* SATA detect fails on ICH7 chipset / Dell Poweredge SC430
@ 2005-08-30 11:02 Chris Bainbridge
0 siblings, 0 replies; 3+ messages in thread
From: Chris Bainbridge @ 2005-08-30 11:02 UTC (permalink / raw)
To: xen-devel
[-- Attachment #1: Type: text/plain, Size: 514 bytes --]
Hi,
I have a Dell Poweredge SC420 and a SC430. The SC420 has an ICH6
chipset and works ok with Xen. The SC430 has an ICH7 chipset and the
SATA detection fails. I've tried 2.6.11.10 and 2.6.12.5 kernels, with
Xen 2.0.7, Xen-testing and Xen-unstable, all with the same results.
I'm using the same hypervisor and kernel binaries, so problems with
the compiler environment etc. have been ruled out.
Boot logs attached from Xen-unstable on 2.6.12.5 kernel. Any fixes
would be welcome :-)
Cheers,
Chris
[-- Attachment #2: boot.2.6.12.5-xen.sc420.good --]
[-- Type: application/octet-stream, Size: 10540 bytes --]
Linux version 2.6.12.5-xen (root@xenmaster) (gcc version 3.4.4 (Gentoo 3.4.4, ssp-3.4.4-1.0, pie-8.7.8)) #2 Mon Aug 29 18:56:29 GMT 2005
BIOS-provided physical RAM map:
Xen: 0000000000000000 - 0000000006000000 (usable)
0MB HIGHMEM available.
96MB LOWMEM available.
found SMP MP-table at 000fe710
DMI 2.3 present.
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x07] disabled)
ACPI: LAPIC_NMI (acpi_id[0xff] high level lint[0x1])
ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
IRQ lockup detection disabled
Allocating PCI resources starting at 06000000 (gap: 06000000:fa000000)
Built 1 zonelists
Kernel command line: root=/dev/md1 noreboot console=ttyS0
Initializing CPU#0
PID hash table entries: 512 (order: 9, 8192 bytes)
Xen reported: 2793.128 MHz processor.
Console: colour VGA+ 80x25
Linux version 2.6.12.5-xen (root@xenmaster) (gcc version 3.4.4 (Gentoo 3.4.4, ssp-3.4.4-1.0, pie-8.7.8)) #2 Mon Aug 29 18:56:29 GMT 2005
BIOS-provided physical RAM map:
Xen: 0000000000000000 - 0000000006000000 (usable)
0MB HIGHMEM available.
96MB LOWMEM available.
found SMP MP-table at 000fe710
DMI 2.3 present.
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x07] disabled)
ACPI: LAPIC_NMI (acpi_id[0xff] high level lint[0x1])
ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
IRQ lockup detection disabled
Allocating PCI resources starting at 06000000 (gap: 06000000:fa000000)
Built 1 zonelists
Kernel command line: root=/dev/md1 noreboot console=ttyS0
Initializing CPU#0
PID hash table entries: 512 (order: 9, 8192 bytes)
Xen reported: 2793.128 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
vmalloc area: c6800000-fb7fe000, maxmem 34000000
Memory: 94208k/98304k available (1931k kernel code, 4048k reserved, 618k data, 140k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Mount-cache hash table entries: 512
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... disabled
ENABLING IO-APIC IRQs
NET: Registered protocol family 16
PCI: Using MMCONFIG
ACPI: Subsystem revision 20050309
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12 15)
xen_mem: Initialising balloon driver.
