From: Irwan Siajadi <dev.bahamot@yahoo.com>
To: Dan Williams <dcbw@redhat.com>
Cc: linux-wireless@vger.kernel.org
Subject: Re: ath5k: can't browse at all.
Date: Mon, 24 Nov 2008 18:30:56 -0800 (PST) [thread overview]
Message-ID: <630929.9910.qm@web59607.mail.ac4.yahoo.com> (raw)
In-Reply-To: <1227552872.25089.3.camel@localhost.localdomain>
--- On Mon, 11/24/08, Dan Williams <dcbw@redhat.com> wrote:
> From: Dan Williams <dcbw@redhat.com>
> Subject: Re: ath5k: can't browse at all.
> To: "Irwan Siajadi" <dev.bahamot@yahoo.com>
> Cc: linux-wireless@vger.kernel.org
> Date: Monday, November 24, 2008, 6:54 PM
> On Mon, 2008-11-24 at 09:41 -0800, Irwan Siajadi wrote:
> > The AR2425 is able to obtain IP address from the
> router,
> > able to ping with good results, but can't browse
> at all.
> > Below are the info on my setup, if you need more info
> please let me know.
>
> Can you traceroute to some IP, say like 4.2.2.1 or 4.2.2.2?
Trace seems to work fine. I believe this is a driver problem because I can browse normally as soon as I changed it to ndiswrapper.
Tracepath to osnews.com (using ath5k):
1: 192.168.1.2 (192.168.1.2) 0.225ms pmtu 1500
1: home.gateway (192.168.1.254) 1.217ms asymm 101
1: home.gateway (192.168.1.254) 1.181ms asymm 101
2: home.gateway (192.168.1.254) 1.186ms pmtu 1492
2: 125.167.124.1 (125.167.124.1) 112.890ms
3: 125.160.1.165 (125.160.1.165) 117.249ms
4: no reply
5: 203.208.191.81 (203.208.191.81) 513.481ms asymm 12
6: ge-0-1-7-0.sngtp-dr2.ix.singtel.com (203.208.151.181) 648.204ms asymm 12
7: ge-5-0-0-0.sngtp-cr1.ix.singtel.com (203.208.151.149) 629.931ms asymm 13
8: so-2-0-0-0.plapx-cr2.ix.singtel.com (203.208.149.182) 827.446ms asymm 14
9: ge-6-0-0-0.plapx-dr2.ix.singtel.com (203.208.183.166) 770.144ms asymm 15
10: ge6-0-128.ir1.paloalto-ca.us.xo.net (206.111.12.45) 738.330ms asymm 15
11: te-4-0-0.rar3.sanjose-ca.us.xo.net (207.88.12.61) 758.889ms asymm 16
12: te-3-0-0.rar3.la-ca.us.xo.net (207.88.12.62) 770.112ms asymm 20
13: 207.88.14.33.ptr.us.xo.net (207.88.14.33) 976.042ms asymm 18
14: 207.88.14.34.ptr.us.xo.net (207.88.14.34) 814.660ms asymm 19
15: 207.88.185.74.ptr.us.xo.net (207.88.185.74) 548.507ms asymm 23
16: border3.tge3-1-bbnet1.ext1.dal.pnap.net (216.52.191.22) 392.415ms asymm 23
17: te2-1.cer03.dal01.dallas-datacenter.com (216.52.189.30) 400.309ms asymm 20
18: po3.dar02.dal01.dallas-datacenter.com (66.228.118.211) 405.547ms asymm 19
19: po2.fcr02.dal01.dallas-datacenter.com (66.228.118.182) 404.016ms asymm 20
20: osnews.com (74.86.31.159) 406.893ms reached
Resume: pmtu 1492 hops 20 back 44
>
> Dan
>
> > Driver version: compat-wireless-2008-11-24.tar.bz2.
> > Kernel: 2.6.27.4-2mnbcustom (mandriva), compiled with
> mandriva provided
> > ..config but without any WLAN support except
> WIRELESS_EXT.
