[PATCH v3 0/1] Bluetooth: btqca: Add WCN6855 firmware priority selection feature

[PATCH v3 0/1] Bluetooth: btqca: Add WCN6855 firmware priority selection feature

[Shuai Zhang]

Update WCN6855 firmware to use the new FW file and added a fallback mechanism.

changed v2:
- Remove CC satble
- Update commit
- add test steps and log
- Link to v2
  https://lore.kernel.org/all/20251114081751.3940541-2-shuai.zhang@oss.qualcomm.com/

Changes v2:
- Add Fixes tag.
- Add comments in the commit and code to explain the reason for the changes.
- Link to v1
  https://lore.kernel.org/all/20251112074638.1592864-1-quic_shuaz@quicinc.com/

Shuai Zhang (1):
  Bluetooth: btqca: Add WCN6855 firmware priority selection feature

 drivers/bluetooth/btqca.c | 22 ++++++++++++++++++++--
 1 file changed, 20 insertions(+), 2 deletions(-)

-- 
2.34.1

[PATCH v3 1/1] Bluetooth: btqca: Add WCN6855 firmware priority selection feature

[Shuai Zhang]

Historically, WCN685x and QCA2066 shared the same firmware files.
Now, changes are planned for the firmware that will make it incompatible
with QCA2066, so a new firmware name is required for WCN685x.

Test Steps:
 - Boot device
 - Check the BTFW loading status via dmesg

Sanity pass and Test Log:
QCA Downloading qca/wcnhpbftfw21.tlv
Direct firmware load for qca/wcnhpbftfw21.tlv failed with error -2
QCA Downloading qca/hpbftfw21.tlv

Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
---
 drivers/bluetooth/btqca.c | 22 ++++++++++++++++++++--
 1 file changed, 20 insertions(+), 2 deletions(-)

diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c
index 7c958d606..8e0004ef7 100644
--- a/drivers/bluetooth/btqca.c
+++ b/drivers/bluetooth/btqca.c
@@ -847,8 +847,12 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 				 "qca/msbtfw%02x.mbn", rom_ver);
 			break;
 		case QCA_WCN6855:
+			/* Due to historical reasons, WCN685x chip has been using firmware
+			 * without the "wcn" prefix. The mapping between the chip and its
+			 * corresponding firmware has now been corrected.
+			 */
 			snprintf(config.fwname, sizeof(config.fwname),
-				 "qca/hpbtfw%02x.tlv", rom_ver);
+				 "qca/wcnhpbtfw%02x.tlv", rom_ver);
 			break;
 		case QCA_WCN7850:
 			snprintf(config.fwname, sizeof(config.fwname),
@@ -861,6 +865,13 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 	}
 
 	err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
+
+	if (!rampatch_name && err < 0 && soc_type == QCA_WCN6855) {
+		snprintf(config.fwname, sizeof(config.fwname),
+			 "qca/hpbtfw%02x.tlv", rom_ver);
+		err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
+	}
+
 	if (err < 0) {
 		bt_dev_err(hdev, "QCA Failed to download patch (%d)", err);
 		return err;
@@ -923,7 +934,7 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 		case QCA_WCN6855:
 			qca_read_fw_board_id(hdev, &boardid);
 			qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
-						  "hpnv", soc_type, ver, rom_ver, boardid);
+						  "wcnhpnv", soc_type, ver, rom_ver, boardid);
 			break;
 		case QCA_WCN7850:
 			qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
@@ -936,6 +947,13 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 	}
 
 	err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
+
+	if (!firmware_name && err < 0 && soc_type == QCA_WCN6855) {
+		qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
+					  "hpnv", soc_type, ver, rom_ver, boardid);
+		err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
+	}
+
 	if (err < 0) {
 		bt_dev_err(hdev, "QCA Failed to download NVM (%d)", err);
 		return err;
-- 
2.34.1

RE: Bluetooth: btqca: Add WCN6855 firmware priority selection feature

[bluez.test.bot]

[-- Attachment #1: Type: text/plain, Size: 2377 bytes --]

This is automated email and please do not reply to this email!

Dear submitter,

Thank you for submitting the patches to the linux bluetooth mailing list.
This is a CI test results with your patch series:
PW Link:https://patchwork.kernel.org/project/bluetooth/list/?series=1024068

---Test result---

Test Summary:
CheckPatch                    PENDING   0.34 seconds
GitLint                       PENDING   0.26 seconds
SubjectPrefix                 PASS      0.12 seconds
BuildKernel                   PASS      26.38 seconds
CheckAllWarning               PASS      29.85 seconds
CheckSparse                   PASS      33.12 seconds
BuildKernel32                 PASS      26.27 seconds
TestRunnerSetup               PASS      519.32 seconds
TestRunner_l2cap-tester       PASS      25.00 seconds
TestRunner_iso-tester         PASS      74.58 seconds
TestRunner_bnep-tester        PASS      6.51 seconds
TestRunner_mgmt-tester        FAIL      127.02 seconds
TestRunner_rfcomm-tester      PASS      9.65 seconds
TestRunner_sco-tester         PASS      14.92 seconds
TestRunner_ioctl-tester       PASS      10.31 seconds
TestRunner_mesh-tester        FAIL      11.75 seconds
TestRunner_smp-tester         PASS      8.81 seconds
TestRunner_userchan-tester    PASS      6.75 seconds
IncrementalBuild              PENDING   0.57 seconds

Details
##############################
Test: CheckPatch - PENDING
Desc: Run checkpatch.pl script
Output:

##############################
Test: GitLint - PENDING
Desc: Run gitlint
Output:

##############################
Test: TestRunner_mgmt-tester - FAIL
Desc: Run mgmt-tester with test-runner
Output:
Total: 492, Passed: 486 (98.8%), Failed: 2, Not Run: 4

Failed Test Cases
Read Exp Feature - Success                           Failed       0.104 seconds
LL Privacy - Set Flags 3 (2 Devices to RL)           Failed       0.191 seconds
##############################
Test: TestRunner_mesh-tester - FAIL
Desc: Run mesh-tester with test-runner
Output:
Total: 10, Passed: 8 (80.0%), Failed: 2, Not Run: 0

Failed Test Cases
Mesh - Send cancel - 1                               Timed out    1.964 seconds
Mesh - Send cancel - 2                               Timed out    2.000 seconds
##############################
Test: IncrementalBuild - PENDING
Desc: Incremental build with the patches in the series
Output:



---
Regards,
Linux Bluetooth

Re: [PATCH v3 1/1] Bluetooth: btqca: Add WCN6855 firmware priority selection feature

[Shuai Zhang]

Dear

On 11/17/2025 10:16 AM, Shuai Zhang wrote:
> Historically, WCN685x and QCA2066 shared the same firmware files.
> Now, changes are planned for the firmware that will make it incompatible
> with QCA2066, so a new firmware name is required for WCN685x.
>
> Test Steps:
>   - Boot device
>   - Check the BTFW loading status via dmesg
>
> Sanity pass and Test Log:
> QCA Downloading qca/wcnhpbftfw21.tlv
> Direct firmware load for qca/wcnhpbftfw21.tlv failed with error -2
> QCA Downloading qca/hpbftfw21.tlv
>
> Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
> ---
>   drivers/bluetooth/btqca.c | 22 ++++++++++++++++++++--
>   1 file changed, 20 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c
> index 7c958d606..8e0004ef7 100644
> --- a/drivers/bluetooth/btqca.c
> +++ b/drivers/bluetooth/btqca.c
> @@ -847,8 +847,12 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
>   				 "qca/msbtfw%02x.mbn", rom_ver);
>   			break;
>   		case QCA_WCN6855:
> +			/* Due to historical reasons, WCN685x chip has been using firmware
> +			 * without the "wcn" prefix. The mapping between the chip and its
> +			 * corresponding firmware has now been corrected.
> +			 */
>   			snprintf(config.fwname, sizeof(config.fwname),
> -				 "qca/hpbtfw%02x.tlv", rom_ver);
> +				 "qca/wcnhpbtfw%02x.tlv", rom_ver);
>   			break;
>   		case QCA_WCN7850:
>   			snprintf(config.fwname, sizeof(config.fwname),
> @@ -861,6 +865,13 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
>   	}
>   
>   	err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
> +
> +	if (!rampatch_name && err < 0 && soc_type == QCA_WCN6855) {
> +		snprintf(config.fwname, sizeof(config.fwname),
> +			 "qca/hpbtfw%02x.tlv", rom_ver);
> +		err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
> +	}
> +
>   	if (err < 0) {
>   		bt_dev_err(hdev, "QCA Failed to download patch (%d)", err);
>   		return err;
> @@ -923,7 +934,7 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
>   		case QCA_WCN6855:
>   			qca_read_fw_board_id(hdev, &boardid);
>   			qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
> -						  "hpnv", soc_type, ver, rom_ver, boardid);
> +						  "wcnhpnv", soc_type, ver, rom_ver, boardid);
>   			break;
>   		case QCA_WCN7850:
>   			qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
> @@ -936,6 +947,13 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
>   	}
>   
>   	err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
> +
> +	if (!firmware_name && err < 0 && soc_type == QCA_WCN6855) {
> +		qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
> +					  "hpnv", soc_type, ver, rom_ver, boardid);
> +		err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
> +	}
> +
>   	if (err < 0) {
>   		bt_dev_err(hdev, "QCA Failed to download NVM (%d)", err);
>   		return err;

Could you confirm if it has already been accepted?