SCSI subsystem initialized
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
Grant table initialized
IA-32 Microcode Update Driver: v1.14-xen <tigran@veritas.com>
Simple Boot Flag value 0x87 read from CMOS RAM was invalid
Simple Boot Flag at 0x7a set to 0x1
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
assign_interrupt_mode Found MSI capability
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
assign_interrupt_mode Found MSI capability
ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 17 (level, low) -> IRQ 17
assign_interrupt_mode Found MSI capability
Linux agpgart interface v0.101 (c) Dave Jones
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 16 (level, low) -> IRQ 16
ttyS4: detected caps 00000700 should be 00000100
ttyS4 at I/O 0xd820 (irq = 16) is a 16C950/954
ttyS5: detected caps 00000700 should be 00000100
ttyS5 at I/O 0xd828 (irq = 16) is a 16C950/954
ttyS6: detected caps 00000700 should be 00000100
ttyS6 at I/O 0xd830 (irq = 16) is a 16C950/954
ttyS7: detected caps 00000700 should be 00000100
ttyS7 at I/O 0xd838 (irq = 16) is a 16C950/954
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
tg3.c:v3.31 (June 8, 2005)
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
eth0: Tigon3 [partno(BCM95751) rev 4001 PHY(5750)] (PCIX:100MHz:32-bit) 10/100/1000BaseT Ethernet 00:11:11:cc:66:d1
eth0: RXcsums[1] LinkChgREG[1] MIirq[1] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
eth0: dma_rwctrl[76180000]
WARNING: Failed to register Xen virtual console driver as 'ttyS0'
Event-channel device installed.
Initialising Xen netif backend
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH6: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 16 (level, low) -> IRQ 16
ICH6: chipset revision 3
ICH6: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
hda: GCR-8483B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ACPI: PCI Interrupt 0000:00:1f.2[C] -> GSI 20 (level, low) -> IRQ 20
ahci(0000:00:1f.2) AHCI 0001.0000 32 slots 4 ports 1.5 Gbps 0xf impl IDE mode
ahci(0000:00:1f.2) flags: 64bit ncq pm led slum part
ata1: SATA max UDMA/133 cmd 0xC6804D00 ctl 0x0 bmdma 0x0 irq 20
ata2: SATA max UDMA/133 cmd 0xC6804D80 ctl 0x0 bmdma 0x0 irq 20
ata3: SATA max UDMA/133 cmd 0xC6804E00 ctl 0x0 bmdma 0x0 irq 20
ata4: SATA max UDMA/133 cmd 0xC6804E80 ctl 0x0 bmdma 0x0 irq 20
ata1: dev 0 ATA, max UDMA/133, 156250000 sectors:
ata1: dev 0 configured for UDMA/133
scsi0 : ahci
ata2: dev 0 ATA, max UDMA/133, 160086528 sectors:
ata2: dev 0 configured for UDMA/133
scsi1 : ahci
ata3: no device found (phy stat 00000000)
scsi2 : ahci
ata4: no device found (phy stat 00000000)
scsi3 : ahci
Vendor: ATA Model: Maxtor 6Y080M0 Rev: YAR5
Type: Direct-Access ANSI SCSI revision: 05
Vendor: ATA Model: Maxtor 6Y080M0 Rev: YAR5
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 156250000 512-byte hdwr sectors (80000 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 156250000 512-byte hdwr sectors (80000 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sdb: 160086528 512-byte hdwr sectors (81964 MB)
SCSI device sdb: drive cache: write back
SCSI device sdb: 160086528 512-byte hdwr sectors (81964 MB)
SCSI device sdb: drive cache: write back
sdb: sdb1 sdb2 sdb3
Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
Attached scsi generic sg1 at scsi1, channel 0, id 0, lun 0, type 0
USB Universal Host Controller Interface driver v2.2
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 21, io base 0x0000ff80
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 22 (level, low) -> IRQ 22
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 22, io base 0x0000ff60
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000ff40
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 23, io base 0x0000ff20
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
mice: PS/2 mouse device common for all mice
md: raid1 personality registered as nr 3
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
NET: Registered protocol family 2
input: AT Translated Set 2 keyboard on isa0060/serio0
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
NET: Registered protocol family 1
NET: Registered protocol family 17
Bridge firewalling registered
md: Autodetecting RAID arrays.
