[PATCH v7 0/2] Introduce MediaTek CCI devfreq driver

[PATCH v7 0/2] Introduce MediaTek CCI devfreq driver

[Johnson Wang]

The Cache Coherent Interconnect (CCI) is the management of cache
coherency by hardware. CCI DEVFREQ is DVFS driver for power saving by
scaling clock frequency and supply voltage of CCI. CCI uses the same
input clock source and power rail as LITTLE CPUs on Mediatek SoCs.

This series depends on:
Chanwoo's repo: kernel/git/chanwoo/linux.git
branch: devfreq-testing
[1]: PM / devfreq: Export devfreq_get_freq_range symbol within devfreq
[2]: PM / devfreq: Add cpu based scaling support to passive governor
[3]: PM / devfreq: passive: Reduce duplicate code when passive_devfreq case
[4]: PM / devfreq: passive: Update frequency when start governor

Changes in v7:
- remove the 'ret' printing from dev_err_probe().

Changes in v6:
- Remove unnecessary "goto" statement.

Changes in v5:
- Modify some binding description.
- Remove pre_voltage member.
- Not to enable/disable intermediate clock.
- Not to "put" resources that using devm_ variants.

Resend v4:
- CC interconnect maintainer.
- Change sign-off sequence in commit message.

Changes in v4:
- Add a maintainer in the binding document.
- Modify clock description.
- Add binding document into MAINTAINERS.
- Replace format specifier %d with %ld.

Changes in v3:
- Move binding document to 'interconnect' and rename it.
- Add COMPILE_TEST dependence symbol.
- Remove need_voltage_tracking variable.
- Move mtk_ccifreq_voltage_tracking() code into mtk_ccifreq_set_voltage().
- Add an interation limit in the while() loop.
- Replace 'cci_dev' with 'dev'
- Replace old_* with pre_*
- Remove of_match_ptr()
- Use module_platform_driver()

Changes in v2:
- Take MT8183 as example in binding document.
- Use dev_err() instead of pr_err().
- Use 'goto' statement to handle error case.
- Clean up driver code.

Johnson Wang (2):
  dt-bindings: interconnect: Add MediaTek CCI dt-bindings
  PM / devfreq: mediatek: Introduce MediaTek CCI devfreq driver

 .../bindings/interconnect/mediatek,cci.yaml   | 140 ++++++
 MAINTAINERS                                   |   1 +
 drivers/devfreq/Kconfig                       |  10 +
 drivers/devfreq/Makefile                      |   1 +
 drivers/devfreq/mtk-cci-devfreq.c             | 474 ++++++++++++++++++
 5 files changed, 626 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/interconnect/mediatek,cci.yaml
 create mode 100644 drivers/devfreq/mtk-cci-devfreq.c

-- 
2.18.0


_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

[PATCH v7 0/2] Introduce MediaTek CCI devfreq driver

[Johnson Wang]

The Cache Coherent Interconnect (CCI) is the management of cache
coherency by hardware. CCI DEVFREQ is DVFS driver for power saving by
scaling clock frequency and supply voltage of CCI. CCI uses the same
input clock source and power rail as LITTLE CPUs on Mediatek SoCs.

This series depends on:
Chanwoo's repo: kernel/git/chanwoo/linux.git
branch: devfreq-testing
[1]: PM / devfreq: Export devfreq_get_freq_range symbol within devfreq
[2]: PM / devfreq: Add cpu based scaling support to passive governor
[3]: PM / devfreq: passive: Reduce duplicate code when passive_devfreq case
[4]: PM / devfreq: passive: Update frequency when start governor

Changes in v7:
- remove the 'ret' printing from dev_err_probe().

Changes in v6:
- Remove unnecessary "goto" statement.

Changes in v5:
- Modify some binding description.
- Remove pre_voltage member.
- Not to enable/disable intermediate clock.
- Not to "put" resources that using devm_ variants.

Resend v4:
- CC interconnect maintainer.
- Change sign-off sequence in commit message.

Changes in v4:
- Add a maintainer in the binding document.
- Modify clock description.
- Add binding document into MAINTAINERS.
- Replace format specifier %d with %ld.

