* [PATCH v8 1/3] usb: chipidea: Configure phy for appropriate mode
2017-01-25 22:32 ` Stephen Boyd
(?)
@ 2017-01-25 22:32 ` Stephen Boyd
-1 siblings, 0 replies; 17+ messages in thread
From: Stephen Boyd @ 2017-01-25 22:32 UTC (permalink / raw)
To: Peter Chen
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-arm-msm-u79uwXL29TY76Z2rM5mHXA,
linux-usb-u79uwXL29TY76Z2rM5mHXA, Andy Gross, Bjorn Andersson,
Neil Armstrong, Arnd Bergmann, Felipe Balbi,
Kishon Vijay Abraham I, Greg Kroah-Hartman
When the qcom chipidea controller is used with an extcon, we need
to signal device mode or host mode to the phy so it can configure
itself for the correct mode. This should be done after the phy is
powered up, so that the register writes work correctly. Add in
the appropriate phy_set_mode() call here.
Cc: Peter Chen <peter.chen-3arQi8VN3Tc@public.gmane.org>
Cc: Greg Kroah-Hartman <gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r@public.gmane.org>
Signed-off-by: Stephen Boyd <stephen.boyd-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
drivers/usb/chipidea/core.c | 20 ++++++++++++++------
1 file changed, 14 insertions(+), 6 deletions(-)
diff --git a/drivers/usb/chipidea/core.c b/drivers/usb/chipidea/core.c
index 802ca253cf6d..fc3b9e07aa81 100644
--- a/drivers/usb/chipidea/core.c
+++ b/drivers/usb/chipidea/core.c
@@ -428,13 +428,21 @@ void ci_platform_configure(struct ci_hdrc *ci)
is_device_mode = hw_read(ci, OP_USBMODE, USBMODE_CM) == USBMODE_CM_DC;
is_host_mode = hw_read(ci, OP_USBMODE, USBMODE_CM) == USBMODE_CM_HC;
- if (is_device_mode &&
- (ci->platdata->flags & CI_HDRC_DISABLE_DEVICE_STREAMING))
- hw_write(ci, OP_USBMODE, USBMODE_CI_SDIS, USBMODE_CI_SDIS);
+ if (is_device_mode) {
+ phy_set_mode(ci->phy, PHY_MODE_USB_DEVICE);
- if (is_host_mode &&
- (ci->platdata->flags & CI_HDRC_DISABLE_HOST_STREAMING))
- hw_write(ci, OP_USBMODE, USBMODE_CI_SDIS, USBMODE_CI_SDIS);
+ if (ci->platdata->flags & CI_HDRC_DISABLE_DEVICE_STREAMING)
+ hw_write(ci, OP_USBMODE, USBMODE_CI_SDIS,
+ USBMODE_CI_SDIS);
+ }
+
+ if (is_host_mode) {
+ phy_set_mode(ci->phy, PHY_MODE_USB_HOST);
+
+ if (ci->platdata->flags & CI_HDRC_DISABLE_HOST_STREAMING)
+ hw_write(ci, OP_USBMODE, USBMODE_CI_SDIS,
+ USBMODE_CI_SDIS);
+ }
if (ci->platdata->flags & CI_HDRC_FORCE_FULLSPEED) {
if (ci->hw_bank.lpm)
--
2.10.0.297.gf6727b0
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 17+ messages in thread* [PATCH v8 1/3] usb: chipidea: Configure phy for appropriate mode
@ 2017-01-25 22:32 ` Stephen Boyd
0 siblings, 0 replies; 17+ messages in thread
From: Stephen Boyd @ 2017-01-25 22:32 UTC (permalink / raw)
To: Peter Chen
Cc: linux-arm-kernel, linux-kernel, linux-arm-msm, linux-usb,
Andy Gross, Bjorn Andersson, Neil Armstrong, Arnd Bergmann,
Felipe Balbi, Kishon Vijay Abraham I, Greg Kroah-Hartman
When the qcom chipidea controller is used with an extcon, we need
to signal device mode or host mode to the phy so it can configure
itself for the correct mode. This should be done after the phy is
powered up, so that the register writes work correctly. Add in
the appropriate phy_set_mode() call here.
Cc: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
---
drivers/usb/chipidea/core.c | 20 ++++++++++++++------
1 file changed, 14 insertions(+), 6 deletions(-)
diff --git a/drivers/usb/chipidea/core.c b/drivers/usb/chipidea/core.c
index 802ca253cf6d..fc3b9e07aa81 100644
--- a/drivers/usb/chipidea/core.c
+++ b/drivers/usb/chipidea/core.c
@@ -428,13 +428,21 @@ void ci_platform_configure(struct ci_hdrc *ci)
is_device_mode = hw_read(ci, OP_USBMODE, USBMODE_CM) == USBMODE_CM_DC;
is_host_mode = hw_read(ci, OP_USBMODE, USBMODE_CM) == USBMODE_CM_HC;
- if (is_device_mode &&
- (ci->platdata->flags & CI_HDRC_DISABLE_DEVICE_STREAMING))
- hw_write(ci, OP_USBMODE, USBMODE_CI_SDIS, USBMODE_CI_SDIS);
+ if (is_device_mode) {
+ phy_set_mode(ci->phy, PHY_MODE_USB_DEVICE);
- if (is_host_mode &&
- (ci->platdata->flags & CI_HDRC_DISABLE_HOST_STREAMING))
- hw_write(ci, OP_USBMODE, USBMODE_CI_SDIS, USBMODE_CI_SDIS);
+ if (ci->platdata->flags & CI_HDRC_DISABLE_DEVICE_STREAMING)
+ hw_write(ci, OP_USBMODE, USBMODE_CI_SDIS,
+ USBMODE_CI_SDIS);
+ }
+
+ if (is_host_mode) {
+ phy_set_mode(ci->phy, PHY_MODE_USB_HOST);
+
+ if (ci->platdata->flags & CI_HDRC_DISABLE_HOST_STREAMING)
+ hw_write(ci, OP_USBMODE, USBMODE_CI_SDIS,
+ USBMODE_CI_SDIS);
+ }
if (ci->platdata->flags & CI_HDRC_FORCE_FULLSPEED) {
if (ci->hw_bank.lpm)
--
2.10.0.297.gf6727b0
^ permalink raw reply related [flat|nested] 17+ messages in thread* [PATCH v8 1/3] usb: chipidea: Configure phy for appropriate mode
@ 2017-01-25 22:32 ` Stephen Boyd
0 siblings, 0 replies; 17+ messages in thread
From: Stephen Boyd @ 2017-01-25 22:32 UTC (permalink / raw)
To: linux-arm-kernel
When the qcom chipidea controller is used with an extcon, we need
to signal device mode or host mode to the phy so it can configure
itself for the correct mode. This should be done after the phy is
powered up, so that the register writes work correctly. Add in
the appropriate phy_set_mode() call here.
Cc: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
---
drivers/usb/chipidea/core.c | 20 ++++++++++++++------
1 file changed, 14 insertions(+), 6 deletions(-)
diff --git a/drivers/usb/chipidea/core.c b/drivers/usb/chipidea/core.c
index 802ca253cf6d..fc3b9e07aa81 100644
--- a/drivers/usb/chipidea/core.c
+++ b/drivers/usb/chipidea/core.c
@@ -428,13 +428,21 @@ void ci_platform_configure(struct ci_hdrc *ci)
is_device_mode = hw_read(ci, OP_USBMODE, USBMODE_CM) == USBMODE_CM_DC;
is_host_mode = hw_read(ci, OP_USBMODE, USBMODE_CM) == USBMODE_CM_HC;
- if (is_device_mode &&
- (ci->platdata->flags & CI_HDRC_DISABLE_DEVICE_STREAMING))
- hw_write(ci, OP_USBMODE, USBMODE_CI_SDIS, USBMODE_CI_SDIS);
+ if (is_device_mode) {
+ phy_set_mode(ci->phy, PHY_MODE_USB_DEVICE);
- if (is_host_mode &&
- (ci->platdata->flags & CI_HDRC_DISABLE_HOST_STREAMING))
- hw_write(ci, OP_USBMODE, USBMODE_CI_SDIS, USBMODE_CI_SDIS);
+ if (ci->platdata->flags & CI_HDRC_DISABLE_DEVICE_STREAMING)
+ hw_write(ci, OP_USBMODE, USBMODE_CI_SDIS,
+ USBMODE_CI_SDIS);
+ }
+
+ if (is_host_mode) {
+ phy_set_mode(ci->phy, PHY_MODE_USB_HOST);
+
+ if (ci->platdata->flags & CI_HDRC_DISABLE_HOST_STREAMING)
+ hw_write(ci, OP_USBMODE, USBMODE_CI_SDIS,
+ USBMODE_CI_SDIS);
+ }
if (ci->platdata->flags & CI_HDRC_FORCE_FULLSPEED) {
if (ci->hw_bank.lpm)
--
2.10.0.297.gf6727b0
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PATCH v8 2/3] phy: Add support for Qualcomm's USB HSIC phy
2017-01-25 22:32 ` Stephen Boyd
(?)
@ 2017-01-25 22:32 ` Stephen Boyd
-1 siblings, 0 replies; 17+ messages in thread
From: Stephen Boyd @ 2017-01-25 22:32 UTC (permalink / raw)
To: Kishon Vijay Abraham I
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-arm-msm-u79uwXL29TY76Z2rM5mHXA,
linux-usb-u79uwXL29TY76Z2rM5mHXA, Andy Gross, Bjorn Andersson,
Neil Armstrong, Arnd Bergmann, Felipe Balbi, Peter Chen,
devicetree-u79uwXL29TY76Z2rM5mHXA
The HSIC USB controller on qcom SoCs has an integrated all
digital phy controlled via the ULPI viewport.