md: autorun ...
md: considering sdb3 ...
md: adding sdb3 ...
md: sdb1 has different UUID to sdb3
md: adding sda3 ...
md: sda1 has different UUID to sdb3
md: created md1
md: bind<sda3>
md: bind<sdb3>
md: running: <sdb3><sda3>
raid1: raid set md1 active with 2 out of 2 mirrors
md: considering sdb1 ...
md: adding sdb1 ...
md: adding sda1 ...
md: created md0
md: bind<sda1>
md: bind<sdb1>
md: running: <sdb1><sda1>
raid1: raid set md0 active with 2 out of 2 mirrors
md: ... autorun DONE.
ReiserFS: md1: found reiserfs format "3.6" with standard journal
[-- Attachment #3: boot.2.6.12.5-xen.sc430.bad --]
[-- Type: application/octet-stream, Size: 8177 bytes --]
Linux version 2.6.12.5-xen (root@xenmaster) (gcc version 3.4.4 (Gentoo 3.4.4, ssp-3.4.4-1.0, pie-8.7.8)) #2 Mon Aug 29 18:56:29 GMT 2005
BIOS-provided physical RAM map:
Xen: 0000000000000000 - 0000000006000000 (usable)
0MB HIGHMEM available.
96MB LOWMEM available.
found SMP MP-table at 000fe710
DMI 2.3 present.
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x06] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x07] disabled)
ACPI: LAPIC_NMI (acpi_id[0xff] high level lint[0x1])
ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
IRQ lockup detection disabled
Allocating PCI resources starting at 06000000 (gap: 06000000:fa000000)
Built 1 zonelists
Kernel command line: root=/dev/md2 noreboot console=ttyS0
Initializing CPU#0
PID hash table entries: 512 (order: 9, 8192 bytes)
Xen reported: 2793.130 MHz processor.
Console: colour VGA+ 80x25
Linux version 2.6.12.5-xen (root@xenmaster) (gcc version 3.4.4 (Gentoo 3.4.4, ssp-3.4.4-1.0, pie-8.7.8)) #2 Mon Aug 29 18:56:29 GMT 2005
BIOS-provided physical RAM map:
Xen: 0000000000000000 - 0000000006000000 (usable)
0MB HIGHMEM available.
96MB LOWMEM available.
found SMP MP-table at 000fe710
DMI 2.3 present.
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x06] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x07] disabled)
ACPI: LAPIC_NMI (acpi_id[0xff] high level lint[0x1])
ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
IRQ lockup detection disabled
Allocating PCI resources starting at 06000000 (gap: 06000000:fa000000)
Built 1 zonelists
Kernel command line: root=/dev/md2 noreboot console=ttyS0
Initializing CPU#0
PID hash table entries: 512 (order: 9, 8192 bytes)
Xen reported: 2793.130 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
vmalloc area: c6800000-fb7fe000, maxmem 34000000
Memory: 94208k/98304k available (1931k kernel code, 4048k reserved, 618k data, 140k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Mount-cache hash table entries: 512
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... disabled
ENABLING IO-APIC IRQs
NET: Registered protocol family 16
PCI: Using MMCONFIG
ACPI: Subsystem revision 20050309
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12 15)
xen_mem: Initialising balloon driver.
SCSI subsystem initialized
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
Grant table initialized
IA-32 Microcode Update Driver: v1.14-xen <tigran@veritas.com>
Simple Boot Flag at 0x7a set to 0x1
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
assign_interrupt_mode Found MSI capability
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
assign_interrupt_mode Found MSI capability
ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 16 (level, low) -> IRQ 16
assign_interrupt_mode Found MSI capability
ACPI: PCI Interrupt 0000:00:1c.5[B] -> GSI 17 (level, low) -> IRQ 17
assign_interrupt_mode Found MSI capability
Linux agpgart interface v0.101 (c) Dave Jones
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
tg3.c:v3.31 (June 8, 2005)
ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 17 (level, low) -> IRQ 17
eth0: Tigon3 [partno(BCM95751) rev 4001 PHY(5750)] (PCIX:100MHz:32-bit) 10/100/1000BaseT Ethernet 00:12:3f:71:ed:be
eth0: RXcsums[1] LinkChgREG[1] MIirq[1] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
eth0: dma_rwctrl[76180000]
WARNING: Failed to register Xen virtual console driver as 'ttyS0'
Event-channel device installed.
