* [PATCH v2 1/2] arm64: dts: rockchip: add usb3 controller node for RK3328 SoCs
@ 2017-08-17 7:54 ` William Wu
0 siblings, 0 replies; 12+ messages in thread
From: William Wu @ 2017-08-17 7:54 UTC (permalink / raw)
To: heiko
Cc: robh+dt, mark.rutland, linux, linux-arm-kernel, devicetree,
linux-kernel, linux-rockchip, frank.wang, huangtao, daniel.meng,
william.wu
RK3328 has one USB 3.0 OTG controller which uses DWC_USB3
core's general architecture. It can act as static xHCI host
controller, static device controller, USB 3.0/2.0 OTG basing
on ID of USB3.0 PHY.
Signed-off-by: William Wu <william.wu@rock-chips.com>
---
Changes in v2:
- Modify the dwc3 quirk "snps,tx-ipgap-linecheck-dis-quirk" to
"snps,dis-tx-ipgap-linecheck-quirk"
.../devicetree/bindings/usb/rockchip,dwc3.txt | 4 +++-
arch/arm64/boot/dts/rockchip/rk3328.dtsi | 27 ++++++++++++++++++++++
2 files changed, 30 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt
index 0536a93..d6b2e47 100644
--- a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt
+++ b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt
@@ -1,7 +1,9 @@
Rockchip SuperSpeed DWC3 USB SoC controller
Required properties:
-- compatible: should contain "rockchip,rk3399-dwc3" for rk3399 SoC
+- compatible: should be one of the following:
+ - "rockchip,rk3399-dwc3": for rk3399 SoC
+ - "rockchip,rk3328-dwc3", "rockchip,rk3399-dwc3": for rk3328 SoC
- clocks: A list of phandle + clock-specifier pairs for the
clocks listed in clock-names
- clock-names: Should contain the following:
diff --git a/arch/arm64/boot/dts/rockchip/rk3328.dtsi b/arch/arm64/boot/dts/rockchip/rk3328.dtsi
index e6da0ce..14bd8f4 100644
--- a/arch/arm64/boot/dts/rockchip/rk3328.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3328.dtsi
@@ -655,6 +655,33 @@
status = "disabled";
};
+ usbdrd3: usb@ff600000 {
+ compatible = "rockchip,rk3328-dwc3", "rockchip,rk3399-dwc3";
+ clocks = <&cru SCLK_USB3OTG_REF>, <&cru SCLK_USB3OTG_SUSPEND>,
+ <&cru ACLK_USB3OTG>;
+ clock-names = "ref_clk", "suspend_clk",
+ "bus_clk";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ status = "disabled";
+
+ usbdrd_dwc3: dwc3@ff600000 {
+ compatible = "snps,dwc3";
+ reg = <0x0 0xff600000 0x0 0x100000>;
+ interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+ dr_mode = "otg";
+ phy_type = "utmi_wide";
+ snps,dis_enblslpm_quirk;
+ snps,dis-u2-freeclk-exists-quirk;
+ snps,dis_u2_susphy_quirk;
+ snps,dis_u3_susphy_quirk;
+ snps,dis-del-phy-power-chg-quirk;
+ snps,dis-tx-ipgap-linecheck-quirk;
+ status = "disabled";
+ };
+ };
+
gic: interrupt-controller@ff811000 {
compatible = "arm,gic-400";
#interrupt-cells = <3>;
--
2.0.0
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH v2 1/2] arm64: dts: rockchip: add usb3 controller node for RK3328 SoCs
@ 2017-08-17 7:54 ` William Wu
0 siblings, 0 replies; 12+ messages in thread
From: William Wu @ 2017-08-17 7:54 UTC (permalink / raw)
To: linux-arm-kernel
RK3328 has one USB 3.0 OTG controller which uses DWC_USB3
core's general architecture. It can act as static xHCI host
controller, static device controller, USB 3.0/2.0 OTG basing
on ID of USB3.0 PHY.