Cc: Kishon Vijay Abraham I <kishon-l0cyMroinI0@public.gmane.org>
Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
Cc: <devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org>
Signed-off-by: Stephen Boyd <stephen.boyd-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
.../devicetree/bindings/phy/qcom,usb-hsic-phy.txt | 65 +++++++++
drivers/phy/Kconfig | 7 +
drivers/phy/Makefile | 1 +
drivers/phy/phy-qcom-usb-hsic.c | 160 +++++++++++++++++++++
4 files changed, 233 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/qcom,usb-hsic-phy.txt
create mode 100644 drivers/phy/phy-qcom-usb-hsic.c
diff --git a/Documentation/devicetree/bindings/phy/qcom,usb-hsic-phy.txt b/Documentation/devicetree/bindings/phy/qcom,usb-hsic-phy.txt
new file mode 100644
index 000000000000..3c7cb2be4b12
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/qcom,usb-hsic-phy.txt
@@ -0,0 +1,65 @@
+Qualcomm's USB HSIC PHY
+
+PROPERTIES
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: Should contain "qcom,usb-hsic-phy" and more specifically one of the
+ following:
+
+ "qcom,usb-hsic-phy-mdm9615"
+ "qcom,usb-hsic-phy-msm8974"
+
+- #phy-cells:
+ Usage: required
+ Value type: <u32>
+ Definition: Should contain 0
+
+- clocks:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: Should contain clock specifier for phy, calibration and
+ a calibration sleep clock
+
+- clock-names:
+ Usage: required
+ Value type: <stringlist>
+ Definition: Should contain "phy, "cal" and "cal_sleep"
+
+- pinctrl-names:
+ Usage: required
+ Value type: <stringlist>
+ Definition: Should contain "init" and "default" in that order
+
+- pinctrl-0:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: List of pinctrl settings to apply to keep HSIC pins in a glitch
+ free state
+
+- pinctrl-1:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: List of pinctrl settings to apply to mux out the HSIC pins
+
+EXAMPLE
+
+usb-controller {
+ ulpi {
+ phy {
+ compatible = "qcom,usb-hsic-phy-msm8974",
+ "qcom,usb-hsic-phy";
+ #phy-cells = <0>;
+ pinctrl-names = "init", "default";
+ pinctrl-0 = <&hsic_sleep>;
+ pinctrl-1 = <&hsic_default>;
+ clocks = <&gcc GCC_USB_HSIC_CLK>,
+ <&gcc GCC_USB_HSIC_IO_CAL_CLK>,
+ <&gcc GCC_USB_HSIC_IO_CAL_SLEEP_CLK>;
+ clock-names = "phy", "cal", "cal_sleep";
+ assigned-clocks = <&gcc GCC_USB_HSIC_IO_CAL_CLK>;
+ assigned-clock-rates = <960000>;
+ };
+ };
+};
diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index e8eb7f225a88..a430a64981d5 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -437,6 +437,13 @@ config PHY_QCOM_UFS
help
Support for UFS PHY on QCOM chipsets.
+config PHY_QCOM_USB_HSIC
+ tristate "Qualcomm USB HSIC ULPI PHY module"
+ depends on USB_ULPI_BUS
+ select GENERIC_PHY
+ help
+ Support for the USB HSIC ULPI compliant PHY on QCOM chipsets.
+
config PHY_TUSB1210
tristate "TI TUSB1210 ULPI PHY module"
depends on USB_ULPI_BUS
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index 65eb2f436a41..c43c9df5d301 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -52,6 +52,7 @@ obj-$(CONFIG_PHY_STIH407_USB) += phy-stih407-usb.o
obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs.o
obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs-qmp-20nm.o
obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs-qmp-14nm.o
+obj-$(CONFIG_PHY_QCOM_USB_HSIC) += phy-qcom-usb-hsic.o
obj-$(CONFIG_PHY_TUSB1210) += phy-tusb1210.o
obj-$(CONFIG_PHY_BRCM_SATA) += phy-brcm-sata.o
obj-$(CONFIG_PHY_PISTACHIO_USB) += phy-pistachio-usb.o
diff --git a/drivers/phy/phy-qcom-usb-hsic.c b/drivers/phy/phy-qcom-usb-hsic.c
new file mode 100644
index 000000000000..47690f9945b9
--- /dev/null
+++ b/drivers/phy/phy-qcom-usb-hsic.c
@@ -0,0 +1,160 @@
+/**
+ * Copyright (C) 2016 Linaro Ltd
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/module.h>
+#include <linux/ulpi/driver.h>
+#include <linux/ulpi/regs.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/pinctrl/pinctrl-state.h>
+#include <linux/delay.h>
+#include <linux/clk.h>
+
+#include "ulpi_phy.h"
+
+#define ULPI_HSIC_CFG 0x30
+#define ULPI_HSIC_IO_CAL 0x33
+
+struct qcom_usb_hsic_phy {
+ struct ulpi *ulpi;
+ struct phy *phy;
+ struct pinctrl *pctl;
+ struct clk *phy_clk;
+ struct clk *cal_clk;
+ struct clk *cal_sleep_clk;
+};
+
+static int qcom_usb_hsic_phy_power_on(struct phy *phy)
+{
+ struct qcom_usb_hsic_phy *uphy = phy_get_drvdata(phy);
+ struct ulpi *ulpi = uphy->ulpi;
+ struct pinctrl_state *pins_default;
+ int ret;
+
+ ret = clk_prepare_enable(uphy->phy_clk);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(uphy->cal_clk);
+ if (ret)
+ goto err_cal;
+
+ ret = clk_prepare_enable(uphy->cal_sleep_clk);
+ if (ret)
+ goto err_sleep;
+
+ /* Set periodic calibration interval to ~2.048sec in HSIC_IO_CAL_REG */
+ ret = ulpi_write(ulpi, ULPI_HSIC_IO_CAL, 0xff);
+ if (ret)
+ goto err_ulpi;
+
+ /* Enable periodic IO calibration in HSIC_CFG register */
+ ret = ulpi_write(ulpi, ULPI_HSIC_CFG, 0xa8);
+ if (ret)
+ goto err_ulpi;
+
+ /* Configure pins for HSIC functionality */
+ pins_default = pinctrl_lookup_state(uphy->pctl, PINCTRL_STATE_DEFAULT);
+ if (IS_ERR(pins_default))
+ return PTR_ERR(pins_default);
+
+ ret = pinctrl_select_state(uphy->pctl, pins_default);
+ if (ret)
+ goto err_ulpi;
+
+ /* Enable HSIC mode in HSIC_CFG register */
+ ret = ulpi_write(ulpi, ULPI_SET(ULPI_HSIC_CFG), 0x01);
+ if (ret)
+ goto err_ulpi;
+
+ /* Disable auto-resume */
+ ret = ulpi_write(ulpi, ULPI_CLR(ULPI_IFC_CTRL),
+ ULPI_IFC_CTRL_AUTORESUME);
+ if (ret)
+ goto err_ulpi;
+
+ return ret;
+err_ulpi:
+ clk_disable_unprepare(uphy->cal_sleep_clk);
+err_sleep:
+ clk_disable_unprepare(uphy->cal_clk);
+err_cal:
+ clk_disable_unprepare(uphy->phy_clk);
+ return ret;
+}
+
+static int qcom_usb_hsic_phy_power_off(struct phy *phy)
+{
+ struct qcom_usb_hsic_phy *uphy = phy_get_drvdata(phy);
+
+ clk_disable_unprepare(uphy->cal_sleep_clk);
+ clk_disable_unprepare(uphy->cal_clk);
+ clk_disable_unprepare(uphy->phy_clk);
+
+ return 0;
+}
+
+static const struct phy_ops qcom_usb_hsic_phy_ops = {
+ .power_on = qcom_usb_hsic_phy_power_on,
+ .power_off = qcom_usb_hsic_phy_power_off,
+ .owner = THIS_MODULE,
+};
+
+static int qcom_usb_hsic_phy_probe(struct ulpi *ulpi)
+{
+ struct qcom_usb_hsic_phy *uphy;
+ struct phy_provider *p;
+ struct clk *clk;
+
+ uphy = devm_kzalloc(&ulpi->dev, sizeof(*uphy), GFP_KERNEL);
+ if (!uphy)
+ return -ENOMEM;
+ ulpi_set_drvdata(ulpi, uphy);
+
+ uphy->ulpi = ulpi;
+ uphy->pctl = devm_pinctrl_get(&ulpi->dev);
+ if (IS_ERR(uphy->pctl))
+ return PTR_ERR(uphy->pctl);
+
+ uphy->phy_clk = clk = devm_clk_get(&ulpi->dev, "phy");
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ uphy->cal_clk = clk = devm_clk_get(&ulpi->dev, "cal");
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ uphy->cal_sleep_clk = clk = devm_clk_get(&ulpi->dev, "cal_sleep");
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ uphy->phy = devm_phy_create(&ulpi->dev, ulpi->dev.of_node,
+ &qcom_usb_hsic_phy_ops);
+ if (IS_ERR(uphy->phy))
+ return PTR_ERR(uphy->phy);
+ phy_set_drvdata(uphy->phy, uphy);
+
+ p = devm_of_phy_provider_register(&ulpi->dev, of_phy_simple_xlate);
+ return PTR_ERR_OR_ZERO(p);
+}
+
+static const struct of_device_id qcom_usb_hsic_phy_match[] = {
+ { .compatible = "qcom,usb-hsic-phy", },
+ { }
+};
+MODULE_DEVICE_TABLE(of, qcom_usb_hsic_phy_match);
+
+static struct ulpi_driver qcom_usb_hsic_phy_driver = {
+ .probe = qcom_usb_hsic_phy_probe,
+ .driver = {
+ .name = "qcom_usb_hsic_phy",
+ .of_match_table = qcom_usb_hsic_phy_match,
+ },
+};
+module_ulpi_driver(qcom_usb_hsic_phy_driver);
+
+MODULE_DESCRIPTION("Qualcomm USB HSIC phy");
+MODULE_LICENSE("GPL v2");
--
2.10.0.297.gf6727b0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 17+ messages in thread* [PATCH v8 2/3] phy: Add support for Qualcomm's USB HSIC phy
@ 2017-01-25 22:32 ` Stephen Boyd
0 siblings, 0 replies; 17+ messages in thread
From: Stephen Boyd @ 2017-01-25 22:32 UTC (permalink / raw)
To: Kishon Vijay Abraham I
Cc: linux-arm-kernel, linux-kernel, linux-arm-msm, linux-usb,
Andy Gross, Bjorn Andersson, Neil Armstrong, Arnd Bergmann,
Felipe Balbi, Peter Chen, devicetree
The HSIC USB controller on qcom SoCs has an integrated all
digital phy controlled via the ULPI viewport.
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
---
.../devicetree/bindings/phy/qcom,usb-hsic-phy.txt | 65 +++++++++
drivers/phy/Kconfig | 7 +
drivers/phy/Makefile | 1 +
drivers/phy/phy-qcom-usb-hsic.c | 160 +++++++++++++++++++++
4 files changed, 233 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/qcom,usb-hsic-phy.txt
create mode 100644 drivers/phy/phy-qcom-usb-hsic.c
diff --git a/Documentation/devicetree/bindings/phy/qcom,usb-hsic-phy.txt b/Documentation/devicetree/bindings/phy/qcom,usb-hsic-phy.txt
new file mode 100644
index 000000000000..3c7cb2be4b12
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/qcom,usb-hsic-phy.txt
@@ -0,0 +1,65 @@
+Qualcomm's USB HSIC PHY
+
+PROPERTIES
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: Should contain "qcom,usb-hsic-phy" and more specifically one of the
+ following:
+
+ "qcom,usb-hsic-phy-mdm9615"
+ "qcom,usb-hsic-phy-msm8974"
+
+- #phy-cells:
+ Usage: required
+ Value type: <u32>
+ Definition: Should contain 0
+
+- clocks:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: Should contain clock specifier for phy, calibration and
+ a calibration sleep clock
+
+- clock-names:
+ Usage: required
+ Value type: <stringlist>
+ Definition: Should contain "phy, "cal" and "cal_sleep"
+
+- pinctrl-names:
+ Usage: required
+ Value type: <stringlist>
+ Definition: Should contain "init" and "default" in that order
+
+- pinctrl-0:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: List of pinctrl settings to apply to keep HSIC pins in a glitch
+ free state
+
+- pinctrl-1:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: List of pinctrl settings to apply to mux out the HSIC pins
+
+EXAMPLE
+
+usb-controller {
+ ulpi {
+ phy {
+ compatible = "qcom,usb-hsic-phy-msm8974",
+ "qcom,usb-hsic-phy";
+ #phy-cells = <0>;
+ pinctrl-names = "init", "default";
+ pinctrl-0 = <&hsic_sleep>;
+ pinctrl-1 = <&hsic_default>;
+ clocks = <&gcc GCC_USB_HSIC_CLK>,
+ <&gcc GCC_USB_HSIC_IO_CAL_CLK>,
+ <&gcc GCC_USB_HSIC_IO_CAL_SLEEP_CLK>;
+ clock-names = "phy", "cal", "cal_sleep";
+ assigned-clocks = <&gcc GCC_USB_HSIC_IO_CAL_CLK>;
+ assigned-clock-rates = <960000>;
+ };
+ };
+};
diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index e8eb7f225a88..a430a64981d5 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -437,6 +437,13 @@ config PHY_QCOM_UFS
help
Support for UFS PHY on QCOM chipsets.