Initialising Xen netif backend
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH7: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 16 (level, low) -> IRQ 16
ICH7: chipset revision 1
ICH7: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
hda: HL-DT-STDVD-ROM GDR8163B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ata_piix: probe of 0000:00:1f.2 failed with error -12
USB Universal Host Controller Interface driver v2.2
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 21, io base 0x0000ff80
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 22 (level, low) -> IRQ 22
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 22, io base 0x0000ff60
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000ff40
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 23, io base 0x0000ff20
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
mice: PS/2 mouse device common for all mice
md: raid1 personality registered as nr 3
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
NET: Registered protocol family 2
usb 4-1: new low speed USB device using uhci_hcd and address 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
NET: Registered protocol family 1
NET: Registered protocol family 17
Bridge firewalling registered
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
VFS: Cannot open root device "md2" or unknown-block(0,0)
Please append a correct "root=" boot option
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
[-- Attachment #4: Type: text/plain, Size: 138 bytes --]
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel
^ permalink raw reply [flat|nested] 3+ messages in thread
* RE: SATA detect fails on ICH7 chipset / Dell Poweredge SC430
@ 2005-08-30 11:22 Ian Pratt
2005-08-30 12:03 ` Chris Bainbridge
0 siblings, 1 reply; 3+ messages in thread
From: Ian Pratt @ 2005-08-30 11:22 UTC (permalink / raw)
To: Chris Bainbridge, xen-devel
> I have a Dell Poweredge SC420 and a SC430. The SC420 has an
> ICH6 chipset and works ok with Xen. The SC430 has an ICH7
> chipset and the SATA detection fails. I've tried 2.6.11.10
> and 2.6.12.5 kernels, with Xen 2.0.7, Xen-testing and
> Xen-unstable, all with the same results.
> I'm using the same hypervisor and kernel binaries, so
> problems with the compiler environment etc. have been ruled out.
>
> Boot logs attached from Xen-unstable on 2.6.12.5 kernel. Any
> fixes would be welcome :-)
Having the bootlog from a native build of 2.6.12.5 would be useful to
compare against the 2.6.12.5-xen0.
When running native linux, what driver is used for the SATA controller?
Are you sure its actually compiled in to our -xen0 config?
Incidently, have you tried using the -xen kerenel plus modules that are
in our -unstable install tar ball? This is the kernel that end-users
are intended to use: -xen0/-xenU are just for developers' convenience
(fewer modules, faster to build).
Best,
Ian
^ permalink raw reply [flat|nested] 3+ messages in thread
* Re: SATA detect fails on ICH7 chipset / Dell Poweredge SC430
2005-08-30 11:22 Ian Pratt
@ 2005-08-30 12:03 ` Chris Bainbridge
0 siblings, 0 replies; 3+ messages in thread
From: Chris Bainbridge @ 2005-08-30 12:03 UTC (permalink / raw)
To: xen-devel
[-- Attachment #1: Type: text/plain, Size: 1759 bytes --]
> Having the bootlog from a native build of 2.6.12.5 would be useful to
> compare against the 2.6.12.5-xen0.
Attached.
> When running native linux, what driver is used for the SATA controller?
> Are you sure its actually compiled in to our -xen0 config?
The one in Config->SCSI->Sata->Intel PIIX/ICH SATA Support. I have
the AHCI driver builtin as well.