Kindly,regard

Shuai

Re: [PATCH v3 1/1] Bluetooth: btqca: Add WCN6855 firmware priority selection feature

[Konrad Dybcio]

On 11/18/25 2:44 PM, Shuai Zhang wrote:
> Dear
> 
> On 11/17/2025 10:16 AM, Shuai Zhang wrote:
>> Historically, WCN685x and QCA2066 shared the same firmware files.
>> Now, changes are planned for the firmware that will make it incompatible
>> with QCA2066, so a new firmware name is required for WCN685x.
>>
>> Test Steps:
>>   - Boot device
>>   - Check the BTFW loading status via dmesg
>>
>> Sanity pass and Test Log:
>> QCA Downloading qca/wcnhpbftfw21.tlv
>> Direct firmware load for qca/wcnhpbftfw21.tlv failed with error -2
>> QCA Downloading qca/hpbftfw21.tlv
>>
>> Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
>> ---

[...]

> Could you confirm if it has already been accepted?

Please familiarize yourself with the kernel development cycle. You sent this
patch yesterday, at a very late point in the kernel dev cycle (rc6, normally
rc7 or rc8 is last) when maintainers generally don't accept patches.

https://docs.kernel.org/process/2.Process.html

The branch your changes will land before being queued for torvalds merge
the following cycle is likely:

https://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next.git/log/

which you can watch yourself, although normally maintainers respond with
an "applied, thanks" message

Please also trim your replies, you included a whole patch as context and
only added meaningful text at the very end. Please also don't top-post.
I see you're doing so as a mannerism, but it should generally be avoided.

Konrad

Re: [PATCH v3 1/1] Bluetooth: btqca: Add WCN6855 firmware priority selection feature

[Dmitry Baryshkov]

On Mon, Nov 17, 2025 at 10:16:45AM +0800, Shuai Zhang wrote:
> Historically, WCN685x and QCA2066 shared the same firmware files.
> Now, changes are planned for the firmware that will make it incompatible
> with QCA2066, so a new firmware name is required for WCN685x.
> 
> Test Steps:
>  - Boot device
>  - Check the BTFW loading status via dmesg
> 
> Sanity pass and Test Log:
> QCA Downloading qca/wcnhpbftfw21.tlv
> Direct firmware load for qca/wcnhpbftfw21.tlv failed with error -2
> QCA Downloading qca/hpbftfw21.tlv
> 
> Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
> ---
>  drivers/bluetooth/btqca.c | 22 ++++++++++++++++++++--
>  1 file changed, 20 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c
> index 7c958d606..8e0004ef7 100644
> --- a/drivers/bluetooth/btqca.c
> +++ b/drivers/bluetooth/btqca.c
> @@ -847,8 +847,12 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
>  				 "qca/msbtfw%02x.mbn", rom_ver);
>  			break;
>  		case QCA_WCN6855:
> +			/* Due to historical reasons, WCN685x chip has been using firmware
> +			 * without the "wcn" prefix. The mapping between the chip and its
> +			 * corresponding firmware has now been corrected.
> +			 */
>  			snprintf(config.fwname, sizeof(config.fwname),
> -				 "qca/hpbtfw%02x.tlv", rom_ver);
> +				 "qca/wcnhpbtfw%02x.tlv", rom_ver);
>  			break;
>  		case QCA_WCN7850:
>  			snprintf(config.fwname, sizeof(config.fwname),
> @@ -861,6 +865,13 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
>  	}
>  
>  	err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
> +
> +	if (!rampatch_name && err < 0 && soc_type == QCA_WCN6855) {
> +		snprintf(config.fwname, sizeof(config.fwname),
> +			 "qca/hpbtfw%02x.tlv", rom_ver);
> +		err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
> +	}

Is there a reason for ignoring how it was done already for other cases when
we need a similar fallback? Please extend the existing code (or rewrite
it) instead of adding a similar hook at a completely different place.

> +
>  	if (err < 0) {
>  		bt_dev_err(hdev, "QCA Failed to download patch (%d)", err);
>  		return err;
> @@ -923,7 +934,7 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
>  		case QCA_WCN6855:
>  			qca_read_fw_board_id(hdev, &boardid);
>  			qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
> -						  "hpnv", soc_type, ver, rom_ver, boardid);
> +						  "wcnhpnv", soc_type, ver, rom_ver, boardid);
>  			break;
>  		case QCA_WCN7850:
>  			qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
> @@ -936,6 +947,13 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
>  	}
>  
>  	err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
> +
> +	if (!firmware_name && err < 0 && soc_type == QCA_WCN6855) {
> +		qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
> +					  "hpnv", soc_type, ver, rom_ver, boardid);
> +		err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
> +	}
> +
>  	if (err < 0) {
>  		bt_dev_err(hdev, "QCA Failed to download NVM (%d)", err);
>  		return err;
> -- 
> 2.34.1
> 

-- 
With best wishes
Dmitry

Re: [PATCH v3 1/1] Bluetooth: btqca: Add WCN6855 firmware priority selection feature

[Shuai Zhang]

Hi Dmitry

On 11/19/2025 3:59 PM, Dmitry Baryshkov wrote:
> On Mon, Nov 17, 2025 at 10:16:45AM +0800, Shuai Zhang wrote:
>> Historically, WCN685x and QCA2066 shared the same firmware files.
>> Now, changes are planned for the firmware that will make it incompatible
>> with QCA2066, so a new firmware name is required for WCN685x.
>>
>> Test Steps:
>>   - Boot device
>>   - Check the BTFW loading status via dmesg
>>
>> Sanity pass and Test Log:
>> QCA Downloading qca/wcnhpbftfw21.tlv
>> Direct firmware load for qca/wcnhpbftfw21.tlv failed with error -2
>> QCA Downloading qca/hpbftfw21.tlv
>>
>> Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
>> ---
>>   drivers/bluetooth/btqca.c | 22 ++++++++++++++++++++--
>>   1 file changed, 20 insertions(+), 2 deletions(-)
>>
>> diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c
>> index 7c958d606..8e0004ef7 100644
>> --- a/drivers/bluetooth/btqca.c
>> +++ b/drivers/bluetooth/btqca.c
>> @@ -847,8 +847,12 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
>>   				 "qca/msbtfw%02x.mbn", rom_ver);
>>   			break;
>>   		case QCA_WCN6855:
>> +			/* Due to historical reasons, WCN685x chip has been using firmware
>> +			 * without the "wcn" prefix. The mapping between the chip and its
>> +			 * corresponding firmware has now been corrected.
>> +			 */
>>   			snprintf(config.fwname, sizeof(config.fwname),
>> -				 "qca/hpbtfw%02x.tlv", rom_ver);
>> +				 "qca/wcnhpbtfw%02x.tlv", rom_ver);
>>   			break;
>>   		case QCA_WCN7850:
>>   			snprintf(config.fwname, sizeof(config.fwname),
>> @@ -861,6 +865,13 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
>>   	}
>>   
>>   	err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
>> +
>> +	if (!rampatch_name && err < 0 && soc_type == QCA_WCN6855) {
>> +		snprintf(config.fwname, sizeof(config.fwname),
>> +			 "qca/hpbtfw%02x.tlv", rom_ver);
>> +		err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
>> +	}
> Is there a reason for ignoring how it was done already for other cases when
> we need a similar fallback? Please extend the existing code (or rewrite
> it) instead of adding a similar hook at a completely different place.

Sorry, I missed this email. I will resubmit the new changes using the 
existing callback mechanism.