+config PHY_QCOM_USB_HSIC
+ tristate "Qualcomm USB HSIC ULPI PHY module"
+ depends on USB_ULPI_BUS
+ select GENERIC_PHY
+ help
+ Support for the USB HSIC ULPI compliant PHY on QCOM chipsets.
+
config PHY_TUSB1210
tristate "TI TUSB1210 ULPI PHY module"
depends on USB_ULPI_BUS
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index 65eb2f436a41..c43c9df5d301 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -52,6 +52,7 @@ obj-$(CONFIG_PHY_STIH407_USB) += phy-stih407-usb.o
obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs.o
obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs-qmp-20nm.o
obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs-qmp-14nm.o
+obj-$(CONFIG_PHY_QCOM_USB_HSIC) += phy-qcom-usb-hsic.o
obj-$(CONFIG_PHY_TUSB1210) += phy-tusb1210.o
obj-$(CONFIG_PHY_BRCM_SATA) += phy-brcm-sata.o
obj-$(CONFIG_PHY_PISTACHIO_USB) += phy-pistachio-usb.o
diff --git a/drivers/phy/phy-qcom-usb-hsic.c b/drivers/phy/phy-qcom-usb-hsic.c
new file mode 100644
index 000000000000..47690f9945b9
--- /dev/null
+++ b/drivers/phy/phy-qcom-usb-hsic.c
@@ -0,0 +1,160 @@
+/**
+ * Copyright (C) 2016 Linaro Ltd
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/module.h>
+#include <linux/ulpi/driver.h>
+#include <linux/ulpi/regs.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/pinctrl/pinctrl-state.h>
+#include <linux/delay.h>
+#include <linux/clk.h>
+
+#include "ulpi_phy.h"
+
+#define ULPI_HSIC_CFG 0x30
+#define ULPI_HSIC_IO_CAL 0x33
+
+struct qcom_usb_hsic_phy {
+ struct ulpi *ulpi;
+ struct phy *phy;
+ struct pinctrl *pctl;
+ struct clk *phy_clk;
+ struct clk *cal_clk;
+ struct clk *cal_sleep_clk;
+};
+
+static int qcom_usb_hsic_phy_power_on(struct phy *phy)
+{
+ struct qcom_usb_hsic_phy *uphy = phy_get_drvdata(phy);
+ struct ulpi *ulpi = uphy->ulpi;
+ struct pinctrl_state *pins_default;
+ int ret;
+
+ ret = clk_prepare_enable(uphy->phy_clk);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(uphy->cal_clk);
+ if (ret)
+ goto err_cal;
+
+ ret = clk_prepare_enable(uphy->cal_sleep_clk);
+ if (ret)
+ goto err_sleep;
+
+ /* Set periodic calibration interval to ~2.048sec in HSIC_IO_CAL_REG */
+ ret = ulpi_write(ulpi, ULPI_HSIC_IO_CAL, 0xff);
+ if (ret)
+ goto err_ulpi;
+
+ /* Enable periodic IO calibration in HSIC_CFG register */
+ ret = ulpi_write(ulpi, ULPI_HSIC_CFG, 0xa8);
+ if (ret)
+ goto err_ulpi;
+
+ /* Configure pins for HSIC functionality */
+ pins_default = pinctrl_lookup_state(uphy->pctl, PINCTRL_STATE_DEFAULT);
+ if (IS_ERR(pins_default))
+ return PTR_ERR(pins_default);
+
+ ret = pinctrl_select_state(uphy->pctl, pins_default);
+ if (ret)
+ goto err_ulpi;
+
+ /* Enable HSIC mode in HSIC_CFG register */
+ ret = ulpi_write(ulpi, ULPI_SET(ULPI_HSIC_CFG), 0x01);
+ if (ret)
+ goto err_ulpi;
+
+ /* Disable auto-resume */
+ ret = ulpi_write(ulpi, ULPI_CLR(ULPI_IFC_CTRL),
+ ULPI_IFC_CTRL_AUTORESUME);
+ if (ret)
+ goto err_ulpi;
+
+ return ret;
+err_ulpi:
+ clk_disable_unprepare(uphy->cal_sleep_clk);
+err_sleep:
+ clk_disable_unprepare(uphy->cal_clk);
+err_cal:
+ clk_disable_unprepare(uphy->phy_clk);
+ return ret;
+}
+
+static int qcom_usb_hsic_phy_power_off(struct phy *phy)
+{
+ struct qcom_usb_hsic_phy *uphy = phy_get_drvdata(phy);
+
+ clk_disable_unprepare(uphy->cal_sleep_clk);
+ clk_disable_unprepare(uphy->cal_clk);
+ clk_disable_unprepare(uphy->phy_clk);
+
+ return 0;
+}
+
+static const struct phy_ops qcom_usb_hsic_phy_ops = {
+ .power_on = qcom_usb_hsic_phy_power_on,
+ .power_off = qcom_usb_hsic_phy_power_off,
+ .owner = THIS_MODULE,
+};
+
+static int qcom_usb_hsic_phy_probe(struct ulpi *ulpi)
+{
+ struct qcom_usb_hsic_phy *uphy;
+ struct phy_provider *p;
+ struct clk *clk;
+
+ uphy = devm_kzalloc(&ulpi->dev, sizeof(*uphy), GFP_KERNEL);
+ if (!uphy)
+ return -ENOMEM;
+ ulpi_set_drvdata(ulpi, uphy);
+
+ uphy->ulpi = ulpi;
+ uphy->pctl = devm_pinctrl_get(&ulpi->dev);
+ if (IS_ERR(uphy->pctl))
+ return PTR_ERR(uphy->pctl);
+
+ uphy->phy_clk = clk = devm_clk_get(&ulpi->dev, "phy");
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ uphy->cal_clk = clk = devm_clk_get(&ulpi->dev, "cal");
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ uphy->cal_sleep_clk = clk = devm_clk_get(&ulpi->dev, "cal_sleep");
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ uphy->phy = devm_phy_create(&ulpi->dev, ulpi->dev.of_node,
+ &qcom_usb_hsic_phy_ops);
+ if (IS_ERR(uphy->phy))
+ return PTR_ERR(uphy->phy);
+ phy_set_drvdata(uphy->phy, uphy);
+
+ p = devm_of_phy_provider_register(&ulpi->dev, of_phy_simple_xlate);
+ return PTR_ERR_OR_ZERO(p);
+}
+
+static const struct of_device_id qcom_usb_hsic_phy_match[] = {
+ { .compatible = "qcom,usb-hsic-phy", },
+ { }
+};
+MODULE_DEVICE_TABLE(of, qcom_usb_hsic_phy_match);
+
+static struct ulpi_driver qcom_usb_hsic_phy_driver = {
+ .probe = qcom_usb_hsic_phy_probe,
+ .driver = {
+ .name = "qcom_usb_hsic_phy",
+ .of_match_table = qcom_usb_hsic_phy_match,
+ },
+};
+module_ulpi_driver(qcom_usb_hsic_phy_driver);
+
+MODULE_DESCRIPTION("Qualcomm USB HSIC phy");
+MODULE_LICENSE("GPL v2");
--
2.10.0.297.gf6727b0
^ permalink raw reply related [flat|nested] 17+ messages in thread* [PATCH v8 2/3] phy: Add support for Qualcomm's USB HSIC phy
@ 2017-01-25 22:32 ` Stephen Boyd
0 siblings, 0 replies; 17+ messages in thread
From: Stephen Boyd @ 2017-01-25 22:32 UTC (permalink / raw)
To: linux-arm-kernel
The HSIC USB controller on qcom SoCs has an integrated all
digital phy controlled via the ULPI viewport.
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
---
.../devicetree/bindings/phy/qcom,usb-hsic-phy.txt | 65 +++++++++
drivers/phy/Kconfig | 7 +
drivers/phy/Makefile | 1 +
drivers/phy/phy-qcom-usb-hsic.c | 160 +++++++++++++++++++++
4 files changed, 233 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/qcom,usb-hsic-phy.txt
create mode 100644 drivers/phy/phy-qcom-usb-hsic.c
diff --git a/Documentation/devicetree/bindings/phy/qcom,usb-hsic-phy.txt b/Documentation/devicetree/bindings/phy/qcom,usb-hsic-phy.txt
new file mode 100644
index 000000000000..3c7cb2be4b12
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/qcom,usb-hsic-phy.txt
@@ -0,0 +1,65 @@
+Qualcomm's USB HSIC PHY
+
+PROPERTIES
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: Should contain "qcom,usb-hsic-phy" and more specifically one of the
+ following:
+
+ "qcom,usb-hsic-phy-mdm9615"
+ "qcom,usb-hsic-phy-msm8974"
+
+- #phy-cells:
+ Usage: required
+ Value type: <u32>
+ Definition: Should contain 0
+
+- clocks:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: Should contain clock specifier for phy, calibration and
+ a calibration sleep clock
+
+- clock-names:
+ Usage: required
+ Value type: <stringlist>
+ Definition: Should contain "phy, "cal" and "cal_sleep"
+
+- pinctrl-names:
+ Usage: required
+ Value type: <stringlist>
+ Definition: Should contain "init" and "default" in that order
+
+- pinctrl-0:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: List of pinctrl settings to apply to keep HSIC pins in a glitch
+ free state
+
+- pinctrl-1:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: List of pinctrl settings to apply to mux out the HSIC pins
+
+EXAMPLE
+
+usb-controller {
+ ulpi {
+ phy {
+ compatible = "qcom,usb-hsic-phy-msm8974",
+ "qcom,usb-hsic-phy";
+ #phy-cells = <0>;
+ pinctrl-names = "init", "default";
+ pinctrl-0 = <&hsic_sleep>;
+ pinctrl-1 = <&hsic_default>;
+ clocks = <&gcc GCC_USB_HSIC_CLK>,
+ <&gcc GCC_USB_HSIC_IO_CAL_CLK>,
+ <&gcc GCC_USB_HSIC_IO_CAL_SLEEP_CLK>;
+ clock-names = "phy", "cal", "cal_sleep";
+ assigned-clocks = <&gcc GCC_USB_HSIC_IO_CAL_CLK>;
+ assigned-clock-rates = <960000>;
+ };
+ };
+};
diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index e8eb7f225a88..a430a64981d5 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -437,6 +437,13 @@ config PHY_QCOM_UFS
help
Support for UFS PHY on QCOM chipsets.
