[PATCH 3/4] irqchip/mbigen: add support for a MBIGEN generating SPIs

[yangyingliang@huawei.com (Yang Yingliang)]

Hi, Marc

On 2018/10/18 0:30, Marc Zyngier wrote:
> On 16/10/18 10:15, Yang Yingliang wrote:
>> Now with
>> 5052875 ("irqchip/gic-v3: Add support for Message Based Interrupts as an MSI controller"),
>> we can support MBIGEN to generate message based SPIs by writing GICD_SETSPIR.
>>
>> The first 64-pins of each MBIGEN chip is used to generate SPIs, and each
>> MBIGEN chip has several MBIGEN nodes, every node has 128 pins for generating
>> LPIs. The total pins are: 64(SPIs) + 128 * node_nr(LPIs). So we can translate
>> the pin index in a unified way in mbigen_domain_translate().
>>
>> Also Add TYPE and VEC registers that used by generating SPIs, the driver can
>> access them when MBIGEN is used to generate SPIs.
>>
>> Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
>> ---
>>   drivers/irqchip/irq-mbigen.c | 21 +++++++++++++++++++--
>>   1 file changed, 19 insertions(+), 2 deletions(-)
>>
>> diff --git a/drivers/irqchip/irq-mbigen.c b/drivers/irqchip/irq-mbigen.c
>> index f05998f..37c1932 100644
>> --- a/drivers/irqchip/irq-mbigen.c
>> +++ b/drivers/irqchip/irq-mbigen.c
>> @@ -48,6 +48,7 @@
>>   #define MBIGEN_NODE_OFFSET		0x1000
>>   
>>   /* offset of vector register in mbigen node */
>> +#define REG_MBIGEN_SPI_VEC_OFFSET	0x500
>>   #define REG_MBIGEN_LPI_VEC_OFFSET	0x200
>>   
>>   /**
>> @@ -62,6 +63,7 @@
>>    * This register is used to configure interrupt
>>    * trigger type
>>    */
>> +#define REG_MBIGEN_SPI_TYPE_OFFSET	0x400
>>   #define REG_MBIGEN_LPI_TYPE_OFFSET	0x0
>>   
>>   /**
>> @@ -79,6 +81,9 @@ static inline unsigned int get_mbigen_vec_reg(irq_hw_number_t hwirq)
>>   {
>>   	unsigned int nid, pin;
>>   
>> +	if (hwirq < SPI_NUM_PER_MBIGEN_CHIP)
>> +		return (hwirq * 4 + REG_MBIGEN_SPI_VEC_OFFSET);
>> +
>>   	hwirq -= SPI_NUM_PER_MBIGEN_CHIP;
>>   	nid = hwirq / IRQS_PER_MBIGEN_NODE + 1;
>>   	pin = hwirq % IRQS_PER_MBIGEN_NODE;
>> @@ -92,6 +97,13 @@ static inline void get_mbigen_type_reg(irq_hw_number_t hwirq,
>>   {
>>   	unsigned int nid, irq_ofst, ofst;
>>   
>> +	if (hwirq < SPI_NUM_PER_MBIGEN_CHIP) {
>> +		*mask = 1 << (hwirq % 32);
>> +		ofst = hwirq / 32 * 4;
>> +		*addr = ofst + REG_MBIGEN_SPI_TYPE_OFFSET;
>> +		return;
>> +	}
>> +
>>   	hwirq -= SPI_NUM_PER_MBIGEN_CHIP;
>>   	nid = hwirq / IRQS_PER_MBIGEN_NODE + 1;
>>   	irq_ofst = hwirq % IRQS_PER_MBIGEN_NODE;
>> @@ -162,6 +174,12 @@ static void mbigen_write_msg(struct msi_desc *desc, struct msi_msg *msg)
>>   	u32 val;
>>   
>>   	base += get_mbigen_vec_reg(d->hwirq);
>> +
>> +	if (d->hwirq < SPI_NUM_PER_MBIGEN_CHIP) {
>> +		writel_relaxed(msg->data, base);
>> +		return;
>> +	}
> How is the GICD_SETSPI_NSR base address programmed if you're ignoring
> the address stored in the message?
Now, this base address is encoded in MBIGEN register by default.

In case this address isn't set to register in later SoCs, I think the
MBIGEN driver set this base address would be better. I will add
relative codes to handle both GICD_SETSPI_NSR and ITS Translate
address.

>
> How do you deal with level interrupts, as you don't seem to use the
> level MSI framework either?
The MBIGEN driver need to clear active state in irq_eoi hook, when it
dealing with level SPIs.

>
>> +
>>   	val = readl_relaxed(base);
>>   
>>   	val &= ~(IRQ_EVENT_ID_MASK << IRQ_EVENT_ID_SHIFT);
>> @@ -182,8 +200,7 @@ static int mbigen_domain_translate(struct irq_domain *d,
>>   		if (fwspec->param_count != 2)
>>   			return -EINVAL;
>>   
>> -		if ((fwspec->param[0] > MAXIMUM_IRQ_PIN_NUM) ||
>> -			(fwspec->param[0] < SPI_NUM_PER_MBIGEN_CHIP))
>> +		if (fwspec->param[0] > MAXIMUM_IRQ_PIN_NUM)
>>   			return -EINVAL;
>>   		else
>>   			*hwirq = fwspec->param[0];
>>
> Now, the biggest question of them all: how does it work with ACPI? Last
> time I checked, there was no DT support for platforms using the MBIGEN.
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/arch/arm64/boot/dts/hisilicon/hip07.dtsi
This DT describes how platform devices using the MBIGEN.

>
> My gut feeling is that it would be so much better if the SPIs generated
> by the MBIGEN were configured in firmware, and the devices behind it
> would just describe the corresponding SPI...
We need use this framework to clear active state in MBIGEN register, so 
configuring
in firmware is not enough...

Regards,
Yang
>
> Thanks,
>
> 	M.