* Re: [PATCH v1 2/3] Bluetooth: btintel_pcie: Add support for PCIE transport
2024-03-28 11:19 ` [PATCH v1 2/3] Bluetooth: btintel_pcie: Add support for PCIE transport Kiran K
@ 2024-03-28 12:24 ` Paul Menzel
2024-05-07 13:34 ` K, Kiran
2024-03-28 14:09 ` Luiz Augusto von Dentz
2024-03-28 17:08 ` Bjorn Helgaas
2 siblings, 1 reply; 16+ messages in thread
From: Paul Menzel @ 2024-03-28 12:24 UTC (permalink / raw)
To: Kiran K
Cc: linux-bluetooth, ravishankar.srivatsa, chethan.tumkur.narayan,
Tedd Ho-Jeong An, linux-pci
Dear Tedd, dear Kiran,
Thank you for the patch. What a diffstat. ;-) Nice work.
Am 28.03.24 um 12:19 schrieb Kiran K:
> From: Tedd Ho-Jeong An <tedd.an@intel.com>
>
> Add initial code to support Intel bluetooth devices based on PICE
> transport. This patch allocates memory for buffers, internal structures,
> initializes interrupts for TX & RX and initializes PCIE device.
For a 1782 diffstat this is quite terse. Could you elaborate?
Also, it’d be great if you mentioned the datasheet, and how you tested
this. Maybe even paste the new log messages.
Also how well does the driver perform? What tools did you run to verify
the correctness und the “speed”?
> Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
> Co-developed-by: Kiran K <kiran.k@intel.com>
> Signed-off-by: Kiran K <kiran.k@intel.com>
> ---
> drivers/bluetooth/Kconfig | 14 +
> drivers/bluetooth/Makefile | 1 +
> drivers/bluetooth/btintel.h | 2 +-
> drivers/bluetooth/btintel_pcie.c | 1317 ++++++++++++++++++++++++++++++
> drivers/bluetooth/btintel_pcie.h | 449 ++++++++++
> 5 files changed, 1782 insertions(+), 1 deletion(-)
> create mode 100644 drivers/bluetooth/btintel_pcie.c
> create mode 100644 drivers/bluetooth/btintel_pcie.h
Should an entry be added to `MAINTAINERS`? It’d be good to mention in
the commit message, who the maintainer is.
>
> diff --git a/drivers/bluetooth/Kconfig b/drivers/bluetooth/Kconfig
> index bc211c324206..387f7b14461d 100644
> --- a/drivers/bluetooth/Kconfig
> +++ b/drivers/bluetooth/Kconfig
> @@ -23,6 +23,20 @@ config BT_MTK
> tristate
> select FW_LOADER
>
> +config BT_INTEL_PCIE
> + tristate "Intel Bluetooth transport driver for PCIe"
In the commit message summary you spell it PCIE. Please be consistent.
> + depends on PCI
> + select BT_INTEL
> + select FW_LOADER
> + default y
> + help
> + Intel Bluetooth transport driver for PCIe.
> + This driver is required if you want to use Intel Bluetooth device
> + with PCIe interface.
> +
> + Say Y here to compiler support for Intel Bluetooth PCIe device into
> + the kernel or say M to compile it as module (btintel_pcie)
> +
> config BT_HCIBTUSB
> tristate "HCI USB driver"
> depends on USB
> diff --git a/drivers/bluetooth/Makefile b/drivers/bluetooth/Makefile
> index 7a5967e9ac48..0730d6684d1a 100644
> --- a/drivers/bluetooth/Makefile
> +++ b/drivers/bluetooth/Makefile
> @@ -17,6 +17,7 @@ obj-$(CONFIG_BT_HCIBTUSB) += btusb.o
> obj-$(CONFIG_BT_HCIBTSDIO) += btsdio.o
>
> obj-$(CONFIG_BT_INTEL) += btintel.o
> +obj-$(CONFIG_BT_INTEL_PCIE) += btintel_pcie.o btintel.o
> obj-$(CONFIG_BT_ATH3K) += ath3k.o
> obj-$(CONFIG_BT_MRVL) += btmrvl.o
> obj-$(CONFIG_BT_MRVL_SDIO) += btmrvl_sdio.o
> diff --git a/drivers/bluetooth/btintel.h b/drivers/bluetooth/btintel.h
> index 1462a57420a0..5d4685b5c1fa 100644
> --- a/drivers/bluetooth/btintel.h
> +++ b/drivers/bluetooth/btintel.h
> @@ -209,7 +209,7 @@ struct btintel_data {
> #define btintel_wait_on_flag_timeout(hdev, nr, m, to) \
> wait_on_bit_timeout(btintel_get_flag(hdev), (nr), m, to)
>
> -#if IS_ENABLED(CONFIG_BT_INTEL)
> +#if IS_ENABLED(CONFIG_BT_INTEL) || IS_ENABLED(CONFIG_BT_INTEL_PCIE)
>
> int btintel_check_bdaddr(struct hci_dev *hdev);
> int btintel_enter_mfg(struct hci_dev *hdev);
> diff --git a/drivers/bluetooth/btintel_pcie.c b/drivers/bluetooth/btintel_pcie.c
> new file mode 100644
> index 000000000000..e6ce2304dc57
> --- /dev/null
> +++ b/drivers/bluetooth/btintel_pcie.c
> @@ -0,0 +1,1317 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +/*
> + * Intel Bluetooth PCIE driver
> + *
> + * Copyright (C) 2017 Intel Corporation. All rights reserved.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License version
> + * 2 as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Copyright (C) 2022 Intel Corporation
Are two copyright lines needed?
> + *
> + * Intel Bluetooth Driver for PCIE interface.
> + */
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/firmware.h>
> +#include <linux/pci.h>
> +#include <linux/wait.h>
> +#include <linux/delay.h>
> +#include <linux/interrupt.h>
> +
> +#include <asm/unaligned.h>
> +
> +#include <net/bluetooth/bluetooth.h>
> +#include <net/bluetooth/hci_core.h>
> +
> +#include "btintel.h"
> +#include "btintel_pcie.h"
> +
> +#define VERSION "0.1"
> +
> +#define BTINTEL_PCI_DEVICE(dev, subdev) \
> + .vendor = PCI_VENDOR_ID_INTEL, \
> + .device = (dev), \
> + .subvendor = PCI_ANY_ID, \
> + .subdevice = (subdev), \
> + .driver_data = 0
> +
> +/* Intel Bluetooth PCIe device id table */
> +static const struct pci_device_id btintel_pcie_table[] = {
> + { BTINTEL_PCI_DEVICE(0xA876, PCI_ANY_ID) },
> + { 0 }
> +};
> +MODULE_DEVICE_TABLE(pci, btintel_pcie_table);
> +
> +/* Intel PCIe uses 4 bytes of HCI type instead of 1 byte BT SIG HCI type */
> +#define BTINTEL_PCIE_HCI_TYPE_LEN 4
> +#define BTINTEL_PCIE_HCI_CMD_PKT 0x00000001
> +#define BTINTEL_PCIE_HCI_ACL_PKT 0x00000002
> +#define BTINTEL_PCIE_HCI_SCO_PKT 0x00000003
> +#define BTINTEL_PCIE_HCI_EVT_PKT 0x00000004
> +
> +#define BTITNEL_PCIE_ENABLE_HCI_DUMP 0
Mention this macro in the commit message?
> +
> +#if BTITNEL_PCIE_ENABLE_HCI_DUMP
> +static inline void btintel_pcie_hci_dump(const char *p, const void *b, int s)
> +{
> + const unsigned char *ptr = (const unsigned char *)b;
> + char str[64];
> + int c, i;
> +
> + for (i = c = 0; c < s; c++) {
> + i += snprintf(str + i, sizeof(str) - i, "%02x ", ptr[c]);
> + if ((c > 0 && (c + 1) % 8 == 0) || (c == s - 1)) {
> + BT_DBG("%s: %s", p, str);
> + i = 0;
> + }
> + }
> +}
> +#else
> +static inline void btintel_pcie_hci_dump(const char *p, const void *b, int s)
> +{
> +}
> +#endif
Is there a way to test this code, that means some CI setting
`BTITNEL_PCIE_ENABLE_HCI_DUMP`? Would the linker remove unneeded code,
if you did
static inline void btintel_pcie_hci_dump(const char *p, const void
*b, int s)
{
if (BTITNEL_PCIE_ENABLE_HCI_DUMP) {
Everything here.
}
}
> +
> +static void ipc_print_ia_ring(struct ia *ia, u16 queue_num)
> +{
> + BT_DBG("[%s] ---------------- ia ----------------",
> + queue_num == TXQ_NUM ? "TXQ" : "RXQ");
> + BT_DBG("[%s] tr-h:%02u tr-t:%02u cr-h:%02u cr-t:%02u",
> + queue_num == TXQ_NUM ? "TXQ" : "RXQ",
> + ia->tr_hia[queue_num], ia->tr_tia[queue_num],
> + ia->cr_hia[queue_num], ia->cr_tia[queue_num]);
> +}
> +
> +static void ipc_print_urbd0(struct urbd0 *urbd0, u16 index)
> +{
> + BT_DBG("[TXQ] -------------- urbd0[%u] --------------", index);
> + BT_DBG("[TXQ] tfd_index:%u num_txq:%u cmpl_cnt:%u immediate_cmpl:0x%x",
> + urbd0->tfd_index, urbd0->num_txq, urbd0->cmpl_count,
> + urbd0->immediate_cmpl);
> +}
> +
> +static void ipc_print_frbd(struct frbd *frbd, u16 index)
> +{
> + BT_DBG("[RXQ] -------------- frbd[%u] --------------", index);
> + BT_DBG("[RXQ] tag:%u addr:0x%llx", frbd->tag, frbd->addr);
> +}
> +
> +static void ipc_print_urbd1(struct urbd1 *urbd1, u16 index)
> +{
> + BT_DBG("[RXQ] -------------- urbd1[%u] --------------", index);
> + BT_DBG("[RXQ] frbd_tag:%u status: 0x%x fixed:0x%x",
> + urbd1->frbd_tag, urbd1->status, urbd1->fixed);
> +}
> +
> +/* Poll internal in microseconds */
> +#define POLL_INTERVAL 10
Please put the unit into the name: `POLL_INTERVAL_MS`. Then the comment
can also be removed as redundant.
> +
> +static int btintel_pcie_poll_bit(struct btintel_pcie_data *data, u32 offset,
> + u32 bits, u32 mask, int timeout)
Add the unit to `timeout`
> +{
> + int t = 0;
> + u32 reg;
> +
> + BT_DBG("Enter poll_bit");
Is this needed? Doesn’t Linux’ tracing framework cover this already?
> + do {
> + reg = btintel_pcie_rd_reg32(data, offset);
> + BT_DBG("CURRENT FUNC_CTRL_REG: 0x%x", reg);
> +
> + if ((reg & mask) == (bits & mask)) {
> + BT_DBG("Poll bit matched");
> + return t;
> + }
> + udelay(POLL_INTERVAL);
> + t += POLL_INTERVAL;
> + BT_DBG("Poll wait: %d", t);
Maybe elaborate, so it’s clear it’s the cummulative time. Maybe also
print `timeout` value?
> + } while (t < timeout);
> +
> + return -ETIMEDOUT;
> +}
> +
> +static struct btintel_pcie_data *btintel_pcie_get_data(struct msix_entry *entry)
> +{
> + u8 queue = entry->entry;
> + struct msix_entry *entries = entry - queue;
> +
> + return container_of(entries, struct btintel_pcie_data, msix_entries[0]);
> +}
> +
> +/* Set the doorbell for RXQ to notify the device that @index(actually index-1)
> + * is available to receive the data
> + */
> +static void btintel_pcie_set_rx_db(struct btintel_pcie_data *data, u16 index)
> +{
> + u32 val;
> +
> + val = index;
> + val |= (513 << 16);
> +
> + BT_DBG("[RXQ] Set doorbell for index: %u", index);
> + btintel_pcie_wr_reg32(data, CSR_HBUS_TARG_WRPTR, val);
> +}
> +
> +/* Update the FRBD(free buffer descriptor) with the @frbd_index and the
> + * DMA address of the free buffer.
> + */
> +static void btintel_pcie_prepare_rx(struct rxq *rxq, u16 frbd_index)
> +{
> + struct data_buf *buf;
> + struct frbd *frbd;
> +
> + /* Get the buffer of the frbd for DMA */
> + buf = &rxq->bufs[frbd_index];
> +
> + frbd = &rxq->frbds[frbd_index];
> + memset(frbd, 0, sizeof(*frbd));
> +
> + /* Update FRBD */
> + frbd->tag = frbd_index;
> + frbd->addr = buf->data_p_addr;
> + ipc_print_frbd(frbd, frbd_index);
> +}
> +
> +static int btintel_pcie_submit_rx(struct btintel_pcie_data *data)
> +{
> + u16 frbd_index;
> + struct rxq *rxq = &data->rxq;
> +
> + /* Read the frbd index from the TR_HIA(Head Index Array) for RXQ */
> + frbd_index = data->ia.tr_hia[RXQ_NUM];
> + BT_DBG("[RXQ] current frbd_index: %u", frbd_index);
> +
> + /* Make sure the index value is within the range. It shouldn't be
> + * bigger than the total count of the queue.
> + */
> + if (frbd_index > rxq->count) {
> + BT_ERR("[RXQ] RXQ out of range: (0x%x)", frbd_index);
> + return -ERANGE;
> + }
> +
> + /* Prepare for RX submit. It updates the FRBD with the address of DMA
> + * buffer
> + */
> + btintel_pcie_prepare_rx(rxq, frbd_index);
> +
> + /* Update TR_HIA with new FRBD index */
> + frbd_index = (frbd_index + 1) % rxq->count;
> + data->ia.tr_hia[RXQ_NUM] = frbd_index;
> + ipc_print_ia_ring(&data->ia, RXQ_NUM);
> +
> + /* Set the doorbell to notify the device */
> + btintel_pcie_set_rx_db(data, frbd_index);
> +
> + BT_DBG("[RXQ] rx sumbit completed");
> +
> + return 0;
> +}
> +
> +static int btintel_pcie_start_rx(struct btintel_pcie_data *data)
> +{
> + int i, ret;
> +
> + for (i = 0; i < RX_MAX_QUEUE; i++) {
> + ret = btintel_pcie_submit_rx(data);
> + if (ret) {
> + BT_ERR("[RXQ] failed to submit frbd(%d)", ret);
> + return ret;
> + }
> + }
> +
> + return 0;
> +}
> +
> +static void btintel_pcie_reset_ia(struct btintel_pcie_data *data)
> +{
> + memset(data->ia.tr_hia, 0, sizeof(u16) * NUM_QUEUES);
> + memset(data->ia.tr_tia, 0, sizeof(u16) * NUM_QUEUES);
> + memset(data->ia.cr_hia, 0, sizeof(u16) * NUM_QUEUES);
> + memset(data->ia.cr_tia, 0, sizeof(u16) * NUM_QUEUES);
> + BT_DBG("Index Arrays are reset");
> +}
> +
> +static void btintel_pcie_reset_bt(struct btintel_pcie_data *data)
> +{
> + BT_INFO("Reset BT Function ");
> + btintel_pcie_wr_reg32(data, CSR_FUNC_CTRL_REG, CSR_FUNC_CTRL_SW_RESET);
> +}
> +
> +/* This function enables BT function by setting CSR_FUNC_CTRL_MAC_INIT bit in
> + * CSR_FUNC_CTRL_REG register and wait for MSI-X with MSIX_HW_INT_CAUSES_GP0.
> + * Then the host reads firmware version from CSR_F2D_MBX and the boot stage
> + * from CSR_BOOT_STAGE_REG.
> + */
> +static int btintel_pcie_enable_bt(struct btintel_pcie_data *data)
> +{
> + int err;
> + u32 reg;
> +
> + data->gp0_received = false;
> +
> + /* Update the DMA address of CI struct to CSR */
> + btintel_pcie_wr_reg32(data, CSR_CI_ADDR_LSB_REG,
> + data->ci_p_addr & 0xffffffff);
> + btintel_pcie_wr_reg32(data, CSR_CI_ADDR_MSB_REG,
> + data->ci_p_addr >> 32);
> +
> + /* Reset the cached value of boot stage. it is updated by the msix
> + * gp0 interrupt handler.
> + */
> + data->boot_stage_cache = 0x0;
> +
> + /* Set MAC_INIT bit to start primary bootloader */
> + reg = btintel_pcie_rd_reg32(data, CSR_FUNC_CTRL_REG);
> + BT_INFO("Before: FUNC_CTRL_REG: 0x%x", reg);
> +
> + btintel_pcie_set_reg_bits(data, CSR_FUNC_CTRL_REG,
> + CSR_FUNC_CTRL_MAC_INIT);
> + BT_INFO("MAC_INIT is set");
> +
> + /* Wait until MAC_ACCESS is granted */
> + err = btintel_pcie_poll_bit(data, CSR_FUNC_CTRL_REG,
> + CSR_FUNC_CTRL_MAC_ACCESS_STS,
> + CSR_FUNC_CTRL_MAC_ACCESS_STS,
> + DEFAULT_MAC_ACCESS_TIMEOUT);
> + if (err < 0) {
> + BT_ERR("Failed to start bootloader even after %u ns",
> + DEFAULT_MAC_ACCESS_TIMEOUT);
> + return -ENODEV;
> + }
> +
> + /* MAC is ready. Enable BT FUNC */
> + btintel_pcie_set_reg_bits(data, CSR_FUNC_CTRL_REG,
> + CSR_FUNC_CTRL_FUNC_ENA |
> + CSR_FUNC_CTRL_FUNC_INIT);
> +
> + reg = btintel_pcie_rd_reg32(data, CSR_FUNC_CTRL_REG);
> + BT_INFO("After: FUNC_CTRL_REG: 0x%x", reg);
> +
> + /* wait for interrupt from the device after booting up to primary
> + * bootloader.
> + */
> + err = wait_event_timeout(data->gp0_wait_q, data->gp0_received,
> + msecs_to_jiffies(DEFAULT_INTR_TIMEOUT));
> + if (!err) {
> + BT_ERR("Failed to receive mac_init interrupt");
> + return -ETIME;
> + }
> +
> + /* Check cached boot stage is CSR_BOOT_STAGE_ROM(BIT(0)) */
> + if (~data->boot_stage_cache & CSR_BOOT_STAGE_ROM) {
> + BT_ERR("Device is not running in rom");
> + return -ENODEV;
> + }
> +
> + return 0;
> +}
> +
> +/* This function handles the MSI-X interrupt for gp0 cause(bit 0 in
> + * CSR_MSIX_HW_INT_CAUSES) which is sent for boot stage and image response.
> + */
> +static void btintel_pcie_msix_gp0_handler(struct btintel_pcie_data *data)
> +{
> + u32 reg;
> +
> + /* This interrupt is for three different causes and it is not easy to
> + * know what causes the interrupt. So, it compares each register value
> + * with cached value and update it before it wake up the queue.
> + */
> + reg = btintel_pcie_rd_reg32(data, CSR_BOOT_STAGE_REG);
> + if (reg != data->boot_stage_cache) {
> + data->boot_stage_cache = reg;
> +
> + BT_DBG("Boot Stage updated: 0x%x", reg);
> + }
> +
> + reg = btintel_pcie_rd_reg32(data, CSR_IMG_RESPONSE_REG);
> + if (reg != data->img_resp_cache) {
> + data->img_resp_cache = reg;
> +
> + BT_DBG("Image Response updated: 0x%x", reg);
> + }
> +
> + BT_DBG("---------- cached GP0 registers ----------");
> + BT_DBG("Cached Boot Stage Reg: 0x%x", data->boot_stage_cache);
> + BT_DBG("Cached Image Resp Reg: 0x%x", data->img_resp_cache);
> +
> + data->gp0_received = true;
> +
> + /* If the boot stage is OP or IML, reset IA and start RX again */
> + if (data->boot_stage_cache & CSR_BOOT_STAGE_OPFW ||
> + data->boot_stage_cache & CSR_BOOT_STAGE_IML) {
> + btintel_pcie_reset_ia(data);
> + btintel_pcie_start_rx(data);
> + }
> +
> + wake_up(&data->gp0_wait_q);
> +}
> +
> +/* This function handles the MSX-X interrupt for rx queue 0 which is for TX
> + */
> +static void btintel_pcie_msix_tx_handle(struct btintel_pcie_data *data)
> +{
> + u16 cr_tia, cr_hia;
> + struct txq *txq;
> + struct urbd0 *urbd0;
> +
> + cr_tia = data->ia.cr_tia[TXQ_NUM];
> + cr_hia = data->ia.cr_hia[TXQ_NUM];
> +
> + BT_DBG("[TXQ] cr_hia=%u cr_tia=%u", cr_hia, cr_tia);
> +
> + /* Check CR_TIA and CR_HIA for change */
> + if (cr_tia == cr_hia) {
> + BT_ERR("[TXQ] no new CD found");
> + return;
> + }
> +
> + txq = &data->txq;
> +
> + while (cr_tia != cr_hia) {
> + BT_DBG("[TXQ] wake up tx_wait_q");
> +
> + data->tx_wait_done = true;
> + wake_up(&data->tx_wait_q);
> +
> + /* Get URBD0 pointed by cr_tia */
> + urbd0 = &txq->urbd0s[cr_tia];
> + ipc_print_urbd0(urbd0, cr_tia);
> +
> + /* Make sure the completed TFD index is within the range */
> + if (urbd0->tfd_index > txq->count) {
> + BT_ERR("[TXQ] out of range: (0x%x)", urbd0->tfd_index);
> + return;
> + }
> +
> + /* Increase cr_tia */
> + cr_tia = (cr_tia + 1) % txq->count;
> + data->ia.cr_tia[TXQ_NUM] = cr_tia;
> + ipc_print_ia_ring(&data->ia, TXQ_NUM);
> + }
> +}
> +
> +static int btintel_pcie_recv_event_intel(struct hci_dev *hdev,
> + struct sk_buff *skb)
> +{
> + if (btintel_test_flag(hdev, INTEL_BOOTLOADER)) {
> + struct hci_event_hdr *hdr = (void *)skb->data;
> +
> + if (skb->len > HCI_EVENT_HDR_SIZE && hdr->evt == 0xff &&
> + hdr->plen > 0) {
> + const void *ptr = skb->data + HCI_EVENT_HDR_SIZE + 1;
> + unsigned int len = skb->len - HCI_EVENT_HDR_SIZE - 1;
> +
> + switch (skb->data[2]) {
> + case 0x02:
> + /* When switching to the operational firmware
> + * the device sends a vendor specific event
> + * indicating that the bootup completed.
> + */
> + btintel_bootup(hdev, ptr, len);
> + break;
> + case 0x06:
> + /* When the firmware loading completes the
> + * device sends out a vendor specific event
> + * indicating the result of the firmware
> + * loading.
> + */
> + btintel_secure_send_result(hdev, ptr, len);
> + break;
> + }
> + }
> + }
> +
> + return hci_recv_frame(hdev, skb);
> +}
> +
> +/* Process the received rx data
> + * It check the frame header to identify the data type and create skb
> + * and calling HCI API
> + */
> +static int btintel_pcie_hci_recv_frame(struct btintel_pcie_data *data,
> + void *buf, int count)
> +{
> + struct hci_dev *hdev = data->hdev;
> + int ret;
> + u32 pkt_type;
> + u16 plen;
> + struct sk_buff *skb;
> +
> + spin_lock(&data->hci_rx_lock);
> +
> + /* The first 4 bytes indicates the Intel PCIe specific packet type.
> + * Read the packet type here before remove it.
> + */
> + pkt_type = get_unaligned_le32(buf);
> + bt_dev_dbg(hdev, "pkt_type=%u count=%d", pkt_type, count);
> +
> + buf += BTINTEL_PCIE_HCI_TYPE_LEN;
> + count -= BTINTEL_PCIE_HCI_TYPE_LEN;
> +
> + hdev->stat.byte_rx += count;
> +
> + skb = bt_skb_alloc(count, GFP_ATOMIC);
> + if (!skb) {
> + bt_dev_err(hdev, "Failed to allocate skb for event");
> + ret = -ENOMEM;
> + goto exit_error;
> + }
> +
> + switch (pkt_type) {
> + case BTINTEL_PCIE_HCI_ACL_PKT:
> + hci_skb_pkt_type(skb) = HCI_ACLDATA_PKT;
> + memcpy(skb_put(skb, HCI_ACL_HDR_SIZE), buf, HCI_ACL_HDR_SIZE);
> + plen = hci_acl_hdr(skb)->dlen;
> + buf += HCI_ACL_HDR_SIZE;
> + break;
> + case BTINTEL_PCIE_HCI_SCO_PKT:
> + hci_skb_pkt_type(skb) = HCI_SCODATA_PKT;
> + memcpy(skb_put(skb, HCI_SCO_HDR_SIZE), buf, HCI_SCO_HDR_SIZE);
> + plen = hci_sco_hdr(skb)->dlen;
> + buf += HCI_SCO_HDR_SIZE;
> + break;
> + case BTINTEL_PCIE_HCI_EVT_PKT:
> + hci_skb_pkt_type(skb) = HCI_EVENT_PKT;
> + memcpy(skb_put(skb, HCI_EVENT_HDR_SIZE), buf,
> + HCI_EVENT_HDR_SIZE);
> + plen = hci_event_hdr(skb)->plen;
> + buf += HCI_EVENT_HDR_SIZE;
> + break;
> + default:
> + ret = -EILSEQ;
> + kfree_skb(skb);
> + goto exit_error;
> + }
> + memcpy(skb_put(skb, plen), buf, plen);
> +
> + if (pkt_type == BTINTEL_PCIE_HCI_EVT_PKT)
> + ret = btintel_pcie_recv_event_intel(hdev, skb);
> + else
> + ret = hci_recv_frame(hdev, skb);
> +
> +exit_error:
> + if (ret)
> + hdev->stat.err_rx++;
> +
> + spin_unlock(&data->hci_rx_lock);
> +
> + return ret;
> +}
> +
> +/* RX work queue */
> +static void btintel_pcie_rx_work(struct work_struct *work)
> +{
> + struct btintel_pcie_data *data = container_of(work,
> + struct btintel_pcie_data, rx_work);
> + struct sk_buff *skb;
> + int err;
> +
> + /* Process the sk_buf in queue and send to the hci layer */
> + while ((skb = skb_dequeue(&data->rx_skb_q))) {
> + err = btintel_pcie_hci_recv_frame(data, skb->data, skb->len);
> + if (err) {
> + BT_ERR("Failed to send received frame: %d", err);
> + kfree_skb(skb);
> + }
> + }
> +}
> +
> +/* create the sk_buff with data and save it to queue and start rx work
> + */
> +static int btintel_pcie_submit_rx_work(struct btintel_pcie_data *data, u8 status,
> + void *buf)
> +{
> + int ret, len;
> + struct rfh_hdr *rfh_hdr;
> + struct sk_buff *skb;
> +
> + rfh_hdr = (struct rfh_hdr *)buf;
> + btintel_pcie_hci_dump("RFH HDR", buf, sizeof(*rfh_hdr));
> +
> + len = rfh_hdr->packet_len;
> +
> + /* Remove RFH header */
> + buf += sizeof(*rfh_hdr);
> + btintel_pcie_hci_dump("RX", buf, len);
> +
> + /* Create the sk_buf with packet in the buf and save it to sk_buf queue
> + */
> + skb = alloc_skb(len, GFP_ATOMIC);
> + if (!skb) {
> + ret = -ENOMEM;
> + goto resubmit;
> + }
> +
> + /* Copy the data to skb */
> + memcpy(skb_put(skb, len), buf, len);
> +
> + /* Save the skb to rx queue */
> + skb_queue_tail(&data->rx_skb_q, skb);
> +
> + /* Calling rx_work queue to process the skb */
> + queue_work(data->workqueue, &data->rx_work);
> +
> +resubmit:
> + BT_DBG("submit next read request");
> +
> + /* submit read */
> + ret = btintel_pcie_submit_rx(data);
> +
> + return ret;
> +}
> +
> +/* This function handles the MSI-X interrupt for rx queue 1 which is for RX
> + */
> +static void btintel_pcie_msix_rx_handle(struct btintel_pcie_data *data)
> +{
> + u16 cr_hia, cr_tia;
> + struct rxq *rxq;
> + struct urbd1 *urbd1;
> + struct frbd *frbd;
> + struct data_buf *buf;
> + int ret;
> +
> + cr_hia = data->ia.cr_hia[RXQ_NUM];
> + cr_tia = data->ia.cr_tia[RXQ_NUM];
> +
> + BT_DBG("[RXQ] cr_hia=%u cr_tia=%u", cr_hia, cr_tia);
> +
> + /* Check CR_TIA and CR_HIA for change */
> + if (cr_tia == cr_hia) {
> + BT_ERR("[RXQ] no new CD found");
> + return;
> + }
> +
> + rxq = &data->rxq;
> +
> + /* The firmware sends multiple CD in a single MSIX and it needs to
> + * process all received CDs in this interrupt.
> + */
> + while (cr_tia != cr_hia) {
> + /* Get URBD1 pointed by cr_tia */
> + urbd1 = &rxq->urbd1s[cr_tia];
> + ipc_print_urbd1(urbd1, cr_tia);
> +
> + /* Get FRBD poined by urbd1->frbd_tag */
> + frbd = &rxq->frbds[urbd1->frbd_tag];
> +
> + /* Get buf from FRBD tag */
> + buf = &rxq->bufs[urbd1->frbd_tag];
> + if (!buf) {
> + BT_ERR("[RXQ] failed to get the DMA buffer for %d",
> + urbd1->frbd_tag);
> + return;
> + }
> +
> + /* prepare RX work */
> + ret = btintel_pcie_submit_rx_work(data, urbd1->status,
> + buf->data);
> + if (ret) {
> + BT_ERR("[RXQ] failed to submit rx request");
> + return;
> + }
> +
> + /* Update cr_tia */
> + cr_tia = (cr_tia + 1) % rxq->count;
> + data->ia.cr_tia[RXQ_NUM] = cr_tia;
> + ipc_print_ia_ring(&data->ia, RXQ_NUM);
> + }
> + BT_DBG("[RXQ] completed rx interrupt");
> +}
> +
> +static irqreturn_t btintel_pcie_msix_isr(int irq, void *data)
> +{
> + return IRQ_WAKE_THREAD;
> +}
> +
> +static irqreturn_t btintel_pcie_irq_msix_handler(int irq, void *dev_id)
> +{
> + struct msix_entry *entry = dev_id;
> + struct btintel_pcie_data *data = btintel_pcie_get_data(entry);
> + u32 intr_fh, intr_hw;
> +
> + BT_DBG("handling msix(irq=%d dev_id=0x%p)", irq, dev_id);
> +
> + spin_lock(&data->irq_lock);
> + intr_fh = btintel_pcie_rd_reg32(data, CSR_MSIX_FH_INT_CAUSES);
> + intr_hw = btintel_pcie_rd_reg32(data, CSR_MSIX_HW_INT_CAUSES);
> +
> + /* Clear causes registers to avoid being handling the same cause */
> + btintel_pcie_wr_reg32(data, CSR_MSIX_FH_INT_CAUSES, intr_fh);
> + btintel_pcie_wr_reg32(data, CSR_MSIX_HW_INT_CAUSES, intr_hw);
> + spin_unlock(&data->irq_lock);
> +
> + BT_DBG("intr_fh=0x%x intr_hw=0x%x", intr_fh, intr_hw);
> +
> + if (unlikely(!(intr_fh | intr_hw))) {
> + BT_DBG("Ignore interrupt, inta == 0");
> + return IRQ_NONE;
> + }
> +
> + /* This interrupt is triggered by the firmware after updating
> + * boot_stage register and image_response register
> + */
> + if (intr_hw & MSIX_HW_INT_CAUSES_GP0) {
> + BT_DBG("intr for MSIX_HW_INT_CAUSES_GP0");
> + btintel_pcie_msix_gp0_handler(data);
> + }
> +
> + /* For TX */
> + if (intr_fh & MSIX_FH_INT_CAUSES_0) {
> + BT_DBG("intr for MSIX_FH_INT_CAUSES_0");
> + btintel_pcie_msix_tx_handle(data);
> + }
> +
> + /* For RX */
> + if (intr_fh & MSIX_FH_INT_CAUSES_1) {
> + BT_DBG("intr for MSIX_FH_INT_CAUSES_1");
> + btintel_pcie_msix_rx_handle(data);
> + }
> +
> + /* TODO: Add handler for other causes */
> + /*
> + * Before sending the interrupt the HW disables it to prevent
> + * a nested interrupt. This is done by writing 1 to the corresponding
> + * bit in the mask register. After handling the interrupt, it should be
> + * re-enabled by clearing this bit. This register is defined as
> + * write 1 clear (W1C) register, meaning that it's being clear
> + * by writing 1 to the bit.
> + */
> + btintel_pcie_wr_reg32(data, CSR_MSIX_AUTOMASK_ST, BIT(entry->entry));
> +
> + return IRQ_HANDLED;
> +}
> +
> +/* This function requests the irq for msix and registers the handlers per irq.
> + * Currently, it requests only 1 irq for all interrupt causes.
> + */
> +static int btintel_pcie_setup_irq(struct btintel_pcie_data *data)
> +{
> + int err;
> + int num_irqs, i;
> +
> + BT_DBG("Initialize msix_entries...");
> + for (i = 0; i < MSIX_VEC_MAX; i++) {
> + data->msix_entries[i].entry = i;
> + BT_DBG("msix_entries[%d] vector=0x%x entry=0x%x",
> + i, data->msix_entries[i].vector,
> + data->msix_entries[i].entry);
> + }
> +
> + num_irqs = pci_enable_msix_range(data->pdev, data->msix_entries,
> + MSIX_VEC_MIN,
> + MSIX_VEC_MAX);
> + if (num_irqs < 0) {
> + BT_ERR("Failed to enable msix range (%d)", num_irqs);
> + return num_irqs;
> + }
> +
> + data->alloc_vecs = num_irqs;
> + data->msix_enabled = 1;
> + data->def_irq = 0;
> +
> + BT_DBG("Returned num_irqs=%d", num_irqs);
> + for (i = 0; i < num_irqs; i++) {
> + BT_DBG("msix_entries[%d] vector=0x%x entry=0x%x", i,
> + data->msix_entries[i].vector,
> + data->msix_entries[i].entry);
> + }
> +
> + BT_DBG("setup irq handler");
> + for (i = 0; i < data->alloc_vecs; i++) {
> + struct msix_entry *msix_entry;
> +
> + msix_entry = &data->msix_entries[i];
> +
> + err = devm_request_threaded_irq(&data->pdev->dev,
> + msix_entry->vector,
> + btintel_pcie_msix_isr,
> + btintel_pcie_irq_msix_handler,
> + IRQF_SHARED,
> + KBUILD_MODNAME,
> + msix_entry);
> + if (err) {
> + BT_ERR("Failed to allocate irq handler (%d)", err);
> + return err;
> + }
> + }
> +
> + return 0;
> +}
> +
> +struct btintel_pcie_causes_list {
> + u32 cause;
> + u32 mask_reg;
> + u8 cause_num;
> +};
> +
> +struct btintel_pcie_causes_list causes_list[] = {
> + { MSIX_FH_INT_CAUSES_0, CSR_MSIX_FH_INT_MASK, 0x00 },
> + { MSIX_FH_INT_CAUSES_1, CSR_MSIX_FH_INT_MASK, 0x01 },
> + { MSIX_HW_INT_CAUSES_GP0, CSR_MSIX_HW_INT_MASK, 0x20 },
> +};
> +
> +/* This function configures the interrupt masks for both HW_INT_CAUSES and
> + * FH_INT_CAUSES which are meaningful to us.
> + *
> + * After resetting BT function via PCIE FLR or FUNC_CTRL reset, the driver
> + * need to call this function again to configure it again since the masks
> + * are reset to 0xFFFFFFFF after reset.
> + */
> +static void btintel_pcie_config_msix(struct btintel_pcie_data *data)
> +{
> + int i;
> + int val = data->def_irq | MSIX_NON_AUTO_CLEAR_CAUSE;
> +
> + /* Set Non Auto Clear Cause */
> + for (i = 0; i < ARRAY_SIZE(causes_list); i++) {
> + btintel_pcie_wr_reg8(data,
> + CSR_MSIX_IVAR(causes_list[i].cause_num),
> + val);
> + btintel_pcie_clr_reg_bits(data,
> + causes_list[i].mask_reg,
> + causes_list[i].cause);
> + }
> +
> + /* Save the initial interrupt mask */
> + data->fh_init_mask = ~btintel_pcie_rd_reg32(data, CSR_MSIX_FH_INT_MASK);
> + data->hw_init_mask = ~btintel_pcie_rd_reg32(data, CSR_MSIX_HW_INT_MASK);
> + BT_DBG("init_mask: fh=0x%x hw=0x%x", data->fh_init_mask,
> + data->hw_init_mask);
> +}
> +
> +static int btintel_pcie_config_pcie(struct pci_dev *pdev,
> + struct btintel_pcie_data *data)
> +{
> + int err;
> +
> + err = pcim_enable_device(pdev);
> + if (err) {
> + BT_ERR("Failed to enable pci device (%d)", err);
> + return err;
> + }
> + pci_set_master(pdev);
> +
> + /* Setup DMA mask */
> + BT_DBG("Set DMA_MASK(64)");
> + err = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64));
> + if (err) {
> + BT_DBG("Set DMA_MASK(32)");
> + err = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32));
> + /* Both attempt failed */
> + if (err) {
> + BT_ERR("No suitable DMA available");
> + return err;
> + }
> + }
> +
> + /* Get BAR to access CSR */
> + err = pcim_iomap_regions(pdev, BIT(0), KBUILD_MODNAME);
> + if (err) {
> + BT_ERR("Failed to get iomap regions (%d)", err);
> + return err;
> + }
> +
> + data->base_addr = pcim_iomap_table(pdev)[0];
> + if (!data->base_addr) {
> + BT_ERR("Failed to get base address");
> + return -ENODEV;
> + }
> +
> + err = btintel_pcie_setup_irq(data);
> + if (err) {
> + BT_ERR("Failed to setup irq for msix");
> + return err;
> + }
> +
> + /* Configure MSI-X with causes list */
> + btintel_pcie_config_msix(data);
> +
> + return 0;
> +}
> +
> +static void btintel_pcie_init_ci(struct btintel_pcie_data *data,
> + struct ctx_info *ci)
> +{
> + ci->version = 0x1;
> + ci->size = sizeof(*ci);
> + ci->config = 0x0000;
> + ci->addr_cr_hia = data->ia.cr_hia_p_addr;
> + ci->addr_tr_tia = data->ia.tr_tia_p_addr;
> + ci->addr_cr_tia = data->ia.cr_tia_p_addr;
> + ci->addr_tr_hia = data->ia.tr_hia_p_addr;
> + ci->num_cr_ia = NUM_QUEUES;
> + ci->num_tr_ia = NUM_QUEUES;
> + ci->addr_urbdq0 = data->txq.urbd0s_p_addr;
> + ci->addr_tfdq = data->txq.tfds_p_addr;
> + ci->num_tfdq = data->txq.count;
> + ci->num_urbdq0 = data->txq.count;
> + ci->tfdq_db_vec = TXQ_NUM;
> + ci->urbdq0_db_vec = TXQ_NUM;
> + ci->rbd_size = RBD_SIZE_4K;
> + ci->addr_frbdq = data->rxq.frbds_p_addr;
> + ci->num_frbdq = data->rxq.count;
> + ci->frbdq_db_vec = RXQ_NUM;
> + ci->addr_urbdq1 = data->rxq.urbd1s_p_addr;
> + ci->num_urbdq1 = data->rxq.count;
> + ci->urbdq_db_vec = RXQ_NUM;
> +}
> +
> +static void btintel_pcie_free_txq_bufs(struct btintel_pcie_data *data,
> + struct txq *txq)
> +{
> + /* Free data buffers first */
> + dma_free_coherent(&data->pdev->dev, txq->count * BUFFER_SIZE,
> + txq->buf_v_addr, txq->buf_p_addr);
> + kfree(txq->bufs);
> + BT_DBG("txq buffers are freed");
> +}
> +
> +static int btintel_pcie_setup_txq_bufs(struct btintel_pcie_data *data,
> + struct txq *txq)
> +{
> + int err = 0, i;
> + struct data_buf *buf;
> +
> + if (txq->count == 0) {
> + BT_ERR("invalid parameter: txq->count");
> + err = -EINVAL;
> + goto exit_error;
> + }
> +
> + /* Allocate the same number of buffers as the descriptor */
> + txq->bufs = kmalloc_array(txq->count, sizeof(*buf), GFP_KERNEL);
> + if (!txq->bufs) {
> + err = -ENOMEM;
> + goto exit_error;
> + }
> +
> + /* Allocate full chunk of data buffer for DMA first and do indexing and
> + * initialization next, so it can be freed easily
> + */
> + txq->buf_v_addr = dma_alloc_coherent(&data->pdev->dev,
> + txq->count * BUFFER_SIZE,
> + &txq->buf_p_addr,
> + GFP_KERNEL | __GFP_NOWARN);
> + if (!txq->buf_v_addr) {
> + BT_ERR("Failed to allocate DMA buf");
> + err = -ENOMEM;
> + kfree(txq->bufs);
> + goto exit_error;
> + }
> + memset(txq->buf_v_addr, 0, txq->count * BUFFER_SIZE);
> +
> + BT_DBG("alloc bufs: p=0x%llx v=0x%p", txq->buf_p_addr, txq->buf_v_addr);
> +
> + /* Setup the allocated DMA buffer to bufs. Each data_buf should
> + * have virtual address and physical address
> + */
> + for (i = 0; i < txq->count; i++) {
> + buf = &txq->bufs[i];
> + buf->data_p_addr = txq->buf_p_addr + (i * BUFFER_SIZE);
> + buf->data = txq->buf_v_addr + (i * BUFFER_SIZE);
> + }
> +
> +exit_error:
> + return err;
> +}
> +
> +static void btintel_pcie_free_rxq_bufs(struct btintel_pcie_data *data,
> + struct rxq *rxq)
> +{
> + /* Free data buffers first */
> + dma_free_coherent(&data->pdev->dev, rxq->count * BUFFER_SIZE,
> + rxq->buf_v_addr, rxq->buf_p_addr);
> + kfree(rxq->bufs);
> + BT_DBG("rxq buffers are freed");
> +}
> +
> +static int btintel_pcie_setup_rxq_bufs(struct btintel_pcie_data *data,
> + struct rxq *rxq)
> +{
> + int err = 0, i;
> + struct data_buf *buf;
> +
> + if (rxq->count == 0) {
> + BT_ERR("invalid parameter: rxq->count");
> + err = -EINVAL;
> + goto exit_error;
> + }
> +
> + /* Allocate the same number of buffers as the descriptor */
> + rxq->bufs = kmalloc_array(rxq->count, sizeof(*buf), GFP_KERNEL);
> + if (!rxq->bufs) {
> + err = -ENOMEM;
> + goto exit_error;
> + }
> +
> + /* Allocate full chunk of data buffer for DMA first and do indexing and
> + * initialization next, so it can be freed easily
> + */
> + rxq->buf_v_addr = dma_alloc_coherent(&data->pdev->dev,
> + rxq->count * BUFFER_SIZE,
> + &rxq->buf_p_addr,
> + GFP_KERNEL | __GFP_NOWARN);
> + if (!rxq->buf_v_addr) {
> + BT_ERR("Failed to allocate DMA buf");
> + err = -ENOMEM;
> + kfree(rxq->bufs);
> + goto exit_error;
> + }
> + memset(rxq->buf_v_addr, 0, rxq->count * BUFFER_SIZE);
> +
> + BT_DBG("alloc bufs: p=0x%llx v=0x%p", rxq->buf_p_addr, rxq->buf_v_addr);
> +
> + /* Setup the allocated DMA buffer to bufs. Each data_buf should
> + * have virtual address and physical address
> + */
> + for (i = 0; i < rxq->count; i++) {
> + buf = &rxq->bufs[i];
> + buf->data_p_addr = rxq->buf_p_addr + (i * BUFFER_SIZE);
> + buf->data = rxq->buf_v_addr + (i * BUFFER_SIZE);
> + }
> +
> +exit_error:
> +
> + return err;
> +}
> +
> +static void btintel_pcie_setup_ia(struct btintel_pcie_data *data,
> + dma_addr_t p_addr, void *v_addr,
> + struct ia *ia)
> +{
> + /* TR Head Index Array */
> + ia->tr_hia_p_addr = p_addr;
> + ia->tr_hia = v_addr;
> +
> + /* TR Tail Index Array */
> + ia->tr_tia_p_addr = p_addr + sizeof(u16) * NUM_QUEUES;
> + ia->tr_tia = v_addr + sizeof(u16) * NUM_QUEUES;
> +
> + /* CR Head index Array */
> + ia->cr_hia_p_addr = p_addr + (sizeof(u16) * NUM_QUEUES * 2);
> + ia->cr_hia = v_addr + (sizeof(u16) * NUM_QUEUES * 2);
> +
> + /* CR Tail Index Array */
> + ia->cr_tia_p_addr = p_addr + (sizeof(u16) * NUM_QUEUES * 3);
> + ia->cr_tia = v_addr + (sizeof(u16) * NUM_QUEUES * 3);
> +}
> +
> +static void btintel_pcie_free(struct btintel_pcie_data *data)
> +{
> + btintel_pcie_free_rxq_bufs(data, &data->rxq);
> + btintel_pcie_free_txq_bufs(data, &data->txq);
> +
> + dma_pool_free(data->dma_pool, data->dma_v_addr, data->dma_p_addr);
> + dma_pool_destroy(data->dma_pool);
> + BT_DBG("DMA memory is freed");
> +}
> +
> +/* Allocate tx and rx queues, any related data structures and buffers.
> + */
> +static int btintel_pcie_alloc(struct btintel_pcie_data *data)
> +{
> + int err = 0;
> + size_t total;
> + dma_addr_t p_addr;
> + void *v_addr;
> +
> + /* Allocate the chunk of DMA memory for descriptors, index array, and
> + * context information, instead of allocating individually.
> + * The DMA memory for data buffer is allocated while setting up the
> + * each queue.
> + *
> + * Total size is sum of the following
> + * + size of TFD * Number of descriptors in queue
> + * + size of URBD0 * Number of descriptors in queue
> + * + size of FRBD * Number of descriptors in queue
> + * + size of URBD1 * Number of descriptors in queue
> + * + size of index * Number of queues(2) * type of index array(4)
> + * + size of context information
> + */
> + total = (sizeof(struct tfd) + sizeof(struct urbd0) + sizeof(struct frbd)
> + + sizeof(struct urbd1)) * DESCS_COUNT;
> +
> + /* Add the sum of size of index array and size of ci struct */
> + total += (sizeof(u16) * NUM_QUEUES * 4) + sizeof(struct ctx_info);
> +
> + /* Allocate DMA Pool */
> + data->dma_pool = dma_pool_create(KBUILD_MODNAME, &data->pdev->dev,
> + total, DMA_POOL_ALIGNMENT, 0);
> + if (!data->dma_pool) {
> + BT_ERR("Failed to allocate dma pool for queues");
> + err = -ENOMEM;
> + goto exit_error;
> + }
> +
> + v_addr = dma_pool_zalloc(data->dma_pool, GFP_KERNEL | __GFP_NOWARN,
> + &p_addr);
> + if (!v_addr) {
> + BT_ERR("Failed to alloc dma memory for queues");
> + dma_pool_destroy(data->dma_pool);
> + err = -ENOMEM;
> + goto exit_error;
> + }
> +
> + data->dma_p_addr = p_addr;
> + data->dma_v_addr = v_addr;
> +
> + BT_DBG("dma pool: p_addr=0x%llx v_addr=0x%p", p_addr, v_addr);
> +
> + /* Setup descriptor count */
> + data->txq.count = DESCS_COUNT;
> + data->rxq.count = DESCS_COUNT;
> +
> + /* Setup tfds */
> + data->txq.tfds_p_addr = p_addr;
> + data->txq.tfds = v_addr;
> +
> + p_addr += (sizeof(struct tfd) * DESCS_COUNT);
> + v_addr += (sizeof(struct tfd) * DESCS_COUNT);
> +
> + /* Setup urbd0 */
> + data->txq.urbd0s_p_addr = p_addr;
> + data->txq.urbd0s = v_addr;
> +
> + p_addr += (sizeof(struct urbd0) * DESCS_COUNT);
> + v_addr += (sizeof(struct urbd0) * DESCS_COUNT);
> +
> + /* Setup frbd */
> + data->rxq.frbds_p_addr = p_addr;
> + data->rxq.frbds = v_addr;
> +
> + p_addr += (sizeof(struct frbd) * DESCS_COUNT);
> + v_addr += (sizeof(struct frbd) * DESCS_COUNT);
> +
> + /* Setup urbd1 */
> + data->rxq.urbd1s_p_addr = p_addr;
> + data->rxq.urbd1s = v_addr;
> +
> + p_addr += (sizeof(struct urbd1) * DESCS_COUNT);
> + v_addr += (sizeof(struct urbd1) * DESCS_COUNT);
> +
> + /* Setup data buffers for txq */
> + err = btintel_pcie_setup_txq_bufs(data, &data->txq);
> + if (err) {
> + BT_ERR("Failed to setup txq buffers: %d", err);
> + goto exit_error_pool;
> + }
> +
> + /* Setup data buffers for rxq */
> + err = btintel_pcie_setup_rxq_bufs(data, &data->rxq);
> + if (err) {
> + BT_ERR("Failed to allocate rxq buffers: %d", err);
> + goto exit_error_txq;
> + }
> +
> + /* Setup Index Array */
> + btintel_pcie_setup_ia(data, p_addr, v_addr, &data->ia);
> +
> + /* Setup Context Information */
> + p_addr += sizeof(u16) * NUM_QUEUES * 4;
> + v_addr += sizeof(u16) * NUM_QUEUES * 4;
> +
> + data->ci = v_addr;
> + data->ci_p_addr = p_addr;
> +
> + /* Initialize the CI */
> + btintel_pcie_init_ci(data, data->ci);
> +
> + return 0;
> +
> +exit_error_txq:
> + btintel_pcie_free_txq_bufs(data, &data->txq);
> +exit_error_pool:
> + dma_pool_free(data->dma_pool, data->dma_v_addr, data->dma_p_addr);
> + dma_pool_destroy(data->dma_pool);
> +exit_error:
> + return err;
> +}
> +
> +static void btintel_pcie_release_hdev(struct btintel_pcie_data *data)
> +{
> + struct hci_dev *hdev;
> +
> + hdev = data->hdev;
> + if (hdev) {
> + hci_unregister_dev(hdev);
> + hci_free_dev(hdev);
> + }
> + data->hdev = NULL;
> +}
> +
> +static int btintel_pcie_setup_hdev(struct btintel_pcie_data *data)
> +{
> + /* TODO: initialize hdev and assign the callbacks to hdev */
> + return -ENODEV;
> +}
> +
> +static int btintel_pcie_probe(struct pci_dev *pdev,
> + const struct pci_device_id *ent)
> +{
> + int err;
> + struct btintel_pcie_data *data;
> +
> + if (!pdev)
> + return -ENODEV;
> +
> + data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
> + if (!data)
> + return -ENOMEM;
> +
> + /* initialize the btintel_pcie data struct */
> + data->pdev = pdev;
> +
> + spin_lock_init(&data->irq_lock);
> + spin_lock_init(&data->hci_rx_lock);
> +
> + init_waitqueue_head(&data->gp0_wait_q);
> + data->gp0_received = false;
> +
> + init_waitqueue_head(&data->tx_wait_q);
> + data->tx_wait_done = false;
> +
> + data->workqueue = alloc_ordered_workqueue(KBUILD_MODNAME, WQ_HIGHPRI);
> + if (!data->workqueue) {
> + BT_ERR("Failed to create workqueue");
> + return -ENOMEM;
> + }
> + skb_queue_head_init(&data->rx_skb_q);
> + INIT_WORK(&data->rx_work, btintel_pcie_rx_work);
> +
> + data->boot_stage_cache = 0x00;
> + data->img_resp_cache = 0x00;
> +
> + /* PCIe specific all to configure it for this device includes
> + * enabling pice device, setting master, reading BAR[0], configuring
> + * MSIx, setting DMA mask, and save the driver data.
> + */
> + err = btintel_pcie_config_pcie(pdev, data);
> + if (err) {
> + BT_ERR("Failed to config pcie (%d)", err);
> + goto exit_error;
> + }
> +
> + /* Set driver data for this PCI device */
> + pci_set_drvdata(pdev, data);
> +
> + /* allocate the IPC struct */
> + err = btintel_pcie_alloc(data);
> + if (err) {
> + BT_ERR("Failed to allocate queues(%d)", err);
> + goto exit_error;
> + }
> +
> + /* Enable BT function */
> + err = btintel_pcie_enable_bt(data);
> + if (err) {
> + BT_ERR("Failed to start bluetooth device(%d)", err);
> + goto exit_error;
> + }
> +
> + /* CNV information (CNVi and CNVr) is in CSR */
> + data->cnvi = btintel_pcie_rd_reg32(data, CSR_HW_REV_REG);
> + BT_DBG("cnvi: 0x%08x", data->cnvi);
> +
> + data->cnvr = btintel_pcie_rd_reg32(data, CSR_RF_ID_REG);
> + BT_DBG("cnvr: 0x%08x", data->cnvr);
> +
> + err = btintel_pcie_start_rx(data);
> + if (err) {
> + BT_ERR("Failed to start rx (%d)", err);
> + goto exit_error;
> + }
> +
> + err = btintel_pcie_setup_hdev(data);
> + if (err) {
> + BT_ERR("Failed to setup HCI module");
> + goto exit_error;
> + }
> +
> + return 0;
> +
> +exit_error:
> + /* reset device before leave */
> + btintel_pcie_reset_bt(data);
> +
> + /* clear bus mastering */
> + pci_clear_master(pdev);
> +
> + /* Unset driver data for PCI device */
> + pci_set_drvdata(pdev, NULL);
> +
> + return err;
> +}
> +
> +static void btintel_pcie_remove(struct pci_dev *pdev)
> +{
> + struct btintel_pcie_data *data;
> +
> + if (!pdev) {
> + BT_ERR("Invalid parameter: pdev");
> + return;
> + }
> +
> + data = pci_get_drvdata(pdev);
> + if (!data) {
> + BT_ERR("data is empty");
> + return;
> + }
> +
> + btintel_pcie_release_hdev(data);
> +
> + flush_work(&data->rx_work);
> +
> + destroy_workqueue(data->workqueue);
> +
> + btintel_pcie_free(data);
> +
> + /* reset device before leave */
> + btintel_pcie_reset_bt(data);
> +
> + /* clear bus mastering */
> + pci_clear_master(pdev);
> +
> + /* Unset driver data for PCI device */
> + pci_set_drvdata(pdev, NULL);
> +}
> +
> +#ifdef CONFIG_PM
> +static int btintel_pcie_suspend(struct device *dev)
> +{
> + /* TODO: Add support suspend */
> + return 0;
> +}
> +
> +static int btintel_pcie_resume(struct device *dev)
> +{
> + /* TODO: Add support resume */
> + return 0;
> +}
> +
> +static SIMPLE_DEV_PM_OPS(btintel_pcie_pm_ops, btintel_pcie_suspend,
> + btintel_pcie_resume);
> +#endif /* CONFIG_PM */
> +
> +static struct pci_driver btintel_pcie_driver = {
> + .name = KBUILD_MODNAME,
> + .id_table = btintel_pcie_table,
> + .probe = btintel_pcie_probe,
> + .remove = btintel_pcie_remove,
> +#ifdef CONFIG_PM
> + .driver.pm = &btintel_pcie_pm_ops,
> +#endif /* CONFIG_PM */
> +};
> +module_pci_driver(btintel_pcie_driver);
> +
> +MODULE_AUTHOR("Tedd Ho-Jeong An <tedd.an@intel.com>");
> +MODULE_DESCRIPTION("Intel Bluetooth PCIe transport driver ver " VERSION);
> +MODULE_VERSION(VERSION);
> +MODULE_LICENSE("GPL");
> diff --git a/drivers/bluetooth/btintel_pcie.h b/drivers/bluetooth/btintel_pcie.h
> new file mode 100644
> index 000000000000..1554964686bd
> --- /dev/null
> +++ b/drivers/bluetooth/btintel_pcie.h
> @@ -0,0 +1,449 @@
> +/* SPDX-License-Identifier: GPL-2.0-or-later */
> +/*
> + * Intel Bluetooth PCIE driver
> + *
> + * Copyright (C) 2017 Intel Corporation. All rights reserved.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License version
> + * 2 as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Copyright (C) 2022 Intel Corporation
Ditto.
> + *
> + * Intel Bluetooth Driver for PCIE interface.
> + */
> +
> +/* Control and Status Register(CSR) */
> +#define CSR_BASE (0x000)
> +#define CSR_FUNC_CTRL_REG (CSR_BASE + 0x024)
> +#define CSR_HW_REV_REG (CSR_BASE + 0x028)
> +#define CSR_RF_ID_REG (CSR_BASE + 0x09C)
> +#define CSR_BOOT_STAGE_REG (CSR_BASE + 0x108)
> +#define CSR_CI_ADDR_LSB_REG (CSR_BASE + 0x118)
> +#define CSR_CI_ADDR_MSB_REG (CSR_BASE + 0x11C)
> +#define CSR_IMG_RESPONSE_REG (CSR_BASE + 0x12C)
> +#define CSR_HBUS_TARG_WRPTR (CSR_BASE + 0x460)
> +
> +/* CSR Function Control Register */
> +#define CSR_FUNC_CTRL_FUNC_ENA (BIT(0))
> +#define CSR_FUNC_CTRL_MAC_INIT (BIT(6))
> +#define CSR_FUNC_CTRL_FUNC_INIT (BIT(7))
> +#define CSR_FUNC_CTRL_MAC_ACCESS_STS (BIT(20))
> +#define CSR_FUNC_CTRL_SW_RESET (BIT(31))
> +
> +/* Value for CSR_BOOT_STAGE register */
> +#define CSR_BOOT_STAGE_ROM (BIT(0))
> +#define CSR_BOOT_STAGE_IML (BIT(1))
> +#define CSR_BOOT_STAGE_OPFW (BIT(2))
> +#define CSR_BOOT_STAGE_ROM_LOCKDOWN (BIT(10))
> +#define CSR_BOOT_STAGE_IML_LOCKDOWN (BIT(11))
> +#define CSR_BOOT_STAGE_MAC_ACCESS_ON (BIT(16))
> +#define CSR_BOOT_STAGE_ALIVE (BIT(23))
> +
> +/* Registers for MSIX */
> +#define CSR_MSIX_BASE (0x2000)
> +#define CSR_MSIX_FH_INT_CAUSES (CSR_MSIX_BASE + 0x0800)
> +#define CSR_MSIX_FH_INT_MASK (CSR_MSIX_BASE + 0x0804)
> +#define CSR_MSIX_HW_INT_CAUSES (CSR_MSIX_BASE + 0x0808)
> +#define CSR_MSIX_HW_INT_MASK (CSR_MSIX_BASE + 0x080C)
> +#define CSR_MSIX_AUTOMASK_ST (CSR_MSIX_BASE + 0x0810)
> +#define CSR_MSIX_AUTOMASK_EN (CSR_MSIX_BASE + 0x0814)
> +#define CSR_MSIX_IVAR_BASE (CSR_MSIX_BASE + 0x0880)
> +#define CSR_MSIX_IVAR(cause) (CSR_MSIX_IVAR_BASE + (cause))
> +
> +/* Causes for the FH register interrupts */
> +enum msix_fh_int_causes {
> + MSIX_FH_INT_CAUSES_0 = BIT(0), /* cause 0 */
> + MSIX_FH_INT_CAUSES_1 = BIT(1), /* cause 1 */
> +};
> +
> +/* Causes for the HW register interrupts */
> +enum msix_hw_int_causes {
> + MSIX_HW_INT_CAUSES_GP0 = BIT(0), /* cause 32 */
> +};
> +
> +#define MSIX_NON_AUTO_CLEAR_CAUSE BIT(7)
> +
> +/* Minimum and Maximum number of MSIx Vector
> + * Intel Bluetooth PCIe support only 1 vector
> + */
> +#define MSIX_VEC_MAX 1
> +#define MSIX_VEC_MIN 1
> +
> +/* Default Poll time for MAC access during init*/
Missing space at the end.
> +#define DEFAULT_MAC_ACCESS_TIMEOUT 200000
Please specify the unit in the name.
> +
> +/* Default interrupt timeout in msec */
> +#define DEFAULT_INTR_TIMEOUT 3000
Ditto.
> +
> +/* The number of descriptors in TX/RX queues */
> +#define DESCS_COUNT 16
> +
> +/* Number of Queue for TX and RX
> + * It indicates the index of the IA(Index Array)
> + */
> +enum {
> + TXQ_NUM = 0,
> + RXQ_NUM = 1,
> + NUM_QUEUES = 2,
> +};
> +
> +/* The size of DMA buffer for TX and RX */
> +#define BUFFER_SIZE 4096
Is that bytes?
> +
> +/* DMA allocation alignment */
> +#define DMA_POOL_ALIGNMENT 256
> +
> +/* TX wait time (jiffies) */
> +#define TX_WAIT_TIMEOUT 500
Please add the unit to the name.
> +
> +/* Number of pending RX requests for downlink */
> +#define RX_MAX_QUEUE 6
> +
> +/* Enum for RBD buffer size mappting */
> +enum {
> + RBD_SIZE_1K = 0x1,
> + RBD_SIZE_2K = 0x2,
> + RBD_SIZE_4K = 0x4,
> + RBD_SIZE_8K = 0x8,
> + RBD_SIZE_12K = 0x9,
> + RBD_SIZE_16K = 0xA,
> + RBD_SIZE_20K = 0xB,
> + RBD_SIZE_24K = 0xC,
> + RBD_SIZE_28K = 0xD,
> + RBD_SIZE_32K = 0xE,
> +};
> +
> +/*
> + * Struct for Context Information (v2)
> + *
> + * All members are write-only for host and read-only for device.