Signed-off-by: William Wu <william.wu@rock-chips.com>
---
Changes in v2:
- Modify the dwc3 quirk "snps,tx-ipgap-linecheck-dis-quirk" to
"snps,dis-tx-ipgap-linecheck-quirk"
.../devicetree/bindings/usb/rockchip,dwc3.txt | 4 +++-
arch/arm64/boot/dts/rockchip/rk3328.dtsi | 27 ++++++++++++++++++++++
2 files changed, 30 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt
index 0536a93..d6b2e47 100644
--- a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt
+++ b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt
@@ -1,7 +1,9 @@
Rockchip SuperSpeed DWC3 USB SoC controller
Required properties:
-- compatible: should contain "rockchip,rk3399-dwc3" for rk3399 SoC
+- compatible: should be one of the following:
+ - "rockchip,rk3399-dwc3": for rk3399 SoC
+ - "rockchip,rk3328-dwc3", "rockchip,rk3399-dwc3": for rk3328 SoC
- clocks: A list of phandle + clock-specifier pairs for the
clocks listed in clock-names
- clock-names: Should contain the following:
diff --git a/arch/arm64/boot/dts/rockchip/rk3328.dtsi b/arch/arm64/boot/dts/rockchip/rk3328.dtsi
index e6da0ce..14bd8f4 100644
--- a/arch/arm64/boot/dts/rockchip/rk3328.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3328.dtsi
@@ -655,6 +655,33 @@
status = "disabled";
};
+ usbdrd3: usb at ff600000 {
+ compatible = "rockchip,rk3328-dwc3", "rockchip,rk3399-dwc3";
+ clocks = <&cru SCLK_USB3OTG_REF>, <&cru SCLK_USB3OTG_SUSPEND>,
+ <&cru ACLK_USB3OTG>;
+ clock-names = "ref_clk", "suspend_clk",
+ "bus_clk";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ status = "disabled";
+
+ usbdrd_dwc3: dwc3 at ff600000 {
+ compatible = "snps,dwc3";
+ reg = <0x0 0xff600000 0x0 0x100000>;
+ interrupts = <GIC_SPI 67 IRQ_TYPE_LEVEL_HIGH>;
+ dr_mode = "otg";
+ phy_type = "utmi_wide";
+ snps,dis_enblslpm_quirk;
+ snps,dis-u2-freeclk-exists-quirk;
+ snps,dis_u2_susphy_quirk;
+ snps,dis_u3_susphy_quirk;
+ snps,dis-del-phy-power-chg-quirk;
+ snps,dis-tx-ipgap-linecheck-quirk;
+ status = "disabled";
+ };
+ };
+
gic: interrupt-controller at ff811000 {
compatible = "arm,gic-400";
#interrupt-cells = <3>;
--
2.0.0
^ permalink raw reply related [flat|nested] 12+ messages in thread* Re: [PATCH v2 1/2] arm64: dts: rockchip: add usb3 controller node for RK3328 SoCs
2017-08-17 7:54 ` William Wu
@ 2017-08-18 9:24 ` Heiko Stuebner
-1 siblings, 0 replies; 12+ messages in thread
From: Heiko Stuebner @ 2017-08-18 9:24 UTC (permalink / raw)
To: William Wu
Cc: robh+dt, mark.rutland, linux, linux-arm-kernel, devicetree,
linux-kernel, linux-rockchip, frank.wang, huangtao, daniel.meng
Hi William,
Am Donnerstag, 17. August 2017, 15:54:49 CEST schrieb William Wu:
> RK3328 has one USB 3.0 OTG controller which uses DWC_USB3
> core's general architecture. It can act as static xHCI host
> controller, static device controller, USB 3.0/2.0 OTG basing
> on ID of USB3.0 PHY.