>> +
>>   	if (err < 0) {
>>   		bt_dev_err(hdev, "QCA Failed to download patch (%d)", err);
>>   		return err;
>> @@ -923,7 +934,7 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
>>   		case QCA_WCN6855:
>>   			qca_read_fw_board_id(hdev, &boardid);
>>   			qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
>> -						  "hpnv", soc_type, ver, rom_ver, boardid);
>> +						  "wcnhpnv", soc_type, ver, rom_ver, boardid);
>>   			break;
>>   		case QCA_WCN7850:
>>   			qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
>> @@ -936,6 +947,13 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
>>   	}
>>   
>>   	err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
>> +
>> +	if (!firmware_name && err < 0 && soc_type == QCA_WCN6855) {
>> +		qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
>> +					  "hpnv", soc_type, ver, rom_ver, boardid);
>> +		err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
>> +	}
>> +
>>   	if (err < 0) {
>>   		bt_dev_err(hdev, "QCA Failed to download NVM (%d)", err);
>>   		return err;
>> -- 
>> 2.34.1

Thanks,

Shuai

Re: [PATCH v3 1/1] Bluetooth: btqca: Add WCN6855 firmware priority selection feature

[Shuai Zhang]

Hi Dmitry

On 11/19/2025 3:59 PM, Dmitry Baryshkov wrote:
> On Mon, Nov 17, 2025 at 10:16:45AM +0800, Shuai Zhang wrote:
>> Historically, WCN685x and QCA2066 shared the same firmware files.
>> Now, changes are planned for the firmware that will make it incompatible
>> with QCA2066, so a new firmware name is required for WCN685x.
>>
>> Test Steps:
>>   - Boot device
>>   - Check the BTFW loading status via dmesg
>>
>> Sanity pass and Test Log:
>> QCA Downloading qca/wcnhpbftfw21.tlv
>> Direct firmware load for qca/wcnhpbftfw21.tlv failed with error -2
>> QCA Downloading qca/hpbftfw21.tlv
>>
>> Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
>> ---
>>   drivers/bluetooth/btqca.c | 22 ++++++++++++++++++++--
>>   1 file changed, 20 insertions(+), 2 deletions(-)
>>
>> diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c
>> index 7c958d606..8e0004ef7 100644
>> --- a/drivers/bluetooth/btqca.c
>> +++ b/drivers/bluetooth/btqca.c
>> @@ -847,8 +847,12 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
>>   				 "qca/msbtfw%02x.mbn", rom_ver);
>>   			break;
>>   		case QCA_WCN6855:
>> +			/* Due to historical reasons, WCN685x chip has been using firmware
>> +			 * without the "wcn" prefix. The mapping between the chip and its
>> +			 * corresponding firmware has now been corrected.
>> +			 */
>>   			snprintf(config.fwname, sizeof(config.fwname),
>> -				 "qca/hpbtfw%02x.tlv", rom_ver);
>> +				 "qca/wcnhpbtfw%02x.tlv", rom_ver);
>>   			break;
>>   		case QCA_WCN7850:
>>   			snprintf(config.fwname, sizeof(config.fwname),
>> @@ -861,6 +865,13 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
>>   	}
>>   
>>   	err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
>> +
>> +	if (!rampatch_name && err < 0 && soc_type == QCA_WCN6855) {
>> +		snprintf(config.fwname, sizeof(config.fwname),
>> +			 "qca/hpbtfw%02x.tlv", rom_ver);
>> +		err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
>> +	}
> Is there a reason for ignoring how it was done already for other cases when
> we need a similar fallback? Please extend the existing code (or rewrite
> it) instead of adding a similar hook at a completely different place.

Current Strategy (when DTS does not specify rampatch and firmware):
     Rampatch: Load the rampatch based on soc_type.
     NVM:  Load the NVM with board_id based on soc_type.
                 If the file corresponding to board_id does not exist, 
then load the NVM file ending with .bin.
     For HSP (new requirement):
         First, load the rampatch/NVM files wcnhpbtfw and wcnhpnv.
         If not found:
         Rampatch: Fall back to loading the hpbtfw rampatch file.
         NVM:  Starting from wcnhpnv.bxxx, load the NVM file ending with 
.bin.
                     If still not found, look for hpnv.bxxx and then 
apply the above NVM strategy again (soc_type(board_id)  to .bin).

The current changes are based on the original implementation, which 
should make them the clearest modifications.
Please review according to the existing strategy, and feel free to let 
me know if you have any questions.
>> +
>>   	if (err < 0) {
>>   		bt_dev_err(hdev, "QCA Failed to download patch (%d)", err);
>>   		return err;
>> @@ -923,7 +934,7 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
>>   		case QCA_WCN6855:
>>   			qca_read_fw_board_id(hdev, &boardid);
>>   			qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
>> -						  "hpnv", soc_type, ver, rom_ver, boardid);
>> +						  "wcnhpnv", soc_type, ver, rom_ver, boardid);
>>   			break;
>>   		case QCA_WCN7850:
>>   			qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
>> @@ -936,6 +947,13 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
>>   	}
>>   
>>   	err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
>> +
>> +	if (!firmware_name && err < 0 && soc_type == QCA_WCN6855) {
>> +		qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
>> +					  "hpnv", soc_type, ver, rom_ver, boardid);
>> +		err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
>> +	}
>> +
>>   	if (err < 0) {
>>   		bt_dev_err(hdev, "QCA Failed to download NVM (%d)", err);
>>   		return err;
>> -- 
>> 2.34.1
>>
Thanks,
Shuai

Re: [PATCH v3 1/1] Bluetooth: btqca: Add WCN6855 firmware priority selection feature

[Dmitry Baryshkov]

On Fri, Dec 19, 2025 at 05:19:30PM +0800, Shuai Zhang wrote:
> Hi Dmitry
> 
> On 11/19/2025 3:59 PM, Dmitry Baryshkov wrote:
> > On Mon, Nov 17, 2025 at 10:16:45AM +0800, Shuai Zhang wrote:
> > > Historically, WCN685x and QCA2066 shared the same firmware files.
> > > Now, changes are planned for the firmware that will make it incompatible
> > > with QCA2066, so a new firmware name is required for WCN685x.
> > > 
> > > Test Steps:
> > >   - Boot device
> > >   - Check the BTFW loading status via dmesg
> > > 
> > > Sanity pass and Test Log:
> > > QCA Downloading qca/wcnhpbftfw21.tlv
> > > Direct firmware load for qca/wcnhpbftfw21.tlv failed with error -2
> > > QCA Downloading qca/hpbftfw21.tlv
> > > 
> > > Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
> > > ---
> > >   drivers/bluetooth/btqca.c | 22 ++++++++++++++++++++--
> > >   1 file changed, 20 insertions(+), 2 deletions(-)
> > > 
> > > diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c
> > > index 7c958d606..8e0004ef7 100644
> > > --- a/drivers/bluetooth/btqca.c
> > > +++ b/drivers/bluetooth/btqca.c
> > > @@ -847,8 +847,12 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
> > >   				 "qca/msbtfw%02x.mbn", rom_ver);
> > >   			break;
> > >   		case QCA_WCN6855:
> > > +			/* Due to historical reasons, WCN685x chip has been using firmware
> > > +			 * without the "wcn" prefix. The mapping between the chip and its
> > > +			 * corresponding firmware has now been corrected.
> > > +			 */
> > >   			snprintf(config.fwname, sizeof(config.fwname),
> > > -				 "qca/hpbtfw%02x.tlv", rom_ver);
> > > +				 "qca/wcnhpbtfw%02x.tlv", rom_ver);
> > >   			break;
> > >   		case QCA_WCN7850:
> > >   			snprintf(config.fwname, sizeof(config.fwname),
> > > @@ -861,6 +865,13 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
> > >   	}
> > >   	err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
> > > +
> > > +	if (!rampatch_name && err < 0 && soc_type == QCA_WCN6855) {
> > > +		snprintf(config.fwname, sizeof(config.fwname),
> > > +			 "qca/hpbtfw%02x.tlv", rom_ver);
> > > +		err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
> > > +	}
> > Is there a reason for ignoring how it was done already for other cases when
> > we need a similar fallback? Please extend the existing code (or rewrite
> > it) instead of adding a similar hook at a completely different place.
> 
> Current Strategy (when DTS does not specify rampatch and firmware):
>     Rampatch: Load the rampatch based on soc_type.
>     NVM:  Load the NVM with board_id based on soc_type.
>                 If the file corresponding to board_id does not exist, then
> load the NVM file ending with .bin.
>     For HSP (new requirement):
>         First, load the rampatch/NVM files wcnhpbtfw and wcnhpnv.
>         If not found:
>         Rampatch: Fall back to loading the hpbtfw rampatch file.
>         NVM:  Starting from wcnhpnv.bxxx, load the NVM file ending with
> .bin.
>                     If still not found, look for hpnv.bxxx and then apply
> the above NVM strategy again (soc_type(board_id)  to .bin).
> 
> The current changes are based on the original implementation, which should
> make them the clearest modifications.
> Please review according to the existing strategy, and feel free to let me
> know if you have any questions.

qca_download_firmware() has workaround code for WCN6750, loading TLV
file if MBN is not present. It doesn't make sense to have similar
workardounds in two different places. Could you please unify code
(either by moving existing code or by moving your workaround).