> + *
> + * @version: Version of context information
> + * @size: Size of context information
> + * @config: Config with which host wants peripheral to execute
> + * Subset of capability register published by device
> + * @addr_tr_hia: Address of TR Head Index Array
> + * @addr_tr_tia: Address of TR Tail Index Array
> + * @addr_cr_hia: Address of CR Head Index Array
> + * @addr_cr_tia: Address of CR Tail Index Array
> + * @num_tr_ia: Number of entries in TR Index Arrays
> + * @num_cr_ia: Number of entries in CR Index Arrays
> + * @rbd_siz: RBD Size { 0x4=4K }
> + * @addr_tfdq: Address of TFD Queue(tx)
> + * @addr_urbdq0: Address of URBD Queue(tx)
> + * @num_tfdq: Number of TFD in TFD Queue(tx)
> + * @num_urbdq0: Number of URBD in URBD Queue(tx)
> + * @tfdq_db_vec: Queue number of TFD
> + * @urbdq0_db_vec: Queue number of URBD
> + * @addr_frbdq: Address of FRBD Queue(rx)
> + * @addr_urbdq1: Address of URBD Queue(rx)
> + * @num_frbdq: Number of FRBD in FRBD Queue(rx)
> + * @frbdq_db_vec: Queue number of FRBD
> + * @num_urbdq1: Number of URBD in URBD Queue(rx)
> + * @urbdq_db_vec: Queue number of URBDQ1
> + * @tr_msi_vec: Transfer Ring MSI Vector
> + * @cr_msi_vec: Completion Ring MSI Vector
> + * @dbgc_addr: DBGC first fragmemt address
> + * @dbgc_size: DBGC buffer size
> + * @early_enable: Enarly debug enable
Early
> + * @dbg_output_mode: Debug output mode
> + * Bit[4] DBGC O/P { 0=SRAM, 1=DRAM(not relevant for NPK) }
> + * Bit[5] DBGC I/P { 0=BDBG, 1=DBGI }
> + * Bits[6:7] DBGI O/P(relevant if bit[5] = 1)
> + * 0=BT DBGC, 1=WiFi DBGC, 2=NPK }
> + * @dbg_preset: Debug preset
> + * @ext_addr: Address of context information extension
> + * @ext_size: Size of context information part
> + *
> + * Total 38 DWords
> + *
> + */
> +struct ctx_info {
> + u16 version;
> + u16 size;
> + u32 config;
> + u32 reserved_dw02;
> + u32 reserved_dw03;
> + u64 addr_tr_hia;
> + u64 addr_tr_tia;
> + u64 addr_cr_hia;
> + u64 addr_cr_tia;
> + u16 num_tr_ia;
> + u16 num_cr_ia;
> + u32 rbd_size:4,
> + reserved_dw13:28;
> + u64 addr_tfdq;
> + u64 addr_urbdq0;
> + u16 num_tfdq;
> + u16 num_urbdq0;
> + u16 tfdq_db_vec;
> + u16 urbdq0_db_vec;
> + u64 addr_frbdq;
> + u64 addr_urbdq1;
> + u16 num_frbdq;
> + u16 frbdq_db_vec;
> + u16 num_urbdq1;
> + u16 urbdq_db_vec;
> + u16 tr_msi_vec;
> + u16 cr_msi_vec;
> + u32 reserved_dw27;
> + u64 dbgc_addr;
> + u32 dbgc_size;
> + u32 early_enable:1,
> + reserved_dw31:3,
> + dbg_output_mode:4,
> + dbg_preset:8,
> + reserved2_dw31:16;
> + u64 ext_addr;
> + u32 ext_size;
> + u32 test_param;
> + u32 reserved_dw36;
> + u32 reserved_dw37;
> +} __packed;
> +
> +/* Transfer Descriptor for TX
> + * @type: Not in use. Set to 0x0
> + * @size: Size of data in the buffer
> + * @addr: DMA Address of buffer
> + */
> +struct tfd {
> + u8 type;
> + u16 size;
> + u8 reserved;
> + u64 addr;
> + u32 reserved1;
> +} __packed;
> +
> +/* URB Descriptor for TX
> + * @tfd_index: Index of TFD in TFDQ + 1
> + * @num_txq: Queue index of TFD Queue
> + * @cmpl_count: Completion count. Always 0x01
> + * @immediate_cmpl: Immediate completion flag: Always 0x01
> + */
> +struct urbd0 {
> + u32 tfd_index:16,
> + num_txq:8,
> + cmpl_count:4,
> + reserved:3,
> + immediate_cmpl:1;
> +} __packed;
> +
> +/* FRB Descriptor for RX
> + * @tag: RX buffer tag (index of RX buffer queue)
> + * @addr: Address of buffer
> + */
> +struct frbd {
> + u32 tag:16,
> + reserved:16;
> + u32 reserved2;
> + u64 addr;
> +} __packed;
> +
> +/* URB Descriptor for RX
> + * @frbd_tag: Tag from FRBD
> + * @status: Status
> + */
> +struct urbd1 {
> + u32 frbd_tag:16,
> + status:1,
> + reserved:14,
> + fixed:1;
> +} __packed;
> +
> +/* RFH header in RX packet
> + * @packet_len: Length of the data in the buffer
> + * @rxq: RX Queue number
> + * @cmd_id: Command ID. Not in Use
> + */
> +struct rfh_hdr {
> + u64 packet_len:16,
> + rxq:6,
> + reserved:10,
> + cmd_id:16,
> + reserved1:16;
> +} __packed;
> +
> +/* Internal data buffer
> + * @data: pointer to the data buffer
> + * @p_addr: physical address of data buffer
> + */
> +struct data_buf {
> + u8 *data;
> + dma_addr_t data_p_addr;
> +};
> +
> +/* Index Array */
> +struct ia {
> + dma_addr_t tr_hia_p_addr;
> + u16 *tr_hia;
> + dma_addr_t tr_tia_p_addr;
> + u16 *tr_tia;
> + dma_addr_t cr_hia_p_addr;
> + u16 *cr_hia;
> + dma_addr_t cr_tia_p_addr;
> + u16 *cr_tia;
> +};
> +
> +/* Structure for TX Queue
> + * @count: Number of descriptors
> + * @tfds: Array of TFD
> + * @urbd0s: Array of URBD0
> + * @buf: Array of data_buf structure
> + */
> +struct txq {
> + u16 count;
> +
> + dma_addr_t tfds_p_addr;
> + struct tfd *tfds;
> +
> + dma_addr_t urbd0s_p_addr;
> + struct urbd0 *urbd0s;
> +
> + dma_addr_t buf_p_addr;
> + void *buf_v_addr;
> + struct data_buf *bufs;
> +};
> +
> +/* Structure for RX Queue
> + * @count: Number of descriptors
> + * @frbds: Array of FRBD
> + * @urbd1s: Array of URBD1
> + * @buf: Array of data_buf structure
> + */
> +struct rxq {
> + u16 count;
> +
> + dma_addr_t frbds_p_addr;
> + struct frbd *frbds;
> +
> + dma_addr_t urbd1s_p_addr;
> + struct urbd1 *urbd1s;
> +
> + dma_addr_t buf_p_addr;
> + void *buf_v_addr;
> + struct data_buf *bufs;
> +};
> +
> +/* struct btintel_pcie_data
> + * @pdev: pci device
> + * @hdev: hdev device
> + * @flags: driver state
> + * @irq_lock: spinlock for MSIX
> + * @hci_rx_lock: spinlock for HCI RX flow
> + * @base_addr: pci base address (from BAR)
> + * @msix_entries: array of MSIX entries
> + * @msix_enabled: true if MSIX is enabled;
> + * @alloc_vecs: number of interrupt vectors allocated
> + * @def_irq: default irq for all causes
> + * @fh_init_mask: initial unmasked rxq causes
> + * @hw_init_mask: initial unmaksed hw causes
> + * @boot_stage_cache: cached value of boot stage register
> + * @img_resp_cache: cached value of image response register
> + * @cnvi: CNVi register value
> + * @cnvr: CNVr register value
> + * @gp0_received: condition for gp0 interrupt
> + * @gp0_wait_q: wait_q for gp0 interrupt
> + * @tx_wait_done: condition for tx interrupt
> + * @tx_wait_q: wait_q for tx interrupt
> + * @workqueue: workqueue for RX work
> + * @rx_skb_q: SKB queue for RX packet
> + * @rx_work: RX work struct to process the RX packet in @rx_skb_q
> + * @dma_pool: DMA pool for descriptors, index array and ci
> + * @dma_p_addr: DMA address for pool
> + * @dma_v_addr: address of pool
> + * @ci_p_addr: DMA address for CI struct
> + * @ci: CI struct
> + * @ia: Index Array struct
> + * @txq: TX Queue struct
> + * @rxq: RX Queue struct
> + */
> +struct btintel_pcie_data {
> + struct pci_dev *pdev;
> + struct hci_dev *hdev;
> +
> + unsigned long flags;
> + /* lock used in MSIX interrupt */
> + spinlock_t irq_lock;
> + /* lock to serialize rx events */
> + spinlock_t hci_rx_lock;
> +
> + void __iomem *base_addr;
> +
> + struct msix_entry msix_entries[MSIX_VEC_MAX];
> + bool msix_enabled;
> + u32 alloc_vecs;
> + u32 def_irq;
> +
> + u32 fh_init_mask;
> + u32 hw_init_mask;
> +
> + u32 boot_stage_cache;
> + u32 img_resp_cache;
> +
> + u32 cnvi;
> + u32 cnvr;
> +
> + bool gp0_received;
> + wait_queue_head_t gp0_wait_q;
> +
> + bool tx_wait_done;
> + wait_queue_head_t tx_wait_q;
> +
> + struct workqueue_struct *workqueue;
> + struct sk_buff_head rx_skb_q;
> + struct work_struct rx_work;
> +
> + struct dma_pool *dma_pool;
> + dma_addr_t dma_p_addr;
> + void *dma_v_addr;
> +
> + dma_addr_t ci_p_addr;
> + struct ctx_info *ci;
> + struct ia ia;
> + struct txq txq;
> + struct rxq rxq;
> +};
> +
> +static inline u32 btintel_pcie_rd_reg32(struct btintel_pcie_data *data,
> + u32 offset)
> +{
> + return ioread32(data->base_addr + offset);
> +}
> +
> +static inline void btintel_pcie_wr_reg8(struct btintel_pcie_data *data,
> + u32 offset, u8 val)
> +{
> + iowrite8(val, data->base_addr + offset);
> +}
> +
> +static inline void btintel_pcie_wr_reg32(struct btintel_pcie_data *data,
> + u32 offset, u32 val)
> +{
> + iowrite32(val, data->base_addr + offset);
> +}
> +
> +static inline void btintel_pcie_set_reg_bits(struct btintel_pcie_data *data,
> + u32 offset, u32 bits)
> +{
> + u32 r;
> +
> + r = ioread32(data->base_addr + offset);
> + r |= bits;
> + iowrite32(r, data->base_addr + offset);
> +}
> +
> +static inline void btintel_pcie_clr_reg_bits(struct btintel_pcie_data *data,
> + u32 offset, u32 bits)
> +{
> + u32 r;
> +
> + r = ioread32(data->base_addr + offset);
> + r &= ~bits;
> + iowrite32(r, data->base_addr + offset);
> +}
Kind regards,
Paul
^ permalink raw reply [flat|nested] 16+ messages in thread* RE: [PATCH v1 2/3] Bluetooth: btintel_pcie: Add support for PCIE transport
2024-03-28 12:24 ` Paul Menzel
@ 2024-05-07 13:34 ` K, Kiran
2024-05-07 20:28 ` Luiz Augusto von Dentz
0 siblings, 1 reply; 16+ messages in thread
From: K, Kiran @ 2024-05-07 13:34 UTC (permalink / raw)
To: Paul Menzel, Von Dentz, Luiz
Cc: linux-bluetooth@vger.kernel.org, Srivatsa, Ravishankar,
Tumkur Narayan, Chethan, An, Tedd, linux-pci@vger.kernel.org
Hi Paul,
Appreciate your comments :).
> -----Original Message-----
> From: Paul Menzel <pmenzel@molgen.mpg.de>
> Sent: Thursday, March 28, 2024 5:55 PM
> To: K, Kiran <kiran.k@intel.com>
> Cc: linux-bluetooth@vger.kernel.org; Srivatsa, Ravishankar
> <ravishankar.srivatsa@intel.com>; Tumkur Narayan, Chethan
> <chethan.tumkur.narayan@intel.com>; An, Tedd <tedd.an@intel.com>; linux-
> pci@vger.kernel.org
> Subject: Re: [PATCH v1 2/3] Bluetooth: btintel_pcie: Add support for PCIE
> transport
>
> Dear Tedd, dear Kiran,
>
>
> Thank you for the patch. What a diffstat. ;-) Nice work.
>
> Am 28.03.24 um 12:19 schrieb Kiran K:
> > From: Tedd Ho-Jeong An <tedd.an@intel.com>
> >
> > Add initial code to support Intel bluetooth devices based on PICE
> > transport. This patch allocates memory for buffers, internal structures,
> > initializes interrupts for TX & RX and initializes PCIE device.
>
> For a 1782 diffstat this is quite terse. Could you elaborate?
>
> Also, it’d be great if you mentioned the datasheet, and how you tested
> this. Maybe even paste the new log messages.
>
Datasheet details are internal to Intel. Sorry I can't provide those details. But surely I will add kernel logs and output of hciconfig -a.
> Also how well does the driver perform? What tools did you run to verify
> the correctness und the “speed”?
This driver has been tested on silicon (BT Filmore Peak2). Not sure of any tools to test the speed. Pls suggest if any. I will run the same and share the data.
>
> > Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
> > Co-developed-by: Kiran K <kiran.k@intel.com>
> > Signed-off-by: Kiran K <kiran.k@intel.com>
> > ---
> > drivers/bluetooth/Kconfig | 14 +
> > drivers/bluetooth/Makefile | 1 +
> > drivers/bluetooth/btintel.h | 2 +-
> > drivers/bluetooth/btintel_pcie.c | 1317
> ++++++++++++++++++++++++++++++
> > drivers/bluetooth/btintel_pcie.h | 449 ++++++++++
> > 5 files changed, 1782 insertions(+), 1 deletion(-)
> > create mode 100644 drivers/bluetooth/btintel_pcie.c
> > create mode 100644 drivers/bluetooth/btintel_pcie.h
>
> Should an entry be added to `MAINTAINERS`? It’d be good to mention in
> the commit message, who the maintainer is.
Individual files under drivers/bluetooth/ are not updated in MAINTAINERS. There is "F: drivers/bluetooth/" entry present. I haven't added any files in the past.
@Von Dentz, Luiz - Any comments here ?
>
> >
> > diff --git a/drivers/bluetooth/Kconfig b/drivers/bluetooth/Kconfig
> > index bc211c324206..387f7b14461d 100644
> > --- a/drivers/bluetooth/Kconfig
> > +++ b/drivers/bluetooth/Kconfig
> > @@ -23,6 +23,20 @@ config BT_MTK
> > tristate
> > select FW_LOADER
> >
> > +config BT_INTEL_PCIE
> > + tristate "Intel Bluetooth transport driver for PCIe"
>
> In the commit message summary you spell it PCIE. Please be consistent.
>
Ack.
> > + depends on PCI
> > + select BT_INTEL
> > + select FW_LOADER
> > + default y
> > + help
> > + Intel Bluetooth transport driver for PCIe.
> > + This driver is required if you want to use Intel Bluetooth device
> > + with PCIe interface.
> > +
> > + Say Y here to compiler support for Intel Bluetooth PCIe device into
> > + the kernel or say M to compile it as module (btintel_pcie)
> > +
> > config BT_HCIBTUSB
> > tristate "HCI USB driver"
> > depends on USB
> > diff --git a/drivers/bluetooth/Makefile b/drivers/bluetooth/Makefile
> > index 7a5967e9ac48..0730d6684d1a 100644
> > --- a/drivers/bluetooth/Makefile
> > +++ b/drivers/bluetooth/Makefile
> > @@ -17,6 +17,7 @@ obj-$(CONFIG_BT_HCIBTUSB) += btusb.o
> > obj-$(CONFIG_BT_HCIBTSDIO) += btsdio.o
> >
> > obj-$(CONFIG_BT_INTEL) += btintel.o
> > +obj-$(CONFIG_BT_INTEL_PCIE) += btintel_pcie.o btintel.o
> > obj-$(CONFIG_BT_ATH3K) += ath3k.o
> > obj-$(CONFIG_BT_MRVL) += btmrvl.o
> > obj-$(CONFIG_BT_MRVL_SDIO) += btmrvl_sdio.o
> > diff --git a/drivers/bluetooth/btintel.h b/drivers/bluetooth/btintel.h
> > index 1462a57420a0..5d4685b5c1fa 100644
> > --- a/drivers/bluetooth/btintel.h
> > +++ b/drivers/bluetooth/btintel.h
> > @@ -209,7 +209,7 @@ struct btintel_data {
> > #define btintel_wait_on_flag_timeout(hdev, nr, m, to)
> \
> > wait_on_bit_timeout(btintel_get_flag(hdev), (nr), m, to)
> >
> > -#if IS_ENABLED(CONFIG_BT_INTEL)
> > +#if IS_ENABLED(CONFIG_BT_INTEL) ||
> IS_ENABLED(CONFIG_BT_INTEL_PCIE)
> >
> > int btintel_check_bdaddr(struct hci_dev *hdev);
> > int btintel_enter_mfg(struct hci_dev *hdev);
> > diff --git a/drivers/bluetooth/btintel_pcie.c
> b/drivers/bluetooth/btintel_pcie.c
> > new file mode 100644
> > index 000000000000..e6ce2304dc57
> > --- /dev/null
> > +++ b/drivers/bluetooth/btintel_pcie.c
> > @@ -0,0 +1,1317 @@
> > +// SPDX-License-Identifier: GPL-2.0-or-later
> > +/*
> > + * Intel Bluetooth PCIE driver
> > + *
> > + * Copyright (C) 2017 Intel Corporation. All rights reserved.
> > + *
> > + * This program is free software; you can redistribute it and/or
> > + * modify it under the terms of the GNU General Public License version
> > + * 2 as published by the Free Software Foundation.
> > + *
> > + * This program is distributed in the hope that it will be useful,
> > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> > + * GNU General Public License for more details.
> > + *
> > + * Copyright (C) 2022 Intel Corporation
>
> Are two copyright lines needed?
>
No. I overlooked this. I will fix in v2 version.
> > + *
> > + * Intel Bluetooth Driver for PCIE interface.
> > + */
> > +#include <linux/kernel.h>
> > +#include <linux/module.h>
> > +#include <linux/firmware.h>
> > +#include <linux/pci.h>
> > +#include <linux/wait.h>
> > +#include <linux/delay.h>
> > +#include <linux/interrupt.h>
> > +
> > +#include <asm/unaligned.h>
> > +
> > +#include <net/bluetooth/bluetooth.h>
> > +#include <net/bluetooth/hci_core.h>
> > +
> > +#include "btintel.h"
> > +#include "btintel_pcie.h"
> > +
> > +#define VERSION "0.1"
> > +
> > +#define BTINTEL_PCI_DEVICE(dev, subdev) \
> > + .vendor = PCI_VENDOR_ID_INTEL, \
> > + .device = (dev), \
> > + .subvendor = PCI_ANY_ID, \
> > + .subdevice = (subdev), \
> > + .driver_data = 0
> > +
> > +/* Intel Bluetooth PCIe device id table */
> > +static const struct pci_device_id btintel_pcie_table[] = {
> > + { BTINTEL_PCI_DEVICE(0xA876, PCI_ANY_ID) },
> > + { 0 }
> > +};
> > +MODULE_DEVICE_TABLE(pci, btintel_pcie_table);
> > +
> > +/* Intel PCIe uses 4 bytes of HCI type instead of 1 byte BT SIG HCI type */
> > +#define BTINTEL_PCIE_HCI_TYPE_LEN 4
> > +#define BTINTEL_PCIE_HCI_CMD_PKT 0x00000001
> > +#define BTINTEL_PCIE_HCI_ACL_PKT 0x00000002
> > +#define BTINTEL_PCIE_HCI_SCO_PKT 0x00000003
> > +#define BTINTEL_PCIE_HCI_EVT_PKT 0x00000004
> > +
> > +#define BTITNEL_PCIE_ENABLE_HCI_DUMP 0
>
> Mention this macro in the commit message?
I will remove this macro as we have monitor to dump all the HCI traffic.
>
> > +
> > +#if BTITNEL_PCIE_ENABLE_HCI_DUMP
> > +static inline void btintel_pcie_hci_dump(const char *p, const void *b, int s)
> > +{
> > + const unsigned char *ptr = (const unsigned char *)b;
> > + char str[64];
> > + int c, i;
> > +
> > + for (i = c = 0; c < s; c++) {
> > + i += snprintf(str + i, sizeof(str) - i, "%02x ", ptr[c]);
> > + if ((c > 0 && (c + 1) % 8 == 0) || (c == s - 1)) {
> > + BT_DBG("%s: %s", p, str);
> > + i = 0;
> > + }
> > + }
> > +}
> > +#else
> > +static inline void btintel_pcie_hci_dump(const char *p, const void *b, int s)
> > +{
> > +}
> > +#endif
>
> Is there a way to test this code, that means some CI setting
> `BTITNEL_PCIE_ENABLE_HCI_DUMP`? Would the linker remove unneeded
> code,
> if you did
>
> static inline void btintel_pcie_hci_dump(const char *p, const void
> *b, int s)
> {
> if (BTITNEL_PCIE_ENABLE_HCI_DUMP) {
> Everything here.
> }
> }
>
> > +
> > +static void ipc_print_ia_ring(struct ia *ia, u16 queue_num)
> > +{
> > + BT_DBG("[%s] ---------------- ia ----------------",
> > + queue_num == TXQ_NUM ? "TXQ" : "RXQ");
> > + BT_DBG("[%s] tr-h:%02u tr-t:%02u cr-h:%02u cr-t:%02u",
> > + queue_num == TXQ_NUM ? "TXQ" : "RXQ",
> > + ia->tr_hia[queue_num], ia->tr_tia[queue_num],
> > + ia->cr_hia[queue_num], ia->cr_tia[queue_num]);
> > +}
> > +
> > +static void ipc_print_urbd0(struct urbd0 *urbd0, u16 index)
> > +{
> > + BT_DBG("[TXQ] -------------- urbd0[%u] --------------", index);
> > + BT_DBG("[TXQ] tfd_index:%u num_txq:%u cmpl_cnt:%u
> immediate_cmpl:0x%x",
> > + urbd0->tfd_index, urbd0->num_txq, urbd0->cmpl_count,
> > + urbd0->immediate_cmpl);
> > +}
> > +
> > +static void ipc_print_frbd(struct frbd *frbd, u16 index)
> > +{
> > + BT_DBG("[RXQ] -------------- frbd[%u] --------------", index);
> > + BT_DBG("[RXQ] tag:%u addr:0x%llx", frbd->tag, frbd->addr);
> > +}
> > +
> > +static void ipc_print_urbd1(struct urbd1 *urbd1, u16 index)
> > +{
> > + BT_DBG("[RXQ] -------------- urbd1[%u] --------------", index);
> > + BT_DBG("[RXQ] frbd_tag:%u status: 0x%x fixed:0x%x",
> > + urbd1->frbd_tag, urbd1->status, urbd1->fixed);
> > +}
> > +
> > +/* Poll internal in microseconds */
> > +#define POLL_INTERVAL 10
>
> Please put the unit into the name: `POLL_INTERVAL_MS`. Then the comment
> can also be removed as redundant.
Ack.
>
> > +
> > +static int btintel_pcie_poll_bit(struct btintel_pcie_data *data, u32 offset,
> > + u32 bits, u32 mask, int timeout)
>
> Add the unit to `timeout`
Ack.
>
> > +{
> > + int t = 0;
> > + u32 reg;
> > +
> > + BT_DBG("Enter poll_bit");
>
> Is this needed? Doesn’t Linux’ tracing framework cover this already?
Ack.
>
> > + do {
> > + reg = btintel_pcie_rd_reg32(data, offset);
> > + BT_DBG("CURRENT FUNC_CTRL_REG: 0x%x", reg);
> > +
> > + if ((reg & mask) == (bits & mask)) {
> > + BT_DBG("Poll bit matched");
> > + return t;
> > + }
> > + udelay(POLL_INTERVAL);
> > + t += POLL_INTERVAL;
> > + BT_DBG("Poll wait: %d", t);
>
> Maybe elaborate, so it’s clear it’s the cummulative time. Maybe also
> print `timeout` value?
Timeout values are static. Let me know if its really required. BTW, I will remove BT_DBG logs which are not of much help.
>
> > + } while (t < timeout);
> > +
> > + return -ETIMEDOUT;
> > +}
> > +
> > +static struct btintel_pcie_data *btintel_pcie_get_data(struct msix_entry
> *entry)
> > +{
> > + u8 queue = entry->entry;
> > + struct msix_entry *entries = entry - queue;
> > +
> > + return container_of(entries, struct btintel_pcie_data, msix_entries[0]);
> > +}
> > +
> > +/* Set the doorbell for RXQ to notify the device that @index(actually index-
> 1)
> > + * is available to receive the data
> > + */
> > +static void btintel_pcie_set_rx_db(struct btintel_pcie_data *data, u16
> index)
> > +{
> > + u32 val;
> > +
> > + val = index;
> > + val |= (513 << 16);
> > +
> > + BT_DBG("[RXQ] Set doorbell for index: %u", index);
> > + btintel_pcie_wr_reg32(data, CSR_HBUS_TARG_WRPTR, val);
> > +}
> > +
> > +/* Update the FRBD(free buffer descriptor) with the @frbd_index and the
> > + * DMA address of the free buffer.
> > + */
> > +static void btintel_pcie_prepare_rx(struct rxq *rxq, u16 frbd_index)
> > +{
> > + struct data_buf *buf;
> > + struct frbd *frbd;
> > +
> > + /* Get the buffer of the frbd for DMA */
> > + buf = &rxq->bufs[frbd_index];
> > +
> > + frbd = &rxq->frbds[frbd_index];
> > + memset(frbd, 0, sizeof(*frbd));
> > +
> > + /* Update FRBD */
> > + frbd->tag = frbd_index;
> > + frbd->addr = buf->data_p_addr;
> > + ipc_print_frbd(frbd, frbd_index);
> > +}
> > +
> > +static int btintel_pcie_submit_rx(struct btintel_pcie_data *data)
> > +{
> > + u16 frbd_index;
> > + struct rxq *rxq = &data->rxq;
> > +
> > + /* Read the frbd index from the TR_HIA(Head Index Array) for RXQ */
> > + frbd_index = data->ia.tr_hia[RXQ_NUM];
> > + BT_DBG("[RXQ] current frbd_index: %u", frbd_index);
> > +
> > + /* Make sure the index value is within the range. It shouldn't be
> > + * bigger than the total count of the queue.
> > + */
> > + if (frbd_index > rxq->count) {
> > + BT_ERR("[RXQ] RXQ out of range: (0x%x)", frbd_index);
> > + return -ERANGE;
> > + }
> > +
> > + /* Prepare for RX submit. It updates the FRBD with the address of
> DMA
> > + * buffer
> > + */
> > + btintel_pcie_prepare_rx(rxq, frbd_index);
> > +
> > + /* Update TR_HIA with new FRBD index */
> > + frbd_index = (frbd_index + 1) % rxq->count;
> > + data->ia.tr_hia[RXQ_NUM] = frbd_index;
> > + ipc_print_ia_ring(&data->ia, RXQ_NUM);
> > +
> > + /* Set the doorbell to notify the device */
> > + btintel_pcie_set_rx_db(data, frbd_index);
> > +
> > + BT_DBG("[RXQ] rx sumbit completed");
> > +
> > + return 0;
> > +}
> > +
> > +static int btintel_pcie_start_rx(struct btintel_pcie_data *data)
> > +{
> > + int i, ret;
> > +
> > + for (i = 0; i < RX_MAX_QUEUE; i++) {
> > + ret = btintel_pcie_submit_rx(data);
> > + if (ret) {
> > + BT_ERR("[RXQ] failed to submit frbd(%d)", ret);
> > + return ret;
> > + }
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static void btintel_pcie_reset_ia(struct btintel_pcie_data *data)
> > +{
> > + memset(data->ia.tr_hia, 0, sizeof(u16) * NUM_QUEUES);
> > + memset(data->ia.tr_tia, 0, sizeof(u16) * NUM_QUEUES);
> > + memset(data->ia.cr_hia, 0, sizeof(u16) * NUM_QUEUES);
> > + memset(data->ia.cr_tia, 0, sizeof(u16) * NUM_QUEUES);
> > + BT_DBG("Index Arrays are reset");
> > +}
> > +
> > +static void btintel_pcie_reset_bt(struct btintel_pcie_data *data)
> > +{
> > + BT_INFO("Reset BT Function ");
> > + btintel_pcie_wr_reg32(data, CSR_FUNC_CTRL_REG,
> CSR_FUNC_CTRL_SW_RESET);
> > +}
> > +
> > +/* This function enables BT function by setting CSR_FUNC_CTRL_MAC_INIT
> bit in
> > + * CSR_FUNC_CTRL_REG register and wait for MSI-X with
> MSIX_HW_INT_CAUSES_GP0.
> > + * Then the host reads firmware version from CSR_F2D_MBX and the boot
> stage
> > + * from CSR_BOOT_STAGE_REG.
> > + */
> > +static int btintel_pcie_enable_bt(struct btintel_pcie_data *data)
> > +{
> > + int err;
> > + u32 reg;
> > +
> > + data->gp0_received = false;
> > +
> > + /* Update the DMA address of CI struct to CSR */
> > + btintel_pcie_wr_reg32(data, CSR_CI_ADDR_LSB_REG,
> > + data->ci_p_addr & 0xffffffff);
> > + btintel_pcie_wr_reg32(data, CSR_CI_ADDR_MSB_REG,
> > + data->ci_p_addr >> 32);
> > +
> > + /* Reset the cached value of boot stage. it is updated by the msix
> > + * gp0 interrupt handler.
> > + */
> > + data->boot_stage_cache = 0x0;
> > +
> > + /* Set MAC_INIT bit to start primary bootloader */
> > + reg = btintel_pcie_rd_reg32(data, CSR_FUNC_CTRL_REG);
> > + BT_INFO("Before: FUNC_CTRL_REG: 0x%x", reg);
> > +
> > + btintel_pcie_set_reg_bits(data, CSR_FUNC_CTRL_REG,
> > + CSR_FUNC_CTRL_MAC_INIT);
> > + BT_INFO("MAC_INIT is set");
> > +
> > + /* Wait until MAC_ACCESS is granted */
> > + err = btintel_pcie_poll_bit(data, CSR_FUNC_CTRL_REG,
> > + CSR_FUNC_CTRL_MAC_ACCESS_STS,
> > + CSR_FUNC_CTRL_MAC_ACCESS_STS,
> > + DEFAULT_MAC_ACCESS_TIMEOUT);
> > + if (err < 0) {
> > + BT_ERR("Failed to start bootloader even after %u ns",
> > + DEFAULT_MAC_ACCESS_TIMEOUT);
> > + return -ENODEV;
> > + }
> > +
> > + /* MAC is ready. Enable BT FUNC */
> > + btintel_pcie_set_reg_bits(data, CSR_FUNC_CTRL_REG,
> > + CSR_FUNC_CTRL_FUNC_ENA |
> > + CSR_FUNC_CTRL_FUNC_INIT);
> > +
> > + reg = btintel_pcie_rd_reg32(data, CSR_FUNC_CTRL_REG);
> > + BT_INFO("After: FUNC_CTRL_REG: 0x%x", reg);
> > +
> > + /* wait for interrupt from the device after booting up to primary
> > + * bootloader.
> > + */
> > + err = wait_event_timeout(data->gp0_wait_q, data->gp0_received,
> > + msecs_to_jiffies(DEFAULT_INTR_TIMEOUT));
> > + if (!err) {
> > + BT_ERR("Failed to receive mac_init interrupt");
> > + return -ETIME;
> > + }
> > +
> > + /* Check cached boot stage is CSR_BOOT_STAGE_ROM(BIT(0)) */
> > + if (~data->boot_stage_cache & CSR_BOOT_STAGE_ROM) {
> > + BT_ERR("Device is not running in rom");
> > + return -ENODEV;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +/* This function handles the MSI-X interrupt for gp0 cause(bit 0 in
> > + * CSR_MSIX_HW_INT_CAUSES) which is sent for boot stage and image
> response.
> > + */
> > +static void btintel_pcie_msix_gp0_handler(struct btintel_pcie_data *data)
> > +{
> > + u32 reg;
> > +
> > + /* This interrupt is for three different causes and it is not easy to
> > + * know what causes the interrupt. So, it compares each register value
> > + * with cached value and update it before it wake up the queue.
> > + */
> > + reg = btintel_pcie_rd_reg32(data, CSR_BOOT_STAGE_REG);
> > + if (reg != data->boot_stage_cache) {
> > + data->boot_stage_cache = reg;
> > +
> > + BT_DBG("Boot Stage updated: 0x%x", reg);
> > + }
> > +
> > + reg = btintel_pcie_rd_reg32(data, CSR_IMG_RESPONSE_REG);
> > + if (reg != data->img_resp_cache) {
> > + data->img_resp_cache = reg;
> > +
> > + BT_DBG("Image Response updated: 0x%x", reg);
> > + }
> > +
> > + BT_DBG("---------- cached GP0 registers ----------");
> > + BT_DBG("Cached Boot Stage Reg: 0x%x", data->boot_stage_cache);
> > + BT_DBG("Cached Image Resp Reg: 0x%x", data->img_resp_cache);
> > +
> > + data->gp0_received = true;
> > +
> > + /* If the boot stage is OP or IML, reset IA and start RX again */
> > + if (data->boot_stage_cache & CSR_BOOT_STAGE_OPFW ||
> > + data->boot_stage_cache & CSR_BOOT_STAGE_IML) {
> > + btintel_pcie_reset_ia(data);
> > + btintel_pcie_start_rx(data);
> > + }
> > +
> > + wake_up(&data->gp0_wait_q);
> > +}
> > +
> > +/* This function handles the MSX-X interrupt for rx queue 0 which is for TX
> > + */
> > +static void btintel_pcie_msix_tx_handle(struct btintel_pcie_data *data)
> > +{
> > + u16 cr_tia, cr_hia;
> > + struct txq *txq;
> > + struct urbd0 *urbd0;
> > +
> > + cr_tia = data->ia.cr_tia[TXQ_NUM];
> > + cr_hia = data->ia.cr_hia[TXQ_NUM];
> > +
> > + BT_DBG("[TXQ] cr_hia=%u cr_tia=%u", cr_hia, cr_tia);
> > +
> > + /* Check CR_TIA and CR_HIA for change */
> > + if (cr_tia == cr_hia) {
> > + BT_ERR("[TXQ] no new CD found");
> > + return;
> > + }
> > +
> > + txq = &data->txq;
> > +
> > + while (cr_tia != cr_hia) {
> > + BT_DBG("[TXQ] wake up tx_wait_q");
> > +
> > + data->tx_wait_done = true;
> > + wake_up(&data->tx_wait_q);
> > +
> > + /* Get URBD0 pointed by cr_tia */
> > + urbd0 = &txq->urbd0s[cr_tia];
> > + ipc_print_urbd0(urbd0, cr_tia);
> > +
> > + /* Make sure the completed TFD index is within the range */
> > + if (urbd0->tfd_index > txq->count) {
> > + BT_ERR("[TXQ] out of range: (0x%x)", urbd0-
> >tfd_index);
> > + return;
> > + }
> > +
> > + /* Increase cr_tia */
> > + cr_tia = (cr_tia + 1) % txq->count;
> > + data->ia.cr_tia[TXQ_NUM] = cr_tia;
> > + ipc_print_ia_ring(&data->ia, TXQ_NUM);
> > + }
> > +}
> > +
> > +static int btintel_pcie_recv_event_intel(struct hci_dev *hdev,
> > + struct sk_buff *skb)
> > +{
> > + if (btintel_test_flag(hdev, INTEL_BOOTLOADER)) {
> > + struct hci_event_hdr *hdr = (void *)skb->data;
> > +
> > + if (skb->len > HCI_EVENT_HDR_SIZE && hdr->evt == 0xff &&
> > + hdr->plen > 0) {
> > + const void *ptr = skb->data + HCI_EVENT_HDR_SIZE +
> 1;
> > + unsigned int len = skb->len - HCI_EVENT_HDR_SIZE -
> 1;
> > +
> > + switch (skb->data[2]) {
> > + case 0x02:
> > + /* When switching to the operational
> firmware
> > + * the device sends a vendor specific event
> > + * indicating that the bootup completed.
> > + */
> > + btintel_bootup(hdev, ptr, len);
> > + break;
> > + case 0x06:
> > + /* When the firmware loading completes the
> > + * device sends out a vendor specific event
> > + * indicating the result of the firmware
> > + * loading.
> > + */
> > + btintel_secure_send_result(hdev, ptr, len);
> > + break;
> > + }
> > + }
> > + }
> > +
> > + return hci_recv_frame(hdev, skb);
> > +}
> > +
> > +/* Process the received rx data
> > + * It check the frame header to identify the data type and create skb
> > + * and calling HCI API
> > + */
> > +static int btintel_pcie_hci_recv_frame(struct btintel_pcie_data *data,
> > + void *buf, int count)
> > +{
> > + struct hci_dev *hdev = data->hdev;
> > + int ret;
> > + u32 pkt_type;
> > + u16 plen;
> > + struct sk_buff *skb;
> > +
> > + spin_lock(&data->hci_rx_lock);
> > +
> > + /* The first 4 bytes indicates the Intel PCIe specific packet type.
> > + * Read the packet type here before remove it.
> > + */
> > + pkt_type = get_unaligned_le32(buf);
> > + bt_dev_dbg(hdev, "pkt_type=%u count=%d", pkt_type, count);
> > +
> > + buf += BTINTEL_PCIE_HCI_TYPE_LEN;
> > + count -= BTINTEL_PCIE_HCI_TYPE_LEN;
> > +
> > + hdev->stat.byte_rx += count;
> > +
> > + skb = bt_skb_alloc(count, GFP_ATOMIC);
> > + if (!skb) {
> > + bt_dev_err(hdev, "Failed to allocate skb for event");
> > + ret = -ENOMEM;
> > + goto exit_error;
> > + }
> > +
> > + switch (pkt_type) {
> > + case BTINTEL_PCIE_HCI_ACL_PKT:
> > + hci_skb_pkt_type(skb) = HCI_ACLDATA_PKT;
> > + memcpy(skb_put(skb, HCI_ACL_HDR_SIZE), buf,
> HCI_ACL_HDR_SIZE);
> > + plen = hci_acl_hdr(skb)->dlen;
> > + buf += HCI_ACL_HDR_SIZE;
> > + break;
> > + case BTINTEL_PCIE_HCI_SCO_PKT:
> > + hci_skb_pkt_type(skb) = HCI_SCODATA_PKT;
> > + memcpy(skb_put(skb, HCI_SCO_HDR_SIZE), buf,
> HCI_SCO_HDR_SIZE);
> > + plen = hci_sco_hdr(skb)->dlen;
> > + buf += HCI_SCO_HDR_SIZE;
> > + break;
> > + case BTINTEL_PCIE_HCI_EVT_PKT:
> > + hci_skb_pkt_type(skb) = HCI_EVENT_PKT;
> > + memcpy(skb_put(skb, HCI_EVENT_HDR_SIZE), buf,
> > + HCI_EVENT_HDR_SIZE);
> > + plen = hci_event_hdr(skb)->plen;
> > + buf += HCI_EVENT_HDR_SIZE;
> > + break;
> > + default:
> > + ret = -EILSEQ;
> > + kfree_skb(skb);
> > + goto exit_error;
> > + }
> > + memcpy(skb_put(skb, plen), buf, plen);
> > +
> > + if (pkt_type == BTINTEL_PCIE_HCI_EVT_PKT)
> > + ret = btintel_pcie_recv_event_intel(hdev, skb);
> > + else
> > + ret = hci_recv_frame(hdev, skb);
> > +
> > +exit_error:
> > + if (ret)
> > + hdev->stat.err_rx++;
> > +
> > + spin_unlock(&data->hci_rx_lock);
> > +
> > + return ret;
> > +}
> > +
> > +/* RX work queue */
> > +static void btintel_pcie_rx_work(struct work_struct *work)
> > +{
> > + struct btintel_pcie_data *data = container_of(work,
> > + struct btintel_pcie_data, rx_work);
> > + struct sk_buff *skb;
> > + int err;
> > +
> > + /* Process the sk_buf in queue and send to the hci layer */
> > + while ((skb = skb_dequeue(&data->rx_skb_q))) {
> > + err = btintel_pcie_hci_recv_frame(data, skb->data, skb->len);
> > + if (err) {
> > + BT_ERR("Failed to send received frame: %d", err);
> > + kfree_skb(skb);
> > + }
> > + }
> > +}
> > +
> > +/* create the sk_buff with data and save it to queue and start rx work
> > + */
> > +static int btintel_pcie_submit_rx_work(struct btintel_pcie_data *data, u8
> status,
> > + void *buf)
> > +{
> > + int ret, len;
> > + struct rfh_hdr *rfh_hdr;
> > + struct sk_buff *skb;
> > +
> > + rfh_hdr = (struct rfh_hdr *)buf;
> > + btintel_pcie_hci_dump("RFH HDR", buf, sizeof(*rfh_hdr));
> > +
> > + len = rfh_hdr->packet_len;
> > +
> > + /* Remove RFH header */
> > + buf += sizeof(*rfh_hdr);
> > + btintel_pcie_hci_dump("RX", buf, len);
> > +
> > + /* Create the sk_buf with packet in the buf and save it to sk_buf
> queue
> > + */
> > + skb = alloc_skb(len, GFP_ATOMIC);
> > + if (!skb) {
> > + ret = -ENOMEM;
> > + goto resubmit;
> > + }
> > +
> > + /* Copy the data to skb */
> > + memcpy(skb_put(skb, len), buf, len);
> > +
> > + /* Save the skb to rx queue */
> > + skb_queue_tail(&data->rx_skb_q, skb);
> > +
> > + /* Calling rx_work queue to process the skb */
> > + queue_work(data->workqueue, &data->rx_work);
> > +
> > +resubmit:
> > + BT_DBG("submit next read request");
> > +
> > + /* submit read */
> > + ret = btintel_pcie_submit_rx(data);
> > +
> > + return ret;
> > +}
> > +
> > +/* This function handles the MSI-X interrupt for rx queue 1 which is for RX
> > + */
> > +static void btintel_pcie_msix_rx_handle(struct btintel_pcie_data *data)
> > +{
> > + u16 cr_hia, cr_tia;
> > + struct rxq *rxq;
> > + struct urbd1 *urbd1;
> > + struct frbd *frbd;
> > + struct data_buf *buf;
> > + int ret;
> > +
> > + cr_hia = data->ia.cr_hia[RXQ_NUM];
> > + cr_tia = data->ia.cr_tia[RXQ_NUM];
> > +
> > + BT_DBG("[RXQ] cr_hia=%u cr_tia=%u", cr_hia, cr_tia);
> > +
> > + /* Check CR_TIA and CR_HIA for change */
> > + if (cr_tia == cr_hia) {
> > + BT_ERR("[RXQ] no new CD found");
> > + return;
> > + }
> > +
> > + rxq = &data->rxq;
> > +
> > + /* The firmware sends multiple CD in a single MSIX and it needs to
> > + * process all received CDs in this interrupt.
> > + */
> > + while (cr_tia != cr_hia) {
> > + /* Get URBD1 pointed by cr_tia */
> > + urbd1 = &rxq->urbd1s[cr_tia];
> > + ipc_print_urbd1(urbd1, cr_tia);
> > +
> > + /* Get FRBD poined by urbd1->frbd_tag */
> > + frbd = &rxq->frbds[urbd1->frbd_tag];
> > +
> > + /* Get buf from FRBD tag */
> > + buf = &rxq->bufs[urbd1->frbd_tag];
> > + if (!buf) {
> > + BT_ERR("[RXQ] failed to get the DMA buffer for %d",
> > + urbd1->frbd_tag);
> > + return;
> > + }
> > +
> > + /* prepare RX work */
> > + ret = btintel_pcie_submit_rx_work(data, urbd1->status,
> > + buf->data);
> > + if (ret) {
> > + BT_ERR("[RXQ] failed to submit rx request");
> > + return;
> > + }
> > +
> > + /* Update cr_tia */
> > + cr_tia = (cr_tia + 1) % rxq->count;
> > + data->ia.cr_tia[RXQ_NUM] = cr_tia;
> > + ipc_print_ia_ring(&data->ia, RXQ_NUM);
> > + }
> > + BT_DBG("[RXQ] completed rx interrupt");
> > +}
> > +
> > +static irqreturn_t btintel_pcie_msix_isr(int irq, void *data)
> > +{
> > + return IRQ_WAKE_THREAD;
> > +}
> > +
> > +static irqreturn_t btintel_pcie_irq_msix_handler(int irq, void *dev_id)
> > +{
> > + struct msix_entry *entry = dev_id;
> > + struct btintel_pcie_data *data = btintel_pcie_get_data(entry);
> > + u32 intr_fh, intr_hw;
> > +
> > + BT_DBG("handling msix(irq=%d dev_id=0x%p)", irq, dev_id);
> > +
> > + spin_lock(&data->irq_lock);
> > + intr_fh = btintel_pcie_rd_reg32(data, CSR_MSIX_FH_INT_CAUSES);
> > + intr_hw = btintel_pcie_rd_reg32(data, CSR_MSIX_HW_INT_CAUSES);
> > +
> > + /* Clear causes registers to avoid being handling the same cause */
> > + btintel_pcie_wr_reg32(data, CSR_MSIX_FH_INT_CAUSES, intr_fh);
> > + btintel_pcie_wr_reg32(data, CSR_MSIX_HW_INT_CAUSES, intr_hw);
> > + spin_unlock(&data->irq_lock);
> > +
> > + BT_DBG("intr_fh=0x%x intr_hw=0x%x", intr_fh, intr_hw);
> > +
> > + if (unlikely(!(intr_fh | intr_hw))) {
> > + BT_DBG("Ignore interrupt, inta == 0");
> > + return IRQ_NONE;
> > + }
> > +
> > + /* This interrupt is triggered by the firmware after updating
> > + * boot_stage register and image_response register
> > + */
> > + if (intr_hw & MSIX_HW_INT_CAUSES_GP0) {
> > + BT_DBG("intr for MSIX_HW_INT_CAUSES_GP0");
> > + btintel_pcie_msix_gp0_handler(data);
> > + }
> > +
> > + /* For TX */
> > + if (intr_fh & MSIX_FH_INT_CAUSES_0) {
> > + BT_DBG("intr for MSIX_FH_INT_CAUSES_0");
> > + btintel_pcie_msix_tx_handle(data);
> > + }
> > +
> > + /* For RX */
> > + if (intr_fh & MSIX_FH_INT_CAUSES_1) {
> > + BT_DBG("intr for MSIX_FH_INT_CAUSES_1");
> > + btintel_pcie_msix_rx_handle(data);
> > + }
> > +
> > + /* TODO: Add handler for other causes */
> > + /*
> > + * Before sending the interrupt the HW disables it to prevent
> > + * a nested interrupt. This is done by writing 1 to the corresponding
> > + * bit in the mask register. After handling the interrupt, it should be
> > + * re-enabled by clearing this bit. This register is defined as
> > + * write 1 clear (W1C) register, meaning that it's being clear
> > + * by writing 1 to the bit.
> > + */
> > + btintel_pcie_wr_reg32(data, CSR_MSIX_AUTOMASK_ST, BIT(entry-
> >entry));
> > +
> > + return IRQ_HANDLED;
> > +}
> > +
> > +/* This function requests the irq for msix and registers the handlers per irq.
> > + * Currently, it requests only 1 irq for all interrupt causes.
> > + */
> > +static int btintel_pcie_setup_irq(struct btintel_pcie_data *data)
> > +{
> > + int err;
> > + int num_irqs, i;
> > +
> > + BT_DBG("Initialize msix_entries...");
> > + for (i = 0; i < MSIX_VEC_MAX; i++) {
> > + data->msix_entries[i].entry = i;
> > + BT_DBG("msix_entries[%d] vector=0x%x entry=0x%x",
> > + i, data->msix_entries[i].vector,
> > + data->msix_entries[i].entry);
> > + }
> > +
> > + num_irqs = pci_enable_msix_range(data->pdev, data->msix_entries,
> > + MSIX_VEC_MIN,
> > + MSIX_VEC_MAX);
> > + if (num_irqs < 0) {
> > + BT_ERR("Failed to enable msix range (%d)", num_irqs);
> > + return num_irqs;
> > + }
> > +
> > + data->alloc_vecs = num_irqs;
> > + data->msix_enabled = 1;
> > + data->def_irq = 0;
> > +
> > + BT_DBG("Returned num_irqs=%d", num_irqs);
> > + for (i = 0; i < num_irqs; i++) {
> > + BT_DBG("msix_entries[%d] vector=0x%x entry=0x%x", i,
> > + data->msix_entries[i].vector,
> > + data->msix_entries[i].entry);
> > + }
> > +
> > + BT_DBG("setup irq handler");
> > + for (i = 0; i < data->alloc_vecs; i++) {
> > + struct msix_entry *msix_entry;
> > +
> > + msix_entry = &data->msix_entries[i];
> > +
> > + err = devm_request_threaded_irq(&data->pdev->dev,
> > + msix_entry->vector,
> > + btintel_pcie_msix_isr,
> > +
> btintel_pcie_irq_msix_handler,
> > + IRQF_SHARED,
> > + KBUILD_MODNAME,
> > + msix_entry);
> > + if (err) {
> > + BT_ERR("Failed to allocate irq handler (%d)", err);
> > + return err;
> > + }
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +struct btintel_pcie_causes_list {
> > + u32 cause;
> > + u32 mask_reg;
> > + u8 cause_num;
> > +};
> > +
> > +struct btintel_pcie_causes_list causes_list[] = {
> > + { MSIX_FH_INT_CAUSES_0, CSR_MSIX_FH_INT_MASK,
> 0x00 },
> > + { MSIX_FH_INT_CAUSES_1, CSR_MSIX_FH_INT_MASK,
> 0x01 },
> > + { MSIX_HW_INT_CAUSES_GP0, CSR_MSIX_HW_INT_MASK, 0x20
> },
> > +};
> > +
> > +/* This function configures the interrupt masks for both HW_INT_CAUSES
> and
> > + * FH_INT_CAUSES which are meaningful to us.
> > + *
> > + * After resetting BT function via PCIE FLR or FUNC_CTRL reset, the driver
> > + * need to call this function again to configure it again since the masks
> > + * are reset to 0xFFFFFFFF after reset.
> > + */
> > +static void btintel_pcie_config_msix(struct btintel_pcie_data *data)
> > +{
> > + int i;
> > + int val = data->def_irq | MSIX_NON_AUTO_CLEAR_CAUSE;
> > +
> > + /* Set Non Auto Clear Cause */
> > + for (i = 0; i < ARRAY_SIZE(causes_list); i++) {
> > + btintel_pcie_wr_reg8(data,
> > + CSR_MSIX_IVAR(causes_list[i].cause_num),
> > + val);
> > + btintel_pcie_clr_reg_bits(data,
> > + causes_list[i].mask_reg,
> > + causes_list[i].cause);
> > + }
> > +
> > + /* Save the initial interrupt mask */
> > + data->fh_init_mask = ~btintel_pcie_rd_reg32(data,
> CSR_MSIX_FH_INT_MASK);
> > + data->hw_init_mask = ~btintel_pcie_rd_reg32(data,
> CSR_MSIX_HW_INT_MASK);
> > + BT_DBG("init_mask: fh=0x%x hw=0x%x", data->fh_init_mask,
> > + data->hw_init_mask);
> > +}
> > +
> > +static int btintel_pcie_config_pcie(struct pci_dev *pdev,
> > + struct btintel_pcie_data *data)
> > +{
> > + int err;
> > +
> > + err = pcim_enable_device(pdev);
> > + if (err) {
> > + BT_ERR("Failed to enable pci device (%d)", err);
> > + return err;
> > + }
> > + pci_set_master(pdev);
> > +
> > + /* Setup DMA mask */
> > + BT_DBG("Set DMA_MASK(64)");
> > + err = dma_set_mask_and_coherent(&pdev->dev,
> DMA_BIT_MASK(64));
> > + if (err) {
> > + BT_DBG("Set DMA_MASK(32)");
> > + err = dma_set_mask_and_coherent(&pdev->dev,
> DMA_BIT_MASK(32));
> > + /* Both attempt failed */
> > + if (err) {
> > + BT_ERR("No suitable DMA available");
> > + return err;
> > + }
> > + }
> > +
> > + /* Get BAR to access CSR */
> > + err = pcim_iomap_regions(pdev, BIT(0), KBUILD_MODNAME);
> > + if (err) {
> > + BT_ERR("Failed to get iomap regions (%d)", err);
> > + return err;
> > + }
> > +
> > + data->base_addr = pcim_iomap_table(pdev)[0];
> > + if (!data->base_addr) {
> > + BT_ERR("Failed to get base address");
> > + return -ENODEV;
> > + }
> > +
> > + err = btintel_pcie_setup_irq(data);
> > + if (err) {
> > + BT_ERR("Failed to setup irq for msix");
> > + return err;
> > + }
> > +
> > + /* Configure MSI-X with causes list */
> > + btintel_pcie_config_msix(data);
> > +
> > + return 0;
> > +}
> > +
> > +static void btintel_pcie_init_ci(struct btintel_pcie_data *data,
> > + struct ctx_info *ci)
> > +{
> > + ci->version = 0x1;
> > + ci->size = sizeof(*ci);
> > + ci->config = 0x0000;
> > + ci->addr_cr_hia = data->ia.cr_hia_p_addr;
> > + ci->addr_tr_tia = data->ia.tr_tia_p_addr;
> > + ci->addr_cr_tia = data->ia.cr_tia_p_addr;
> > + ci->addr_tr_hia = data->ia.tr_hia_p_addr;
> > + ci->num_cr_ia = NUM_QUEUES;
> > + ci->num_tr_ia = NUM_QUEUES;
> > + ci->addr_urbdq0 = data->txq.urbd0s_p_addr;
> > + ci->addr_tfdq = data->txq.tfds_p_addr;
> > + ci->num_tfdq = data->txq.count;
> > + ci->num_urbdq0 = data->txq.count;
> > + ci->tfdq_db_vec = TXQ_NUM;
> > + ci->urbdq0_db_vec = TXQ_NUM;
> > + ci->rbd_size = RBD_SIZE_4K;
> > + ci->addr_frbdq = data->rxq.frbds_p_addr;
> > + ci->num_frbdq = data->rxq.count;
> > + ci->frbdq_db_vec = RXQ_NUM;
> > + ci->addr_urbdq1 = data->rxq.urbd1s_p_addr;
> > + ci->num_urbdq1 = data->rxq.count;
> > + ci->urbdq_db_vec = RXQ_NUM;
> > +}
> > +
> > +static void btintel_pcie_free_txq_bufs(struct btintel_pcie_data *data,
> > + struct txq *txq)
> > +{
> > + /* Free data buffers first */
> > + dma_free_coherent(&data->pdev->dev, txq->count * BUFFER_SIZE,
> > + txq->buf_v_addr, txq->buf_p_addr);
> > + kfree(txq->bufs);
> > + BT_DBG("txq buffers are freed");
> > +}
> > +
> > +static int btintel_pcie_setup_txq_bufs(struct btintel_pcie_data *data,
> > + struct txq *txq)
> > +{
> > + int err = 0, i;
> > + struct data_buf *buf;
> > +
> > + if (txq->count == 0) {
> > + BT_ERR("invalid parameter: txq->count");
> > + err = -EINVAL;
> > + goto exit_error;
> > + }
> > +
> > + /* Allocate the same number of buffers as the descriptor */
> > + txq->bufs = kmalloc_array(txq->count, sizeof(*buf), GFP_KERNEL);
> > + if (!txq->bufs) {
> > + err = -ENOMEM;
> > + goto exit_error;
> > + }
> > +
> > + /* Allocate full chunk of data buffer for DMA first and do indexing and
> > + * initialization next, so it can be freed easily
> > + */
> > + txq->buf_v_addr = dma_alloc_coherent(&data->pdev->dev,
> > + txq->count * BUFFER_SIZE,
> > + &txq->buf_p_addr,
> > + GFP_KERNEL | __GFP_NOWARN);
> > + if (!txq->buf_v_addr) {
> > + BT_ERR("Failed to allocate DMA buf");
> > + err = -ENOMEM;
> > + kfree(txq->bufs);
> > + goto exit_error;
> > + }
> > + memset(txq->buf_v_addr, 0, txq->count * BUFFER_SIZE);
> > +
> > + BT_DBG("alloc bufs: p=0x%llx v=0x%p", txq->buf_p_addr, txq-
> >buf_v_addr);
> > +
> > + /* Setup the allocated DMA buffer to bufs. Each data_buf should
> > + * have virtual address and physical address
> > + */
> > + for (i = 0; i < txq->count; i++) {
> > + buf = &txq->bufs[i];
> > + buf->data_p_addr = txq->buf_p_addr + (i * BUFFER_SIZE);
> > + buf->data = txq->buf_v_addr + (i * BUFFER_SIZE);
> > + }
> > +
> > +exit_error:
> > + return err;
> > +}
> > +
> > +static void btintel_pcie_free_rxq_bufs(struct btintel_pcie_data *data,
> > + struct rxq *rxq)
> > +{
> > + /* Free data buffers first */
> > + dma_free_coherent(&data->pdev->dev, rxq->count * BUFFER_SIZE,
> > + rxq->buf_v_addr, rxq->buf_p_addr);
> > + kfree(rxq->bufs);
> > + BT_DBG("rxq buffers are freed");
> > +}
> > +
> > +static int btintel_pcie_setup_rxq_bufs(struct btintel_pcie_data *data,
> > + struct rxq *rxq)
> > +{
> > + int err = 0, i;
> > + struct data_buf *buf;
> > +
> > + if (rxq->count == 0) {
> > + BT_ERR("invalid parameter: rxq->count");
> > + err = -EINVAL;
> > + goto exit_error;
> > + }
> > +
> > + /* Allocate the same number of buffers as the descriptor */
> > + rxq->bufs = kmalloc_array(rxq->count, sizeof(*buf), GFP_KERNEL);
> > + if (!rxq->bufs) {
> > + err = -ENOMEM;
> > + goto exit_error;
> > + }
> > +
> > + /* Allocate full chunk of data buffer for DMA first and do indexing and
> > + * initialization next, so it can be freed easily
> > + */
> > + rxq->buf_v_addr = dma_alloc_coherent(&data->pdev->dev,
> > + rxq->count * BUFFER_SIZE,
> > + &rxq->buf_p_addr,
> > + GFP_KERNEL | __GFP_NOWARN);
> > + if (!rxq->buf_v_addr) {
> > + BT_ERR("Failed to allocate DMA buf");
> > + err = -ENOMEM;
> > + kfree(rxq->bufs);
> > + goto exit_error;
> > + }
> > + memset(rxq->buf_v_addr, 0, rxq->count * BUFFER_SIZE);
> > +
> > + BT_DBG("alloc bufs: p=0x%llx v=0x%p", rxq->buf_p_addr, rxq-
> >buf_v_addr);
> > +
> > + /* Setup the allocated DMA buffer to bufs. Each data_buf should
> > + * have virtual address and physical address
> > + */
> > + for (i = 0; i < rxq->count; i++) {
> > + buf = &rxq->bufs[i];
> > + buf->data_p_addr = rxq->buf_p_addr + (i * BUFFER_SIZE);
> > + buf->data = rxq->buf_v_addr + (i * BUFFER_SIZE);
> > + }
> > +
> > +exit_error:
> > +
> > + return err;
> > +}
> > +
> > +static void btintel_pcie_setup_ia(struct btintel_pcie_data *data,
> > + dma_addr_t p_addr, void *v_addr,
> > + struct ia *ia)
> > +{
> > + /* TR Head Index Array */
> > + ia->tr_hia_p_addr = p_addr;
> > + ia->tr_hia = v_addr;
> > +
> > + /* TR Tail Index Array */
> > + ia->tr_tia_p_addr = p_addr + sizeof(u16) * NUM_QUEUES;
> > + ia->tr_tia = v_addr + sizeof(u16) * NUM_QUEUES;
> > +
> > + /* CR Head index Array */
> > + ia->cr_hia_p_addr = p_addr + (sizeof(u16) * NUM_QUEUES * 2);
> > + ia->cr_hia = v_addr + (sizeof(u16) * NUM_QUEUES * 2);
> > +
> > + /* CR Tail Index Array */
> > + ia->cr_tia_p_addr = p_addr + (sizeof(u16) * NUM_QUEUES * 3);
> > + ia->cr_tia = v_addr + (sizeof(u16) * NUM_QUEUES * 3);
> > +}
> > +
> > +static void btintel_pcie_free(struct btintel_pcie_data *data)
> > +{
> > + btintel_pcie_free_rxq_bufs(data, &data->rxq);
> > + btintel_pcie_free_txq_bufs(data, &data->txq);
> > +
> > + dma_pool_free(data->dma_pool, data->dma_v_addr, data-
> >dma_p_addr);
> > + dma_pool_destroy(data->dma_pool);
> > + BT_DBG("DMA memory is freed");
> > +}
> > +
> > +/* Allocate tx and rx queues, any related data structures and buffers.
> > + */
> > +static int btintel_pcie_alloc(struct btintel_pcie_data *data)
> > +{
> > + int err = 0;
> > + size_t total;
> > + dma_addr_t p_addr;
> > + void *v_addr;
> > +
> > + /* Allocate the chunk of DMA memory for descriptors, index array,
> and
> > + * context information, instead of allocating individually.
> > + * The DMA memory for data buffer is allocated while setting up the
> > + * each queue.
