* ath10k with EEPROM regdomain 0x60
@ 2019-07-19 8:03 Hermida, Isaac
0 siblings, 0 replies; only message in thread
From: Hermida, Isaac @ 2019-07-19 8:03 UTC (permalink / raw)
To: linux-wireless@vger.kernel.org
Hi,
I have a problem with the ath10k driver when using a board data with the
World Wide regdomain.
The problem I see is that the country code is not reflected in the FW.
When I load the driver with the regdomain in the EEPROM to 0x60, the
regulatory domain of the system is set to 00 (this is correct)
# driver load relevant messages
[ 30.609243] ath10k_pci 0000:01:00.0: htt-ver 3.53 wmi-op 4 htt-op 3
cal otp max-sta 32 raw 0 hwcrypto 1
[ 30.688608] ath: EEPROM regdomain: 0x60
[ 30.688616] ath: EEPROM indicates we should expect a direct regpair map
[ 30.688629] ath: Country alpha2 being used: 00
[ 30.692688] ath: Regpair used: 0x60
# ifconfig wlan0 up
[ 35.793804] ath10k_pci 0000:01:00.0: Unknown eventid: 3
[ 35.819288] ath10k_pci 0000:01:00.0: Unknown eventid: 118809
[ 35.822234] ath10k_pci 0000:01:00.0: Unknown eventid: 90118
[ 35.845798] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
# iw reg get
global
country 00: DFS-UNSET
(2402 - 2472 @ 40), (N/A, 20), (N/A)
(2457 - 2482 @ 20), (N/A, 20), (N/A), AUTO-BW, NO-IR
(2474 - 2494 @ 20), (N/A, 20), (N/A), NO-OFDM, NO-IR
(5170 - 5250 @ 80), (N/A, 20), (N/A), AUTO-BW, NO-IR
(5250 - 5330 @ 80), (N/A, 20), (0 ms), DFS, AUTO-BW, NO-IR
(5490 - 5730 @ 160), (N/A, 20), (0 ms), DFS, NO-IR
(5735 - 5835 @ 80), (N/A, 20), (N/A), NO-IR
(57240 - 63720 @ 2160), (N/A, 0), (N/A)
Just at this point, checking the available channels, it shows that
channels 40 and 44 can be used (first thing wrong)
# iw list | grep -E " MHz " | grep -Ev "disabled|radar"
* 2412 MHz [1] (20.0 dBm)
* 2417 MHz [2] (20.0 dBm)
* 2422 MHz [3] (20.0 dBm)
* 2427 MHz [4] (20.0 dBm)
* 2432 MHz [5] (20.0 dBm)
* 2437 MHz [6] (20.0 dBm)
* 2442 MHz [7] (20.0 dBm)
* 2447 MHz [8] (20.0 dBm)
* 2452 MHz [9] (20.0 dBm)
* 2457 MHz [10] (20.0 dBm)
* 2462 MHz [11] (20.0 dBm)
* 2467 MHz [12] (20.0 dBm) (no IR)
* 2472 MHz [13] (20.0 dBm) (no IR)
* 2484 MHz [14] (20.0 dBm) (no IR)
* 5180 MHz [36] (30.0 dBm) (no IR)
* 5200 MHz [40] (30.0 dBm)
* 5220 MHz [44] (30.0 dBm)
* 5240 MHz [48] (30.0 dBm) (no IR)
* 5720 MHz [144] (30.0 dBm) (no IR)
* 5745 MHz [149] (30.0 dBm) (no IR)
* 5765 MHz [153] (30.0 dBm) (no IR)
* 5785 MHz [157] (30.0 dBm) (no IR)
* 5805 MHz [161] (30.0 dBm) (no IR)
* 5825 MHz [165] (30.0 dBm) (no IR)
* 5845 MHz [169] (30.0 dBm) (no IR)
Apart of that, if I set a country manually, the system is reconfigured
to that domain and I see the next messages.
# iw reg set DE
[ 163.571806] ath: EEPROM regdomain: 0x8114
[ 163.576283] ath: EEPROM indicates we should expect a country code
[ 163.576287] ath: doing EEPROM country->regdmn map search
[ 163.576290] ath: country maps to regdmn code: 0x37
[ 163.576293] ath: Country alpha2 being used: DE
[ 163.576296] ath: Regpair used: 0x37
[ 163.576301] ath: regdomain 0x8114 dynamically updated by user
And this is how the regulatory is set.