> > > +
> > >   	if (err < 0) {
> > >   		bt_dev_err(hdev, "QCA Failed to download patch (%d)", err);
> > >   		return err;
> > > @@ -923,7 +934,7 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
> > >   		case QCA_WCN6855:
> > >   			qca_read_fw_board_id(hdev, &boardid);
> > >   			qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
> > > -						  "hpnv", soc_type, ver, rom_ver, boardid);
> > > +						  "wcnhpnv", soc_type, ver, rom_ver, boardid);
> > >   			break;
> > >   		case QCA_WCN7850:
> > >   			qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
> > > @@ -936,6 +947,13 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
> > >   	}
> > >   	err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
> > > +
> > > +	if (!firmware_name && err < 0 && soc_type == QCA_WCN6855) {
> > > +		qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
> > > +					  "hpnv", soc_type, ver, rom_ver, boardid);
> > > +		err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
> > > +	}
> > > +
> > >   	if (err < 0) {
> > >   		bt_dev_err(hdev, "QCA Failed to download NVM (%d)", err);
> > >   		return err;
> > > -- 
> > > 2.34.1
> > > 
> Thanks,
> Shuai

-- 
With best wishes
Dmitry

Re: [PATCH v3 1/1] Bluetooth: btqca: Add WCN6855 firmware priority selection feature

[Shuai Zhang]

Hi Dmitry

On 12/21/2025 11:21 PM, Dmitry Baryshkov wrote:
> On Fri, Dec 19, 2025 at 05:19:30PM +0800, Shuai Zhang wrote:
>> Hi Dmitry
>>
>> On 11/19/2025 3:59 PM, Dmitry Baryshkov wrote:
>>> On Mon, Nov 17, 2025 at 10:16:45AM +0800, Shuai Zhang wrote:
>>>> Historically, WCN685x and QCA2066 shared the same firmware files.
>>>> Now, changes are planned for the firmware that will make it incompatible
>>>> with QCA2066, so a new firmware name is required for WCN685x.
>>>>
>>>> Test Steps:
>>>>    - Boot device
>>>>    - Check the BTFW loading status via dmesg
>>>>
>>>> Sanity pass and Test Log:
>>>> QCA Downloading qca/wcnhpbftfw21.tlv
>>>> Direct firmware load for qca/wcnhpbftfw21.tlv failed with error -2
>>>> QCA Downloading qca/hpbftfw21.tlv
>>>>
>>>> Signed-off-by: Shuai Zhang<shuai.zhang@oss.qualcomm.com>
>>>> ---
>>>>    drivers/bluetooth/btqca.c | 22 ++++++++++++++++++++--
>>>>    1 file changed, 20 insertions(+), 2 deletions(-)
>>>>
>>>> diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c
>>>> index 7c958d606..8e0004ef7 100644
>>>> --- a/drivers/bluetooth/btqca.c
>>>> +++ b/drivers/bluetooth/btqca.c
>>>> @@ -847,8 +847,12 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
>>>>    				 "qca/msbtfw%02x.mbn", rom_ver);
>>>>    			break;
>>>>    		case QCA_WCN6855:
>>>> +			/* Due to historical reasons, WCN685x chip has been using firmware
>>>> +			 * without the "wcn" prefix. The mapping between the chip and its
>>>> +			 * corresponding firmware has now been corrected.
>>>> +			 */
>>>>    			snprintf(config.fwname, sizeof(config.fwname),
>>>> -				 "qca/hpbtfw%02x.tlv", rom_ver);
>>>> +				 "qca/wcnhpbtfw%02x.tlv", rom_ver);
>>>>    			break;
>>>>    		case QCA_WCN7850:
>>>>    			snprintf(config.fwname, sizeof(config.fwname),
>>>> @@ -861,6 +865,13 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
>>>>    	}
>>>>    	err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
>>>> +
>>>> +	if (!rampatch_name && err < 0 && soc_type == QCA_WCN6855) {
>>>> +		snprintf(config.fwname, sizeof(config.fwname),
>>>> +			 "qca/hpbtfw%02x.tlv", rom_ver);
>>>> +		err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
>>>> +	}
>>> Is there a reason for ignoring how it was done already for other cases when
>>> we need a similar fallback? Please extend the existing code (or rewrite
>>> it) instead of adding a similar hook at a completely different place.
>> Current Strategy (when DTS does not specify rampatch and firmware):
>>      Rampatch: Load the rampatch based on soc_type.
>>      NVM:  Load the NVM with board_id based on soc_type.
>>                  If the file corresponding to board_id does not exist, then
>> load the NVM file ending with .bin.
>>      For HSP (new requirement):
>>          First, load the rampatch/NVM files wcnhpbtfw and wcnhpnv.
>>          If not found:
>>          Rampatch: Fall back to loading the hpbtfw rampatch file.
>>          NVM:  Starting from wcnhpnv.bxxx, load the NVM file ending with
>> .bin.
>>                      If still not found, look for hpnv.bxxx and then apply
>> the above NVM strategy again (soc_type(board_id)  to .bin).
>>
>> The current changes are based on the original implementation, which should
>> make them the clearest modifications.
>> Please review according to the existing strategy, and feel free to let me
>> know if you have any questions.
> qca_download_firmware() has workaround code for WCN6750, loading TLV
> file if MBN is not present. It doesn't make sense to have similar
> workardounds in two different places. Could you please unify code
> (either by moving existing code or by moving your workaround).
I tried to move the changes into |qca_download_firmware|, but it 
conflicts with the logic for
loading the default NVM. Specifically, when there is no NVM 
corresponding to the board_id,
it will not load the |.bin| NVM file. I’m not sure whether this 
limitation is within a controllable range.

https://github.com/shuaz-shuai/Add-WCN6855-firmware-priority-selection-feature

>>>> +
>>>>    	if (err < 0) {
>>>>    		bt_dev_err(hdev, "QCA Failed to download patch (%d)", err);
>>>>    		return err;
>>>> @@ -923,7 +934,7 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
>>>>    		case QCA_WCN6855:
>>>>    			qca_read_fw_board_id(hdev, &boardid);
>>>>    			qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
>>>> -						  "hpnv", soc_type, ver, rom_ver, boardid);
>>>> +						  "wcnhpnv", soc_type, ver, rom_ver, boardid);
>>>>    			break;
>>>>    		case QCA_WCN7850:
>>>>    			qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
>>>> @@ -936,6 +947,13 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
>>>>    	}
>>>>    	err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
>>>> +
>>>> +	if (!firmware_name && err < 0 && soc_type == QCA_WCN6855) {
>>>> +		qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
>>>> +					  "hpnv", soc_type, ver, rom_ver, boardid);
>>>> +		err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
>>>> +	}
>>>> +
>>>>    	if (err < 0) {
>>>>    		bt_dev_err(hdev, "QCA Failed to download NVM (%d)", err);
>>>>    		return err;
>>>> -- 
>>>> 2.34.1
>>>>
>> Thanks,
>> Shuai

Re: [PATCH v3 1/1] Bluetooth: btqca: Add WCN6855 firmware priority selection feature

[Dmitry Baryshkov]