> > + *
> > + * Total size is sum of the following
> > + * + size of TFD * Number of descriptors in queue
> > + * + size of URBD0 * Number of descriptors in queue
> > + * + size of FRBD * Number of descriptors in queue
> > + * + size of URBD1 * Number of descriptors in queue
> > + * + size of index * Number of queues(2) * type of index array(4)
> > + * + size of context information
> > + */
> > + total = (sizeof(struct tfd) + sizeof(struct urbd0) + sizeof(struct frbd)
> > + + sizeof(struct urbd1)) * DESCS_COUNT;
> > +
> > + /* Add the sum of size of index array and size of ci struct */
> > + total += (sizeof(u16) * NUM_QUEUES * 4) + sizeof(struct ctx_info);
> > +
> > + /* Allocate DMA Pool */
> > + data->dma_pool = dma_pool_create(KBUILD_MODNAME, &data-
> >pdev->dev,
> > + total, DMA_POOL_ALIGNMENT, 0);
> > + if (!data->dma_pool) {
> > + BT_ERR("Failed to allocate dma pool for queues");
> > + err = -ENOMEM;
> > + goto exit_error;
> > + }
> > +
> > + v_addr = dma_pool_zalloc(data->dma_pool, GFP_KERNEL |
> __GFP_NOWARN,
> > + &p_addr);
> > + if (!v_addr) {
> > + BT_ERR("Failed to alloc dma memory for queues");
> > + dma_pool_destroy(data->dma_pool);
> > + err = -ENOMEM;
> > + goto exit_error;
> > + }
> > +
> > + data->dma_p_addr = p_addr;
> > + data->dma_v_addr = v_addr;
> > +
> > + BT_DBG("dma pool: p_addr=0x%llx v_addr=0x%p", p_addr, v_addr);
> > +
> > + /* Setup descriptor count */
> > + data->txq.count = DESCS_COUNT;
> > + data->rxq.count = DESCS_COUNT;
> > +
> > + /* Setup tfds */
> > + data->txq.tfds_p_addr = p_addr;
> > + data->txq.tfds = v_addr;
> > +
> > + p_addr += (sizeof(struct tfd) * DESCS_COUNT);
> > + v_addr += (sizeof(struct tfd) * DESCS_COUNT);
> > +
> > + /* Setup urbd0 */
> > + data->txq.urbd0s_p_addr = p_addr;
> > + data->txq.urbd0s = v_addr;
> > +
> > + p_addr += (sizeof(struct urbd0) * DESCS_COUNT);
> > + v_addr += (sizeof(struct urbd0) * DESCS_COUNT);
> > +
> > + /* Setup frbd */
> > + data->rxq.frbds_p_addr = p_addr;
> > + data->rxq.frbds = v_addr;
> > +
> > + p_addr += (sizeof(struct frbd) * DESCS_COUNT);
> > + v_addr += (sizeof(struct frbd) * DESCS_COUNT);
> > +
> > + /* Setup urbd1 */
> > + data->rxq.urbd1s_p_addr = p_addr;
> > + data->rxq.urbd1s = v_addr;
> > +
> > + p_addr += (sizeof(struct urbd1) * DESCS_COUNT);
> > + v_addr += (sizeof(struct urbd1) * DESCS_COUNT);
> > +
> > + /* Setup data buffers for txq */
> > + err = btintel_pcie_setup_txq_bufs(data, &data->txq);
> > + if (err) {
> > + BT_ERR("Failed to setup txq buffers: %d", err);
> > + goto exit_error_pool;
> > + }
> > +
> > + /* Setup data buffers for rxq */
> > + err = btintel_pcie_setup_rxq_bufs(data, &data->rxq);
> > + if (err) {
> > + BT_ERR("Failed to allocate rxq buffers: %d", err);
> > + goto exit_error_txq;
> > + }
> > +
> > + /* Setup Index Array */
> > + btintel_pcie_setup_ia(data, p_addr, v_addr, &data->ia);
> > +
> > + /* Setup Context Information */
> > + p_addr += sizeof(u16) * NUM_QUEUES * 4;
> > + v_addr += sizeof(u16) * NUM_QUEUES * 4;
> > +
> > + data->ci = v_addr;
> > + data->ci_p_addr = p_addr;
> > +
> > + /* Initialize the CI */
> > + btintel_pcie_init_ci(data, data->ci);
> > +
> > + return 0;
> > +
> > +exit_error_txq:
> > + btintel_pcie_free_txq_bufs(data, &data->txq);
> > +exit_error_pool:
> > + dma_pool_free(data->dma_pool, data->dma_v_addr, data-
> >dma_p_addr);
> > + dma_pool_destroy(data->dma_pool);
> > +exit_error:
> > + return err;
> > +}
> > +
> > +static void btintel_pcie_release_hdev(struct btintel_pcie_data *data)
> > +{
> > + struct hci_dev *hdev;
> > +
> > + hdev = data->hdev;
> > + if (hdev) {
> > + hci_unregister_dev(hdev);
> > + hci_free_dev(hdev);
> > + }
> > + data->hdev = NULL;
> > +}
> > +
> > +static int btintel_pcie_setup_hdev(struct btintel_pcie_data *data)
> > +{
> > + /* TODO: initialize hdev and assign the callbacks to hdev */
> > + return -ENODEV;
> > +}
> > +
> > +static int btintel_pcie_probe(struct pci_dev *pdev,
> > + const struct pci_device_id *ent)
> > +{
> > + int err;
> > + struct btintel_pcie_data *data;
> > +
> > + if (!pdev)
> > + return -ENODEV;
> > +
> > + data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
> > + if (!data)
> > + return -ENOMEM;
> > +
> > + /* initialize the btintel_pcie data struct */
> > + data->pdev = pdev;
> > +
> > + spin_lock_init(&data->irq_lock);
> > + spin_lock_init(&data->hci_rx_lock);
> > +
> > + init_waitqueue_head(&data->gp0_wait_q);
> > + data->gp0_received = false;
> > +
> > + init_waitqueue_head(&data->tx_wait_q);
> > + data->tx_wait_done = false;
> > +
> > + data->workqueue = alloc_ordered_workqueue(KBUILD_MODNAME,
> WQ_HIGHPRI);
> > + if (!data->workqueue) {
> > + BT_ERR("Failed to create workqueue");
> > + return -ENOMEM;
> > + }
> > + skb_queue_head_init(&data->rx_skb_q);
> > + INIT_WORK(&data->rx_work, btintel_pcie_rx_work);
> > +
> > + data->boot_stage_cache = 0x00;
> > + data->img_resp_cache = 0x00;
> > +
> > + /* PCIe specific all to configure it for this device includes
> > + * enabling pice device, setting master, reading BAR[0], configuring
> > + * MSIx, setting DMA mask, and save the driver data.
> > + */
> > + err = btintel_pcie_config_pcie(pdev, data);
> > + if (err) {
> > + BT_ERR("Failed to config pcie (%d)", err);
> > + goto exit_error;
> > + }
> > +
> > + /* Set driver data for this PCI device */
> > + pci_set_drvdata(pdev, data);
> > +
> > + /* allocate the IPC struct */
> > + err = btintel_pcie_alloc(data);
> > + if (err) {
> > + BT_ERR("Failed to allocate queues(%d)", err);
> > + goto exit_error;
> > + }
> > +
> > + /* Enable BT function */
> > + err = btintel_pcie_enable_bt(data);
> > + if (err) {
> > + BT_ERR("Failed to start bluetooth device(%d)", err);
> > + goto exit_error;
> > + }
> > +
> > + /* CNV information (CNVi and CNVr) is in CSR */
> > + data->cnvi = btintel_pcie_rd_reg32(data, CSR_HW_REV_REG);
> > + BT_DBG("cnvi: 0x%08x", data->cnvi);
> > +
> > + data->cnvr = btintel_pcie_rd_reg32(data, CSR_RF_ID_REG);
> > + BT_DBG("cnvr: 0x%08x", data->cnvr);
> > +
> > + err = btintel_pcie_start_rx(data);
> > + if (err) {
> > + BT_ERR("Failed to start rx (%d)", err);
> > + goto exit_error;
> > + }
> > +
> > + err = btintel_pcie_setup_hdev(data);
> > + if (err) {
> > + BT_ERR("Failed to setup HCI module");
> > + goto exit_error;
> > + }
> > +
> > + return 0;
> > +
> > +exit_error:
> > + /* reset device before leave */
> > + btintel_pcie_reset_bt(data);
> > +
> > + /* clear bus mastering */
> > + pci_clear_master(pdev);
> > +
> > + /* Unset driver data for PCI device */
> > + pci_set_drvdata(pdev, NULL);
> > +
> > + return err;
> > +}
> > +
> > +static void btintel_pcie_remove(struct pci_dev *pdev)
> > +{
> > + struct btintel_pcie_data *data;
> > +
> > + if (!pdev) {
> > + BT_ERR("Invalid parameter: pdev");
> > + return;
> > + }
> > +
> > + data = pci_get_drvdata(pdev);
> > + if (!data) {
> > + BT_ERR("data is empty");
> > + return;
> > + }
> > +
> > + btintel_pcie_release_hdev(data);
> > +
> > + flush_work(&data->rx_work);
> > +
> > + destroy_workqueue(data->workqueue);
> > +
> > + btintel_pcie_free(data);
> > +
> > + /* reset device before leave */
> > + btintel_pcie_reset_bt(data);
> > +
> > + /* clear bus mastering */
> > + pci_clear_master(pdev);
> > +
> > + /* Unset driver data for PCI device */
> > + pci_set_drvdata(pdev, NULL);
> > +}
> > +
> > +#ifdef CONFIG_PM
> > +static int btintel_pcie_suspend(struct device *dev)
> > +{
> > + /* TODO: Add support suspend */
> > + return 0;
> > +}
> > +
> > +static int btintel_pcie_resume(struct device *dev)
> > +{
> > + /* TODO: Add support resume */
> > + return 0;
> > +}
> > +
> > +static SIMPLE_DEV_PM_OPS(btintel_pcie_pm_ops, btintel_pcie_suspend,
> > + btintel_pcie_resume);
> > +#endif /* CONFIG_PM */
> > +
> > +static struct pci_driver btintel_pcie_driver = {
> > + .name = KBUILD_MODNAME,
> > + .id_table = btintel_pcie_table,
> > + .probe = btintel_pcie_probe,
> > + .remove = btintel_pcie_remove,
> > +#ifdef CONFIG_PM
> > + .driver.pm = &btintel_pcie_pm_ops,
> > +#endif /* CONFIG_PM */
> > +};
> > +module_pci_driver(btintel_pcie_driver);
> > +
> > +MODULE_AUTHOR("Tedd Ho-Jeong An <tedd.an@intel.com>");
> > +MODULE_DESCRIPTION("Intel Bluetooth PCIe transport driver ver "
> VERSION);
> > +MODULE_VERSION(VERSION);
> > +MODULE_LICENSE("GPL");
> > diff --git a/drivers/bluetooth/btintel_pcie.h
> b/drivers/bluetooth/btintel_pcie.h
> > new file mode 100644
> > index 000000000000..1554964686bd
> > --- /dev/null
> > +++ b/drivers/bluetooth/btintel_pcie.h
> > @@ -0,0 +1,449 @@
> > +/* SPDX-License-Identifier: GPL-2.0-or-later */
> > +/*
> > + * Intel Bluetooth PCIE driver
> > + *
> > + * Copyright (C) 2017 Intel Corporation. All rights reserved.
> > + *
> > + * This program is free software; you can redistribute it and/or
> > + * modify it under the terms of the GNU General Public License version
> > + * 2 as published by the Free Software Foundation.
> > + *
> > + * This program is distributed in the hope that it will be useful,
> > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> > + * GNU General Public License for more details.
> > + *
> > + * Copyright (C) 2022 Intel Corporation
>
> Ditto.
Ack.
>
> > + *
> > + * Intel Bluetooth Driver for PCIE interface.
> > + */
> > +
> > +/* Control and Status Register(CSR) */
> > +#define CSR_BASE (0x000)
> > +#define CSR_FUNC_CTRL_REG (CSR_BASE + 0x024)
> > +#define CSR_HW_REV_REG (CSR_BASE + 0x028)
> > +#define CSR_RF_ID_REG (CSR_BASE + 0x09C)
> > +#define CSR_BOOT_STAGE_REG (CSR_BASE + 0x108)
> > +#define CSR_CI_ADDR_LSB_REG (CSR_BASE + 0x118)
> > +#define CSR_CI_ADDR_MSB_REG (CSR_BASE + 0x11C)
> > +#define CSR_IMG_RESPONSE_REG (CSR_BASE + 0x12C)
> > +#define CSR_HBUS_TARG_WRPTR (CSR_BASE + 0x460)
> > +
> > +/* CSR Function Control Register */
> > +#define CSR_FUNC_CTRL_FUNC_ENA (BIT(0))
> > +#define CSR_FUNC_CTRL_MAC_INIT (BIT(6))
> > +#define CSR_FUNC_CTRL_FUNC_INIT (BIT(7))
> > +#define CSR_FUNC_CTRL_MAC_ACCESS_STS (BIT(20))
> > +#define CSR_FUNC_CTRL_SW_RESET (BIT(31))
> > +
> > +/* Value for CSR_BOOT_STAGE register */
> > +#define CSR_BOOT_STAGE_ROM (BIT(0))
> > +#define CSR_BOOT_STAGE_IML (BIT(1))
> > +#define CSR_BOOT_STAGE_OPFW (BIT(2))
> > +#define CSR_BOOT_STAGE_ROM_LOCKDOWN (BIT(10))
> > +#define CSR_BOOT_STAGE_IML_LOCKDOWN (BIT(11))
> > +#define CSR_BOOT_STAGE_MAC_ACCESS_ON (BIT(16))
> > +#define CSR_BOOT_STAGE_ALIVE (BIT(23))
> > +
> > +/* Registers for MSIX */
> > +#define CSR_MSIX_BASE (0x2000)
> > +#define CSR_MSIX_FH_INT_CAUSES (CSR_MSIX_BASE + 0x0800)
> > +#define CSR_MSIX_FH_INT_MASK (CSR_MSIX_BASE + 0x0804)
> > +#define CSR_MSIX_HW_INT_CAUSES (CSR_MSIX_BASE +
> 0x0808)
> > +#define CSR_MSIX_HW_INT_MASK (CSR_MSIX_BASE + 0x080C)
> > +#define CSR_MSIX_AUTOMASK_ST (CSR_MSIX_BASE + 0x0810)
> > +#define CSR_MSIX_AUTOMASK_EN (CSR_MSIX_BASE + 0x0814)
> > +#define CSR_MSIX_IVAR_BASE (CSR_MSIX_BASE + 0x0880)
> > +#define CSR_MSIX_IVAR(cause) (CSR_MSIX_IVAR_BASE +
> (cause))
> > +
> > +/* Causes for the FH register interrupts */
> > +enum msix_fh_int_causes {
> > + MSIX_FH_INT_CAUSES_0 = BIT(0), /* cause 0 */
> > + MSIX_FH_INT_CAUSES_1 = BIT(1), /* cause 1 */
> > +};
> > +
> > +/* Causes for the HW register interrupts */
> > +enum msix_hw_int_causes {
> > + MSIX_HW_INT_CAUSES_GP0 = BIT(0), /* cause 32 */
> > +};
> > +
> > +#define MSIX_NON_AUTO_CLEAR_CAUSE BIT(7)
> > +
> > +/* Minimum and Maximum number of MSIx Vector
> > + * Intel Bluetooth PCIe support only 1 vector
> > + */
> > +#define MSIX_VEC_MAX 1
> > +#define MSIX_VEC_MIN 1
> > +
> > +/* Default Poll time for MAC access during init*/
>
> Missing space at the end.
Ack.
>
> > +#define DEFAULT_MAC_ACCESS_TIMEOUT 200000
>
> Please specify the unit in the name.
>
Ack.
> > +
> > +/* Default interrupt timeout in msec */
> > +#define DEFAULT_INTR_TIMEOUT 3000
>
> Ditto.
Ack.
>
> > +
> > +/* The number of descriptors in TX/RX queues */
> > +#define DESCS_COUNT 16
> > +
> > +/* Number of Queue for TX and RX
> > + * It indicates the index of the IA(Index Array)
> > + */
> > +enum {
> > + TXQ_NUM = 0,
> > + RXQ_NUM = 1,
> > + NUM_QUEUES = 2,
> > +};
> > +
> > +/* The size of DMA buffer for TX and RX */
> > +#define BUFFER_SIZE 4096
>
> Is that bytes?
Yes. I will update the same in the above comment.
>
> > +
> > +/* DMA allocation alignment */
> > +#define DMA_POOL_ALIGNMENT 256
> > +
> > +/* TX wait time (jiffies) */
> > +#define TX_WAIT_TIMEOUT 500
>
> Please add the unit to the name.
Ack.
>
> > +
> > +/* Number of pending RX requests for downlink */
> > +#define RX_MAX_QUEUE 6
> > +
> > +/* Enum for RBD buffer size mappting */
> > +enum {
> > + RBD_SIZE_1K = 0x1,
> > + RBD_SIZE_2K = 0x2,
> > + RBD_SIZE_4K = 0x4,
> > + RBD_SIZE_8K = 0x8,
> > + RBD_SIZE_12K = 0x9,
> > + RBD_SIZE_16K = 0xA,
> > + RBD_SIZE_20K = 0xB,
> > + RBD_SIZE_24K = 0xC,
> > + RBD_SIZE_28K = 0xD,
> > + RBD_SIZE_32K = 0xE,
> > +};
> > +
> > +/*
> > + * Struct for Context Information (v2)
> > + *
> > + * All members are write-only for host and read-only for device.
> > + *
> > + * @version: Version of context information
> > + * @size: Size of context information
> > + * @config: Config with which host wants peripheral to execute
> > + * Subset of capability register published by device
> > + * @addr_tr_hia: Address of TR Head Index Array
> > + * @addr_tr_tia: Address of TR Tail Index Array
> > + * @addr_cr_hia: Address of CR Head Index Array
> > + * @addr_cr_tia: Address of CR Tail Index Array
> > + * @num_tr_ia: Number of entries in TR Index Arrays
> > + * @num_cr_ia: Number of entries in CR Index Arrays
> > + * @rbd_siz: RBD Size { 0x4=4K }
> > + * @addr_tfdq: Address of TFD Queue(tx)
> > + * @addr_urbdq0: Address of URBD Queue(tx)
> > + * @num_tfdq: Number of TFD in TFD Queue(tx)
> > + * @num_urbdq0: Number of URBD in URBD Queue(tx)
> > + * @tfdq_db_vec: Queue number of TFD
> > + * @urbdq0_db_vec: Queue number of URBD
> > + * @addr_frbdq: Address of FRBD Queue(rx)
> > + * @addr_urbdq1: Address of URBD Queue(rx)
> > + * @num_frbdq: Number of FRBD in FRBD Queue(rx)
> > + * @frbdq_db_vec: Queue number of FRBD
> > + * @num_urbdq1: Number of URBD in URBD Queue(rx)
> > + * @urbdq_db_vec: Queue number of URBDQ1
> > + * @tr_msi_vec: Transfer Ring MSI Vector
> > + * @cr_msi_vec: Completion Ring MSI Vector
> > + * @dbgc_addr: DBGC first fragmemt address
> > + * @dbgc_size: DBGC buffer size
> > + * @early_enable: Enarly debug enable
>
> Early
Ack.
>
> > + * @dbg_output_mode: Debug output mode
> > + * Bit[4] DBGC O/P { 0=SRAM, 1=DRAM(not relevant for NPK) }
> > + * Bit[5] DBGC I/P { 0=BDBG, 1=DBGI }
> > + * Bits[6:7] DBGI O/P(relevant if bit[5] = 1)
> > + * 0=BT DBGC, 1=WiFi DBGC, 2=NPK }
> > + * @dbg_preset: Debug preset
> > + * @ext_addr: Address of context information extension
> > + * @ext_size: Size of context information part
> > + *
> > + * Total 38 DWords
> > + *
> > + */
> > +struct ctx_info {
> > + u16 version;
> > + u16 size;
> > + u32 config;
> > + u32 reserved_dw02;
> > + u32 reserved_dw03;
> > + u64 addr_tr_hia;
> > + u64 addr_tr_tia;
> > + u64 addr_cr_hia;
> > + u64 addr_cr_tia;
> > + u16 num_tr_ia;
> > + u16 num_cr_ia;
> > + u32 rbd_size:4,
> > + reserved_dw13:28;
> > + u64 addr_tfdq;
> > + u64 addr_urbdq0;
> > + u16 num_tfdq;
> > + u16 num_urbdq0;
> > + u16 tfdq_db_vec;
> > + u16 urbdq0_db_vec;
> > + u64 addr_frbdq;
> > + u64 addr_urbdq1;
> > + u16 num_frbdq;
> > + u16 frbdq_db_vec;
> > + u16 num_urbdq1;
> > + u16 urbdq_db_vec;
> > + u16 tr_msi_vec;
> > + u16 cr_msi_vec;
> > + u32 reserved_dw27;
> > + u64 dbgc_addr;
> > + u32 dbgc_size;
> > + u32 early_enable:1,
> > + reserved_dw31:3,
> > + dbg_output_mode:4,
> > + dbg_preset:8,
> > + reserved2_dw31:16;
> > + u64 ext_addr;
> > + u32 ext_size;
> > + u32 test_param;
> > + u32 reserved_dw36;
> > + u32 reserved_dw37;
> > +} __packed;
> > +
> > +/* Transfer Descriptor for TX
> > + * @type: Not in use. Set to 0x0
> > + * @size: Size of data in the buffer
> > + * @addr: DMA Address of buffer
> > + */
> > +struct tfd {
> > + u8 type;
> > + u16 size;
> > + u8 reserved;
> > + u64 addr;
> > + u32 reserved1;
> > +} __packed;
> > +
> > +/* URB Descriptor for TX
> > + * @tfd_index: Index of TFD in TFDQ + 1
> > + * @num_txq: Queue index of TFD Queue
> > + * @cmpl_count: Completion count. Always 0x01
> > + * @immediate_cmpl: Immediate completion flag: Always 0x01
> > + */
> > +struct urbd0 {
> > + u32 tfd_index:16,
> > + num_txq:8,
> > + cmpl_count:4,
> > + reserved:3,
> > + immediate_cmpl:1;
> > +} __packed;
> > +
> > +/* FRB Descriptor for RX
> > + * @tag: RX buffer tag (index of RX buffer queue)
> > + * @addr: Address of buffer
> > + */
> > +struct frbd {
> > + u32 tag:16,
> > + reserved:16;
> > + u32 reserved2;
> > + u64 addr;
> > +} __packed;
> > +
> > +/* URB Descriptor for RX
> > + * @frbd_tag: Tag from FRBD
> > + * @status: Status
> > + */
> > +struct urbd1 {
> > + u32 frbd_tag:16,
> > + status:1,
> > + reserved:14,
> > + fixed:1;
> > +} __packed;
> > +
> > +/* RFH header in RX packet
> > + * @packet_len: Length of the data in the buffer
> > + * @rxq: RX Queue number
> > + * @cmd_id: Command ID. Not in Use
> > + */
> > +struct rfh_hdr {
> > + u64 packet_len:16,
> > + rxq:6,
> > + reserved:10,
> > + cmd_id:16,
> > + reserved1:16;
> > +} __packed;
> > +
> > +/* Internal data buffer
> > + * @data: pointer to the data buffer
> > + * @p_addr: physical address of data buffer
> > + */
> > +struct data_buf {
> > + u8 *data;
> > + dma_addr_t data_p_addr;
> > +};
> > +
> > +/* Index Array */
> > +struct ia {
> > + dma_addr_t tr_hia_p_addr;
> > + u16 *tr_hia;
> > + dma_addr_t tr_tia_p_addr;
> > + u16 *tr_tia;
> > + dma_addr_t cr_hia_p_addr;
> > + u16 *cr_hia;
> > + dma_addr_t cr_tia_p_addr;
> > + u16 *cr_tia;
> > +};
> > +
> > +/* Structure for TX Queue
> > + * @count: Number of descriptors
> > + * @tfds: Array of TFD
> > + * @urbd0s: Array of URBD0
> > + * @buf: Array of data_buf structure
> > + */
> > +struct txq {
> > + u16 count;
> > +
> > + dma_addr_t tfds_p_addr;
> > + struct tfd *tfds;
> > +
> > + dma_addr_t urbd0s_p_addr;
> > + struct urbd0 *urbd0s;
> > +
> > + dma_addr_t buf_p_addr;
> > + void *buf_v_addr;
> > + struct data_buf *bufs;
> > +};
> > +
> > +/* Structure for RX Queue
> > + * @count: Number of descriptors
> > + * @frbds: Array of FRBD
> > + * @urbd1s: Array of URBD1
> > + * @buf: Array of data_buf structure
> > + */
> > +struct rxq {
> > + u16 count;
> > +
> > + dma_addr_t frbds_p_addr;
> > + struct frbd *frbds;
> > +
> > + dma_addr_t urbd1s_p_addr;
> > + struct urbd1 *urbd1s;
> > +
> > + dma_addr_t buf_p_addr;
> > + void *buf_v_addr;
> > + struct data_buf *bufs;
> > +};
> > +
> > +/* struct btintel_pcie_data
> > + * @pdev: pci device
> > + * @hdev: hdev device
> > + * @flags: driver state
> > + * @irq_lock: spinlock for MSIX
> > + * @hci_rx_lock: spinlock for HCI RX flow
> > + * @base_addr: pci base address (from BAR)
> > + * @msix_entries: array of MSIX entries
> > + * @msix_enabled: true if MSIX is enabled;
> > + * @alloc_vecs: number of interrupt vectors allocated
> > + * @def_irq: default irq for all causes
> > + * @fh_init_mask: initial unmasked rxq causes
> > + * @hw_init_mask: initial unmaksed hw causes
> > + * @boot_stage_cache: cached value of boot stage register
> > + * @img_resp_cache: cached value of image response register
> > + * @cnvi: CNVi register value
> > + * @cnvr: CNVr register value
> > + * @gp0_received: condition for gp0 interrupt
> > + * @gp0_wait_q: wait_q for gp0 interrupt
> > + * @tx_wait_done: condition for tx interrupt
> > + * @tx_wait_q: wait_q for tx interrupt
> > + * @workqueue: workqueue for RX work
> > + * @rx_skb_q: SKB queue for RX packet
> > + * @rx_work: RX work struct to process the RX packet in @rx_skb_q
> > + * @dma_pool: DMA pool for descriptors, index array and ci
> > + * @dma_p_addr: DMA address for pool
> > + * @dma_v_addr: address of pool
> > + * @ci_p_addr: DMA address for CI struct
> > + * @ci: CI struct
> > + * @ia: Index Array struct
> > + * @txq: TX Queue struct
> > + * @rxq: RX Queue struct
> > + */
> > +struct btintel_pcie_data {
> > + struct pci_dev *pdev;
> > + struct hci_dev *hdev;
> > +
> > + unsigned long flags;
> > + /* lock used in MSIX interrupt */
> > + spinlock_t irq_lock;
> > + /* lock to serialize rx events */
> > + spinlock_t hci_rx_lock;
> > +
> > + void __iomem *base_addr;
> > +
> > + struct msix_entry msix_entries[MSIX_VEC_MAX];
> > + bool msix_enabled;
> > + u32 alloc_vecs;
> > + u32 def_irq;
> > +
> > + u32 fh_init_mask;
> > + u32 hw_init_mask;
> > +
> > + u32 boot_stage_cache;
> > + u32 img_resp_cache;
> > +
> > + u32 cnvi;
> > + u32 cnvr;
> > +
> > + bool gp0_received;
> > + wait_queue_head_t gp0_wait_q;
> > +
> > + bool tx_wait_done;
> > + wait_queue_head_t tx_wait_q;
> > +
> > + struct workqueue_struct *workqueue;
> > + struct sk_buff_head rx_skb_q;
> > + struct work_struct rx_work;
> > +
> > + struct dma_pool *dma_pool;
> > + dma_addr_t dma_p_addr;
> > + void *dma_v_addr;
> > +
> > + dma_addr_t ci_p_addr;
> > + struct ctx_info *ci;
> > + struct ia ia;
> > + struct txq txq;
> > + struct rxq rxq;
> > +};
> > +
> > +static inline u32 btintel_pcie_rd_reg32(struct btintel_pcie_data *data,
> > + u32 offset)
> > +{
> > + return ioread32(data->base_addr + offset);
> > +}
> > +
> > +static inline void btintel_pcie_wr_reg8(struct btintel_pcie_data *data,
> > + u32 offset, u8 val)
> > +{
> > + iowrite8(val, data->base_addr + offset);
> > +}
> > +
> > +static inline void btintel_pcie_wr_reg32(struct btintel_pcie_data *data,
> > + u32 offset, u32 val)
> > +{
> > + iowrite32(val, data->base_addr + offset);
> > +}
> > +
> > +static inline void btintel_pcie_set_reg_bits(struct btintel_pcie_data *data,
> > + u32 offset, u32 bits)
> > +{
> > + u32 r;
> > +
> > + r = ioread32(data->base_addr + offset);
> > + r |= bits;
> > + iowrite32(r, data->base_addr + offset);
> > +}
> > +
> > +static inline void btintel_pcie_clr_reg_bits(struct btintel_pcie_data *data,
> > + u32 offset, u32 bits)
> > +{
> > + u32 r;
> > +
> > + r = ioread32(data->base_addr + offset);
> > + r &= ~bits;
> > + iowrite32(r, data->base_addr + offset);
> > +}
>
>
> Kind regards,
>
> Paul
Thanks,
Kiran
^ permalink raw reply [flat|nested] 16+ messages in thread* Re: [PATCH v1 2/3] Bluetooth: btintel_pcie: Add support for PCIE transport
2024-05-07 13:34 ` K, Kiran
@ 2024-05-07 20:28 ` Luiz Augusto von Dentz
0 siblings, 0 replies; 16+ messages in thread
From: Luiz Augusto von Dentz @ 2024-05-07 20:28 UTC (permalink / raw)
To: K, Kiran
Cc: Paul Menzel, Von Dentz, Luiz, linux-bluetooth@vger.kernel.org,
Srivatsa, Ravishankar, Tumkur Narayan, Chethan, An, Tedd,
linux-pci@vger.kernel.org
Hi Kiran,
On Tue, May 7, 2024 at 9:48 AM K, Kiran <kiran.k@intel.com> wrote:
>
> Hi Paul,
>
> Appreciate your comments :).
>
> > -----Original Message-----
> > From: Paul Menzel <pmenzel@molgen.mpg.de>
> > Sent: Thursday, March 28, 2024 5:55 PM
> > To: K, Kiran <kiran.k@intel.com>
> > Cc: linux-bluetooth@vger.kernel.org; Srivatsa, Ravishankar
> > <ravishankar.srivatsa@intel.com>; Tumkur Narayan, Chethan
> > <chethan.tumkur.narayan@intel.com>; An, Tedd <tedd.an@intel.com>; linux-
> > pci@vger.kernel.org
> > Subject: Re: [PATCH v1 2/3] Bluetooth: btintel_pcie: Add support for PCIE
> > transport
> >
> > Dear Tedd, dear Kiran,
> >
> >
> > Thank you for the patch. What a diffstat. ;-) Nice work.
> >
> > Am 28.03.24 um 12:19 schrieb Kiran K:
> > > From: Tedd Ho-Jeong An <tedd.an@intel.com>
> > >
> > > Add initial code to support Intel bluetooth devices based on PICE
> > > transport. This patch allocates memory for buffers, internal structures,
> > > initializes interrupts for TX & RX and initializes PCIE device.
> >
> > For a 1782 diffstat this is quite terse. Could you elaborate?
> >
> > Also, it’d be great if you mentioned the datasheet, and how you tested
> > this. Maybe even paste the new log messages.
> >
> Datasheet details are internal to Intel. Sorry I can't provide those details. But surely I will add kernel logs and output of hciconfig -a.
>
> > Also how well does the driver perform? What tools did you run to verify
> > the correctness und the “speed”?
> This driver has been tested on silicon (BT Filmore Peak2). Not sure of any tools to test the speed. Pls suggest if any. I will run the same and share the data.
> >
> > > Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
> > > Co-developed-by: Kiran K <kiran.k@intel.com>
> > > Signed-off-by: Kiran K <kiran.k@intel.com>
> > > ---
> > > drivers/bluetooth/Kconfig | 14 +
> > > drivers/bluetooth/Makefile | 1 +
> > > drivers/bluetooth/btintel.h | 2 +-
> > > drivers/bluetooth/btintel_pcie.c | 1317
> > ++++++++++++++++++++++++++++++
> > > drivers/bluetooth/btintel_pcie.h | 449 ++++++++++
> > > 5 files changed, 1782 insertions(+), 1 deletion(-)
> > > create mode 100644 drivers/bluetooth/btintel_pcie.c
> > > create mode 100644 drivers/bluetooth/btintel_pcie.h
> >
> > Should an entry be added to `MAINTAINERS`? It’d be good to mention in
> > the commit message, who the maintainer is.
> Individual files under drivers/bluetooth/ are not updated in MAINTAINERS. There is "F: drivers/bluetooth/" entry present. I haven't added any files in the past.
> @Von Dentz, Luiz - Any comments here ?
That should fallback to driver/bluetooth/ maintainers so it should be
fine since myself and Marcel are listed there.
>
> >
> > >
> > > diff --git a/drivers/bluetooth/Kconfig b/drivers/bluetooth/Kconfig
> > > index bc211c324206..387f7b14461d 100644
> > > --- a/drivers/bluetooth/Kconfig
> > > +++ b/drivers/bluetooth/Kconfig
> > > @@ -23,6 +23,20 @@ config BT_MTK
> > > tristate
> > > select FW_LOADER
> > >
> > > +config BT_INTEL_PCIE
> > > + tristate "Intel Bluetooth transport driver for PCIe"
> >
> > In the commit message summary you spell it PCIE. Please be consistent.
> >
> Ack.
>
> > > + depends on PCI
> > > + select BT_INTEL
> > > + select FW_LOADER
> > > + default y
> > > + help
> > > + Intel Bluetooth transport driver for PCIe.
> > > + This driver is required if you want to use Intel Bluetooth device
> > > + with PCIe interface.
> > > +
> > > + Say Y here to compiler support for Intel Bluetooth PCIe device into
> > > + the kernel or say M to compile it as module (btintel_pcie)
> > > +
> > > config BT_HCIBTUSB
> > > tristate "HCI USB driver"
> > > depends on USB
> > > diff --git a/drivers/bluetooth/Makefile b/drivers/bluetooth/Makefile
> > > index 7a5967e9ac48..0730d6684d1a 100644
> > > --- a/drivers/bluetooth/Makefile
> > > +++ b/drivers/bluetooth/Makefile
> > > @@ -17,6 +17,7 @@ obj-$(CONFIG_BT_HCIBTUSB) += btusb.o
> > > obj-$(CONFIG_BT_HCIBTSDIO) += btsdio.o
> > >
> > > obj-$(CONFIG_BT_INTEL) += btintel.o
> > > +obj-$(CONFIG_BT_INTEL_PCIE) += btintel_pcie.o btintel.o
> > > obj-$(CONFIG_BT_ATH3K) += ath3k.o
> > > obj-$(CONFIG_BT_MRVL) += btmrvl.o
> > > obj-$(CONFIG_BT_MRVL_SDIO) += btmrvl_sdio.o
> > > diff --git a/drivers/bluetooth/btintel.h b/drivers/bluetooth/btintel.h
> > > index 1462a57420a0..5d4685b5c1fa 100644
> > > --- a/drivers/bluetooth/btintel.h
> > > +++ b/drivers/bluetooth/btintel.h
> > > @@ -209,7 +209,7 @@ struct btintel_data {
> > > #define btintel_wait_on_flag_timeout(hdev, nr, m, to)
> > \
> > > wait_on_bit_timeout(btintel_get_flag(hdev), (nr), m, to)
> > >
> > > -#if IS_ENABLED(CONFIG_BT_INTEL)
> > > +#if IS_ENABLED(CONFIG_BT_INTEL) ||
> > IS_ENABLED(CONFIG_BT_INTEL_PCIE)
> > >
> > > int btintel_check_bdaddr(struct hci_dev *hdev);
> > > int btintel_enter_mfg(struct hci_dev *hdev);
> > > diff --git a/drivers/bluetooth/btintel_pcie.c
> > b/drivers/bluetooth/btintel_pcie.c
> > > new file mode 100644
> > > index 000000000000..e6ce2304dc57
> > > --- /dev/null
> > > +++ b/drivers/bluetooth/btintel_pcie.c
> > > @@ -0,0 +1,1317 @@
> > > +// SPDX-License-Identifier: GPL-2.0-or-later
> > > +/*
> > > + * Intel Bluetooth PCIE driver
> > > + *
> > > + * Copyright (C) 2017 Intel Corporation. All rights reserved.
> > > + *
> > > + * This program is free software; you can redistribute it and/or
> > > + * modify it under the terms of the GNU General Public License version
> > > + * 2 as published by the Free Software Foundation.
> > > + *
> > > + * This program is distributed in the hope that it will be useful,
> > > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> > > + * GNU General Public License for more details.
> > > + *
> > > + * Copyright (C) 2022 Intel Corporation
> >
> > Are two copyright lines needed?
> >
> No. I overlooked this. I will fix in v2 version.
> > > + *
> > > + * Intel Bluetooth Driver for PCIE interface.
> > > + */
> > > +#include <linux/kernel.h>
> > > +#include <linux/module.h>
> > > +#include <linux/firmware.h>
> > > +#include <linux/pci.h>
> > > +#include <linux/wait.h>
> > > +#include <linux/delay.h>
> > > +#include <linux/interrupt.h>
> > > +
> > > +#include <asm/unaligned.h>
> > > +
> > > +#include <net/bluetooth/bluetooth.h>
> > > +#include <net/bluetooth/hci_core.h>
> > > +
> > > +#include "btintel.h"
> > > +#include "btintel_pcie.h"
> > > +
> > > +#define VERSION "0.1"
> > > +
> > > +#define BTINTEL_PCI_DEVICE(dev, subdev) \
> > > + .vendor = PCI_VENDOR_ID_INTEL, \
> > > + .device = (dev), \
> > > + .subvendor = PCI_ANY_ID, \
> > > + .subdevice = (subdev), \
> > > + .driver_data = 0
> > > +
> > > +/* Intel Bluetooth PCIe device id table */
> > > +static const struct pci_device_id btintel_pcie_table[] = {
> > > + { BTINTEL_PCI_DEVICE(0xA876, PCI_ANY_ID) },
> > > + { 0 }
> > > +};
> > > +MODULE_DEVICE_TABLE(pci, btintel_pcie_table);
> > > +
> > > +/* Intel PCIe uses 4 bytes of HCI type instead of 1 byte BT SIG HCI type */
> > > +#define BTINTEL_PCIE_HCI_TYPE_LEN 4
> > > +#define BTINTEL_PCIE_HCI_CMD_PKT 0x00000001
> > > +#define BTINTEL_PCIE_HCI_ACL_PKT 0x00000002
> > > +#define BTINTEL_PCIE_HCI_SCO_PKT 0x00000003
> > > +#define BTINTEL_PCIE_HCI_EVT_PKT 0x00000004
> > > +
> > > +#define BTITNEL_PCIE_ENABLE_HCI_DUMP 0
> >
> > Mention this macro in the commit message?
> I will remove this macro as we have monitor to dump all the HCI traffic.
> >
> > > +
> > > +#if BTITNEL_PCIE_ENABLE_HCI_DUMP
> > > +static inline void btintel_pcie_hci_dump(const char *p, const void *b, int s)
> > > +{
> > > + const unsigned char *ptr = (const unsigned char *)b;
> > > + char str[64];
> > > + int c, i;
> > > +
> > > + for (i = c = 0; c < s; c++) {
> > > + i += snprintf(str + i, sizeof(str) - i, "%02x ", ptr[c]);
> > > + if ((c > 0 && (c + 1) % 8 == 0) || (c == s - 1)) {
> > > + BT_DBG("%s: %s", p, str);
> > > + i = 0;
> > > + }
> > > + }
> > > +}
> > > +#else
> > > +static inline void btintel_pcie_hci_dump(const char *p, const void *b, int s)
> > > +{
> > > +}
> > > +#endif
> >
> > Is there a way to test this code, that means some CI setting
> > `BTITNEL_PCIE_ENABLE_HCI_DUMP`? Would the linker remove unneeded
> > code,
> > if you did
> >
> > static inline void btintel_pcie_hci_dump(const char *p, const void
> > *b, int s)
> > {
> > if (BTITNEL_PCIE_ENABLE_HCI_DUMP) {
> > Everything here.
> > }
> > }
> >
> > > +
> > > +static void ipc_print_ia_ring(struct ia *ia, u16 queue_num)
> > > +{
> > > + BT_DBG("[%s] ---------------- ia ----------------",
> > > + queue_num == TXQ_NUM ? "TXQ" : "RXQ");
> > > + BT_DBG("[%s] tr-h:%02u tr-t:%02u cr-h:%02u cr-t:%02u",
> > > + queue_num == TXQ_NUM ? "TXQ" : "RXQ",
> > > + ia->tr_hia[queue_num], ia->tr_tia[queue_num],
> > > + ia->cr_hia[queue_num], ia->cr_tia[queue_num]);
> > > +}
> > > +
> > > +static void ipc_print_urbd0(struct urbd0 *urbd0, u16 index)
> > > +{
> > > + BT_DBG("[TXQ] -------------- urbd0[%u] --------------", index);
> > > + BT_DBG("[TXQ] tfd_index:%u num_txq:%u cmpl_cnt:%u
> > immediate_cmpl:0x%x",
> > > + urbd0->tfd_index, urbd0->num_txq, urbd0->cmpl_count,
> > > + urbd0->immediate_cmpl);
> > > +}
> > > +
> > > +static void ipc_print_frbd(struct frbd *frbd, u16 index)
> > > +{
> > > + BT_DBG("[RXQ] -------------- frbd[%u] --------------", index);
> > > + BT_DBG("[RXQ] tag:%u addr:0x%llx", frbd->tag, frbd->addr);
> > > +}
> > > +
> > > +static void ipc_print_urbd1(struct urbd1 *urbd1, u16 index)
> > > +{
> > > + BT_DBG("[RXQ] -------------- urbd1[%u] --------------", index);
> > > + BT_DBG("[RXQ] frbd_tag:%u status: 0x%x fixed:0x%x",
> > > + urbd1->frbd_tag, urbd1->status, urbd1->fixed);
> > > +}
> > > +
> > > +/* Poll internal in microseconds */
> > > +#define POLL_INTERVAL 10
> >
> > Please put the unit into the name: `POLL_INTERVAL_MS`. Then the comment
> > can also be removed as redundant.
> Ack.
> >
> > > +
> > > +static int btintel_pcie_poll_bit(struct btintel_pcie_data *data, u32 offset,
> > > + u32 bits, u32 mask, int timeout)
> >
> > Add the unit to `timeout`
> Ack.
>
> >
> > > +{
> > > + int t = 0;
> > > + u32 reg;
> > > +
> > > + BT_DBG("Enter poll_bit");
> >
> > Is this needed? Doesn’t Linux’ tracing framework cover this already?
> Ack.
> >
> > > + do {
> > > + reg = btintel_pcie_rd_reg32(data, offset);
> > > + BT_DBG("CURRENT FUNC_CTRL_REG: 0x%x", reg);
> > > +
> > > + if ((reg & mask) == (bits & mask)) {
> > > + BT_DBG("Poll bit matched");
> > > + return t;
> > > + }
> > > + udelay(POLL_INTERVAL);
> > > + t += POLL_INTERVAL;
> > > + BT_DBG("Poll wait: %d", t);
> >
> > Maybe elaborate, so it’s clear it’s the cummulative time. Maybe also
> > print `timeout` value?
> Timeout values are static. Let me know if its really required. BTW, I will remove BT_DBG logs which are not of much help.
> >
> > > + } while (t < timeout);
> > > +
> > > + return -ETIMEDOUT;
> > > +}
> > > +
> > > +static struct btintel_pcie_data *btintel_pcie_get_data(struct msix_entry
> > *entry)
> > > +{
> > > + u8 queue = entry->entry;
> > > + struct msix_entry *entries = entry - queue;
> > > +
> > > + return container_of(entries, struct btintel_pcie_data, msix_entries[0]);
> > > +}
> > > +
> > > +/* Set the doorbell for RXQ to notify the device that @index(actually index-
> > 1)
> > > + * is available to receive the data
> > > + */
> > > +static void btintel_pcie_set_rx_db(struct btintel_pcie_data *data, u16
> > index)
> > > +{
> > > + u32 val;
> > > +
> > > + val = index;
> > > + val |= (513 << 16);
> > > +
> > > + BT_DBG("[RXQ] Set doorbell for index: %u", index);
> > > + btintel_pcie_wr_reg32(data, CSR_HBUS_TARG_WRPTR, val);
> > > +}
> > > +
> > > +/* Update the FRBD(free buffer descriptor) with the @frbd_index and the
> > > + * DMA address of the free buffer.
> > > + */
> > > +static void btintel_pcie_prepare_rx(struct rxq *rxq, u16 frbd_index)
> > > +{
> > > + struct data_buf *buf;
> > > + struct frbd *frbd;
> > > +
> > > + /* Get the buffer of the frbd for DMA */
> > > + buf = &rxq->bufs[frbd_index];
> > > +
> > > + frbd = &rxq->frbds[frbd_index];
> > > + memset(frbd, 0, sizeof(*frbd));
> > > +
> > > + /* Update FRBD */
> > > + frbd->tag = frbd_index;
> > > + frbd->addr = buf->data_p_addr;
> > > + ipc_print_frbd(frbd, frbd_index);
> > > +}
> > > +
> > > +static int btintel_pcie_submit_rx(struct btintel_pcie_data *data)
> > > +{
> > > + u16 frbd_index;
> > > + struct rxq *rxq = &data->rxq;
> > > +
> > > + /* Read the frbd index from the TR_HIA(Head Index Array) for RXQ */
> > > + frbd_index = data->ia.tr_hia[RXQ_NUM];
> > > + BT_DBG("[RXQ] current frbd_index: %u", frbd_index);
> > > +
> > > + /* Make sure the index value is within the range. It shouldn't be
> > > + * bigger than the total count of the queue.
> > > + */
> > > + if (frbd_index > rxq->count) {
> > > + BT_ERR("[RXQ] RXQ out of range: (0x%x)", frbd_index);
> > > + return -ERANGE;
> > > + }
> > > +
> > > + /* Prepare for RX submit. It updates the FRBD with the address of
> > DMA
> > > + * buffer
> > > + */
> > > + btintel_pcie_prepare_rx(rxq, frbd_index);
> > > +
> > > + /* Update TR_HIA with new FRBD index */
> > > + frbd_index = (frbd_index + 1) % rxq->count;
> > > + data->ia.tr_hia[RXQ_NUM] = frbd_index;
> > > + ipc_print_ia_ring(&data->ia, RXQ_NUM);
> > > +
> > > + /* Set the doorbell to notify the device */
> > > + btintel_pcie_set_rx_db(data, frbd_index);
> > > +
> > > + BT_DBG("[RXQ] rx sumbit completed");
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static int btintel_pcie_start_rx(struct btintel_pcie_data *data)
> > > +{
> > > + int i, ret;
> > > +
> > > + for (i = 0; i < RX_MAX_QUEUE; i++) {
> > > + ret = btintel_pcie_submit_rx(data);
> > > + if (ret) {
> > > + BT_ERR("[RXQ] failed to submit frbd(%d)", ret);
> > > + return ret;
> > > + }
> > > + }
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static void btintel_pcie_reset_ia(struct btintel_pcie_data *data)
> > > +{
> > > + memset(data->ia.tr_hia, 0, sizeof(u16) * NUM_QUEUES);
> > > + memset(data->ia.tr_tia, 0, sizeof(u16) * NUM_QUEUES);
> > > + memset(data->ia.cr_hia, 0, sizeof(u16) * NUM_QUEUES);
> > > + memset(data->ia.cr_tia, 0, sizeof(u16) * NUM_QUEUES);
> > > + BT_DBG("Index Arrays are reset");
> > > +}
> > > +
> > > +static void btintel_pcie_reset_bt(struct btintel_pcie_data *data)
> > > +{
> > > + BT_INFO("Reset BT Function ");
> > > + btintel_pcie_wr_reg32(data, CSR_FUNC_CTRL_REG,
> > CSR_FUNC_CTRL_SW_RESET);
> > > +}
> > > +
> > > +/* This function enables BT function by setting CSR_FUNC_CTRL_MAC_INIT
> > bit in
> > > + * CSR_FUNC_CTRL_REG register and wait for MSI-X with
> > MSIX_HW_INT_CAUSES_GP0.
> > > + * Then the host reads firmware version from CSR_F2D_MBX and the boot
> > stage
> > > + * from CSR_BOOT_STAGE_REG.
> > > + */
> > > +static int btintel_pcie_enable_bt(struct btintel_pcie_data *data)
> > > +{
> > > + int err;
> > > + u32 reg;
> > > +
> > > + data->gp0_received = false;
> > > +
> > > + /* Update the DMA address of CI struct to CSR */
> > > + btintel_pcie_wr_reg32(data, CSR_CI_ADDR_LSB_REG,
> > > + data->ci_p_addr & 0xffffffff);
> > > + btintel_pcie_wr_reg32(data, CSR_CI_ADDR_MSB_REG,
> > > + data->ci_p_addr >> 32);
> > > +
> > > + /* Reset the cached value of boot stage. it is updated by the msix
> > > + * gp0 interrupt handler.
> > > + */
> > > + data->boot_stage_cache = 0x0;
> > > +
> > > + /* Set MAC_INIT bit to start primary bootloader */
> > > + reg = btintel_pcie_rd_reg32(data, CSR_FUNC_CTRL_REG);
> > > + BT_INFO("Before: FUNC_CTRL_REG: 0x%x", reg);
> > > +
> > > + btintel_pcie_set_reg_bits(data, CSR_FUNC_CTRL_REG,
> > > + CSR_FUNC_CTRL_MAC_INIT);
> > > + BT_INFO("MAC_INIT is set");
> > > +
> > > + /* Wait until MAC_ACCESS is granted */
> > > + err = btintel_pcie_poll_bit(data, CSR_FUNC_CTRL_REG,
> > > + CSR_FUNC_CTRL_MAC_ACCESS_STS,
> > > + CSR_FUNC_CTRL_MAC_ACCESS_STS,
> > > + DEFAULT_MAC_ACCESS_TIMEOUT);
> > > + if (err < 0) {
> > > + BT_ERR("Failed to start bootloader even after %u ns",
> > > + DEFAULT_MAC_ACCESS_TIMEOUT);
> > > + return -ENODEV;
> > > + }
> > > +
> > > + /* MAC is ready. Enable BT FUNC */
> > > + btintel_pcie_set_reg_bits(data, CSR_FUNC_CTRL_REG,
> > > + CSR_FUNC_CTRL_FUNC_ENA |
> > > + CSR_FUNC_CTRL_FUNC_INIT);
> > > +
> > > + reg = btintel_pcie_rd_reg32(data, CSR_FUNC_CTRL_REG);
> > > + BT_INFO("After: FUNC_CTRL_REG: 0x%x", reg);
> > > +
> > > + /* wait for interrupt from the device after booting up to primary
> > > + * bootloader.
> > > + */
> > > + err = wait_event_timeout(data->gp0_wait_q, data->gp0_received,
> > > + msecs_to_jiffies(DEFAULT_INTR_TIMEOUT));
> > > + if (!err) {
> > > + BT_ERR("Failed to receive mac_init interrupt");
> > > + return -ETIME;
> > > + }
> > > +
> > > + /* Check cached boot stage is CSR_BOOT_STAGE_ROM(BIT(0)) */
> > > + if (~data->boot_stage_cache & CSR_BOOT_STAGE_ROM) {
> > > + BT_ERR("Device is not running in rom");
> > > + return -ENODEV;
> > > + }
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +/* This function handles the MSI-X interrupt for gp0 cause(bit 0 in
> > > + * CSR_MSIX_HW_INT_CAUSES) which is sent for boot stage and image
> > response.
> > > + */
> > > +static void btintel_pcie_msix_gp0_handler(struct btintel_pcie_data *data)
> > > +{
> > > + u32 reg;
> > > +
> > > + /* This interrupt is for three different causes and it is not easy to
> > > + * know what causes the interrupt. So, it compares each register value
> > > + * with cached value and update it before it wake up the queue.
> > > + */
> > > + reg = btintel_pcie_rd_reg32(data, CSR_BOOT_STAGE_REG);
> > > + if (reg != data->boot_stage_cache) {
> > > + data->boot_stage_cache = reg;
> > > +
> > > + BT_DBG("Boot Stage updated: 0x%x", reg);
> > > + }
> > > +
> > > + reg = btintel_pcie_rd_reg32(data, CSR_IMG_RESPONSE_REG);
> > > + if (reg != data->img_resp_cache) {
> > > + data->img_resp_cache = reg;
> > > +
> > > + BT_DBG("Image Response updated: 0x%x", reg);
> > > + }
> > > +
> > > + BT_DBG("---------- cached GP0 registers ----------");
> > > + BT_DBG("Cached Boot Stage Reg: 0x%x", data->boot_stage_cache);
> > > + BT_DBG("Cached Image Resp Reg: 0x%x", data->img_resp_cache);
> > > +
> > > + data->gp0_received = true;
> > > +
> > > + /* If the boot stage is OP or IML, reset IA and start RX again */
> > > + if (data->boot_stage_cache & CSR_BOOT_STAGE_OPFW ||
> > > + data->boot_stage_cache & CSR_BOOT_STAGE_IML) {
> > > + btintel_pcie_reset_ia(data);
> > > + btintel_pcie_start_rx(data);
> > > + }
> > > +
> > > + wake_up(&data->gp0_wait_q);
> > > +}
> > > +
> > > +/* This function handles the MSX-X interrupt for rx queue 0 which is for TX
> > > + */
> > > +static void btintel_pcie_msix_tx_handle(struct btintel_pcie_data *data)
> > > +{
> > > + u16 cr_tia, cr_hia;
> > > + struct txq *txq;
> > > + struct urbd0 *urbd0;
> > > +
> > > + cr_tia = data->ia.cr_tia[TXQ_NUM];
> > > + cr_hia = data->ia.cr_hia[TXQ_NUM];
> > > +
> > > + BT_DBG("[TXQ] cr_hia=%u cr_tia=%u", cr_hia, cr_tia);
> > > +
> > > + /* Check CR_TIA and CR_HIA for change */
> > > + if (cr_tia == cr_hia) {
> > > + BT_ERR("[TXQ] no new CD found");
> > > + return;
> > > + }
> > > +
> > > + txq = &data->txq;
> > > +
> > > + while (cr_tia != cr_hia) {
> > > + BT_DBG("[TXQ] wake up tx_wait_q");
> > > +
> > > + data->tx_wait_done = true;
> > > + wake_up(&data->tx_wait_q);
> > > +
> > > + /* Get URBD0 pointed by cr_tia */
> > > + urbd0 = &txq->urbd0s[cr_tia];
> > > + ipc_print_urbd0(urbd0, cr_tia);
> > > +
> > > + /* Make sure the completed TFD index is within the range */
> > > + if (urbd0->tfd_index > txq->count) {
> > > + BT_ERR("[TXQ] out of range: (0x%x)", urbd0-
> > >tfd_index);
> > > + return;
> > > + }
> > > +
> > > + /* Increase cr_tia */
> > > + cr_tia = (cr_tia + 1) % txq->count;
> > > + data->ia.cr_tia[TXQ_NUM] = cr_tia;
> > > + ipc_print_ia_ring(&data->ia, TXQ_NUM);
> > > + }
> > > +}
> > > +
> > > +static int btintel_pcie_recv_event_intel(struct hci_dev *hdev,
> > > + struct sk_buff *skb)
> > > +{
> > > + if (btintel_test_flag(hdev, INTEL_BOOTLOADER)) {
> > > + struct hci_event_hdr *hdr = (void *)skb->data;
> > > +
> > > + if (skb->len > HCI_EVENT_HDR_SIZE && hdr->evt == 0xff &&
> > > + hdr->plen > 0) {
> > > + const void *ptr = skb->data + HCI_EVENT_HDR_SIZE +
> > 1;
> > > + unsigned int len = skb->len - HCI_EVENT_HDR_SIZE -
> > 1;
> > > +
> > > + switch (skb->data[2]) {
> > > + case 0x02:
> > > + /* When switching to the operational
> > firmware
> > > + * the device sends a vendor specific event
> > > + * indicating that the bootup completed.
> > > + */
> > > + btintel_bootup(hdev, ptr, len);
> > > + break;
> > > + case 0x06:
> > > + /* When the firmware loading completes the
> > > + * device sends out a vendor specific event
> > > + * indicating the result of the firmware
> > > + * loading.
> > > + */
> > > + btintel_secure_send_result(hdev, ptr, len);
> > > + break;
> > > + }
> > > + }
> > > + }
> > > +
> > > + return hci_recv_frame(hdev, skb);
> > > +}
> > > +
> > > +/* Process the received rx data
> > > + * It check the frame header to identify the data type and create skb
> > > + * and calling HCI API
> > > + */
> > > +static int btintel_pcie_hci_recv_frame(struct btintel_pcie_data *data,
> > > + void *buf, int count)
> > > +{
> > > + struct hci_dev *hdev = data->hdev;
> > > + int ret;
> > > + u32 pkt_type;
> > > + u16 plen;
> > > + struct sk_buff *skb;
> > > +
> > > + spin_lock(&data->hci_rx_lock);
> > > +
> > > + /* The first 4 bytes indicates the Intel PCIe specific packet type.
> > > + * Read the packet type here before remove it.
> > > + */
> > > + pkt_type = get_unaligned_le32(buf);
> > > + bt_dev_dbg(hdev, "pkt_type=%u count=%d", pkt_type, count);
> > > +
> > > + buf += BTINTEL_PCIE_HCI_TYPE_LEN;
> > > + count -= BTINTEL_PCIE_HCI_TYPE_LEN;
> > > +
> > > + hdev->stat.byte_rx += count;
> > > +
> > > + skb = bt_skb_alloc(count, GFP_ATOMIC);
> > > + if (!skb) {
> > > + bt_dev_err(hdev, "Failed to allocate skb for event");
> > > + ret = -ENOMEM;
> > > + goto exit_error;
> > > + }
> > > +
> > > + switch (pkt_type) {
> > > + case BTINTEL_PCIE_HCI_ACL_PKT:
> > > + hci_skb_pkt_type(skb) = HCI_ACLDATA_PKT;
> > > + memcpy(skb_put(skb, HCI_ACL_HDR_SIZE), buf,
> > HCI_ACL_HDR_SIZE);
> > > + plen = hci_acl_hdr(skb)->dlen;
> > > + buf += HCI_ACL_HDR_SIZE;
> > > + break;
> > > + case BTINTEL_PCIE_HCI_SCO_PKT:
> > > + hci_skb_pkt_type(skb) = HCI_SCODATA_PKT;
> > > + memcpy(skb_put(skb, HCI_SCO_HDR_SIZE), buf,
> > HCI_SCO_HDR_SIZE);
> > > + plen = hci_sco_hdr(skb)->dlen;
> > > + buf += HCI_SCO_HDR_SIZE;
> > > + break;
> > > + case BTINTEL_PCIE_HCI_EVT_PKT:
> > > + hci_skb_pkt_type(skb) = HCI_EVENT_PKT;
> > > + memcpy(skb_put(skb, HCI_EVENT_HDR_SIZE), buf,
> > > + HCI_EVENT_HDR_SIZE);
> > > + plen = hci_event_hdr(skb)->plen;
> > > + buf += HCI_EVENT_HDR_SIZE;
> > > + break;
> > > + default:
> > > + ret = -EILSEQ;
> > > + kfree_skb(skb);
> > > + goto exit_error;
> > > + }
> > > + memcpy(skb_put(skb, plen), buf, plen);
> > > +
> > > + if (pkt_type == BTINTEL_PCIE_HCI_EVT_PKT)
> > > + ret = btintel_pcie_recv_event_intel(hdev, skb);
> > > + else
> > > + ret = hci_recv_frame(hdev, skb);
> > > +
> > > +exit_error:
> > > + if (ret)
> > > + hdev->stat.err_rx++;
> > > +
> > > + spin_unlock(&data->hci_rx_lock);
> > > +
> > > + return ret;
> > > +}
> > > +
> > > +/* RX work queue */
> > > +static void btintel_pcie_rx_work(struct work_struct *work)
> > > +{
> > > + struct btintel_pcie_data *data = container_of(work,
> > > + struct btintel_pcie_data, rx_work);
> > > + struct sk_buff *skb;
> > > + int err;
> > > +
> > > + /* Process the sk_buf in queue and send to the hci layer */
> > > + while ((skb = skb_dequeue(&data->rx_skb_q))) {
> > > + err = btintel_pcie_hci_recv_frame(data, skb->data, skb->len);
> > > + if (err) {
> > > + BT_ERR("Failed to send received frame: %d", err);
> > > + kfree_skb(skb);
> > > + }
> > > + }
> > > +}
> > > +
> > > +/* create the sk_buff with data and save it to queue and start rx work
> > > + */
> > > +static int btintel_pcie_submit_rx_work(struct btintel_pcie_data *data, u8
> > status,
> > > + void *buf)
> > > +{
> > > + int ret, len;
> > > + struct rfh_hdr *rfh_hdr;
> > > + struct sk_buff *skb;
> > > +
> > > + rfh_hdr = (struct rfh_hdr *)buf;
> > > + btintel_pcie_hci_dump("RFH HDR", buf, sizeof(*rfh_hdr));
> > > +
> > > + len = rfh_hdr->packet_len;
> > > +
> > > + /* Remove RFH header */
> > > + buf += sizeof(*rfh_hdr);
> > > + btintel_pcie_hci_dump("RX", buf, len);
> > > +
> > > + /* Create the sk_buf with packet in the buf and save it to sk_buf
> > queue
> > > + */
> > > + skb = alloc_skb(len, GFP_ATOMIC);
> > > + if (!skb) {
> > > + ret = -ENOMEM;
> > > + goto resubmit;
> > > + }
> > > +
> > > + /* Copy the data to skb */
> > > + memcpy(skb_put(skb, len), buf, len);
> > > +
> > > + /* Save the skb to rx queue */
> > > + skb_queue_tail(&data->rx_skb_q, skb);
> > > +
> > > + /* Calling rx_work queue to process the skb */
> > > + queue_work(data->workqueue, &data->rx_work);
> > > +
> > > +resubmit:
> > > + BT_DBG("submit next read request");
> > > +
> > > + /* submit read */
> > > + ret = btintel_pcie_submit_rx(data);
> > > +
> > > + return ret;
> > > +}
> > > +
> > > +/* This function handles the MSI-X interrupt for rx queue 1 which is for RX
> > > + */
> > > +static void btintel_pcie_msix_rx_handle(struct btintel_pcie_data *data)
> > > +{
> > > + u16 cr_hia, cr_tia;
> > > + struct rxq *rxq;
> > > + struct urbd1 *urbd1;
> > > + struct frbd *frbd;
> > > + struct data_buf *buf;
> > > + int ret;
> > > +
> > > + cr_hia = data->ia.cr_hia[RXQ_NUM];
> > > + cr_tia = data->ia.cr_tia[RXQ_NUM];
> > > +
> > > + BT_DBG("[RXQ] cr_hia=%u cr_tia=%u", cr_hia, cr_tia);
> > > +
> > > + /* Check CR_TIA and CR_HIA for change */
> > > + if (cr_tia == cr_hia) {
> > > + BT_ERR("[RXQ] no new CD found");
> > > + return;
> > > + }
> > > +
> > > + rxq = &data->rxq;
> > > +
> > > + /* The firmware sends multiple CD in a single MSIX and it needs to
> > > + * process all received CDs in this interrupt.
> > > + */
> > > + while (cr_tia != cr_hia) {
> > > + /* Get URBD1 pointed by cr_tia */
> > > + urbd1 = &rxq->urbd1s[cr_tia];
> > > + ipc_print_urbd1(urbd1, cr_tia);
> > > +
> > > + /* Get FRBD poined by urbd1->frbd_tag */
> > > + frbd = &rxq->frbds[urbd1->frbd_tag];
> > > +
> > > + /* Get buf from FRBD tag */
> > > + buf = &rxq->bufs[urbd1->frbd_tag];
> > > + if (!buf) {
> > > + BT_ERR("[RXQ] failed to get the DMA buffer for %d",
> > > + urbd1->frbd_tag);
> > > + return;
> > > + }
> > > +
> > > + /* prepare RX work */
> > > + ret = btintel_pcie_submit_rx_work(data, urbd1->status,
> > > + buf->data);
> > > + if (ret) {
> > > + BT_ERR("[RXQ] failed to submit rx request");
> > > + return;
> > > + }
> > > +
> > > + /* Update cr_tia */
> > > + cr_tia = (cr_tia + 1) % rxq->count;
> > > + data->ia.cr_tia[RXQ_NUM] = cr_tia;
> > > + ipc_print_ia_ring(&data->ia, RXQ_NUM);
> > > + }
> > > + BT_DBG("[RXQ] completed rx interrupt");
> > > +}
> > > +
> > > +static irqreturn_t btintel_pcie_msix_isr(int irq, void *data)
> > > +{
> > > + return IRQ_WAKE_THREAD;
> > > +}
> > > +
> > > +static irqreturn_t btintel_pcie_irq_msix_handler(int irq, void *dev_id)
> > > +{
> > > + struct msix_entry *entry = dev_id;
> > > + struct btintel_pcie_data *data = btintel_pcie_get_data(entry);
> > > + u32 intr_fh, intr_hw;
> > > +
> > > + BT_DBG("handling msix(irq=%d dev_id=0x%p)", irq, dev_id);
> > > +
> > > + spin_lock(&data->irq_lock);
> > > + intr_fh = btintel_pcie_rd_reg32(data, CSR_MSIX_FH_INT_CAUSES);
> > > + intr_hw = btintel_pcie_rd_reg32(data, CSR_MSIX_HW_INT_CAUSES);
> > > +
> > > + /* Clear causes registers to avoid being handling the same cause */
> > > + btintel_pcie_wr_reg32(data, CSR_MSIX_FH_INT_CAUSES, intr_fh);
> > > + btintel_pcie_wr_reg32(data, CSR_MSIX_HW_INT_CAUSES, intr_hw);
> > > + spin_unlock(&data->irq_lock);
> > > +
> > > + BT_DBG("intr_fh=0x%x intr_hw=0x%x", intr_fh, intr_hw);
> > > +
> > > + if (unlikely(!(intr_fh | intr_hw))) {
> > > + BT_DBG("Ignore interrupt, inta == 0");
> > > + return IRQ_NONE;
> > > + }
> > > +
> > > + /* This interrupt is triggered by the firmware after updating
> > > + * boot_stage register and image_response register
> > > + */
> > > + if (intr_hw & MSIX_HW_INT_CAUSES_GP0) {
> > > + BT_DBG("intr for MSIX_HW_INT_CAUSES_GP0");
> > > + btintel_pcie_msix_gp0_handler(data);
> > > + }
> > > +
> > > + /* For TX */
> > > + if (intr_fh & MSIX_FH_INT_CAUSES_0) {
> > > + BT_DBG("intr for MSIX_FH_INT_CAUSES_0");
> > > + btintel_pcie_msix_tx_handle(data);
> > > + }
> > > +
> > > + /* For RX */
> > > + if (intr_fh & MSIX_FH_INT_CAUSES_1) {
> > > + BT_DBG("intr for MSIX_FH_INT_CAUSES_1");
> > > + btintel_pcie_msix_rx_handle(data);
> > > + }
> > > +
> > > + /* TODO: Add handler for other causes */
> > > + /*
> > > + * Before sending the interrupt the HW disables it to prevent
> > > + * a nested interrupt. This is done by writing 1 to the corresponding
> > > + * bit in the mask register. After handling the interrupt, it should be
> > > + * re-enabled by clearing this bit. This register is defined as
> > > + * write 1 clear (W1C) register, meaning that it's being clear
> > > + * by writing 1 to the bit.