I'm sure the SATA support works. I've used the exact same hypervisor
and kernel images to boot on the sc420, and the same driver works on
the sc430 without Xen.
The difference seems to be that under sc430-xen we get:
ata_piix: probe of 0000:00:1f.2 failed with error -12
instead of (sc430 native):
ACPI: PCI Interrupt 0000:00:1f.2[C] -> GSI 20 (level, low) -> IRQ 20
ata1: SATA max UDMA/133 cmd 0xFE00 ctl 0xFE12 bmdma 0xFEA0 irq 20
ata2: SATA max UDMA/133 cmd 0xFE20 ctl 0xFE32 bmdma 0xFEA8 irq 20
or (sc420-xen):
ACPI: PCI Interrupt 0000:00:1f.2[C] -> GSI 20 (level, low) -> IRQ 20
ahci(0000:00:1f.2) AHCI 0001.0000 32 slots 4 ports 1.5 Gbps 0xf impl IDE mode
ahci(0000:00:1f.2) flags: 64bit ncq pm led slum part
It seems the sc430-xen isn't doing something related to ACPI that
enables the hardware to be detected?
> Incidently, have you tried using the -xen kerenel plus modules that are
> in our -unstable install tar ball? This is the kernel that end-users
> are intended to use: -xen0/-xenU are just for developers' convenience
> (fewer modules, faster to build).
I took the unstable tarball, patched the kernel with the
patches/linux-2.6.12 diffs, and copied over the linux-2.6-xen-sparse
directory. After building it boots on the sc420 so I don't think it's
a problem with the build stage, but I can try something else if it
would help.
[-- Attachment #2: boot.2.6.12.5-native.sc430.good --]
[-- Type: application/octet-stream, Size: 20796 bytes --]
Linux version 2.6.12.5-xen (root@xenmaster) (gcc version 3.4.4 (Gentoo 3.4.4, ssp-3.4.4-1.0, pie-8.7.8)) #2 Mon Aug 29 18:56:29 GMT 2005
BIOS-provided physical RAM map:
Xen: 0000000000000000 - 0000000006000000 (usable)
0MB HIGHMEM available.
96MB LOWMEM available.
found SMP MP-table at 000fe710
DMI 2.3 present.
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x06] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x07] disabled)
ACPI: LAPIC_NMI (acpi_id[0xff] high level lint[0x1])
ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
IRQ lockup detection disabled
Allocating PCI resources starting at 06000000 (gap: 06000000:fa000000)
Built 1 zonelists
Kernel command line: root=/dev/md2 noreboot console=ttyS0
Initializing CPU#0
PID hash table entries: 512 (order: 9, 8192 bytes)
Xen reported: 2793.130 MHz processor.
Console: colour VGA+ 80x25
Linux version 2.6.12.5-xen (root@xenmaster) (gcc version 3.4.4 (Gentoo 3.4.4, ssp-3.4.4-1.0, pie-8.7.8)) #2 Mon Aug 29 18:56:29 GMT 2005
BIOS-provided physical RAM map:
Xen: 0000000000000000 - 0000000006000000 (usable)
0MB HIGHMEM available.
96MB LOWMEM available.
found SMP MP-table at 000fe710
DMI 2.3 present.
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x06] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x07] disabled)
ACPI: LAPIC_NMI (acpi_id[0xff] high level lint[0x1])
ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
IRQ lockup detection disabled
Allocating PCI resources starting at 06000000 (gap: 06000000:fa000000)
Built 1 zonelists
Kernel command line: root=/dev/md2 noreboot console=ttyS0
Initializing CPU#0
PID hash table entries: 512 (order: 9, 8192 bytes)
Xen reported: 2793.130 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
vmalloc area: c6800000-fb7fe000, maxmem 34000000
Memory: 94208k/98304k available (1931k kernel code, 4048k reserved, 618k data, 140k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Mount-cache hash table entries: 512
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... disabled
ENABLING IO-APIC IRQs
NET: Registered protocol family 16
PCI: Using MMCONFIG
ACPI: Subsystem revision 20050309
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12 15)
xen_mem: Initialising balloon driver.