+config PHY_QCOM_USB_HSIC
+ tristate "Qualcomm USB HSIC ULPI PHY module"
+ depends on USB_ULPI_BUS
+ select GENERIC_PHY
+ help
+ Support for the USB HSIC ULPI compliant PHY on QCOM chipsets.
+
config PHY_TUSB1210
tristate "TI TUSB1210 ULPI PHY module"
depends on USB_ULPI_BUS
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index 65eb2f436a41..c43c9df5d301 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -52,6 +52,7 @@ obj-$(CONFIG_PHY_STIH407_USB) += phy-stih407-usb.o
obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs.o
obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs-qmp-20nm.o
obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs-qmp-14nm.o
+obj-$(CONFIG_PHY_QCOM_USB_HSIC) += phy-qcom-usb-hsic.o
obj-$(CONFIG_PHY_TUSB1210) += phy-tusb1210.o
obj-$(CONFIG_PHY_BRCM_SATA) += phy-brcm-sata.o
obj-$(CONFIG_PHY_PISTACHIO_USB) += phy-pistachio-usb.o
diff --git a/drivers/phy/phy-qcom-usb-hsic.c b/drivers/phy/phy-qcom-usb-hsic.c
new file mode 100644
index 000000000000..47690f9945b9
--- /dev/null
+++ b/drivers/phy/phy-qcom-usb-hsic.c
@@ -0,0 +1,160 @@
+/**
+ * Copyright (C) 2016 Linaro Ltd
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/module.h>
+#include <linux/ulpi/driver.h>
+#include <linux/ulpi/regs.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/pinctrl/pinctrl-state.h>
+#include <linux/delay.h>
+#include <linux/clk.h>
+
+#include "ulpi_phy.h"
+
+#define ULPI_HSIC_CFG 0x30
+#define ULPI_HSIC_IO_CAL 0x33
+
+struct qcom_usb_hsic_phy {
+ struct ulpi *ulpi;
+ struct phy *phy;
+ struct pinctrl *pctl;
+ struct clk *phy_clk;
+ struct clk *cal_clk;
+ struct clk *cal_sleep_clk;
+};
+
+static int qcom_usb_hsic_phy_power_on(struct phy *phy)
+{
+ struct qcom_usb_hsic_phy *uphy = phy_get_drvdata(phy);
+ struct ulpi *ulpi = uphy->ulpi;
+ struct pinctrl_state *pins_default;
+ int ret;
+
+ ret = clk_prepare_enable(uphy->phy_clk);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(uphy->cal_clk);
+ if (ret)
+ goto err_cal;
+
+ ret = clk_prepare_enable(uphy->cal_sleep_clk);
+ if (ret)
+ goto err_sleep;
+
+ /* Set periodic calibration interval to ~2.048sec in HSIC_IO_CAL_REG */
+ ret = ulpi_write(ulpi, ULPI_HSIC_IO_CAL, 0xff);
+ if (ret)
+ goto err_ulpi;
+
+ /* Enable periodic IO calibration in HSIC_CFG register */
+ ret = ulpi_write(ulpi, ULPI_HSIC_CFG, 0xa8);
+ if (ret)
+ goto err_ulpi;
+
+ /* Configure pins for HSIC functionality */
+ pins_default = pinctrl_lookup_state(uphy->pctl, PINCTRL_STATE_DEFAULT);
+ if (IS_ERR(pins_default))
+ return PTR_ERR(pins_default);
+
+ ret = pinctrl_select_state(uphy->pctl, pins_default);
+ if (ret)
+ goto err_ulpi;
+
+ /* Enable HSIC mode in HSIC_CFG register */
+ ret = ulpi_write(ulpi, ULPI_SET(ULPI_HSIC_CFG), 0x01);
+ if (ret)
+ goto err_ulpi;
+
+ /* Disable auto-resume */
+ ret = ulpi_write(ulpi, ULPI_CLR(ULPI_IFC_CTRL),
+ ULPI_IFC_CTRL_AUTORESUME);
+ if (ret)
+ goto err_ulpi;
+
+ return ret;
+err_ulpi:
+ clk_disable_unprepare(uphy->cal_sleep_clk);
+err_sleep:
+ clk_disable_unprepare(uphy->cal_clk);
+err_cal:
+ clk_disable_unprepare(uphy->phy_clk);
+ return ret;
+}
+
+static int qcom_usb_hsic_phy_power_off(struct phy *phy)
+{
+ struct qcom_usb_hsic_phy *uphy = phy_get_drvdata(phy);
+
+ clk_disable_unprepare(uphy->cal_sleep_clk);
+ clk_disable_unprepare(uphy->cal_clk);
+ clk_disable_unprepare(uphy->phy_clk);
+
+ return 0;
+}
+
+static const struct phy_ops qcom_usb_hsic_phy_ops = {
+ .power_on = qcom_usb_hsic_phy_power_on,
+ .power_off = qcom_usb_hsic_phy_power_off,
+ .owner = THIS_MODULE,
+};
+
+static int qcom_usb_hsic_phy_probe(struct ulpi *ulpi)
+{
+ struct qcom_usb_hsic_phy *uphy;
+ struct phy_provider *p;
+ struct clk *clk;
+
+ uphy = devm_kzalloc(&ulpi->dev, sizeof(*uphy), GFP_KERNEL);
+ if (!uphy)
+ return -ENOMEM;
+ ulpi_set_drvdata(ulpi, uphy);
+
+ uphy->ulpi = ulpi;
+ uphy->pctl = devm_pinctrl_get(&ulpi->dev);
+ if (IS_ERR(uphy->pctl))
+ return PTR_ERR(uphy->pctl);
+
+ uphy->phy_clk = clk = devm_clk_get(&ulpi->dev, "phy");
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ uphy->cal_clk = clk = devm_clk_get(&ulpi->dev, "cal");
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ uphy->cal_sleep_clk = clk = devm_clk_get(&ulpi->dev, "cal_sleep");
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ uphy->phy = devm_phy_create(&ulpi->dev, ulpi->dev.of_node,
+ &qcom_usb_hsic_phy_ops);
+ if (IS_ERR(uphy->phy))
+ return PTR_ERR(uphy->phy);
+ phy_set_drvdata(uphy->phy, uphy);
+
+ p = devm_of_phy_provider_register(&ulpi->dev, of_phy_simple_xlate);
+ return PTR_ERR_OR_ZERO(p);
+}
+
+static const struct of_device_id qcom_usb_hsic_phy_match[] = {
+ { .compatible = "qcom,usb-hsic-phy", },
+ { }
+};
+MODULE_DEVICE_TABLE(of, qcom_usb_hsic_phy_match);
+
+static struct ulpi_driver qcom_usb_hsic_phy_driver = {
+ .probe = qcom_usb_hsic_phy_probe,
+ .driver = {
+ .name = "qcom_usb_hsic_phy",
+ .of_match_table = qcom_usb_hsic_phy_match,
+ },
+};
+module_ulpi_driver(qcom_usb_hsic_phy_driver);
+
+MODULE_DESCRIPTION("Qualcomm USB HSIC phy");
+MODULE_LICENSE("GPL v2");
--
2.10.0.297.gf6727b0
^ permalink raw reply related [flat|nested] 17+ messages in thread
* [PATCH v8 3/3] phy: Add support for Qualcomm's USB HS phy
2017-01-25 22:32 ` Stephen Boyd
(?)
@ 2017-01-25 22:32 ` Stephen Boyd
-1 siblings, 0 replies; 17+ messages in thread
From: Stephen Boyd @ 2017-01-25 22:32 UTC (permalink / raw)
To: Kishon Vijay Abraham I
Cc: linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-arm-msm-u79uwXL29TY76Z2rM5mHXA,
linux-usb-u79uwXL29TY76Z2rM5mHXA, Andy Gross, Bjorn Andersson,
Neil Armstrong, Arnd Bergmann, Felipe Balbi, Peter Chen,
devicetree-u79uwXL29TY76Z2rM5mHXA
The high-speed phy on qcom SoCs is controlled via the ULPI
viewport.
Cc: Kishon Vijay Abraham I <kishon-l0cyMroinI0@public.gmane.org>
Cc: <devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org>
Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
Signed-off-by: Stephen Boyd <stephen.boyd-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
---
.../devicetree/bindings/phy/qcom,usb-hs-phy.txt | 84 ++++++
drivers/phy/Kconfig | 8 +
drivers/phy/Makefile | 1 +
drivers/phy/phy-qcom-usb-hs.c | 296 +++++++++++++++++++++
4 files changed, 389 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.txt
create mode 100644 drivers/phy/phy-qcom-usb-hs.c
diff --git a/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.txt b/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.txt
new file mode 100644
index 000000000000..b3b75c1e6285
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.txt
@@ -0,0 +1,84 @@
+Qualcomm's USB HS PHY
+
+PROPERTIES
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: Should contain "qcom,usb-hs-phy" and more specifically one of the
+ following:
+
+ "qcom,usb-hs-phy-apq8064"
+ "qcom,usb-hs-phy-msm8916"
+ "qcom,usb-hs-phy-msm8974"
+
+- #phy-cells:
+ Usage: required
+ Value type: <u32>
+ Definition: Should contain 0
+
+- clocks:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: Should contain clock specifier for the reference and sleep
+ clocks
+
+- clock-names:
+ Usage: required
+ Value type: <stringlist>
+ Definition: Should contain "ref" and "sleep" for the reference and sleep
+ clocks respectively
+
+- resets:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: Should contain the phy and POR resets
+
+- reset-names:
+ Usage: required
+ Value type: <stringlist>
+ Definition: Should contain "phy" and "por" for the phy and POR resets
+ respectively
+
+- v3p3-supply:
+ Usage: required
+ Value type: <phandle>
+ Definition: Should contain a reference to the 3.3V supply
+
+- v1p8-supply:
+ Usage: required
+ Value type: <phandle>
+ Definition: Should contain a reference to the 1.8V supply
+
+- extcon:
+ Usage: optional
+ Value type: <prop-encoded-array>
+ Definition: Should contain the vbus extcon
+
+- qcom,init-seq:
+ Usage: optional
+ Value type: <u8 array>
+ Definition: Should contain a sequence of ULPI address and value pairs to
+ program into the ULPI_EXT_VENDOR_SPECIFIC area. This is related
+ to Device Mode Eye Diagram test. The addresses are offsets
+ from the ULPI_EXT_VENDOR_SPECIFIC address, for example,
+ <0x1 0x53> would mean "write the value 0x53 to address 0x81".