> > > + */
> > > + btintel_pcie_wr_reg32(data, CSR_MSIX_AUTOMASK_ST, BIT(entry-
> > >entry));
> > > +
> > > + return IRQ_HANDLED;
> > > +}
> > > +
> > > +/* This function requests the irq for msix and registers the handlers per irq.
> > > + * Currently, it requests only 1 irq for all interrupt causes.
> > > + */
> > > +static int btintel_pcie_setup_irq(struct btintel_pcie_data *data)
> > > +{
> > > + int err;
> > > + int num_irqs, i;
> > > +
> > > + BT_DBG("Initialize msix_entries...");
> > > + for (i = 0; i < MSIX_VEC_MAX; i++) {
> > > + data->msix_entries[i].entry = i;
> > > + BT_DBG("msix_entries[%d] vector=0x%x entry=0x%x",
> > > + i, data->msix_entries[i].vector,
> > > + data->msix_entries[i].entry);
> > > + }
> > > +
> > > + num_irqs = pci_enable_msix_range(data->pdev, data->msix_entries,
> > > + MSIX_VEC_MIN,
> > > + MSIX_VEC_MAX);
> > > + if (num_irqs < 0) {
> > > + BT_ERR("Failed to enable msix range (%d)", num_irqs);
> > > + return num_irqs;
> > > + }
> > > +
> > > + data->alloc_vecs = num_irqs;
> > > + data->msix_enabled = 1;
> > > + data->def_irq = 0;
> > > +
> > > + BT_DBG("Returned num_irqs=%d", num_irqs);
> > > + for (i = 0; i < num_irqs; i++) {
> > > + BT_DBG("msix_entries[%d] vector=0x%x entry=0x%x", i,
> > > + data->msix_entries[i].vector,
> > > + data->msix_entries[i].entry);
> > > + }
> > > +
> > > + BT_DBG("setup irq handler");
> > > + for (i = 0; i < data->alloc_vecs; i++) {
> > > + struct msix_entry *msix_entry;
> > > +
> > > + msix_entry = &data->msix_entries[i];
> > > +
> > > + err = devm_request_threaded_irq(&data->pdev->dev,
> > > + msix_entry->vector,
> > > + btintel_pcie_msix_isr,
> > > +
> > btintel_pcie_irq_msix_handler,
> > > + IRQF_SHARED,
> > > + KBUILD_MODNAME,
> > > + msix_entry);
> > > + if (err) {
> > > + BT_ERR("Failed to allocate irq handler (%d)", err);
> > > + return err;
> > > + }
> > > + }
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +struct btintel_pcie_causes_list {
> > > + u32 cause;
> > > + u32 mask_reg;
> > > + u8 cause_num;
> > > +};
> > > +
> > > +struct btintel_pcie_causes_list causes_list[] = {
> > > + { MSIX_FH_INT_CAUSES_0, CSR_MSIX_FH_INT_MASK,
> > 0x00 },
> > > + { MSIX_FH_INT_CAUSES_1, CSR_MSIX_FH_INT_MASK,
> > 0x01 },
> > > + { MSIX_HW_INT_CAUSES_GP0, CSR_MSIX_HW_INT_MASK, 0x20
> > },
> > > +};
> > > +
> > > +/* This function configures the interrupt masks for both HW_INT_CAUSES
> > and
> > > + * FH_INT_CAUSES which are meaningful to us.
> > > + *
> > > + * After resetting BT function via PCIE FLR or FUNC_CTRL reset, the driver
> > > + * need to call this function again to configure it again since the masks
> > > + * are reset to 0xFFFFFFFF after reset.
> > > + */
> > > +static void btintel_pcie_config_msix(struct btintel_pcie_data *data)
> > > +{
> > > + int i;
> > > + int val = data->def_irq | MSIX_NON_AUTO_CLEAR_CAUSE;
> > > +
> > > + /* Set Non Auto Clear Cause */
> > > + for (i = 0; i < ARRAY_SIZE(causes_list); i++) {
> > > + btintel_pcie_wr_reg8(data,
> > > + CSR_MSIX_IVAR(causes_list[i].cause_num),
> > > + val);
> > > + btintel_pcie_clr_reg_bits(data,
> > > + causes_list[i].mask_reg,
> > > + causes_list[i].cause);
> > > + }
> > > +
> > > + /* Save the initial interrupt mask */
> > > + data->fh_init_mask = ~btintel_pcie_rd_reg32(data,
> > CSR_MSIX_FH_INT_MASK);
> > > + data->hw_init_mask = ~btintel_pcie_rd_reg32(data,
> > CSR_MSIX_HW_INT_MASK);
> > > + BT_DBG("init_mask: fh=0x%x hw=0x%x", data->fh_init_mask,
> > > + data->hw_init_mask);
> > > +}
> > > +
> > > +static int btintel_pcie_config_pcie(struct pci_dev *pdev,
> > > + struct btintel_pcie_data *data)
> > > +{
> > > + int err;
> > > +
> > > + err = pcim_enable_device(pdev);
> > > + if (err) {
> > > + BT_ERR("Failed to enable pci device (%d)", err);
> > > + return err;
> > > + }
> > > + pci_set_master(pdev);
> > > +
> > > + /* Setup DMA mask */
> > > + BT_DBG("Set DMA_MASK(64)");
> > > + err = dma_set_mask_and_coherent(&pdev->dev,
> > DMA_BIT_MASK(64));
> > > + if (err) {
> > > + BT_DBG("Set DMA_MASK(32)");
> > > + err = dma_set_mask_and_coherent(&pdev->dev,
> > DMA_BIT_MASK(32));
> > > + /* Both attempt failed */
> > > + if (err) {
> > > + BT_ERR("No suitable DMA available");
> > > + return err;
> > > + }
> > > + }
> > > +
> > > + /* Get BAR to access CSR */
> > > + err = pcim_iomap_regions(pdev, BIT(0), KBUILD_MODNAME);
> > > + if (err) {
> > > + BT_ERR("Failed to get iomap regions (%d)", err);
> > > + return err;
> > > + }
> > > +
> > > + data->base_addr = pcim_iomap_table(pdev)[0];
> > > + if (!data->base_addr) {
> > > + BT_ERR("Failed to get base address");
> > > + return -ENODEV;
> > > + }
> > > +
> > > + err = btintel_pcie_setup_irq(data);
> > > + if (err) {
> > > + BT_ERR("Failed to setup irq for msix");
> > > + return err;
> > > + }
> > > +
> > > + /* Configure MSI-X with causes list */
> > > + btintel_pcie_config_msix(data);
> > > +
> > > + return 0;
> > > +}
> > > +
> > > +static void btintel_pcie_init_ci(struct btintel_pcie_data *data,
> > > + struct ctx_info *ci)
> > > +{
> > > + ci->version = 0x1;
> > > + ci->size = sizeof(*ci);
> > > + ci->config = 0x0000;
> > > + ci->addr_cr_hia = data->ia.cr_hia_p_addr;
> > > + ci->addr_tr_tia = data->ia.tr_tia_p_addr;
> > > + ci->addr_cr_tia = data->ia.cr_tia_p_addr;
> > > + ci->addr_tr_hia = data->ia.tr_hia_p_addr;
> > > + ci->num_cr_ia = NUM_QUEUES;
> > > + ci->num_tr_ia = NUM_QUEUES;
> > > + ci->addr_urbdq0 = data->txq.urbd0s_p_addr;
> > > + ci->addr_tfdq = data->txq.tfds_p_addr;
> > > + ci->num_tfdq = data->txq.count;
> > > + ci->num_urbdq0 = data->txq.count;
> > > + ci->tfdq_db_vec = TXQ_NUM;
> > > + ci->urbdq0_db_vec = TXQ_NUM;
> > > + ci->rbd_size = RBD_SIZE_4K;
> > > + ci->addr_frbdq = data->rxq.frbds_p_addr;
> > > + ci->num_frbdq = data->rxq.count;
> > > + ci->frbdq_db_vec = RXQ_NUM;
> > > + ci->addr_urbdq1 = data->rxq.urbd1s_p_addr;
> > > + ci->num_urbdq1 = data->rxq.count;
> > > + ci->urbdq_db_vec = RXQ_NUM;
> > > +}
> > > +
> > > +static void btintel_pcie_free_txq_bufs(struct btintel_pcie_data *data,
> > > + struct txq *txq)
> > > +{
> > > + /* Free data buffers first */
> > > + dma_free_coherent(&data->pdev->dev, txq->count * BUFFER_SIZE,
> > > + txq->buf_v_addr, txq->buf_p_addr);
> > > + kfree(txq->bufs);
> > > + BT_DBG("txq buffers are freed");
> > > +}
> > > +
> > > +static int btintel_pcie_setup_txq_bufs(struct btintel_pcie_data *data,
> > > + struct txq *txq)
> > > +{
> > > + int err = 0, i;
> > > + struct data_buf *buf;
> > > +
> > > + if (txq->count == 0) {
> > > + BT_ERR("invalid parameter: txq->count");
> > > + err = -EINVAL;
> > > + goto exit_error;
> > > + }
> > > +
> > > + /* Allocate the same number of buffers as the descriptor */
> > > + txq->bufs = kmalloc_array(txq->count, sizeof(*buf), GFP_KERNEL);
> > > + if (!txq->bufs) {
> > > + err = -ENOMEM;
> > > + goto exit_error;
> > > + }
> > > +
> > > + /* Allocate full chunk of data buffer for DMA first and do indexing and
> > > + * initialization next, so it can be freed easily
> > > + */
> > > + txq->buf_v_addr = dma_alloc_coherent(&data->pdev->dev,
> > > + txq->count * BUFFER_SIZE,
> > > + &txq->buf_p_addr,
> > > + GFP_KERNEL | __GFP_NOWARN);
> > > + if (!txq->buf_v_addr) {
> > > + BT_ERR("Failed to allocate DMA buf");
> > > + err = -ENOMEM;
> > > + kfree(txq->bufs);
> > > + goto exit_error;
> > > + }
> > > + memset(txq->buf_v_addr, 0, txq->count * BUFFER_SIZE);
> > > +
> > > + BT_DBG("alloc bufs: p=0x%llx v=0x%p", txq->buf_p_addr, txq-
> > >buf_v_addr);
> > > +
> > > + /* Setup the allocated DMA buffer to bufs. Each data_buf should
> > > + * have virtual address and physical address
> > > + */
> > > + for (i = 0; i < txq->count; i++) {
> > > + buf = &txq->bufs[i];
> > > + buf->data_p_addr = txq->buf_p_addr + (i * BUFFER_SIZE);
> > > + buf->data = txq->buf_v_addr + (i * BUFFER_SIZE);
> > > + }
> > > +
> > > +exit_error:
> > > + return err;
> > > +}
> > > +
> > > +static void btintel_pcie_free_rxq_bufs(struct btintel_pcie_data *data,
> > > + struct rxq *rxq)
> > > +{
> > > + /* Free data buffers first */
> > > + dma_free_coherent(&data->pdev->dev, rxq->count * BUFFER_SIZE,
> > > + rxq->buf_v_addr, rxq->buf_p_addr);
> > > + kfree(rxq->bufs);
> > > + BT_DBG("rxq buffers are freed");
> > > +}
> > > +
> > > +static int btintel_pcie_setup_rxq_bufs(struct btintel_pcie_data *data,
> > > + struct rxq *rxq)
> > > +{
> > > + int err = 0, i;
> > > + struct data_buf *buf;
> > > +
> > > + if (rxq->count == 0) {
> > > + BT_ERR("invalid parameter: rxq->count");
> > > + err = -EINVAL;
> > > + goto exit_error;
> > > + }
> > > +
> > > + /* Allocate the same number of buffers as the descriptor */
> > > + rxq->bufs = kmalloc_array(rxq->count, sizeof(*buf), GFP_KERNEL);
> > > + if (!rxq->bufs) {
> > > + err = -ENOMEM;
> > > + goto exit_error;
> > > + }
> > > +
> > > + /* Allocate full chunk of data buffer for DMA first and do indexing and
> > > + * initialization next, so it can be freed easily
> > > + */
> > > + rxq->buf_v_addr = dma_alloc_coherent(&data->pdev->dev,
> > > + rxq->count * BUFFER_SIZE,
> > > + &rxq->buf_p_addr,
> > > + GFP_KERNEL | __GFP_NOWARN);
> > > + if (!rxq->buf_v_addr) {
> > > + BT_ERR("Failed to allocate DMA buf");
> > > + err = -ENOMEM;
> > > + kfree(rxq->bufs);
> > > + goto exit_error;
> > > + }
> > > + memset(rxq->buf_v_addr, 0, rxq->count * BUFFER_SIZE);
> > > +
> > > + BT_DBG("alloc bufs: p=0x%llx v=0x%p", rxq->buf_p_addr, rxq-
> > >buf_v_addr);
> > > +
> > > + /* Setup the allocated DMA buffer to bufs. Each data_buf should
> > > + * have virtual address and physical address
> > > + */
> > > + for (i = 0; i < rxq->count; i++) {
> > > + buf = &rxq->bufs[i];
> > > + buf->data_p_addr = rxq->buf_p_addr + (i * BUFFER_SIZE);
> > > + buf->data = rxq->buf_v_addr + (i * BUFFER_SIZE);
> > > + }
> > > +
> > > +exit_error:
> > > +
> > > + return err;
> > > +}
> > > +
> > > +static void btintel_pcie_setup_ia(struct btintel_pcie_data *data,
> > > + dma_addr_t p_addr, void *v_addr,
> > > + struct ia *ia)
> > > +{
> > > + /* TR Head Index Array */
> > > + ia->tr_hia_p_addr = p_addr;
> > > + ia->tr_hia = v_addr;
> > > +
> > > + /* TR Tail Index Array */
> > > + ia->tr_tia_p_addr = p_addr + sizeof(u16) * NUM_QUEUES;
> > > + ia->tr_tia = v_addr + sizeof(u16) * NUM_QUEUES;
> > > +
> > > + /* CR Head index Array */
> > > + ia->cr_hia_p_addr = p_addr + (sizeof(u16) * NUM_QUEUES * 2);
> > > + ia->cr_hia = v_addr + (sizeof(u16) * NUM_QUEUES * 2);
> > > +
> > > + /* CR Tail Index Array */
> > > + ia->cr_tia_p_addr = p_addr + (sizeof(u16) * NUM_QUEUES * 3);
> > > + ia->cr_tia = v_addr + (sizeof(u16) * NUM_QUEUES * 3);
> > > +}
> > > +
> > > +static void btintel_pcie_free(struct btintel_pcie_data *data)
> > > +{
> > > + btintel_pcie_free_rxq_bufs(data, &data->rxq);
> > > + btintel_pcie_free_txq_bufs(data, &data->txq);
> > > +
> > > + dma_pool_free(data->dma_pool, data->dma_v_addr, data-
> > >dma_p_addr);
> > > + dma_pool_destroy(data->dma_pool);
> > > + BT_DBG("DMA memory is freed");
> > > +}
> > > +
> > > +/* Allocate tx and rx queues, any related data structures and buffers.
> > > + */
> > > +static int btintel_pcie_alloc(struct btintel_pcie_data *data)
> > > +{
> > > + int err = 0;
> > > + size_t total;
> > > + dma_addr_t p_addr;
> > > + void *v_addr;
> > > +
> > > + /* Allocate the chunk of DMA memory for descriptors, index array,
> > and
> > > + * context information, instead of allocating individually.
> > > + * The DMA memory for data buffer is allocated while setting up the
> > > + * each queue.
> > > + *
> > > + * Total size is sum of the following
> > > + * + size of TFD * Number of descriptors in queue
> > > + * + size of URBD0 * Number of descriptors in queue
> > > + * + size of FRBD * Number of descriptors in queue
> > > + * + size of URBD1 * Number of descriptors in queue
> > > + * + size of index * Number of queues(2) * type of index array(4)
> > > + * + size of context information
> > > + */
> > > + total = (sizeof(struct tfd) + sizeof(struct urbd0) + sizeof(struct frbd)
> > > + + sizeof(struct urbd1)) * DESCS_COUNT;
> > > +
> > > + /* Add the sum of size of index array and size of ci struct */
> > > + total += (sizeof(u16) * NUM_QUEUES * 4) + sizeof(struct ctx_info);
> > > +
> > > + /* Allocate DMA Pool */
> > > + data->dma_pool = dma_pool_create(KBUILD_MODNAME, &data-
> > >pdev->dev,
> > > + total, DMA_POOL_ALIGNMENT, 0);
> > > + if (!data->dma_pool) {
> > > + BT_ERR("Failed to allocate dma pool for queues");
> > > + err = -ENOMEM;
> > > + goto exit_error;
> > > + }
> > > +
> > > + v_addr = dma_pool_zalloc(data->dma_pool, GFP_KERNEL |
> > __GFP_NOWARN,
> > > + &p_addr);
> > > + if (!v_addr) {
> > > + BT_ERR("Failed to alloc dma memory for queues");
> > > + dma_pool_destroy(data->dma_pool);
> > > + err = -ENOMEM;
> > > + goto exit_error;
> > > + }
> > > +
> > > + data->dma_p_addr = p_addr;
> > > + data->dma_v_addr = v_addr;
> > > +
> > > + BT_DBG("dma pool: p_addr=0x%llx v_addr=0x%p", p_addr, v_addr);
> > > +
> > > + /* Setup descriptor count */
> > > + data->txq.count = DESCS_COUNT;
> > > + data->rxq.count = DESCS_COUNT;
> > > +
> > > + /* Setup tfds */
> > > + data->txq.tfds_p_addr = p_addr;
> > > + data->txq.tfds = v_addr;
> > > +
> > > + p_addr += (sizeof(struct tfd) * DESCS_COUNT);
> > > + v_addr += (sizeof(struct tfd) * DESCS_COUNT);
> > > +
> > > + /* Setup urbd0 */
> > > + data->txq.urbd0s_p_addr = p_addr;
> > > + data->txq.urbd0s = v_addr;
> > > +
> > > + p_addr += (sizeof(struct urbd0) * DESCS_COUNT);
> > > + v_addr += (sizeof(struct urbd0) * DESCS_COUNT);
> > > +
> > > + /* Setup frbd */
> > > + data->rxq.frbds_p_addr = p_addr;
> > > + data->rxq.frbds = v_addr;
> > > +
> > > + p_addr += (sizeof(struct frbd) * DESCS_COUNT);
> > > + v_addr += (sizeof(struct frbd) * DESCS_COUNT);
> > > +
> > > + /* Setup urbd1 */
> > > + data->rxq.urbd1s_p_addr = p_addr;
> > > + data->rxq.urbd1s = v_addr;
> > > +
> > > + p_addr += (sizeof(struct urbd1) * DESCS_COUNT);
> > > + v_addr += (sizeof(struct urbd1) * DESCS_COUNT);
> > > +
> > > + /* Setup data buffers for txq */
> > > + err = btintel_pcie_setup_txq_bufs(data, &data->txq);
> > > + if (err) {
> > > + BT_ERR("Failed to setup txq buffers: %d", err);
> > > + goto exit_error_pool;
> > > + }
> > > +
> > > + /* Setup data buffers for rxq */
> > > + err = btintel_pcie_setup_rxq_bufs(data, &data->rxq);
> > > + if (err) {
> > > + BT_ERR("Failed to allocate rxq buffers: %d", err);
> > > + goto exit_error_txq;
> > > + }
> > > +
> > > + /* Setup Index Array */
> > > + btintel_pcie_setup_ia(data, p_addr, v_addr, &data->ia);
> > > +
> > > + /* Setup Context Information */
> > > + p_addr += sizeof(u16) * NUM_QUEUES * 4;
> > > + v_addr += sizeof(u16) * NUM_QUEUES * 4;
> > > +
> > > + data->ci = v_addr;
> > > + data->ci_p_addr = p_addr;
> > > +
> > > + /* Initialize the CI */
> > > + btintel_pcie_init_ci(data, data->ci);
> > > +
> > > + return 0;
> > > +
> > > +exit_error_txq:
> > > + btintel_pcie_free_txq_bufs(data, &data->txq);
> > > +exit_error_pool:
> > > + dma_pool_free(data->dma_pool, data->dma_v_addr, data-
> > >dma_p_addr);
> > > + dma_pool_destroy(data->dma_pool);
> > > +exit_error:
> > > + return err;
> > > +}
> > > +
> > > +static void btintel_pcie_release_hdev(struct btintel_pcie_data *data)
> > > +{
> > > + struct hci_dev *hdev;
> > > +
> > > + hdev = data->hdev;
> > > + if (hdev) {
> > > + hci_unregister_dev(hdev);
> > > + hci_free_dev(hdev);
> > > + }
> > > + data->hdev = NULL;
> > > +}
> > > +
> > > +static int btintel_pcie_setup_hdev(struct btintel_pcie_data *data)
> > > +{
> > > + /* TODO: initialize hdev and assign the callbacks to hdev */
> > > + return -ENODEV;
> > > +}
> > > +
> > > +static int btintel_pcie_probe(struct pci_dev *pdev,
> > > + const struct pci_device_id *ent)
> > > +{
> > > + int err;
> > > + struct btintel_pcie_data *data;
> > > +
> > > + if (!pdev)
> > > + return -ENODEV;
> > > +
> > > + data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
> > > + if (!data)
> > > + return -ENOMEM;
> > > +
> > > + /* initialize the btintel_pcie data struct */
> > > + data->pdev = pdev;
> > > +
> > > + spin_lock_init(&data->irq_lock);
> > > + spin_lock_init(&data->hci_rx_lock);
> > > +
> > > + init_waitqueue_head(&data->gp0_wait_q);
> > > + data->gp0_received = false;
> > > +
> > > + init_waitqueue_head(&data->tx_wait_q);
> > > + data->tx_wait_done = false;
> > > +
> > > + data->workqueue = alloc_ordered_workqueue(KBUILD_MODNAME,
> > WQ_HIGHPRI);
> > > + if (!data->workqueue) {
> > > + BT_ERR("Failed to create workqueue");
> > > + return -ENOMEM;
> > > + }
> > > + skb_queue_head_init(&data->rx_skb_q);
> > > + INIT_WORK(&data->rx_work, btintel_pcie_rx_work);
> > > +
> > > + data->boot_stage_cache = 0x00;
> > > + data->img_resp_cache = 0x00;
> > > +
> > > + /* PCIe specific all to configure it for this device includes
> > > + * enabling pice device, setting master, reading BAR[0], configuring
> > > + * MSIx, setting DMA mask, and save the driver data.
> > > + */
> > > + err = btintel_pcie_config_pcie(pdev, data);
> > > + if (err) {
> > > + BT_ERR("Failed to config pcie (%d)", err);
> > > + goto exit_error;
> > > + }
> > > +
> > > + /* Set driver data for this PCI device */
> > > + pci_set_drvdata(pdev, data);
> > > +
> > > + /* allocate the IPC struct */
> > > + err = btintel_pcie_alloc(data);
> > > + if (err) {
> > > + BT_ERR("Failed to allocate queues(%d)", err);
> > > + goto exit_error;
> > > + }
> > > +
> > > + /* Enable BT function */
> > > + err = btintel_pcie_enable_bt(data);
> > > + if (err) {
> > > + BT_ERR("Failed to start bluetooth device(%d)", err);
> > > + goto exit_error;
> > > + }
> > > +
> > > + /* CNV information (CNVi and CNVr) is in CSR */
> > > + data->cnvi = btintel_pcie_rd_reg32(data, CSR_HW_REV_REG);
> > > + BT_DBG("cnvi: 0x%08x", data->cnvi);
> > > +
> > > + data->cnvr = btintel_pcie_rd_reg32(data, CSR_RF_ID_REG);
> > > + BT_DBG("cnvr: 0x%08x", data->cnvr);
> > > +
> > > + err = btintel_pcie_start_rx(data);
> > > + if (err) {
> > > + BT_ERR("Failed to start rx (%d)", err);
> > > + goto exit_error;
> > > + }
> > > +
> > > + err = btintel_pcie_setup_hdev(data);
> > > + if (err) {
> > > + BT_ERR("Failed to setup HCI module");
> > > + goto exit_error;
> > > + }
> > > +
> > > + return 0;
> > > +
> > > +exit_error:
> > > + /* reset device before leave */
> > > + btintel_pcie_reset_bt(data);
> > > +
> > > + /* clear bus mastering */
> > > + pci_clear_master(pdev);
> > > +
> > > + /* Unset driver data for PCI device */
> > > + pci_set_drvdata(pdev, NULL);
> > > +
> > > + return err;
> > > +}
> > > +
> > > +static void btintel_pcie_remove(struct pci_dev *pdev)
> > > +{
> > > + struct btintel_pcie_data *data;
> > > +
> > > + if (!pdev) {
> > > + BT_ERR("Invalid parameter: pdev");
> > > + return;
> > > + }
> > > +
> > > + data = pci_get_drvdata(pdev);
> > > + if (!data) {
> > > + BT_ERR("data is empty");
> > > + return;
> > > + }
> > > +
> > > + btintel_pcie_release_hdev(data);
> > > +
> > > + flush_work(&data->rx_work);
> > > +
> > > + destroy_workqueue(data->workqueue);
> > > +
> > > + btintel_pcie_free(data);
> > > +
> > > + /* reset device before leave */
> > > + btintel_pcie_reset_bt(data);
> > > +
> > > + /* clear bus mastering */
> > > + pci_clear_master(pdev);
> > > +
> > > + /* Unset driver data for PCI device */
> > > + pci_set_drvdata(pdev, NULL);
> > > +}
> > > +
> > > +#ifdef CONFIG_PM
> > > +static int btintel_pcie_suspend(struct device *dev)
> > > +{
> > > + /* TODO: Add support suspend */
> > > + return 0;
> > > +}
> > > +
> > > +static int btintel_pcie_resume(struct device *dev)
> > > +{
> > > + /* TODO: Add support resume */
> > > + return 0;
> > > +}
> > > +
> > > +static SIMPLE_DEV_PM_OPS(btintel_pcie_pm_ops, btintel_pcie_suspend,
> > > + btintel_pcie_resume);
> > > +#endif /* CONFIG_PM */
> > > +
> > > +static struct pci_driver btintel_pcie_driver = {
> > > + .name = KBUILD_MODNAME,
> > > + .id_table = btintel_pcie_table,
> > > + .probe = btintel_pcie_probe,
> > > + .remove = btintel_pcie_remove,
> > > +#ifdef CONFIG_PM
> > > + .driver.pm = &btintel_pcie_pm_ops,
> > > +#endif /* CONFIG_PM */
> > > +};
> > > +module_pci_driver(btintel_pcie_driver);
> > > +
> > > +MODULE_AUTHOR("Tedd Ho-Jeong An <tedd.an@intel.com>");
> > > +MODULE_DESCRIPTION("Intel Bluetooth PCIe transport driver ver "
> > VERSION);
> > > +MODULE_VERSION(VERSION);
> > > +MODULE_LICENSE("GPL");
> > > diff --git a/drivers/bluetooth/btintel_pcie.h
> > b/drivers/bluetooth/btintel_pcie.h
> > > new file mode 100644
> > > index 000000000000..1554964686bd
> > > --- /dev/null
> > > +++ b/drivers/bluetooth/btintel_pcie.h
> > > @@ -0,0 +1,449 @@
> > > +/* SPDX-License-Identifier: GPL-2.0-or-later */
> > > +/*
> > > + * Intel Bluetooth PCIE driver
> > > + *
> > > + * Copyright (C) 2017 Intel Corporation. All rights reserved.
> > > + *
> > > + * This program is free software; you can redistribute it and/or
> > > + * modify it under the terms of the GNU General Public License version
> > > + * 2 as published by the Free Software Foundation.
> > > + *
> > > + * This program is distributed in the hope that it will be useful,
> > > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> > > + * GNU General Public License for more details.
> > > + *
> > > + * Copyright (C) 2022 Intel Corporation
> >
> > Ditto.
> Ack.
>
> >
> > > + *
> > > + * Intel Bluetooth Driver for PCIE interface.
> > > + */
> > > +
> > > +/* Control and Status Register(CSR) */
> > > +#define CSR_BASE (0x000)
> > > +#define CSR_FUNC_CTRL_REG (CSR_BASE + 0x024)
> > > +#define CSR_HW_REV_REG (CSR_BASE + 0x028)
> > > +#define CSR_RF_ID_REG (CSR_BASE + 0x09C)
> > > +#define CSR_BOOT_STAGE_REG (CSR_BASE + 0x108)
> > > +#define CSR_CI_ADDR_LSB_REG (CSR_BASE + 0x118)
> > > +#define CSR_CI_ADDR_MSB_REG (CSR_BASE + 0x11C)
> > > +#define CSR_IMG_RESPONSE_REG (CSR_BASE + 0x12C)
> > > +#define CSR_HBUS_TARG_WRPTR (CSR_BASE + 0x460)
> > > +
> > > +/* CSR Function Control Register */
> > > +#define CSR_FUNC_CTRL_FUNC_ENA (BIT(0))
> > > +#define CSR_FUNC_CTRL_MAC_INIT (BIT(6))
> > > +#define CSR_FUNC_CTRL_FUNC_INIT (BIT(7))
> > > +#define CSR_FUNC_CTRL_MAC_ACCESS_STS (BIT(20))
> > > +#define CSR_FUNC_CTRL_SW_RESET (BIT(31))
> > > +
> > > +/* Value for CSR_BOOT_STAGE register */
> > > +#define CSR_BOOT_STAGE_ROM (BIT(0))
> > > +#define CSR_BOOT_STAGE_IML (BIT(1))
> > > +#define CSR_BOOT_STAGE_OPFW (BIT(2))
> > > +#define CSR_BOOT_STAGE_ROM_LOCKDOWN (BIT(10))
> > > +#define CSR_BOOT_STAGE_IML_LOCKDOWN (BIT(11))
> > > +#define CSR_BOOT_STAGE_MAC_ACCESS_ON (BIT(16))
> > > +#define CSR_BOOT_STAGE_ALIVE (BIT(23))
> > > +
> > > +/* Registers for MSIX */
> > > +#define CSR_MSIX_BASE (0x2000)
> > > +#define CSR_MSIX_FH_INT_CAUSES (CSR_MSIX_BASE + 0x0800)
> > > +#define CSR_MSIX_FH_INT_MASK (CSR_MSIX_BASE + 0x0804)
> > > +#define CSR_MSIX_HW_INT_CAUSES (CSR_MSIX_BASE +
> > 0x0808)
> > > +#define CSR_MSIX_HW_INT_MASK (CSR_MSIX_BASE + 0x080C)
> > > +#define CSR_MSIX_AUTOMASK_ST (CSR_MSIX_BASE + 0x0810)
> > > +#define CSR_MSIX_AUTOMASK_EN (CSR_MSIX_BASE + 0x0814)
> > > +#define CSR_MSIX_IVAR_BASE (CSR_MSIX_BASE + 0x0880)
> > > +#define CSR_MSIX_IVAR(cause) (CSR_MSIX_IVAR_BASE +
> > (cause))
> > > +
> > > +/* Causes for the FH register interrupts */
> > > +enum msix_fh_int_causes {
> > > + MSIX_FH_INT_CAUSES_0 = BIT(0), /* cause 0 */
> > > + MSIX_FH_INT_CAUSES_1 = BIT(1), /* cause 1 */
> > > +};
> > > +
> > > +/* Causes for the HW register interrupts */
> > > +enum msix_hw_int_causes {
> > > + MSIX_HW_INT_CAUSES_GP0 = BIT(0), /* cause 32 */
> > > +};
> > > +
> > > +#define MSIX_NON_AUTO_CLEAR_CAUSE BIT(7)
> > > +
> > > +/* Minimum and Maximum number of MSIx Vector
> > > + * Intel Bluetooth PCIe support only 1 vector
> > > + */
> > > +#define MSIX_VEC_MAX 1
> > > +#define MSIX_VEC_MIN 1
> > > +
> > > +/* Default Poll time for MAC access during init*/
> >
> > Missing space at the end.
> Ack.
>
> >
> > > +#define DEFAULT_MAC_ACCESS_TIMEOUT 200000
> >
> > Please specify the unit in the name.
> >
> Ack.
>
> > > +
> > > +/* Default interrupt timeout in msec */
> > > +#define DEFAULT_INTR_TIMEOUT 3000
> >
> > Ditto.
> Ack.
>
> >
> > > +
> > > +/* The number of descriptors in TX/RX queues */
> > > +#define DESCS_COUNT 16
> > > +
> > > +/* Number of Queue for TX and RX
> > > + * It indicates the index of the IA(Index Array)
> > > + */
> > > +enum {
> > > + TXQ_NUM = 0,
> > > + RXQ_NUM = 1,
> > > + NUM_QUEUES = 2,
> > > +};
> > > +
> > > +/* The size of DMA buffer for TX and RX */
> > > +#define BUFFER_SIZE 4096
> >
> > Is that bytes?
> Yes. I will update the same in the above comment.
> >
> > > +
> > > +/* DMA allocation alignment */
> > > +#define DMA_POOL_ALIGNMENT 256
> > > +
> > > +/* TX wait time (jiffies) */
> > > +#define TX_WAIT_TIMEOUT 500
> >
> > Please add the unit to the name.
> Ack.
>
> >
> > > +
> > > +/* Number of pending RX requests for downlink */
> > > +#define RX_MAX_QUEUE 6
> > > +
> > > +/* Enum for RBD buffer size mappting */
> > > +enum {
> > > + RBD_SIZE_1K = 0x1,
> > > + RBD_SIZE_2K = 0x2,
> > > + RBD_SIZE_4K = 0x4,
> > > + RBD_SIZE_8K = 0x8,
> > > + RBD_SIZE_12K = 0x9,
> > > + RBD_SIZE_16K = 0xA,
> > > + RBD_SIZE_20K = 0xB,
> > > + RBD_SIZE_24K = 0xC,
> > > + RBD_SIZE_28K = 0xD,
> > > + RBD_SIZE_32K = 0xE,
> > > +};
> > > +
> > > +/*
> > > + * Struct for Context Information (v2)
> > > + *
> > > + * All members are write-only for host and read-only for device.
> > > + *
> > > + * @version: Version of context information
> > > + * @size: Size of context information
> > > + * @config: Config with which host wants peripheral to execute
> > > + * Subset of capability register published by device
> > > + * @addr_tr_hia: Address of TR Head Index Array
> > > + * @addr_tr_tia: Address of TR Tail Index Array
> > > + * @addr_cr_hia: Address of CR Head Index Array
> > > + * @addr_cr_tia: Address of CR Tail Index Array
> > > + * @num_tr_ia: Number of entries in TR Index Arrays
> > > + * @num_cr_ia: Number of entries in CR Index Arrays
> > > + * @rbd_siz: RBD Size { 0x4=4K }
> > > + * @addr_tfdq: Address of TFD Queue(tx)
> > > + * @addr_urbdq0: Address of URBD Queue(tx)
> > > + * @num_tfdq: Number of TFD in TFD Queue(tx)
> > > + * @num_urbdq0: Number of URBD in URBD Queue(tx)
> > > + * @tfdq_db_vec: Queue number of TFD
> > > + * @urbdq0_db_vec: Queue number of URBD
> > > + * @addr_frbdq: Address of FRBD Queue(rx)
> > > + * @addr_urbdq1: Address of URBD Queue(rx)
> > > + * @num_frbdq: Number of FRBD in FRBD Queue(rx)
> > > + * @frbdq_db_vec: Queue number of FRBD
> > > + * @num_urbdq1: Number of URBD in URBD Queue(rx)
> > > + * @urbdq_db_vec: Queue number of URBDQ1
> > > + * @tr_msi_vec: Transfer Ring MSI Vector
> > > + * @cr_msi_vec: Completion Ring MSI Vector
> > > + * @dbgc_addr: DBGC first fragmemt address
> > > + * @dbgc_size: DBGC buffer size
> > > + * @early_enable: Enarly debug enable
> >
> > Early
> Ack.
>
> >
> > > + * @dbg_output_mode: Debug output mode
> > > + * Bit[4] DBGC O/P { 0=SRAM, 1=DRAM(not relevant for NPK) }
> > > + * Bit[5] DBGC I/P { 0=BDBG, 1=DBGI }
> > > + * Bits[6:7] DBGI O/P(relevant if bit[5] = 1)
> > > + * 0=BT DBGC, 1=WiFi DBGC, 2=NPK }
> > > + * @dbg_preset: Debug preset
> > > + * @ext_addr: Address of context information extension
> > > + * @ext_size: Size of context information part
> > > + *
> > > + * Total 38 DWords
> > > + *
> > > + */
> > > +struct ctx_info {
> > > + u16 version;
> > > + u16 size;
> > > + u32 config;
> > > + u32 reserved_dw02;
> > > + u32 reserved_dw03;
> > > + u64 addr_tr_hia;
> > > + u64 addr_tr_tia;
> > > + u64 addr_cr_hia;
> > > + u64 addr_cr_tia;
> > > + u16 num_tr_ia;
> > > + u16 num_cr_ia;
> > > + u32 rbd_size:4,
> > > + reserved_dw13:28;
> > > + u64 addr_tfdq;
> > > + u64 addr_urbdq0;
> > > + u16 num_tfdq;
> > > + u16 num_urbdq0;
> > > + u16 tfdq_db_vec;
> > > + u16 urbdq0_db_vec;
> > > + u64 addr_frbdq;
> > > + u64 addr_urbdq1;
> > > + u16 num_frbdq;
> > > + u16 frbdq_db_vec;
> > > + u16 num_urbdq1;
> > > + u16 urbdq_db_vec;
> > > + u16 tr_msi_vec;
> > > + u16 cr_msi_vec;
> > > + u32 reserved_dw27;
> > > + u64 dbgc_addr;
> > > + u32 dbgc_size;
> > > + u32 early_enable:1,
> > > + reserved_dw31:3,
> > > + dbg_output_mode:4,
> > > + dbg_preset:8,
> > > + reserved2_dw31:16;
> > > + u64 ext_addr;
> > > + u32 ext_size;
> > > + u32 test_param;
> > > + u32 reserved_dw36;
> > > + u32 reserved_dw37;
> > > +} __packed;
> > > +
> > > +/* Transfer Descriptor for TX
> > > + * @type: Not in use. Set to 0x0
> > > + * @size: Size of data in the buffer
> > > + * @addr: DMA Address of buffer
> > > + */
> > > +struct tfd {
> > > + u8 type;
> > > + u16 size;
> > > + u8 reserved;
> > > + u64 addr;
> > > + u32 reserved1;
> > > +} __packed;
> > > +
> > > +/* URB Descriptor for TX
> > > + * @tfd_index: Index of TFD in TFDQ + 1
> > > + * @num_txq: Queue index of TFD Queue
> > > + * @cmpl_count: Completion count. Always 0x01
> > > + * @immediate_cmpl: Immediate completion flag: Always 0x01
> > > + */
> > > +struct urbd0 {
> > > + u32 tfd_index:16,
> > > + num_txq:8,
> > > + cmpl_count:4,
> > > + reserved:3,
> > > + immediate_cmpl:1;
> > > +} __packed;
> > > +
> > > +/* FRB Descriptor for RX
> > > + * @tag: RX buffer tag (index of RX buffer queue)
> > > + * @addr: Address of buffer
> > > + */
> > > +struct frbd {
> > > + u32 tag:16,
> > > + reserved:16;
> > > + u32 reserved2;
> > > + u64 addr;
> > > +} __packed;
> > > +
> > > +/* URB Descriptor for RX
> > > + * @frbd_tag: Tag from FRBD
> > > + * @status: Status
> > > + */
> > > +struct urbd1 {
> > > + u32 frbd_tag:16,
> > > + status:1,
> > > + reserved:14,
> > > + fixed:1;
> > > +} __packed;
> > > +
> > > +/* RFH header in RX packet
> > > + * @packet_len: Length of the data in the buffer
> > > + * @rxq: RX Queue number
> > > + * @cmd_id: Command ID. Not in Use
> > > + */
> > > +struct rfh_hdr {
> > > + u64 packet_len:16,
> > > + rxq:6,
> > > + reserved:10,
> > > + cmd_id:16,
> > > + reserved1:16;
> > > +} __packed;
> > > +
> > > +/* Internal data buffer
> > > + * @data: pointer to the data buffer
> > > + * @p_addr: physical address of data buffer
> > > + */
> > > +struct data_buf {
> > > + u8 *data;
> > > + dma_addr_t data_p_addr;
> > > +};
> > > +
> > > +/* Index Array */
> > > +struct ia {
> > > + dma_addr_t tr_hia_p_addr;
> > > + u16 *tr_hia;
> > > + dma_addr_t tr_tia_p_addr;
> > > + u16 *tr_tia;
> > > + dma_addr_t cr_hia_p_addr;
> > > + u16 *cr_hia;
> > > + dma_addr_t cr_tia_p_addr;
> > > + u16 *cr_tia;
> > > +};
> > > +
> > > +/* Structure for TX Queue
> > > + * @count: Number of descriptors
> > > + * @tfds: Array of TFD
> > > + * @urbd0s: Array of URBD0
> > > + * @buf: Array of data_buf structure
> > > + */
> > > +struct txq {
> > > + u16 count;
> > > +
> > > + dma_addr_t tfds_p_addr;
> > > + struct tfd *tfds;
> > > +
> > > + dma_addr_t urbd0s_p_addr;
> > > + struct urbd0 *urbd0s;
> > > +
> > > + dma_addr_t buf_p_addr;
> > > + void *buf_v_addr;
> > > + struct data_buf *bufs;
> > > +};
> > > +
> > > +/* Structure for RX Queue
> > > + * @count: Number of descriptors
> > > + * @frbds: Array of FRBD
> > > + * @urbd1s: Array of URBD1
> > > + * @buf: Array of data_buf structure
> > > + */
> > > +struct rxq {
> > > + u16 count;
> > > +
> > > + dma_addr_t frbds_p_addr;
> > > + struct frbd *frbds;
> > > +
> > > + dma_addr_t urbd1s_p_addr;
> > > + struct urbd1 *urbd1s;
> > > +
> > > + dma_addr_t buf_p_addr;
> > > + void *buf_v_addr;
> > > + struct data_buf *bufs;
> > > +};
> > > +
> > > +/* struct btintel_pcie_data
> > > + * @pdev: pci device
> > > + * @hdev: hdev device
> > > + * @flags: driver state
> > > + * @irq_lock: spinlock for MSIX
> > > + * @hci_rx_lock: spinlock for HCI RX flow
> > > + * @base_addr: pci base address (from BAR)
> > > + * @msix_entries: array of MSIX entries
> > > + * @msix_enabled: true if MSIX is enabled;
> > > + * @alloc_vecs: number of interrupt vectors allocated
> > > + * @def_irq: default irq for all causes
> > > + * @fh_init_mask: initial unmasked rxq causes
> > > + * @hw_init_mask: initial unmaksed hw causes
> > > + * @boot_stage_cache: cached value of boot stage register
> > > + * @img_resp_cache: cached value of image response register
> > > + * @cnvi: CNVi register value
> > > + * @cnvr: CNVr register value
> > > + * @gp0_received: condition for gp0 interrupt
> > > + * @gp0_wait_q: wait_q for gp0 interrupt
> > > + * @tx_wait_done: condition for tx interrupt
> > > + * @tx_wait_q: wait_q for tx interrupt
> > > + * @workqueue: workqueue for RX work
> > > + * @rx_skb_q: SKB queue for RX packet
> > > + * @rx_work: RX work struct to process the RX packet in @rx_skb_q
> > > + * @dma_pool: DMA pool for descriptors, index array and ci
> > > + * @dma_p_addr: DMA address for pool
> > > + * @dma_v_addr: address of pool
> > > + * @ci_p_addr: DMA address for CI struct
> > > + * @ci: CI struct
> > > + * @ia: Index Array struct
> > > + * @txq: TX Queue struct
> > > + * @rxq: RX Queue struct
> > > + */
> > > +struct btintel_pcie_data {
> > > + struct pci_dev *pdev;
> > > + struct hci_dev *hdev;
> > > +
> > > + unsigned long flags;
> > > + /* lock used in MSIX interrupt */
> > > + spinlock_t irq_lock;
> > > + /* lock to serialize rx events */
> > > + spinlock_t hci_rx_lock;
> > > +
> > > + void __iomem *base_addr;
> > > +
> > > + struct msix_entry msix_entries[MSIX_VEC_MAX];
> > > + bool msix_enabled;
> > > + u32 alloc_vecs;
> > > + u32 def_irq;
> > > +
> > > + u32 fh_init_mask;
> > > + u32 hw_init_mask;
> > > +
> > > + u32 boot_stage_cache;
> > > + u32 img_resp_cache;
> > > +
> > > + u32 cnvi;
> > > + u32 cnvr;
> > > +
> > > + bool gp0_received;
> > > + wait_queue_head_t gp0_wait_q;
> > > +
> > > + bool tx_wait_done;
> > > + wait_queue_head_t tx_wait_q;
> > > +
> > > + struct workqueue_struct *workqueue;
> > > + struct sk_buff_head rx_skb_q;
> > > + struct work_struct rx_work;
> > > +
> > > + struct dma_pool *dma_pool;
> > > + dma_addr_t dma_p_addr;
> > > + void *dma_v_addr;
> > > +
> > > + dma_addr_t ci_p_addr;
> > > + struct ctx_info *ci;
> > > + struct ia ia;
> > > + struct txq txq;
> > > + struct rxq rxq;
> > > +};
> > > +
> > > +static inline u32 btintel_pcie_rd_reg32(struct btintel_pcie_data *data,
> > > + u32 offset)
> > > +{
> > > + return ioread32(data->base_addr + offset);
> > > +}
> > > +
> > > +static inline void btintel_pcie_wr_reg8(struct btintel_pcie_data *data,
> > > + u32 offset, u8 val)
> > > +{
> > > + iowrite8(val, data->base_addr + offset);
> > > +}
> > > +
> > > +static inline void btintel_pcie_wr_reg32(struct btintel_pcie_data *data,
> > > + u32 offset, u32 val)
> > > +{
> > > + iowrite32(val, data->base_addr + offset);
> > > +}
> > > +
> > > +static inline void btintel_pcie_set_reg_bits(struct btintel_pcie_data *data,
> > > + u32 offset, u32 bits)
> > > +{
> > > + u32 r;
> > > +
> > > + r = ioread32(data->base_addr + offset);
> > > + r |= bits;
> > > + iowrite32(r, data->base_addr + offset);
> > > +}
> > > +
> > > +static inline void btintel_pcie_clr_reg_bits(struct btintel_pcie_data *data,
> > > + u32 offset, u32 bits)
> > > +{
> > > + u32 r;
> > > +
> > > + r = ioread32(data->base_addr + offset);
> > > + r &= ~bits;
> > > + iowrite32(r, data->base_addr + offset);
> > > +}
> >
> >
> > Kind regards,
> >
> > Paul
>
> Thanks,
> Kiran
>
--
Luiz Augusto von Dentz
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH v1 2/3] Bluetooth: btintel_pcie: Add support for PCIE transport
2024-03-28 11:19 ` [PATCH v1 2/3] Bluetooth: btintel_pcie: Add support for PCIE transport Kiran K
2024-03-28 12:24 ` Paul Menzel
@ 2024-03-28 14:09 ` Luiz Augusto von Dentz
2024-03-28 14:13 ` Luiz Augusto von Dentz
2024-05-07 14:39 ` K, Kiran
2024-03-28 17:08 ` Bjorn Helgaas
2 siblings, 2 replies; 16+ messages in thread
From: Luiz Augusto von Dentz @ 2024-03-28 14:09 UTC (permalink / raw)
To: Kiran K
Cc: linux-bluetooth, ravishankar.srivatsa, chethan.tumkur.narayan,
Tedd Ho-Jeong An
Hi Kiran,
On Thu, Mar 28, 2024 at 7:05 AM Kiran K <kiran.k@intel.com> wrote:
>
> From: Tedd Ho-Jeong An <tedd.an@intel.com>
>
> Add initial code to support Intel bluetooth devices based on PICE
> transport. This patch allocates memory for buffers, internal structures,
> initializes interrupts for TX & RX and initializes PCIE device.
>
> Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
> Co-developed-by: Kiran K <kiran.k@intel.com>
> Signed-off-by: Kiran K <kiran.k@intel.com>
> ---
> drivers/bluetooth/Kconfig | 14 +
> drivers/bluetooth/Makefile | 1 +
> drivers/bluetooth/btintel.h | 2 +-
> drivers/bluetooth/btintel_pcie.c | 1317 ++++++++++++++++++++++++++++++
> drivers/bluetooth/btintel_pcie.h | 449 ++++++++++
> 5 files changed, 1782 insertions(+), 1 deletion(-)
> create mode 100644 drivers/bluetooth/btintel_pcie.c
> create mode 100644 drivers/bluetooth/btintel_pcie.h
>
> diff --git a/drivers/bluetooth/Kconfig b/drivers/bluetooth/Kconfig
> index bc211c324206..387f7b14461d 100644
> --- a/drivers/bluetooth/Kconfig
> +++ b/drivers/bluetooth/Kconfig
> @@ -23,6 +23,20 @@ config BT_MTK
> tristate
> select FW_LOADER
>
> +config BT_INTEL_PCIE
> + tristate "Intel Bluetooth transport driver for PCIe"
> + depends on PCI
> + select BT_INTEL
> + select FW_LOADER
> + default y
> + help
> + Intel Bluetooth transport driver for PCIe.
> + This driver is required if you want to use Intel Bluetooth device
> + with PCIe interface.
> +
> + Say Y here to compiler support for Intel Bluetooth PCIe device into
> + the kernel or say M to compile it as module (btintel_pcie)
> +
> config BT_HCIBTUSB
> tristate "HCI USB driver"
> depends on USB
> diff --git a/drivers/bluetooth/Makefile b/drivers/bluetooth/Makefile
> index 7a5967e9ac48..0730d6684d1a 100644
> --- a/drivers/bluetooth/Makefile
> +++ b/drivers/bluetooth/Makefile
> @@ -17,6 +17,7 @@ obj-$(CONFIG_BT_HCIBTUSB) += btusb.o
> obj-$(CONFIG_BT_HCIBTSDIO) += btsdio.o
>
> obj-$(CONFIG_BT_INTEL) += btintel.o
> +obj-$(CONFIG_BT_INTEL_PCIE) += btintel_pcie.o btintel.o
> obj-$(CONFIG_BT_ATH3K) += ath3k.o
> obj-$(CONFIG_BT_MRVL) += btmrvl.o
> obj-$(CONFIG_BT_MRVL_SDIO) += btmrvl_sdio.o
> diff --git a/drivers/bluetooth/btintel.h b/drivers/bluetooth/btintel.h
> index 1462a57420a0..5d4685b5c1fa 100644
> --- a/drivers/bluetooth/btintel.h
> +++ b/drivers/bluetooth/btintel.h
> @@ -209,7 +209,7 @@ struct btintel_data {
> #define btintel_wait_on_flag_timeout(hdev, nr, m, to) \
> wait_on_bit_timeout(btintel_get_flag(hdev), (nr), m, to)
>
> -#if IS_ENABLED(CONFIG_BT_INTEL)
> +#if IS_ENABLED(CONFIG_BT_INTEL) || IS_ENABLED(CONFIG_BT_INTEL_PCIE)
>
> int btintel_check_bdaddr(struct hci_dev *hdev);
> int btintel_enter_mfg(struct hci_dev *hdev);
> diff --git a/drivers/bluetooth/btintel_pcie.c b/drivers/bluetooth/btintel_pcie.c
> new file mode 100644
> index 000000000000..e6ce2304dc57
> --- /dev/null
> +++ b/drivers/bluetooth/btintel_pcie.c
> @@ -0,0 +1,1317 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +/*
> + * Intel Bluetooth PCIE driver
> + *
> + * Copyright (C) 2017 Intel Corporation. All rights reserved.
The above shall probably be updated to 2024, also the All rights
reserved don't actually fit well with GPL so please remove it.
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License version
> + * 2 as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Copyright (C) 2022 Intel Corporation
See above.
> + * Intel Bluetooth Driver for PCIE interface.
> + */
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/firmware.h>
> +#include <linux/pci.h>
> +#include <linux/wait.h>
> +#include <linux/delay.h>
> +#include <linux/interrupt.h>
> +
> +#include <asm/unaligned.h>
> +
> +#include <net/bluetooth/bluetooth.h>
> +#include <net/bluetooth/hci_core.h>
> +
> +#include "btintel.h"
> +#include "btintel_pcie.h"
> +
> +#define VERSION "0.1"
> +
> +#define BTINTEL_PCI_DEVICE(dev, subdev) \
> + .vendor = PCI_VENDOR_ID_INTEL, \
> + .device = (dev), \
> + .subvendor = PCI_ANY_ID, \
> + .subdevice = (subdev), \
> + .driver_data = 0
> +
> +/* Intel Bluetooth PCIe device id table */
> +static const struct pci_device_id btintel_pcie_table[] = {
> + { BTINTEL_PCI_DEVICE(0xA876, PCI_ANY_ID) },
> + { 0 }
> +};
> +MODULE_DEVICE_TABLE(pci, btintel_pcie_table);
> +
> +/* Intel PCIe uses 4 bytes of HCI type instead of 1 byte BT SIG HCI type */
> +#define BTINTEL_PCIE_HCI_TYPE_LEN 4
> +#define BTINTEL_PCIE_HCI_CMD_PKT 0x00000001
> +#define BTINTEL_PCIE_HCI_ACL_PKT 0x00000002
> +#define BTINTEL_PCIE_HCI_SCO_PKT 0x00000003
> +#define BTINTEL_PCIE_HCI_EVT_PKT 0x00000004
> +
> +#define BTITNEL_PCIE_ENABLE_HCI_DUMP 0
> +
> +#if BTITNEL_PCIE_ENABLE_HCI_DUMP
> +static inline void btintel_pcie_hci_dump(const char *p, const void *b, int s)
> +{
> + const unsigned char *ptr = (const unsigned char *)b;
> + char str[64];
> + int c, i;
> +
> + for (i = c = 0; c < s; c++) {
> + i += snprintf(str + i, sizeof(str) - i, "%02x ", ptr[c]);
> + if ((c > 0 && (c + 1) % 8 == 0) || (c == s - 1)) {
> + BT_DBG("%s: %s", p, str);
> + i = 0;
> + }
> + }
> +}
> +#else
> +static inline void btintel_pcie_hci_dump(const char *p, const void *b, int s)
> +{
> +}
> +#endif
We have the monitor to process HCI traffic, not really sure what is
the purpose with the functions above.
> +static void ipc_print_ia_ring(struct ia *ia, u16 queue_num)
> +{
> + BT_DBG("[%s] ---------------- ia ----------------",
> + queue_num == TXQ_NUM ? "TXQ" : "RXQ");
> + BT_DBG("[%s] tr-h:%02u tr-t:%02u cr-h:%02u cr-t:%02u",
> + queue_num == TXQ_NUM ? "TXQ" : "RXQ",
> + ia->tr_hia[queue_num], ia->tr_tia[queue_num],
> + ia->cr_hia[queue_num], ia->cr_tia[queue_num]);
> +}
> +
> +static void ipc_print_urbd0(struct urbd0 *urbd0, u16 index)
> +{
> + BT_DBG("[TXQ] -------------- urbd0[%u] --------------", index);
> + BT_DBG("[TXQ] tfd_index:%u num_txq:%u cmpl_cnt:%u immediate_cmpl:0x%x",
> + urbd0->tfd_index, urbd0->num_txq, urbd0->cmpl_count,
> + urbd0->immediate_cmpl);
> +}
> +
> +static void ipc_print_frbd(struct frbd *frbd, u16 index)
> +{
> + BT_DBG("[RXQ] -------------- frbd[%u] --------------", index);
> + BT_DBG("[RXQ] tag:%u addr:0x%llx", frbd->tag, frbd->addr);
> +}
> +
> +static void ipc_print_urbd1(struct urbd1 *urbd1, u16 index)
> +{
> + BT_DBG("[RXQ] -------------- urbd1[%u] --------------", index);
> + BT_DBG("[RXQ] frbd_tag:%u status: 0x%x fixed:0x%x",
> + urbd1->frbd_tag, urbd1->status, urbd1->fixed);
> +}
We need to replace usage of BT_DBG with bt_dev_dbg, etc.
> +/* Poll internal in microseconds */
> +#define POLL_INTERVAL 10
> +
> +static int btintel_pcie_poll_bit(struct btintel_pcie_data *data, u32 offset,
> + u32 bits, u32 mask, int timeout)
> +{
> + int t = 0;
> + u32 reg;
> +
> + BT_DBG("Enter poll_bit");
> + do {
> + reg = btintel_pcie_rd_reg32(data, offset);
> + BT_DBG("CURRENT FUNC_CTRL_REG: 0x%x", reg);
> +
> + if ((reg & mask) == (bits & mask)) {
> + BT_DBG("Poll bit matched");
> + return t;
> + }
> + udelay(POLL_INTERVAL);
> + t += POLL_INTERVAL;
> + BT_DBG("Poll wait: %d", t);
> + } while (t < timeout);
Way too much debugging for such a trivial function, I'd actually
remove all calls to BT_DBG here.
> + return -ETIMEDOUT;
> +}
> +
> +static struct btintel_pcie_data *btintel_pcie_get_data(struct msix_entry *entry)
> +{
> + u8 queue = entry->entry;
> + struct msix_entry *entries = entry - queue;
> +
> + return container_of(entries, struct btintel_pcie_data, msix_entries[0]);
> +}
> +
> +/* Set the doorbell for RXQ to notify the device that @index(actually index-1)
> + * is available to receive the data
> + */
> +static void btintel_pcie_set_rx_db(struct btintel_pcie_data *data, u16 index)
> +{
> + u32 val;
> +
> + val = index;
> + val |= (513 << 16);
> +
> + BT_DBG("[RXQ] Set doorbell for index: %u", index);
> + btintel_pcie_wr_reg32(data, CSR_HBUS_TARG_WRPTR, val);
> +}
> +
> +/* Update the FRBD(free buffer descriptor) with the @frbd_index and the
> + * DMA address of the free buffer.
> + */
> +static void btintel_pcie_prepare_rx(struct rxq *rxq, u16 frbd_index)
> +{
> + struct data_buf *buf;
> + struct frbd *frbd;
> +
> + /* Get the buffer of the frbd for DMA */
> + buf = &rxq->bufs[frbd_index];
> +
> + frbd = &rxq->frbds[frbd_index];
> + memset(frbd, 0, sizeof(*frbd));
> +
> + /* Update FRBD */
> + frbd->tag = frbd_index;
> + frbd->addr = buf->data_p_addr;
> + ipc_print_frbd(frbd, frbd_index);
> +}
> +
> +static int btintel_pcie_submit_rx(struct btintel_pcie_data *data)
> +{
> + u16 frbd_index;
> + struct rxq *rxq = &data->rxq;
> +
> + /* Read the frbd index from the TR_HIA(Head Index Array) for RXQ */
> + frbd_index = data->ia.tr_hia[RXQ_NUM];
> + BT_DBG("[RXQ] current frbd_index: %u", frbd_index);
> +
> + /* Make sure the index value is within the range. It shouldn't be
> + * bigger than the total count of the queue.
> + */
> + if (frbd_index > rxq->count) {
> + BT_ERR("[RXQ] RXQ out of range: (0x%x)", frbd_index);
> + return -ERANGE;
> + }
> +
> + /* Prepare for RX submit. It updates the FRBD with the address of DMA
> + * buffer
> + */
> + btintel_pcie_prepare_rx(rxq, frbd_index);
> +
> + /* Update TR_HIA with new FRBD index */
> + frbd_index = (frbd_index + 1) % rxq->count;
> + data->ia.tr_hia[RXQ_NUM] = frbd_index;
> + ipc_print_ia_ring(&data->ia, RXQ_NUM);
> +
> + /* Set the doorbell to notify the device */
> + btintel_pcie_set_rx_db(data, frbd_index);
> +
> + BT_DBG("[RXQ] rx sumbit completed");
> +
> + return 0;
> +}
> +
> +static int btintel_pcie_start_rx(struct btintel_pcie_data *data)
> +{
> + int i, ret;
> +
> + for (i = 0; i < RX_MAX_QUEUE; i++) {
> + ret = btintel_pcie_submit_rx(data);
> + if (ret) {
> + BT_ERR("[RXQ] failed to submit frbd(%d)", ret);
> + return ret;
> + }
> + }
> +
> + return 0;
> +}
> +
> +static void btintel_pcie_reset_ia(struct btintel_pcie_data *data)
> +{
> + memset(data->ia.tr_hia, 0, sizeof(u16) * NUM_QUEUES);
> + memset(data->ia.tr_tia, 0, sizeof(u16) * NUM_QUEUES);
> + memset(data->ia.cr_hia, 0, sizeof(u16) * NUM_QUEUES);
> + memset(data->ia.cr_tia, 0, sizeof(u16) * NUM_QUEUES);
> + BT_DBG("Index Arrays are reset");
> +}
> +
> +static void btintel_pcie_reset_bt(struct btintel_pcie_data *data)
> +{
> + BT_INFO("Reset BT Function ");
> + btintel_pcie_wr_reg32(data, CSR_FUNC_CTRL_REG, CSR_FUNC_CTRL_SW_RESET);
> +}
> +
> +/* This function enables BT function by setting CSR_FUNC_CTRL_MAC_INIT bit in
> + * CSR_FUNC_CTRL_REG register and wait for MSI-X with MSIX_HW_INT_CAUSES_GP0.
> + * Then the host reads firmware version from CSR_F2D_MBX and the boot stage
> + * from CSR_BOOT_STAGE_REG.
> + */
> +static int btintel_pcie_enable_bt(struct btintel_pcie_data *data)
> +{
> + int err;
> + u32 reg;
> +
> + data->gp0_received = false;
> +
> + /* Update the DMA address of CI struct to CSR */
> + btintel_pcie_wr_reg32(data, CSR_CI_ADDR_LSB_REG,
> + data->ci_p_addr & 0xffffffff);
> + btintel_pcie_wr_reg32(data, CSR_CI_ADDR_MSB_REG,
> + data->ci_p_addr >> 32);
> +
> + /* Reset the cached value of boot stage. it is updated by the msix
> + * gp0 interrupt handler.