SCSI subsystem initialized
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
Grant table initialized
IA-32 Microcode Update Driver: v1.14-xen <tigran@veritas.com>
Simple Boot Flag at 0x7a set to 0x1
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
assign_interrupt_mode Found MSI capability
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
assign_interrupt_mode Found MSI capability
ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 16 (level, low) -> IRQ 16
assign_interrupt_mode Found MSI capability
ACPI: PCI Interrupt 0000:00:1c.5[B] -> GSI 17 (level, low) -> IRQ 17
assign_interrupt_mode Found MSI capability
Linux agpgart interface v0.101 (c) Dave Jones
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
tg3.c:v3.31 (June 8, 2005)
ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 17 (level, low) -> IRQ 17
eth0: Tigon3 [partno(BCM95751) rev 4001 PHY(5750)] (PCIX:100MHz:32-bit) 10/100/1000BaseT Ethernet 00:12:3f:71:ed:be
eth0: RXcsums[1] LinkChgREG[1] MIirq[1] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
eth0: dma_rwctrl[76180000]
WARNING: Failed to register Xen virtual console driver as 'ttyS0'
Event-channel device installed.
Initialising Xen netif backend
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH7: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 16 (level, low) -> IRQ 16
ICH7: chipset revision 1
ICH7: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
hda: HL-DT-STDVD-ROM GDR8163B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ata_piix: probe of 0000:00:1f.2 failed with error -12
USB Universal Host Controller Interface driver v2.2
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 21, io base 0x0000ff80
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 22 (level, low) -> IRQ 22
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 22, io base 0x0000ff60
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000ff40
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 23, io base 0x0000ff20
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
mice: PS/2 mouse device common for all mice
md: raid1 personality registered as nr 3
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
NET: Registered protocol family 2
usb 4-1: new low speed USB device using uhci_hcd and address 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
NET: Registered protocol family 1
NET: Registered protocol family 17
Bridge firewalling registered
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
VFS: Cannot open root device "md2" or unknown-block(0,0)
Please append a correct "root=" boot option
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(0,0)
Linux version 2.6.12.5 (root@xenmaster) (gcc version 3.4.4 (Gentoo 3.4.4, ssp-3.4.4-1.0, pie-8.7.8)) #5 SMP Mon Aug 29 11:42:41 GMT 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fe8cc00 (usable)
BIOS-e820: 000000003fe8cc00 - 000000003fe8ec00 (ACPI NVS)
BIOS-e820: 000000003fe8ec00 - 000000003fe90c00 (ACPI data)
BIOS-e820: 000000003fe90c00 - 0000000040000000 (reserved)
BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fed00400 (reserved)
BIOS-e820: 00000000fed20000 - 00000000feda0000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved)
BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
Warning only 896MB will be used.
Use a HIGHMEM enabled kernel.
896MB LOWMEM available.
found SMP MP-table at 000fe710
DMI 2.3 present.
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:4 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:4 APIC version 20
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x06] disabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x07] disabled)
ACPI: LAPIC_NMI (acpi_id[0xff] high level lint[0x1])
ACPI: IOAPIC (id[0x08] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 8, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 40000000:b0000000)
Built 1 zonelists
Kernel command line: ro root=/dev/md2 console=ttyS0
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 2794.128 MHz processor.