>
> Signed-off-by: William Wu <william.wu@rock-chips.com>
> ---
> Changes in v2:
> - Modify the dwc3 quirk "snps,tx-ipgap-linecheck-dis-quirk" to
> "snps,dis-tx-ipgap-linecheck-quirk"
>
> .../devicetree/bindings/usb/rockchip,dwc3.txt | 4 +++-
> arch/arm64/boot/dts/rockchip/rk3328.dtsi | 27 ++++++++++++++++++++++
> 2 files changed, 30 insertions(+), 1 deletion(-)
>
> diff --git a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt
> index 0536a93..d6b2e47 100644
> --- a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt
> +++ b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt
> @@ -1,7 +1,9 @@
> Rockchip SuperSpeed DWC3 USB SoC controller
>
> Required properties:
> -- compatible: should contain "rockchip,rk3399-dwc3" for rk3399 SoC
> +- compatible: should be one of the following:
> + - "rockchip,rk3399-dwc3": for rk3399 SoC
> + - "rockchip,rk3328-dwc3", "rockchip,rk3399-dwc3": for rk3328 SoC
> - clocks: A list of phandle + clock-specifier pairs for the
> clocks listed in clock-names
> - clock-names: Should contain the following:
This probably shouldn't be part of the patch adding the dts node, but
instead should be a separate patch and should either go through some
usb tree or at least get an Ack from usb maintainers (Felipe Balbi and/or
Greg Kroah Hartman), so you should definitly include them into your
recipient list.
Heiko
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v2 1/2] arm64: dts: rockchip: add usb3 controller node for RK3328 SoCs
@ 2017-08-18 9:24 ` Heiko Stuebner
0 siblings, 0 replies; 12+ messages in thread
From: Heiko Stuebner @ 2017-08-18 9:24 UTC (permalink / raw)
To: linux-arm-kernel
Hi William,
Am Donnerstag, 17. August 2017, 15:54:49 CEST schrieb William Wu:
> RK3328 has one USB 3.0 OTG controller which uses DWC_USB3
> core's general architecture. It can act as static xHCI host
> controller, static device controller, USB 3.0/2.0 OTG basing
> on ID of USB3.0 PHY.
>
> Signed-off-by: William Wu <william.wu@rock-chips.com>
> ---
> Changes in v2:
> - Modify the dwc3 quirk "snps,tx-ipgap-linecheck-dis-quirk" to
> "snps,dis-tx-ipgap-linecheck-quirk"
>
> .../devicetree/bindings/usb/rockchip,dwc3.txt | 4 +++-
> arch/arm64/boot/dts/rockchip/rk3328.dtsi | 27 ++++++++++++++++++++++
> 2 files changed, 30 insertions(+), 1 deletion(-)
>
> diff --git a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt
> index 0536a93..d6b2e47 100644
> --- a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt
> +++ b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt
> @@ -1,7 +1,9 @@
> Rockchip SuperSpeed DWC3 USB SoC controller
>
> Required properties:
> -- compatible: should contain "rockchip,rk3399-dwc3" for rk3399 SoC
> +- compatible: should be one of the following:
> + - "rockchip,rk3399-dwc3": for rk3399 SoC
> + - "rockchip,rk3328-dwc3", "rockchip,rk3399-dwc3": for rk3328 SoC
> - clocks: A list of phandle + clock-specifier pairs for the
> clocks listed in clock-names
> - clock-names: Should contain the following:
This probably shouldn't be part of the patch adding the dts node, but
instead should be a separate patch and should either go through some
usb tree or at least get an Ack from usb maintainers (Felipe Balbi and/or
Greg Kroah Hartman), so you should definitly include them into your
recipient list.
Heiko
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v2 1/2] arm64: dts: rockchip: add usb3 controller node for RK3328 SoCs
2017-08-18 9:24 ` Heiko Stuebner
(?)
@ 2017-08-21 11:35 ` wlf
-1 siblings, 0 replies; 12+ messages in thread
From: wlf @ 2017-08-21 11:35 UTC (permalink / raw)
To: Heiko Stuebner, William Wu
Cc: robh+dt-DgEjT+Ai2ygdnm+yROfE0A, mark.rutland-5wv7dgnIgG8,
linux-I+IVW8TIWO2tmTQ+vhA3Yw,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
devicetree-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-rockchip-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
frank.wang-TNX95d0MmH7DzftRWevZcw,
huangtao-TNX95d0MmH7DzftRWevZcw,
daniel.meng-TNX95d0MmH7DzftRWevZcw
Dear Heiko,
在 2017年08月18日 17:24, Heiko Stuebner 写道:
> Hi William,
>
> Am Donnerstag, 17. August 2017, 15:54:49 CEST schrieb William Wu:
>> RK3328 has one USB 3.0 OTG controller which uses DWC_USB3
>> core's general architecture. It can act as static xHCI host
>> controller, static device controller, USB 3.0/2.0 OTG basing
>> on ID of USB3.0 PHY.