> + */
> + data->boot_stage_cache = 0x0;
> +
> + /* Set MAC_INIT bit to start primary bootloader */
> + reg = btintel_pcie_rd_reg32(data, CSR_FUNC_CTRL_REG);
> + BT_INFO("Before: FUNC_CTRL_REG: 0x%x", reg);
> +
> + btintel_pcie_set_reg_bits(data, CSR_FUNC_CTRL_REG,
> + CSR_FUNC_CTRL_MAC_INIT);
> + BT_INFO("MAC_INIT is set");
It is useless to printing this sort of information, let alone using BT_INFO...
> + /* Wait until MAC_ACCESS is granted */
> + err = btintel_pcie_poll_bit(data, CSR_FUNC_CTRL_REG,
> + CSR_FUNC_CTRL_MAC_ACCESS_STS,
> + CSR_FUNC_CTRL_MAC_ACCESS_STS,
> + DEFAULT_MAC_ACCESS_TIMEOUT);
> + if (err < 0) {
> + BT_ERR("Failed to start bootloader even after %u ns",
> + DEFAULT_MAC_ACCESS_TIMEOUT);
> + return -ENODEV;
> + }
> +
> + /* MAC is ready. Enable BT FUNC */
> + btintel_pcie_set_reg_bits(data, CSR_FUNC_CTRL_REG,
> + CSR_FUNC_CTRL_FUNC_ENA |
> + CSR_FUNC_CTRL_FUNC_INIT);
> +
> + reg = btintel_pcie_rd_reg32(data, CSR_FUNC_CTRL_REG);
> + BT_INFO("After: FUNC_CTRL_REG: 0x%x", reg);
Ditto.
> + /* wait for interrupt from the device after booting up to primary
> + * bootloader.
> + */
> + err = wait_event_timeout(data->gp0_wait_q, data->gp0_received,
> + msecs_to_jiffies(DEFAULT_INTR_TIMEOUT));
> + if (!err) {
> + BT_ERR("Failed to receive mac_init interrupt");
> + return -ETIME;
> + }
> +
> + /* Check cached boot stage is CSR_BOOT_STAGE_ROM(BIT(0)) */
> + if (~data->boot_stage_cache & CSR_BOOT_STAGE_ROM) {
> + BT_ERR("Device is not running in rom");
> + return -ENODEV;
> + }
> +
> + return 0;
> +}
> +
> +/* This function handles the MSI-X interrupt for gp0 cause(bit 0 in
> + * CSR_MSIX_HW_INT_CAUSES) which is sent for boot stage and image response.
> + */
> +static void btintel_pcie_msix_gp0_handler(struct btintel_pcie_data *data)
> +{
> + u32 reg;
> +
> + /* This interrupt is for three different causes and it is not easy to
> + * know what causes the interrupt. So, it compares each register value
> + * with cached value and update it before it wake up the queue.
> + */
> + reg = btintel_pcie_rd_reg32(data, CSR_BOOT_STAGE_REG);
> + if (reg != data->boot_stage_cache) {
> + data->boot_stage_cache = reg;
> +
> + BT_DBG("Boot Stage updated: 0x%x", reg);
> + }
> +
> + reg = btintel_pcie_rd_reg32(data, CSR_IMG_RESPONSE_REG);
> + if (reg != data->img_resp_cache) {
> + data->img_resp_cache = reg;
> +
> + BT_DBG("Image Response updated: 0x%x", reg);
> + }
> +
> + BT_DBG("---------- cached GP0 registers ----------");
> + BT_DBG("Cached Boot Stage Reg: 0x%x", data->boot_stage_cache);
> + BT_DBG("Cached Image Resp Reg: 0x%x", data->img_resp_cache);
> +
> + data->gp0_received = true;
> +
> + /* If the boot stage is OP or IML, reset IA and start RX again */
> + if (data->boot_stage_cache & CSR_BOOT_STAGE_OPFW ||
> + data->boot_stage_cache & CSR_BOOT_STAGE_IML) {
> + btintel_pcie_reset_ia(data);
> + btintel_pcie_start_rx(data);
> + }
> +
> + wake_up(&data->gp0_wait_q);
> +}
> +
> +/* This function handles the MSX-X interrupt for rx queue 0 which is for TX
> + */
> +static void btintel_pcie_msix_tx_handle(struct btintel_pcie_data *data)
> +{
> + u16 cr_tia, cr_hia;
> + struct txq *txq;
> + struct urbd0 *urbd0;
> +
> + cr_tia = data->ia.cr_tia[TXQ_NUM];
> + cr_hia = data->ia.cr_hia[TXQ_NUM];
> +
> + BT_DBG("[TXQ] cr_hia=%u cr_tia=%u", cr_hia, cr_tia);
> +
> + /* Check CR_TIA and CR_HIA for change */
> + if (cr_tia == cr_hia) {
> + BT_ERR("[TXQ] no new CD found");
> + return;
> + }
> +
> + txq = &data->txq;
> +
> + while (cr_tia != cr_hia) {
> + BT_DBG("[TXQ] wake up tx_wait_q");
> +
> + data->tx_wait_done = true;
> + wake_up(&data->tx_wait_q);
> +
> + /* Get URBD0 pointed by cr_tia */
> + urbd0 = &txq->urbd0s[cr_tia];
> + ipc_print_urbd0(urbd0, cr_tia);
> +
> + /* Make sure the completed TFD index is within the range */
> + if (urbd0->tfd_index > txq->count) {
> + BT_ERR("[TXQ] out of range: (0x%x)", urbd0->tfd_index);
> + return;
> + }
> +
> + /* Increase cr_tia */
> + cr_tia = (cr_tia + 1) % txq->count;
> + data->ia.cr_tia[TXQ_NUM] = cr_tia;
> + ipc_print_ia_ring(&data->ia, TXQ_NUM);
> + }
> +}
> +
> +static int btintel_pcie_recv_event_intel(struct hci_dev *hdev,
> + struct sk_buff *skb)
> +{
> + if (btintel_test_flag(hdev, INTEL_BOOTLOADER)) {
> + struct hci_event_hdr *hdr = (void *)skb->data;
> +
> + if (skb->len > HCI_EVENT_HDR_SIZE && hdr->evt == 0xff &&
> + hdr->plen > 0) {
> + const void *ptr = skb->data + HCI_EVENT_HDR_SIZE + 1;
> + unsigned int len = skb->len - HCI_EVENT_HDR_SIZE - 1;
> +
> + switch (skb->data[2]) {
> + case 0x02:
> + /* When switching to the operational firmware
> + * the device sends a vendor specific event
> + * indicating that the bootup completed.
> + */
> + btintel_bootup(hdev, ptr, len);
> + break;
> + case 0x06:
> + /* When the firmware loading completes the
> + * device sends out a vendor specific event
> + * indicating the result of the firmware
> + * loading.
> + */
> + btintel_secure_send_result(hdev, ptr, len);
> + break;
> + }
> + }
> + }
> +
> + return hci_recv_frame(hdev, skb);
> +}
Replace the above with btintel_recv_event?
> +/* Process the received rx data
> + * It check the frame header to identify the data type and create skb
> + * and calling HCI API
> + */
> +static int btintel_pcie_hci_recv_frame(struct btintel_pcie_data *data,
> + void *buf, int count)
> +{
> + struct hci_dev *hdev = data->hdev;
> + int ret;
> + u32 pkt_type;
> + u16 plen;
> + struct sk_buff *skb;
> +
> + spin_lock(&data->hci_rx_lock);
> +
> + /* The first 4 bytes indicates the Intel PCIe specific packet type.
> + * Read the packet type here before remove it.
> + */
> + pkt_type = get_unaligned_le32(buf);
> + bt_dev_dbg(hdev, "pkt_type=%u count=%d", pkt_type, count);
> +
> + buf += BTINTEL_PCIE_HCI_TYPE_LEN;
> + count -= BTINTEL_PCIE_HCI_TYPE_LEN;
> +
> + hdev->stat.byte_rx += count;
> +
> + skb = bt_skb_alloc(count, GFP_ATOMIC);
> + if (!skb) {
> + bt_dev_err(hdev, "Failed to allocate skb for event");
> + ret = -ENOMEM;
> + goto exit_error;
> + }
> +
> + switch (pkt_type) {
> + case BTINTEL_PCIE_HCI_ACL_PKT:
> + hci_skb_pkt_type(skb) = HCI_ACLDATA_PKT;
> + memcpy(skb_put(skb, HCI_ACL_HDR_SIZE), buf, HCI_ACL_HDR_SIZE);
> + plen = hci_acl_hdr(skb)->dlen;
> + buf += HCI_ACL_HDR_SIZE;
> + break;
> + case BTINTEL_PCIE_HCI_SCO_PKT:
> + hci_skb_pkt_type(skb) = HCI_SCODATA_PKT;
> + memcpy(skb_put(skb, HCI_SCO_HDR_SIZE), buf, HCI_SCO_HDR_SIZE);
> + plen = hci_sco_hdr(skb)->dlen;
> + buf += HCI_SCO_HDR_SIZE;
> + break;
> + case BTINTEL_PCIE_HCI_EVT_PKT:
> + hci_skb_pkt_type(skb) = HCI_EVENT_PKT;
> + memcpy(skb_put(skb, HCI_EVENT_HDR_SIZE), buf,
> + HCI_EVENT_HDR_SIZE);
> + plen = hci_event_hdr(skb)->plen;
> + buf += HCI_EVENT_HDR_SIZE;
> + break;
> + default:
> + ret = -EILSEQ;
> + kfree_skb(skb);
> + goto exit_error;
> + }
> + memcpy(skb_put(skb, plen), buf, plen);
This is very unsafe, to say the least, since we are not checking if
buf actually contains all the data since we never seem to use the
count parameter.
> +
> + if (pkt_type == BTINTEL_PCIE_HCI_EVT_PKT)
> + ret = btintel_pcie_recv_event_intel(hdev, skb);
> + else
> + ret = hci_recv_frame(hdev, skb);
> +
> +exit_error:
> + if (ret)
> + hdev->stat.err_rx++;
> +
> + spin_unlock(&data->hci_rx_lock);
> +
> + return ret;
> +}
Hmm, this doesn't sound quite right compared to the likes of
h4_recv_buf, are we guaranteed to only receive complete packets for
example?
> +/* RX work queue */
> +static void btintel_pcie_rx_work(struct work_struct *work)
> +{
> + struct btintel_pcie_data *data = container_of(work,
> + struct btintel_pcie_data, rx_work);
> + struct sk_buff *skb;
> + int err;
> +
> + /* Process the sk_buf in queue and send to the hci layer */
> + while ((skb = skb_dequeue(&data->rx_skb_q))) {
> + err = btintel_pcie_hci_recv_frame(data, skb->data, skb->len);
If the data comes as skb then pass the skb and not just the data, len,
that way we can actually make use of things like skb_pull_data to
advance in the buffer, etc.
> + if (err) {
> + BT_ERR("Failed to send received frame: %d", err);
> + kfree_skb(skb);
> + }
> + }
> +}
> +
> +/* create the sk_buff with data and save it to queue and start rx work
> + */
> +static int btintel_pcie_submit_rx_work(struct btintel_pcie_data *data, u8 status,
> + void *buf)
> +{
> + int ret, len;
> + struct rfh_hdr *rfh_hdr;
> + struct sk_buff *skb;
> +
> + rfh_hdr = (struct rfh_hdr *)buf;
> + btintel_pcie_hci_dump("RFH HDR", buf, sizeof(*rfh_hdr));
> +
> + len = rfh_hdr->packet_len;
> +
> + /* Remove RFH header */
> + buf += sizeof(*rfh_hdr);
> + btintel_pcie_hci_dump("RX", buf, len);
> +
> + /* Create the sk_buf with packet in the buf and save it to sk_buf queue
> + */
> + skb = alloc_skb(len, GFP_ATOMIC);
> + if (!skb) {
> + ret = -ENOMEM;
> + goto resubmit;
> + }
> +
> + /* Copy the data to skb */
> + memcpy(skb_put(skb, len), buf, len);
> +
> + /* Save the skb to rx queue */
> + skb_queue_tail(&data->rx_skb_q, skb);
> +
> + /* Calling rx_work queue to process the skb */
> + queue_work(data->workqueue, &data->rx_work);
> +
> +resubmit:
> + BT_DBG("submit next read request");
> +
> + /* submit read */
> + ret = btintel_pcie_submit_rx(data);
> +
> + return ret;
> +}
> +
> +/* This function handles the MSI-X interrupt for rx queue 1 which is for RX
> + */
> +static void btintel_pcie_msix_rx_handle(struct btintel_pcie_data *data)
> +{
> + u16 cr_hia, cr_tia;
> + struct rxq *rxq;
> + struct urbd1 *urbd1;
> + struct frbd *frbd;
> + struct data_buf *buf;
> + int ret;
> +
> + cr_hia = data->ia.cr_hia[RXQ_NUM];
> + cr_tia = data->ia.cr_tia[RXQ_NUM];
> +
> + BT_DBG("[RXQ] cr_hia=%u cr_tia=%u", cr_hia, cr_tia);
> +
> + /* Check CR_TIA and CR_HIA for change */
> + if (cr_tia == cr_hia) {
> + BT_ERR("[RXQ] no new CD found");
> + return;
> + }
> +
> + rxq = &data->rxq;
> +
> + /* The firmware sends multiple CD in a single MSIX and it needs to
> + * process all received CDs in this interrupt.
> + */
> + while (cr_tia != cr_hia) {
> + /* Get URBD1 pointed by cr_tia */
> + urbd1 = &rxq->urbd1s[cr_tia];
> + ipc_print_urbd1(urbd1, cr_tia);
> +
> + /* Get FRBD poined by urbd1->frbd_tag */
> + frbd = &rxq->frbds[urbd1->frbd_tag];
> +
> + /* Get buf from FRBD tag */
> + buf = &rxq->bufs[urbd1->frbd_tag];
> + if (!buf) {
> + BT_ERR("[RXQ] failed to get the DMA buffer for %d",
> + urbd1->frbd_tag);
> + return;
> + }
> +
> + /* prepare RX work */
> + ret = btintel_pcie_submit_rx_work(data, urbd1->status,
> + buf->data);
> + if (ret) {
> + BT_ERR("[RXQ] failed to submit rx request");
> + return;
> + }
> +
> + /* Update cr_tia */
> + cr_tia = (cr_tia + 1) % rxq->count;
> + data->ia.cr_tia[RXQ_NUM] = cr_tia;
> + ipc_print_ia_ring(&data->ia, RXQ_NUM);
> + }
> + BT_DBG("[RXQ] completed rx interrupt");
> +}
> +
> +static irqreturn_t btintel_pcie_msix_isr(int irq, void *data)
> +{
> + return IRQ_WAKE_THREAD;
> +}
> +
> +static irqreturn_t btintel_pcie_irq_msix_handler(int irq, void *dev_id)
> +{
> + struct msix_entry *entry = dev_id;
> + struct btintel_pcie_data *data = btintel_pcie_get_data(entry);
> + u32 intr_fh, intr_hw;
> +
> + BT_DBG("handling msix(irq=%d dev_id=0x%p)", irq, dev_id);
> +
> + spin_lock(&data->irq_lock);
> + intr_fh = btintel_pcie_rd_reg32(data, CSR_MSIX_FH_INT_CAUSES);
> + intr_hw = btintel_pcie_rd_reg32(data, CSR_MSIX_HW_INT_CAUSES);
> +
> + /* Clear causes registers to avoid being handling the same cause */
> + btintel_pcie_wr_reg32(data, CSR_MSIX_FH_INT_CAUSES, intr_fh);
> + btintel_pcie_wr_reg32(data, CSR_MSIX_HW_INT_CAUSES, intr_hw);
> + spin_unlock(&data->irq_lock);
> +
> + BT_DBG("intr_fh=0x%x intr_hw=0x%x", intr_fh, intr_hw);
> +
> + if (unlikely(!(intr_fh | intr_hw))) {
> + BT_DBG("Ignore interrupt, inta == 0");
> + return IRQ_NONE;
> + }
> +
> + /* This interrupt is triggered by the firmware after updating
> + * boot_stage register and image_response register
> + */
> + if (intr_hw & MSIX_HW_INT_CAUSES_GP0) {
> + BT_DBG("intr for MSIX_HW_INT_CAUSES_GP0");
> + btintel_pcie_msix_gp0_handler(data);
> + }
> +
> + /* For TX */
> + if (intr_fh & MSIX_FH_INT_CAUSES_0) {
> + BT_DBG("intr for MSIX_FH_INT_CAUSES_0");
> + btintel_pcie_msix_tx_handle(data);
> + }
> +
> + /* For RX */
> + if (intr_fh & MSIX_FH_INT_CAUSES_1) {
> + BT_DBG("intr for MSIX_FH_INT_CAUSES_1");
> + btintel_pcie_msix_rx_handle(data);
> + }
> +
> + /* TODO: Add handler for other causes */
> + /*
> + * Before sending the interrupt the HW disables it to prevent
> + * a nested interrupt. This is done by writing 1 to the corresponding
> + * bit in the mask register. After handling the interrupt, it should be
> + * re-enabled by clearing this bit. This register is defined as
> + * write 1 clear (W1C) register, meaning that it's being clear
> + * by writing 1 to the bit.
> + */
> + btintel_pcie_wr_reg32(data, CSR_MSIX_AUTOMASK_ST, BIT(entry->entry));
> +
> + return IRQ_HANDLED;
> +}
> +
> +/* This function requests the irq for msix and registers the handlers per irq.
> + * Currently, it requests only 1 irq for all interrupt causes.
> + */
> +static int btintel_pcie_setup_irq(struct btintel_pcie_data *data)
> +{
> + int err;
> + int num_irqs, i;
> +
> + BT_DBG("Initialize msix_entries...");
> + for (i = 0; i < MSIX_VEC_MAX; i++) {
> + data->msix_entries[i].entry = i;
> + BT_DBG("msix_entries[%d] vector=0x%x entry=0x%x",
> + i, data->msix_entries[i].vector,
> + data->msix_entries[i].entry);
> + }
> +
> + num_irqs = pci_enable_msix_range(data->pdev, data->msix_entries,
> + MSIX_VEC_MIN,
> + MSIX_VEC_MAX);
> + if (num_irqs < 0) {
> + BT_ERR("Failed to enable msix range (%d)", num_irqs);
> + return num_irqs;
> + }
> +
> + data->alloc_vecs = num_irqs;
> + data->msix_enabled = 1;
> + data->def_irq = 0;
> +
> + BT_DBG("Returned num_irqs=%d", num_irqs);
> + for (i = 0; i < num_irqs; i++) {
> + BT_DBG("msix_entries[%d] vector=0x%x entry=0x%x", i,
> + data->msix_entries[i].vector,
> + data->msix_entries[i].entry);
> + }
> +
> + BT_DBG("setup irq handler");
> + for (i = 0; i < data->alloc_vecs; i++) {
> + struct msix_entry *msix_entry;
> +
> + msix_entry = &data->msix_entries[i];
> +
> + err = devm_request_threaded_irq(&data->pdev->dev,
> + msix_entry->vector,
> + btintel_pcie_msix_isr,
> + btintel_pcie_irq_msix_handler,
> + IRQF_SHARED,
> + KBUILD_MODNAME,
> + msix_entry);
> + if (err) {
> + BT_ERR("Failed to allocate irq handler (%d)", err);
> + return err;
> + }
> + }
> +
> + return 0;
> +}
> +
> +struct btintel_pcie_causes_list {
> + u32 cause;
> + u32 mask_reg;
> + u8 cause_num;
> +};
> +
> +struct btintel_pcie_causes_list causes_list[] = {
> + { MSIX_FH_INT_CAUSES_0, CSR_MSIX_FH_INT_MASK, 0x00 },
> + { MSIX_FH_INT_CAUSES_1, CSR_MSIX_FH_INT_MASK, 0x01 },
> + { MSIX_HW_INT_CAUSES_GP0, CSR_MSIX_HW_INT_MASK, 0x20 },
> +};
> +
> +/* This function configures the interrupt masks for both HW_INT_CAUSES and
> + * FH_INT_CAUSES which are meaningful to us.
> + *
> + * After resetting BT function via PCIE FLR or FUNC_CTRL reset, the driver
> + * need to call this function again to configure it again since the masks
> + * are reset to 0xFFFFFFFF after reset.
> + */
> +static void btintel_pcie_config_msix(struct btintel_pcie_data *data)
> +{
> + int i;
> + int val = data->def_irq | MSIX_NON_AUTO_CLEAR_CAUSE;
> +
> + /* Set Non Auto Clear Cause */
> + for (i = 0; i < ARRAY_SIZE(causes_list); i++) {
> + btintel_pcie_wr_reg8(data,
> + CSR_MSIX_IVAR(causes_list[i].cause_num),
> + val);
> + btintel_pcie_clr_reg_bits(data,
> + causes_list[i].mask_reg,
> + causes_list[i].cause);
> + }
> +
> + /* Save the initial interrupt mask */
> + data->fh_init_mask = ~btintel_pcie_rd_reg32(data, CSR_MSIX_FH_INT_MASK);
> + data->hw_init_mask = ~btintel_pcie_rd_reg32(data, CSR_MSIX_HW_INT_MASK);
> + BT_DBG("init_mask: fh=0x%x hw=0x%x", data->fh_init_mask,
> + data->hw_init_mask);
> +}
> +
> +static int btintel_pcie_config_pcie(struct pci_dev *pdev,
> + struct btintel_pcie_data *data)
> +{
> + int err;
> +
> + err = pcim_enable_device(pdev);
> + if (err) {
> + BT_ERR("Failed to enable pci device (%d)", err);
> + return err;
> + }
> + pci_set_master(pdev);
> +
> + /* Setup DMA mask */
> + BT_DBG("Set DMA_MASK(64)");
> + err = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64));
> + if (err) {
> + BT_DBG("Set DMA_MASK(32)");
> + err = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32));
> + /* Both attempt failed */
> + if (err) {
> + BT_ERR("No suitable DMA available");
> + return err;
> + }
> + }
> +
> + /* Get BAR to access CSR */
> + err = pcim_iomap_regions(pdev, BIT(0), KBUILD_MODNAME);
> + if (err) {
> + BT_ERR("Failed to get iomap regions (%d)", err);
> + return err;
> + }
> +
> + data->base_addr = pcim_iomap_table(pdev)[0];
> + if (!data->base_addr) {
> + BT_ERR("Failed to get base address");
> + return -ENODEV;
> + }
> +
> + err = btintel_pcie_setup_irq(data);
> + if (err) {
> + BT_ERR("Failed to setup irq for msix");
> + return err;
> + }
> +
> + /* Configure MSI-X with causes list */
> + btintel_pcie_config_msix(data);
> +
> + return 0;
> +}
> +
> +static void btintel_pcie_init_ci(struct btintel_pcie_data *data,
> + struct ctx_info *ci)
> +{
> + ci->version = 0x1;
> + ci->size = sizeof(*ci);
> + ci->config = 0x0000;
> + ci->addr_cr_hia = data->ia.cr_hia_p_addr;
> + ci->addr_tr_tia = data->ia.tr_tia_p_addr;
> + ci->addr_cr_tia = data->ia.cr_tia_p_addr;
> + ci->addr_tr_hia = data->ia.tr_hia_p_addr;
> + ci->num_cr_ia = NUM_QUEUES;
> + ci->num_tr_ia = NUM_QUEUES;
> + ci->addr_urbdq0 = data->txq.urbd0s_p_addr;
> + ci->addr_tfdq = data->txq.tfds_p_addr;
> + ci->num_tfdq = data->txq.count;
> + ci->num_urbdq0 = data->txq.count;
> + ci->tfdq_db_vec = TXQ_NUM;
> + ci->urbdq0_db_vec = TXQ_NUM;
> + ci->rbd_size = RBD_SIZE_4K;
> + ci->addr_frbdq = data->rxq.frbds_p_addr;
> + ci->num_frbdq = data->rxq.count;
> + ci->frbdq_db_vec = RXQ_NUM;
> + ci->addr_urbdq1 = data->rxq.urbd1s_p_addr;
> + ci->num_urbdq1 = data->rxq.count;
> + ci->urbdq_db_vec = RXQ_NUM;
> +}
> +
> +static void btintel_pcie_free_txq_bufs(struct btintel_pcie_data *data,
> + struct txq *txq)
> +{
> + /* Free data buffers first */
> + dma_free_coherent(&data->pdev->dev, txq->count * BUFFER_SIZE,
> + txq->buf_v_addr, txq->buf_p_addr);
> + kfree(txq->bufs);
> + BT_DBG("txq buffers are freed");
> +}
> +
> +static int btintel_pcie_setup_txq_bufs(struct btintel_pcie_data *data,
> + struct txq *txq)
> +{
> + int err = 0, i;
> + struct data_buf *buf;
> +
> + if (txq->count == 0) {
> + BT_ERR("invalid parameter: txq->count");
> + err = -EINVAL;
> + goto exit_error;
> + }
> +
> + /* Allocate the same number of buffers as the descriptor */
> + txq->bufs = kmalloc_array(txq->count, sizeof(*buf), GFP_KERNEL);
> + if (!txq->bufs) {
> + err = -ENOMEM;
> + goto exit_error;
> + }
> +
> + /* Allocate full chunk of data buffer for DMA first and do indexing and
> + * initialization next, so it can be freed easily
> + */
> + txq->buf_v_addr = dma_alloc_coherent(&data->pdev->dev,
> + txq->count * BUFFER_SIZE,
> + &txq->buf_p_addr,
> + GFP_KERNEL | __GFP_NOWARN);
> + if (!txq->buf_v_addr) {
> + BT_ERR("Failed to allocate DMA buf");
> + err = -ENOMEM;
> + kfree(txq->bufs);
> + goto exit_error;
> + }
> + memset(txq->buf_v_addr, 0, txq->count * BUFFER_SIZE);
> +
> + BT_DBG("alloc bufs: p=0x%llx v=0x%p", txq->buf_p_addr, txq->buf_v_addr);
> +
> + /* Setup the allocated DMA buffer to bufs. Each data_buf should
> + * have virtual address and physical address
> + */
> + for (i = 0; i < txq->count; i++) {
> + buf = &txq->bufs[i];
> + buf->data_p_addr = txq->buf_p_addr + (i * BUFFER_SIZE);
> + buf->data = txq->buf_v_addr + (i * BUFFER_SIZE);
> + }
> +
> +exit_error:
> + return err;
> +}
> +
> +static void btintel_pcie_free_rxq_bufs(struct btintel_pcie_data *data,
> + struct rxq *rxq)
> +{
> + /* Free data buffers first */
> + dma_free_coherent(&data->pdev->dev, rxq->count * BUFFER_SIZE,
> + rxq->buf_v_addr, rxq->buf_p_addr);
> + kfree(rxq->bufs);
> + BT_DBG("rxq buffers are freed");
> +}
> +
> +static int btintel_pcie_setup_rxq_bufs(struct btintel_pcie_data *data,
> + struct rxq *rxq)
> +{
> + int err = 0, i;
> + struct data_buf *buf;
> +
> + if (rxq->count == 0) {
> + BT_ERR("invalid parameter: rxq->count");
> + err = -EINVAL;
> + goto exit_error;
> + }
> +
> + /* Allocate the same number of buffers as the descriptor */
> + rxq->bufs = kmalloc_array(rxq->count, sizeof(*buf), GFP_KERNEL);
> + if (!rxq->bufs) {
> + err = -ENOMEM;
> + goto exit_error;
> + }
> +
> + /* Allocate full chunk of data buffer for DMA first and do indexing and
> + * initialization next, so it can be freed easily
> + */
> + rxq->buf_v_addr = dma_alloc_coherent(&data->pdev->dev,
> + rxq->count * BUFFER_SIZE,
> + &rxq->buf_p_addr,
> + GFP_KERNEL | __GFP_NOWARN);
> + if (!rxq->buf_v_addr) {
> + BT_ERR("Failed to allocate DMA buf");
> + err = -ENOMEM;
> + kfree(rxq->bufs);
> + goto exit_error;
> + }
> + memset(rxq->buf_v_addr, 0, rxq->count * BUFFER_SIZE);
> +
> + BT_DBG("alloc bufs: p=0x%llx v=0x%p", rxq->buf_p_addr, rxq->buf_v_addr);
> +
> + /* Setup the allocated DMA buffer to bufs. Each data_buf should
> + * have virtual address and physical address
> + */
> + for (i = 0; i < rxq->count; i++) {
> + buf = &rxq->bufs[i];
> + buf->data_p_addr = rxq->buf_p_addr + (i * BUFFER_SIZE);
> + buf->data = rxq->buf_v_addr + (i * BUFFER_SIZE);
> + }
> +
> +exit_error:
> +
> + return err;
> +}
> +
> +static void btintel_pcie_setup_ia(struct btintel_pcie_data *data,
> + dma_addr_t p_addr, void *v_addr,
> + struct ia *ia)
> +{
> + /* TR Head Index Array */
> + ia->tr_hia_p_addr = p_addr;
> + ia->tr_hia = v_addr;
> +
> + /* TR Tail Index Array */
> + ia->tr_tia_p_addr = p_addr + sizeof(u16) * NUM_QUEUES;
> + ia->tr_tia = v_addr + sizeof(u16) * NUM_QUEUES;
> +
> + /* CR Head index Array */
> + ia->cr_hia_p_addr = p_addr + (sizeof(u16) * NUM_QUEUES * 2);
> + ia->cr_hia = v_addr + (sizeof(u16) * NUM_QUEUES * 2);
> +
> + /* CR Tail Index Array */
> + ia->cr_tia_p_addr = p_addr + (sizeof(u16) * NUM_QUEUES * 3);
> + ia->cr_tia = v_addr + (sizeof(u16) * NUM_QUEUES * 3);
> +}
> +
> +static void btintel_pcie_free(struct btintel_pcie_data *data)
> +{
> + btintel_pcie_free_rxq_bufs(data, &data->rxq);
> + btintel_pcie_free_txq_bufs(data, &data->txq);
> +
> + dma_pool_free(data->dma_pool, data->dma_v_addr, data->dma_p_addr);
> + dma_pool_destroy(data->dma_pool);
> + BT_DBG("DMA memory is freed");
Printing this kind of information is useless, we should really make
sure there are no leaks but there are better tools for that then
printing when we free data.
> +}
> +
> +/* Allocate tx and rx queues, any related data structures and buffers.
> + */
> +static int btintel_pcie_alloc(struct btintel_pcie_data *data)
> +{
> + int err = 0;
> + size_t total;
> + dma_addr_t p_addr;
> + void *v_addr;
> +
> + /* Allocate the chunk of DMA memory for descriptors, index array, and
> + * context information, instead of allocating individually.
> + * The DMA memory for data buffer is allocated while setting up the
> + * each queue.
> + *
> + * Total size is sum of the following
> + * + size of TFD * Number of descriptors in queue
> + * + size of URBD0 * Number of descriptors in queue
> + * + size of FRBD * Number of descriptors in queue
> + * + size of URBD1 * Number of descriptors in queue
> + * + size of index * Number of queues(2) * type of index array(4)
> + * + size of context information
> + */
> + total = (sizeof(struct tfd) + sizeof(struct urbd0) + sizeof(struct frbd)
> + + sizeof(struct urbd1)) * DESCS_COUNT;
> +
> + /* Add the sum of size of index array and size of ci struct */
> + total += (sizeof(u16) * NUM_QUEUES * 4) + sizeof(struct ctx_info);
> +
> + /* Allocate DMA Pool */
> + data->dma_pool = dma_pool_create(KBUILD_MODNAME, &data->pdev->dev,
> + total, DMA_POOL_ALIGNMENT, 0);
> + if (!data->dma_pool) {
> + BT_ERR("Failed to allocate dma pool for queues");
> + err = -ENOMEM;
> + goto exit_error;
> + }
> +
> + v_addr = dma_pool_zalloc(data->dma_pool, GFP_KERNEL | __GFP_NOWARN,
> + &p_addr);
> + if (!v_addr) {
> + BT_ERR("Failed to alloc dma memory for queues");
> + dma_pool_destroy(data->dma_pool);
> + err = -ENOMEM;
> + goto exit_error;
> + }
> +
> + data->dma_p_addr = p_addr;
> + data->dma_v_addr = v_addr;
> +
> + BT_DBG("dma pool: p_addr=0x%llx v_addr=0x%p", p_addr, v_addr);
> +
> + /* Setup descriptor count */
> + data->txq.count = DESCS_COUNT;
> + data->rxq.count = DESCS_COUNT;
> +
> + /* Setup tfds */
> + data->txq.tfds_p_addr = p_addr;
> + data->txq.tfds = v_addr;
> +
> + p_addr += (sizeof(struct tfd) * DESCS_COUNT);
> + v_addr += (sizeof(struct tfd) * DESCS_COUNT);
> +
> + /* Setup urbd0 */
> + data->txq.urbd0s_p_addr = p_addr;
> + data->txq.urbd0s = v_addr;
> +
> + p_addr += (sizeof(struct urbd0) * DESCS_COUNT);
> + v_addr += (sizeof(struct urbd0) * DESCS_COUNT);
> +
> + /* Setup frbd */
> + data->rxq.frbds_p_addr = p_addr;
> + data->rxq.frbds = v_addr;
> +
> + p_addr += (sizeof(struct frbd) * DESCS_COUNT);
> + v_addr += (sizeof(struct frbd) * DESCS_COUNT);
> +
> + /* Setup urbd1 */
> + data->rxq.urbd1s_p_addr = p_addr;
> + data->rxq.urbd1s = v_addr;
> +
> + p_addr += (sizeof(struct urbd1) * DESCS_COUNT);
> + v_addr += (sizeof(struct urbd1) * DESCS_COUNT);
> +
> + /* Setup data buffers for txq */
> + err = btintel_pcie_setup_txq_bufs(data, &data->txq);
> + if (err) {
> + BT_ERR("Failed to setup txq buffers: %d", err);
> + goto exit_error_pool;
> + }
> +
> + /* Setup data buffers for rxq */
> + err = btintel_pcie_setup_rxq_bufs(data, &data->rxq);
> + if (err) {
> + BT_ERR("Failed to allocate rxq buffers: %d", err);
> + goto exit_error_txq;
> + }
> +
> + /* Setup Index Array */
> + btintel_pcie_setup_ia(data, p_addr, v_addr, &data->ia);
> +
> + /* Setup Context Information */
> + p_addr += sizeof(u16) * NUM_QUEUES * 4;
> + v_addr += sizeof(u16) * NUM_QUEUES * 4;
> +
> + data->ci = v_addr;
> + data->ci_p_addr = p_addr;
> +
> + /* Initialize the CI */
> + btintel_pcie_init_ci(data, data->ci);
> +
> + return 0;
> +
> +exit_error_txq:
> + btintel_pcie_free_txq_bufs(data, &data->txq);
> +exit_error_pool:
> + dma_pool_free(data->dma_pool, data->dma_v_addr, data->dma_p_addr);
> + dma_pool_destroy(data->dma_pool);
> +exit_error:
> + return err;
> +}
> +
> +static void btintel_pcie_release_hdev(struct btintel_pcie_data *data)
> +{
> + struct hci_dev *hdev;
> +
> + hdev = data->hdev;
> + if (hdev) {
> + hci_unregister_dev(hdev);
> + hci_free_dev(hdev);
> + }
> + data->hdev = NULL;
> +}
> +
> +static int btintel_pcie_setup_hdev(struct btintel_pcie_data *data)
> +{
> + /* TODO: initialize hdev and assign the callbacks to hdev */
> + return -ENODEV;
> +}
> +
> +static int btintel_pcie_probe(struct pci_dev *pdev,
> + const struct pci_device_id *ent)
> +{
> + int err;
> + struct btintel_pcie_data *data;
> +
> + if (!pdev)
> + return -ENODEV;
> +
> + data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
> + if (!data)
> + return -ENOMEM;
> +
> + /* initialize the btintel_pcie data struct */
> + data->pdev = pdev;
> +
> + spin_lock_init(&data->irq_lock);
> + spin_lock_init(&data->hci_rx_lock);
> +
> + init_waitqueue_head(&data->gp0_wait_q);
> + data->gp0_received = false;
> +
> + init_waitqueue_head(&data->tx_wait_q);
> + data->tx_wait_done = false;
> +
> + data->workqueue = alloc_ordered_workqueue(KBUILD_MODNAME, WQ_HIGHPRI);
> + if (!data->workqueue) {
> + BT_ERR("Failed to create workqueue");
> + return -ENOMEM;
> + }
> + skb_queue_head_init(&data->rx_skb_q);
> + INIT_WORK(&data->rx_work, btintel_pcie_rx_work);
> +
> + data->boot_stage_cache = 0x00;
> + data->img_resp_cache = 0x00;
> +
> + /* PCIe specific all to configure it for this device includes
> + * enabling pice device, setting master, reading BAR[0], configuring
> + * MSIx, setting DMA mask, and save the driver data.
> + */
> + err = btintel_pcie_config_pcie(pdev, data);
> + if (err) {
> + BT_ERR("Failed to config pcie (%d)", err);
> + goto exit_error;
> + }
> +
> + /* Set driver data for this PCI device */
> + pci_set_drvdata(pdev, data);
> +
> + /* allocate the IPC struct */
> + err = btintel_pcie_alloc(data);
> + if (err) {
> + BT_ERR("Failed to allocate queues(%d)", err);
> + goto exit_error;
> + }
> +
> + /* Enable BT function */
> + err = btintel_pcie_enable_bt(data);
> + if (err) {
> + BT_ERR("Failed to start bluetooth device(%d)", err);
> + goto exit_error;
> + }
> +
> + /* CNV information (CNVi and CNVr) is in CSR */
> + data->cnvi = btintel_pcie_rd_reg32(data, CSR_HW_REV_REG);
> + BT_DBG("cnvi: 0x%08x", data->cnvi);
> +
> + data->cnvr = btintel_pcie_rd_reg32(data, CSR_RF_ID_REG);
> + BT_DBG("cnvr: 0x%08x", data->cnvr);
> +
> + err = btintel_pcie_start_rx(data);
> + if (err) {
> + BT_ERR("Failed to start rx (%d)", err);
> + goto exit_error;
> + }
> +
> + err = btintel_pcie_setup_hdev(data);
> + if (err) {
> + BT_ERR("Failed to setup HCI module");
> + goto exit_error;
> + }
> +
> + return 0;
> +
> +exit_error:
> + /* reset device before leave */
> + btintel_pcie_reset_bt(data);
> +
> + /* clear bus mastering */
> + pci_clear_master(pdev);
> +
> + /* Unset driver data for PCI device */
> + pci_set_drvdata(pdev, NULL);
> +
> + return err;
> +}
> +
> +static void btintel_pcie_remove(struct pci_dev *pdev)
> +{
> + struct btintel_pcie_data *data;
> +
> + if (!pdev) {
> + BT_ERR("Invalid parameter: pdev");
> + return;
> + }
> +
> + data = pci_get_drvdata(pdev);
> + if (!data) {
> + BT_ERR("data is empty");
> + return;
> + }
> +
> + btintel_pcie_release_hdev(data);
> +
> + flush_work(&data->rx_work);
> +
> + destroy_workqueue(data->workqueue);
> +
> + btintel_pcie_free(data);
> +
> + /* reset device before leave */
> + btintel_pcie_reset_bt(data);
> +
> + /* clear bus mastering */
> + pci_clear_master(pdev);
> +
> + /* Unset driver data for PCI device */
> + pci_set_drvdata(pdev, NULL);
> +}
> +
> +#ifdef CONFIG_PM
> +static int btintel_pcie_suspend(struct device *dev)
> +{
> + /* TODO: Add support suspend */
> + return 0;
> +}
> +
> +static int btintel_pcie_resume(struct device *dev)
> +{
> + /* TODO: Add support resume */
> + return 0;
> +}
> +
> +static SIMPLE_DEV_PM_OPS(btintel_pcie_pm_ops, btintel_pcie_suspend,
> + btintel_pcie_resume);
> +#endif /* CONFIG_PM */
> +
> +static struct pci_driver btintel_pcie_driver = {
> + .name = KBUILD_MODNAME,
> + .id_table = btintel_pcie_table,
> + .probe = btintel_pcie_probe,
> + .remove = btintel_pcie_remove,
> +#ifdef CONFIG_PM
> + .driver.pm = &btintel_pcie_pm_ops,
> +#endif /* CONFIG_PM */
> +};
> +module_pci_driver(btintel_pcie_driver);
> +
> +MODULE_AUTHOR("Tedd Ho-Jeong An <tedd.an@intel.com>");
> +MODULE_DESCRIPTION("Intel Bluetooth PCIe transport driver ver " VERSION);
> +MODULE_VERSION(VERSION);
> +MODULE_LICENSE("GPL");
Botton line: We have to tone down the debbuging since it pretting a
lot of useless information and when it does it prints with old BT_DBG
macros which doesn't print the controller info so on system with
multiple controller that would be impossible to say which controller
is generating the logs.
> diff --git a/drivers/bluetooth/btintel_pcie.h b/drivers/bluetooth/btintel_pcie.h
> new file mode 100644
> index 000000000000..1554964686bd
> --- /dev/null
> +++ b/drivers/bluetooth/btintel_pcie.h
> @@ -0,0 +1,449 @@
> +/* SPDX-License-Identifier: GPL-2.0-or-later */
> +/*
> + * Intel Bluetooth PCIE driver
> + *
> + * Copyright (C) 2017 Intel Corporation. All rights reserved.
Ditto.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License version
> + * 2 as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Copyright (C) 2022 Intel Corporation
> + *
> + * Intel Bluetooth Driver for PCIE interface.
> + */
> +
> +/* Control and Status Register(CSR) */
> +#define CSR_BASE (0x000)
> +#define CSR_FUNC_CTRL_REG (CSR_BASE + 0x024)
> +#define CSR_HW_REV_REG (CSR_BASE + 0x028)
> +#define CSR_RF_ID_REG (CSR_BASE + 0x09C)
> +#define CSR_BOOT_STAGE_REG (CSR_BASE + 0x108)
> +#define CSR_CI_ADDR_LSB_REG (CSR_BASE + 0x118)
> +#define CSR_CI_ADDR_MSB_REG (CSR_BASE + 0x11C)
> +#define CSR_IMG_RESPONSE_REG (CSR_BASE + 0x12C)
> +#define CSR_HBUS_TARG_WRPTR (CSR_BASE + 0x460)
> +
> +/* CSR Function Control Register */
> +#define CSR_FUNC_CTRL_FUNC_ENA (BIT(0))
> +#define CSR_FUNC_CTRL_MAC_INIT (BIT(6))
> +#define CSR_FUNC_CTRL_FUNC_INIT (BIT(7))
> +#define CSR_FUNC_CTRL_MAC_ACCESS_STS (BIT(20))
> +#define CSR_FUNC_CTRL_SW_RESET (BIT(31))
> +
> +/* Value for CSR_BOOT_STAGE register */
> +#define CSR_BOOT_STAGE_ROM (BIT(0))
> +#define CSR_BOOT_STAGE_IML (BIT(1))
> +#define CSR_BOOT_STAGE_OPFW (BIT(2))
> +#define CSR_BOOT_STAGE_ROM_LOCKDOWN (BIT(10))
> +#define CSR_BOOT_STAGE_IML_LOCKDOWN (BIT(11))
> +#define CSR_BOOT_STAGE_MAC_ACCESS_ON (BIT(16))
> +#define CSR_BOOT_STAGE_ALIVE (BIT(23))
> +
> +/* Registers for MSIX */
> +#define CSR_MSIX_BASE (0x2000)
> +#define CSR_MSIX_FH_INT_CAUSES (CSR_MSIX_BASE + 0x0800)
> +#define CSR_MSIX_FH_INT_MASK (CSR_MSIX_BASE + 0x0804)
> +#define CSR_MSIX_HW_INT_CAUSES (CSR_MSIX_BASE + 0x0808)
> +#define CSR_MSIX_HW_INT_MASK (CSR_MSIX_BASE + 0x080C)
> +#define CSR_MSIX_AUTOMASK_ST (CSR_MSIX_BASE + 0x0810)
> +#define CSR_MSIX_AUTOMASK_EN (CSR_MSIX_BASE + 0x0814)
> +#define CSR_MSIX_IVAR_BASE (CSR_MSIX_BASE + 0x0880)
> +#define CSR_MSIX_IVAR(cause) (CSR_MSIX_IVAR_BASE + (cause))
> +
> +/* Causes for the FH register interrupts */
> +enum msix_fh_int_causes {
> + MSIX_FH_INT_CAUSES_0 = BIT(0), /* cause 0 */
> + MSIX_FH_INT_CAUSES_1 = BIT(1), /* cause 1 */
> +};
> +
> +/* Causes for the HW register interrupts */
> +enum msix_hw_int_causes {
> + MSIX_HW_INT_CAUSES_GP0 = BIT(0), /* cause 32 */
> +};
> +
> +#define MSIX_NON_AUTO_CLEAR_CAUSE BIT(7)
> +
> +/* Minimum and Maximum number of MSIx Vector
> + * Intel Bluetooth PCIe support only 1 vector
> + */
> +#define MSIX_VEC_MAX 1
> +#define MSIX_VEC_MIN 1
> +
> +/* Default Poll time for MAC access during init*/
> +#define DEFAULT_MAC_ACCESS_TIMEOUT 200000
> +
> +/* Default interrupt timeout in msec */
> +#define DEFAULT_INTR_TIMEOUT 3000
> +
> +/* The number of descriptors in TX/RX queues */
> +#define DESCS_COUNT 16
> +
> +/* Number of Queue for TX and RX
> + * It indicates the index of the IA(Index Array)
> + */
> +enum {
> + TXQ_NUM = 0,
> + RXQ_NUM = 1,
> + NUM_QUEUES = 2,
> +};
> +
> +/* The size of DMA buffer for TX and RX */
> +#define BUFFER_SIZE 4096
> +
> +/* DMA allocation alignment */
> +#define DMA_POOL_ALIGNMENT 256
> +
> +/* TX wait time (jiffies) */
> +#define TX_WAIT_TIMEOUT 500
> +
> +/* Number of pending RX requests for downlink */
> +#define RX_MAX_QUEUE 6
> +
> +/* Enum for RBD buffer size mappting */
> +enum {
> + RBD_SIZE_1K = 0x1,
> + RBD_SIZE_2K = 0x2,
> + RBD_SIZE_4K = 0x4,
> + RBD_SIZE_8K = 0x8,
> + RBD_SIZE_12K = 0x9,
> + RBD_SIZE_16K = 0xA,
> + RBD_SIZE_20K = 0xB,
> + RBD_SIZE_24K = 0xC,
> + RBD_SIZE_28K = 0xD,
> + RBD_SIZE_32K = 0xE,
> +};
> +
> +/*
> + * Struct for Context Information (v2)
> + *
> + * All members are write-only for host and read-only for device.
> + *
> + * @version: Version of context information
> + * @size: Size of context information
> + * @config: Config with which host wants peripheral to execute
> + * Subset of capability register published by device
> + * @addr_tr_hia: Address of TR Head Index Array
> + * @addr_tr_tia: Address of TR Tail Index Array
> + * @addr_cr_hia: Address of CR Head Index Array
> + * @addr_cr_tia: Address of CR Tail Index Array
> + * @num_tr_ia: Number of entries in TR Index Arrays
> + * @num_cr_ia: Number of entries in CR Index Arrays
> + * @rbd_siz: RBD Size { 0x4=4K }
> + * @addr_tfdq: Address of TFD Queue(tx)
> + * @addr_urbdq0: Address of URBD Queue(tx)
> + * @num_tfdq: Number of TFD in TFD Queue(tx)
> + * @num_urbdq0: Number of URBD in URBD Queue(tx)
> + * @tfdq_db_vec: Queue number of TFD
> + * @urbdq0_db_vec: Queue number of URBD
> + * @addr_frbdq: Address of FRBD Queue(rx)
> + * @addr_urbdq1: Address of URBD Queue(rx)
> + * @num_frbdq: Number of FRBD in FRBD Queue(rx)
> + * @frbdq_db_vec: Queue number of FRBD
> + * @num_urbdq1: Number of URBD in URBD Queue(rx)
> + * @urbdq_db_vec: Queue number of URBDQ1
> + * @tr_msi_vec: Transfer Ring MSI Vector
> + * @cr_msi_vec: Completion Ring MSI Vector
> + * @dbgc_addr: DBGC first fragmemt address
> + * @dbgc_size: DBGC buffer size
> + * @early_enable: Enarly debug enable
> + * @dbg_output_mode: Debug output mode
> + * Bit[4] DBGC O/P { 0=SRAM, 1=DRAM(not relevant for NPK) }
> + * Bit[5] DBGC I/P { 0=BDBG, 1=DBGI }
> + * Bits[6:7] DBGI O/P(relevant if bit[5] = 1)
> + * 0=BT DBGC, 1=WiFi DBGC, 2=NPK }
> + * @dbg_preset: Debug preset
> + * @ext_addr: Address of context information extension
> + * @ext_size: Size of context information part
> + *
> + * Total 38 DWords
> + *
> + */
> +struct ctx_info {
> + u16 version;
> + u16 size;
> + u32 config;
> + u32 reserved_dw02;
> + u32 reserved_dw03;
> + u64 addr_tr_hia;
> + u64 addr_tr_tia;
> + u64 addr_cr_hia;
> + u64 addr_cr_tia;
> + u16 num_tr_ia;
> + u16 num_cr_ia;
> + u32 rbd_size:4,
> + reserved_dw13:28;
> + u64 addr_tfdq;
> + u64 addr_urbdq0;
> + u16 num_tfdq;
> + u16 num_urbdq0;
> + u16 tfdq_db_vec;
> + u16 urbdq0_db_vec;
> + u64 addr_frbdq;
> + u64 addr_urbdq1;
> + u16 num_frbdq;
> + u16 frbdq_db_vec;
> + u16 num_urbdq1;
> + u16 urbdq_db_vec;
> + u16 tr_msi_vec;
> + u16 cr_msi_vec;
> + u32 reserved_dw27;
> + u64 dbgc_addr;
> + u32 dbgc_size;
> + u32 early_enable:1,
> + reserved_dw31:3,
> + dbg_output_mode:4,
> + dbg_preset:8,
> + reserved2_dw31:16;
> + u64 ext_addr;
> + u32 ext_size;
> + u32 test_param;
> + u32 reserved_dw36;
> + u32 reserved_dw37;
> +} __packed;
> +
> +/* Transfer Descriptor for TX
> + * @type: Not in use. Set to 0x0
> + * @size: Size of data in the buffer
> + * @addr: DMA Address of buffer
> + */
> +struct tfd {
> + u8 type;
> + u16 size;
> + u8 reserved;
> + u64 addr;
> + u32 reserved1;
> +} __packed;
> +
> +/* URB Descriptor for TX
> + * @tfd_index: Index of TFD in TFDQ + 1
> + * @num_txq: Queue index of TFD Queue
> + * @cmpl_count: Completion count. Always 0x01
> + * @immediate_cmpl: Immediate completion flag: Always 0x01
> + */
> +struct urbd0 {
> + u32 tfd_index:16,
> + num_txq:8,
> + cmpl_count:4,
> + reserved:3,
> + immediate_cmpl:1;
> +} __packed;
> +
> +/* FRB Descriptor for RX
> + * @tag: RX buffer tag (index of RX buffer queue)
> + * @addr: Address of buffer
> + */
> +struct frbd {
> + u32 tag:16,
> + reserved:16;
> + u32 reserved2;
> + u64 addr;
> +} __packed;
> +
> +/* URB Descriptor for RX
> + * @frbd_tag: Tag from FRBD
> + * @status: Status
> + */
> +struct urbd1 {
> + u32 frbd_tag:16,
> + status:1,
> + reserved:14,
> + fixed:1;
> +} __packed;
> +
> +/* RFH header in RX packet
> + * @packet_len: Length of the data in the buffer
> + * @rxq: RX Queue number
> + * @cmd_id: Command ID. Not in Use
> + */
> +struct rfh_hdr {
> + u64 packet_len:16,
> + rxq:6,
> + reserved:10,
> + cmd_id:16,
> + reserved1:16;
> +} __packed;
> +
> +/* Internal data buffer
> + * @data: pointer to the data buffer
> + * @p_addr: physical address of data buffer
> + */
> +struct data_buf {
> + u8 *data;
> + dma_addr_t data_p_addr;
> +};
> +
> +/* Index Array */
> +struct ia {
> + dma_addr_t tr_hia_p_addr;
> + u16 *tr_hia;
> + dma_addr_t tr_tia_p_addr;
> + u16 *tr_tia;
> + dma_addr_t cr_hia_p_addr;
> + u16 *cr_hia;
> + dma_addr_t cr_tia_p_addr;
> + u16 *cr_tia;
> +};
> +
> +/* Structure for TX Queue
> + * @count: Number of descriptors
> + * @tfds: Array of TFD
> + * @urbd0s: Array of URBD0
> + * @buf: Array of data_buf structure
> + */
> +struct txq {
> + u16 count;
> +
> + dma_addr_t tfds_p_addr;
> + struct tfd *tfds;
> +
> + dma_addr_t urbd0s_p_addr;
> + struct urbd0 *urbd0s;
> +
> + dma_addr_t buf_p_addr;
> + void *buf_v_addr;
> + struct data_buf *bufs;
> +};
> +
> +/* Structure for RX Queue
> + * @count: Number of descriptors
> + * @frbds: Array of FRBD
> + * @urbd1s: Array of URBD1
> + * @buf: Array of data_buf structure
> + */
> +struct rxq {
> + u16 count;
> +
> + dma_addr_t frbds_p_addr;
> + struct frbd *frbds;
> +
> + dma_addr_t urbd1s_p_addr;
> + struct urbd1 *urbd1s;
> +
> + dma_addr_t buf_p_addr;
> + void *buf_v_addr;
> + struct data_buf *bufs;
> +};
> +
> +/* struct btintel_pcie_data
> + * @pdev: pci device
> + * @hdev: hdev device
> + * @flags: driver state
> + * @irq_lock: spinlock for MSIX
> + * @hci_rx_lock: spinlock for HCI RX flow
> + * @base_addr: pci base address (from BAR)
> + * @msix_entries: array of MSIX entries
> + * @msix_enabled: true if MSIX is enabled;
> + * @alloc_vecs: number of interrupt vectors allocated
> + * @def_irq: default irq for all causes
> + * @fh_init_mask: initial unmasked rxq causes
> + * @hw_init_mask: initial unmaksed hw causes
> + * @boot_stage_cache: cached value of boot stage register
> + * @img_resp_cache: cached value of image response register
> + * @cnvi: CNVi register value
> + * @cnvr: CNVr register value
> + * @gp0_received: condition for gp0 interrupt
> + * @gp0_wait_q: wait_q for gp0 interrupt
> + * @tx_wait_done: condition for tx interrupt
> + * @tx_wait_q: wait_q for tx interrupt
> + * @workqueue: workqueue for RX work
> + * @rx_skb_q: SKB queue for RX packet
> + * @rx_work: RX work struct to process the RX packet in @rx_skb_q
> + * @dma_pool: DMA pool for descriptors, index array and ci
> + * @dma_p_addr: DMA address for pool
> + * @dma_v_addr: address of pool
> + * @ci_p_addr: DMA address for CI struct
> + * @ci: CI struct
> + * @ia: Index Array struct
> + * @txq: TX Queue struct
> + * @rxq: RX Queue struct
> + */
> +struct btintel_pcie_data {
> + struct pci_dev *pdev;
> + struct hci_dev *hdev;
> +
> + unsigned long flags;
> + /* lock used in MSIX interrupt */
> + spinlock_t irq_lock;
> + /* lock to serialize rx events */
> + spinlock_t hci_rx_lock;
> +
> + void __iomem *base_addr;
> +
> + struct msix_entry msix_entries[MSIX_VEC_MAX];
> + bool msix_enabled;
> + u32 alloc_vecs;
> + u32 def_irq;
> +
> + u32 fh_init_mask;
> + u32 hw_init_mask;
> +
> + u32 boot_stage_cache;
> + u32 img_resp_cache;
> +
> + u32 cnvi;
> + u32 cnvr;
> +
> + bool gp0_received;
> + wait_queue_head_t gp0_wait_q;
> +
> + bool tx_wait_done;
> + wait_queue_head_t tx_wait_q;
> +
> + struct workqueue_struct *workqueue;
> + struct sk_buff_head rx_skb_q;
> + struct work_struct rx_work;
> +
> + struct dma_pool *dma_pool;
> + dma_addr_t dma_p_addr;
> + void *dma_v_addr;
> +
> + dma_addr_t ci_p_addr;
> + struct ctx_info *ci;
> + struct ia ia;
> + struct txq txq;
> + struct rxq rxq;
> +};
> +
> +static inline u32 btintel_pcie_rd_reg32(struct btintel_pcie_data *data,
> + u32 offset)
> +{
> + return ioread32(data->base_addr + offset);
> +}
> +
> +static inline void btintel_pcie_wr_reg8(struct btintel_pcie_data *data,
> + u32 offset, u8 val)
> +{
> + iowrite8(val, data->base_addr + offset);
> +}
> +
> +static inline void btintel_pcie_wr_reg32(struct btintel_pcie_data *data,
> + u32 offset, u32 val)
> +{
> + iowrite32(val, data->base_addr + offset);
> +}
> +
> +static inline void btintel_pcie_set_reg_bits(struct btintel_pcie_data *data,
> + u32 offset, u32 bits)
> +{
> + u32 r;
> +
> + r = ioread32(data->base_addr + offset);
> + r |= bits;
> + iowrite32(r, data->base_addr + offset);
> +}
> +
> +static inline void btintel_pcie_clr_reg_bits(struct btintel_pcie_data *data,
> + u32 offset, u32 bits)
> +{
> + u32 r;
> +
> + r = ioread32(data->base_addr + offset);
> + r &= ~bits;
> + iowrite32(r, data->base_addr + offset);
> +}
> --
> 2.34.1
All symbols must be properly prefixed with BTINTEL_PCIE
>
--
Luiz Augusto von Dentz
^ permalink raw reply [flat|nested] 16+ messages in thread* Re: [PATCH v1 2/3] Bluetooth: btintel_pcie: Add support for PCIE transport
2024-03-28 14:09 ` Luiz Augusto von Dentz
@ 2024-03-28 14:13 ` Luiz Augusto von Dentz
2024-05-07 14:39 ` K, Kiran
1 sibling, 0 replies; 16+ messages in thread
From: Luiz Augusto von Dentz @ 2024-03-28 14:13 UTC (permalink / raw)
To: Kiran K
Cc: linux-bluetooth, ravishankar.srivatsa, chethan.tumkur.narayan,
Tedd Ho-Jeong An
Hi Kiran,
On Thu, Mar 28, 2024 at 10:09 AM Luiz Augusto von Dentz
<luiz.dentz@gmail.com> wrote:
>
> Hi Kiran,
>
> On Thu, Mar 28, 2024 at 7:05 AM Kiran K <kiran.k@intel.com> wrote:
> >
> > From: Tedd Ho-Jeong An <tedd.an@intel.com>
> >
> > Add initial code to support Intel bluetooth devices based on PICE
> > transport. This patch allocates memory for buffers, internal structures,
> > initializes interrupts for TX & RX and initializes PCIE device.
> >
> > Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
> > Co-developed-by: Kiran K <kiran.k@intel.com>
> > Signed-off-by: Kiran K <kiran.k@intel.com>
> > ---
> > drivers/bluetooth/Kconfig | 14 +
> > drivers/bluetooth/Makefile | 1 +
> > drivers/bluetooth/btintel.h | 2 +-
> > drivers/bluetooth/btintel_pcie.c | 1317 ++++++++++++++++++++++++++++++
> > drivers/bluetooth/btintel_pcie.h | 449 ++++++++++
> > 5 files changed, 1782 insertions(+), 1 deletion(-)
> > create mode 100644 drivers/bluetooth/btintel_pcie.c
> > create mode 100644 drivers/bluetooth/btintel_pcie.h
> >
> > diff --git a/drivers/bluetooth/Kconfig b/drivers/bluetooth/Kconfig
> > index bc211c324206..387f7b14461d 100644
> > --- a/drivers/bluetooth/Kconfig
> > +++ b/drivers/bluetooth/Kconfig
> > @@ -23,6 +23,20 @@ config BT_MTK
> > tristate
> > select FW_LOADER
> >
> > +config BT_INTEL_PCIE
> > + tristate "Intel Bluetooth transport driver for PCIe"
> > + depends on PCI
> > + select BT_INTEL
> > + select FW_LOADER
> > + default y
> > + help
> > + Intel Bluetooth transport driver for PCIe.
> > + This driver is required if you want to use Intel Bluetooth device
> > + with PCIe interface.
> > +
> > + Say Y here to compiler support for Intel Bluetooth PCIe device into
> > + the kernel or say M to compile it as module (btintel_pcie)
> > +
> > config BT_HCIBTUSB
> > tristate "HCI USB driver"
> > depends on USB
> > diff --git a/drivers/bluetooth/Makefile b/drivers/bluetooth/Makefile
> > index 7a5967e9ac48..0730d6684d1a 100644
> > --- a/drivers/bluetooth/Makefile
> > +++ b/drivers/bluetooth/Makefile
> > @@ -17,6 +17,7 @@ obj-$(CONFIG_BT_HCIBTUSB) += btusb.o
> > obj-$(CONFIG_BT_HCIBTSDIO) += btsdio.o
> >
> > obj-$(CONFIG_BT_INTEL) += btintel.o
> > +obj-$(CONFIG_BT_INTEL_PCIE) += btintel_pcie.o btintel.o
> > obj-$(CONFIG_BT_ATH3K) += ath3k.o
> > obj-$(CONFIG_BT_MRVL) += btmrvl.o
> > obj-$(CONFIG_BT_MRVL_SDIO) += btmrvl_sdio.o
> > diff --git a/drivers/bluetooth/btintel.h b/drivers/bluetooth/btintel.h
> > index 1462a57420a0..5d4685b5c1fa 100644
> > --- a/drivers/bluetooth/btintel.h
> > +++ b/drivers/bluetooth/btintel.h
> > @@ -209,7 +209,7 @@ struct btintel_data {
> > #define btintel_wait_on_flag_timeout(hdev, nr, m, to) \
> > wait_on_bit_timeout(btintel_get_flag(hdev), (nr), m, to)
> >
> > -#if IS_ENABLED(CONFIG_BT_INTEL)
> > +#if IS_ENABLED(CONFIG_BT_INTEL) || IS_ENABLED(CONFIG_BT_INTEL_PCIE)
> >
> > int btintel_check_bdaddr(struct hci_dev *hdev);
> > int btintel_enter_mfg(struct hci_dev *hdev);
> > diff --git a/drivers/bluetooth/btintel_pcie.c b/drivers/bluetooth/btintel_pcie.c
> > new file mode 100644
> > index 000000000000..e6ce2304dc57
> > --- /dev/null
> > +++ b/drivers/bluetooth/btintel_pcie.c
> > @@ -0,0 +1,1317 @@
> > +// SPDX-License-Identifier: GPL-2.0-or-later
> > +/*
> > + * Intel Bluetooth PCIE driver
> > + *
> > + * Copyright (C) 2017 Intel Corporation. All rights reserved.
>
> The above shall probably be updated to 2024, also the All rights
> reserved don't actually fit well with GPL so please remove it.
>
> > + * This program is free software; you can redistribute it and/or
> > + * modify it under the terms of the GNU General Public License version
> > + * 2 as published by the Free Software Foundation.
> > + *
> > + * This program is distributed in the hope that it will be useful,
> > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> > + * GNU General Public License for more details.
