Re: [PATCH 2/2] thermal: amlogic: Add support for A9 thermal controller

[Daniel Lezcano <daniel.lezcano@oss.qualcomm.com>]

On 7/30/26 10:34, Xianwei Zhao via B4 Relay wrote:
> From: Xianwei Zhao <xianwei.zhao@amlogic.com>
> 
> Add support for the Amlogic A9 thermal controller.
> 
> The A9 thermal controller uses different calibration parameters, requires
> separate core and bus clocks, and supports a hardware over-temperature
> reset mechanism.
> 
> Add the A9 calibration data, retrieve the clocks by name, and configure
> the hardware reset temperature through the optional 'amlogic,hw-reset-temp'
> DT property. When the property is absent, use the default reset temperature
> of 110°C.
> 
> Also restore the hardware reset configuration after resume.
> 
> Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
> ---
>   drivers/thermal/amlogic_thermal.c | 107 ++++++++++++++++++++++++++++++++++++--
>   1 file changed, 104 insertions(+), 3 deletions(-)
> 
> diff --git a/drivers/thermal/amlogic_thermal.c b/drivers/thermal/amlogic_thermal.c
> index a0b530624b60..c9c351496653 100644
> --- a/drivers/thermal/amlogic_thermal.c
> +++ b/drivers/thermal/amlogic_thermal.c
> @@ -45,6 +45,18 @@
>   		 TSENSOR_CFG_REG1_DEM_EN |	\
>   		 TSENSOR_CFG_REG1_CH_SEL)
>   
> +#define TSENSOR_CFG_REG2			0x8
> +	#define TSENSOR_CFG_REG2_HITEMP_EN	BIT(31)
> +	#define TSENSOR_CFG_REG2_REBOOT_EN	BIT(30)
> +	#define TSENSOR_CFG_REG2_REBOOT_CODE	GENMASK(15, 4)
> +	#define TSENSOR_CFG_REG2_REBOOT_TIME	GENMASK(23, 16)
> +	#define TSENSOR_CFG_REG2_ENABLE		\
> +		(TSENSOR_CFG_REG2_HITEMP_EN |	\
> +		 TSENSOR_CFG_REG2_REBOOT_EN |	\
> +		 TSENSOR_CFG_REG2_REBOOT_TIME)
> +
> +#define TSENSOR_TEMP_CAL		1
> +
>   #define TSENSOR_STAT0			0x40
>   
>   #define TSENSOR_STAT9			0x64
> @@ -63,6 +75,7 @@
>   
>   #define TSENSOR_CALIB_OFFSET	1
>   #define TSENSOR_CALIB_SHIFT	4
> +#define TSENSOR_HW_RESET_DEFAULT_TEMP	110000
>   
>   /**
>    * struct amlogic_thermal_soc_calib_data
> @@ -93,6 +106,7 @@ struct amlogic_thermal_data {
>   	const struct amlogic_thermal_soc_calib_data *calibration_parameters;
>   	const struct regmap_config *regmap_config;
>   	bool use_sm;
> +	bool has_sysclk;
>   };
>   
>   struct amlogic_thermal {
> @@ -101,8 +115,10 @@ struct amlogic_thermal {
>   	struct regmap *regmap;
>   	struct regmap *sec_ao_map;
>   	struct clk *clk;
> +	struct clk *sysclk;
>   	struct thermal_zone_device *tzd;
>   	u32 trim_info;
> +	u32 temp_code;
>   	struct meson_sm_firmware *sm_fw;
>   	u32 tsensor_id;
>   };
> @@ -138,6 +154,46 @@ static int amlogic_thermal_code_to_millicelsius(struct amlogic_thermal *pdata,
>   	return temp;
>   }
>   
> +/*
> + * Calculate a temperature code from a temperature value .
> + * The unit of the temperature is degree milliCelsius.
> + */
> +static u32 amlogic_thermal_millicelsius_to_code(struct amlogic_thermal *pdata, int millicelsius)
> +{
> +	const struct amlogic_thermal_soc_calib_data *param =
> +					pdata->data->calibration_parameters;
> +	s64 factor, uptat, uefuse;
> +	u32 temp_code;
> +
> +	uefuse = pdata->trim_info & TSENSOR_TRIM_SIGN_MASK ?
> +			     ~(pdata->trim_info & TSENSOR_TRIM_TEMP_MASK) + 1 :
> +			     (pdata->trim_info & TSENSOR_TRIM_TEMP_MASK);
> +
> +	factor = param->B + div_s64(millicelsius, 100);
> +	factor = BIT(16) * factor;
> +	factor = div_s64(factor, param->A);
> +	factor = factor - (uefuse & TSENSOR_TRIM_TEMP_MASK);