On Tue, Dec 23, 2025 at 10:03:44AM +0800, Shuai Zhang wrote:
> Hi Dmitry
> 
> On 12/21/2025 11:21 PM, Dmitry Baryshkov wrote:
> > On Fri, Dec 19, 2025 at 05:19:30PM +0800, Shuai Zhang wrote:
> > > Hi Dmitry
> > > 
> > > On 11/19/2025 3:59 PM, Dmitry Baryshkov wrote:
> > > > On Mon, Nov 17, 2025 at 10:16:45AM +0800, Shuai Zhang wrote:
> > > > > Historically, WCN685x and QCA2066 shared the same firmware files.
> > > > > Now, changes are planned for the firmware that will make it incompatible
> > > > > with QCA2066, so a new firmware name is required for WCN685x.
> > > > > 
> > > > > Test Steps:
> > > > >    - Boot device
> > > > >    - Check the BTFW loading status via dmesg
> > > > > 
> > > > > Sanity pass and Test Log:
> > > > > QCA Downloading qca/wcnhpbftfw21.tlv
> > > > > Direct firmware load for qca/wcnhpbftfw21.tlv failed with error -2
> > > > > QCA Downloading qca/hpbftfw21.tlv
> > > > > 
> > > > > Signed-off-by: Shuai Zhang<shuai.zhang@oss.qualcomm.com>
> > > > > ---
> > > > >    drivers/bluetooth/btqca.c | 22 ++++++++++++++++++++--
> > > > >    1 file changed, 20 insertions(+), 2 deletions(-)
> > > > > 
> > > > > diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c
> > > > > index 7c958d606..8e0004ef7 100644
> > > > > --- a/drivers/bluetooth/btqca.c
> > > > > +++ b/drivers/bluetooth/btqca.c
> > > > > @@ -847,8 +847,12 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
> > > > >    				 "qca/msbtfw%02x.mbn", rom_ver);
> > > > >    			break;
> > > > >    		case QCA_WCN6855:
> > > > > +			/* Due to historical reasons, WCN685x chip has been using firmware
> > > > > +			 * without the "wcn" prefix. The mapping between the chip and its
> > > > > +			 * corresponding firmware has now been corrected.
> > > > > +			 */
> > > > >    			snprintf(config.fwname, sizeof(config.fwname),
> > > > > -				 "qca/hpbtfw%02x.tlv", rom_ver);
> > > > > +				 "qca/wcnhpbtfw%02x.tlv", rom_ver);
> > > > >    			break;
> > > > >    		case QCA_WCN7850:
> > > > >    			snprintf(config.fwname, sizeof(config.fwname),
> > > > > @@ -861,6 +865,13 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
> > > > >    	}
> > > > >    	err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
> > > > > +
> > > > > +	if (!rampatch_name && err < 0 && soc_type == QCA_WCN6855) {
> > > > > +		snprintf(config.fwname, sizeof(config.fwname),
> > > > > +			 "qca/hpbtfw%02x.tlv", rom_ver);
> > > > > +		err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
> > > > > +	}
> > > > Is there a reason for ignoring how it was done already for other cases when
> > > > we need a similar fallback? Please extend the existing code (or rewrite
> > > > it) instead of adding a similar hook at a completely different place.
> > > Current Strategy (when DTS does not specify rampatch and firmware):
> > >      Rampatch: Load the rampatch based on soc_type.
> > >      NVM:  Load the NVM with board_id based on soc_type.
> > >                  If the file corresponding to board_id does not exist, then
> > > load the NVM file ending with .bin.
> > >      For HSP (new requirement):
> > >          First, load the rampatch/NVM files wcnhpbtfw and wcnhpnv.
> > >          If not found:
> > >          Rampatch: Fall back to loading the hpbtfw rampatch file.
> > >          NVM:  Starting from wcnhpnv.bxxx, load the NVM file ending with
> > > .bin.
> > >                      If still not found, look for hpnv.bxxx and then apply
> > > the above NVM strategy again (soc_type(board_id)  to .bin).
> > > 
> > > The current changes are based on the original implementation, which should
> > > make them the clearest modifications.
> > > Please review according to the existing strategy, and feel free to let me
> > > know if you have any questions.
> > qca_download_firmware() has workaround code for WCN6750, loading TLV
> > file if MBN is not present. It doesn't make sense to have similar
> > workardounds in two different places. Could you please unify code
> > (either by moving existing code or by moving your workaround).
> I tried to move the changes into |qca_download_firmware|, but it conflicts
> with the logic for
> loading the default NVM. Specifically, when there is no NVM corresponding to
> the board_id,
> it will not load the |.bin| NVM file. I’m not sure whether this limitation
> is within a controllable range.
> 
> https://github.com/shuaz-shuai/Add-WCN6855-firmware-priority-selection-feature

So, the solution is to move the quirk for WCN6750 out of
qca_download_firmware().

> 
> > > > > +
> > > > >    	if (err < 0) {
> > > > >    		bt_dev_err(hdev, "QCA Failed to download patch (%d)", err);
> > > > >    		return err;
> > > > > @@ -923,7 +934,7 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
> > > > >    		case QCA_WCN6855:
> > > > >    			qca_read_fw_board_id(hdev, &boardid);
> > > > >    			qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
> > > > > -						  "hpnv", soc_type, ver, rom_ver, boardid);
> > > > > +						  "wcnhpnv", soc_type, ver, rom_ver, boardid);
> > > > >    			break;
> > > > >    		case QCA_WCN7850:
> > > > >    			qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
> > > > > @@ -936,6 +947,13 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
> > > > >    	}
> > > > >    	err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
> > > > > +
> > > > > +	if (!firmware_name && err < 0 && soc_type == QCA_WCN6855) {
> > > > > +		qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
> > > > > +					  "hpnv", soc_type, ver, rom_ver, boardid);
> > > > > +		err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
> > > > > +	}
> > > > > +
> > > > >    	if (err < 0) {
> > > > >    		bt_dev_err(hdev, "QCA Failed to download NVM (%d)", err);
> > > > >    		return err;
> > > > > -- 
> > > > > 2.34.1
> > > > > 
> > > Thanks,
> > > Shuai

-- 
With best wishes
Dmitry

Re: [PATCH v3 1/1] Bluetooth: btqca: Add WCN6855 firmware priority selection feature

[Shuai Zhang]

On 12/24/2025 12:23 PM, Dmitry Baryshkov wrote:
> On Tue, Dec 23, 2025 at 10:03:44AM +0800, Shuai Zhang wrote:
>> Hi Dmitry
>>
>> On 12/21/2025 11:21 PM, Dmitry Baryshkov wrote:
>>> On Fri, Dec 19, 2025 at 05:19:30PM +0800, Shuai Zhang wrote:
>>>> Hi Dmitry
>>>>
>>>> On 11/19/2025 3:59 PM, Dmitry Baryshkov wrote:
>>>>> On Mon, Nov 17, 2025 at 10:16:45AM +0800, Shuai Zhang wrote:
>>>>>> Historically, WCN685x and QCA2066 shared the same firmware files.
>>>>>> Now, changes are planned for the firmware that will make it incompatible
>>>>>> with QCA2066, so a new firmware name is required for WCN685x.
>>>>>>
>>>>>> Test Steps:
>>>>>>     - Boot device
>>>>>>     - Check the BTFW loading status via dmesg
>>>>>>
>>>>>> Sanity pass and Test Log:
>>>>>> QCA Downloading qca/wcnhpbftfw21.tlv
>>>>>> Direct firmware load for qca/wcnhpbftfw21.tlv failed with error -2
>>>>>> QCA Downloading qca/hpbftfw21.tlv
>>>>>>
>>>>>> Signed-off-by: Shuai Zhang<shuai.zhang@oss.qualcomm.com>
>>>>>> ---
>>>>>>     drivers/bluetooth/btqca.c | 22 ++++++++++++++++++++--
>>>>>>     1 file changed, 20 insertions(+), 2 deletions(-)
>>>>>>
>>>>>> diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c
>>>>>> index 7c958d606..8e0004ef7 100644
>>>>>> --- a/drivers/bluetooth/btqca.c
>>>>>> +++ b/drivers/bluetooth/btqca.c
>>>>>> @@ -847,8 +847,12 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
>>>>>>     				 "qca/msbtfw%02x.mbn", rom_ver);
>>>>>>     			break;
>>>>>>     		case QCA_WCN6855:
>>>>>> +			/* Due to historical reasons, WCN685x chip has been using firmware
>>>>>> +			 * without the "wcn" prefix. The mapping between the chip and its
>>>>>> +			 * corresponding firmware has now been corrected.
>>>>>> +			 */
>>>>>>     			snprintf(config.fwname, sizeof(config.fwname),
>>>>>> -				 "qca/hpbtfw%02x.tlv", rom_ver);
>>>>>> +				 "qca/wcnhpbtfw%02x.tlv", rom_ver);
>>>>>>     			break;
>>>>>>     		case QCA_WCN7850:
>>>>>>     			snprintf(config.fwname, sizeof(config.fwname),
>>>>>> @@ -861,6 +865,13 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
>>>>>>     	}
>>>>>>     	err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
>>>>>> +
>>>>>> +	if (!rampatch_name && err < 0 && soc_type == QCA_WCN6855) {
>>>>>> +		snprintf(config.fwname, sizeof(config.fwname),
>>>>>> +			 "qca/hpbtfw%02x.tlv", rom_ver);
>>>>>> +		err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
>>>>>> +	}
>>>>> Is there a reason for ignoring how it was done already for other cases when
>>>>> we need a similar fallback? Please extend the existing code (or rewrite
>>>>> it) instead of adding a similar hook at a completely different place.
>>>> Current Strategy (when DTS does not specify rampatch and firmware):
>>>>       Rampatch: Load the rampatch based on soc_type.
>>>>       NVM:  Load the NVM with board_id based on soc_type.
>>>>                   If the file corresponding to board_id does not exist, then
>>>> load the NVM file ending with .bin.
>>>>       For HSP (new requirement):
>>>>           First, load the rampatch/NVM files wcnhpbtfw and wcnhpnv.
>>>>           If not found:
>>>>           Rampatch: Fall back to loading the hpbtfw rampatch file.
>>>>           NVM:  Starting from wcnhpnv.bxxx, load the NVM file ending with
>>>> .bin.
>>>>                       If still not found, look for hpnv.bxxx and then apply
>>>> the above NVM strategy again (soc_type(board_id)  to .bin).
>>>>
>>>> The current changes are based on the original implementation, which should
>>>> make them the clearest modifications.
>>>> Please review according to the existing strategy, and feel free to let me
>>>> know if you have any questions.
>>> qca_download_firmware() has workaround code for WCN6750, loading TLV
>>> file if MBN is not present. It doesn't make sense to have similar
>>> workardounds in two different places. Could you please unify code
>>> (either by moving existing code or by moving your workaround).
>> I tried to move the changes into |qca_download_firmware|, but it conflicts
>> with the logic for
>> loading the default NVM. Specifically, when there is no NVM corresponding to
>> the board_id,
>> it will not load the |.bin| NVM file. I’m not sure whether this limitation
>> is within a controllable range.
>>
>> https://github.com/shuaz-shuai/Add-WCN6855-firmware-priority-selection-feature
> So, the solution is to move the quirk for WCN6750 out of
> qca_download_firmware().