> > + *
> > + * Copyright (C) 2022 Intel Corporation
>
> See above.
>
> > + * Intel Bluetooth Driver for PCIE interface.
> > + */
> > +#include <linux/kernel.h>
> > +#include <linux/module.h>
> > +#include <linux/firmware.h>
> > +#include <linux/pci.h>
> > +#include <linux/wait.h>
> > +#include <linux/delay.h>
> > +#include <linux/interrupt.h>
> > +
> > +#include <asm/unaligned.h>
> > +
> > +#include <net/bluetooth/bluetooth.h>
> > +#include <net/bluetooth/hci_core.h>
> > +
> > +#include "btintel.h"
> > +#include "btintel_pcie.h"
> > +
> > +#define VERSION "0.1"
> > +
> > +#define BTINTEL_PCI_DEVICE(dev, subdev) \
> > + .vendor = PCI_VENDOR_ID_INTEL, \
> > + .device = (dev), \
> > + .subvendor = PCI_ANY_ID, \
> > + .subdevice = (subdev), \
> > + .driver_data = 0
> > +
> > +/* Intel Bluetooth PCIe device id table */
> > +static const struct pci_device_id btintel_pcie_table[] = {
> > + { BTINTEL_PCI_DEVICE(0xA876, PCI_ANY_ID) },
> > + { 0 }
> > +};
> > +MODULE_DEVICE_TABLE(pci, btintel_pcie_table);
> > +
> > +/* Intel PCIe uses 4 bytes of HCI type instead of 1 byte BT SIG HCI type */
> > +#define BTINTEL_PCIE_HCI_TYPE_LEN 4
> > +#define BTINTEL_PCIE_HCI_CMD_PKT 0x00000001
> > +#define BTINTEL_PCIE_HCI_ACL_PKT 0x00000002
> > +#define BTINTEL_PCIE_HCI_SCO_PKT 0x00000003
> > +#define BTINTEL_PCIE_HCI_EVT_PKT 0x00000004
> > +
> > +#define BTITNEL_PCIE_ENABLE_HCI_DUMP 0
> > +
> > +#if BTITNEL_PCIE_ENABLE_HCI_DUMP
> > +static inline void btintel_pcie_hci_dump(const char *p, const void *b, int s)
> > +{
> > + const unsigned char *ptr = (const unsigned char *)b;
> > + char str[64];
> > + int c, i;
> > +
> > + for (i = c = 0; c < s; c++) {
> > + i += snprintf(str + i, sizeof(str) - i, "%02x ", ptr[c]);
> > + if ((c > 0 && (c + 1) % 8 == 0) || (c == s - 1)) {
> > + BT_DBG("%s: %s", p, str);
> > + i = 0;
> > + }
> > + }
> > +}
> > +#else
> > +static inline void btintel_pcie_hci_dump(const char *p, const void *b, int s)
> > +{
> > +}
> > +#endif
>
> We have the monitor to process HCI traffic, not really sure what is
> the purpose with the functions above.
>
> > +static void ipc_print_ia_ring(struct ia *ia, u16 queue_num)
> > +{
> > + BT_DBG("[%s] ---------------- ia ----------------",
> > + queue_num == TXQ_NUM ? "TXQ" : "RXQ");
> > + BT_DBG("[%s] tr-h:%02u tr-t:%02u cr-h:%02u cr-t:%02u",
> > + queue_num == TXQ_NUM ? "TXQ" : "RXQ",
> > + ia->tr_hia[queue_num], ia->tr_tia[queue_num],
> > + ia->cr_hia[queue_num], ia->cr_tia[queue_num]);
> > +}
> > +
> > +static void ipc_print_urbd0(struct urbd0 *urbd0, u16 index)
> > +{
> > + BT_DBG("[TXQ] -------------- urbd0[%u] --------------", index);
> > + BT_DBG("[TXQ] tfd_index:%u num_txq:%u cmpl_cnt:%u immediate_cmpl:0x%x",
> > + urbd0->tfd_index, urbd0->num_txq, urbd0->cmpl_count,
> > + urbd0->immediate_cmpl);
> > +}
> > +
> > +static void ipc_print_frbd(struct frbd *frbd, u16 index)
> > +{
> > + BT_DBG("[RXQ] -------------- frbd[%u] --------------", index);
> > + BT_DBG("[RXQ] tag:%u addr:0x%llx", frbd->tag, frbd->addr);
> > +}
> > +
> > +static void ipc_print_urbd1(struct urbd1 *urbd1, u16 index)
> > +{
> > + BT_DBG("[RXQ] -------------- urbd1[%u] --------------", index);
> > + BT_DBG("[RXQ] frbd_tag:%u status: 0x%x fixed:0x%x",
> > + urbd1->frbd_tag, urbd1->status, urbd1->fixed);
> > +}
>
> We need to replace usage of BT_DBG with bt_dev_dbg, etc.
>
> > +/* Poll internal in microseconds */
> > +#define POLL_INTERVAL 10
> > +
> > +static int btintel_pcie_poll_bit(struct btintel_pcie_data *data, u32 offset,
> > + u32 bits, u32 mask, int timeout)
> > +{
> > + int t = 0;
> > + u32 reg;
> > +
> > + BT_DBG("Enter poll_bit");
> > + do {
> > + reg = btintel_pcie_rd_reg32(data, offset);
> > + BT_DBG("CURRENT FUNC_CTRL_REG: 0x%x", reg);
> > +
> > + if ((reg & mask) == (bits & mask)) {
> > + BT_DBG("Poll bit matched");
> > + return t;
> > + }
> > + udelay(POLL_INTERVAL);
> > + t += POLL_INTERVAL;
> > + BT_DBG("Poll wait: %d", t);
> > + } while (t < timeout);
>
> Way too much debugging for such a trivial function, I'd actually
> remove all calls to BT_DBG here.
>
> > + return -ETIMEDOUT;
> > +}
> > +
> > +static struct btintel_pcie_data *btintel_pcie_get_data(struct msix_entry *entry)
> > +{
> > + u8 queue = entry->entry;
> > + struct msix_entry *entries = entry - queue;
> > +
> > + return container_of(entries, struct btintel_pcie_data, msix_entries[0]);
> > +}
> > +
> > +/* Set the doorbell for RXQ to notify the device that @index(actually index-1)
> > + * is available to receive the data
> > + */
> > +static void btintel_pcie_set_rx_db(struct btintel_pcie_data *data, u16 index)
> > +{
> > + u32 val;
> > +
> > + val = index;
> > + val |= (513 << 16);
> > +
> > + BT_DBG("[RXQ] Set doorbell for index: %u", index);
> > + btintel_pcie_wr_reg32(data, CSR_HBUS_TARG_WRPTR, val);
> > +}
> > +
> > +/* Update the FRBD(free buffer descriptor) with the @frbd_index and the
> > + * DMA address of the free buffer.
> > + */
> > +static void btintel_pcie_prepare_rx(struct rxq *rxq, u16 frbd_index)
> > +{
> > + struct data_buf *buf;
> > + struct frbd *frbd;
> > +
> > + /* Get the buffer of the frbd for DMA */
> > + buf = &rxq->bufs[frbd_index];
> > +
> > + frbd = &rxq->frbds[frbd_index];
> > + memset(frbd, 0, sizeof(*frbd));
> > +
> > + /* Update FRBD */
> > + frbd->tag = frbd_index;
> > + frbd->addr = buf->data_p_addr;
> > + ipc_print_frbd(frbd, frbd_index);
> > +}
> > +
> > +static int btintel_pcie_submit_rx(struct btintel_pcie_data *data)
> > +{
> > + u16 frbd_index;
> > + struct rxq *rxq = &data->rxq;
> > +
> > + /* Read the frbd index from the TR_HIA(Head Index Array) for RXQ */
> > + frbd_index = data->ia.tr_hia[RXQ_NUM];
> > + BT_DBG("[RXQ] current frbd_index: %u", frbd_index);
> > +
> > + /* Make sure the index value is within the range. It shouldn't be
> > + * bigger than the total count of the queue.
> > + */
> > + if (frbd_index > rxq->count) {
> > + BT_ERR("[RXQ] RXQ out of range: (0x%x)", frbd_index);
> > + return -ERANGE;
> > + }
> > +
> > + /* Prepare for RX submit. It updates the FRBD with the address of DMA
> > + * buffer
> > + */
> > + btintel_pcie_prepare_rx(rxq, frbd_index);
> > +
> > + /* Update TR_HIA with new FRBD index */
> > + frbd_index = (frbd_index + 1) % rxq->count;
> > + data->ia.tr_hia[RXQ_NUM] = frbd_index;
> > + ipc_print_ia_ring(&data->ia, RXQ_NUM);
> > +
> > + /* Set the doorbell to notify the device */
> > + btintel_pcie_set_rx_db(data, frbd_index);
> > +
> > + BT_DBG("[RXQ] rx sumbit completed");
> > +
> > + return 0;
> > +}
> > +
> > +static int btintel_pcie_start_rx(struct btintel_pcie_data *data)
> > +{
> > + int i, ret;
> > +
> > + for (i = 0; i < RX_MAX_QUEUE; i++) {
> > + ret = btintel_pcie_submit_rx(data);
> > + if (ret) {
> > + BT_ERR("[RXQ] failed to submit frbd(%d)", ret);
> > + return ret;
> > + }
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static void btintel_pcie_reset_ia(struct btintel_pcie_data *data)
> > +{
> > + memset(data->ia.tr_hia, 0, sizeof(u16) * NUM_QUEUES);
> > + memset(data->ia.tr_tia, 0, sizeof(u16) * NUM_QUEUES);
> > + memset(data->ia.cr_hia, 0, sizeof(u16) * NUM_QUEUES);
> > + memset(data->ia.cr_tia, 0, sizeof(u16) * NUM_QUEUES);
> > + BT_DBG("Index Arrays are reset");
> > +}
> > +
> > +static void btintel_pcie_reset_bt(struct btintel_pcie_data *data)
> > +{
> > + BT_INFO("Reset BT Function ");
> > + btintel_pcie_wr_reg32(data, CSR_FUNC_CTRL_REG, CSR_FUNC_CTRL_SW_RESET);
> > +}
> > +
> > +/* This function enables BT function by setting CSR_FUNC_CTRL_MAC_INIT bit in
> > + * CSR_FUNC_CTRL_REG register and wait for MSI-X with MSIX_HW_INT_CAUSES_GP0.
> > + * Then the host reads firmware version from CSR_F2D_MBX and the boot stage
> > + * from CSR_BOOT_STAGE_REG.
> > + */
> > +static int btintel_pcie_enable_bt(struct btintel_pcie_data *data)
> > +{
> > + int err;
> > + u32 reg;
> > +
> > + data->gp0_received = false;
> > +
> > + /* Update the DMA address of CI struct to CSR */
> > + btintel_pcie_wr_reg32(data, CSR_CI_ADDR_LSB_REG,
> > + data->ci_p_addr & 0xffffffff);
> > + btintel_pcie_wr_reg32(data, CSR_CI_ADDR_MSB_REG,
> > + data->ci_p_addr >> 32);
> > +
> > + /* Reset the cached value of boot stage. it is updated by the msix
> > + * gp0 interrupt handler.
> > + */
> > + data->boot_stage_cache = 0x0;
> > +
> > + /* Set MAC_INIT bit to start primary bootloader */
> > + reg = btintel_pcie_rd_reg32(data, CSR_FUNC_CTRL_REG);
> > + BT_INFO("Before: FUNC_CTRL_REG: 0x%x", reg);
> > +
> > + btintel_pcie_set_reg_bits(data, CSR_FUNC_CTRL_REG,
> > + CSR_FUNC_CTRL_MAC_INIT);
> > + BT_INFO("MAC_INIT is set");
>
> It is useless to printing this sort of information, let alone using BT_INFO...
>
> > + /* Wait until MAC_ACCESS is granted */
> > + err = btintel_pcie_poll_bit(data, CSR_FUNC_CTRL_REG,
> > + CSR_FUNC_CTRL_MAC_ACCESS_STS,
> > + CSR_FUNC_CTRL_MAC_ACCESS_STS,
> > + DEFAULT_MAC_ACCESS_TIMEOUT);
> > + if (err < 0) {
> > + BT_ERR("Failed to start bootloader even after %u ns",
> > + DEFAULT_MAC_ACCESS_TIMEOUT);
> > + return -ENODEV;
> > + }
> > +
> > + /* MAC is ready. Enable BT FUNC */
> > + btintel_pcie_set_reg_bits(data, CSR_FUNC_CTRL_REG,
> > + CSR_FUNC_CTRL_FUNC_ENA |
> > + CSR_FUNC_CTRL_FUNC_INIT);
> > +
> > + reg = btintel_pcie_rd_reg32(data, CSR_FUNC_CTRL_REG);
> > + BT_INFO("After: FUNC_CTRL_REG: 0x%x", reg);
>
> Ditto.
>
> > + /* wait for interrupt from the device after booting up to primary
> > + * bootloader.
> > + */
> > + err = wait_event_timeout(data->gp0_wait_q, data->gp0_received,
> > + msecs_to_jiffies(DEFAULT_INTR_TIMEOUT));
> > + if (!err) {
> > + BT_ERR("Failed to receive mac_init interrupt");
> > + return -ETIME;
> > + }
> > +
> > + /* Check cached boot stage is CSR_BOOT_STAGE_ROM(BIT(0)) */
> > + if (~data->boot_stage_cache & CSR_BOOT_STAGE_ROM) {
> > + BT_ERR("Device is not running in rom");
> > + return -ENODEV;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +/* This function handles the MSI-X interrupt for gp0 cause(bit 0 in
> > + * CSR_MSIX_HW_INT_CAUSES) which is sent for boot stage and image response.
> > + */
> > +static void btintel_pcie_msix_gp0_handler(struct btintel_pcie_data *data)
> > +{
> > + u32 reg;
> > +
> > + /* This interrupt is for three different causes and it is not easy to
> > + * know what causes the interrupt. So, it compares each register value
> > + * with cached value and update it before it wake up the queue.
> > + */
> > + reg = btintel_pcie_rd_reg32(data, CSR_BOOT_STAGE_REG);
> > + if (reg != data->boot_stage_cache) {
> > + data->boot_stage_cache = reg;
> > +
> > + BT_DBG("Boot Stage updated: 0x%x", reg);
> > + }
> > +
> > + reg = btintel_pcie_rd_reg32(data, CSR_IMG_RESPONSE_REG);
> > + if (reg != data->img_resp_cache) {
> > + data->img_resp_cache = reg;
> > +
> > + BT_DBG("Image Response updated: 0x%x", reg);
> > + }
> > +
> > + BT_DBG("---------- cached GP0 registers ----------");
> > + BT_DBG("Cached Boot Stage Reg: 0x%x", data->boot_stage_cache);
> > + BT_DBG("Cached Image Resp Reg: 0x%x", data->img_resp_cache);
> > +
> > + data->gp0_received = true;
> > +
> > + /* If the boot stage is OP or IML, reset IA and start RX again */
> > + if (data->boot_stage_cache & CSR_BOOT_STAGE_OPFW ||
> > + data->boot_stage_cache & CSR_BOOT_STAGE_IML) {
> > + btintel_pcie_reset_ia(data);
> > + btintel_pcie_start_rx(data);
> > + }
> > +
> > + wake_up(&data->gp0_wait_q);
> > +}
> > +
> > +/* This function handles the MSX-X interrupt for rx queue 0 which is for TX
> > + */
> > +static void btintel_pcie_msix_tx_handle(struct btintel_pcie_data *data)
> > +{
> > + u16 cr_tia, cr_hia;
> > + struct txq *txq;
> > + struct urbd0 *urbd0;
> > +
> > + cr_tia = data->ia.cr_tia[TXQ_NUM];
> > + cr_hia = data->ia.cr_hia[TXQ_NUM];
> > +
> > + BT_DBG("[TXQ] cr_hia=%u cr_tia=%u", cr_hia, cr_tia);
> > +
> > + /* Check CR_TIA and CR_HIA for change */
> > + if (cr_tia == cr_hia) {
> > + BT_ERR("[TXQ] no new CD found");
> > + return;
> > + }
> > +
> > + txq = &data->txq;
> > +
> > + while (cr_tia != cr_hia) {
> > + BT_DBG("[TXQ] wake up tx_wait_q");
> > +
> > + data->tx_wait_done = true;
> > + wake_up(&data->tx_wait_q);
> > +
> > + /* Get URBD0 pointed by cr_tia */
> > + urbd0 = &txq->urbd0s[cr_tia];
> > + ipc_print_urbd0(urbd0, cr_tia);
> > +
> > + /* Make sure the completed TFD index is within the range */
> > + if (urbd0->tfd_index > txq->count) {
> > + BT_ERR("[TXQ] out of range: (0x%x)", urbd0->tfd_index);
> > + return;
> > + }
> > +
> > + /* Increase cr_tia */
> > + cr_tia = (cr_tia + 1) % txq->count;
> > + data->ia.cr_tia[TXQ_NUM] = cr_tia;
> > + ipc_print_ia_ring(&data->ia, TXQ_NUM);
> > + }
> > +}
> > +
> > +static int btintel_pcie_recv_event_intel(struct hci_dev *hdev,
> > + struct sk_buff *skb)
> > +{
> > + if (btintel_test_flag(hdev, INTEL_BOOTLOADER)) {
> > + struct hci_event_hdr *hdr = (void *)skb->data;
> > +
> > + if (skb->len > HCI_EVENT_HDR_SIZE && hdr->evt == 0xff &&
> > + hdr->plen > 0) {
> > + const void *ptr = skb->data + HCI_EVENT_HDR_SIZE + 1;
> > + unsigned int len = skb->len - HCI_EVENT_HDR_SIZE - 1;
> > +
> > + switch (skb->data[2]) {
> > + case 0x02:
> > + /* When switching to the operational firmware
> > + * the device sends a vendor specific event
> > + * indicating that the bootup completed.
> > + */
> > + btintel_bootup(hdev, ptr, len);
> > + break;
> > + case 0x06:
> > + /* When the firmware loading completes the
> > + * device sends out a vendor specific event
> > + * indicating the result of the firmware
> > + * loading.
> > + */
> > + btintel_secure_send_result(hdev, ptr, len);
> > + break;
> > + }
> > + }
> > + }
> > +
> > + return hci_recv_frame(hdev, skb);
> > +}
>
> Replace the above with btintel_recv_event?
>
> > +/* Process the received rx data
> > + * It check the frame header to identify the data type and create skb
> > + * and calling HCI API
> > + */
> > +static int btintel_pcie_hci_recv_frame(struct btintel_pcie_data *data,
> > + void *buf, int count)
> > +{
> > + struct hci_dev *hdev = data->hdev;
> > + int ret;
> > + u32 pkt_type;
> > + u16 plen;
> > + struct sk_buff *skb;
> > +
> > + spin_lock(&data->hci_rx_lock);
> > +
> > + /* The first 4 bytes indicates the Intel PCIe specific packet type.
> > + * Read the packet type here before remove it.
> > + */
> > + pkt_type = get_unaligned_le32(buf);
> > + bt_dev_dbg(hdev, "pkt_type=%u count=%d", pkt_type, count);
> > +
> > + buf += BTINTEL_PCIE_HCI_TYPE_LEN;
> > + count -= BTINTEL_PCIE_HCI_TYPE_LEN;
> > +
> > + hdev->stat.byte_rx += count;
> > +
> > + skb = bt_skb_alloc(count, GFP_ATOMIC);
> > + if (!skb) {
> > + bt_dev_err(hdev, "Failed to allocate skb for event");
> > + ret = -ENOMEM;
> > + goto exit_error;
> > + }
> > +
> > + switch (pkt_type) {
> > + case BTINTEL_PCIE_HCI_ACL_PKT:
> > + hci_skb_pkt_type(skb) = HCI_ACLDATA_PKT;
> > + memcpy(skb_put(skb, HCI_ACL_HDR_SIZE), buf, HCI_ACL_HDR_SIZE);
> > + plen = hci_acl_hdr(skb)->dlen;
> > + buf += HCI_ACL_HDR_SIZE;
> > + break;
> > + case BTINTEL_PCIE_HCI_SCO_PKT:
> > + hci_skb_pkt_type(skb) = HCI_SCODATA_PKT;
> > + memcpy(skb_put(skb, HCI_SCO_HDR_SIZE), buf, HCI_SCO_HDR_SIZE);
> > + plen = hci_sco_hdr(skb)->dlen;
> > + buf += HCI_SCO_HDR_SIZE;
> > + break;
> > + case BTINTEL_PCIE_HCI_EVT_PKT:
> > + hci_skb_pkt_type(skb) = HCI_EVENT_PKT;
> > + memcpy(skb_put(skb, HCI_EVENT_HDR_SIZE), buf,
> > + HCI_EVENT_HDR_SIZE);
> > + plen = hci_event_hdr(skb)->plen;
> > + buf += HCI_EVENT_HDR_SIZE;
> > + break;
> > + default:
> > + ret = -EILSEQ;
> > + kfree_skb(skb);
> > + goto exit_error;
> > + }
> > + memcpy(skb_put(skb, plen), buf, plen);
>
> This is very unsafe, to say the least, since we are not checking if
> buf actually contains all the data since we never seem to use the
> count parameter.
>
> > +
> > + if (pkt_type == BTINTEL_PCIE_HCI_EVT_PKT)
> > + ret = btintel_pcie_recv_event_intel(hdev, skb);
> > + else
> > + ret = hci_recv_frame(hdev, skb);
> > +
> > +exit_error:
> > + if (ret)
> > + hdev->stat.err_rx++;
> > +
> > + spin_unlock(&data->hci_rx_lock);
> > +
> > + return ret;
> > +}
>
> Hmm, this doesn't sound quite right compared to the likes of
> h4_recv_buf, are we guaranteed to only receive complete packets for
> example?
>
> > +/* RX work queue */
> > +static void btintel_pcie_rx_work(struct work_struct *work)
> > +{
> > + struct btintel_pcie_data *data = container_of(work,
> > + struct btintel_pcie_data, rx_work);
> > + struct sk_buff *skb;
> > + int err;
> > +
> > + /* Process the sk_buf in queue and send to the hci layer */
> > + while ((skb = skb_dequeue(&data->rx_skb_q))) {
> > + err = btintel_pcie_hci_recv_frame(data, skb->data, skb->len);
>
> If the data comes as skb then pass the skb and not just the data, len,
> that way we can actually make use of things like skb_pull_data to
> advance in the buffer, etc.
>
> > + if (err) {
> > + BT_ERR("Failed to send received frame: %d", err);
> > + kfree_skb(skb);
> > + }
Missed this one, it appears we are leaking the skb if err = 0.
> > + }
> > +}
> > +
> > +/* create the sk_buff with data and save it to queue and start rx work
> > + */
> > +static int btintel_pcie_submit_rx_work(struct btintel_pcie_data *data, u8 status,
> > + void *buf)
> > +{
> > + int ret, len;
> > + struct rfh_hdr *rfh_hdr;
> > + struct sk_buff *skb;
> > +
> > + rfh_hdr = (struct rfh_hdr *)buf;
> > + btintel_pcie_hci_dump("RFH HDR", buf, sizeof(*rfh_hdr));
> > +
> > + len = rfh_hdr->packet_len;
> > +
> > + /* Remove RFH header */
> > + buf += sizeof(*rfh_hdr);
> > + btintel_pcie_hci_dump("RX", buf, len);
> > +
> > + /* Create the sk_buf with packet in the buf and save it to sk_buf queue
> > + */
> > + skb = alloc_skb(len, GFP_ATOMIC);
> > + if (!skb) {
> > + ret = -ENOMEM;
> > + goto resubmit;
> > + }
> > +
> > + /* Copy the data to skb */
> > + memcpy(skb_put(skb, len), buf, len);
> > +
> > + /* Save the skb to rx queue */
> > + skb_queue_tail(&data->rx_skb_q, skb);
> > +
> > + /* Calling rx_work queue to process the skb */
> > + queue_work(data->workqueue, &data->rx_work);
> > +
> > +resubmit:
> > + BT_DBG("submit next read request");
> > +
> > + /* submit read */
> > + ret = btintel_pcie_submit_rx(data);
> > +
> > + return ret;
> > +}
> > +
> > +/* This function handles the MSI-X interrupt for rx queue 1 which is for RX
> > + */
> > +static void btintel_pcie_msix_rx_handle(struct btintel_pcie_data *data)
> > +{
> > + u16 cr_hia, cr_tia;
> > + struct rxq *rxq;
> > + struct urbd1 *urbd1;
> > + struct frbd *frbd;
> > + struct data_buf *buf;
> > + int ret;
> > +
> > + cr_hia = data->ia.cr_hia[RXQ_NUM];
> > + cr_tia = data->ia.cr_tia[RXQ_NUM];
> > +
> > + BT_DBG("[RXQ] cr_hia=%u cr_tia=%u", cr_hia, cr_tia);
> > +
> > + /* Check CR_TIA and CR_HIA for change */
> > + if (cr_tia == cr_hia) {
> > + BT_ERR("[RXQ] no new CD found");
> > + return;
> > + }
> > +
> > + rxq = &data->rxq;
> > +
> > + /* The firmware sends multiple CD in a single MSIX and it needs to
> > + * process all received CDs in this interrupt.
> > + */
> > + while (cr_tia != cr_hia) {
> > + /* Get URBD1 pointed by cr_tia */
> > + urbd1 = &rxq->urbd1s[cr_tia];
> > + ipc_print_urbd1(urbd1, cr_tia);
> > +
> > + /* Get FRBD poined by urbd1->frbd_tag */
> > + frbd = &rxq->frbds[urbd1->frbd_tag];
> > +
> > + /* Get buf from FRBD tag */
> > + buf = &rxq->bufs[urbd1->frbd_tag];
> > + if (!buf) {
> > + BT_ERR("[RXQ] failed to get the DMA buffer for %d",
> > + urbd1->frbd_tag);
> > + return;
> > + }
> > +
> > + /* prepare RX work */
> > + ret = btintel_pcie_submit_rx_work(data, urbd1->status,
> > + buf->data);
> > + if (ret) {
> > + BT_ERR("[RXQ] failed to submit rx request");
> > + return;
> > + }
> > +
> > + /* Update cr_tia */
> > + cr_tia = (cr_tia + 1) % rxq->count;
> > + data->ia.cr_tia[RXQ_NUM] = cr_tia;
> > + ipc_print_ia_ring(&data->ia, RXQ_NUM);
> > + }
> > + BT_DBG("[RXQ] completed rx interrupt");
> > +}
> > +
> > +static irqreturn_t btintel_pcie_msix_isr(int irq, void *data)
> > +{
> > + return IRQ_WAKE_THREAD;
> > +}
> > +
> > +static irqreturn_t btintel_pcie_irq_msix_handler(int irq, void *dev_id)
> > +{
> > + struct msix_entry *entry = dev_id;
> > + struct btintel_pcie_data *data = btintel_pcie_get_data(entry);
> > + u32 intr_fh, intr_hw;
> > +
> > + BT_DBG("handling msix(irq=%d dev_id=0x%p)", irq, dev_id);
> > +
> > + spin_lock(&data->irq_lock);
> > + intr_fh = btintel_pcie_rd_reg32(data, CSR_MSIX_FH_INT_CAUSES);
> > + intr_hw = btintel_pcie_rd_reg32(data, CSR_MSIX_HW_INT_CAUSES);
> > +
> > + /* Clear causes registers to avoid being handling the same cause */
> > + btintel_pcie_wr_reg32(data, CSR_MSIX_FH_INT_CAUSES, intr_fh);
> > + btintel_pcie_wr_reg32(data, CSR_MSIX_HW_INT_CAUSES, intr_hw);
> > + spin_unlock(&data->irq_lock);
> > +
> > + BT_DBG("intr_fh=0x%x intr_hw=0x%x", intr_fh, intr_hw);
> > +
> > + if (unlikely(!(intr_fh | intr_hw))) {
> > + BT_DBG("Ignore interrupt, inta == 0");
> > + return IRQ_NONE;
> > + }
> > +
> > + /* This interrupt is triggered by the firmware after updating
> > + * boot_stage register and image_response register
> > + */
> > + if (intr_hw & MSIX_HW_INT_CAUSES_GP0) {
> > + BT_DBG("intr for MSIX_HW_INT_CAUSES_GP0");
> > + btintel_pcie_msix_gp0_handler(data);
> > + }
> > +
> > + /* For TX */
> > + if (intr_fh & MSIX_FH_INT_CAUSES_0) {
> > + BT_DBG("intr for MSIX_FH_INT_CAUSES_0");
> > + btintel_pcie_msix_tx_handle(data);
> > + }
> > +
> > + /* For RX */
> > + if (intr_fh & MSIX_FH_INT_CAUSES_1) {
> > + BT_DBG("intr for MSIX_FH_INT_CAUSES_1");
> > + btintel_pcie_msix_rx_handle(data);
> > + }
> > +
> > + /* TODO: Add handler for other causes */
> > + /*
> > + * Before sending the interrupt the HW disables it to prevent
> > + * a nested interrupt. This is done by writing 1 to the corresponding
> > + * bit in the mask register. After handling the interrupt, it should be
> > + * re-enabled by clearing this bit. This register is defined as
> > + * write 1 clear (W1C) register, meaning that it's being clear
> > + * by writing 1 to the bit.
> > + */
> > + btintel_pcie_wr_reg32(data, CSR_MSIX_AUTOMASK_ST, BIT(entry->entry));
> > +
> > + return IRQ_HANDLED;
> > +}
> > +
> > +/* This function requests the irq for msix and registers the handlers per irq.
> > + * Currently, it requests only 1 irq for all interrupt causes.
> > + */
> > +static int btintel_pcie_setup_irq(struct btintel_pcie_data *data)
> > +{
> > + int err;
> > + int num_irqs, i;
> > +
> > + BT_DBG("Initialize msix_entries...");
> > + for (i = 0; i < MSIX_VEC_MAX; i++) {
> > + data->msix_entries[i].entry = i;
> > + BT_DBG("msix_entries[%d] vector=0x%x entry=0x%x",
> > + i, data->msix_entries[i].vector,
> > + data->msix_entries[i].entry);
> > + }
> > +
> > + num_irqs = pci_enable_msix_range(data->pdev, data->msix_entries,
> > + MSIX_VEC_MIN,
> > + MSIX_VEC_MAX);
> > + if (num_irqs < 0) {
> > + BT_ERR("Failed to enable msix range (%d)", num_irqs);
> > + return num_irqs;
> > + }
> > +
> > + data->alloc_vecs = num_irqs;
> > + data->msix_enabled = 1;
> > + data->def_irq = 0;
> > +
> > + BT_DBG("Returned num_irqs=%d", num_irqs);
> > + for (i = 0; i < num_irqs; i++) {
> > + BT_DBG("msix_entries[%d] vector=0x%x entry=0x%x", i,
> > + data->msix_entries[i].vector,
> > + data->msix_entries[i].entry);
> > + }
> > +
> > + BT_DBG("setup irq handler");
> > + for (i = 0; i < data->alloc_vecs; i++) {
> > + struct msix_entry *msix_entry;
> > +
> > + msix_entry = &data->msix_entries[i];
> > +
> > + err = devm_request_threaded_irq(&data->pdev->dev,
> > + msix_entry->vector,
> > + btintel_pcie_msix_isr,
> > + btintel_pcie_irq_msix_handler,
> > + IRQF_SHARED,
> > + KBUILD_MODNAME,
> > + msix_entry);
> > + if (err) {
> > + BT_ERR("Failed to allocate irq handler (%d)", err);
> > + return err;
> > + }
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +struct btintel_pcie_causes_list {
> > + u32 cause;
> > + u32 mask_reg;
> > + u8 cause_num;
> > +};
> > +
> > +struct btintel_pcie_causes_list causes_list[] = {
> > + { MSIX_FH_INT_CAUSES_0, CSR_MSIX_FH_INT_MASK, 0x00 },
> > + { MSIX_FH_INT_CAUSES_1, CSR_MSIX_FH_INT_MASK, 0x01 },
> > + { MSIX_HW_INT_CAUSES_GP0, CSR_MSIX_HW_INT_MASK, 0x20 },
> > +};
> > +
> > +/* This function configures the interrupt masks for both HW_INT_CAUSES and
> > + * FH_INT_CAUSES which are meaningful to us.
> > + *
> > + * After resetting BT function via PCIE FLR or FUNC_CTRL reset, the driver
> > + * need to call this function again to configure it again since the masks
> > + * are reset to 0xFFFFFFFF after reset.
> > + */
> > +static void btintel_pcie_config_msix(struct btintel_pcie_data *data)
> > +{
> > + int i;
> > + int val = data->def_irq | MSIX_NON_AUTO_CLEAR_CAUSE;
> > +
> > + /* Set Non Auto Clear Cause */
> > + for (i = 0; i < ARRAY_SIZE(causes_list); i++) {
> > + btintel_pcie_wr_reg8(data,
> > + CSR_MSIX_IVAR(causes_list[i].cause_num),
> > + val);
> > + btintel_pcie_clr_reg_bits(data,
> > + causes_list[i].mask_reg,
> > + causes_list[i].cause);
> > + }
> > +
> > + /* Save the initial interrupt mask */
> > + data->fh_init_mask = ~btintel_pcie_rd_reg32(data, CSR_MSIX_FH_INT_MASK);
> > + data->hw_init_mask = ~btintel_pcie_rd_reg32(data, CSR_MSIX_HW_INT_MASK);
> > + BT_DBG("init_mask: fh=0x%x hw=0x%x", data->fh_init_mask,
> > + data->hw_init_mask);
> > +}
> > +
> > +static int btintel_pcie_config_pcie(struct pci_dev *pdev,
> > + struct btintel_pcie_data *data)
> > +{
> > + int err;
> > +
> > + err = pcim_enable_device(pdev);
> > + if (err) {
> > + BT_ERR("Failed to enable pci device (%d)", err);
> > + return err;
> > + }
> > + pci_set_master(pdev);
> > +
> > + /* Setup DMA mask */
> > + BT_DBG("Set DMA_MASK(64)");
> > + err = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64));
> > + if (err) {
> > + BT_DBG("Set DMA_MASK(32)");
> > + err = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32));
> > + /* Both attempt failed */
> > + if (err) {
> > + BT_ERR("No suitable DMA available");
> > + return err;
> > + }
> > + }
> > +
> > + /* Get BAR to access CSR */
> > + err = pcim_iomap_regions(pdev, BIT(0), KBUILD_MODNAME);
> > + if (err) {
> > + BT_ERR("Failed to get iomap regions (%d)", err);
> > + return err;
> > + }
> > +
> > + data->base_addr = pcim_iomap_table(pdev)[0];
> > + if (!data->base_addr) {
> > + BT_ERR("Failed to get base address");
> > + return -ENODEV;
> > + }
> > +
> > + err = btintel_pcie_setup_irq(data);
> > + if (err) {
> > + BT_ERR("Failed to setup irq for msix");
> > + return err;
> > + }
> > +
> > + /* Configure MSI-X with causes list */
> > + btintel_pcie_config_msix(data);
> > +
> > + return 0;
> > +}
> > +
> > +static void btintel_pcie_init_ci(struct btintel_pcie_data *data,
> > + struct ctx_info *ci)
> > +{
> > + ci->version = 0x1;
> > + ci->size = sizeof(*ci);
> > + ci->config = 0x0000;
> > + ci->addr_cr_hia = data->ia.cr_hia_p_addr;
> > + ci->addr_tr_tia = data->ia.tr_tia_p_addr;
> > + ci->addr_cr_tia = data->ia.cr_tia_p_addr;
> > + ci->addr_tr_hia = data->ia.tr_hia_p_addr;
> > + ci->num_cr_ia = NUM_QUEUES;
> > + ci->num_tr_ia = NUM_QUEUES;
> > + ci->addr_urbdq0 = data->txq.urbd0s_p_addr;
> > + ci->addr_tfdq = data->txq.tfds_p_addr;
> > + ci->num_tfdq = data->txq.count;
> > + ci->num_urbdq0 = data->txq.count;
> > + ci->tfdq_db_vec = TXQ_NUM;
> > + ci->urbdq0_db_vec = TXQ_NUM;
> > + ci->rbd_size = RBD_SIZE_4K;
> > + ci->addr_frbdq = data->rxq.frbds_p_addr;
> > + ci->num_frbdq = data->rxq.count;
> > + ci->frbdq_db_vec = RXQ_NUM;
> > + ci->addr_urbdq1 = data->rxq.urbd1s_p_addr;
> > + ci->num_urbdq1 = data->rxq.count;
> > + ci->urbdq_db_vec = RXQ_NUM;
> > +}
> > +
> > +static void btintel_pcie_free_txq_bufs(struct btintel_pcie_data *data,
> > + struct txq *txq)
> > +{
> > + /* Free data buffers first */
> > + dma_free_coherent(&data->pdev->dev, txq->count * BUFFER_SIZE,
> > + txq->buf_v_addr, txq->buf_p_addr);
> > + kfree(txq->bufs);
> > + BT_DBG("txq buffers are freed");
> > +}
> > +
> > +static int btintel_pcie_setup_txq_bufs(struct btintel_pcie_data *data,
> > + struct txq *txq)
> > +{
> > + int err = 0, i;
> > + struct data_buf *buf;
> > +
> > + if (txq->count == 0) {
> > + BT_ERR("invalid parameter: txq->count");
> > + err = -EINVAL;
> > + goto exit_error;
> > + }
> > +
> > + /* Allocate the same number of buffers as the descriptor */
> > + txq->bufs = kmalloc_array(txq->count, sizeof(*buf), GFP_KERNEL);
> > + if (!txq->bufs) {
> > + err = -ENOMEM;
> > + goto exit_error;
> > + }
> > +
> > + /* Allocate full chunk of data buffer for DMA first and do indexing and
> > + * initialization next, so it can be freed easily
> > + */
> > + txq->buf_v_addr = dma_alloc_coherent(&data->pdev->dev,
> > + txq->count * BUFFER_SIZE,
> > + &txq->buf_p_addr,
> > + GFP_KERNEL | __GFP_NOWARN);
> > + if (!txq->buf_v_addr) {
> > + BT_ERR("Failed to allocate DMA buf");
> > + err = -ENOMEM;
> > + kfree(txq->bufs);
> > + goto exit_error;
> > + }
> > + memset(txq->buf_v_addr, 0, txq->count * BUFFER_SIZE);
> > +
> > + BT_DBG("alloc bufs: p=0x%llx v=0x%p", txq->buf_p_addr, txq->buf_v_addr);
> > +
> > + /* Setup the allocated DMA buffer to bufs. Each data_buf should
> > + * have virtual address and physical address
> > + */
> > + for (i = 0; i < txq->count; i++) {
> > + buf = &txq->bufs[i];
> > + buf->data_p_addr = txq->buf_p_addr + (i * BUFFER_SIZE);
> > + buf->data = txq->buf_v_addr + (i * BUFFER_SIZE);
> > + }
> > +
> > +exit_error:
> > + return err;
> > +}
> > +
> > +static void btintel_pcie_free_rxq_bufs(struct btintel_pcie_data *data,
> > + struct rxq *rxq)
> > +{
> > + /* Free data buffers first */
> > + dma_free_coherent(&data->pdev->dev, rxq->count * BUFFER_SIZE,
> > + rxq->buf_v_addr, rxq->buf_p_addr);
> > + kfree(rxq->bufs);
> > + BT_DBG("rxq buffers are freed");
> > +}
> > +
> > +static int btintel_pcie_setup_rxq_bufs(struct btintel_pcie_data *data,
> > + struct rxq *rxq)
> > +{
> > + int err = 0, i;
> > + struct data_buf *buf;
> > +
> > + if (rxq->count == 0) {
> > + BT_ERR("invalid parameter: rxq->count");
> > + err = -EINVAL;
> > + goto exit_error;
> > + }
> > +
> > + /* Allocate the same number of buffers as the descriptor */
> > + rxq->bufs = kmalloc_array(rxq->count, sizeof(*buf), GFP_KERNEL);
> > + if (!rxq->bufs) {
> > + err = -ENOMEM;
> > + goto exit_error;
> > + }
> > +
> > + /* Allocate full chunk of data buffer for DMA first and do indexing and
> > + * initialization next, so it can be freed easily
> > + */
> > + rxq->buf_v_addr = dma_alloc_coherent(&data->pdev->dev,
> > + rxq->count * BUFFER_SIZE,
> > + &rxq->buf_p_addr,
> > + GFP_KERNEL | __GFP_NOWARN);
> > + if (!rxq->buf_v_addr) {
> > + BT_ERR("Failed to allocate DMA buf");
> > + err = -ENOMEM;
> > + kfree(rxq->bufs);
> > + goto exit_error;
> > + }
> > + memset(rxq->buf_v_addr, 0, rxq->count * BUFFER_SIZE);
> > +
> > + BT_DBG("alloc bufs: p=0x%llx v=0x%p", rxq->buf_p_addr, rxq->buf_v_addr);
> > +
> > + /* Setup the allocated DMA buffer to bufs. Each data_buf should
> > + * have virtual address and physical address
> > + */
> > + for (i = 0; i < rxq->count; i++) {
> > + buf = &rxq->bufs[i];
> > + buf->data_p_addr = rxq->buf_p_addr + (i * BUFFER_SIZE);
> > + buf->data = rxq->buf_v_addr + (i * BUFFER_SIZE);
> > + }
> > +
> > +exit_error:
> > +
> > + return err;
> > +}
> > +
> > +static void btintel_pcie_setup_ia(struct btintel_pcie_data *data,
> > + dma_addr_t p_addr, void *v_addr,
> > + struct ia *ia)
> > +{
> > + /* TR Head Index Array */
> > + ia->tr_hia_p_addr = p_addr;
> > + ia->tr_hia = v_addr;
> > +
> > + /* TR Tail Index Array */
> > + ia->tr_tia_p_addr = p_addr + sizeof(u16) * NUM_QUEUES;
> > + ia->tr_tia = v_addr + sizeof(u16) * NUM_QUEUES;
> > +
> > + /* CR Head index Array */
> > + ia->cr_hia_p_addr = p_addr + (sizeof(u16) * NUM_QUEUES * 2);
> > + ia->cr_hia = v_addr + (sizeof(u16) * NUM_QUEUES * 2);
> > +
> > + /* CR Tail Index Array */
> > + ia->cr_tia_p_addr = p_addr + (sizeof(u16) * NUM_QUEUES * 3);
> > + ia->cr_tia = v_addr + (sizeof(u16) * NUM_QUEUES * 3);
> > +}
> > +
> > +static void btintel_pcie_free(struct btintel_pcie_data *data)
> > +{
> > + btintel_pcie_free_rxq_bufs(data, &data->rxq);
> > + btintel_pcie_free_txq_bufs(data, &data->txq);
> > +
> > + dma_pool_free(data->dma_pool, data->dma_v_addr, data->dma_p_addr);
> > + dma_pool_destroy(data->dma_pool);
> > + BT_DBG("DMA memory is freed");
>
> Printing this kind of information is useless, we should really make
> sure there are no leaks but there are better tools for that then
> printing when we free data.
>
> > +}
> > +
> > +/* Allocate tx and rx queues, any related data structures and buffers.
> > + */
> > +static int btintel_pcie_alloc(struct btintel_pcie_data *data)
> > +{
> > + int err = 0;
> > + size_t total;
> > + dma_addr_t p_addr;
> > + void *v_addr;
> > +
> > + /* Allocate the chunk of DMA memory for descriptors, index array, and
> > + * context information, instead of allocating individually.
> > + * The DMA memory for data buffer is allocated while setting up the
> > + * each queue.
> > + *
> > + * Total size is sum of the following
> > + * + size of TFD * Number of descriptors in queue
> > + * + size of URBD0 * Number of descriptors in queue
> > + * + size of FRBD * Number of descriptors in queue
> > + * + size of URBD1 * Number of descriptors in queue
> > + * + size of index * Number of queues(2) * type of index array(4)
> > + * + size of context information
> > + */
> > + total = (sizeof(struct tfd) + sizeof(struct urbd0) + sizeof(struct frbd)
> > + + sizeof(struct urbd1)) * DESCS_COUNT;
> > +
> > + /* Add the sum of size of index array and size of ci struct */
> > + total += (sizeof(u16) * NUM_QUEUES * 4) + sizeof(struct ctx_info);
> > +
> > + /* Allocate DMA Pool */
> > + data->dma_pool = dma_pool_create(KBUILD_MODNAME, &data->pdev->dev,
> > + total, DMA_POOL_ALIGNMENT, 0);
> > + if (!data->dma_pool) {
> > + BT_ERR("Failed to allocate dma pool for queues");
> > + err = -ENOMEM;
> > + goto exit_error;
> > + }
> > +
> > + v_addr = dma_pool_zalloc(data->dma_pool, GFP_KERNEL | __GFP_NOWARN,
> > + &p_addr);
> > + if (!v_addr) {
> > + BT_ERR("Failed to alloc dma memory for queues");
> > + dma_pool_destroy(data->dma_pool);
> > + err = -ENOMEM;
> > + goto exit_error;
> > + }
> > +
> > + data->dma_p_addr = p_addr;
> > + data->dma_v_addr = v_addr;
> > +
> > + BT_DBG("dma pool: p_addr=0x%llx v_addr=0x%p", p_addr, v_addr);
> > +
> > + /* Setup descriptor count */
> > + data->txq.count = DESCS_COUNT;
> > + data->rxq.count = DESCS_COUNT;
> > +
> > + /* Setup tfds */
> > + data->txq.tfds_p_addr = p_addr;
> > + data->txq.tfds = v_addr;
> > +
> > + p_addr += (sizeof(struct tfd) * DESCS_COUNT);
> > + v_addr += (sizeof(struct tfd) * DESCS_COUNT);
> > +
> > + /* Setup urbd0 */
> > + data->txq.urbd0s_p_addr = p_addr;
> > + data->txq.urbd0s = v_addr;
> > +
> > + p_addr += (sizeof(struct urbd0) * DESCS_COUNT);
> > + v_addr += (sizeof(struct urbd0) * DESCS_COUNT);
> > +
> > + /* Setup frbd */
> > + data->rxq.frbds_p_addr = p_addr;
> > + data->rxq.frbds = v_addr;
> > +
> > + p_addr += (sizeof(struct frbd) * DESCS_COUNT);
> > + v_addr += (sizeof(struct frbd) * DESCS_COUNT);
> > +
> > + /* Setup urbd1 */
> > + data->rxq.urbd1s_p_addr = p_addr;
> > + data->rxq.urbd1s = v_addr;
> > +
> > + p_addr += (sizeof(struct urbd1) * DESCS_COUNT);
> > + v_addr += (sizeof(struct urbd1) * DESCS_COUNT);
> > +
> > + /* Setup data buffers for txq */
> > + err = btintel_pcie_setup_txq_bufs(data, &data->txq);
> > + if (err) {
> > + BT_ERR("Failed to setup txq buffers: %d", err);
> > + goto exit_error_pool;
> > + }
> > +
> > + /* Setup data buffers for rxq */
> > + err = btintel_pcie_setup_rxq_bufs(data, &data->rxq);
> > + if (err) {
> > + BT_ERR("Failed to allocate rxq buffers: %d", err);
> > + goto exit_error_txq;
> > + }
> > +
> > + /* Setup Index Array */
> > + btintel_pcie_setup_ia(data, p_addr, v_addr, &data->ia);
> > +
> > + /* Setup Context Information */
> > + p_addr += sizeof(u16) * NUM_QUEUES * 4;
> > + v_addr += sizeof(u16) * NUM_QUEUES * 4;
> > +
> > + data->ci = v_addr;
> > + data->ci_p_addr = p_addr;
> > +
> > + /* Initialize the CI */
> > + btintel_pcie_init_ci(data, data->ci);
> > +
> > + return 0;
> > +
> > +exit_error_txq:
> > + btintel_pcie_free_txq_bufs(data, &data->txq);
> > +exit_error_pool:
> > + dma_pool_free(data->dma_pool, data->dma_v_addr, data->dma_p_addr);
> > + dma_pool_destroy(data->dma_pool);
> > +exit_error:
> > + return err;
> > +}
> > +
> > +static void btintel_pcie_release_hdev(struct btintel_pcie_data *data)
> > +{
> > + struct hci_dev *hdev;
> > +
> > + hdev = data->hdev;
> > + if (hdev) {
> > + hci_unregister_dev(hdev);
> > + hci_free_dev(hdev);
> > + }
> > + data->hdev = NULL;
> > +}
> > +
> > +static int btintel_pcie_setup_hdev(struct btintel_pcie_data *data)
> > +{
> > + /* TODO: initialize hdev and assign the callbacks to hdev */
> > + return -ENODEV;
> > +}
> > +
> > +static int btintel_pcie_probe(struct pci_dev *pdev,
> > + const struct pci_device_id *ent)
> > +{
> > + int err;
> > + struct btintel_pcie_data *data;
> > +
> > + if (!pdev)
> > + return -ENODEV;
> > +
> > + data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
> > + if (!data)
> > + return -ENOMEM;
> > +
> > + /* initialize the btintel_pcie data struct */
> > + data->pdev = pdev;
> > +
> > + spin_lock_init(&data->irq_lock);
> > + spin_lock_init(&data->hci_rx_lock);
> > +
> > + init_waitqueue_head(&data->gp0_wait_q);
> > + data->gp0_received = false;
> > +
> > + init_waitqueue_head(&data->tx_wait_q);
> > + data->tx_wait_done = false;
> > +
> > + data->workqueue = alloc_ordered_workqueue(KBUILD_MODNAME, WQ_HIGHPRI);
> > + if (!data->workqueue) {
> > + BT_ERR("Failed to create workqueue");
> > + return -ENOMEM;
> > + }
> > + skb_queue_head_init(&data->rx_skb_q);
> > + INIT_WORK(&data->rx_work, btintel_pcie_rx_work);
> > +
> > + data->boot_stage_cache = 0x00;
> > + data->img_resp_cache = 0x00;
> > +
> > + /* PCIe specific all to configure it for this device includes
> > + * enabling pice device, setting master, reading BAR[0], configuring
> > + * MSIx, setting DMA mask, and save the driver data.
> > + */
> > + err = btintel_pcie_config_pcie(pdev, data);
> > + if (err) {
> > + BT_ERR("Failed to config pcie (%d)", err);
> > + goto exit_error;
> > + }
> > +
> > + /* Set driver data for this PCI device */
> > + pci_set_drvdata(pdev, data);
> > +
> > + /* allocate the IPC struct */
> > + err = btintel_pcie_alloc(data);
> > + if (err) {
> > + BT_ERR("Failed to allocate queues(%d)", err);
> > + goto exit_error;
> > + }
> > +
> > + /* Enable BT function */
> > + err = btintel_pcie_enable_bt(data);
> > + if (err) {
> > + BT_ERR("Failed to start bluetooth device(%d)", err);
> > + goto exit_error;
> > + }
> > +
> > + /* CNV information (CNVi and CNVr) is in CSR */
> > + data->cnvi = btintel_pcie_rd_reg32(data, CSR_HW_REV_REG);
> > + BT_DBG("cnvi: 0x%08x", data->cnvi);
> > +
> > + data->cnvr = btintel_pcie_rd_reg32(data, CSR_RF_ID_REG);
> > + BT_DBG("cnvr: 0x%08x", data->cnvr);
> > +
> > + err = btintel_pcie_start_rx(data);
> > + if (err) {
> > + BT_ERR("Failed to start rx (%d)", err);
> > + goto exit_error;
> > + }
> > +
> > + err = btintel_pcie_setup_hdev(data);
> > + if (err) {
> > + BT_ERR("Failed to setup HCI module");
> > + goto exit_error;
> > + }
> > +
> > + return 0;
> > +
> > +exit_error:
> > + /* reset device before leave */
> > + btintel_pcie_reset_bt(data);
> > +
> > + /* clear bus mastering */
> > + pci_clear_master(pdev);
> > +
> > + /* Unset driver data for PCI device */
> > + pci_set_drvdata(pdev, NULL);
> > +
> > + return err;
> > +}
> > +
> > +static void btintel_pcie_remove(struct pci_dev *pdev)
> > +{
> > + struct btintel_pcie_data *data;
> > +
> > + if (!pdev) {
> > + BT_ERR("Invalid parameter: pdev");
> > + return;
> > + }
> > +
> > + data = pci_get_drvdata(pdev);
> > + if (!data) {
> > + BT_ERR("data is empty");
> > + return;
> > + }
> > +
> > + btintel_pcie_release_hdev(data);
> > +
> > + flush_work(&data->rx_work);
> > +
> > + destroy_workqueue(data->workqueue);
> > +
> > + btintel_pcie_free(data);
> > +
> > + /* reset device before leave */
> > + btintel_pcie_reset_bt(data);
> > +
> > + /* clear bus mastering */
> > + pci_clear_master(pdev);
> > +
> > + /* Unset driver data for PCI device */
> > + pci_set_drvdata(pdev, NULL);
> > +}
> > +
> > +#ifdef CONFIG_PM
> > +static int btintel_pcie_suspend(struct device *dev)
> > +{
> > + /* TODO: Add support suspend */
> > + return 0;
> > +}
> > +
> > +static int btintel_pcie_resume(struct device *dev)
> > +{
> > + /* TODO: Add support resume */
> > + return 0;
> > +}
> > +
> > +static SIMPLE_DEV_PM_OPS(btintel_pcie_pm_ops, btintel_pcie_suspend,
> > + btintel_pcie_resume);
> > +#endif /* CONFIG_PM */
> > +
> > +static struct pci_driver btintel_pcie_driver = {
> > + .name = KBUILD_MODNAME,
> > + .id_table = btintel_pcie_table,
> > + .probe = btintel_pcie_probe,
> > + .remove = btintel_pcie_remove,
> > +#ifdef CONFIG_PM
> > + .driver.pm = &btintel_pcie_pm_ops,
> > +#endif /* CONFIG_PM */
> > +};
> > +module_pci_driver(btintel_pcie_driver);
> > +
> > +MODULE_AUTHOR("Tedd Ho-Jeong An <tedd.an@intel.com>");
> > +MODULE_DESCRIPTION("Intel Bluetooth PCIe transport driver ver " VERSION);
> > +MODULE_VERSION(VERSION);
> > +MODULE_LICENSE("GPL");
>
> Botton line: We have to tone down the debbuging since it pretting a
> lot of useless information and when it does it prints with old BT_DBG
> macros which doesn't print the controller info so on system with
> multiple controller that would be impossible to say which controller
> is generating the logs.
>
> > diff --git a/drivers/bluetooth/btintel_pcie.h b/drivers/bluetooth/btintel_pcie.h
> > new file mode 100644
> > index 000000000000..1554964686bd
> > --- /dev/null
> > +++ b/drivers/bluetooth/btintel_pcie.h
> > @@ -0,0 +1,449 @@
> > +/* SPDX-License-Identifier: GPL-2.0-or-later */
> > +/*
> > + * Intel Bluetooth PCIE driver
> > + *
> > + * Copyright (C) 2017 Intel Corporation. All rights reserved.
>
> Ditto.
>
> > + *
> > + * This program is free software; you can redistribute it and/or
> > + * modify it under the terms of the GNU General Public License version
> > + * 2 as published by the Free Software Foundation.
> > + *
> > + * This program is distributed in the hope that it will be useful,
> > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> > + * GNU General Public License for more details.
> > + *
> > + * Copyright (C) 2022 Intel Corporation
> > + *
> > + * Intel Bluetooth Driver for PCIE interface.
> > + */
> > +
> > +/* Control and Status Register(CSR) */
> > +#define CSR_BASE (0x000)
> > +#define CSR_FUNC_CTRL_REG (CSR_BASE + 0x024)
> > +#define CSR_HW_REV_REG (CSR_BASE + 0x028)
> > +#define CSR_RF_ID_REG (CSR_BASE + 0x09C)
> > +#define CSR_BOOT_STAGE_REG (CSR_BASE + 0x108)
> > +#define CSR_CI_ADDR_LSB_REG (CSR_BASE + 0x118)
> > +#define CSR_CI_ADDR_MSB_REG (CSR_BASE + 0x11C)
> > +#define CSR_IMG_RESPONSE_REG (CSR_BASE + 0x12C)
> > +#define CSR_HBUS_TARG_WRPTR (CSR_BASE + 0x460)
> > +
> > +/* CSR Function Control Register */
> > +#define CSR_FUNC_CTRL_FUNC_ENA (BIT(0))
> > +#define CSR_FUNC_CTRL_MAC_INIT (BIT(6))
> > +#define CSR_FUNC_CTRL_FUNC_INIT (BIT(7))
> > +#define CSR_FUNC_CTRL_MAC_ACCESS_STS (BIT(20))
> > +#define CSR_FUNC_CTRL_SW_RESET (BIT(31))
> > +
> > +/* Value for CSR_BOOT_STAGE register */
> > +#define CSR_BOOT_STAGE_ROM (BIT(0))
> > +#define CSR_BOOT_STAGE_IML (BIT(1))
> > +#define CSR_BOOT_STAGE_OPFW (BIT(2))
> > +#define CSR_BOOT_STAGE_ROM_LOCKDOWN (BIT(10))
> > +#define CSR_BOOT_STAGE_IML_LOCKDOWN (BIT(11))
> > +#define CSR_BOOT_STAGE_MAC_ACCESS_ON (BIT(16))
> > +#define CSR_BOOT_STAGE_ALIVE (BIT(23))
> > +
> > +/* Registers for MSIX */
> > +#define CSR_MSIX_BASE (0x2000)
> > +#define CSR_MSIX_FH_INT_CAUSES (CSR_MSIX_BASE + 0x0800)
> > +#define CSR_MSIX_FH_INT_MASK (CSR_MSIX_BASE + 0x0804)
> > +#define CSR_MSIX_HW_INT_CAUSES (CSR_MSIX_BASE + 0x0808)
> > +#define CSR_MSIX_HW_INT_MASK (CSR_MSIX_BASE + 0x080C)
> > +#define CSR_MSIX_AUTOMASK_ST (CSR_MSIX_BASE + 0x0810)
> > +#define CSR_MSIX_AUTOMASK_EN (CSR_MSIX_BASE + 0x0814)
> > +#define CSR_MSIX_IVAR_BASE (CSR_MSIX_BASE + 0x0880)
> > +#define CSR_MSIX_IVAR(cause) (CSR_MSIX_IVAR_BASE + (cause))
> > +
> > +/* Causes for the FH register interrupts */
> > +enum msix_fh_int_causes {
> > + MSIX_FH_INT_CAUSES_0 = BIT(0), /* cause 0 */
> > + MSIX_FH_INT_CAUSES_1 = BIT(1), /* cause 1 */
> > +};
> > +
> > +/* Causes for the HW register interrupts */
> > +enum msix_hw_int_causes {
> > + MSIX_HW_INT_CAUSES_GP0 = BIT(0), /* cause 32 */
> > +};
> > +
> > +#define MSIX_NON_AUTO_CLEAR_CAUSE BIT(7)
> > +
> > +/* Minimum and Maximum number of MSIx Vector
> > + * Intel Bluetooth PCIe support only 1 vector
> > + */
> > +#define MSIX_VEC_MAX 1
> > +#define MSIX_VEC_MIN 1
> > +
> > +/* Default Poll time for MAC access during init*/
> > +#define DEFAULT_MAC_ACCESS_TIMEOUT 200000
> > +
> > +/* Default interrupt timeout in msec */
> > +#define DEFAULT_INTR_TIMEOUT 3000
> > +
> > +/* The number of descriptors in TX/RX queues */
> > +#define DESCS_COUNT 16
> > +
> > +/* Number of Queue for TX and RX
> > + * It indicates the index of the IA(Index Array)
> > + */
> > +enum {
> > + TXQ_NUM = 0,
> > + RXQ_NUM = 1,
> > + NUM_QUEUES = 2,
> > +};
> > +
> > +/* The size of DMA buffer for TX and RX */
> > +#define BUFFER_SIZE 4096
> > +
> > +/* DMA allocation alignment */
> > +#define DMA_POOL_ALIGNMENT 256
> > +
> > +/* TX wait time (jiffies) */
> > +#define TX_WAIT_TIMEOUT 500
> > +
> > +/* Number of pending RX requests for downlink */
> > +#define RX_MAX_QUEUE 6
> > +
> > +/* Enum for RBD buffer size mappting */
> > +enum {
> > + RBD_SIZE_1K = 0x1,
> > + RBD_SIZE_2K = 0x2,
> > + RBD_SIZE_4K = 0x4,
> > + RBD_SIZE_8K = 0x8,
> > + RBD_SIZE_12K = 0x9,
> > + RBD_SIZE_16K = 0xA,
> > + RBD_SIZE_20K = 0xB,
> > + RBD_SIZE_24K = 0xC,
> > + RBD_SIZE_28K = 0xD,
> > + RBD_SIZE_32K = 0xE,
> > +};
> > +
> > +/*
> > + * Struct for Context Information (v2)
> > + *
> > + * All members are write-only for host and read-only for device.