> +
> +	uptat = param->n * factor;
> +	uptat = div_s64(uptat, BIT(16));
> +	uptat = param->m - uptat;
> +
> +	factor = factor * 100;
> +	factor = div_s64(factor, uptat);
> +
> +	temp_code = ((factor >> 0x4) & TSENSOR_TEMP_MASK) + TSENSOR_TEMP_CAL;
> +
> +	return temp_code;
> +}
> +
> +static void amlogic_tsensor_setup_hw_reset(struct amlogic_thermal *data)
> +{
> +	regmap_update_bits(data->regmap, TSENSOR_CFG_REG2, TSENSOR_CFG_REG2_REBOOT_CODE,
> +			   data->temp_code << 0x4);
> +	regmap_update_bits(data->regmap, TSENSOR_CFG_REG2,
> +			   TSENSOR_CFG_REG2_ENABLE, TSENSOR_CFG_REG2_ENABLE);
> +}
> +
>   static int amlogic_thermal_enable(struct amlogic_thermal *data)
>   {
>   	int ret;
> @@ -254,6 +310,13 @@ static const struct amlogic_thermal_soc_calib_data amlogic_thermal_g12a = {
>   	.n = 324,
>   };
>   
> +static const struct amlogic_thermal_soc_calib_data amlogic_thermal_a9 = {
> +	.A = 9164,
> +	.B = 2747,
> +	.m = 370,
> +	.n = 270,
> +};
> +
>   static const struct amlogic_thermal_data amlogic_thermal_g12a_cpu_param = {
>   	.u_efuse_off = 0x128,
>   	.calibration_parameters = &amlogic_thermal_g12a,
> @@ -272,6 +335,13 @@ static const struct amlogic_thermal_data amlogic_thermal_a1_cpu_param = {
>   	.regmap_config = &amlogic_thermal_regmap_config_g12a,
>   };
>   
> +static const struct amlogic_thermal_data amlogic_thermal_a9_param = {
> +	.use_sm			= true,
> +	.has_sysclk		= true,
> +	.calibration_parameters	= &amlogic_thermal_a9,
> +	.regmap_config		= &amlogic_thermal_regmap_config_g12a,
> +};
> +
>   static const struct amlogic_thermal_data amlogic_thermal_t7_param = {
>   	.use_sm			= true,
>   	.calibration_parameters	= &amlogic_thermal_g12a,
> @@ -291,6 +361,10 @@ static const struct of_device_id of_amlogic_thermal_match[] = {
>   		.compatible = "amlogic,a1-cpu-thermal",
>   		.data = &amlogic_thermal_a1_cpu_param,
>   	},
> +	{
> +		.compatible = "amlogic,a9-thermal",
> +		.data = &amlogic_thermal_a9_param,
> +	},
>   	{
>   		.compatible = "amlogic,t7-thermal",
>   		.data = &amlogic_thermal_t7_param,
> @@ -305,6 +379,7 @@ static int amlogic_thermal_probe(struct platform_device *pdev)
>   	struct device *dev = &pdev->dev;
>   	void __iomem *base;
>   	int ret;
> +	u32 reset_temp;
>   
>   	pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
>   	if (!pdata)
> @@ -323,9 +398,24 @@ static int amlogic_thermal_probe(struct platform_device *pdev)
>   	if (IS_ERR(pdata->regmap))
>   		return PTR_ERR(pdata->regmap);
>   
> -	pdata->clk = devm_clk_get(dev, NULL);
> -	if (IS_ERR(pdata->clk))
> -		return dev_err_probe(dev, PTR_ERR(pdata->clk), "failed to get clock\n");
> +	if (pdata->data->has_sysclk) {
> +		pdata->clk = devm_clk_get(dev, "core");
> +		if (IS_ERR(pdata->clk))
> +			return dev_err_probe(dev, PTR_ERR(pdata->clk), "failed to get core clk\n");
> +		pdata->sysclk = devm_clk_get_enabled(dev, "pclk");
> +		if (IS_ERR(pdata->sysclk))
> +			return dev_err_probe(dev, PTR_ERR(pdata->sysclk), "failed to get pclk\n");
> +	} else {
> +		pdata->clk = devm_clk_get(dev, NULL);
> +		if (IS_ERR(pdata->clk))
> +			return dev_err_probe(dev, PTR_ERR(pdata->clk), "failed to get clock\n");
> +	}
> +
> +	if (of_property_read_u32(pdev->dev.of_node, "amlogic,hw-reset-temp", &reset_temp)) {
> +		dev_dbg(dev, "using default hardware reset temperature\n");
> +		reset_temp = TSENSOR_HW_RESET_DEFAULT_TEMP;
> +	}

