_PALMAS) += extcon-palmas.o > +obj-$(CONFIG_EXTCON_QCOM_SPMI_MISC) += extcon-qcom-spmi-misc.o > obj-$(CONFIG_EXTCON_RT8973A) += extcon-rt8973a.o > obj-$(CONFIG_EXTCON_SM5502) += extcon-sm5502.o > obj-$(CONFIG_EXTCON_USB_GPIO) += extcon-usb-gpio.o > diff --git a/drivers/extcon/extcon-qcom-spmi-misc.c b/drivers/extcon/extcon-qcom-spmi-misc.c > new file mode 100644 > index 000000000000..1b8e24494c60 > --- /dev/null > +++ b/drivers/extcon/extcon-qcom-spmi-misc.c > @@ -0,0 +1,167 @@ > +/** > + * Based on extcon-usb-gpio.c I think that following description is better than before. I'll modify it. * extcon-qcom-spmi-misc.c - Qualcomm USB extcon driver to support USB ID * detection based on extcon-usb-gpio.c. > + * > + * Copyright (C) 2016 Linaro Ltd s/Ltd/Ltd. You are missing the author information. I'll add following information: * Stephen Boyd <stephen.boyd@linaro.org> > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + * > + * This program is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + */ > + > +#include <linux/extcon.h> > +#include <linux/init.h> > +#include <linux/interrupt.h> > +#include <linux/kernel.h> > +#include <linux/module.h> > +#include <linux/platform_device.h> > +#include <linux/slab.h> > +#include <linux/workqueue.h> > + > +#define USB_ID_DEBOUNCE_MS 5 /* ms */ > + > +struct qcom_usb_extcon_info { > + struct extcon_dev *edev; > + int irq; > + struct delayed_work wq_detcable; > + unsigned long debounce_jiffies; > +}; > + > +static const unsigned int qcom_usb_extcon_cable[] = { > + EXTCON_USB_HOST, > + EXTCON_NONE, > +}; > + > +static void qcom_usb_extcon_detect_cable(struct work_struct *work) > +{ > + bool id; > + int ret; > + struct qcom_usb_extcon_info *info = container_of(to_delayed_work(work), > + struct qcom_usb_extcon_info, > + wq_detcable); > + > + /* check ID and update cable state */ > + ret = irq_get_irqchip_state(info->irq, IRQCHIP_STATE_LINE_LEVEL, &id); > + if (ret) > + return; > + > + extcon_set_cable_state_(info->edev, EXTCON_USB_HOST, !id); The extcon_set_cable_state_() is deprecated. Instead, I'll modify it using extcon_set_state() as following: extcon_set_state(info->edev, EXTCON_USB_HOST, !id); > +} > + > +static irqreturn_t qcom_usb_irq_handler(int irq, void *dev_id) > +{ > + struct qcom_usb_extcon_info *info = dev_id; > + > + queue_delayed_work(system_power_efficient_wq, &info->wq_detcable, > + info->debounce_jiffies); > + > + return IRQ_HANDLED; > +} > + > +static int qcom_usb_extcon_probe(struct platform_device *pdev) > +{ > + struct device *dev = &pdev->dev; > + struct qcom_usb_extcon_info *info; > + int ret; > + > + info = devm_kzalloc(dev, sizeof(*info), GFP_KERNEL); > + if (!info) > + return -ENOMEM; > + > + info->edev = devm_extcon_dev_allocate(dev, qcom_usb_extcon_cable); > + if (IS_ERR(info->edev)) { > + dev_err(dev, "failed to allocate extcon device\n"); > + return -ENOMEM; > + } > + > + ret = devm_extcon_dev_register(dev, info->edev); > + if (ret < 0) { > + dev_err(dev, "failed to register extcon device\n"); > + return ret; > + } > + > + info->debounce_jiffies = msecs_to_jiffies(USB_ID_DEBOUNCE_MS); > + INIT_DELAYED_WORK(&info->wq_detcable, qcom_usb_extcon_detect_cable); > + > + info->irq = platform_get_irq_byname(pdev, "usb_id"); > + if (info->irq < 0) > + return info->irq; > + > + ret = devm_request_threaded_irq(dev, info->irq, NULL, > + qcom_usb_irq_handler, > + IRQF_TRIGGER_RISING | > + IRQF_TRIGGER_FALLING | IRQF_ONESHOT, > + pdev->name, info); > + if (ret < 0) { > + dev_err(dev, "failed to request handler for ID IRQ\n"); > + return ret; > + } > + > + platform_set_drvdata(pdev, info); > + device_init_wakeup(dev, 1); > + > + /* Perform initial detection */ > + qcom_usb_extcon_detect_cable(&info->wq_detcable.work); > + > + return 0; > +} > + > +static int qcom_usb_extcon_remove(struct platform_device *pdev) > +{ > + struct qcom_usb_extcon_info *info = platform_get_drvdata(pdev); > + > + cancel_delayed_work_sync(&info->wq_detcable); > + > + return 0; > +} > + > +#ifdef CONFIG_PM_SLEEP > +static int qcom_usb_extcon_suspend(struct device *dev) > +{ > + struct qcom_usb_extcon_info *info = dev_get_drvdata(dev); > + int ret = 0; > + > + if (device_may_wakeup(dev)) > + ret = enable_irq_wake(info->irq); > + > + return ret; > +} > + > +static int qcom_usb_extcon_resume(struct device *dev) > +{ > + struct qcom_usb_extcon_info *info = dev_get_drvdata(dev); > + int ret = 0; > + > + if (device_may_wakeup(dev)) > + ret = disable_irq_wake(info->irq); > + > + return ret; > +} > +#endif > + > +static SIMPLE_DEV_PM_OPS(qcom_usb_extcon_pm_ops, > + qcom_usb_extcon_suspend, qcom_usb_extcon_resume); > + > +static const struct of_device_id qcom_usb_extcon_dt_match[] = { > + { .compatible = "qcom,pm8941-misc", }, > + { } > +}; > +MODULE_DEVICE_TABLE(of, qcom_usb_extcon_dt_match); > + > +static struct platform_driver qcom_usb_extcon_driver = { > + .probe = qcom_usb_extcon_probe, > + .remove = qcom_usb_extcon_remove, > + .driver = { > + .name = "extcon-pm8941-misc", > + .pm = &qcom_usb_extcon_pm_ops, > + .of_match_table = qcom_usb_extcon_dt_match, > + }, > +}; > +module_platform_driver(qcom_usb_extcon_driver); > + > +MODULE_DESCRIPTION("QCOM USB ID extcon driver"); You are missing the author information. I'll add it as following: MODULE_AUTHOR("Stephen Boyd <stephen.boyd@linaro.org>"); > +MODULE_LICENSE("GPL v2"); > -- Best Regards, Chanwoo Choi ^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH v2] extcon: Add support for qcom SPMI PMIC USB id detection hardware @ 2016-09-12 2:09 ` Chanwoo Choi 0 siblings, 0 replies; 6+ messages in thread From: Chanwoo Choi @ 2016-09-12 2:09 UTC (permalink / raw) To: linux-arm-kernel Hi Stephen, Looks good to me. But, there are something that need to be modified. - add the author information - add the description of driver - use the extcon_set_state() instead of extcon_set_cable_state_() I modified this patch and applied it because I should send the pull request within this week after releasing the rc6. I added the comment about the modification. On 2016? 09? 10? 06:48, Stephen Boyd wrote: > Some Qualcomm PMICs have a misc device that performs USB id pin > detection via an interrupt. When the interrupt triggers, we > should read the interrupt line to see if it has gone high or low. > If the interrupt is low then the ID pin is grounded, and if the > interrupt is high then the ID pin is being held high. > > Cc: Roger Quadros <rogerq@ti.com> > Cc: Chanwoo Choi <cw00.choi@samsung.com> > Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org> > --- > > Changes from v1: > * Fixed Makefile ordering > * Fixed up copyright markings > > .../bindings/extcon/qcom,pm8941-misc.txt | 41 +++++ > drivers/extcon/Kconfig | 6 + > drivers/extcon/Makefile | 1 + > drivers/extcon/extcon-qcom-spmi-misc.c | 167 +++++++++++++++++++++ > 4 files changed, 215 insertions(+) > create mode 100644 Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt > create mode 100644 drivers/extcon/extcon-qcom-spmi-misc.c > > diff --git a/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt b/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt > new file mode 100644 > index 000000000000..35383adb10f1 > --- /dev/null > +++ b/Documentation/devicetree/bindings/extcon/qcom,pm8941-misc.txt > @@ -0,0 +1,41 @@ > +Qualcomm's PM8941 USB ID Extcon device > + > +Some Qualcomm PMICs have a "misc" module that can be used to detect when > +the USB ID pin has been pulled low or high. > + > +PROPERTIES > + > +- compatible: > + Usage: required > + Value type: <string> > + Definition: Should contain "qcom,pm8941-misc"; > + > +- reg: > + Usage: required > + Value type: <u32> > + Definition: Should contain the offset to the misc address space > + > +- interrupts: > + Usage: required > + Value type: <prop-encoded-array> > + Definition: Should contain the usb id interrupt > + > +- interrupt-names: > + Usage: required > + Value type: <stringlist> > + Definition: Should contain the string "usb_id" for the usb id interrupt > + > +Example: > + > + pmic { > + usb_id: misc at 900 { > + compatible = "qcom,pm8941-misc"; > + reg = <0x900>; > + interrupts = <0x0 0x9 0 IRQ_TYPE_EDGE_BOTH>; > + interrupt-names = "usb_id"; > + }; > + } > + > + usb-controller { > + extcon = <&usb_id>; > + }; > diff --git a/drivers/extcon/Kconfig b/drivers/extcon/Kconfig > index 3d89e60a3e71..04788d92ea52 100644 > --- a/drivers/extcon/Kconfig > +++ b/drivers/extcon/Kconfig > @@ -96,6 +96,12 @@ config EXTCON_PALMAS > Say Y here to enable support for USB peripheral and USB host > detection by palmas usb. > > +config EXTCON_QCOM_SPMI_MISC > + tristate "Qualcomm USB extcon support" > + help > + Say Y here to enable SPMI PMIC based USB cable detection > + support on Qualcomm PMICs such as PM8941. > + > config EXTCON_RT8973A > tristate "Richtek RT8973A EXTCON support" > depends on I2C > diff --git a/drivers/extcon/Makefile b/drivers/extcon/Makefile > index 972c813c375b..31a0a999c4fb 100644 > --- a/drivers/extcon/Makefile > +++ b/drivers/extcon/Makefile > @@ -14,6 +14,7 @@ obj-$(CONFIG_EXTCON_MAX77693) += extcon-max77693.o > obj-$(CONFIG_EXTCON_MAX77843) += extcon-max77843.o > obj-$(CONFIG_EXTCON_MAX8997) += extcon-max8997.o > obj-$(CONFIG_EXTCON_PALMAS) += extcon-palmas.o > +obj-$(CONFIG_EXTCON_QCOM_SPMI_MISC) += extcon-qcom-spmi-misc.o > obj-$(CONFIG_EXTCON_RT8973A) += extcon-rt8973a.o > obj-$(CONFIG_EXTCON_SM5502) += extcon-sm5502.o > obj-$(CONFIG_EXTCON_USB_GPIO) += extcon-usb-gpio.o > diff --git a/drivers/extcon/extcon-qcom-spmi-misc.c b/drivers/extcon/extcon-qcom-spmi-misc.c > new file mode 100644 > index 000000000000..1b8e24494c60 > --- /dev/null > +++ b/drivers/extcon/extcon-qcom-spmi-misc.c > @@ -0,0 +1,167 @@ > +/** > + * Based on extcon-usb-gpio.c I think that following description is better than before. I'll modify it. * extcon-qcom-spmi-misc.c - Qualcomm USB extcon driver to support USB ID * detection based on extcon-usb-gpio.c. > + * > + * Copyright (C) 2016 Linaro Ltd s/Ltd/Ltd. You are missing the author information. I'll add following information: * Stephen Boyd <stephen.boyd@linaro.org> > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + * > + * This program is distributed in the hope that it will be useful, > + * but WITHOUT ANY WARRANTY; without even the implied warranty of > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the > + * GNU General Public License for more details. > + */ > + > +#include <linux/extcon.h> > +#include <linux/init.h> > +#include <linux/interrupt.h> > +#include <linux/kernel.h> > +#include <linux/module.h> > +#include <linux/platform_device.h> > +#include <linux/slab.h> > +#include <linux/workqueue.h> > + > +#define USB_ID_DEBOUNCE_MS 5 /* ms */ > + > +struct qcom_usb_extcon_info { > + struct extcon_dev *edev; > + int irq; > + struct delayed_work wq_detcable; > + unsigned long debounce_jiffies; > +}; > + > +static const unsigned int qcom_usb_extcon_cable[] = { > + EXTCON_USB_HOST, > + EXTCON_NONE, > +}; > + > +static void qcom_usb_extcon_detect_cable(struct work_struct *work) > +{ > + bool id; > + int ret; > + struct qcom_usb_extcon_info *info = container_of(to_delayed_work(work), > + struct qcom_usb_extcon_info, > + wq_detcable); > + > + /* check ID and update cable state */ > + ret = irq_get_irqchip_state(info->irq, IRQCHIP_STATE_LINE_LEVEL, &id); > + if (ret) > + return; > + > + extcon_set_cable_state_(info->edev, EXTCON_USB_HOST, !id); The extcon_set_cable_state_() is deprecated. Instead, I'll modify it using extcon_set_state() as following: extcon_set_state(info->edev, EXTCON_USB_HOST, !id); > +} > + > +static irqreturn_t qcom_usb_irq_handler(int irq, void *dev_id) > +{ > + struct qcom_usb_extcon_info *info = dev_id; > + > + queue_delayed_work(system_power_efficient_wq, &info->wq_detcable, > + info->debounce_jiffies); > + > + return IRQ_HANDLED; > +} > + > +static int qcom_usb_extcon_probe(struct platform_device *pdev) > +{ > + struct device *dev = &pdev->dev; > + struct qcom_usb_extcon_info *info; > + int ret; > + > + info = devm_kzalloc(dev, sizeof(*info), GFP_KERNEL); > + if (!info) > + return -ENOMEM; > + > + info->edev = devm_extcon_dev_allocate(dev, qcom_usb_extcon_cable); > + if (IS_ERR(info->edev)) { > + dev_err(dev, "failed to allocate extcon device\n"); > + return -ENOMEM; > + } > + > + ret = devm_extcon_dev_register(dev, info->edev); > + if (ret < 0) { > + dev_err(dev, "failed to register extcon device\n"); > + return ret; > + } > + > + info->debounce_jiffies = msecs_to_jiffies(USB_ID_DEBOUNCE_MS); > + INIT_DELAYED_WORK(&info->wq_detcable, qcom_usb_extcon_detect_cable); > + > + info->irq = platform_get_irq_byname(pdev, "usb_id"); > + if (info->irq < 0) > + return info->irq; > + > + ret = devm_request_threaded_irq(dev, info->irq, NULL, > + qcom_usb_irq_handler, > + IRQF_TRIGGER_RISING | > + IRQF_TRIGGER_FALLING | IRQF_ONESHOT, > + pdev->name, info); > + if (ret < 0) { > + dev_err(dev, "failed to request handler for ID IRQ\n"); > + return ret; > + } > + > + platform_set_drvdata(pdev, info); > + device_init_wakeup(dev, 1); > + > + /* Perform initial detection */ > + qcom_usb_extcon_detect_cable(&info->wq_detcable.work); > + > + return 0; > +} > + > +static int qcom_usb_extcon_remove(struct platform_device *pdev) > +{ > + struct qcom_usb_extcon_info *info = platform_get_drvdata(pdev); > + > + cancel_delayed_work_sync(&info->wq_detcable); > + > + return 0; > +} > + > +#ifdef CONFIG_PM_SLEEP > +static int qcom_usb_extcon_suspend(struct device *dev) > +{ > + struct qcom_usb_extcon_info *info = dev_get_drvdata(dev); > + int ret = 0; > + > + if (device_may_wakeup(dev)) > + ret = enable_irq_wake(info->irq); > + > + return ret; > +} > + > +static int qcom_usb_extcon_resume(struct device *dev) > +{ > + struct qcom_usb_extcon_info *info = dev_get_drvdata(dev); > + int ret = 0; > + > + if (device_may_wakeup(dev)) > + ret = disable_irq_wake(info->irq); > + > + return ret; > +} > +#endif > + > +static SIMPLE_DEV_PM_OPS(qcom_usb_extcon_pm_ops, > + qcom_usb_extcon_suspend, qcom_usb_extcon_resume); > + > +static const struct of_device_id qcom_usb_extcon_dt_match[] = { > + { .compatible = "qcom,pm8941-misc", }, > + { } > +}; > +MODULE_DEVICE_TABLE(of, qcom_usb_extcon_dt_match); > + > +static struct platform_driver qcom_usb_extcon_driver = { > + .probe = qcom_usb_extcon_probe, > + .remove = qcom_usb_extcon_remove, > + .driver = { > + .name = "extcon-pm8941-misc", > + .pm = &qcom_usb_extcon_pm_ops, > + .of_match_table = qcom_usb_extcon_dt_match, > + }, > +}; > +module_platform_driver(qcom_usb_extcon_driver); > + > +MODULE_DESCRIPTION("QCOM USB ID extcon driver"); You are missing the author information. I'll add it as following: MODULE_AUTHOR("Stephen Boyd <stephen.boyd@linaro.org>"); > +MODULE_LICENSE("GPL v2"); > -- Best Regards, Chanwoo Choi ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH v2] extcon: Add support for qcom SPMI PMIC USB id detection hardware 2016-09-12 2:09 ` Chanwoo Choi @ 2016-09-12 19:24 ` Stephen Boyd -1 siblings, 0 replies; 6+ messages in thread From: Stephen Boyd @ 2016-09-12 19:24 UTC (permalink / raw) To: Chanwoo Choi; +Cc: linux-arm-msm, linux-kernel, linux-arm-kernel, Roger Quadros Quoting Chanwoo Choi (2016-09-11 19:09:26) > Hi Stephen, > > Looks good to me. > But, there are something that need to be modified. > - add the author information > - add the description of driver > - use the extcon_set_state() instead of extcon_set_cable_state_() > > I modified this patch and applied it because I should send > the pull request within this week after releasing the rc6. > > I added the comment about the modification. > Ok, sounds good. Thanks. ^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH v2] extcon: Add support for qcom SPMI PMIC USB id detection hardware @ 2016-09-12 19:24 ` Stephen Boyd 0 siblings, 0 replies; 6+ messages in thread From: Stephen Boyd @ 2016-09-12 19:24 UTC (permalink / raw) To: linux-arm-kernel Quoting Chanwoo Choi (2016-09-11 19:09:26) > Hi Stephen, > > Looks good to me. > But, there are something that need to be modified. > - add the author information > - add the description of driver > - use the extcon_set_state() instead of extcon_set_cable_state_() > > I modified this patch and applied it because I should send > the pull request within this week after releasing the rc6. > > I added the comment about the modification. > Ok, sounds good. Thanks. ^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2016-09-12 19:24 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <CGME20160909214851epcas1p3718ae2ac8b9758b2d81e581ab88bf2ce@epcas1p3.samsung.com>
2016-09-09 21:48 ` [PATCH v2] extcon: Add support for qcom SPMI PMIC USB id detection hardware Stephen Boyd
2016-09-09 21:48 ` Stephen Boyd
2016-09-12 2:09 ` Chanwoo Choi
2016-09-12 2:09 ` Chanwoo Choi
2016-09-12 19:24 ` Stephen Boyd
2016-09-12 19:24 ` Stephen Boyd
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.