> > + *
> > + * @version: Version of context information
> > + * @size: Size of context information
> > + * @config: Config with which host wants peripheral to execute
> > + * Subset of capability register published by device
> > + * @addr_tr_hia: Address of TR Head Index Array
> > + * @addr_tr_tia: Address of TR Tail Index Array
> > + * @addr_cr_hia: Address of CR Head Index Array
> > + * @addr_cr_tia: Address of CR Tail Index Array
> > + * @num_tr_ia: Number of entries in TR Index Arrays
> > + * @num_cr_ia: Number of entries in CR Index Arrays
> > + * @rbd_siz: RBD Size { 0x4=4K }
> > + * @addr_tfdq: Address of TFD Queue(tx)
> > + * @addr_urbdq0: Address of URBD Queue(tx)
> > + * @num_tfdq: Number of TFD in TFD Queue(tx)
> > + * @num_urbdq0: Number of URBD in URBD Queue(tx)
> > + * @tfdq_db_vec: Queue number of TFD
> > + * @urbdq0_db_vec: Queue number of URBD
> > + * @addr_frbdq: Address of FRBD Queue(rx)
> > + * @addr_urbdq1: Address of URBD Queue(rx)
> > + * @num_frbdq: Number of FRBD in FRBD Queue(rx)
> > + * @frbdq_db_vec: Queue number of FRBD
> > + * @num_urbdq1: Number of URBD in URBD Queue(rx)
> > + * @urbdq_db_vec: Queue number of URBDQ1
> > + * @tr_msi_vec: Transfer Ring MSI Vector
> > + * @cr_msi_vec: Completion Ring MSI Vector
> > + * @dbgc_addr: DBGC first fragmemt address
> > + * @dbgc_size: DBGC buffer size
> > + * @early_enable: Enarly debug enable
> > + * @dbg_output_mode: Debug output mode
> > + * Bit[4] DBGC O/P { 0=SRAM, 1=DRAM(not relevant for NPK) }
> > + * Bit[5] DBGC I/P { 0=BDBG, 1=DBGI }
> > + * Bits[6:7] DBGI O/P(relevant if bit[5] = 1)
> > + * 0=BT DBGC, 1=WiFi DBGC, 2=NPK }
> > + * @dbg_preset: Debug preset
> > + * @ext_addr: Address of context information extension
> > + * @ext_size: Size of context information part
> > + *
> > + * Total 38 DWords
> > + *
> > + */
> > +struct ctx_info {
> > + u16 version;
> > + u16 size;
> > + u32 config;
> > + u32 reserved_dw02;
> > + u32 reserved_dw03;
> > + u64 addr_tr_hia;
> > + u64 addr_tr_tia;
> > + u64 addr_cr_hia;
> > + u64 addr_cr_tia;
> > + u16 num_tr_ia;
> > + u16 num_cr_ia;
> > + u32 rbd_size:4,
> > + reserved_dw13:28;
> > + u64 addr_tfdq;
> > + u64 addr_urbdq0;
> > + u16 num_tfdq;
> > + u16 num_urbdq0;
> > + u16 tfdq_db_vec;
> > + u16 urbdq0_db_vec;
> > + u64 addr_frbdq;
> > + u64 addr_urbdq1;
> > + u16 num_frbdq;
> > + u16 frbdq_db_vec;
> > + u16 num_urbdq1;
> > + u16 urbdq_db_vec;
> > + u16 tr_msi_vec;
> > + u16 cr_msi_vec;
> > + u32 reserved_dw27;
> > + u64 dbgc_addr;
> > + u32 dbgc_size;
> > + u32 early_enable:1,
> > + reserved_dw31:3,
> > + dbg_output_mode:4,
> > + dbg_preset:8,
> > + reserved2_dw31:16;
> > + u64 ext_addr;
> > + u32 ext_size;
> > + u32 test_param;
> > + u32 reserved_dw36;
> > + u32 reserved_dw37;
> > +} __packed;
> > +
> > +/* Transfer Descriptor for TX
> > + * @type: Not in use. Set to 0x0
> > + * @size: Size of data in the buffer
> > + * @addr: DMA Address of buffer
> > + */
> > +struct tfd {
> > + u8 type;
> > + u16 size;
> > + u8 reserved;
> > + u64 addr;
> > + u32 reserved1;
> > +} __packed;
> > +
> > +/* URB Descriptor for TX
> > + * @tfd_index: Index of TFD in TFDQ + 1
> > + * @num_txq: Queue index of TFD Queue
> > + * @cmpl_count: Completion count. Always 0x01
> > + * @immediate_cmpl: Immediate completion flag: Always 0x01
> > + */
> > +struct urbd0 {
> > + u32 tfd_index:16,
> > + num_txq:8,
> > + cmpl_count:4,
> > + reserved:3,
> > + immediate_cmpl:1;
> > +} __packed;
> > +
> > +/* FRB Descriptor for RX
> > + * @tag: RX buffer tag (index of RX buffer queue)
> > + * @addr: Address of buffer
> > + */
> > +struct frbd {
> > + u32 tag:16,
> > + reserved:16;
> > + u32 reserved2;
> > + u64 addr;
> > +} __packed;
> > +
> > +/* URB Descriptor for RX
> > + * @frbd_tag: Tag from FRBD
> > + * @status: Status
> > + */
> > +struct urbd1 {
> > + u32 frbd_tag:16,
> > + status:1,
> > + reserved:14,
> > + fixed:1;
> > +} __packed;
> > +
> > +/* RFH header in RX packet
> > + * @packet_len: Length of the data in the buffer
> > + * @rxq: RX Queue number
> > + * @cmd_id: Command ID. Not in Use
> > + */
> > +struct rfh_hdr {
> > + u64 packet_len:16,
> > + rxq:6,
> > + reserved:10,
> > + cmd_id:16,
> > + reserved1:16;
> > +} __packed;
> > +
> > +/* Internal data buffer
> > + * @data: pointer to the data buffer
> > + * @p_addr: physical address of data buffer
> > + */
> > +struct data_buf {
> > + u8 *data;
> > + dma_addr_t data_p_addr;
> > +};
> > +
> > +/* Index Array */
> > +struct ia {
> > + dma_addr_t tr_hia_p_addr;
> > + u16 *tr_hia;
> > + dma_addr_t tr_tia_p_addr;
> > + u16 *tr_tia;
> > + dma_addr_t cr_hia_p_addr;
> > + u16 *cr_hia;
> > + dma_addr_t cr_tia_p_addr;
> > + u16 *cr_tia;
> > +};
> > +
> > +/* Structure for TX Queue
> > + * @count: Number of descriptors
> > + * @tfds: Array of TFD
> > + * @urbd0s: Array of URBD0
> > + * @buf: Array of data_buf structure
> > + */
> > +struct txq {
> > + u16 count;
> > +
> > + dma_addr_t tfds_p_addr;
> > + struct tfd *tfds;
> > +
> > + dma_addr_t urbd0s_p_addr;
> > + struct urbd0 *urbd0s;
> > +
> > + dma_addr_t buf_p_addr;
> > + void *buf_v_addr;
> > + struct data_buf *bufs;
> > +};
> > +
> > +/* Structure for RX Queue
> > + * @count: Number of descriptors
> > + * @frbds: Array of FRBD
> > + * @urbd1s: Array of URBD1
> > + * @buf: Array of data_buf structure
> > + */
> > +struct rxq {
> > + u16 count;
> > +
> > + dma_addr_t frbds_p_addr;
> > + struct frbd *frbds;
> > +
> > + dma_addr_t urbd1s_p_addr;
> > + struct urbd1 *urbd1s;
> > +
> > + dma_addr_t buf_p_addr;
> > + void *buf_v_addr;
> > + struct data_buf *bufs;
> > +};
> > +
> > +/* struct btintel_pcie_data
> > + * @pdev: pci device
> > + * @hdev: hdev device
> > + * @flags: driver state
> > + * @irq_lock: spinlock for MSIX
> > + * @hci_rx_lock: spinlock for HCI RX flow
> > + * @base_addr: pci base address (from BAR)
> > + * @msix_entries: array of MSIX entries
> > + * @msix_enabled: true if MSIX is enabled;
> > + * @alloc_vecs: number of interrupt vectors allocated
> > + * @def_irq: default irq for all causes
> > + * @fh_init_mask: initial unmasked rxq causes
> > + * @hw_init_mask: initial unmaksed hw causes
> > + * @boot_stage_cache: cached value of boot stage register
> > + * @img_resp_cache: cached value of image response register
> > + * @cnvi: CNVi register value
> > + * @cnvr: CNVr register value
> > + * @gp0_received: condition for gp0 interrupt
> > + * @gp0_wait_q: wait_q for gp0 interrupt
> > + * @tx_wait_done: condition for tx interrupt
> > + * @tx_wait_q: wait_q for tx interrupt
> > + * @workqueue: workqueue for RX work
> > + * @rx_skb_q: SKB queue for RX packet
> > + * @rx_work: RX work struct to process the RX packet in @rx_skb_q
> > + * @dma_pool: DMA pool for descriptors, index array and ci
> > + * @dma_p_addr: DMA address for pool
> > + * @dma_v_addr: address of pool
> > + * @ci_p_addr: DMA address for CI struct
> > + * @ci: CI struct
> > + * @ia: Index Array struct
> > + * @txq: TX Queue struct
> > + * @rxq: RX Queue struct
> > + */
> > +struct btintel_pcie_data {
> > + struct pci_dev *pdev;
> > + struct hci_dev *hdev;
> > +
> > + unsigned long flags;
> > + /* lock used in MSIX interrupt */
> > + spinlock_t irq_lock;
> > + /* lock to serialize rx events */
> > + spinlock_t hci_rx_lock;
> > +
> > + void __iomem *base_addr;
> > +
> > + struct msix_entry msix_entries[MSIX_VEC_MAX];
> > + bool msix_enabled;
> > + u32 alloc_vecs;
> > + u32 def_irq;
> > +
> > + u32 fh_init_mask;
> > + u32 hw_init_mask;
> > +
> > + u32 boot_stage_cache;
> > + u32 img_resp_cache;
> > +
> > + u32 cnvi;
> > + u32 cnvr;
> > +
> > + bool gp0_received;
> > + wait_queue_head_t gp0_wait_q;
> > +
> > + bool tx_wait_done;
> > + wait_queue_head_t tx_wait_q;
> > +
> > + struct workqueue_struct *workqueue;
> > + struct sk_buff_head rx_skb_q;
> > + struct work_struct rx_work;
> > +
> > + struct dma_pool *dma_pool;
> > + dma_addr_t dma_p_addr;
> > + void *dma_v_addr;
> > +
> > + dma_addr_t ci_p_addr;
> > + struct ctx_info *ci;
> > + struct ia ia;
> > + struct txq txq;
> > + struct rxq rxq;
> > +};
> > +
> > +static inline u32 btintel_pcie_rd_reg32(struct btintel_pcie_data *data,
> > + u32 offset)
> > +{
> > + return ioread32(data->base_addr + offset);
> > +}
> > +
> > +static inline void btintel_pcie_wr_reg8(struct btintel_pcie_data *data,
> > + u32 offset, u8 val)
> > +{
> > + iowrite8(val, data->base_addr + offset);
> > +}
> > +
> > +static inline void btintel_pcie_wr_reg32(struct btintel_pcie_data *data,
> > + u32 offset, u32 val)
> > +{
> > + iowrite32(val, data->base_addr + offset);
> > +}
> > +
> > +static inline void btintel_pcie_set_reg_bits(struct btintel_pcie_data *data,
> > + u32 offset, u32 bits)
> > +{
> > + u32 r;
> > +
> > + r = ioread32(data->base_addr + offset);
> > + r |= bits;
> > + iowrite32(r, data->base_addr + offset);
> > +}
> > +
> > +static inline void btintel_pcie_clr_reg_bits(struct btintel_pcie_data *data,
> > + u32 offset, u32 bits)
> > +{
> > + u32 r;
> > +
> > + r = ioread32(data->base_addr + offset);
> > + r &= ~bits;
> > + iowrite32(r, data->base_addr + offset);
> > +}
> > --
> > 2.34.1
>
> All symbols must be properly prefixed with BTINTEL_PCIE
>
> >
>
>
> --
> Luiz Augusto von Dentz
--
Luiz Augusto von Dentz
^ permalink raw reply [flat|nested] 16+ messages in thread* RE: [PATCH v1 2/3] Bluetooth: btintel_pcie: Add support for PCIE transport
2024-03-28 14:09 ` Luiz Augusto von Dentz
2024-03-28 14:13 ` Luiz Augusto von Dentz
@ 2024-05-07 14:39 ` K, Kiran
1 sibling, 0 replies; 16+ messages in thread
From: K, Kiran @ 2024-05-07 14:39 UTC (permalink / raw)
To: Luiz Augusto von Dentz
Cc: linux-bluetooth@vger.kernel.org, Srivatsa, Ravishankar,
Tumkur Narayan, Chethan, An, Tedd
Hi Luiz,
Thanks for your comments.
> -----Original Message-----
> From: Luiz Augusto von Dentz <luiz.dentz@gmail.com>
> Sent: Thursday, March 28, 2024 7:39 PM
> To: K, Kiran <kiran.k@intel.com>
> Cc: linux-bluetooth@vger.kernel.org; Srivatsa, Ravishankar
> <ravishankar.srivatsa@intel.com>; Tumkur Narayan, Chethan
> <chethan.tumkur.narayan@intel.com>; An, Tedd <tedd.an@intel.com>
> Subject: Re: [PATCH v1 2/3] Bluetooth: btintel_pcie: Add support for PCIE
> transport
>
> Hi Kiran,
>
> On Thu, Mar 28, 2024 at 7:05 AM Kiran K <kiran.k@intel.com> wrote:
> >
> > From: Tedd Ho-Jeong An <tedd.an@intel.com>
> >
> > Add initial code to support Intel bluetooth devices based on PICE
> > transport. This patch allocates memory for buffers, internal structures,
> > initializes interrupts for TX & RX and initializes PCIE device.
> >
> > Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
> > Co-developed-by: Kiran K <kiran.k@intel.com>
> > Signed-off-by: Kiran K <kiran.k@intel.com>
> > ---
> > drivers/bluetooth/Kconfig | 14 +
> > drivers/bluetooth/Makefile | 1 +
> > drivers/bluetooth/btintel.h | 2 +-
> > drivers/bluetooth/btintel_pcie.c | 1317
> ++++++++++++++++++++++++++++++
> > drivers/bluetooth/btintel_pcie.h | 449 ++++++++++
> > 5 files changed, 1782 insertions(+), 1 deletion(-)
> > create mode 100644 drivers/bluetooth/btintel_pcie.c
> > create mode 100644 drivers/bluetooth/btintel_pcie.h
> >
> > diff --git a/drivers/bluetooth/Kconfig b/drivers/bluetooth/Kconfig
> > index bc211c324206..387f7b14461d 100644
> > --- a/drivers/bluetooth/Kconfig
> > +++ b/drivers/bluetooth/Kconfig
> > @@ -23,6 +23,20 @@ config BT_MTK
> > tristate
> > select FW_LOADER
> >
> > +config BT_INTEL_PCIE
> > + tristate "Intel Bluetooth transport driver for PCIe"
> > + depends on PCI
> > + select BT_INTEL
> > + select FW_LOADER
> > + default y
> > + help
> > + Intel Bluetooth transport driver for PCIe.
> > + This driver is required if you want to use Intel Bluetooth device
> > + with PCIe interface.
> > +
> > + Say Y here to compiler support for Intel Bluetooth PCIe device into
> > + the kernel or say M to compile it as module (btintel_pcie)
> > +
> > config BT_HCIBTUSB
> > tristate "HCI USB driver"
> > depends on USB
> > diff --git a/drivers/bluetooth/Makefile b/drivers/bluetooth/Makefile
> > index 7a5967e9ac48..0730d6684d1a 100644
> > --- a/drivers/bluetooth/Makefile
> > +++ b/drivers/bluetooth/Makefile
> > @@ -17,6 +17,7 @@ obj-$(CONFIG_BT_HCIBTUSB) += btusb.o
> > obj-$(CONFIG_BT_HCIBTSDIO) += btsdio.o
> >
> > obj-$(CONFIG_BT_INTEL) += btintel.o
> > +obj-$(CONFIG_BT_INTEL_PCIE) += btintel_pcie.o btintel.o
> > obj-$(CONFIG_BT_ATH3K) += ath3k.o
> > obj-$(CONFIG_BT_MRVL) += btmrvl.o
> > obj-$(CONFIG_BT_MRVL_SDIO) += btmrvl_sdio.o
> > diff --git a/drivers/bluetooth/btintel.h b/drivers/bluetooth/btintel.h
> > index 1462a57420a0..5d4685b5c1fa 100644
> > --- a/drivers/bluetooth/btintel.h
> > +++ b/drivers/bluetooth/btintel.h
> > @@ -209,7 +209,7 @@ struct btintel_data {
> > #define btintel_wait_on_flag_timeout(hdev, nr, m, to) \
> > wait_on_bit_timeout(btintel_get_flag(hdev), (nr), m, to)
> >
> > -#if IS_ENABLED(CONFIG_BT_INTEL)
> > +#if IS_ENABLED(CONFIG_BT_INTEL) ||
> IS_ENABLED(CONFIG_BT_INTEL_PCIE)
> >
> > int btintel_check_bdaddr(struct hci_dev *hdev);
> > int btintel_enter_mfg(struct hci_dev *hdev);
> > diff --git a/drivers/bluetooth/btintel_pcie.c
> b/drivers/bluetooth/btintel_pcie.c
> > new file mode 100644
> > index 000000000000..e6ce2304dc57
> > --- /dev/null
> > +++ b/drivers/bluetooth/btintel_pcie.c
> > @@ -0,0 +1,1317 @@
> > +// SPDX-License-Identifier: GPL-2.0-or-later
> > +/*
> > + * Intel Bluetooth PCIE driver
> > + *
> > + * Copyright (C) 2017 Intel Corporation. All rights reserved.
>
> The above shall probably be updated to 2024, also the All rights
> reserved don't actually fit well with GPL so please remove it.
Ack.
>
> > + * This program is free software; you can redistribute it and/or
> > + * modify it under the terms of the GNU General Public License version
> > + * 2 as published by the Free Software Foundation.
> > + *
> > + * This program is distributed in the hope that it will be useful,
> > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> > + * GNU General Public License for more details.
> > + *
> > + * Copyright (C) 2022 Intel Corporation
>
> See above.
Ack.
>
> > + * Intel Bluetooth Driver for PCIE interface.
> > + */
> > +#include <linux/kernel.h>
> > +#include <linux/module.h>
> > +#include <linux/firmware.h>
> > +#include <linux/pci.h>
> > +#include <linux/wait.h>
> > +#include <linux/delay.h>
> > +#include <linux/interrupt.h>
> > +
> > +#include <asm/unaligned.h>
> > +
> > +#include <net/bluetooth/bluetooth.h>
> > +#include <net/bluetooth/hci_core.h>
> > +
> > +#include "btintel.h"
> > +#include "btintel_pcie.h"
> > +
> > +#define VERSION "0.1"
> > +
> > +#define BTINTEL_PCI_DEVICE(dev, subdev) \
> > + .vendor = PCI_VENDOR_ID_INTEL, \
> > + .device = (dev), \
> > + .subvendor = PCI_ANY_ID, \
> > + .subdevice = (subdev), \
> > + .driver_data = 0
> > +
> > +/* Intel Bluetooth PCIe device id table */
> > +static const struct pci_device_id btintel_pcie_table[] = {
> > + { BTINTEL_PCI_DEVICE(0xA876, PCI_ANY_ID) },
> > + { 0 }
> > +};
> > +MODULE_DEVICE_TABLE(pci, btintel_pcie_table);
> > +
> > +/* Intel PCIe uses 4 bytes of HCI type instead of 1 byte BT SIG HCI type */
> > +#define BTINTEL_PCIE_HCI_TYPE_LEN 4
> > +#define BTINTEL_PCIE_HCI_CMD_PKT 0x00000001
> > +#define BTINTEL_PCIE_HCI_ACL_PKT 0x00000002
> > +#define BTINTEL_PCIE_HCI_SCO_PKT 0x00000003
> > +#define BTINTEL_PCIE_HCI_EVT_PKT 0x00000004
> > +
> > +#define BTITNEL_PCIE_ENABLE_HCI_DUMP 0
> > +
> > +#if BTITNEL_PCIE_ENABLE_HCI_DUMP
> > +static inline void btintel_pcie_hci_dump(const char *p, const void *b, int s)
> > +{
> > + const unsigned char *ptr = (const unsigned char *)b;
> > + char str[64];
> > + int c, i;
> > +
> > + for (i = c = 0; c < s; c++) {
> > + i += snprintf(str + i, sizeof(str) - i, "%02x ", ptr[c]);
> > + if ((c > 0 && (c + 1) % 8 == 0) || (c == s - 1)) {
> > + BT_DBG("%s: %s", p, str);
> > + i = 0;
> > + }
> > + }
> > +}
> > +#else
> > +static inline void btintel_pcie_hci_dump(const char *p, const void *b, int s)
> > +{
> > +}
> > +#endif
>
> We have the monitor to process HCI traffic, not really sure what is
> the purpose with the functions above.
Ack. I will remove this function.
>
> > +static void ipc_print_ia_ring(struct ia *ia, u16 queue_num)
> > +{
> > + BT_DBG("[%s] ---------------- ia ----------------",
> > + queue_num == TXQ_NUM ? "TXQ" : "RXQ");
> > + BT_DBG("[%s] tr-h:%02u tr-t:%02u cr-h:%02u cr-t:%02u",
> > + queue_num == TXQ_NUM ? "TXQ" : "RXQ",
> > + ia->tr_hia[queue_num], ia->tr_tia[queue_num],
> > + ia->cr_hia[queue_num], ia->cr_tia[queue_num]);
> > +}
> > +
> > +static void ipc_print_urbd0(struct urbd0 *urbd0, u16 index)
> > +{
> > + BT_DBG("[TXQ] -------------- urbd0[%u] --------------", index);
> > + BT_DBG("[TXQ] tfd_index:%u num_txq:%u cmpl_cnt:%u
> immediate_cmpl:0x%x",
> > + urbd0->tfd_index, urbd0->num_txq, urbd0->cmpl_count,
> > + urbd0->immediate_cmpl);
> > +}
> > +
> > +static void ipc_print_frbd(struct frbd *frbd, u16 index)
> > +{
> > + BT_DBG("[RXQ] -------------- frbd[%u] --------------", index);
> > + BT_DBG("[RXQ] tag:%u addr:0x%llx", frbd->tag, frbd->addr);
> > +}
> > +
> > +static void ipc_print_urbd1(struct urbd1 *urbd1, u16 index)
> > +{
> > + BT_DBG("[RXQ] -------------- urbd1[%u] --------------", index);
> > + BT_DBG("[RXQ] frbd_tag:%u status: 0x%x fixed:0x%x",
> > + urbd1->frbd_tag, urbd1->status, urbd1->fixed);
> > +}
>
> We need to replace usage of BT_DBG with bt_dev_dbg, etc.
Ack. I keep only relevant logs / logging functions.
>
> > +/* Poll internal in microseconds */
> > +#define POLL_INTERVAL 10
> > +
> > +static int btintel_pcie_poll_bit(struct btintel_pcie_data *data, u32 offset,
> > + u32 bits, u32 mask, int timeout)
> > +{
> > + int t = 0;
> > + u32 reg;
> > +
> > + BT_DBG("Enter poll_bit");
> > + do {
> > + reg = btintel_pcie_rd_reg32(data, offset);
> > + BT_DBG("CURRENT FUNC_CTRL_REG: 0x%x", reg);
> > +
> > + if ((reg & mask) == (bits & mask)) {
> > + BT_DBG("Poll bit matched");
> > + return t;
> > + }
> > + udelay(POLL_INTERVAL);
> > + t += POLL_INTERVAL;
> > + BT_DBG("Poll wait: %d", t);
> > + } while (t < timeout);
>
> Way too much debugging for such a trivial function, I'd actually
> remove all calls to BT_DBG here.
Ack.
>
> > + return -ETIMEDOUT;
> > +}
> > +
> > +static struct btintel_pcie_data *btintel_pcie_get_data(struct msix_entry
> *entry)
> > +{
> > + u8 queue = entry->entry;
> > + struct msix_entry *entries = entry - queue;
> > +
> > + return container_of(entries, struct btintel_pcie_data, msix_entries[0]);
> > +}
> > +
> > +/* Set the doorbell for RXQ to notify the device that @index(actually index-
> 1)
> > + * is available to receive the data
> > + */
> > +static void btintel_pcie_set_rx_db(struct btintel_pcie_data *data, u16
> index)
> > +{
> > + u32 val;
> > +
> > + val = index;
> > + val |= (513 << 16);
> > +
> > + BT_DBG("[RXQ] Set doorbell for index: %u", index);
> > + btintel_pcie_wr_reg32(data, CSR_HBUS_TARG_WRPTR, val);
> > +}
> > +
> > +/* Update the FRBD(free buffer descriptor) with the @frbd_index and the
> > + * DMA address of the free buffer.
> > + */
> > +static void btintel_pcie_prepare_rx(struct rxq *rxq, u16 frbd_index)
> > +{
> > + struct data_buf *buf;
> > + struct frbd *frbd;
> > +
> > + /* Get the buffer of the frbd for DMA */
> > + buf = &rxq->bufs[frbd_index];
> > +
> > + frbd = &rxq->frbds[frbd_index];
> > + memset(frbd, 0, sizeof(*frbd));
> > +
> > + /* Update FRBD */
> > + frbd->tag = frbd_index;
> > + frbd->addr = buf->data_p_addr;
> > + ipc_print_frbd(frbd, frbd_index);
> > +}
> > +
> > +static int btintel_pcie_submit_rx(struct btintel_pcie_data *data)
> > +{
> > + u16 frbd_index;
> > + struct rxq *rxq = &data->rxq;
> > +
> > + /* Read the frbd index from the TR_HIA(Head Index Array) for RXQ */
> > + frbd_index = data->ia.tr_hia[RXQ_NUM];
> > + BT_DBG("[RXQ] current frbd_index: %u", frbd_index);
> > +
> > + /* Make sure the index value is within the range. It shouldn't be
> > + * bigger than the total count of the queue.
> > + */
> > + if (frbd_index > rxq->count) {
> > + BT_ERR("[RXQ] RXQ out of range: (0x%x)", frbd_index);
> > + return -ERANGE;
> > + }
> > +
> > + /* Prepare for RX submit. It updates the FRBD with the address of DMA
> > + * buffer
> > + */
> > + btintel_pcie_prepare_rx(rxq, frbd_index);
> > +
> > + /* Update TR_HIA with new FRBD index */
> > + frbd_index = (frbd_index + 1) % rxq->count;
> > + data->ia.tr_hia[RXQ_NUM] = frbd_index;
> > + ipc_print_ia_ring(&data->ia, RXQ_NUM);
> > +
> > + /* Set the doorbell to notify the device */
> > + btintel_pcie_set_rx_db(data, frbd_index);
> > +
> > + BT_DBG("[RXQ] rx sumbit completed");
> > +
> > + return 0;
> > +}
> > +
> > +static int btintel_pcie_start_rx(struct btintel_pcie_data *data)
> > +{
> > + int i, ret;
> > +
> > + for (i = 0; i < RX_MAX_QUEUE; i++) {
> > + ret = btintel_pcie_submit_rx(data);
> > + if (ret) {
> > + BT_ERR("[RXQ] failed to submit frbd(%d)", ret);
> > + return ret;
> > + }
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static void btintel_pcie_reset_ia(struct btintel_pcie_data *data)
> > +{
> > + memset(data->ia.tr_hia, 0, sizeof(u16) * NUM_QUEUES);
> > + memset(data->ia.tr_tia, 0, sizeof(u16) * NUM_QUEUES);
> > + memset(data->ia.cr_hia, 0, sizeof(u16) * NUM_QUEUES);
> > + memset(data->ia.cr_tia, 0, sizeof(u16) * NUM_QUEUES);
> > + BT_DBG("Index Arrays are reset");
> > +}
> > +
> > +static void btintel_pcie_reset_bt(struct btintel_pcie_data *data)
> > +{
> > + BT_INFO("Reset BT Function ");
> > + btintel_pcie_wr_reg32(data, CSR_FUNC_CTRL_REG,
> CSR_FUNC_CTRL_SW_RESET);
> > +}
> > +
> > +/* This function enables BT function by setting CSR_FUNC_CTRL_MAC_INIT
> bit in
> > + * CSR_FUNC_CTRL_REG register and wait for MSI-X with
> MSIX_HW_INT_CAUSES_GP0.
> > + * Then the host reads firmware version from CSR_F2D_MBX and the boot
> stage
> > + * from CSR_BOOT_STAGE_REG.
> > + */
> > +static int btintel_pcie_enable_bt(struct btintel_pcie_data *data)
> > +{
> > + int err;
> > + u32 reg;
> > +
> > + data->gp0_received = false;
> > +
> > + /* Update the DMA address of CI struct to CSR */
> > + btintel_pcie_wr_reg32(data, CSR_CI_ADDR_LSB_REG,
> > + data->ci_p_addr & 0xffffffff);
> > + btintel_pcie_wr_reg32(data, CSR_CI_ADDR_MSB_REG,
> > + data->ci_p_addr >> 32);
> > +
> > + /* Reset the cached value of boot stage. it is updated by the msix
> > + * gp0 interrupt handler.
> > + */
> > + data->boot_stage_cache = 0x0;
> > +
> > + /* Set MAC_INIT bit to start primary bootloader */
> > + reg = btintel_pcie_rd_reg32(data, CSR_FUNC_CTRL_REG);
> > + BT_INFO("Before: FUNC_CTRL_REG: 0x%x", reg);
> > +
> > + btintel_pcie_set_reg_bits(data, CSR_FUNC_CTRL_REG,
> > + CSR_FUNC_CTRL_MAC_INIT);
> > + BT_INFO("MAC_INIT is set");
>
> It is useless to printing this sort of information, let alone using BT_INFO...
Ack.
>
> > + /* Wait until MAC_ACCESS is granted */
> > + err = btintel_pcie_poll_bit(data, CSR_FUNC_CTRL_REG,
> > + CSR_FUNC_CTRL_MAC_ACCESS_STS,
> > + CSR_FUNC_CTRL_MAC_ACCESS_STS,
> > + DEFAULT_MAC_ACCESS_TIMEOUT);
> > + if (err < 0) {
> > + BT_ERR("Failed to start bootloader even after %u ns",
> > + DEFAULT_MAC_ACCESS_TIMEOUT);
> > + return -ENODEV;
> > + }
> > +
> > + /* MAC is ready. Enable BT FUNC */
> > + btintel_pcie_set_reg_bits(data, CSR_FUNC_CTRL_REG,
> > + CSR_FUNC_CTRL_FUNC_ENA |
> > + CSR_FUNC_CTRL_FUNC_INIT);
> > +
> > + reg = btintel_pcie_rd_reg32(data, CSR_FUNC_CTRL_REG);
> > + BT_INFO("After: FUNC_CTRL_REG: 0x%x", reg);
>
> Ditto.
Ack.
>
> > + /* wait for interrupt from the device after booting up to primary
> > + * bootloader.
> > + */
> > + err = wait_event_timeout(data->gp0_wait_q, data->gp0_received,
> > + msecs_to_jiffies(DEFAULT_INTR_TIMEOUT));
> > + if (!err) {
> > + BT_ERR("Failed to receive mac_init interrupt");
> > + return -ETIME;
> > + }
> > +
> > + /* Check cached boot stage is CSR_BOOT_STAGE_ROM(BIT(0)) */
> > + if (~data->boot_stage_cache & CSR_BOOT_STAGE_ROM) {
> > + BT_ERR("Device is not running in rom");
> > + return -ENODEV;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +/* This function handles the MSI-X interrupt for gp0 cause(bit 0 in
> > + * CSR_MSIX_HW_INT_CAUSES) which is sent for boot stage and image
> response.
> > + */
> > +static void btintel_pcie_msix_gp0_handler(struct btintel_pcie_data *data)
> > +{
> > + u32 reg;
> > +
> > + /* This interrupt is for three different causes and it is not easy to
> > + * know what causes the interrupt. So, it compares each register value
> > + * with cached value and update it before it wake up the queue.
> > + */
> > + reg = btintel_pcie_rd_reg32(data, CSR_BOOT_STAGE_REG);
> > + if (reg != data->boot_stage_cache) {
> > + data->boot_stage_cache = reg;
> > +
> > + BT_DBG("Boot Stage updated: 0x%x", reg);
> > + }
> > +
> > + reg = btintel_pcie_rd_reg32(data, CSR_IMG_RESPONSE_REG);
> > + if (reg != data->img_resp_cache) {
> > + data->img_resp_cache = reg;
> > +
> > + BT_DBG("Image Response updated: 0x%x", reg);
> > + }
> > +
> > + BT_DBG("---------- cached GP0 registers ----------");
> > + BT_DBG("Cached Boot Stage Reg: 0x%x", data->boot_stage_cache);
> > + BT_DBG("Cached Image Resp Reg: 0x%x", data->img_resp_cache);
> > +
> > + data->gp0_received = true;
> > +
> > + /* If the boot stage is OP or IML, reset IA and start RX again */
> > + if (data->boot_stage_cache & CSR_BOOT_STAGE_OPFW ||
> > + data->boot_stage_cache & CSR_BOOT_STAGE_IML) {
> > + btintel_pcie_reset_ia(data);
> > + btintel_pcie_start_rx(data);
> > + }
> > +
> > + wake_up(&data->gp0_wait_q);
> > +}
> > +
> > +/* This function handles the MSX-X interrupt for rx queue 0 which is for TX
> > + */
> > +static void btintel_pcie_msix_tx_handle(struct btintel_pcie_data *data)
> > +{
> > + u16 cr_tia, cr_hia;
> > + struct txq *txq;
> > + struct urbd0 *urbd0;
> > +
> > + cr_tia = data->ia.cr_tia[TXQ_NUM];
> > + cr_hia = data->ia.cr_hia[TXQ_NUM];
> > +
> > + BT_DBG("[TXQ] cr_hia=%u cr_tia=%u", cr_hia, cr_tia);
> > +
> > + /* Check CR_TIA and CR_HIA for change */
> > + if (cr_tia == cr_hia) {
> > + BT_ERR("[TXQ] no new CD found");
> > + return;
> > + }
> > +
> > + txq = &data->txq;
> > +
> > + while (cr_tia != cr_hia) {
> > + BT_DBG("[TXQ] wake up tx_wait_q");
> > +
> > + data->tx_wait_done = true;
> > + wake_up(&data->tx_wait_q);
> > +
> > + /* Get URBD0 pointed by cr_tia */
> > + urbd0 = &txq->urbd0s[cr_tia];
> > + ipc_print_urbd0(urbd0, cr_tia);
> > +
> > + /* Make sure the completed TFD index is within the range */
> > + if (urbd0->tfd_index > txq->count) {
> > + BT_ERR("[TXQ] out of range: (0x%x)", urbd0->tfd_index);
> > + return;
> > + }
> > +
> > + /* Increase cr_tia */
> > + cr_tia = (cr_tia + 1) % txq->count;
> > + data->ia.cr_tia[TXQ_NUM] = cr_tia;
> > + ipc_print_ia_ring(&data->ia, TXQ_NUM);
> > + }
> > +}
> > +
> > +static int btintel_pcie_recv_event_intel(struct hci_dev *hdev,
> > + struct sk_buff *skb)
> > +{
> > + if (btintel_test_flag(hdev, INTEL_BOOTLOADER)) {
> > + struct hci_event_hdr *hdr = (void *)skb->data;
> > +
> > + if (skb->len > HCI_EVENT_HDR_SIZE && hdr->evt == 0xff &&
> > + hdr->plen > 0) {
> > + const void *ptr = skb->data + HCI_EVENT_HDR_SIZE + 1;
> > + unsigned int len = skb->len - HCI_EVENT_HDR_SIZE - 1;
> > +
> > + switch (skb->data[2]) {
> > + case 0x02:
> > + /* When switching to the operational firmware
> > + * the device sends a vendor specific event
> > + * indicating that the bootup completed.
> > + */
> > + btintel_bootup(hdev, ptr, len);
> > + break;
> > + case 0x06:
> > + /* When the firmware loading completes the
> > + * device sends out a vendor specific event
> > + * indicating the result of the firmware
> > + * loading.
> > + */
> > + btintel_secure_send_result(hdev, ptr, len);
> > + break;
> > + }
> > + }
> > + }
> > +
> > + return hci_recv_frame(hdev, skb);
> > +}
>
> Replace the above with btintel_recv_event?
Ack.
>
> > +/* Process the received rx data
> > + * It check the frame header to identify the data type and create skb
> > + * and calling HCI API
> > + */
> > +static int btintel_pcie_hci_recv_frame(struct btintel_pcie_data *data,
> > + void *buf, int count)
> > +{
> > + struct hci_dev *hdev = data->hdev;
> > + int ret;
> > + u32 pkt_type;
> > + u16 plen;
> > + struct sk_buff *skb;
> > +
> > + spin_lock(&data->hci_rx_lock);
> > +
> > + /* The first 4 bytes indicates the Intel PCIe specific packet type.
> > + * Read the packet type here before remove it.
> > + */
> > + pkt_type = get_unaligned_le32(buf);
> > + bt_dev_dbg(hdev, "pkt_type=%u count=%d", pkt_type, count);
> > +
> > + buf += BTINTEL_PCIE_HCI_TYPE_LEN;
> > + count -= BTINTEL_PCIE_HCI_TYPE_LEN;
> > +
> > + hdev->stat.byte_rx += count;
> > +
> > + skb = bt_skb_alloc(count, GFP_ATOMIC);
> > + if (!skb) {
> > + bt_dev_err(hdev, "Failed to allocate skb for event");
> > + ret = -ENOMEM;
> > + goto exit_error;
> > + }
> > +
> > + switch (pkt_type) {
> > + case BTINTEL_PCIE_HCI_ACL_PKT:
> > + hci_skb_pkt_type(skb) = HCI_ACLDATA_PKT;
> > + memcpy(skb_put(skb, HCI_ACL_HDR_SIZE), buf,
> HCI_ACL_HDR_SIZE);
> > + plen = hci_acl_hdr(skb)->dlen;
> > + buf += HCI_ACL_HDR_SIZE;
> > + break;
> > + case BTINTEL_PCIE_HCI_SCO_PKT:
> > + hci_skb_pkt_type(skb) = HCI_SCODATA_PKT;
> > + memcpy(skb_put(skb, HCI_SCO_HDR_SIZE), buf,
> HCI_SCO_HDR_SIZE);
> > + plen = hci_sco_hdr(skb)->dlen;
> > + buf += HCI_SCO_HDR_SIZE;
> > + break;
> > + case BTINTEL_PCIE_HCI_EVT_PKT:
> > + hci_skb_pkt_type(skb) = HCI_EVENT_PKT;
> > + memcpy(skb_put(skb, HCI_EVENT_HDR_SIZE), buf,
> > + HCI_EVENT_HDR_SIZE);
> > + plen = hci_event_hdr(skb)->plen;
> > + buf += HCI_EVENT_HDR_SIZE;
> > + break;
> > + default:
> > + ret = -EILSEQ;
> > + kfree_skb(skb);
> > + goto exit_error;
> > + }
> > + memcpy(skb_put(skb, plen), buf, plen);
>
> This is very unsafe, to say the least, since we are not checking if
> buf actually contains all the data since we never seem to use the
> count parameter.
Ack.
>
> > +
> > + if (pkt_type == BTINTEL_PCIE_HCI_EVT_PKT)
> > + ret = btintel_pcie_recv_event_intel(hdev, skb);
> > + else
> > + ret = hci_recv_frame(hdev, skb);
> > +
> > +exit_error:
> > + if (ret)
> > + hdev->stat.err_rx++;
> > +
> > + spin_unlock(&data->hci_rx_lock);
> > +
> > + return ret;
> > +}
>
> Hmm, this doesn't sound quite right compared to the likes of
> h4_recv_buf, are we guaranteed to only receive complete packets for
> example?
Yes. Host receives always complete packets. I will refactor this function to take care of spurious packets.
>
> > +/* RX work queue */
> > +static void btintel_pcie_rx_work(struct work_struct *work)
> > +{
> > + struct btintel_pcie_data *data = container_of(work,
> > + struct btintel_pcie_data, rx_work);
> > + struct sk_buff *skb;
> > + int err;
> > +
> > + /* Process the sk_buf in queue and send to the hci layer */
> > + while ((skb = skb_dequeue(&data->rx_skb_q))) {
> > + err = btintel_pcie_hci_recv_frame(data, skb->data, skb->len);
>
> If the data comes as skb then pass the skb and not just the data, len,
> that way we can actually make use of things like skb_pull_data to
> advance in the buffer, etc.
Ack.
>
> > + if (err) {
> > + BT_ERR("Failed to send received frame: %d", err);
> > + kfree_skb(skb);
> > + }
> > + }
> > +}
> > +
> > +/* create the sk_buff with data and save it to queue and start rx work
> > + */
> > +static int btintel_pcie_submit_rx_work(struct btintel_pcie_data *data, u8
> status,
> > + void *buf)
> > +{
> > + int ret, len;
> > + struct rfh_hdr *rfh_hdr;
> > + struct sk_buff *skb;
> > +
> > + rfh_hdr = (struct rfh_hdr *)buf;
> > + btintel_pcie_hci_dump("RFH HDR", buf, sizeof(*rfh_hdr));
> > +
> > + len = rfh_hdr->packet_len;
> > +
> > + /* Remove RFH header */
> > + buf += sizeof(*rfh_hdr);
> > + btintel_pcie_hci_dump("RX", buf, len);
> > +
> > + /* Create the sk_buf with packet in the buf and save it to sk_buf queue
> > + */
> > + skb = alloc_skb(len, GFP_ATOMIC);
> > + if (!skb) {
> > + ret = -ENOMEM;
> > + goto resubmit;
> > + }
> > +
> > + /* Copy the data to skb */
> > + memcpy(skb_put(skb, len), buf, len);
> > +
> > + /* Save the skb to rx queue */
> > + skb_queue_tail(&data->rx_skb_q, skb);
> > +
> > + /* Calling rx_work queue to process the skb */
> > + queue_work(data->workqueue, &data->rx_work);
> > +
> > +resubmit:
> > + BT_DBG("submit next read request");
> > +
> > + /* submit read */
> > + ret = btintel_pcie_submit_rx(data);
> > +
> > + return ret;
> > +}
> > +
> > +/* This function handles the MSI-X interrupt for rx queue 1 which is for RX
> > + */
> > +static void btintel_pcie_msix_rx_handle(struct btintel_pcie_data *data)
> > +{
> > + u16 cr_hia, cr_tia;
> > + struct rxq *rxq;
> > + struct urbd1 *urbd1;
> > + struct frbd *frbd;
> > + struct data_buf *buf;
> > + int ret;
> > +
> > + cr_hia = data->ia.cr_hia[RXQ_NUM];
> > + cr_tia = data->ia.cr_tia[RXQ_NUM];
> > +
> > + BT_DBG("[RXQ] cr_hia=%u cr_tia=%u", cr_hia, cr_tia);
> > +
> > + /* Check CR_TIA and CR_HIA for change */
> > + if (cr_tia == cr_hia) {
> > + BT_ERR("[RXQ] no new CD found");
> > + return;
> > + }
> > +
> > + rxq = &data->rxq;
> > +
> > + /* The firmware sends multiple CD in a single MSIX and it needs to
> > + * process all received CDs in this interrupt.
> > + */
> > + while (cr_tia != cr_hia) {
> > + /* Get URBD1 pointed by cr_tia */
> > + urbd1 = &rxq->urbd1s[cr_tia];
> > + ipc_print_urbd1(urbd1, cr_tia);
> > +
> > + /* Get FRBD poined by urbd1->frbd_tag */
> > + frbd = &rxq->frbds[urbd1->frbd_tag];
> > +
> > + /* Get buf from FRBD tag */
> > + buf = &rxq->bufs[urbd1->frbd_tag];
> > + if (!buf) {
> > + BT_ERR("[RXQ] failed to get the DMA buffer for %d",
> > + urbd1->frbd_tag);
> > + return;
> > + }
> > +
> > + /* prepare RX work */
> > + ret = btintel_pcie_submit_rx_work(data, urbd1->status,
> > + buf->data);
> > + if (ret) {
> > + BT_ERR("[RXQ] failed to submit rx request");
> > + return;
> > + }
> > +
> > + /* Update cr_tia */
> > + cr_tia = (cr_tia + 1) % rxq->count;
> > + data->ia.cr_tia[RXQ_NUM] = cr_tia;
> > + ipc_print_ia_ring(&data->ia, RXQ_NUM);
> > + }
> > + BT_DBG("[RXQ] completed rx interrupt");
> > +}
> > +
> > +static irqreturn_t btintel_pcie_msix_isr(int irq, void *data)
> > +{
> > + return IRQ_WAKE_THREAD;
> > +}
> > +
> > +static irqreturn_t btintel_pcie_irq_msix_handler(int irq, void *dev_id)
> > +{
> > + struct msix_entry *entry = dev_id;
> > + struct btintel_pcie_data *data = btintel_pcie_get_data(entry);
> > + u32 intr_fh, intr_hw;
> > +
> > + BT_DBG("handling msix(irq=%d dev_id=0x%p)", irq, dev_id);
> > +
> > + spin_lock(&data->irq_lock);
> > + intr_fh = btintel_pcie_rd_reg32(data, CSR_MSIX_FH_INT_CAUSES);
> > + intr_hw = btintel_pcie_rd_reg32(data, CSR_MSIX_HW_INT_CAUSES);
> > +
> > + /* Clear causes registers to avoid being handling the same cause */
> > + btintel_pcie_wr_reg32(data, CSR_MSIX_FH_INT_CAUSES, intr_fh);
> > + btintel_pcie_wr_reg32(data, CSR_MSIX_HW_INT_CAUSES, intr_hw);
> > + spin_unlock(&data->irq_lock);
> > +
> > + BT_DBG("intr_fh=0x%x intr_hw=0x%x", intr_fh, intr_hw);
> > +
> > + if (unlikely(!(intr_fh | intr_hw))) {
> > + BT_DBG("Ignore interrupt, inta == 0");
> > + return IRQ_NONE;
> > + }
> > +
> > + /* This interrupt is triggered by the firmware after updating
> > + * boot_stage register and image_response register
> > + */
> > + if (intr_hw & MSIX_HW_INT_CAUSES_GP0) {
> > + BT_DBG("intr for MSIX_HW_INT_CAUSES_GP0");
> > + btintel_pcie_msix_gp0_handler(data);
> > + }
> > +
> > + /* For TX */
> > + if (intr_fh & MSIX_FH_INT_CAUSES_0) {
> > + BT_DBG("intr for MSIX_FH_INT_CAUSES_0");
> > + btintel_pcie_msix_tx_handle(data);
> > + }
> > +
> > + /* For RX */
> > + if (intr_fh & MSIX_FH_INT_CAUSES_1) {
> > + BT_DBG("intr for MSIX_FH_INT_CAUSES_1");
> > + btintel_pcie_msix_rx_handle(data);
> > + }
> > +
> > + /* TODO: Add handler for other causes */
> > + /*
> > + * Before sending the interrupt the HW disables it to prevent
> > + * a nested interrupt. This is done by writing 1 to the corresponding
> > + * bit in the mask register. After handling the interrupt, it should be
> > + * re-enabled by clearing this bit. This register is defined as
> > + * write 1 clear (W1C) register, meaning that it's being clear
> > + * by writing 1 to the bit.
> > + */
> > + btintel_pcie_wr_reg32(data, CSR_MSIX_AUTOMASK_ST, BIT(entry-
> >entry));
> > +
> > + return IRQ_HANDLED;
> > +}
> > +
> > +/* This function requests the irq for msix and registers the handlers per irq.
> > + * Currently, it requests only 1 irq for all interrupt causes.
> > + */
> > +static int btintel_pcie_setup_irq(struct btintel_pcie_data *data)
> > +{
> > + int err;
> > + int num_irqs, i;
> > +
> > + BT_DBG("Initialize msix_entries...");
> > + for (i = 0; i < MSIX_VEC_MAX; i++) {
> > + data->msix_entries[i].entry = i;
> > + BT_DBG("msix_entries[%d] vector=0x%x entry=0x%x",
> > + i, data->msix_entries[i].vector,
> > + data->msix_entries[i].entry);
> > + }
> > +
> > + num_irqs = pci_enable_msix_range(data->pdev, data->msix_entries,
> > + MSIX_VEC_MIN,
> > + MSIX_VEC_MAX);
> > + if (num_irqs < 0) {
> > + BT_ERR("Failed to enable msix range (%d)", num_irqs);
> > + return num_irqs;
> > + }
> > +
> > + data->alloc_vecs = num_irqs;
> > + data->msix_enabled = 1;
> > + data->def_irq = 0;
> > +
> > + BT_DBG("Returned num_irqs=%d", num_irqs);
> > + for (i = 0; i < num_irqs; i++) {
> > + BT_DBG("msix_entries[%d] vector=0x%x entry=0x%x", i,
> > + data->msix_entries[i].vector,
> > + data->msix_entries[i].entry);
> > + }
> > +
> > + BT_DBG("setup irq handler");
> > + for (i = 0; i < data->alloc_vecs; i++) {
> > + struct msix_entry *msix_entry;
> > +
> > + msix_entry = &data->msix_entries[i];
> > +
> > + err = devm_request_threaded_irq(&data->pdev->dev,
> > + msix_entry->vector,
> > + btintel_pcie_msix_isr,
> > + btintel_pcie_irq_msix_handler,
> > + IRQF_SHARED,
> > + KBUILD_MODNAME,
> > + msix_entry);
> > + if (err) {
> > + BT_ERR("Failed to allocate irq handler (%d)", err);
> > + return err;
> > + }
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +struct btintel_pcie_causes_list {
> > + u32 cause;
> > + u32 mask_reg;
> > + u8 cause_num;
> > +};
> > +
> > +struct btintel_pcie_causes_list causes_list[] = {
> > + { MSIX_FH_INT_CAUSES_0, CSR_MSIX_FH_INT_MASK, 0x00 },
> > + { MSIX_FH_INT_CAUSES_1, CSR_MSIX_FH_INT_MASK, 0x01 },
> > + { MSIX_HW_INT_CAUSES_GP0, CSR_MSIX_HW_INT_MASK, 0x20 },
> > +};
> > +
> > +/* This function configures the interrupt masks for both HW_INT_CAUSES
> and
> > + * FH_INT_CAUSES which are meaningful to us.
> > + *
> > + * After resetting BT function via PCIE FLR or FUNC_CTRL reset, the driver
> > + * need to call this function again to configure it again since the masks
> > + * are reset to 0xFFFFFFFF after reset.
> > + */
> > +static void btintel_pcie_config_msix(struct btintel_pcie_data *data)
> > +{
> > + int i;
> > + int val = data->def_irq | MSIX_NON_AUTO_CLEAR_CAUSE;
> > +
> > + /* Set Non Auto Clear Cause */
> > + for (i = 0; i < ARRAY_SIZE(causes_list); i++) {
> > + btintel_pcie_wr_reg8(data,
> > + CSR_MSIX_IVAR(causes_list[i].cause_num),
> > + val);
> > + btintel_pcie_clr_reg_bits(data,
> > + causes_list[i].mask_reg,
> > + causes_list[i].cause);
> > + }
> > +
> > + /* Save the initial interrupt mask */
> > + data->fh_init_mask = ~btintel_pcie_rd_reg32(data,
> CSR_MSIX_FH_INT_MASK);
> > + data->hw_init_mask = ~btintel_pcie_rd_reg32(data,
> CSR_MSIX_HW_INT_MASK);
> > + BT_DBG("init_mask: fh=0x%x hw=0x%x", data->fh_init_mask,
> > + data->hw_init_mask);
> > +}
> > +
> > +static int btintel_pcie_config_pcie(struct pci_dev *pdev,
> > + struct btintel_pcie_data *data)
> > +{
> > + int err;
> > +
> > + err = pcim_enable_device(pdev);
> > + if (err) {
> > + BT_ERR("Failed to enable pci device (%d)", err);
> > + return err;
> > + }
> > + pci_set_master(pdev);
> > +
> > + /* Setup DMA mask */
> > + BT_DBG("Set DMA_MASK(64)");
> > + err = dma_set_mask_and_coherent(&pdev->dev,
> DMA_BIT_MASK(64));
> > + if (err) {
> > + BT_DBG("Set DMA_MASK(32)");
> > + err = dma_set_mask_and_coherent(&pdev->dev,
> DMA_BIT_MASK(32));
> > + /* Both attempt failed */
> > + if (err) {
> > + BT_ERR("No suitable DMA available");
> > + return err;
> > + }
> > + }
> > +
> > + /* Get BAR to access CSR */
> > + err = pcim_iomap_regions(pdev, BIT(0), KBUILD_MODNAME);
> > + if (err) {
> > + BT_ERR("Failed to get iomap regions (%d)", err);
> > + return err;
> > + }
> > +
> > + data->base_addr = pcim_iomap_table(pdev)[0];
> > + if (!data->base_addr) {
> > + BT_ERR("Failed to get base address");
> > + return -ENODEV;
> > + }
> > +
> > + err = btintel_pcie_setup_irq(data);
> > + if (err) {
> > + BT_ERR("Failed to setup irq for msix");
> > + return err;
> > + }
> > +
> > + /* Configure MSI-X with causes list */
> > + btintel_pcie_config_msix(data);
> > +
> > + return 0;
> > +}
> > +
> > +static void btintel_pcie_init_ci(struct btintel_pcie_data *data,
> > + struct ctx_info *ci)
> > +{
> > + ci->version = 0x1;
> > + ci->size = sizeof(*ci);
> > + ci->config = 0x0000;
> > + ci->addr_cr_hia = data->ia.cr_hia_p_addr;
> > + ci->addr_tr_tia = data->ia.tr_tia_p_addr;
> > + ci->addr_cr_tia = data->ia.cr_tia_p_addr;
> > + ci->addr_tr_hia = data->ia.tr_hia_p_addr;
> > + ci->num_cr_ia = NUM_QUEUES;
> > + ci->num_tr_ia = NUM_QUEUES;
> > + ci->addr_urbdq0 = data->txq.urbd0s_p_addr;
> > + ci->addr_tfdq = data->txq.tfds_p_addr;
> > + ci->num_tfdq = data->txq.count;
> > + ci->num_urbdq0 = data->txq.count;
> > + ci->tfdq_db_vec = TXQ_NUM;
> > + ci->urbdq0_db_vec = TXQ_NUM;
> > + ci->rbd_size = RBD_SIZE_4K;
> > + ci->addr_frbdq = data->rxq.frbds_p_addr;
> > + ci->num_frbdq = data->rxq.count;
> > + ci->frbdq_db_vec = RXQ_NUM;
> > + ci->addr_urbdq1 = data->rxq.urbd1s_p_addr;
> > + ci->num_urbdq1 = data->rxq.count;
> > + ci->urbdq_db_vec = RXQ_NUM;
> > +}
> > +
> > +static void btintel_pcie_free_txq_bufs(struct btintel_pcie_data *data,
> > + struct txq *txq)
> > +{
> > + /* Free data buffers first */
> > + dma_free_coherent(&data->pdev->dev, txq->count * BUFFER_SIZE,
> > + txq->buf_v_addr, txq->buf_p_addr);
> > + kfree(txq->bufs);
> > + BT_DBG("txq buffers are freed");
> > +}
> > +
> > +static int btintel_pcie_setup_txq_bufs(struct btintel_pcie_data *data,
> > + struct txq *txq)
> > +{
> > + int err = 0, i;
> > + struct data_buf *buf;
> > +
> > + if (txq->count == 0) {
> > + BT_ERR("invalid parameter: txq->count");
> > + err = -EINVAL;
> > + goto exit_error;
> > + }
> > +
> > + /* Allocate the same number of buffers as the descriptor */
> > + txq->bufs = kmalloc_array(txq->count, sizeof(*buf), GFP_KERNEL);
> > + if (!txq->bufs) {
> > + err = -ENOMEM;
> > + goto exit_error;
> > + }
> > +
> > + /* Allocate full chunk of data buffer for DMA first and do indexing and
> > + * initialization next, so it can be freed easily
> > + */
> > + txq->buf_v_addr = dma_alloc_coherent(&data->pdev->dev,
> > + txq->count * BUFFER_SIZE,
> > + &txq->buf_p_addr,
> > + GFP_KERNEL | __GFP_NOWARN);
> > + if (!txq->buf_v_addr) {
> > + BT_ERR("Failed to allocate DMA buf");
> > + err = -ENOMEM;
> > + kfree(txq->bufs);
> > + goto exit_error;
> > + }
> > + memset(txq->buf_v_addr, 0, txq->count * BUFFER_SIZE);
> > +
> > + BT_DBG("alloc bufs: p=0x%llx v=0x%p", txq->buf_p_addr, txq-
> >buf_v_addr);
> > +
> > + /* Setup the allocated DMA buffer to bufs. Each data_buf should
> > + * have virtual address and physical address
> > + */
> > + for (i = 0; i < txq->count; i++) {
> > + buf = &txq->bufs[i];
> > + buf->data_p_addr = txq->buf_p_addr + (i * BUFFER_SIZE);
> > + buf->data = txq->buf_v_addr + (i * BUFFER_SIZE);
> > + }
> > +
> > +exit_error:
> > + return err;
> > +}
> > +
> > +static void btintel_pcie_free_rxq_bufs(struct btintel_pcie_data *data,
> > + struct rxq *rxq)
> > +{
> > + /* Free data buffers first */
> > + dma_free_coherent(&data->pdev->dev, rxq->count * BUFFER_SIZE,
> > + rxq->buf_v_addr, rxq->buf_p_addr);
> > + kfree(rxq->bufs);
> > + BT_DBG("rxq buffers are freed");
> > +}
> > +
> > +static int btintel_pcie_setup_rxq_bufs(struct btintel_pcie_data *data,
> > + struct rxq *rxq)
> > +{
> > + int err = 0, i;
> > + struct data_buf *buf;
> > +
> > + if (rxq->count == 0) {
> > + BT_ERR("invalid parameter: rxq->count");
> > + err = -EINVAL;
> > + goto exit_error;
> > + }
> > +
> > + /* Allocate the same number of buffers as the descriptor */
> > + rxq->bufs = kmalloc_array(rxq->count, sizeof(*buf), GFP_KERNEL);
> > + if (!rxq->bufs) {
> > + err = -ENOMEM;
> > + goto exit_error;
> > + }
> > +
> > + /* Allocate full chunk of data buffer for DMA first and do indexing and
> > + * initialization next, so it can be freed easily
> > + */
> > + rxq->buf_v_addr = dma_alloc_coherent(&data->pdev->dev,
> > + rxq->count * BUFFER_SIZE,
> > + &rxq->buf_p_addr,
> > + GFP_KERNEL | __GFP_NOWARN);
> > + if (!rxq->buf_v_addr) {
> > + BT_ERR("Failed to allocate DMA buf");
> > + err = -ENOMEM;
> > + kfree(rxq->bufs);
> > + goto exit_error;
> > + }
> > + memset(rxq->buf_v_addr, 0, rxq->count * BUFFER_SIZE);
> > +
> > + BT_DBG("alloc bufs: p=0x%llx v=0x%p", rxq->buf_p_addr, rxq-
> >buf_v_addr);
> > +
> > + /* Setup the allocated DMA buffer to bufs. Each data_buf should
> > + * have virtual address and physical address
> > + */
> > + for (i = 0; i < rxq->count; i++) {
> > + buf = &rxq->bufs[i];
> > + buf->data_p_addr = rxq->buf_p_addr + (i * BUFFER_SIZE);
> > + buf->data = rxq->buf_v_addr + (i * BUFFER_SIZE);
> > + }
> > +
> > +exit_error:
> > +
> > + return err;
> > +}
> > +
> > +static void btintel_pcie_setup_ia(struct btintel_pcie_data *data,
> > + dma_addr_t p_addr, void *v_addr,
> > + struct ia *ia)
> > +{
> > + /* TR Head Index Array */
> > + ia->tr_hia_p_addr = p_addr;
> > + ia->tr_hia = v_addr;
> > +
> > + /* TR Tail Index Array */
> > + ia->tr_tia_p_addr = p_addr + sizeof(u16) * NUM_QUEUES;
> > + ia->tr_tia = v_addr + sizeof(u16) * NUM_QUEUES;
> > +
> > + /* CR Head index Array */
> > + ia->cr_hia_p_addr = p_addr + (sizeof(u16) * NUM_QUEUES * 2);
> > + ia->cr_hia = v_addr + (sizeof(u16) * NUM_QUEUES * 2);
> > +
> > + /* CR Tail Index Array */
> > + ia->cr_tia_p_addr = p_addr + (sizeof(u16) * NUM_QUEUES * 3);
> > + ia->cr_tia = v_addr + (sizeof(u16) * NUM_QUEUES * 3);
> > +}
> > +
> > +static void btintel_pcie_free(struct btintel_pcie_data *data)
> > +{
> > + btintel_pcie_free_rxq_bufs(data, &data->rxq);
> > + btintel_pcie_free_txq_bufs(data, &data->txq);
> > +
> > + dma_pool_free(data->dma_pool, data->dma_v_addr, data-
> >dma_p_addr);
> > + dma_pool_destroy(data->dma_pool);
> > + BT_DBG("DMA memory is freed");
>
> Printing this kind of information is useless, we should really make
> sure there are no leaks but there are better tools for that then
> printing when we free data.
Ack.
>
> > +}
> > +
> > +/* Allocate tx and rx queues, any related data structures and buffers.
> > + */
> > +static int btintel_pcie_alloc(struct btintel_pcie_data *data)
> > +{
> > + int err = 0;
> > + size_t total;
> > + dma_addr_t p_addr;
> > + void *v_addr;
> > +
> > + /* Allocate the chunk of DMA memory for descriptors, index array, and
> > + * context information, instead of allocating individually.
> > + * The DMA memory for data buffer is allocated while setting up the
> > + * each queue.
> > + *
> > + * Total size is sum of the following
> > + * + size of TFD * Number of descriptors in queue
> > + * + size of URBD0 * Number of descriptors in queue
> > + * + size of FRBD * Number of descriptors in queue
> > + * + size of URBD1 * Number of descriptors in queue
> > + * + size of index * Number of queues(2) * type of index array(4)
> > + * + size of context information
> > + */
> > + total = (sizeof(struct tfd) + sizeof(struct urbd0) + sizeof(struct frbd)
> > + + sizeof(struct urbd1)) * DESCS_COUNT;
> > +
> > + /* Add the sum of size of index array and size of ci struct */
> > + total += (sizeof(u16) * NUM_QUEUES * 4) + sizeof(struct ctx_info);
> > +
> > + /* Allocate DMA Pool */
> > + data->dma_pool = dma_pool_create(KBUILD_MODNAME, &data-
> >pdev->dev,
> > + total, DMA_POOL_ALIGNMENT, 0);
> > + if (!data->dma_pool) {
> > + BT_ERR("Failed to allocate dma pool for queues");
> > + err = -ENOMEM;
> > + goto exit_error;
> > + }
> > +
> > + v_addr = dma_pool_zalloc(data->dma_pool, GFP_KERNEL |
> __GFP_NOWARN,
> > + &p_addr);
> > + if (!v_addr) {
> > + BT_ERR("Failed to alloc dma memory for queues");
> > + dma_pool_destroy(data->dma_pool);
> > + err = -ENOMEM;
> > + goto exit_error;
> > + }
> > +
> > + data->dma_p_addr = p_addr;
> > + data->dma_v_addr = v_addr;
> > +
> > + BT_DBG("dma pool: p_addr=0x%llx v_addr=0x%p", p_addr, v_addr);
> > +
> > + /* Setup descriptor count */
> > + data->txq.count = DESCS_COUNT;
> > + data->rxq.count = DESCS_COUNT;
> > +
> > + /* Setup tfds */
> > + data->txq.tfds_p_addr = p_addr;
> > + data->txq.tfds = v_addr;
> > +
> > + p_addr += (sizeof(struct tfd) * DESCS_COUNT);
> > + v_addr += (sizeof(struct tfd) * DESCS_COUNT);
> > +
> > + /* Setup urbd0 */
> > + data->txq.urbd0s_p_addr = p_addr;
> > + data->txq.urbd0s = v_addr;
> > +
> > + p_addr += (sizeof(struct urbd0) * DESCS_COUNT);
> > + v_addr += (sizeof(struct urbd0) * DESCS_COUNT);
> > +
> > + /* Setup frbd */
> > + data->rxq.frbds_p_addr = p_addr;
> > + data->rxq.frbds = v_addr;
> > +
> > + p_addr += (sizeof(struct frbd) * DESCS_COUNT);
> > + v_addr += (sizeof(struct frbd) * DESCS_COUNT);
> > +
> > + /* Setup urbd1 */
> > + data->rxq.urbd1s_p_addr = p_addr;
> > + data->rxq.urbd1s = v_addr;
> > +
> > + p_addr += (sizeof(struct urbd1) * DESCS_COUNT);
> > + v_addr += (sizeof(struct urbd1) * DESCS_COUNT);
> > +
> > + /* Setup data buffers for txq */
> > + err = btintel_pcie_setup_txq_bufs(data, &data->txq);
> > + if (err) {
> > + BT_ERR("Failed to setup txq buffers: %d", err);
> > + goto exit_error_pool;
> > + }
> > +
> > + /* Setup data buffers for rxq */
> > + err = btintel_pcie_setup_rxq_bufs(data, &data->rxq);
> > + if (err) {
> > + BT_ERR("Failed to allocate rxq buffers: %d", err);
> > + goto exit_error_txq;
> > + }
> > +
> > + /* Setup Index Array */
> > + btintel_pcie_setup_ia(data, p_addr, v_addr, &data->ia);
> > +
> > + /* Setup Context Information */
> > + p_addr += sizeof(u16) * NUM_QUEUES * 4;
> > + v_addr += sizeof(u16) * NUM_QUEUES * 4;
> > +
> > + data->ci = v_addr;
> > + data->ci_p_addr = p_addr;
> > +
> > + /* Initialize the CI */
> > + btintel_pcie_init_ci(data, data->ci);
> > +
> > + return 0;
> > +
> > +exit_error_txq:
> > + btintel_pcie_free_txq_bufs(data, &data->txq);
> > +exit_error_pool:
> > + dma_pool_free(data->dma_pool, data->dma_v_addr, data-
> >dma_p_addr);
> > + dma_pool_destroy(data->dma_pool);
> > +exit_error:
> > + return err;
> > +}
> > +
> > +static void btintel_pcie_release_hdev(struct btintel_pcie_data *data)
> > +{
> > + struct hci_dev *hdev;
> > +
> > + hdev = data->hdev;
> > + if (hdev) {
> > + hci_unregister_dev(hdev);
> > + hci_free_dev(hdev);
> > + }
> > + data->hdev = NULL;
> > +}
> > +
> > +static int btintel_pcie_setup_hdev(struct btintel_pcie_data *data)
> > +{
> > + /* TODO: initialize hdev and assign the callbacks to hdev */
> > + return -ENODEV;
> > +}
> > +
> > +static int btintel_pcie_probe(struct pci_dev *pdev,
> > + const struct pci_device_id *ent)
> > +{
> > + int err;
> > + struct btintel_pcie_data *data;
> > +
> > + if (!pdev)
> > + return -ENODEV;
> > +
> > + data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
> > + if (!data)
> > + return -ENOMEM;
> > +
> > + /* initialize the btintel_pcie data struct */
> > + data->pdev = pdev;
> > +
> > + spin_lock_init(&data->irq_lock);
> > + spin_lock_init(&data->hci_rx_lock);
> > +
> > + init_waitqueue_head(&data->gp0_wait_q);
> > + data->gp0_received = false;
> > +
> > + init_waitqueue_head(&data->tx_wait_q);
> > + data->tx_wait_done = false;
> > +
> > + data->workqueue = alloc_ordered_workqueue(KBUILD_MODNAME,
> WQ_HIGHPRI);
> > + if (!data->workqueue) {
> > + BT_ERR("Failed to create workqueue");
> > + return -ENOMEM;
> > + }
> > + skb_queue_head_init(&data->rx_skb_q);
> > + INIT_WORK(&data->rx_work, btintel_pcie_rx_work);
> > +
> > + data->boot_stage_cache = 0x00;
> > + data->img_resp_cache = 0x00;
> > +
> > + /* PCIe specific all to configure it for this device includes
> > + * enabling pice device, setting master, reading BAR[0], configuring
> > + * MSIx, setting DMA mask, and save the driver data.