Old SoC without the 'amlogic,hw-reset-temp' will now default to 
TSENSOR_HW_RESET_DEFAULT_TEMP

> +
>   
>   	if (pdata->data->use_sm)
>   		ret = amlogic_thermal_probe_sm(pdev, pdata);
> @@ -346,6 +436,10 @@ static int amlogic_thermal_probe(struct platform_device *pdev)
>   
>   	devm_thermal_add_hwmon_sysfs(&pdev->dev, pdata->tzd);
>   
> +	pdata->temp_code = amlogic_thermal_millicelsius_to_code(pdata, reset_temp);
> +
> +	amlogic_tsensor_setup_hw_reset(pdata);

Somehow related to the above comment, should it be only for A9 ?

> +
>   	ret = amlogic_thermal_enable(pdata);
>   
>   	return ret;
> @@ -355,6 +449,8 @@ static void amlogic_thermal_remove(struct platform_device *pdev)
>   {
>   	struct amlogic_thermal *data = platform_get_drvdata(pdev);
>   
> +	if (data->data->has_sysclk)
> +		clk_disable_unprepare(data->sysclk);

Not needed, devm_ is used in the probe function

>   	amlogic_thermal_disable(data);
>   }
>   
> @@ -363,6 +459,8 @@ static int amlogic_thermal_suspend(struct device *dev)
>   	struct amlogic_thermal *data = dev_get_drvdata(dev);
>   
>   	amlogic_thermal_disable(data);
> +	if (data->data->has_sysclk)
> +		clk_disable_unprepare(data->sysclk);
>   
>   	return 0;
>   }
> @@ -371,6 +469,9 @@ static int amlogic_thermal_resume(struct device *dev)
>   {
>   	struct amlogic_thermal *data = dev_get_drvdata(dev);
>   
> +	amlogic_tsensor_setup_hw_reset(data);
> +	if (data->data->has_sysclk)
> +		clk_prepare_enable(data->sysclk);

Shouldn't the clock enabled before accessing the register in 
amlogic_tsensor_setup_hw_reset() ?

>   	return amlogic_thermal_enable(data);
>   }
>   
> 


_______________________________________________
linux-amlogic mailing list
linux-amlogic@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-amlogic