> > Access point/router is configured to use channel 1
> (2.412GHz).
> >
> > dmesg:
> > "...
> > cfg80211: Using static regulatory domain info
> > cfg80211: Regulatory domain: JP
> > (start_freq - end_freq @ bandwidth),
> (max_antenna_gain, max_eirp)
> > (2402000 KHz - 2494000 KHz @ 40000 KHz),
> (600 mBi, 2000 mBm)
> > (5160000 KHz - 5250000 KHz @ 40000 KHz),
> (600 mBi, 2000 mBm)
> > (5250000 KHz - 5330000 KHz @ 40000 KHz),
> (600 mBi, 2000 mBm)
> > cfg80211: Calling CRDA for country: JP
> > .....
> > ath5k 0000:05:00.0: PCI INT A -> GSI 16 (level,
> low) -> IRQ 16
> > ath5k 0000:05:00.0: setting latency timer to 64
> > ath5k 0000:05:00.0: registered as 'phy0'
> > phy0: Selected rate control algorithm
> 'minstrel'
> > ath5k phy0: Atheros AR2425 chip found (MAC: 0xe2, PHY:
> 0x70)
> > .....
> > wlan0: authenticate with AP 00:04:ed:42:60:67
> > wlan0: authenticated
> > wlan0: associate with AP 00:04:ed:42:60:67
> > wlan0: RX AssocResp from 00:04:ed:42:60:67
> (capab=3D0x431 status=3D0 id=3D)
> > wlan0: associated
> > ....."
> >
> > lspci:
> > "05:00.0 Ethernet controller: Atheros
> Communications Inc. AR242x 802.11abg
> > Wireless PCI Express Adapter (rev 01)
> > Subsystem: Device 1a3b:1026
> > Flags: bus master, fast devsel, latency 0,
> IRQ 16
> > Memory at feaf0000 (64-bit,
> non-prefetchable) [size=3D64K]
> > Capabilities: [40] Power Management version
> 2
> > Capabilities: [50] Message Signalled
> Interrupts: Mask- 64bit Queue=3D0/0 Enable-
> > Capabilities: [60] Express Legacy Endpoint,
> MSI 00
> > Capabilities: [90] MSI-X: Enable- Mask-
> TabSize=3D1
> > Capabilities: [100] Advanced Error Reporting
> <?>
> > Capabilities: [140] Virtual Channel
> <?>"
> >
> > TIA,
> > Irwan.
> >
> >
> >
> >
> > --
> > To unsubscribe from this list: send the line
> "unsubscribe linux-wireless" in
> > the body of a message to majordomo@vger.kernel.org
> > More majordomo info at
> http://vger.kernel.org/majordomo-info.html
next prev parent reply other threads:[~2008-11-25 2:36 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-11-24 17:41 ath5k: can't browse at all Irwan Siajadi
2008-11-24 18:53 ` Pavel Roskin
2008-11-25 2:36 ` Irwan Siajadi
2008-11-25 17:24 ` Irwan Siajadi
2008-11-25 20:02 ` Pavel Roskin
2008-11-30 16:53 ` Irwan Siajadi
2008-12-01 17:11 ` Luis R. Rodriguez
2008-11-24 18:54 ` Dan Williams
2008-11-25 2:30 ` Irwan Siajadi [this message]
-- strict thread matches above, loose matches on Subject: below --
2008-12-02 3:11 Irwan Siajadi
2008-12-01 21:36 ` Luis R. Rodriguez
2008-12-02 7:27 ` Irwan Siajadi
2008-12-02 8:00 ` Luis R. Rodriguez
2008-12-02 13:04 ` Irwan Siajadi
2008-12-07 19:39 ` Irwan Siajadi
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=630929.9910.qm@web59607.mail.ac4.yahoo.com \
--to=dev.bahamot@yahoo.com \
--cc=dcbw@redhat.com \
--cc=linux-wireless@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.