>>
>> Signed-off-by: William Wu <william.wu-TNX95d0MmH7DzftRWevZcw@public.gmane.org>
>> ---
>> Changes in v2:
>> - Modify the dwc3 quirk "snps,tx-ipgap-linecheck-dis-quirk" to
>> "snps,dis-tx-ipgap-linecheck-quirk"
>>
>> .../devicetree/bindings/usb/rockchip,dwc3.txt | 4 +++-
>> arch/arm64/boot/dts/rockchip/rk3328.dtsi | 27 ++++++++++++++++++++++
>> 2 files changed, 30 insertions(+), 1 deletion(-)
>>
>> diff --git a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt
>> index 0536a93..d6b2e47 100644
>> --- a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt
>> +++ b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt
>> @@ -1,7 +1,9 @@
>> Rockchip SuperSpeed DWC3 USB SoC controller
>>
>> Required properties:
>> -- compatible: should contain "rockchip,rk3399-dwc3" for rk3399 SoC
>> +- compatible: should be one of the following:
>> + - "rockchip,rk3399-dwc3": for rk3399 SoC
>> + - "rockchip,rk3328-dwc3", "rockchip,rk3399-dwc3": for rk3328 SoC
>> - clocks: A list of phandle + clock-specifier pairs for the
>> clocks listed in clock-names
>> - clock-names: Should contain the following:
> This probably shouldn't be part of the patch adding the dts node, but
> instead should be a separate patch and should either go through some
> usb tree or at least get an Ack from usb maintainers (Felipe Balbi and/or
> Greg Kroah Hartman), so you should definitly include them into your
> recipient list.
Thanks for your suggestion. I will submit two patches separately, and
add usb maintainers in
the recipient list.
>
>
> Heiko
>
>
>
>
--
吴良峰 William.Wu
福建省福州市铜盘路软件大道89号软件园A区21号楼
No.21 Building, A District, No.89,software Boulevard Fuzhou,Fujian, PRC
手机: 13685012275
座机: 0591-83991906-8520
邮件:wulf-TNX95d0MmH7DzftRWevZcw@public.gmane.org
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH v2 1/2] arm64: dts: rockchip: add usb3 controller node for RK3328 SoCs
@ 2017-08-21 11:35 ` wlf
0 siblings, 0 replies; 12+ messages in thread
From: wlf @ 2017-08-21 11:35 UTC (permalink / raw)
To: Heiko Stuebner, William Wu
Cc: robh+dt, mark.rutland, linux, linux-arm-kernel, devicetree,
linux-kernel, linux-rockchip, frank.wang, huangtao, daniel.meng
Dear Heiko,
在 2017年08月18日 17:24, Heiko Stuebner 写道:
> Hi William,
>
> Am Donnerstag, 17. August 2017, 15:54:49 CEST schrieb William Wu:
>> RK3328 has one USB 3.0 OTG controller which uses DWC_USB3
>> core's general architecture. It can act as static xHCI host
>> controller, static device controller, USB 3.0/2.0 OTG basing
>> on ID of USB3.0 PHY.
>>
>> Signed-off-by: William Wu <william.wu@rock-chips.com>
>> ---
>> Changes in v2:
>> - Modify the dwc3 quirk "snps,tx-ipgap-linecheck-dis-quirk" to
>> "snps,dis-tx-ipgap-linecheck-quirk"
>>
>> .../devicetree/bindings/usb/rockchip,dwc3.txt | 4 +++-
>> arch/arm64/boot/dts/rockchip/rk3328.dtsi | 27 ++++++++++++++++++++++
>> 2 files changed, 30 insertions(+), 1 deletion(-)
>>
>> diff --git a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt
>> index 0536a93..d6b2e47 100644
>> --- a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt
>> +++ b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt
>> @@ -1,7 +1,9 @@
>> Rockchip SuperSpeed DWC3 USB SoC controller
>>
>> Required properties:
>> -- compatible: should contain "rockchip,rk3399-dwc3" for rk3399 SoC
>> +- compatible: should be one of the following:
>> + - "rockchip,rk3399-dwc3": for rk3399 SoC
>> + - "rockchip,rk3328-dwc3", "rockchip,rk3399-dwc3": for rk3328 SoC
>> - clocks: A list of phandle + clock-specifier pairs for the
>> clocks listed in clock-names
>> - clock-names: Should contain the following:
> This probably shouldn't be part of the patch adding the dts node, but
> instead should be a separate patch and should either go through some
> usb tree or at least get an Ack from usb maintainers (Felipe Balbi and/or
> Greg Kroah Hartman), so you should definitly include them into your
> recipient list.