> > + */
> > + err = btintel_pcie_config_pcie(pdev, data);
> > + if (err) {
> > + BT_ERR("Failed to config pcie (%d)", err);
> > + goto exit_error;
> > + }
> > +
> > + /* Set driver data for this PCI device */
> > + pci_set_drvdata(pdev, data);
> > +
> > + /* allocate the IPC struct */
> > + err = btintel_pcie_alloc(data);
> > + if (err) {
> > + BT_ERR("Failed to allocate queues(%d)", err);
> > + goto exit_error;
> > + }
> > +
> > + /* Enable BT function */
> > + err = btintel_pcie_enable_bt(data);
> > + if (err) {
> > + BT_ERR("Failed to start bluetooth device(%d)", err);
> > + goto exit_error;
> > + }
> > +
> > + /* CNV information (CNVi and CNVr) is in CSR */
> > + data->cnvi = btintel_pcie_rd_reg32(data, CSR_HW_REV_REG);
> > + BT_DBG("cnvi: 0x%08x", data->cnvi);
> > +
> > + data->cnvr = btintel_pcie_rd_reg32(data, CSR_RF_ID_REG);
> > + BT_DBG("cnvr: 0x%08x", data->cnvr);
> > +
> > + err = btintel_pcie_start_rx(data);
> > + if (err) {
> > + BT_ERR("Failed to start rx (%d)", err);
> > + goto exit_error;
> > + }
> > +
> > + err = btintel_pcie_setup_hdev(data);
> > + if (err) {
> > + BT_ERR("Failed to setup HCI module");
> > + goto exit_error;
> > + }
> > +
> > + return 0;
> > +
> > +exit_error:
> > + /* reset device before leave */
> > + btintel_pcie_reset_bt(data);
> > +
> > + /* clear bus mastering */
> > + pci_clear_master(pdev);
> > +
> > + /* Unset driver data for PCI device */
> > + pci_set_drvdata(pdev, NULL);
> > +
> > + return err;
> > +}
> > +
> > +static void btintel_pcie_remove(struct pci_dev *pdev)
> > +{
> > + struct btintel_pcie_data *data;
> > +
> > + if (!pdev) {
> > + BT_ERR("Invalid parameter: pdev");
> > + return;
> > + }
> > +
> > + data = pci_get_drvdata(pdev);
> > + if (!data) {
> > + BT_ERR("data is empty");
> > + return;
> > + }
> > +
> > + btintel_pcie_release_hdev(data);
> > +
> > + flush_work(&data->rx_work);
> > +
> > + destroy_workqueue(data->workqueue);
> > +
> > + btintel_pcie_free(data);
> > +
> > + /* reset device before leave */
> > + btintel_pcie_reset_bt(data);
> > +
> > + /* clear bus mastering */
> > + pci_clear_master(pdev);
> > +
> > + /* Unset driver data for PCI device */
> > + pci_set_drvdata(pdev, NULL);
> > +}
> > +
> > +#ifdef CONFIG_PM
> > +static int btintel_pcie_suspend(struct device *dev)
> > +{
> > + /* TODO: Add support suspend */
> > + return 0;
> > +}
> > +
> > +static int btintel_pcie_resume(struct device *dev)
> > +{
> > + /* TODO: Add support resume */
> > + return 0;
> > +}
> > +
> > +static SIMPLE_DEV_PM_OPS(btintel_pcie_pm_ops, btintel_pcie_suspend,
> > + btintel_pcie_resume);
> > +#endif /* CONFIG_PM */
> > +
> > +static struct pci_driver btintel_pcie_driver = {
> > + .name = KBUILD_MODNAME,
> > + .id_table = btintel_pcie_table,
> > + .probe = btintel_pcie_probe,
> > + .remove = btintel_pcie_remove,
> > +#ifdef CONFIG_PM
> > + .driver.pm = &btintel_pcie_pm_ops,
> > +#endif /* CONFIG_PM */
> > +};
> > +module_pci_driver(btintel_pcie_driver);
> > +
> > +MODULE_AUTHOR("Tedd Ho-Jeong An <tedd.an@intel.com>");
> > +MODULE_DESCRIPTION("Intel Bluetooth PCIe transport driver ver "
> VERSION);
> > +MODULE_VERSION(VERSION);
> > +MODULE_LICENSE("GPL");
>
> Botton line: We have to tone down the debbuging since it pretting a
> lot of useless information and when it does it prints with old BT_DBG
> macros which doesn't print the controller info so on system with
> multiple controller that would be impossible to say which controller
> is generating the logs.
Ack. I will remove the unwanted debug logs and switch to bt_dev_dbg/info/err wherever applicable.
>
> > diff --git a/drivers/bluetooth/btintel_pcie.h
> b/drivers/bluetooth/btintel_pcie.h
> > new file mode 100644
> > index 000000000000..1554964686bd
> > --- /dev/null
> > +++ b/drivers/bluetooth/btintel_pcie.h
> > @@ -0,0 +1,449 @@
> > +/* SPDX-License-Identifier: GPL-2.0-or-later */
> > +/*
> > + * Intel Bluetooth PCIE driver
> > + *
> > + * Copyright (C) 2017 Intel Corporation. All rights reserved.
>
> Ditto.
>
Ack.
> > + *
> > + * This program is free software; you can redistribute it and/or
> > + * modify it under the terms of the GNU General Public License version
> > + * 2 as published by the Free Software Foundation.
> > + *
> > + * This program is distributed in the hope that it will be useful,
> > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> > + * GNU General Public License for more details.
> > + *
> > + * Copyright (C) 2022 Intel Corporation
> > + *
> > + * Intel Bluetooth Driver for PCIE interface.
> > + */
> > +
> > +/* Control and Status Register(CSR) */
> > +#define CSR_BASE (0x000)
> > +#define CSR_FUNC_CTRL_REG (CSR_BASE + 0x024)
> > +#define CSR_HW_REV_REG (CSR_BASE + 0x028)
> > +#define CSR_RF_ID_REG (CSR_BASE + 0x09C)
> > +#define CSR_BOOT_STAGE_REG (CSR_BASE + 0x108)
> > +#define CSR_CI_ADDR_LSB_REG (CSR_BASE + 0x118)
> > +#define CSR_CI_ADDR_MSB_REG (CSR_BASE + 0x11C)
> > +#define CSR_IMG_RESPONSE_REG (CSR_BASE + 0x12C)
> > +#define CSR_HBUS_TARG_WRPTR (CSR_BASE + 0x460)
> > +
> > +/* CSR Function Control Register */
> > +#define CSR_FUNC_CTRL_FUNC_ENA (BIT(0))
> > +#define CSR_FUNC_CTRL_MAC_INIT (BIT(6))
> > +#define CSR_FUNC_CTRL_FUNC_INIT (BIT(7))
> > +#define CSR_FUNC_CTRL_MAC_ACCESS_STS (BIT(20))
> > +#define CSR_FUNC_CTRL_SW_RESET (BIT(31))
> > +
> > +/* Value for CSR_BOOT_STAGE register */
> > +#define CSR_BOOT_STAGE_ROM (BIT(0))
> > +#define CSR_BOOT_STAGE_IML (BIT(1))
> > +#define CSR_BOOT_STAGE_OPFW (BIT(2))
> > +#define CSR_BOOT_STAGE_ROM_LOCKDOWN (BIT(10))
> > +#define CSR_BOOT_STAGE_IML_LOCKDOWN (BIT(11))
> > +#define CSR_BOOT_STAGE_MAC_ACCESS_ON (BIT(16))
> > +#define CSR_BOOT_STAGE_ALIVE (BIT(23))
> > +
> > +/* Registers for MSIX */
> > +#define CSR_MSIX_BASE (0x2000)
> > +#define CSR_MSIX_FH_INT_CAUSES (CSR_MSIX_BASE + 0x0800)
> > +#define CSR_MSIX_FH_INT_MASK (CSR_MSIX_BASE + 0x0804)
> > +#define CSR_MSIX_HW_INT_CAUSES (CSR_MSIX_BASE + 0x0808)
> > +#define CSR_MSIX_HW_INT_MASK (CSR_MSIX_BASE + 0x080C)
> > +#define CSR_MSIX_AUTOMASK_ST (CSR_MSIX_BASE + 0x0810)
> > +#define CSR_MSIX_AUTOMASK_EN (CSR_MSIX_BASE + 0x0814)
> > +#define CSR_MSIX_IVAR_BASE (CSR_MSIX_BASE + 0x0880)
> > +#define CSR_MSIX_IVAR(cause) (CSR_MSIX_IVAR_BASE + (cause))
> > +
> > +/* Causes for the FH register interrupts */
> > +enum msix_fh_int_causes {
> > + MSIX_FH_INT_CAUSES_0 = BIT(0), /* cause 0 */
> > + MSIX_FH_INT_CAUSES_1 = BIT(1), /* cause 1 */
> > +};
> > +
> > +/* Causes for the HW register interrupts */
> > +enum msix_hw_int_causes {
> > + MSIX_HW_INT_CAUSES_GP0 = BIT(0), /* cause 32 */
> > +};
> > +
> > +#define MSIX_NON_AUTO_CLEAR_CAUSE BIT(7)
> > +
> > +/* Minimum and Maximum number of MSIx Vector
> > + * Intel Bluetooth PCIe support only 1 vector
> > + */
> > +#define MSIX_VEC_MAX 1
> > +#define MSIX_VEC_MIN 1
> > +
> > +/* Default Poll time for MAC access during init*/
> > +#define DEFAULT_MAC_ACCESS_TIMEOUT 200000
> > +
> > +/* Default interrupt timeout in msec */
> > +#define DEFAULT_INTR_TIMEOUT 3000
> > +
> > +/* The number of descriptors in TX/RX queues */
> > +#define DESCS_COUNT 16
> > +
> > +/* Number of Queue for TX and RX
> > + * It indicates the index of the IA(Index Array)
> > + */
> > +enum {
> > + TXQ_NUM = 0,
> > + RXQ_NUM = 1,
> > + NUM_QUEUES = 2,
> > +};
> > +
> > +/* The size of DMA buffer for TX and RX */
> > +#define BUFFER_SIZE 4096
> > +
> > +/* DMA allocation alignment */
> > +#define DMA_POOL_ALIGNMENT 256
> > +
> > +/* TX wait time (jiffies) */
> > +#define TX_WAIT_TIMEOUT 500
> > +
> > +/* Number of pending RX requests for downlink */
> > +#define RX_MAX_QUEUE 6
> > +
> > +/* Enum for RBD buffer size mappting */
> > +enum {
> > + RBD_SIZE_1K = 0x1,
> > + RBD_SIZE_2K = 0x2,
> > + RBD_SIZE_4K = 0x4,
> > + RBD_SIZE_8K = 0x8,
> > + RBD_SIZE_12K = 0x9,
> > + RBD_SIZE_16K = 0xA,
> > + RBD_SIZE_20K = 0xB,
> > + RBD_SIZE_24K = 0xC,
> > + RBD_SIZE_28K = 0xD,
> > + RBD_SIZE_32K = 0xE,
> > +};
> > +
> > +/*
> > + * Struct for Context Information (v2)
> > + *
> > + * All members are write-only for host and read-only for device.
> > + *
> > + * @version: Version of context information
> > + * @size: Size of context information
> > + * @config: Config with which host wants peripheral to execute
> > + * Subset of capability register published by device
> > + * @addr_tr_hia: Address of TR Head Index Array
> > + * @addr_tr_tia: Address of TR Tail Index Array
> > + * @addr_cr_hia: Address of CR Head Index Array
> > + * @addr_cr_tia: Address of CR Tail Index Array
> > + * @num_tr_ia: Number of entries in TR Index Arrays
> > + * @num_cr_ia: Number of entries in CR Index Arrays
> > + * @rbd_siz: RBD Size { 0x4=4K }
> > + * @addr_tfdq: Address of TFD Queue(tx)
> > + * @addr_urbdq0: Address of URBD Queue(tx)
> > + * @num_tfdq: Number of TFD in TFD Queue(tx)
> > + * @num_urbdq0: Number of URBD in URBD Queue(tx)
> > + * @tfdq_db_vec: Queue number of TFD
> > + * @urbdq0_db_vec: Queue number of URBD
> > + * @addr_frbdq: Address of FRBD Queue(rx)
> > + * @addr_urbdq1: Address of URBD Queue(rx)
> > + * @num_frbdq: Number of FRBD in FRBD Queue(rx)
> > + * @frbdq_db_vec: Queue number of FRBD
> > + * @num_urbdq1: Number of URBD in URBD Queue(rx)
> > + * @urbdq_db_vec: Queue number of URBDQ1
> > + * @tr_msi_vec: Transfer Ring MSI Vector
> > + * @cr_msi_vec: Completion Ring MSI Vector
> > + * @dbgc_addr: DBGC first fragmemt address
> > + * @dbgc_size: DBGC buffer size
> > + * @early_enable: Enarly debug enable
> > + * @dbg_output_mode: Debug output mode
> > + * Bit[4] DBGC O/P { 0=SRAM, 1=DRAM(not relevant for NPK) }
> > + * Bit[5] DBGC I/P { 0=BDBG, 1=DBGI }
> > + * Bits[6:7] DBGI O/P(relevant if bit[5] = 1)
> > + * 0=BT DBGC, 1=WiFi DBGC, 2=NPK }
> > + * @dbg_preset: Debug preset
> > + * @ext_addr: Address of context information extension
> > + * @ext_size: Size of context information part
> > + *
> > + * Total 38 DWords
> > + *
> > + */
> > +struct ctx_info {
> > + u16 version;
> > + u16 size;
> > + u32 config;
> > + u32 reserved_dw02;
> > + u32 reserved_dw03;
> > + u64 addr_tr_hia;
> > + u64 addr_tr_tia;
> > + u64 addr_cr_hia;
> > + u64 addr_cr_tia;
> > + u16 num_tr_ia;
> > + u16 num_cr_ia;
> > + u32 rbd_size:4,
> > + reserved_dw13:28;
> > + u64 addr_tfdq;
> > + u64 addr_urbdq0;
> > + u16 num_tfdq;
> > + u16 num_urbdq0;
> > + u16 tfdq_db_vec;
> > + u16 urbdq0_db_vec;
> > + u64 addr_frbdq;
> > + u64 addr_urbdq1;
> > + u16 num_frbdq;
> > + u16 frbdq_db_vec;
> > + u16 num_urbdq1;
> > + u16 urbdq_db_vec;
> > + u16 tr_msi_vec;
> > + u16 cr_msi_vec;
> > + u32 reserved_dw27;
> > + u64 dbgc_addr;
> > + u32 dbgc_size;
> > + u32 early_enable:1,
> > + reserved_dw31:3,
> > + dbg_output_mode:4,
> > + dbg_preset:8,
> > + reserved2_dw31:16;
> > + u64 ext_addr;
> > + u32 ext_size;
> > + u32 test_param;
> > + u32 reserved_dw36;
> > + u32 reserved_dw37;
> > +} __packed;
> > +
> > +/* Transfer Descriptor for TX
> > + * @type: Not in use. Set to 0x0
> > + * @size: Size of data in the buffer
> > + * @addr: DMA Address of buffer
> > + */
> > +struct tfd {
> > + u8 type;
> > + u16 size;
> > + u8 reserved;
> > + u64 addr;
> > + u32 reserved1;
> > +} __packed;
> > +
> > +/* URB Descriptor for TX
> > + * @tfd_index: Index of TFD in TFDQ + 1
> > + * @num_txq: Queue index of TFD Queue
> > + * @cmpl_count: Completion count. Always 0x01
> > + * @immediate_cmpl: Immediate completion flag: Always 0x01
> > + */
> > +struct urbd0 {
> > + u32 tfd_index:16,
> > + num_txq:8,
> > + cmpl_count:4,
> > + reserved:3,
> > + immediate_cmpl:1;
> > +} __packed;
> > +
> > +/* FRB Descriptor for RX
> > + * @tag: RX buffer tag (index of RX buffer queue)
> > + * @addr: Address of buffer
> > + */
> > +struct frbd {
> > + u32 tag:16,
> > + reserved:16;
> > + u32 reserved2;
> > + u64 addr;
> > +} __packed;
> > +
> > +/* URB Descriptor for RX
> > + * @frbd_tag: Tag from FRBD
> > + * @status: Status
> > + */
> > +struct urbd1 {
> > + u32 frbd_tag:16,
> > + status:1,
> > + reserved:14,
> > + fixed:1;
> > +} __packed;
> > +
> > +/* RFH header in RX packet
> > + * @packet_len: Length of the data in the buffer
> > + * @rxq: RX Queue number
> > + * @cmd_id: Command ID. Not in Use
> > + */
> > +struct rfh_hdr {
> > + u64 packet_len:16,
> > + rxq:6,
> > + reserved:10,
> > + cmd_id:16,
> > + reserved1:16;
> > +} __packed;
> > +
> > +/* Internal data buffer
> > + * @data: pointer to the data buffer
> > + * @p_addr: physical address of data buffer
> > + */
> > +struct data_buf {
> > + u8 *data;
> > + dma_addr_t data_p_addr;
> > +};
> > +
> > +/* Index Array */
> > +struct ia {
> > + dma_addr_t tr_hia_p_addr;
> > + u16 *tr_hia;
> > + dma_addr_t tr_tia_p_addr;
> > + u16 *tr_tia;
> > + dma_addr_t cr_hia_p_addr;
> > + u16 *cr_hia;
> > + dma_addr_t cr_tia_p_addr;
> > + u16 *cr_tia;
> > +};
> > +
> > +/* Structure for TX Queue
> > + * @count: Number of descriptors
> > + * @tfds: Array of TFD
> > + * @urbd0s: Array of URBD0
> > + * @buf: Array of data_buf structure
> > + */
> > +struct txq {
> > + u16 count;
> > +
> > + dma_addr_t tfds_p_addr;
> > + struct tfd *tfds;
> > +
> > + dma_addr_t urbd0s_p_addr;
> > + struct urbd0 *urbd0s;
> > +
> > + dma_addr_t buf_p_addr;
> > + void *buf_v_addr;
> > + struct data_buf *bufs;
> > +};
> > +
> > +/* Structure for RX Queue
> > + * @count: Number of descriptors
> > + * @frbds: Array of FRBD
> > + * @urbd1s: Array of URBD1
> > + * @buf: Array of data_buf structure
> > + */
> > +struct rxq {
> > + u16 count;
> > +
> > + dma_addr_t frbds_p_addr;
> > + struct frbd *frbds;
> > +
> > + dma_addr_t urbd1s_p_addr;
> > + struct urbd1 *urbd1s;
> > +
> > + dma_addr_t buf_p_addr;
> > + void *buf_v_addr;
> > + struct data_buf *bufs;
> > +};
> > +
> > +/* struct btintel_pcie_data
> > + * @pdev: pci device
> > + * @hdev: hdev device
> > + * @flags: driver state
> > + * @irq_lock: spinlock for MSIX
> > + * @hci_rx_lock: spinlock for HCI RX flow
> > + * @base_addr: pci base address (from BAR)
> > + * @msix_entries: array of MSIX entries
> > + * @msix_enabled: true if MSIX is enabled;
> > + * @alloc_vecs: number of interrupt vectors allocated
> > + * @def_irq: default irq for all causes
> > + * @fh_init_mask: initial unmasked rxq causes
> > + * @hw_init_mask: initial unmaksed hw causes
> > + * @boot_stage_cache: cached value of boot stage register
> > + * @img_resp_cache: cached value of image response register
> > + * @cnvi: CNVi register value
> > + * @cnvr: CNVr register value
> > + * @gp0_received: condition for gp0 interrupt
> > + * @gp0_wait_q: wait_q for gp0 interrupt
> > + * @tx_wait_done: condition for tx interrupt
> > + * @tx_wait_q: wait_q for tx interrupt
> > + * @workqueue: workqueue for RX work
> > + * @rx_skb_q: SKB queue for RX packet
> > + * @rx_work: RX work struct to process the RX packet in @rx_skb_q
> > + * @dma_pool: DMA pool for descriptors, index array and ci
> > + * @dma_p_addr: DMA address for pool
> > + * @dma_v_addr: address of pool
> > + * @ci_p_addr: DMA address for CI struct
> > + * @ci: CI struct
> > + * @ia: Index Array struct
> > + * @txq: TX Queue struct
> > + * @rxq: RX Queue struct
> > + */
> > +struct btintel_pcie_data {
> > + struct pci_dev *pdev;
> > + struct hci_dev *hdev;
> > +
> > + unsigned long flags;
> > + /* lock used in MSIX interrupt */
> > + spinlock_t irq_lock;
> > + /* lock to serialize rx events */
> > + spinlock_t hci_rx_lock;
> > +
> > + void __iomem *base_addr;
> > +
> > + struct msix_entry msix_entries[MSIX_VEC_MAX];
> > + bool msix_enabled;
> > + u32 alloc_vecs;
> > + u32 def_irq;
> > +
> > + u32 fh_init_mask;
> > + u32 hw_init_mask;
> > +
> > + u32 boot_stage_cache;
> > + u32 img_resp_cache;
> > +
> > + u32 cnvi;
> > + u32 cnvr;
> > +
> > + bool gp0_received;
> > + wait_queue_head_t gp0_wait_q;
> > +
> > + bool tx_wait_done;
> > + wait_queue_head_t tx_wait_q;
> > +
> > + struct workqueue_struct *workqueue;
> > + struct sk_buff_head rx_skb_q;
> > + struct work_struct rx_work;
> > +
> > + struct dma_pool *dma_pool;
> > + dma_addr_t dma_p_addr;
> > + void *dma_v_addr;
> > +
> > + dma_addr_t ci_p_addr;
> > + struct ctx_info *ci;
> > + struct ia ia;
> > + struct txq txq;
> > + struct rxq rxq;
> > +};
> > +
> > +static inline u32 btintel_pcie_rd_reg32(struct btintel_pcie_data *data,
> > + u32 offset)
> > +{
> > + return ioread32(data->base_addr + offset);
> > +}
> > +
> > +static inline void btintel_pcie_wr_reg8(struct btintel_pcie_data *data,
> > + u32 offset, u8 val)
> > +{
> > + iowrite8(val, data->base_addr + offset);
> > +}
> > +
> > +static inline void btintel_pcie_wr_reg32(struct btintel_pcie_data *data,
> > + u32 offset, u32 val)
> > +{
> > + iowrite32(val, data->base_addr + offset);
> > +}
> > +
> > +static inline void btintel_pcie_set_reg_bits(struct btintel_pcie_data *data,
> > + u32 offset, u32 bits)
> > +{
> > + u32 r;
> > +
> > + r = ioread32(data->base_addr + offset);
> > + r |= bits;
> > + iowrite32(r, data->base_addr + offset);
> > +}
> > +
> > +static inline void btintel_pcie_clr_reg_bits(struct btintel_pcie_data *data,
> > + u32 offset, u32 bits)
> > +{
> > + u32 r;
> > +
> > + r = ioread32(data->base_addr + offset);
> > + r &= ~bits;
> > + iowrite32(r, data->base_addr + offset);
> > +}
> > --
> > 2.34.1
>
> All symbols must be properly prefixed with BTINTEL_PCIE
Ack.
>
> >
>
>
> --
> Luiz Augusto von Dentz
Thanks,
Kiran
^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH v1 2/3] Bluetooth: btintel_pcie: Add support for PCIE transport
2024-03-28 11:19 ` [PATCH v1 2/3] Bluetooth: btintel_pcie: Add support for PCIE transport Kiran K
2024-03-28 12:24 ` Paul Menzel
2024-03-28 14:09 ` Luiz Augusto von Dentz
@ 2024-03-28 17:08 ` Bjorn Helgaas
2024-05-07 13:47 ` K, Kiran
2 siblings, 1 reply; 16+ messages in thread
From: Bjorn Helgaas @ 2024-03-28 17:08 UTC (permalink / raw)
To: Kiran K
Cc: linux-bluetooth, ravishankar.srivatsa, chethan.tumkur.narayan,
Tedd Ho-Jeong An
On Thu, Mar 28, 2024 at 04:49:03PM +0530, Kiran K wrote:
> From: Tedd Ho-Jeong An <tedd.an@intel.com>
>
> Add initial code to support Intel bluetooth devices based on PICE
> transport. This patch allocates memory for buffers, internal structures,
> initializes interrupts for TX & RX and initializes PCIE device.
s/PCIE/PCIe/ (subject, commit log, throughout)
s/PICE/PCIe/ (commit log typo)
s/This patch allocates/Allocate/
s/initializes/initialize/ (twice)
> +#if BTITNEL_PCIE_ENABLE_HCI_DUMP
> +static inline void btintel_pcie_hci_dump(const char *p, const void *b, int s)
> +{
> + const unsigned char *ptr = (const unsigned char *)b;
> + char str[64];
> + int c, i;
> +
> + for (i = c = 0; c < s; c++) {
> + i += snprintf(str + i, sizeof(str) - i, "%02x ", ptr[c]);
> + if ((c > 0 && (c + 1) % 8 == 0) || (c == s - 1)) {
> + BT_DBG("%s: %s", p, str);
> + i = 0;
> + }
> + }
Maybe print_hex_dump() or similar would save you some work here?
> +/* Poll internal in microseconds */
s/internal/interval/
> +#define POLL_INTERVAL 10
I think it's nice when the name of a timeout or interval includes the
units, e.g., POLL_INTERVAL_US.
> +/* Set the doorbell for RXQ to notify the device that @index(actually index-1)
> + * is available to receive the data
Typical style is to add a space before the opening paren in English
text (many occurrences).
> +static void btintel_pcie_set_rx_db(struct btintel_pcie_data *data, u16 index)
> +{
> + u32 val;
> +
> + val = index;
> + val |= (513 << 16);
Where does 513 come from? Maybe a #define or explanatory comment?
> +static void btintel_pcie_prepare_rx(struct rxq *rxq, u16 frbd_index)
> +{
> + struct data_buf *buf;
> + struct frbd *frbd;
> +
> + /* Get the buffer of the frbd for DMA */
s/frbd/FRBD/ for consistency (several occurrences).
> +static void btintel_pcie_rx_work(struct work_struct *work)
> +{
> + struct btintel_pcie_data *data = container_of(work,
> + struct btintel_pcie_data, rx_work);
> + struct sk_buff *skb;
> + int err;
> +
> + /* Process the sk_buf in queue and send to the hci layer */
s/hci/HCI/ for consistency.
> +/* create the sk_buff with data and save it to queue and start rx work
> + */
> +static int btintel_pcie_submit_rx_work(struct btintel_pcie_data *data, u8 status,
> + void *buf)
Comment would fit on one line.
There's a random mix of "rx" vs "RX" in comments, would be nice to be
consistent.
> +static void btintel_pcie_msix_rx_handle(struct btintel_pcie_data *data)
> +{
> + u16 cr_hia, cr_tia;
> + struct rxq *rxq;
> + struct urbd1 *urbd1;
> + struct frbd *frbd;
> + struct data_buf *buf;
> + int ret;
> +
> + cr_hia = data->ia.cr_hia[RXQ_NUM];
> + cr_tia = data->ia.cr_tia[RXQ_NUM];
> +
> + BT_DBG("[RXQ] cr_hia=%u cr_tia=%u", cr_hia, cr_tia);
> +
> + /* Check CR_TIA and CR_HIA for change */
> + if (cr_tia == cr_hia) {
> + BT_ERR("[RXQ] no new CD found");
> + return;
> + }
> +
> + rxq = &data->rxq;
> +
> + /* The firmware sends multiple CD in a single MSIX and it needs to
> + * process all received CDs in this interrupt.
> + */
> + while (cr_tia != cr_hia) {
> + /* Get URBD1 pointed by cr_tia */
> + urbd1 = &rxq->urbd1s[cr_tia];
> + ipc_print_urbd1(urbd1, cr_tia);
> +
> + /* Get FRBD poined by urbd1->frbd_tag */
s/poined/pointed to/ ?
> + * Before sending the interrupt the HW disables it to prevent
> + * a nested interrupt. This is done by writing 1 to the corresponding
> + * bit in the mask register. After handling the interrupt, it should be
> + * re-enabled by clearing this bit. This register is defined as
> + * write 1 clear (W1C) register, meaning that it's being clear
> + * by writing 1 to the bit.
s/being clear/cleared/
> + num_irqs = pci_enable_msix_range(data->pdev, data->msix_entries,
> + MSIX_VEC_MIN,
> + MSIX_VEC_MAX);
pci_enable_msix_range() is deprecated; consider
pci_alloc_irq_vectors() instead.
> +static int btintel_pcie_config_pcie(struct pci_dev *pdev,
> + struct btintel_pcie_data *data)
> +{
> + int err;
> +
> + err = pcim_enable_device(pdev);
> + if (err) {
> + BT_ERR("Failed to enable pci device (%d)", err);
> + return err;
> + }
> + pci_set_master(pdev);
> +
> + /* Setup DMA mask */
Superfluous comment.
> + BT_DBG("Set DMA_MASK(64)");
> + err = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64));
> + if (err) {
> + BT_DBG("Set DMA_MASK(32)");
> + err = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(32));
> + /* Both attempt failed */
> + if (err) {
> + BT_ERR("No suitable DMA available");
> + return err;
> + }
> + }
> +
> + /* Get BAR to access CSR */
Superfluous.
> + err = pcim_iomap_regions(pdev, BIT(0), KBUILD_MODNAME);
> + if (err) {
> + BT_ERR("Failed to get iomap regions (%d)", err);
> + return err;
> + }
> +
> + data->base_addr = pcim_iomap_table(pdev)[0];
> + if (!data->base_addr) {
> + BT_ERR("Failed to get base address");
> + return -ENODEV;
> + }
> +
> + err = btintel_pcie_setup_irq(data);
> + if (err) {
> + BT_ERR("Failed to setup irq for msix");
> + return err;
> + }
> +
> + /* Configure MSI-X with causes list */
Random mix of "MSIX" and "MSI-X". I think "MSI-X" is nicer.
> +static int btintel_pcie_setup_txq_bufs(struct btintel_pcie_data *data,
> + struct txq *txq)
> +{
> + int err = 0, i;
> + struct data_buf *buf;
> +
> + if (txq->count == 0) {
> + BT_ERR("invalid parameter: txq->count");
> + err = -EINVAL;
> + goto exit_error;
You do all the cleanup inline, so there's really no benefit to "err"
and the "exit_error" label. You could "return -EINVAL" directly here
and similar below.
> + }
> +
> + /* Allocate the same number of buffers as the descriptor */
> + txq->bufs = kmalloc_array(txq->count, sizeof(*buf), GFP_KERNEL);
> + if (!txq->bufs) {
> + err = -ENOMEM;
> + goto exit_error;
> + }
> +
> + /* Allocate full chunk of data buffer for DMA first and do indexing and
> + * initialization next, so it can be freed easily
> + */
> + txq->buf_v_addr = dma_alloc_coherent(&data->pdev->dev,
> + txq->count * BUFFER_SIZE,
> + &txq->buf_p_addr,
> + GFP_KERNEL | __GFP_NOWARN);
> + if (!txq->buf_v_addr) {
> + BT_ERR("Failed to allocate DMA buf");
> + err = -ENOMEM;
> + kfree(txq->bufs);
> + goto exit_error;
> + }
> + memset(txq->buf_v_addr, 0, txq->count * BUFFER_SIZE);
> +
> + BT_DBG("alloc bufs: p=0x%llx v=0x%p", txq->buf_p_addr, txq->buf_v_addr);
> +
> + /* Setup the allocated DMA buffer to bufs. Each data_buf should
> + * have virtual address and physical address
> + */
> + for (i = 0; i < txq->count; i++) {
> + buf = &txq->bufs[i];
> + buf->data_p_addr = txq->buf_p_addr + (i * BUFFER_SIZE);
> + buf->data = txq->buf_v_addr + (i * BUFFER_SIZE);
> + }
> +
> +exit_error:
> + return err;
> +}
> +static int btintel_pcie_setup_rxq_bufs(struct btintel_pcie_data *data,
> + struct rxq *rxq)
> +{
> + int err = 0, i;
> + struct data_buf *buf;
> +
> + if (rxq->count == 0) {
> + BT_ERR("invalid parameter: rxq->count");
> + err = -EINVAL;
> + goto exit_error;
Same "err", "exit_error" comment.
> + }
> +
> + /* Allocate the same number of buffers as the descriptor */
> + rxq->bufs = kmalloc_array(rxq->count, sizeof(*buf), GFP_KERNEL);
> + if (!rxq->bufs) {
> + err = -ENOMEM;
> + goto exit_error;
> + }
> +
> + /* Allocate full chunk of data buffer for DMA first and do indexing and
> + * initialization next, so it can be freed easily
> + */
> + rxq->buf_v_addr = dma_alloc_coherent(&data->pdev->dev,
> + rxq->count * BUFFER_SIZE,
> + &rxq->buf_p_addr,
> + GFP_KERNEL | __GFP_NOWARN);
> + if (!rxq->buf_v_addr) {
> + BT_ERR("Failed to allocate DMA buf");
> + err = -ENOMEM;
> + kfree(rxq->bufs);
> + goto exit_error;
> + }
> + memset(rxq->buf_v_addr, 0, rxq->count * BUFFER_SIZE);
> +
> + BT_DBG("alloc bufs: p=0x%llx v=0x%p", rxq->buf_p_addr, rxq->buf_v_addr);
> +
> + /* Setup the allocated DMA buffer to bufs. Each data_buf should
> + * have virtual address and physical address
> + */
> + for (i = 0; i < rxq->count; i++) {
> + buf = &rxq->bufs[i];
> + buf->data_p_addr = rxq->buf_p_addr + (i * BUFFER_SIZE);
> + buf->data = rxq->buf_v_addr + (i * BUFFER_SIZE);
> + }
> +
> +exit_error:
> +
> + return err;
> +}
> +static void btintel_pcie_release_hdev(struct btintel_pcie_data *data)
> +{
> + struct hci_dev *hdev;
> +
> + hdev = data->hdev;
> + if (hdev) {
This test shouldn't be necessary if the driver is written correctly.
We should never get here unless .probe() was successful.
> + hci_unregister_dev(hdev);
There should be a corresponding hci_register_dev(). Since that's not
here yet, I don't think the hci_unregister_dev() should be in this
patch either. Looks like maybe just incomplete code?
Oh, I see hci_register_dev() is added in patch 3/3. They should be
added in the same patch.
> + hci_free_dev(hdev);
> + }
> + data->hdev = NULL;
> +}
> +static int btintel_pcie_probe(struct pci_dev *pdev,
> + const struct pci_device_id *ent)
> +{
> + int err;
> + struct btintel_pcie_data *data;
> +
> + if (!pdev)
> + return -ENODEV;
> +
> + data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
> + if (!data)
> + return -ENOMEM;
> +
> + /* initialize the btintel_pcie data struct */
Superfluous comment.
> + data->pdev = pdev;
> +
> + spin_lock_init(&data->irq_lock);
> + spin_lock_init(&data->hci_rx_lock);
> +
> + init_waitqueue_head(&data->gp0_wait_q);
> + data->gp0_received = false;
> +
> + init_waitqueue_head(&data->tx_wait_q);
> + data->tx_wait_done = false;
> +
> + data->workqueue = alloc_ordered_workqueue(KBUILD_MODNAME, WQ_HIGHPRI);
> + if (!data->workqueue) {
> + BT_ERR("Failed to create workqueue");
> + return -ENOMEM;
> + }
> + skb_queue_head_init(&data->rx_skb_q);
> + INIT_WORK(&data->rx_work, btintel_pcie_rx_work);
> +
> + data->boot_stage_cache = 0x00;
> + data->img_resp_cache = 0x00;
> +
> + /* PCIe specific all to configure it for this device includes
> + * enabling pice device, setting master, reading BAR[0], configuring
> + * MSIx, setting DMA mask, and save the driver data.
s/pice/PCIe/
s/MSIx/MSI-X/
s/save the/saving the/
Whole comment is probably superfluous since this is common to all PCI
drivers.
> + */
> + err = btintel_pcie_config_pcie(pdev, data);
> + if (err) {
> + BT_ERR("Failed to config pcie (%d)", err);
> + goto exit_error;
> + }
> +
> + /* Set driver data for this PCI device */
Superfluous comment.
> + pci_set_drvdata(pdev, data);
> +
> + /* allocate the IPC struct */
> + err = btintel_pcie_alloc(data);
> + if (err) {
> + BT_ERR("Failed to allocate queues(%d)", err);
> + goto exit_error;
> + }
> +
> + /* Enable BT function */
Superfluous comment.
> + err = btintel_pcie_enable_bt(data);
> + if (err) {
> + BT_ERR("Failed to start bluetooth device(%d)", err);
> + goto exit_error;
> + }
> +
> + /* CNV information (CNVi and CNVr) is in CSR */
> + data->cnvi = btintel_pcie_rd_reg32(data, CSR_HW_REV_REG);
> + BT_DBG("cnvi: 0x%08x", data->cnvi);
> +
> + data->cnvr = btintel_pcie_rd_reg32(data, CSR_RF_ID_REG);
> + BT_DBG("cnvr: 0x%08x", data->cnvr);
> +
> + err = btintel_pcie_start_rx(data);
> + if (err) {
> + BT_ERR("Failed to start rx (%d)", err);
> + goto exit_error;
> + }
> +
> + err = btintel_pcie_setup_hdev(data);
> + if (err) {
> + BT_ERR("Failed to setup HCI module");
> + goto exit_error;
> + }
> +
> + return 0;
> +
> +exit_error:
> + /* reset device before leave */
> + btintel_pcie_reset_bt(data);
> +
> + /* clear bus mastering */
Superfluous comment.
> + pci_clear_master(pdev);
> +
> + /* Unset driver data for PCI device */
Superfluous comment.
> + pci_set_drvdata(pdev, NULL);
> +
> + return err;
> +}
> +
> +static void btintel_pcie_remove(struct pci_dev *pdev)
> +{
> + struct btintel_pcie_data *data;
> +
> + if (!pdev) {
Shouldn't need this check. If you get here with "pdev == NULL", the
driver did something wrong and it's better to oops so the driver can
be fixed.
> + BT_ERR("Invalid parameter: pdev");
> + return;
> + }
> +
> + data = pci_get_drvdata(pdev);
> + if (!data) {
Or this one.
> + BT_ERR("data is empty");
> + return;
> + }
> +
> + btintel_pcie_release_hdev(data);
> +
> + flush_work(&data->rx_work);
> +
> + destroy_workqueue(data->workqueue);
> +
> + btintel_pcie_free(data);
> +
> + /* reset device before leave */
> + btintel_pcie_reset_bt(data);
> +
> + /* clear bus mastering */
Superfluous comment.
> + pci_clear_master(pdev);
> +
> + /* Unset driver data for PCI device */
Superfluous comment.
> + pci_set_drvdata(pdev, NULL);
> +}
> +
> +#ifdef CONFIG_PM
> +static int btintel_pcie_suspend(struct device *dev)
> +{
> + /* TODO: Add support suspend */
> + return 0;
> +}
> +
> +static int btintel_pcie_resume(struct device *dev)
> +{
> + /* TODO: Add support resume */
> + return 0;
> +}
> +
> +static SIMPLE_DEV_PM_OPS(btintel_pcie_pm_ops, btintel_pcie_suspend,
> + btintel_pcie_resume);
> +#endif /* CONFIG_PM */
Seems pointless to include this #ifdef CONFIG_PM code until you
implement it.
> +static struct pci_driver btintel_pcie_driver = {
> + .name = KBUILD_MODNAME,
> + .id_table = btintel_pcie_table,
> + .probe = btintel_pcie_probe,
> + .remove = btintel_pcie_remove,
> +#ifdef CONFIG_PM
> + .driver.pm = &btintel_pcie_pm_ops,
> +#endif /* CONFIG_PM */
> +};
> +/* Default Poll time for MAC access during init*/
> +#define DEFAULT_MAC_ACCESS_TIMEOUT 200000
Would be nice to have units here in the name (us, ms, etc).
> +/* Default interrupt timeout in msec */
> +#define DEFAULT_INTR_TIMEOUT 3000
And here.
> +/* Enum for RBD buffer size mappting */
s/mappting/mapping/ ?
> + * @dbgc_addr: DBGC first fragmemt address
> + * @dbgc_size: DBGC buffer size
> + * @early_enable: Enarly debug enable
s/fragmemt/fragment/
s/Enarly/Early/
> + * @dbg_output_mode: Debug output mode
> + * Bit[4] DBGC O/P { 0=SRAM, 1=DRAM(not relevant for NPK) }
> + * Bit[5] DBGC I/P { 0=BDBG, 1=DBGI }
> + * Bits[6:7] DBGI O/P(relevant if bit[5] = 1)
> + * 0=BT DBGC, 1=WiFi DBGC, 2=NPK }
> + * @dbg_preset: Debug preset
> + * @ext_addr: Address of context information extension
> + * @ext_size: Size of context information part
> + *
> + * Total 38 DWords
> + *
Superfluous blank line
> + */
Bjorn
^ permalink raw reply [flat|nested] 16+ messages in thread* RE: [PATCH v1 2/3] Bluetooth: btintel_pcie: Add support for PCIE transport
2024-03-28 17:08 ` Bjorn Helgaas
@ 2024-05-07 13:47 ` K, Kiran
0 siblings, 0 replies; 16+ messages in thread
From: K, Kiran @ 2024-05-07 13:47 UTC (permalink / raw)
To: Bjorn Helgaas
Cc: linux-bluetooth@vger.kernel.org, Srivatsa, Ravishankar,
Tumkur Narayan, Chethan, An, Tedd
Hi Bjron,
Thanks for your comments.
> -----Original Message-----
> From: Bjorn Helgaas <helgaas@kernel.org>
> Sent: Thursday, March 28, 2024 10:38 PM
> To: K, Kiran <kiran.k@intel.com>
> Cc: linux-bluetooth@vger.kernel.org; Srivatsa, Ravishankar
> <ravishankar.srivatsa@intel.com>; Tumkur Narayan, Chethan
> <chethan.tumkur.narayan@intel.com>; An, Tedd <tedd.an@intel.com>
> Subject: Re: [PATCH v1 2/3] Bluetooth: btintel_pcie: Add support for PCIE
> transport
>
> On Thu, Mar 28, 2024 at 04:49:03PM +0530, Kiran K wrote:
> > From: Tedd Ho-Jeong An <tedd.an@intel.com>
> >
> > Add initial code to support Intel bluetooth devices based on PICE
> > transport. This patch allocates memory for buffers, internal
> > structures, initializes interrupts for TX & RX and initializes PCIE device.
>
> s/PCIE/PCIe/ (subject, commit log, throughout) s/PICE/PCIe/ (commit log
> typo) s/This patch allocates/Allocate/ s/initializes/initialize/ (twice)
>
> > +#if BTITNEL_PCIE_ENABLE_HCI_DUMP
> > +static inline void btintel_pcie_hci_dump(const char *p, const void
> > +*b, int s) {
> > + const unsigned char *ptr = (const unsigned char *)b;
> > + char str[64];
> > + int c, i;
> > +
> > + for (i = c = 0; c < s; c++) {
> > + i += snprintf(str + i, sizeof(str) - i, "%02x ", ptr[c]);
> > + if ((c > 0 && (c + 1) % 8 == 0) || (c == s - 1)) {
> > + BT_DBG("%s: %s", p, str);
> > + i = 0;
> > + }
> > + }
>
> Maybe print_hex_dump() or similar would save you some work here?
I will remove this function as we have monitor to dump all the HCI traffic.
>
> > +/* Poll internal in microseconds */
>
> s/internal/interval/
>
> > +#define POLL_INTERVAL 10
>
> I think it's nice when the name of a timeout or interval includes the units, e.g.,
> POLL_INTERVAL_US.
Ack.
>
> > +/* Set the doorbell for RXQ to notify the device that @index(actually
> > +index-1)
> > + * is available to receive the data
>
> Typical style is to add a space before the opening paren in English text (many
> occurrences).
Ack.
>
> > +static void btintel_pcie_set_rx_db(struct btintel_pcie_data *data,
> > +u16 index) {
> > + u32 val;
> > +
> > + val = index;
> > + val |= (513 << 16);
>
> Where does 513 come from? Maybe a #define or explanatory comment?
Its specific to hardware. I will define a macro for the same.
>
> > +static void btintel_pcie_prepare_rx(struct rxq *rxq, u16 frbd_index)
> > +{
> > + struct data_buf *buf;
> > + struct frbd *frbd;
> > +
> > + /* Get the buffer of the frbd for DMA */
>
> s/frbd/FRBD/ for consistency (several occurrences).
Ack.
>
> > +static void btintel_pcie_rx_work(struct work_struct *work) {
> > + struct btintel_pcie_data *data = container_of(work,
> > + struct btintel_pcie_data, rx_work);
> > + struct sk_buff *skb;
> > + int err;
> > +
> > + /* Process the sk_buf in queue and send to the hci layer */
>
> s/hci/HCI/ for consistency.
Ack.
>
> > +/* create the sk_buff with data and save it to queue and start rx
> > +work */ static int btintel_pcie_submit_rx_work(struct
> > +btintel_pcie_data *data, u8 status,
> > + void *buf)
>
> Comment would fit on one line.
>
> There's a random mix of "rx" vs "RX" in comments, would be nice to be
> consistent.
>
Ack.
> > +static void btintel_pcie_msix_rx_handle(struct btintel_pcie_data
> > +*data) {
> > + u16 cr_hia, cr_tia;
> > + struct rxq *rxq;
> > + struct urbd1 *urbd1;
> > + struct frbd *frbd;
> > + struct data_buf *buf;
> > + int ret;
> > +
> > + cr_hia = data->ia.cr_hia[RXQ_NUM];
> > + cr_tia = data->ia.cr_tia[RXQ_NUM];
> > +
> > + BT_DBG("[RXQ] cr_hia=%u cr_tia=%u", cr_hia, cr_tia);
> > +
> > + /* Check CR_TIA and CR_HIA for change */
> > + if (cr_tia == cr_hia) {
> > + BT_ERR("[RXQ] no new CD found");
> > + return;
> > + }
> > +
> > + rxq = &data->rxq;
> > +
> > + /* The firmware sends multiple CD in a single MSIX and it needs to
> > + * process all received CDs in this interrupt.
> > + */
> > + while (cr_tia != cr_hia) {
> > + /* Get URBD1 pointed by cr_tia */
> > + urbd1 = &rxq->urbd1s[cr_tia];
> > + ipc_print_urbd1(urbd1, cr_tia);
> > +
> > + /* Get FRBD poined by urbd1->frbd_tag */
>
> s/poined/pointed to/ ?
Ack. I will remove the comment as its related to handing ring buffer indices.
>
> > + * Before sending the interrupt the HW disables it to prevent
> > + * a nested interrupt. This is done by writing 1 to the corresponding
> > + * bit in the mask register. After handling the interrupt, it should be
> > + * re-enabled by clearing this bit. This register is defined as
> > + * write 1 clear (W1C) register, meaning that it's being clear
> > + * by writing 1 to the bit.
>
> s/being clear/cleared/
Ack.
>
> > + num_irqs = pci_enable_msix_range(data->pdev, data->msix_entries,
> > + MSIX_VEC_MIN,
> > + MSIX_VEC_MAX);
>
> pci_enable_msix_range() is deprecated; consider
> pci_alloc_irq_vectors() instead.
Ack.
>
> > +static int btintel_pcie_config_pcie(struct pci_dev *pdev,
> > + struct btintel_pcie_data *data) {
> > + int err;
> > +
> > + err = pcim_enable_device(pdev);
> > + if (err) {
> > + BT_ERR("Failed to enable pci device (%d)", err);
> > + return err;
> > + }
> > + pci_set_master(pdev);
> > +
> > + /* Setup DMA mask */
>
> Superfluous comment.
Ack. I will remove all these type of obvious comments.
>
> > + BT_DBG("Set DMA_MASK(64)");
> > + err = dma_set_mask_and_coherent(&pdev->dev,
> DMA_BIT_MASK(64));
> > + if (err) {
> > + BT_DBG("Set DMA_MASK(32)");
> > + err = dma_set_mask_and_coherent(&pdev->dev,
> DMA_BIT_MASK(32));
> > + /* Both attempt failed */
> > + if (err) {
> > + BT_ERR("No suitable DMA available");
> > + return err;
> > + }
> > + }
> > +
> > + /* Get BAR to access CSR */
>
> Superfluous.
>
> > + err = pcim_iomap_regions(pdev, BIT(0), KBUILD_MODNAME);
> > + if (err) {
> > + BT_ERR("Failed to get iomap regions (%d)", err);
> > + return err;
> > + }
> > +
> > + data->base_addr = pcim_iomap_table(pdev)[0];
> > + if (!data->base_addr) {
> > + BT_ERR("Failed to get base address");
> > + return -ENODEV;
> > + }
> > +
> > + err = btintel_pcie_setup_irq(data);
> > + if (err) {
> > + BT_ERR("Failed to setup irq for msix");
> > + return err;
> > + }
> > +
> > + /* Configure MSI-X with causes list */
>
> Random mix of "MSIX" and "MSI-X". I think "MSI-X" is nicer.
Ack.
>
> > +static int btintel_pcie_setup_txq_bufs(struct btintel_pcie_data *data,
> > + struct txq *txq)
> > +{
> > + int err = 0, i;
> > + struct data_buf *buf;
> > +
> > + if (txq->count == 0) {
> > + BT_ERR("invalid parameter: txq->count");
> > + err = -EINVAL;
> > + goto exit_error;
>
> You do all the cleanup inline, so there's really no benefit to "err"
> and the "exit_error" label. You could "return -EINVAL" directly here and similar
> below.
Ack.
>
> > + }
> > +
> > + /* Allocate the same number of buffers as the descriptor */
> > + txq->bufs = kmalloc_array(txq->count, sizeof(*buf), GFP_KERNEL);
> > + if (!txq->bufs) {
> > + err = -ENOMEM;
> > + goto exit_error;
> > + }
> > +
> > + /* Allocate full chunk of data buffer for DMA first and do indexing and
> > + * initialization next, so it can be freed easily
> > + */
> > + txq->buf_v_addr = dma_alloc_coherent(&data->pdev->dev,
> > + txq->count * BUFFER_SIZE,
> > + &txq->buf_p_addr,
> > + GFP_KERNEL | __GFP_NOWARN);
> > + if (!txq->buf_v_addr) {
> > + BT_ERR("Failed to allocate DMA buf");
> > + err = -ENOMEM;
> > + kfree(txq->bufs);
> > + goto exit_error;
> > + }
> > + memset(txq->buf_v_addr, 0, txq->count * BUFFER_SIZE);
> > +
> > + BT_DBG("alloc bufs: p=0x%llx v=0x%p", txq->buf_p_addr,
> > +txq->buf_v_addr);
> > +
> > + /* Setup the allocated DMA buffer to bufs. Each data_buf should
> > + * have virtual address and physical address
> > + */
> > + for (i = 0; i < txq->count; i++) {
> > + buf = &txq->bufs[i];
> > + buf->data_p_addr = txq->buf_p_addr + (i * BUFFER_SIZE);
> > + buf->data = txq->buf_v_addr + (i * BUFFER_SIZE);
> > + }
> > +
> > +exit_error:
> > + return err;
> > +}
>
> > +static int btintel_pcie_setup_rxq_bufs(struct btintel_pcie_data *data,
> > + struct rxq *rxq)
> > +{
> > + int err = 0, i;
> > + struct data_buf *buf;
> > +
> > + if (rxq->count == 0) {
> > + BT_ERR("invalid parameter: rxq->count");
> > + err = -EINVAL;
> > + goto exit_error;
>
> Same "err", "exit_error" comment.
>
Ack.
> > + }
> > +
> > + /* Allocate the same number of buffers as the descriptor */
> > + rxq->bufs = kmalloc_array(rxq->count, sizeof(*buf), GFP_KERNEL);
> > + if (!rxq->bufs) {
> > + err = -ENOMEM;
> > + goto exit_error;
> > + }
> > +
> > + /* Allocate full chunk of data buffer for DMA first and do indexing and
> > + * initialization next, so it can be freed easily
> > + */
> > + rxq->buf_v_addr = dma_alloc_coherent(&data->pdev->dev,
> > + rxq->count * BUFFER_SIZE,
> > + &rxq->buf_p_addr,
> > + GFP_KERNEL | __GFP_NOWARN);
> > + if (!rxq->buf_v_addr) {
> > + BT_ERR("Failed to allocate DMA buf");
> > + err = -ENOMEM;
> > + kfree(rxq->bufs);
> > + goto exit_error;
> > + }
> > + memset(rxq->buf_v_addr, 0, rxq->count * BUFFER_SIZE);
> > +
> > + BT_DBG("alloc bufs: p=0x%llx v=0x%p", rxq->buf_p_addr,
> > +rxq->buf_v_addr);
> > +
> > + /* Setup the allocated DMA buffer to bufs. Each data_buf should
> > + * have virtual address and physical address
> > + */
> > + for (i = 0; i < rxq->count; i++) {
> > + buf = &rxq->bufs[i];
> > + buf->data_p_addr = rxq->buf_p_addr + (i * BUFFER_SIZE);
> > + buf->data = rxq->buf_v_addr + (i * BUFFER_SIZE);
> > + }
> > +
> > +exit_error:
> > +
> > + return err;
> > +}
>
> > +static void btintel_pcie_release_hdev(struct btintel_pcie_data *data)
> > +{
> > + struct hci_dev *hdev;
> > +
> > + hdev = data->hdev;
> > + if (hdev) {
>
> This test shouldn't be necessary if the driver is written correctly.
> We should never get here unless .probe() was successful.
Ack.
>
> > + hci_unregister_dev(hdev);
>
> There should be a corresponding hci_register_dev(). Since that's not here yet,
> I don't think the hci_unregister_dev() should be in this patch either. Looks like
> maybe just incomplete code?
>
> Oh, I see hci_register_dev() is added in patch 3/3. They should be added in
> the same patch.
Ack.
>
> > + hci_free_dev(hdev);
> > + }
> > + data->hdev = NULL;
> > +}
>
> > +static int btintel_pcie_probe(struct pci_dev *pdev,
> > + const struct pci_device_id *ent) {
> > + int err;
> > + struct btintel_pcie_data *data;
> > +
> > + if (!pdev)
> > + return -ENODEV;
> > +
> > + data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL);
> > + if (!data)
> > + return -ENOMEM;
> > +
> > + /* initialize the btintel_pcie data struct */
>
> Superfluous comment.
>
> > + data->pdev = pdev;
> > +
> > + spin_lock_init(&data->irq_lock);
> > + spin_lock_init(&data->hci_rx_lock);
> > +
> > + init_waitqueue_head(&data->gp0_wait_q);
> > + data->gp0_received = false;
> > +
> > + init_waitqueue_head(&data->tx_wait_q);
> > + data->tx_wait_done = false;
> > +
> > + data->workqueue = alloc_ordered_workqueue(KBUILD_MODNAME,
> WQ_HIGHPRI);
> > + if (!data->workqueue) {
> > + BT_ERR("Failed to create workqueue");
> > + return -ENOMEM;
> > + }
> > + skb_queue_head_init(&data->rx_skb_q);
> > + INIT_WORK(&data->rx_work, btintel_pcie_rx_work);
> > +
> > + data->boot_stage_cache = 0x00;
> > + data->img_resp_cache = 0x00;
> > +
> > + /* PCIe specific all to configure it for this device includes
> > + * enabling pice device, setting master, reading BAR[0], configuring
> > + * MSIx, setting DMA mask, and save the driver data.
>
> s/pice/PCIe/
> s/MSIx/MSI-X/
> s/save the/saving the/
>
> Whole comment is probably superfluous since this is common to all PCI
> drivers.
Ack.
>
> > + */
> > + err = btintel_pcie_config_pcie(pdev, data);
> > + if (err) {
> > + BT_ERR("Failed to config pcie (%d)", err);
> > + goto exit_error;
> > + }
> > +
> > + /* Set driver data for this PCI device */
>
> Superfluous comment.
>
> > + pci_set_drvdata(pdev, data);
> > +
> > + /* allocate the IPC struct */
> > + err = btintel_pcie_alloc(data);
> > + if (err) {
> > + BT_ERR("Failed to allocate queues(%d)", err);
> > + goto exit_error;
> > + }
> > +
> > + /* Enable BT function */
>
> Superfluous comment.
>
> > + err = btintel_pcie_enable_bt(data);
> > + if (err) {
> > + BT_ERR("Failed to start bluetooth device(%d)", err);
> > + goto exit_error;
> > + }
> > +
> > + /* CNV information (CNVi and CNVr) is in CSR */
> > + data->cnvi = btintel_pcie_rd_reg32(data, CSR_HW_REV_REG);
> > + BT_DBG("cnvi: 0x%08x", data->cnvi);
> > +
> > + data->cnvr = btintel_pcie_rd_reg32(data, CSR_RF_ID_REG);
> > + BT_DBG("cnvr: 0x%08x", data->cnvr);
> > +
> > + err = btintel_pcie_start_rx(data);
> > + if (err) {
> > + BT_ERR("Failed to start rx (%d)", err);
> > + goto exit_error;
> > + }
> > +
> > + err = btintel_pcie_setup_hdev(data);
> > + if (err) {
> > + BT_ERR("Failed to setup HCI module");
> > + goto exit_error;
> > + }
> > +
> > + return 0;
> > +
> > +exit_error:
> > + /* reset device before leave */
> > + btintel_pcie_reset_bt(data);
> > +
> > + /* clear bus mastering */
>
> Superfluous comment.
>
> > + pci_clear_master(pdev);
> > +
> > + /* Unset driver data for PCI device */
>
> Superfluous comment.
>
> > + pci_set_drvdata(pdev, NULL);
> > +
> > + return err;
> > +}
> > +
> > +static void btintel_pcie_remove(struct pci_dev *pdev) {
> > + struct btintel_pcie_data *data;
> > +
> > + if (!pdev) {
>
> Shouldn't need this check. If you get here with "pdev == NULL", the driver did
> something wrong and it's better to oops so the driver can be fixed.
Ack.
>
> > + BT_ERR("Invalid parameter: pdev");
> > + return;
> > + }
> > +
> > + data = pci_get_drvdata(pdev);
> > + if (!data) {
>
> Or this one.
Ack.
>
> > + BT_ERR("data is empty");
> > + return;
> > + }
> > +
> > + btintel_pcie_release_hdev(data);
> > +
> > + flush_work(&data->rx_work);
> > +
> > + destroy_workqueue(data->workqueue);
> > +
> > + btintel_pcie_free(data);
> > +
> > + /* reset device before leave */
> > + btintel_pcie_reset_bt(data);
> > +
> > + /* clear bus mastering */
>
> Superfluous comment.
>
> > + pci_clear_master(pdev);
> > +
> > + /* Unset driver data for PCI device */
>
> Superfluous comment.
>
> > + pci_set_drvdata(pdev, NULL);
> > +}
> > +
> > +#ifdef CONFIG_PM
> > +static int btintel_pcie_suspend(struct device *dev) {
> > + /* TODO: Add support suspend */
> > + return 0;
> > +}
> > +
> > +static int btintel_pcie_resume(struct device *dev) {
> > + /* TODO: Add support resume */
> > + return 0;
> > +}
> > +
> > +static SIMPLE_DEV_PM_OPS(btintel_pcie_pm_ops, btintel_pcie_suspend,
> > + btintel_pcie_resume);
> > +#endif /* CONFIG_PM */
>
> Seems pointless to include this #ifdef CONFIG_PM code until you implement it.
Ack.
>
> > +static struct pci_driver btintel_pcie_driver = {
> > + .name = KBUILD_MODNAME,
> > + .id_table = btintel_pcie_table,
> > + .probe = btintel_pcie_probe,
> > + .remove = btintel_pcie_remove,
> > +#ifdef CONFIG_PM
> > + .driver.pm = &btintel_pcie_pm_ops,
> > +#endif /* CONFIG_PM */
> > +};
>
> > +/* Default Poll time for MAC access during init*/
> > +#define DEFAULT_MAC_ACCESS_TIMEOUT 200000
>
> Would be nice to have units here in the name (us, ms, etc).
Ack.
>
> > +/* Default interrupt timeout in msec */
> > +#define DEFAULT_INTR_TIMEOUT 3000
>
> And here.
Ack.
>
> > +/* Enum for RBD buffer size mappting */
>
> s/mappting/mapping/ ?
>
> > + * @dbgc_addr: DBGC first fragmemt address
> > + * @dbgc_size: DBGC buffer size
> > + * @early_enable: Enarly debug enable
>
> s/fragmemt/fragment/
> s/Enarly/Early/
Ack.
>
> > + * @dbg_output_mode: Debug output mode
> > + * Bit[4] DBGC O/P { 0=SRAM, 1=DRAM(not relevant for NPK) }
> > + * Bit[5] DBGC I/P { 0=BDBG, 1=DBGI }
> > + * Bits[6:7] DBGI O/P(relevant if bit[5] = 1)
> > + * 0=BT DBGC, 1=WiFi DBGC, 2=NPK }
> > + * @dbg_preset: Debug preset
> > + * @ext_addr: Address of context information extension
> > + * @ext_size: Size of context information part
> > + *
> > + * Total 38 DWords
> > + *
>
> Superfluous blank line
>
> > + */
>
> Bjorn
Thanks,
Kiran
^ permalink raw reply [flat|nested] 16+ messages in thread