+
+EXAMPLE
+
+otg: usb-controller {
+ ulpi {
+ phy {
+ compatible = "qcom,usb-hs-phy-msm8974", "qcom,usb-hs-phy";
+ #phy-cells = <0>;
+ clocks = <&xo_board>, <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
+ clock-names = "ref", "sleep";
+ resets = <&gcc GCC_USB2A_PHY_BCR>, <&otg 0>;
+ reset-names = "phy", "por";
+ v3p3-supply = <&pm8941_l24>;
+ v1p8-supply = <&pm8941_l6>;
+ extcon = <&smbb>;
+ qcom,init-seq = /bits/ 8 <0x1 0x63>;
+ };
+ };
+};
diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index a430a64981d5..61a22e985831 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -437,6 +437,14 @@ config PHY_QCOM_UFS
help
Support for UFS PHY on QCOM chipsets.
+config PHY_QCOM_USB_HS
+ tristate "Qualcomm USB HS PHY module"
+ depends on USB_ULPI_BUS
+ select GENERIC_PHY
+ help
+ Support for the USB high-speed ULPI compliant phy on Qualcomm
+ chipsets.
+
config PHY_QCOM_USB_HSIC
tristate "Qualcomm USB HSIC ULPI PHY module"
depends on USB_ULPI_BUS
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index c43c9df5d301..0e4259473d28 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -52,6 +52,7 @@ obj-$(CONFIG_PHY_STIH407_USB) += phy-stih407-usb.o
obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs.o
obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs-qmp-20nm.o
obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs-qmp-14nm.o
+obj-$(CONFIG_PHY_QCOM_USB_HS) += phy-qcom-usb-hs.o
obj-$(CONFIG_PHY_QCOM_USB_HSIC) += phy-qcom-usb-hsic.o
obj-$(CONFIG_PHY_TUSB1210) += phy-tusb1210.o
obj-$(CONFIG_PHY_BRCM_SATA) += phy-brcm-sata.o
diff --git a/drivers/phy/phy-qcom-usb-hs.c b/drivers/phy/phy-qcom-usb-hs.c
new file mode 100644
index 000000000000..94dfbfd739c3
--- /dev/null
+++ b/drivers/phy/phy-qcom-usb-hs.c
@@ -0,0 +1,296 @@
+/**
+ * Copyright (C) 2016 Linaro Ltd
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/module.h>
+#include <linux/ulpi/driver.h>
+#include <linux/ulpi/regs.h>
+#include <linux/clk.h>
+#include <linux/regulator/consumer.h>
+#include <linux/of_device.h>
+#include <linux/reset.h>
+#include <linux/extcon.h>
+#include <linux/notifier.h>
+
+#include "ulpi_phy.h"
+
+#define ULPI_PWR_CLK_MNG_REG 0x88
+# define ULPI_PWR_OTG_COMP_DISABLE BIT(0)
+
+#define ULPI_MISC_A 0x96
+# define ULPI_MISC_A_VBUSVLDEXTSEL BIT(1)
+# define ULPI_MISC_A_VBUSVLDEXT BIT(0)
+
+
+struct ulpi_seq {
+ u8 addr;
+ u8 val;
+};
+
+struct qcom_usb_hs_phy {
+ struct ulpi *ulpi;
+ struct phy *phy;
+ struct clk *ref_clk;
+ struct clk *sleep_clk;
+ struct regulator *v1p8;
+ struct regulator *v3p3;
+ struct reset_control *reset;
+ struct ulpi_seq *init_seq;
+ struct extcon_dev *vbus_edev;
+ struct notifier_block vbus_notify;
+};
+
+static int qcom_usb_hs_phy_set_mode(struct phy *phy, enum phy_mode mode)
+{
+ struct qcom_usb_hs_phy *uphy = phy_get_drvdata(phy);
+ u8 addr;
+ int ret;
+
+ if (!uphy->vbus_edev) {
+ u8 val = 0;
+
+ switch (mode) {
+ case PHY_MODE_USB_OTG:
+ case PHY_MODE_USB_HOST:
+ val |= ULPI_INT_IDGRD;
+ case PHY_MODE_USB_DEVICE:
+ val |= ULPI_INT_SESS_VALID;
+ default:
+ break;
+ }
+
+ ret = ulpi_write(uphy->ulpi, ULPI_USB_INT_EN_RISE, val);
+ if (ret)
+ return ret;
+ ret = ulpi_write(uphy->ulpi, ULPI_USB_INT_EN_FALL, val);
+ } else {
+ switch (mode) {
+ case PHY_MODE_USB_OTG:
+ case PHY_MODE_USB_DEVICE:
+ addr = ULPI_SET(ULPI_MISC_A);
+ break;
+ case PHY_MODE_USB_HOST:
+ addr = ULPI_CLR(ULPI_MISC_A);
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ ret = ulpi_write(uphy->ulpi, ULPI_SET(ULPI_PWR_CLK_MNG_REG),
+ ULPI_PWR_OTG_COMP_DISABLE);
+ if (ret)
+ return ret;
+ ret = ulpi_write(uphy->ulpi, addr, ULPI_MISC_A_VBUSVLDEXTSEL);
+ }
+
+ return ret;
+}
+
+static int
+qcom_usb_hs_phy_vbus_notifier(struct notifier_block *nb, unsigned long event,
+ void *ptr)
+{
+ struct qcom_usb_hs_phy *uphy;
+ u8 addr;
+
+ uphy = container_of(nb, struct qcom_usb_hs_phy, vbus_notify);
+
+ if (event)
+ addr = ULPI_SET(ULPI_MISC_A);
+ else
+ addr = ULPI_CLR(ULPI_MISC_A);
+
+ return ulpi_write(uphy->ulpi, addr, ULPI_MISC_A_VBUSVLDEXT);
+}
+
+static int qcom_usb_hs_phy_power_on(struct phy *phy)
+{
+ struct qcom_usb_hs_phy *uphy = phy_get_drvdata(phy);
+ struct ulpi *ulpi = uphy->ulpi;
+ const struct ulpi_seq *seq;
+ int ret, state;
+
+ ret = clk_prepare_enable(uphy->ref_clk);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(uphy->sleep_clk);
+ if (ret)
+ goto err_sleep;
+
+ ret = regulator_set_load(uphy->v1p8, 50000);
+ if (ret < 0)
+ goto err_1p8;
+
+ ret = regulator_enable(uphy->v1p8);
+ if (ret)
+ goto err_1p8;
+
+ ret = regulator_set_voltage_triplet(uphy->v3p3, 3050000, 3300000,
+ 3300000);
+ if (ret)
+ goto err_3p3;
+
+ ret = regulator_set_load(uphy->v3p3, 50000);
+ if (ret < 0)
+ goto err_3p3;
+
+ ret = regulator_enable(uphy->v3p3);
+ if (ret)
+ goto err_3p3;
+
+ for (seq = uphy->init_seq; seq->addr; seq++) {
+ ret = ulpi_write(ulpi, ULPI_EXT_VENDOR_SPECIFIC + seq->addr,
+ seq->val);
+ if (ret)
+ goto err_ulpi;
+ }
+
+ if (uphy->reset) {
+ ret = reset_control_reset(uphy->reset);
+ if (ret)
+ goto err_ulpi;
+ }
+
+ if (uphy->vbus_edev) {
+ state = extcon_get_cable_state_(uphy->vbus_edev, EXTCON_USB);
+ /* setup initial state */
+ qcom_usb_hs_phy_vbus_notifier(&uphy->vbus_notify, state,
+ uphy->vbus_edev);
+ ret = extcon_register_notifier(uphy->vbus_edev, EXTCON_USB,
+ &uphy->vbus_notify);
+ if (ret)
+ goto err_ulpi;
+ }
+
+ return 0;
+err_ulpi:
+ regulator_disable(uphy->v3p3);
+err_3p3:
+ regulator_disable(uphy->v1p8);
+err_1p8:
+ clk_disable_unprepare(uphy->sleep_clk);
+err_sleep:
+ clk_disable_unprepare(uphy->ref_clk);
+ return ret;
+}
+
+static int qcom_usb_hs_phy_power_off(struct phy *phy)
+{
+ int ret;
+ struct qcom_usb_hs_phy *uphy = phy_get_drvdata(phy);
+
+ if (uphy->vbus_edev) {
+ ret = extcon_unregister_notifier(uphy->vbus_edev, EXTCON_USB,
+ &uphy->vbus_notify);
+ if (ret)
+ return ret;
+ }
+
+ regulator_disable(uphy->v3p3);
+ regulator_disable(uphy->v1p8);
+ clk_disable_unprepare(uphy->sleep_clk);
+ clk_disable_unprepare(uphy->ref_clk);
+
+ return 0;
+}
+
+static const struct phy_ops qcom_usb_hs_phy_ops = {
+ .power_on = qcom_usb_hs_phy_power_on,
+ .power_off = qcom_usb_hs_phy_power_off,
+ .set_mode = qcom_usb_hs_phy_set_mode,
+ .owner = THIS_MODULE,
+};
+
+static int qcom_usb_hs_phy_probe(struct ulpi *ulpi)
+{
+ struct qcom_usb_hs_phy *uphy;
+ struct phy_provider *p;
+ struct clk *clk;
+ struct regulator *reg;
+ struct reset_control *reset;
+ int size;
+ int ret;
+
+ uphy = devm_kzalloc(&ulpi->dev, sizeof(*uphy), GFP_KERNEL);
+ if (!uphy)
+ return -ENOMEM;
+ ulpi_set_drvdata(ulpi, uphy);
+ uphy->ulpi = ulpi;
+
+ size = of_property_count_u8_elems(ulpi->dev.of_node, "qcom,init-seq");
+ if (size < 0)
+ size = 0;
+ uphy->init_seq = devm_kmalloc_array(&ulpi->dev, (size / 2) + 1,
+ sizeof(*uphy->init_seq), GFP_KERNEL);
+ if (!uphy->init_seq)
+ return -ENOMEM;
+ ret = of_property_read_u8_array(ulpi->dev.of_node, "qcom,init-seq",
+ (u8 *)uphy->init_seq, size);
+ if (ret && size)
+ return ret;
+ /* NUL terminate */
+ uphy->init_seq[size / 2].addr = uphy->init_seq[size / 2].val = 0;
+
+ uphy->ref_clk = clk = devm_clk_get(&ulpi->dev, "ref");
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ uphy->sleep_clk = clk = devm_clk_get(&ulpi->dev, "sleep");
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ uphy->v1p8 = reg = devm_regulator_get(&ulpi->dev, "v1p8");
+ if (IS_ERR(reg))
+ return PTR_ERR(reg);
+
+ uphy->v3p3 = reg = devm_regulator_get(&ulpi->dev, "v3p3");
+ if (IS_ERR(reg))
+ return PTR_ERR(reg);
+
+ uphy->reset = reset = devm_reset_control_get(&ulpi->dev, "por");
+ if (IS_ERR(reset)) {
+ if (PTR_ERR(reset) == -EPROBE_DEFER)
+ return PTR_ERR(reset);
+ uphy->reset = NULL;
+ }
+
+ uphy->phy = devm_phy_create(&ulpi->dev, ulpi->dev.of_node,
+ &qcom_usb_hs_phy_ops);
+ if (IS_ERR(uphy->phy))
+ return PTR_ERR(uphy->phy);
+
+ uphy->vbus_edev = extcon_get_edev_by_phandle(&ulpi->dev, 0);
+ if (IS_ERR(uphy->vbus_edev)) {
+ if (PTR_ERR(uphy->vbus_edev) != -ENODEV)
+ return PTR_ERR(uphy->vbus_edev);
+ uphy->vbus_edev = NULL;
+ }
+
+ uphy->vbus_notify.notifier_call = qcom_usb_hs_phy_vbus_notifier;
+ phy_set_drvdata(uphy->phy, uphy);
+
+ p = devm_of_phy_provider_register(&ulpi->dev, of_phy_simple_xlate);
+ return PTR_ERR_OR_ZERO(p);
+}
+
+static const struct of_device_id qcom_usb_hs_phy_match[] = {
+ { .compatible = "qcom,usb-hs-phy", },
+ { }
+};
+MODULE_DEVICE_TABLE(of, qcom_usb_hs_phy_match);
+
+static struct ulpi_driver qcom_usb_hs_phy_driver = {
+ .probe = qcom_usb_hs_phy_probe,
+ .driver = {
+ .name = "qcom_usb_hs_phy",
+ .of_match_table = qcom_usb_hs_phy_match,
+ },
+};
+module_ulpi_driver(qcom_usb_hs_phy_driver);
+
+MODULE_DESCRIPTION("Qualcomm USB HS phy");
+MODULE_LICENSE("GPL v2");
--
2.10.0.297.gf6727b0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 17+ messages in thread* [PATCH v8 3/3] phy: Add support for Qualcomm's USB HS phy
@ 2017-01-25 22:32 ` Stephen Boyd
0 siblings, 0 replies; 17+ messages in thread
From: Stephen Boyd @ 2017-01-25 22:32 UTC (permalink / raw)
To: Kishon Vijay Abraham I
Cc: linux-arm-kernel, linux-kernel, linux-arm-msm, linux-usb,
Andy Gross, Bjorn Andersson, Neil Armstrong, Arnd Bergmann,
Felipe Balbi, Peter Chen, devicetree
The high-speed phy on qcom SoCs is controlled via the ULPI
viewport.