I’m not entirely clear on the rationale for removing WCN6750,

as our current discussion focuses on handling WCN6855.


If the logic for loading hpbtfw.tlv and hpnv.bxxx when wcnhpbtfw.tlv and 
wcnhpnv.bxxx

are missing is moved into qca_download_firmware(),

it won’t affect the firmware (hpbtfw.tlv). However, for NVM, if loading 
hpnv.bxxx fails,

the hpnv.bin file will also not be loaded, which is a defect.

This is why I prefer retaining the V3 changes.

Please let me know if you have any concerns or questions.

>>>>>> +
>>>>>>     	if (err < 0) {
>>>>>>     		bt_dev_err(hdev, "QCA Failed to download patch (%d)", err);
>>>>>>     		return err;
>>>>>> @@ -923,7 +934,7 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
>>>>>>     		case QCA_WCN6855:
>>>>>>     			qca_read_fw_board_id(hdev, &boardid);
>>>>>>     			qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
>>>>>> -						  "hpnv", soc_type, ver, rom_ver, boardid);
>>>>>> +						  "wcnhpnv", soc_type, ver, rom_ver, boardid);
>>>>>>     			break;
>>>>>>     		case QCA_WCN7850:
>>>>>>     			qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
>>>>>> @@ -936,6 +947,13 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
>>>>>>     	}
>>>>>>     	err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
>>>>>> +
>>>>>> +	if (!firmware_name && err < 0 && soc_type == QCA_WCN6855) {
>>>>>> +		qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
>>>>>> +					  "hpnv", soc_type, ver, rom_ver, boardid);
>>>>>> +		err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
>>>>>> +	}
>>>>>> +
>>>>>>     	if (err < 0) {
>>>>>>     		bt_dev_err(hdev, "QCA Failed to download NVM (%d)", err);
>>>>>>     		return err;
>>>>>> -- 
>>>>>> 2.34.1
>>>>>>
>>>> Thanks,
>>>> Shuai

Re: [PATCH v3 1/1] Bluetooth: btqca: Add WCN6855 firmware priority selection feature

[Dmitry Baryshkov]

On Wed, Dec 24, 2025 at 02:54:24PM +0800, Shuai Zhang wrote:
> 
> On 12/24/2025 12:23 PM, Dmitry Baryshkov wrote:
> > On Tue, Dec 23, 2025 at 10:03:44AM +0800, Shuai Zhang wrote:
> > > Hi Dmitry
> > > 
> > > On 12/21/2025 11:21 PM, Dmitry Baryshkov wrote:
> > > > On Fri, Dec 19, 2025 at 05:19:30PM +0800, Shuai Zhang wrote:
> > > > > Hi Dmitry
> > > > > 
> > > > > On 11/19/2025 3:59 PM, Dmitry Baryshkov wrote:
> > > > > > On Mon, Nov 17, 2025 at 10:16:45AM +0800, Shuai Zhang wrote:
> > > > > > > Historically, WCN685x and QCA2066 shared the same firmware files.
> > > > > > > Now, changes are planned for the firmware that will make it incompatible
> > > > > > > with QCA2066, so a new firmware name is required for WCN685x.
> > > > > > > 
> > > > > > > Test Steps:
> > > > > > >     - Boot device
> > > > > > >     - Check the BTFW loading status via dmesg
> > > > > > > 
> > > > > > > Sanity pass and Test Log:
> > > > > > > QCA Downloading qca/wcnhpbftfw21.tlv
> > > > > > > Direct firmware load for qca/wcnhpbftfw21.tlv failed with error -2
> > > > > > > QCA Downloading qca/hpbftfw21.tlv
> > > > > > > 
> > > > > > > Signed-off-by: Shuai Zhang<shuai.zhang@oss.qualcomm.com>
> > > > > > > ---
> > > > > > >     drivers/bluetooth/btqca.c | 22 ++++++++++++++++++++--
> > > > > > >     1 file changed, 20 insertions(+), 2 deletions(-)
> > > > > > > 
> > > > > > > diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c
> > > > > > > index 7c958d606..8e0004ef7 100644
> > > > > > > --- a/drivers/bluetooth/btqca.c
> > > > > > > +++ b/drivers/bluetooth/btqca.c
> > > > > > > @@ -847,8 +847,12 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
> > > > > > >     				 "qca/msbtfw%02x.mbn", rom_ver);
> > > > > > >     			break;
> > > > > > >     		case QCA_WCN6855:
> > > > > > > +			/* Due to historical reasons, WCN685x chip has been using firmware
> > > > > > > +			 * without the "wcn" prefix. The mapping between the chip and its
> > > > > > > +			 * corresponding firmware has now been corrected.
> > > > > > > +			 */
> > > > > > >     			snprintf(config.fwname, sizeof(config.fwname),
> > > > > > > -				 "qca/hpbtfw%02x.tlv", rom_ver);
> > > > > > > +				 "qca/wcnhpbtfw%02x.tlv", rom_ver);
> > > > > > >     			break;
> > > > > > >     		case QCA_WCN7850:
> > > > > > >     			snprintf(config.fwname, sizeof(config.fwname),
> > > > > > > @@ -861,6 +865,13 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
> > > > > > >     	}
> > > > > > >     	err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
> > > > > > > +
> > > > > > > +	if (!rampatch_name && err < 0 && soc_type == QCA_WCN6855) {
> > > > > > > +		snprintf(config.fwname, sizeof(config.fwname),
> > > > > > > +			 "qca/hpbtfw%02x.tlv", rom_ver);
> > > > > > > +		err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
> > > > > > > +	}
> > > > > > Is there a reason for ignoring how it was done already for other cases when
> > > > > > we need a similar fallback? Please extend the existing code (or rewrite
> > > > > > it) instead of adding a similar hook at a completely different place.
> > > > > Current Strategy (when DTS does not specify rampatch and firmware):
> > > > >       Rampatch: Load the rampatch based on soc_type.
> > > > >       NVM:  Load the NVM with board_id based on soc_type.
> > > > >                   If the file corresponding to board_id does not exist, then
> > > > > load the NVM file ending with .bin.
> > > > >       For HSP (new requirement):
> > > > >           First, load the rampatch/NVM files wcnhpbtfw and wcnhpnv.
> > > > >           If not found:
> > > > >           Rampatch: Fall back to loading the hpbtfw rampatch file.
> > > > >           NVM:  Starting from wcnhpnv.bxxx, load the NVM file ending with
> > > > > .bin.
> > > > >                       If still not found, look for hpnv.bxxx and then apply
> > > > > the above NVM strategy again (soc_type(board_id)  to .bin).
> > > > > 
> > > > > The current changes are based on the original implementation, which should
> > > > > make them the clearest modifications.
> > > > > Please review according to the existing strategy, and feel free to let me
> > > > > know if you have any questions.
> > > > qca_download_firmware() has workaround code for WCN6750, loading TLV
> > > > file if MBN is not present. It doesn't make sense to have similar
> > > > workardounds in two different places. Could you please unify code
> > > > (either by moving existing code or by moving your workaround).
> > > I tried to move the changes into |qca_download_firmware|, but it conflicts
> > > with the logic for
> > > loading the default NVM. Specifically, when there is no NVM corresponding to
> > > the board_id,
> > > it will not load the |.bin| NVM file. I’m not sure whether this limitation
> > > is within a controllable range.
> > > 
> > > https://github.com/shuaz-shuai/Add-WCN6855-firmware-priority-selection-feature
> > So, the solution is to move the quirk for WCN6750 out of
> > qca_download_firmware().
> 
> I’m not entirely clear on the rationale for removing WCN6750,
> 
> as our current discussion focuses on handling WCN6855.
> 

As I wrote earlier, code uniformity. We already have a quirk code
handling almost the same pattern as yours: load the fallback file if the
expected one is missing.