Using tsc for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 905424k/917504k available (2153k kernel code, 11568k reserved, 924k data, 204k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Mount-cache hash table entries: 512
monitor/mwait feature present.
using mwait in idle threads.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
CPU0: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 01
Booting processor 1/1 eip 3000
Initializing CPU#1
monitor/mwait feature present.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (24) available
CPU1: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 01
Total of 2 processors activated (11075.58 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfbcb2, last bus=5
PCI: Using MMCONFIG
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050309
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 9 10 11 12 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 *10 11 12 15)
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
Simple Boot Flag at 0x7a set to 0x1
audit: initializing netlink socket (disabled)
audit(1125405043.897:0): initialized
Initializing Cryptographic API
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
assign_interrupt_mode Found MSI capability
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
assign_interrupt_mode Found MSI capability
ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 16 (level, low) -> IRQ 16
assign_interrupt_mode Found MSI capability
ACPI: PCI Interrupt 0000:00:1c.5[B] -> GSI 17 (level, low) -> IRQ 17
assign_interrupt_mode Found MSI capability
ACPI: Power Button (FF) [PWRF]
Generic RTC Driver v1.07
Linux agpgart interface v0.101 (c) Dave Jones
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
Floppy drive(s): fd0 is 1.44M
floppy0: no floppy controllers found
tg3.c:v3.31 (June 8, 2005)
ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 17 (level, low) -> IRQ 17
eth0: Tigon3 [partno(BCM95751) rev 4001 PHY(5750)] (PCIX:100MHz:32-bit) 10/100/1000BaseT Ethernet 00:12:3f:71:ed:be
eth0: RXcsums[1] LinkChgREG[1] MIirq[1] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
eth0: dma_rwctrl[76180000]
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH7: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 16 (level, low) -> IRQ 16
ICH7: chipset revision 1
ICH7: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
hda: HL-DT-STDVD-ROM GDR8163B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hda: ATAPI 48X DVD-ROM drive, 256kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
ACPI: PCI Interrupt 0000:00:1f.2[C] -> GSI 20 (level, low) -> IRQ 20
ata1: SATA max UDMA/133 cmd 0xFE00 ctl 0xFE12 bmdma 0xFEA0 irq 20
ata2: SATA max UDMA/133 cmd 0xFE20 ctl 0xFE32 bmdma 0xFEA8 irq 20
ata1: dev 0 ATA, max UDMA/133, 312500000 sectors: lba48
ata1: dev 1 ATA, max UDMA/133, 312500000 sectors: lba48
ata1: dev 0 configured for UDMA/133
ata1: dev 1 configured for UDMA/133
scsi0 : ata_piix
ATA: abnormal status 0xFF on port 0xFE27
ata2: disabling port
scsi1 : ata_piix
Vendor: ATA Model: Maxtor 6Y160M0 Rev: YAR5
Type: Direct-Access ANSI SCSI revision: 05
Vendor: ATA Model: Maxtor 6Y160M0 Rev: YAR5
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 312500000 512-byte hdwr sectors (160000 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 312500000 512-byte hdwr sectors (160000 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 sda4
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sdb: 312500000 512-byte hdwr sectors (160000 MB)
SCSI device sdb: drive cache: write back
SCSI device sdb: 312500000 512-byte hdwr sectors (160000 MB)
SCSI device sdb: drive cache: write back
sdb: sdb1 sdb2 sdb3 sdb4
Attached scsi disk sdb at scsi0, channel 0, id 1, lun 0
Attached scsi generic sg0 at scsi0, channel 0, id 0, lun 0, type 0
Attached scsi generic sg1 at scsi0, channel 0, id 1, lun 0, type 0
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 21 (level, low) -> IRQ 21
ehci_hcd 0000:00:1d.7: Intel Corporation I/O Controller Hub EHCI USB
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: irq 21, io mem 0xffa80800
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
USB Universal Host Controller Interface driver v2.2
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 21 (level, low) -> IRQ 21
uhci_hcd 0000:00:1d.0: Intel Corporation I/O Controller Hub UHCI USB #1
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 21, io base 0x0000ff80
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 22 (level, low) -> IRQ 22
uhci_hcd 0000:00:1d.1: Intel Corporation I/O Controller Hub UHCI USB #2
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 22, io base 0x0000ff60
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: Intel Corporation I/O Controller Hub UHCI USB #3
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000ff40
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 23 (level, low) -> IRQ 23
uhci_hcd 0000:00:1d.3: Intel Corporation I/O Controller Hub UHCI USB #4
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1d.3: irq 23, io base 0x0000ff20
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb 5-1: new low speed USB device using uhci_hcd and address 2
input: USB HID v1.10 Keyboard [1267:0103] on usb-0000:00:1d.3-1
input: USB HID v1.10 Device [1267:0103] on usb-0000:00:1d.3-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
mice: PS/2 mouse device common for all mice
i2c /dev entries driver
md: raid1 personality registered as nr 3
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
Advanced Linux Sound Architecture Driver Version 1.0.9rc2 (Thu Mar 24 10:33:39 2005 UTC).