# iw reg get
global
country DE: DFS-ETSI
(2400 - 2483 @ 40), (N/A, 20), (N/A)
(5150 - 5250 @ 80), (N/A, 23), (N/A), NO-OUTDOOR, AUTO-BW
(5250 - 5350 @ 80), (N/A, 20), (0 ms), NO-OUTDOOR, DFS, AUTO-BW
(5470 - 5725 @ 160), (N/A, 26), (0 ms), DFS
(5725 - 5875 @ 80), (N/A, 13), (N/A)
(57000 - 66000 @ 2160), (N/A, 40), (N/A)
And checking again, the channels are incorrect (see the NO-IR), so I can
not use those channels (I want to use them as access point)
# iw list | grep -E " MHz " | grep -Ev "disabled|radar"
* 2412 MHz [1] (20.0 dBm)
* 2417 MHz [2] (20.0 dBm)
* 2422 MHz [3] (20.0 dBm)
* 2427 MHz [4] (20.0 dBm)
* 2432 MHz [5] (20.0 dBm)
* 2437 MHz [6] (20.0 dBm)
* 2442 MHz [7] (20.0 dBm)
* 2447 MHz [8] (20.0 dBm)
* 2452 MHz [9] (20.0 dBm)
* 2457 MHz [10] (20.0 dBm)
* 2462 MHz [11] (20.0 dBm)
* 2467 MHz [12] (20.0 dBm) (no IR)
* 2472 MHz [13] (20.0 dBm) (no IR)
* 5180 MHz [36] (23.0 dBm) (no IR)
* 5200 MHz [40] (23.0 dBm)
* 5220 MHz [44] (23.0 dBm)
* 5240 MHz [48] (23.0 dBm) (no IR)
* 5745 MHz [149] (13.0 dBm) (no IR)
* 5765 MHz [153] (13.0 dBm) (no IR)
* 5785 MHz [157] (13.0 dBm) (no IR)
* 5805 MHz [161] (13.0 dBm) (no IR)
* 5825 MHz [165] (13.0 dBm) (no IR)
* 5845 MHz [169] (13.0 dBm) (no IR)
On the other hand, if I use a fixed country, everything works fine.
[ 22.820336] ath: EEPROM regdomain: 0x8348
[ 22.820343] ath: EEPROM indicates we should expect a country code
[ 22.820349] ath: doing EEPROM country->regdmn map search
[ 22.820353] ath: country maps to regdmn code: 0x3a
[ 22.820357] ath: Country alpha2 being used: US
[ 22.820360] ath: Regpair used: 0x3a
# iw reg get
global
country US: DFS-FCC
(2402 - 2472 @ 40), (N/A, 30), (N/A)
(5170 - 5250 @ 80), (N/A, 23), (N/A), AUTO-BW
(5250 - 5330 @ 80), (N/A, 23), (0 ms), DFS, AUTO-BW
(5490 - 5730 @ 160), (N/A, 23), (0 ms), DFS
(5735 - 5835 @ 80), (N/A, 30), (N/A)
(57240 - 63720 @ 2160), (N/A, 40), (N/A)
phy#0
country US: DFS-FCC
(2402 - 2472 @ 40), (N/A, 30), (N/A)
(5170 - 5250 @ 80), (N/A, 23), (N/A), AUTO-BW
(5250 - 5330 @ 80), (N/A, 23), (0 ms), DFS, AUTO-BW
(5490 - 5730 @ 160), (N/A, 23), (0 ms), DFS
(5735 - 5835 @ 80), (N/A, 30), (N/A)
(57240 - 63720 @ 2160), (N/A, 40), (N/A)
# iw list | grep -E " MHz " | grep -Ev "disabled|radar"
* 2412 MHz [1] (30.0 dBm)
* 2417 MHz [2] (30.0 dBm)
* 2422 MHz [3] (30.0 dBm)
* 2427 MHz [4] (30.0 dBm)
* 2432 MHz [5] (30.0 dBm)
* 2437 MHz [6] (30.0 dBm)
* 2442 MHz [7] (30.0 dBm)
* 2447 MHz [8] (30.0 dBm)
* 2452 MHz [9] (30.0 dBm)
* 2457 MHz [10] (30.0 dBm)
* 2462 MHz [11] (30.0 dBm)
* 5180 MHz [36] (23.0 dBm)
* 5200 MHz [40] (23.0 dBm)
* 5220 MHz [44] (23.0 dBm)
* 5240 MHz [48] (23.0 dBm)
* 5745 MHz [149] (30.0 dBm)
* 5765 MHz [153] (30.0 dBm)
* 5785 MHz [157] (30.0 dBm)
* 5805 MHz [161] (30.0 dBm)
* 5825 MHz [165] (30.0 dBm)
Is this a bug? any fix on that?
Also notice, that for the World Wide case, there is not phy#0, only a
global entry, just in case it can give more light on the problem
^ permalink raw reply [flat|nested] only message in thread
only message in thread, other threads:[~2019-07-19 8:03 UTC | newest]
Thread overview: (only message) (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2019-07-19 8:03 ath10k with EEPROM regdomain 0x60 Hermida, Isaac
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.