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: <devicetree@vger.kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
---
.../devicetree/bindings/phy/qcom,usb-hs-phy.txt | 84 ++++++
drivers/phy/Kconfig | 8 +
drivers/phy/Makefile | 1 +
drivers/phy/phy-qcom-usb-hs.c | 296 +++++++++++++++++++++
4 files changed, 389 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.txt
create mode 100644 drivers/phy/phy-qcom-usb-hs.c
diff --git a/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.txt b/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.txt
new file mode 100644
index 000000000000..b3b75c1e6285
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.txt
@@ -0,0 +1,84 @@
+Qualcomm's USB HS PHY
+
+PROPERTIES
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: Should contain "qcom,usb-hs-phy" and more specifically one of the
+ following:
+
+ "qcom,usb-hs-phy-apq8064"
+ "qcom,usb-hs-phy-msm8916"
+ "qcom,usb-hs-phy-msm8974"
+
+- #phy-cells:
+ Usage: required
+ Value type: <u32>
+ Definition: Should contain 0
+
+- clocks:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: Should contain clock specifier for the reference and sleep
+ clocks
+
+- clock-names:
+ Usage: required
+ Value type: <stringlist>
+ Definition: Should contain "ref" and "sleep" for the reference and sleep
+ clocks respectively
+
+- resets:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: Should contain the phy and POR resets
+
+- reset-names:
+ Usage: required
+ Value type: <stringlist>
+ Definition: Should contain "phy" and "por" for the phy and POR resets
+ respectively
+
+- v3p3-supply:
+ Usage: required
+ Value type: <phandle>
+ Definition: Should contain a reference to the 3.3V supply
+
+- v1p8-supply:
+ Usage: required
+ Value type: <phandle>
+ Definition: Should contain a reference to the 1.8V supply
+
+- extcon:
+ Usage: optional
+ Value type: <prop-encoded-array>
+ Definition: Should contain the vbus extcon
+
+- qcom,init-seq:
+ Usage: optional
+ Value type: <u8 array>
+ Definition: Should contain a sequence of ULPI address and value pairs to
+ program into the ULPI_EXT_VENDOR_SPECIFIC area. This is related
+ to Device Mode Eye Diagram test. The addresses are offsets
+ from the ULPI_EXT_VENDOR_SPECIFIC address, for example,
+ <0x1 0x53> would mean "write the value 0x53 to address 0x81".
+
+EXAMPLE
+
+otg: usb-controller {
+ ulpi {
+ phy {
+ compatible = "qcom,usb-hs-phy-msm8974", "qcom,usb-hs-phy";
+ #phy-cells = <0>;
+ clocks = <&xo_board>, <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
+ clock-names = "ref", "sleep";
+ resets = <&gcc GCC_USB2A_PHY_BCR>, <&otg 0>;
+ reset-names = "phy", "por";
+ v3p3-supply = <&pm8941_l24>;
+ v1p8-supply = <&pm8941_l6>;
+ extcon = <&smbb>;
+ qcom,init-seq = /bits/ 8 <0x1 0x63>;
+ };
+ };
+};
diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index a430a64981d5..61a22e985831 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -437,6 +437,14 @@ config PHY_QCOM_UFS
help
Support for UFS PHY on QCOM chipsets.
+config PHY_QCOM_USB_HS
+ tristate "Qualcomm USB HS PHY module"
+ depends on USB_ULPI_BUS
+ select GENERIC_PHY
+ help
+ Support for the USB high-speed ULPI compliant phy on Qualcomm
+ chipsets.
+
config PHY_QCOM_USB_HSIC
tristate "Qualcomm USB HSIC ULPI PHY module"
depends on USB_ULPI_BUS
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index c43c9df5d301..0e4259473d28 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -52,6 +52,7 @@ obj-$(CONFIG_PHY_STIH407_USB) += phy-stih407-usb.o
obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs.o
obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs-qmp-20nm.o
obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs-qmp-14nm.o
+obj-$(CONFIG_PHY_QCOM_USB_HS) += phy-qcom-usb-hs.o
obj-$(CONFIG_PHY_QCOM_USB_HSIC) += phy-qcom-usb-hsic.o
obj-$(CONFIG_PHY_TUSB1210) += phy-tusb1210.o
obj-$(CONFIG_PHY_BRCM_SATA) += phy-brcm-sata.o
diff --git a/drivers/phy/phy-qcom-usb-hs.c b/drivers/phy/phy-qcom-usb-hs.c
new file mode 100644
index 000000000000..94dfbfd739c3
--- /dev/null
+++ b/drivers/phy/phy-qcom-usb-hs.c
@@ -0,0 +1,296 @@
+/**
+ * Copyright (C) 2016 Linaro Ltd
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/module.h>
+#include <linux/ulpi/driver.h>
+#include <linux/ulpi/regs.h>
+#include <linux/clk.h>
+#include <linux/regulator/consumer.h>
+#include <linux/of_device.h>
+#include <linux/reset.h>
+#include <linux/extcon.h>
+#include <linux/notifier.h>
+
+#include "ulpi_phy.h"
+
+#define ULPI_PWR_CLK_MNG_REG 0x88
+# define ULPI_PWR_OTG_COMP_DISABLE BIT(0)
+
+#define ULPI_MISC_A 0x96
+# define ULPI_MISC_A_VBUSVLDEXTSEL BIT(1)
+# define ULPI_MISC_A_VBUSVLDEXT BIT(0)
+
+
+struct ulpi_seq {
+ u8 addr;
+ u8 val;
+};
+
+struct qcom_usb_hs_phy {
+ struct ulpi *ulpi;
+ struct phy *phy;
+ struct clk *ref_clk;
+ struct clk *sleep_clk;
+ struct regulator *v1p8;
+ struct regulator *v3p3;
+ struct reset_control *reset;
+ struct ulpi_seq *init_seq;
+ struct extcon_dev *vbus_edev;
+ struct notifier_block vbus_notify;
+};
+
+static int qcom_usb_hs_phy_set_mode(struct phy *phy, enum phy_mode mode)
+{
+ struct qcom_usb_hs_phy *uphy = phy_get_drvdata(phy);
+ u8 addr;
+ int ret;
+
+ if (!uphy->vbus_edev) {
+ u8 val = 0;
+
+ switch (mode) {
+ case PHY_MODE_USB_OTG:
+ case PHY_MODE_USB_HOST:
+ val |= ULPI_INT_IDGRD;
+ case PHY_MODE_USB_DEVICE:
+ val |= ULPI_INT_SESS_VALID;
+ default:
+ break;
+ }
+
+ ret = ulpi_write(uphy->ulpi, ULPI_USB_INT_EN_RISE, val);
+ if (ret)
+ return ret;
+ ret = ulpi_write(uphy->ulpi, ULPI_USB_INT_EN_FALL, val);
+ } else {
+ switch (mode) {
+ case PHY_MODE_USB_OTG:
+ case PHY_MODE_USB_DEVICE:
+ addr = ULPI_SET(ULPI_MISC_A);
+ break;
+ case PHY_MODE_USB_HOST:
+ addr = ULPI_CLR(ULPI_MISC_A);
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ ret = ulpi_write(uphy->ulpi, ULPI_SET(ULPI_PWR_CLK_MNG_REG),
+ ULPI_PWR_OTG_COMP_DISABLE);
+ if (ret)
+ return ret;
+ ret = ulpi_write(uphy->ulpi, addr, ULPI_MISC_A_VBUSVLDEXTSEL);
+ }
+
+ return ret;
+}
+
+static int
+qcom_usb_hs_phy_vbus_notifier(struct notifier_block *nb, unsigned long event,
+ void *ptr)
+{
+ struct qcom_usb_hs_phy *uphy;
+ u8 addr;
+
+ uphy = container_of(nb, struct qcom_usb_hs_phy, vbus_notify);
+
+ if (event)
+ addr = ULPI_SET(ULPI_MISC_A);
+ else
+ addr = ULPI_CLR(ULPI_MISC_A);
+
+ return ulpi_write(uphy->ulpi, addr, ULPI_MISC_A_VBUSVLDEXT);
+}
+
+static int qcom_usb_hs_phy_power_on(struct phy *phy)
+{
+ struct qcom_usb_hs_phy *uphy = phy_get_drvdata(phy);
+ struct ulpi *ulpi = uphy->ulpi;
+ const struct ulpi_seq *seq;
+ int ret, state;
+
+ ret = clk_prepare_enable(uphy->ref_clk);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(uphy->sleep_clk);
+ if (ret)
+ goto err_sleep;
+
+ ret = regulator_set_load(uphy->v1p8, 50000);
+ if (ret < 0)
+ goto err_1p8;
+
+ ret = regulator_enable(uphy->v1p8);
+ if (ret)
+ goto err_1p8;
+
+ ret = regulator_set_voltage_triplet(uphy->v3p3, 3050000, 3300000,
+ 3300000);
+ if (ret)
+ goto err_3p3;
+
+ ret = regulator_set_load(uphy->v3p3, 50000);
+ if (ret < 0)
+ goto err_3p3;
+
+ ret = regulator_enable(uphy->v3p3);
+ if (ret)
+ goto err_3p3;
+
+ for (seq = uphy->init_seq; seq->addr; seq++) {
+ ret = ulpi_write(ulpi, ULPI_EXT_VENDOR_SPECIFIC + seq->addr,
+ seq->val);
+ if (ret)
+ goto err_ulpi;
+ }
+
+ if (uphy->reset) {
+ ret = reset_control_reset(uphy->reset);