ALSA device list:
No soundcards found.
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
NET: Registered protocol family 1
NET: Registered protocol family 17
p4-clockmod: P4/Xeon(TM) CPU On-Demand Clock Modulation available
Starting balanced_irq
ACPI wakeup devices:
VBTN PCI0 PCI4 PCI2 PCI3 PCI1 PCI5 PCI6 USB0 USB1 USB2 USB3
ACPI: (supports S0 S1 S4 S5)
md: Autodetecting RAID arrays.
md: autorun ...
md: considering sdb4 ...
md: adding sdb4 ...
md: sdb3 has different UUID to sdb4
md: sdb2 has different UUID to sdb4
md: sdb1 has different UUID to sdb4
md: sda3 has different UUID to sdb4
md: sda2 has different UUID to sdb4
md: sda1 has different UUID to sdb4
md: created md3
md: bind<sdb4>
md: running: <sdb4>
raid1: raid set md3 active with 1 out of 2 mirrors
md: considering sdb3 ...
md: adding sdb3 ...
md: sdb2 has different UUID to sdb3
md: sdb1 has different UUID to sdb3
md: adding sda3 ...
md: sda2 has different UUID to sdb3
md: sda1 has different UUID to sdb3
md: created md2
md: bind<sda3>
md: bind<sdb3>
md: running: <sdb3><sda3>
raid1: raid set md2 active with 2 out of 2 mirrors
md: considering sdb2 ...
md: adding sdb2 ...
md: sdb1 has different UUID to sdb2
md: adding sda2 ...
md: sda1 has different UUID to sdb2
md: created md1
md: bind<sda2>
md: bind<sdb2>
md: running: <sdb2><sda2>
raid1: raid set md1 active with 2 out of 2 mirrors
md: considering sdb1 ...
md: adding sdb1 ...
md: adding sda1 ...
md: created md0
md: bind<sda1>
md: bind<sdb1>
md: running: <sdb1><sda1>
raid1: raid set md0 active with 2 out of 2 mirrors
md: ... autorun DONE.
ReiserFS: md2: found reiserfs format "3.6" with standard journal
ReiserFS: md2: using ordered data mode
ReiserFS: md2: journal params: device md2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
ReiserFS: md2: checking transaction log (md2)
ReiserFS: md2: Using r5 hash to sort names
VFS: Mounted root (reiserfs filesystem) readonly.
Freeing unused kernel memory: 204k freed
INIT: version 2.86 booting
Gentoo Linux; http://www.gentoo.org/
Copyright 1999-2005 Gentoo Foundation; Distributed under the GPLv2
Press I to enter interactive boot mode
[-- Attachment #3: Type: text/plain, Size: 138 bytes --]
_______________________________________________
Xen-devel mailing list
Xen-devel@lists.xensource.com
http://lists.xensource.com/xen-devel
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2005-08-30 12:03 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2005-08-30 11:02 SATA detect fails on ICH7 chipset / Dell Poweredge SC430 Chris Bainbridge
-- strict thread matches above, loose matches on Subject: below --
2005-08-30 11:22 Ian Pratt
2005-08-30 12:03 ` Chris Bainbridge
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.