Also please fix your editor not to insert extra empty lines in your response.

> 
> If the logic for loading hpbtfw.tlv and hpnv.bxxx when wcnhpbtfw.tlv and
> wcnhpnv.bxxx
> 
> are missing is moved into qca_download_firmware(),
> 
> it won’t affect the firmware (hpbtfw.tlv). However, for NVM, if loading
> hpnv.bxxx fails,
> 
> the hpnv.bin file will also not be loaded, which is a defect.

As I wrote, you are providing more and more arguments for moving WCN6750
code from qca_download_firmware() to the caller site.

> 
> This is why I prefer retaining the V3 changes.
> 
> Please let me know if you have any concerns or questions.
> 
> > > > > > > +
> > > > > > >     	if (err < 0) {
> > > > > > >     		bt_dev_err(hdev, "QCA Failed to download patch (%d)", err);
> > > > > > >     		return err;
> > > > > > > @@ -923,7 +934,7 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
> > > > > > >     		case QCA_WCN6855:
> > > > > > >     			qca_read_fw_board_id(hdev, &boardid);
> > > > > > >     			qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
> > > > > > > -						  "hpnv", soc_type, ver, rom_ver, boardid);
> > > > > > > +						  "wcnhpnv", soc_type, ver, rom_ver, boardid);
> > > > > > >     			break;
> > > > > > >     		case QCA_WCN7850:
> > > > > > >     			qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
> > > > > > > @@ -936,6 +947,13 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
> > > > > > >     	}
> > > > > > >     	err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
> > > > > > > +
> > > > > > > +	if (!firmware_name && err < 0 && soc_type == QCA_WCN6855) {
> > > > > > > +		qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
> > > > > > > +					  "hpnv", soc_type, ver, rom_ver, boardid);
> > > > > > > +		err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
> > > > > > > +	}
> > > > > > > +
> > > > > > >     	if (err < 0) {
> > > > > > >     		bt_dev_err(hdev, "QCA Failed to download NVM (%d)", err);
> > > > > > >     		return err;
> > > > > > > -- 
> > > > > > > 2.34.1
> > > > > > > 
> > > > > Thanks,
> > > > > Shuai

-- 
With best wishes
Dmitry

[PATCH v4 1/1] Bluetooth: btqca: Add WCN6855 firmware priority selection feature

[Shuai Zhang]

Historically, WCN685x and QCA2066 shared the same firmware files.
Now, changes are planned for the firmware that will make it incompatible
with QCA2066, so a new firmware name is required for WCN685x.

To code uniformity, move WCN7850 workaround to the caller.

Test Steps:
 - Boot device
 - Check the BTFW loading status via dmesg

Sanity pass and Test Log:
QCA Downloading qca/wcnhpbftfw21.tlv
Direct firmware load for qca/wcnhpbftfw21.tlv failed with error -2
QCA Downloading qca/hpbftfw21.tlv

Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
---
 drivers/bluetooth/btqca.c | 62 +++++++++++++++++++++++----------------
 1 file changed, 37 insertions(+), 25 deletions(-)

diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c
index 7c958d606..81b0208cf 100644
--- a/drivers/bluetooth/btqca.c
+++ b/drivers/bluetooth/btqca.c
@@ -581,28 +581,11 @@ static int qca_download_firmware(struct hci_dev *hdev,
 
 	ret = request_firmware(&fw, config->fwname, &hdev->dev);
 	if (ret) {
-		/* For WCN6750, if mbn file is not present then check for
-		 * tlv file.
-		 */
-		if (soc_type == QCA_WCN6750 && config->type == ELF_TYPE_PATCH) {
-			bt_dev_dbg(hdev, "QCA Failed to request file: %s (%d)",
-				   config->fwname, ret);
-			config->type = TLV_TYPE_PATCH;
-			snprintf(config->fwname, sizeof(config->fwname),
-				 "qca/msbtfw%02x.tlv", rom_ver);
-			bt_dev_info(hdev, "QCA Downloading %s", config->fwname);
-			ret = request_firmware(&fw, config->fwname, &hdev->dev);
-			if (ret) {
-				bt_dev_err(hdev, "QCA Failed to request file: %s (%d)",
-					   config->fwname, ret);
-				return ret;
-			}
-		}
 		/* If the board-specific file is missing, try loading the default
 		 * one, unless that was attempted already.
 		 */
-		else if (config->type == TLV_TYPE_NVM &&
-			 qca_get_alt_nvm_file(config->fwname, sizeof(config->fwname))) {
+		if (config->type == TLV_TYPE_NVM &&
+		    qca_get_alt_nvm_file(config->fwname, sizeof(config->fwname))) {
 			bt_dev_info(hdev, "QCA Downloading %s", config->fwname);
 			ret = request_firmware(&fw, config->fwname, &hdev->dev);
 			if (ret) {
@@ -847,8 +830,12 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 				 "qca/msbtfw%02x.mbn", rom_ver);
 			break;
 		case QCA_WCN6855:
+			/* Due to historical reasons, WCN685x chip has been using firmware
+			 * without the "wcn" prefix. The mapping between the chip and its
+			 * corresponding firmware has now been corrected.
+			 */
 			snprintf(config.fwname, sizeof(config.fwname),
-				 "qca/hpbtfw%02x.tlv", rom_ver);
+				 "qca/wcnhpbtfw%02x.tlv", rom_ver);
 			break;
 		case QCA_WCN7850:
 			snprintf(config.fwname, sizeof(config.fwname),
@@ -862,8 +849,26 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 
 	err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
 	if (err < 0) {
-		bt_dev_err(hdev, "QCA Failed to download patch (%d)", err);
-		return err;
+		/* For WCN6750, if mbn file is not present then check for tlv file.*/
+		if (soc_type == QCA_WCN6750 && config.type == ELF_TYPE_PATCH) {
+			bt_dev_dbg(hdev, "QCA Failed to request file: %s (%d)",
+				   config.fwname, err);
+			config.type = TLV_TYPE_PATCH;
+			snprintf(config.fwname, sizeof(config.fwname),
+				 "qca/msbtfw%02x.tlv", rom_ver);
+			bt_dev_info(hdev, "QCA Downloading %s", config.fwname);
+			err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
+		} else if (!rampatch_name && soc_type == QCA_WCN6855) {
+			snprintf(config.fwname, sizeof(config.fwname),
+				 "qca/hpbtfw%02x.tlv", rom_ver);
+			err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
+		}
+
+		if (err) {
+			bt_dev_err(hdev, "QCA Failed to request file: %s (%d)",
+				   config.fwname, err);
+			return err;
+		}
 	}
 
 	/* Give the controller some time to get ready to receive the NVM */
@@ -923,7 +928,7 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 		case QCA_WCN6855:
 			qca_read_fw_board_id(hdev, &boardid);
 			qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
-						  "hpnv", soc_type, ver, rom_ver, boardid);
+						  "wcnhpnv", soc_type, ver, rom_ver, boardid);
 			break;
 		case QCA_WCN7850:
 			qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
@@ -937,8 +942,15 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 
 	err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
 	if (err < 0) {
-		bt_dev_err(hdev, "QCA Failed to download NVM (%d)", err);
-		return err;
+		if (!firmware_name && err < 0 && soc_type == QCA_WCN6855) {
+			qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
+						  "hpnv", soc_type, ver, rom_ver, boardid);
+			err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
+			if (err < 0) {
+				bt_dev_err(hdev, "QCA Failed to download NVM (%d)", err);
+				return err;
+			}
+		}
 	}
 
 	switch (soc_type) {
-- 
2.34.1

RE: Bluetooth: btqca: Add WCN6855 firmware priority selection feature

[bluez.test.bot]

[-- Attachment #1: Type: text/plain, Size: 2593 bytes --]

This is automated email and please do not reply to this email!