+ if (ret)
+ goto err_ulpi;
+ }
+
+ if (uphy->vbus_edev) {
+ state = extcon_get_cable_state_(uphy->vbus_edev, EXTCON_USB);
+ /* setup initial state */
+ qcom_usb_hs_phy_vbus_notifier(&uphy->vbus_notify, state,
+ uphy->vbus_edev);
+ ret = extcon_register_notifier(uphy->vbus_edev, EXTCON_USB,
+ &uphy->vbus_notify);
+ if (ret)
+ goto err_ulpi;
+ }
+
+ return 0;
+err_ulpi:
+ regulator_disable(uphy->v3p3);
+err_3p3:
+ regulator_disable(uphy->v1p8);
+err_1p8:
+ clk_disable_unprepare(uphy->sleep_clk);
+err_sleep:
+ clk_disable_unprepare(uphy->ref_clk);
+ return ret;
+}
+
+static int qcom_usb_hs_phy_power_off(struct phy *phy)
+{
+ int ret;
+ struct qcom_usb_hs_phy *uphy = phy_get_drvdata(phy);
+
+ if (uphy->vbus_edev) {
+ ret = extcon_unregister_notifier(uphy->vbus_edev, EXTCON_USB,
+ &uphy->vbus_notify);
+ if (ret)
+ return ret;
+ }
+
+ regulator_disable(uphy->v3p3);
+ regulator_disable(uphy->v1p8);
+ clk_disable_unprepare(uphy->sleep_clk);
+ clk_disable_unprepare(uphy->ref_clk);
+
+ return 0;
+}
+
+static const struct phy_ops qcom_usb_hs_phy_ops = {
+ .power_on = qcom_usb_hs_phy_power_on,
+ .power_off = qcom_usb_hs_phy_power_off,
+ .set_mode = qcom_usb_hs_phy_set_mode,
+ .owner = THIS_MODULE,
+};
+
+static int qcom_usb_hs_phy_probe(struct ulpi *ulpi)
+{
+ struct qcom_usb_hs_phy *uphy;
+ struct phy_provider *p;
+ struct clk *clk;
+ struct regulator *reg;
+ struct reset_control *reset;
+ int size;
+ int ret;
+
+ uphy = devm_kzalloc(&ulpi->dev, sizeof(*uphy), GFP_KERNEL);
+ if (!uphy)
+ return -ENOMEM;
+ ulpi_set_drvdata(ulpi, uphy);
+ uphy->ulpi = ulpi;
+
+ size = of_property_count_u8_elems(ulpi->dev.of_node, "qcom,init-seq");
+ if (size < 0)
+ size = 0;
+ uphy->init_seq = devm_kmalloc_array(&ulpi->dev, (size / 2) + 1,
+ sizeof(*uphy->init_seq), GFP_KERNEL);
+ if (!uphy->init_seq)
+ return -ENOMEM;
+ ret = of_property_read_u8_array(ulpi->dev.of_node, "qcom,init-seq",
+ (u8 *)uphy->init_seq, size);
+ if (ret && size)
+ return ret;
+ /* NUL terminate */
+ uphy->init_seq[size / 2].addr = uphy->init_seq[size / 2].val = 0;
+
+ uphy->ref_clk = clk = devm_clk_get(&ulpi->dev, "ref");
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ uphy->sleep_clk = clk = devm_clk_get(&ulpi->dev, "sleep");
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ uphy->v1p8 = reg = devm_regulator_get(&ulpi->dev, "v1p8");
+ if (IS_ERR(reg))
+ return PTR_ERR(reg);
+
+ uphy->v3p3 = reg = devm_regulator_get(&ulpi->dev, "v3p3");
+ if (IS_ERR(reg))
+ return PTR_ERR(reg);
+
+ uphy->reset = reset = devm_reset_control_get(&ulpi->dev, "por");
+ if (IS_ERR(reset)) {
+ if (PTR_ERR(reset) == -EPROBE_DEFER)
+ return PTR_ERR(reset);
+ uphy->reset = NULL;
+ }
+
+ uphy->phy = devm_phy_create(&ulpi->dev, ulpi->dev.of_node,
+ &qcom_usb_hs_phy_ops);
+ if (IS_ERR(uphy->phy))
+ return PTR_ERR(uphy->phy);
+
+ uphy->vbus_edev = extcon_get_edev_by_phandle(&ulpi->dev, 0);
+ if (IS_ERR(uphy->vbus_edev)) {
+ if (PTR_ERR(uphy->vbus_edev) != -ENODEV)
+ return PTR_ERR(uphy->vbus_edev);
+ uphy->vbus_edev = NULL;
+ }
+
+ uphy->vbus_notify.notifier_call = qcom_usb_hs_phy_vbus_notifier;
+ phy_set_drvdata(uphy->phy, uphy);
+
+ p = devm_of_phy_provider_register(&ulpi->dev, of_phy_simple_xlate);
+ return PTR_ERR_OR_ZERO(p);
+}
+
+static const struct of_device_id qcom_usb_hs_phy_match[] = {
+ { .compatible = "qcom,usb-hs-phy", },
+ { }
+};
+MODULE_DEVICE_TABLE(of, qcom_usb_hs_phy_match);
+
+static struct ulpi_driver qcom_usb_hs_phy_driver = {
+ .probe = qcom_usb_hs_phy_probe,
+ .driver = {
+ .name = "qcom_usb_hs_phy",
+ .of_match_table = qcom_usb_hs_phy_match,
+ },
+};
+module_ulpi_driver(qcom_usb_hs_phy_driver);
+
+MODULE_DESCRIPTION("Qualcomm USB HS phy");
+MODULE_LICENSE("GPL v2");
--
2.10.0.297.gf6727b0
^ permalink raw reply related [flat|nested] 17+ messages in thread* [PATCH v8 3/3] phy: Add support for Qualcomm's USB HS phy
@ 2017-01-25 22:32 ` Stephen Boyd
0 siblings, 0 replies; 17+ messages in thread
From: Stephen Boyd @ 2017-01-25 22:32 UTC (permalink / raw)
To: linux-arm-kernel
The high-speed phy on qcom SoCs is controlled via the ULPI
viewport.
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: <devicetree@vger.kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
---
.../devicetree/bindings/phy/qcom,usb-hs-phy.txt | 84 ++++++
drivers/phy/Kconfig | 8 +
drivers/phy/Makefile | 1 +
drivers/phy/phy-qcom-usb-hs.c | 296 +++++++++++++++++++++
4 files changed, 389 insertions(+)
create mode 100644 Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.txt
create mode 100644 drivers/phy/phy-qcom-usb-hs.c
diff --git a/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.txt b/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.txt
new file mode 100644
index 000000000000..b3b75c1e6285
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/qcom,usb-hs-phy.txt
@@ -0,0 +1,84 @@
+Qualcomm's USB HS PHY
+
+PROPERTIES
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: Should contain "qcom,usb-hs-phy" and more specifically one of the
+ following:
+
+ "qcom,usb-hs-phy-apq8064"
+ "qcom,usb-hs-phy-msm8916"
+ "qcom,usb-hs-phy-msm8974"
+
+- #phy-cells:
+ Usage: required
+ Value type: <u32>
+ Definition: Should contain 0
+
+- clocks:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: Should contain clock specifier for the reference and sleep
+ clocks
+
+- clock-names:
+ Usage: required
+ Value type: <stringlist>
+ Definition: Should contain "ref" and "sleep" for the reference and sleep
+ clocks respectively
+
+- resets:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: Should contain the phy and POR resets
+
+- reset-names:
+ Usage: required
+ Value type: <stringlist>
+ Definition: Should contain "phy" and "por" for the phy and POR resets
+ respectively
+
+- v3p3-supply:
+ Usage: required
+ Value type: <phandle>
+ Definition: Should contain a reference to the 3.3V supply
+
+- v1p8-supply:
+ Usage: required
+ Value type: <phandle>
+ Definition: Should contain a reference to the 1.8V supply
+
+- extcon:
+ Usage: optional
+ Value type: <prop-encoded-array>
+ Definition: Should contain the vbus extcon
+
+- qcom,init-seq:
+ Usage: optional
+ Value type: <u8 array>
+ Definition: Should contain a sequence of ULPI address and value pairs to
+ program into the ULPI_EXT_VENDOR_SPECIFIC area. This is related
+ to Device Mode Eye Diagram test. The addresses are offsets
+ from the ULPI_EXT_VENDOR_SPECIFIC address, for example,
+ <0x1 0x53> would mean "write the value 0x53 to address 0x81".
+
+EXAMPLE
+
+otg: usb-controller {
+ ulpi {
+ phy {
+ compatible = "qcom,usb-hs-phy-msm8974", "qcom,usb-hs-phy";
+ #phy-cells = <0>;
+ clocks = <&xo_board>, <&gcc GCC_USB2A_PHY_SLEEP_CLK>;
+ clock-names = "ref", "sleep";
+ resets = <&gcc GCC_USB2A_PHY_BCR>, <&otg 0>;
+ reset-names = "phy", "por";
+ v3p3-supply = <&pm8941_l24>;
+ v1p8-supply = <&pm8941_l6>;
+ extcon = <&smbb>;
+ qcom,init-seq = /bits/ 8 <0x1 0x63>;
+ };
+ };
+};
diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
index a430a64981d5..61a22e985831 100644
--- a/drivers/phy/Kconfig
+++ b/drivers/phy/Kconfig
@@ -437,6 +437,14 @@ config PHY_QCOM_UFS
help
Support for UFS PHY on QCOM chipsets.
+config PHY_QCOM_USB_HS
+ tristate "Qualcomm USB HS PHY module"
+ depends on USB_ULPI_BUS
+ select GENERIC_PHY
+ help
+ Support for the USB high-speed ULPI compliant phy on Qualcomm
+ chipsets.