Thanks for your suggestion. I will submit two patches separately, and
add usb maintainers in
the recipient list.
>
>
> Heiko
>
>
>
>
--
吴良峰 William.Wu
福建省福州市铜盘路软件大道89号软件园A区21号楼
No.21 Building, A District, No.89,software Boulevard Fuzhou,Fujian, PRC
手机: 13685012275
座机: 0591-83991906-8520
邮件:wulf@rock-chips.com
^ permalink raw reply [flat|nested] 12+ messages in thread
* [PATCH v2 1/2] arm64: dts: rockchip: add usb3 controller node for RK3328 SoCs
@ 2017-08-21 11:35 ` wlf
0 siblings, 0 replies; 12+ messages in thread
From: wlf @ 2017-08-21 11:35 UTC (permalink / raw)
To: linux-arm-kernel
Dear Heiko,
? 2017?08?18? 17:24, Heiko Stuebner ??:
> Hi William,
>
> Am Donnerstag, 17. August 2017, 15:54:49 CEST schrieb William Wu:
>> RK3328 has one USB 3.0 OTG controller which uses DWC_USB3
>> core's general architecture. It can act as static xHCI host
>> controller, static device controller, USB 3.0/2.0 OTG basing
>> on ID of USB3.0 PHY.
>>
>> Signed-off-by: William Wu <william.wu@rock-chips.com>
>> ---
>> Changes in v2:
>> - Modify the dwc3 quirk "snps,tx-ipgap-linecheck-dis-quirk" to
>> "snps,dis-tx-ipgap-linecheck-quirk"
>>
>> .../devicetree/bindings/usb/rockchip,dwc3.txt | 4 +++-
>> arch/arm64/boot/dts/rockchip/rk3328.dtsi | 27 ++++++++++++++++++++++
>> 2 files changed, 30 insertions(+), 1 deletion(-)
>>
>> diff --git a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt
>> index 0536a93..d6b2e47 100644
>> --- a/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt
>> +++ b/Documentation/devicetree/bindings/usb/rockchip,dwc3.txt
>> @@ -1,7 +1,9 @@
>> Rockchip SuperSpeed DWC3 USB SoC controller
>>
>> Required properties:
>> -- compatible: should contain "rockchip,rk3399-dwc3" for rk3399 SoC
>> +- compatible: should be one of the following:
>> + - "rockchip,rk3399-dwc3": for rk3399 SoC
>> + - "rockchip,rk3328-dwc3", "rockchip,rk3399-dwc3": for rk3328 SoC
>> - clocks: A list of phandle + clock-specifier pairs for the
>> clocks listed in clock-names
>> - clock-names: Should contain the following:
> This probably shouldn't be part of the patch adding the dts node, but
> instead should be a separate patch and should either go through some
> usb tree or at least get an Ack from usb maintainers (Felipe Balbi and/or
> Greg Kroah Hartman), so you should definitly include them into your
> recipient list.
Thanks for your suggestion. I will submit two patches separately, and
add usb maintainers in
the recipient list.
>
>
> Heiko
>
>
>
>
--
??? William.Wu
?????????????89????A?21??
No.21 Building, A District, No.89,software Boulevard Fuzhou,Fujian, PRC
??: 13685012275
??: 0591-83991906-8520
??:wulf at rock-chips.com
^ permalink raw reply [flat|nested] 12+ messages in thread