Dear submitter,

Thank you for submitting the patches to the linux bluetooth mailing list.
This is a CI test results with your patch series:
PW Link:https://patchwork.kernel.org/project/bluetooth/list/?series=1036661

---Test result---

Test Summary:
CheckPatch                    PENDING   0.34 seconds
GitLint                       PENDING   0.29 seconds
SubjectPrefix                 PASS      0.08 seconds
BuildKernel                   PASS      25.42 seconds
CheckAllWarning               PASS      28.13 seconds
CheckSparse                   PASS      32.15 seconds
BuildKernel32                 PASS      25.62 seconds
TestRunnerSetup               PASS      561.92 seconds
TestRunner_l2cap-tester       PASS      28.15 seconds
TestRunner_iso-tester         PASS      82.27 seconds
TestRunner_bnep-tester        PASS      6.34 seconds
TestRunner_mgmt-tester        FAIL      135.86 seconds
TestRunner_rfcomm-tester      PASS      9.35 seconds
TestRunner_sco-tester         FAIL      14.73 seconds
TestRunner_ioctl-tester       PASS      10.29 seconds
TestRunner_mesh-tester        FAIL      11.65 seconds
TestRunner_smp-tester         PASS      8.53 seconds
TestRunner_userchan-tester    PASS      6.60 seconds
IncrementalBuild              PENDING   0.60 seconds

Details
##############################
Test: CheckPatch - PENDING
Desc: Run checkpatch.pl script
Output:

##############################
Test: GitLint - PENDING
Desc: Run gitlint
Output:

##############################
Test: TestRunner_mgmt-tester - FAIL
Desc: Run mgmt-tester with test-runner
Output:
Total: 494, Passed: 489 (99.0%), Failed: 1, Not Run: 4

Failed Test Cases
Read Exp Feature - Success                           Failed       0.103 seconds
##############################
Test: TestRunner_sco-tester - FAIL
Desc: Run sco-tester with test-runner
Output:
WARNING: possible circular locking dependency detected
BUG: sleeping function called from invalid context at net/core/sock.c:3782
Total: 30, Passed: 30 (100.0%), Failed: 0, Not Run: 0
##############################
Test: TestRunner_mesh-tester - FAIL
Desc: Run mesh-tester with test-runner
Output:
Total: 10, Passed: 8 (80.0%), Failed: 2, Not Run: 0

Failed Test Cases
Mesh - Send cancel - 1                               Timed out    1.828 seconds
Mesh - Send cancel - 2                               Timed out    1.996 seconds
##############################
Test: IncrementalBuild - PENDING
Desc: Incremental build with the patches in the series
Output:



---
Regards,
Linux Bluetooth

[PATCH v2 1/1] Bluetooth: btqca: Add WCN6855 firmware priority selection feature

[Shuai Zhang]

The prefix "wcn" corresponds to the WCN685x chip, while entries without
the "wcn" prefix correspond to the QCA2066 chip. There are some feature
differences between the two.

However, due to historical reasons, WCN685x chip has been using firmware
without the "wcn" prefix. The mapping between the chip and its
corresponding firmware has now been corrected.

Cc: stable@vger.kernel.org
Fixes: 30209aeff75f ("Bluetooth: qca: Expand firmware-name to load specific rampatch")
Signed-off-by: Shuai Zhang <shuai.zhang@oss.qualcomm.com>
---
 drivers/bluetooth/btqca.c | 22 ++++++++++++++++++++--
 1 file changed, 20 insertions(+), 2 deletions(-)

diff --git a/drivers/bluetooth/btqca.c b/drivers/bluetooth/btqca.c
index 7c958d606..8e0004ef7 100644
--- a/drivers/bluetooth/btqca.c
+++ b/drivers/bluetooth/btqca.c
@@ -847,8 +847,12 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 				 "qca/msbtfw%02x.mbn", rom_ver);
 			break;
 		case QCA_WCN6855:
+			/* Due to historical reasons, WCN685x chip has been using firmware
+			 * without the "wcn" prefix. The mapping between the chip and its
+			 * corresponding firmware has now been corrected.
+			 */
 			snprintf(config.fwname, sizeof(config.fwname),
-				 "qca/hpbtfw%02x.tlv", rom_ver);
+				 "qca/wcnhpbtfw%02x.tlv", rom_ver);
 			break;
 		case QCA_WCN7850:
 			snprintf(config.fwname, sizeof(config.fwname),
@@ -861,6 +865,13 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 	}
 
 	err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
+
+	if (!rampatch_name && err < 0 && soc_type == QCA_WCN6855) {
+		snprintf(config.fwname, sizeof(config.fwname),
+			 "qca/hpbtfw%02x.tlv", rom_ver);
+		err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
+	}
+
 	if (err < 0) {
 		bt_dev_err(hdev, "QCA Failed to download patch (%d)", err);
 		return err;
@@ -923,7 +934,7 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 		case QCA_WCN6855:
 			qca_read_fw_board_id(hdev, &boardid);
 			qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
-						  "hpnv", soc_type, ver, rom_ver, boardid);
+						  "wcnhpnv", soc_type, ver, rom_ver, boardid);
 			break;
 		case QCA_WCN7850:
 			qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
@@ -936,6 +947,13 @@ int qca_uart_setup(struct hci_dev *hdev, uint8_t baudrate,
 	}
 
 	err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
+
+	if (!firmware_name && err < 0 && soc_type == QCA_WCN6855) {
+		qca_get_nvm_name_by_board(config.fwname, sizeof(config.fwname),
+					  "hpnv", soc_type, ver, rom_ver, boardid);
+		err = qca_download_firmware(hdev, &config, soc_type, rom_ver);
+	}
+
 	if (err < 0) {
 		bt_dev_err(hdev, "QCA Failed to download NVM (%d)", err);
 		return err;
-- 
2.34.1

RE: Bluetooth: btqca: Add WCN6855 firmware priority selection feature

[bluez.test.bot]

[-- Attachment #1: Type: text/plain, Size: 2457 bytes --]

This is automated email and please do not reply to this email!

Dear submitter,

Thank you for submitting the patches to the linux bluetooth mailing list.
This is a CI test results with your patch series:
PW Link:https://patchwork.kernel.org/project/bluetooth/list/?series=1023378

---Test result---

Test Summary:
CheckPatch                    PENDING   0.29 seconds
GitLint                       PENDING   0.24 seconds
SubjectPrefix                 PASS      0.12 seconds
BuildKernel                   PASS      25.23 seconds
CheckAllWarning               PASS      27.58 seconds
CheckSparse                   PASS      31.32 seconds
BuildKernel32                 PASS      24.71 seconds
TestRunnerSetup               PASS      498.02 seconds
TestRunner_l2cap-tester       PASS      23.91 seconds
TestRunner_iso-tester         PASS      58.39 seconds
TestRunner_bnep-tester        PASS      6.20 seconds
TestRunner_mgmt-tester        FAIL      118.81 seconds
TestRunner_rfcomm-tester      PASS      9.34 seconds
TestRunner_sco-tester         PASS      14.36 seconds
TestRunner_ioctl-tester       PASS      10.09 seconds
TestRunner_mesh-tester        FAIL      11.48 seconds
TestRunner_smp-tester         PASS      8.53 seconds
TestRunner_userchan-tester    PASS      6.53 seconds
IncrementalBuild              PENDING   0.46 seconds

Details
##############################
Test: CheckPatch - PENDING
Desc: Run checkpatch.pl script
Output:

##############################
Test: GitLint - PENDING
Desc: Run gitlint
Output:

##############################
Test: TestRunner_mgmt-tester - FAIL
Desc: Run mgmt-tester with test-runner
Output:
Total: 492, Passed: 485 (98.6%), Failed: 3, Not Run: 4

Failed Test Cases
Read Exp Feature - Success                           Failed       0.102 seconds
LL Privacy - Add Device 2 (2 Devices to AL)          Failed       0.163 seconds
LL Privacy - Set Flags 1 (Add to RL)                 Failed       0.152 seconds
##############################
Test: TestRunner_mesh-tester - FAIL
Desc: Run mesh-tester with test-runner
Output:
Total: 10, Passed: 8 (80.0%), Failed: 2, Not Run: 0

Failed Test Cases
Mesh - Send cancel - 1                               Timed out    1.921 seconds
Mesh - Send cancel - 2                               Timed out    1.997 seconds
##############################
Test: IncrementalBuild - PENDING
Desc: Incremental build with the patches in the series
Output:



---
Regards,
Linux Bluetooth