+
config PHY_QCOM_USB_HSIC
tristate "Qualcomm USB HSIC ULPI PHY module"
depends on USB_ULPI_BUS
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index c43c9df5d301..0e4259473d28 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -52,6 +52,7 @@ obj-$(CONFIG_PHY_STIH407_USB) += phy-stih407-usb.o
obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs.o
obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs-qmp-20nm.o
obj-$(CONFIG_PHY_QCOM_UFS) += phy-qcom-ufs-qmp-14nm.o
+obj-$(CONFIG_PHY_QCOM_USB_HS) += phy-qcom-usb-hs.o
obj-$(CONFIG_PHY_QCOM_USB_HSIC) += phy-qcom-usb-hsic.o
obj-$(CONFIG_PHY_TUSB1210) += phy-tusb1210.o
obj-$(CONFIG_PHY_BRCM_SATA) += phy-brcm-sata.o
diff --git a/drivers/phy/phy-qcom-usb-hs.c b/drivers/phy/phy-qcom-usb-hs.c
new file mode 100644
index 000000000000..94dfbfd739c3
--- /dev/null
+++ b/drivers/phy/phy-qcom-usb-hs.c
@@ -0,0 +1,296 @@
+/**
+ * Copyright (C) 2016 Linaro Ltd
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#include <linux/module.h>
+#include <linux/ulpi/driver.h>
+#include <linux/ulpi/regs.h>
+#include <linux/clk.h>
+#include <linux/regulator/consumer.h>
+#include <linux/of_device.h>
+#include <linux/reset.h>
+#include <linux/extcon.h>
+#include <linux/notifier.h>
+
+#include "ulpi_phy.h"
+
+#define ULPI_PWR_CLK_MNG_REG 0x88
+# define ULPI_PWR_OTG_COMP_DISABLE BIT(0)
+
+#define ULPI_MISC_A 0x96
+# define ULPI_MISC_A_VBUSVLDEXTSEL BIT(1)
+# define ULPI_MISC_A_VBUSVLDEXT BIT(0)
+
+
+struct ulpi_seq {
+ u8 addr;
+ u8 val;
+};
+
+struct qcom_usb_hs_phy {
+ struct ulpi *ulpi;
+ struct phy *phy;
+ struct clk *ref_clk;
+ struct clk *sleep_clk;
+ struct regulator *v1p8;
+ struct regulator *v3p3;
+ struct reset_control *reset;
+ struct ulpi_seq *init_seq;
+ struct extcon_dev *vbus_edev;
+ struct notifier_block vbus_notify;
+};
+
+static int qcom_usb_hs_phy_set_mode(struct phy *phy, enum phy_mode mode)
+{
+ struct qcom_usb_hs_phy *uphy = phy_get_drvdata(phy);
+ u8 addr;
+ int ret;
+
+ if (!uphy->vbus_edev) {
+ u8 val = 0;
+
+ switch (mode) {
+ case PHY_MODE_USB_OTG:
+ case PHY_MODE_USB_HOST:
+ val |= ULPI_INT_IDGRD;
+ case PHY_MODE_USB_DEVICE:
+ val |= ULPI_INT_SESS_VALID;
+ default:
+ break;
+ }
+
+ ret = ulpi_write(uphy->ulpi, ULPI_USB_INT_EN_RISE, val);
+ if (ret)
+ return ret;
+ ret = ulpi_write(uphy->ulpi, ULPI_USB_INT_EN_FALL, val);
+ } else {
+ switch (mode) {
+ case PHY_MODE_USB_OTG:
+ case PHY_MODE_USB_DEVICE:
+ addr = ULPI_SET(ULPI_MISC_A);
+ break;
+ case PHY_MODE_USB_HOST:
+ addr = ULPI_CLR(ULPI_MISC_A);
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ ret = ulpi_write(uphy->ulpi, ULPI_SET(ULPI_PWR_CLK_MNG_REG),
+ ULPI_PWR_OTG_COMP_DISABLE);
+ if (ret)
+ return ret;
+ ret = ulpi_write(uphy->ulpi, addr, ULPI_MISC_A_VBUSVLDEXTSEL);
+ }
+
+ return ret;
+}
+
+static int
+qcom_usb_hs_phy_vbus_notifier(struct notifier_block *nb, unsigned long event,
+ void *ptr)
+{
+ struct qcom_usb_hs_phy *uphy;
+ u8 addr;
+
+ uphy = container_of(nb, struct qcom_usb_hs_phy, vbus_notify);
+
+ if (event)
+ addr = ULPI_SET(ULPI_MISC_A);
+ else
+ addr = ULPI_CLR(ULPI_MISC_A);
+
+ return ulpi_write(uphy->ulpi, addr, ULPI_MISC_A_VBUSVLDEXT);
+}
+
+static int qcom_usb_hs_phy_power_on(struct phy *phy)
+{
+ struct qcom_usb_hs_phy *uphy = phy_get_drvdata(phy);
+ struct ulpi *ulpi = uphy->ulpi;
+ const struct ulpi_seq *seq;
+ int ret, state;
+
+ ret = clk_prepare_enable(uphy->ref_clk);
+ if (ret)
+ return ret;
+
+ ret = clk_prepare_enable(uphy->sleep_clk);
+ if (ret)
+ goto err_sleep;
+
+ ret = regulator_set_load(uphy->v1p8, 50000);
+ if (ret < 0)
+ goto err_1p8;
+
+ ret = regulator_enable(uphy->v1p8);
+ if (ret)
+ goto err_1p8;
+
+ ret = regulator_set_voltage_triplet(uphy->v3p3, 3050000, 3300000,
+ 3300000);
+ if (ret)
+ goto err_3p3;
+
+ ret = regulator_set_load(uphy->v3p3, 50000);
+ if (ret < 0)
+ goto err_3p3;
+
+ ret = regulator_enable(uphy->v3p3);
+ if (ret)
+ goto err_3p3;
+
+ for (seq = uphy->init_seq; seq->addr; seq++) {
+ ret = ulpi_write(ulpi, ULPI_EXT_VENDOR_SPECIFIC + seq->addr,
+ seq->val);
+ if (ret)
+ goto err_ulpi;
+ }
+
+ if (uphy->reset) {
+ ret = reset_control_reset(uphy->reset);
+ if (ret)
+ goto err_ulpi;
+ }
+
+ if (uphy->vbus_edev) {
+ state = extcon_get_cable_state_(uphy->vbus_edev, EXTCON_USB);
+ /* setup initial state */
+ qcom_usb_hs_phy_vbus_notifier(&uphy->vbus_notify, state,
+ uphy->vbus_edev);
+ ret = extcon_register_notifier(uphy->vbus_edev, EXTCON_USB,
+ &uphy->vbus_notify);
+ if (ret)
+ goto err_ulpi;
+ }
+
+ return 0;
+err_ulpi:
+ regulator_disable(uphy->v3p3);
+err_3p3:
+ regulator_disable(uphy->v1p8);
+err_1p8:
+ clk_disable_unprepare(uphy->sleep_clk);
+err_sleep:
+ clk_disable_unprepare(uphy->ref_clk);
+ return ret;
+}
+
+static int qcom_usb_hs_phy_power_off(struct phy *phy)
+{
+ int ret;
+ struct qcom_usb_hs_phy *uphy = phy_get_drvdata(phy);
+
+ if (uphy->vbus_edev) {
+ ret = extcon_unregister_notifier(uphy->vbus_edev, EXTCON_USB,
+ &uphy->vbus_notify);
+ if (ret)
+ return ret;
+ }
+
+ regulator_disable(uphy->v3p3);
+ regulator_disable(uphy->v1p8);
+ clk_disable_unprepare(uphy->sleep_clk);
+ clk_disable_unprepare(uphy->ref_clk);
+
+ return 0;
+}
+
+static const struct phy_ops qcom_usb_hs_phy_ops = {
+ .power_on = qcom_usb_hs_phy_power_on,
+ .power_off = qcom_usb_hs_phy_power_off,
+ .set_mode = qcom_usb_hs_phy_set_mode,
+ .owner = THIS_MODULE,
+};
+
+static int qcom_usb_hs_phy_probe(struct ulpi *ulpi)
+{
+ struct qcom_usb_hs_phy *uphy;
+ struct phy_provider *p;
+ struct clk *clk;
+ struct regulator *reg;
+ struct reset_control *reset;
+ int size;
+ int ret;
+
+ uphy = devm_kzalloc(&ulpi->dev, sizeof(*uphy), GFP_KERNEL);
+ if (!uphy)
+ return -ENOMEM;
+ ulpi_set_drvdata(ulpi, uphy);
+ uphy->ulpi = ulpi;
+
+ size = of_property_count_u8_elems(ulpi->dev.of_node, "qcom,init-seq");
+ if (size < 0)
+ size = 0;
+ uphy->init_seq = devm_kmalloc_array(&ulpi->dev, (size / 2) + 1,
+ sizeof(*uphy->init_seq), GFP_KERNEL);
+ if (!uphy->init_seq)
+ return -ENOMEM;
+ ret = of_property_read_u8_array(ulpi->dev.of_node, "qcom,init-seq",
+ (u8 *)uphy->init_seq, size);
+ if (ret && size)
+ return ret;
+ /* NUL terminate */
+ uphy->init_seq[size / 2].addr = uphy->init_seq[size / 2].val = 0;
+
+ uphy->ref_clk = clk = devm_clk_get(&ulpi->dev, "ref");
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ uphy->sleep_clk = clk = devm_clk_get(&ulpi->dev, "sleep");
+ if (IS_ERR(clk))
+ return PTR_ERR(clk);
+
+ uphy->v1p8 = reg = devm_regulator_get(&ulpi->dev, "v1p8");
+ if (IS_ERR(reg))
+ return PTR_ERR(reg);
+
+ uphy->v3p3 = reg = devm_regulator_get(&ulpi->dev, "v3p3");
+ if (IS_ERR(reg))
+ return PTR_ERR(reg);
+
+ uphy->reset = reset = devm_reset_control_get(&ulpi->dev, "por");
+ if (IS_ERR(reset)) {
+ if (PTR_ERR(reset) == -EPROBE_DEFER)
+ return PTR_ERR(reset);
+ uphy->reset = NULL;
+ }
+
+ uphy->phy = devm_phy_create(&ulpi->dev, ulpi->dev.of_node,
+ &qcom_usb_hs_phy_ops);
+ if (IS_ERR(uphy->phy))
+ return PTR_ERR(uphy->phy);
+
+ uphy->vbus_edev = extcon_get_edev_by_phandle(&ulpi->dev, 0);
+ if (IS_ERR(uphy->vbus_edev)) {
+ if (PTR_ERR(uphy->vbus_edev) != -ENODEV)
+ return PTR_ERR(uphy->vbus_edev);
+ uphy->vbus_edev = NULL;
+ }
+
+ uphy->vbus_notify.notifier_call = qcom_usb_hs_phy_vbus_notifier;
+ phy_set_drvdata(uphy->phy, uphy);
+
+ p = devm_of_phy_provider_register(&ulpi->dev, of_phy_simple_xlate);
+ return PTR_ERR_OR_ZERO(p);
+}
+
+static const struct of_device_id qcom_usb_hs_phy_match[] = {
+ { .compatible = "qcom,usb-hs-phy", },
+ { }
+};
+MODULE_DEVICE_TABLE(of, qcom_usb_hs_phy_match);
+
+static struct ulpi_driver qcom_usb_hs_phy_driver = {
+ .probe = qcom_usb_hs_phy_probe,
+ .driver = {
+ .name = "qcom_usb_hs_phy",
+ .of_match_table = qcom_usb_hs_phy_match,
+ },
+};
+module_ulpi_driver(qcom_usb_hs_phy_driver);
+
+MODULE_DESCRIPTION("Qualcomm USB HS phy");
+MODULE_LICENSE("GPL v2");
--
2.10.0.297.gf6727b0
^ permalink raw reply related [flat|nested] 17+ messages in thread