Changes in v3:
- Move binding document to 'interconnect' and rename it.
- Add COMPILE_TEST dependence symbol.
- Remove need_voltage_tracking variable.
- Move mtk_ccifreq_voltage_tracking() code into mtk_ccifreq_set_voltage().
- Add an interation limit in the while() loop.
- Replace 'cci_dev' with 'dev'
- Replace old_* with pre_*
- Remove of_match_ptr()
- Use module_platform_driver()

Changes in v2:
- Take MT8183 as example in binding document.
- Use dev_err() instead of pr_err().
- Use 'goto' statement to handle error case.
- Clean up driver code.

Johnson Wang (2):
  dt-bindings: interconnect: Add MediaTek CCI dt-bindings
  PM / devfreq: mediatek: Introduce MediaTek CCI devfreq driver

 .../bindings/interconnect/mediatek,cci.yaml   | 140 ++++++
 MAINTAINERS                                   |   1 +
 drivers/devfreq/Kconfig                       |  10 +
 drivers/devfreq/Makefile                      |   1 +
 drivers/devfreq/mtk-cci-devfreq.c             | 474 ++++++++++++++++++
 5 files changed, 626 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/interconnect/mediatek,cci.yaml
 create mode 100644 drivers/devfreq/mtk-cci-devfreq.c

-- 
2.18.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v7 0/2] Introduce MediaTek CCI devfreq driver

[Johnson Wang]

The Cache Coherent Interconnect (CCI) is the management of cache
coherency by hardware. CCI DEVFREQ is DVFS driver for power saving by
scaling clock frequency and supply voltage of CCI. CCI uses the same
input clock source and power rail as LITTLE CPUs on Mediatek SoCs.

This series depends on:
Chanwoo's repo: kernel/git/chanwoo/linux.git
branch: devfreq-testing
[1]: PM / devfreq: Export devfreq_get_freq_range symbol within devfreq
[2]: PM / devfreq: Add cpu based scaling support to passive governor
[3]: PM / devfreq: passive: Reduce duplicate code when passive_devfreq case
[4]: PM / devfreq: passive: Update frequency when start governor

Changes in v7:
- remove the 'ret' printing from dev_err_probe().

Changes in v6:
- Remove unnecessary "goto" statement.

Changes in v5:
- Modify some binding description.
- Remove pre_voltage member.
- Not to enable/disable intermediate clock.
- Not to "put" resources that using devm_ variants.

Resend v4:
- CC interconnect maintainer.
- Change sign-off sequence in commit message.

Changes in v4:
- Add a maintainer in the binding document.
- Modify clock description.
- Add binding document into MAINTAINERS.
- Replace format specifier %d with %ld.

Changes in v3:
- Move binding document to 'interconnect' and rename it.
- Add COMPILE_TEST dependence symbol.
- Remove need_voltage_tracking variable.
- Move mtk_ccifreq_voltage_tracking() code into mtk_ccifreq_set_voltage().
- Add an interation limit in the while() loop.
- Replace 'cci_dev' with 'dev'
- Replace old_* with pre_*
- Remove of_match_ptr()
- Use module_platform_driver()

Changes in v2:
- Take MT8183 as example in binding document.
- Use dev_err() instead of pr_err().
- Use 'goto' statement to handle error case.
- Clean up driver code.

Johnson Wang (2):
  dt-bindings: interconnect: Add MediaTek CCI dt-bindings
  PM / devfreq: mediatek: Introduce MediaTek CCI devfreq driver

 .../bindings/interconnect/mediatek,cci.yaml   | 140 ++++++
 MAINTAINERS                                   |   1 +
 drivers/devfreq/Kconfig                       |  10 +
 drivers/devfreq/Makefile                      |   1 +
 drivers/devfreq/mtk-cci-devfreq.c             | 474 ++++++++++++++++++
 5 files changed, 626 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/interconnect/mediatek,cci.yaml
 create mode 100644 drivers/devfreq/mtk-cci-devfreq.c

-- 
2.18.0

[PATCH v7 1/2] dt-bindings: interconnect: Add MediaTek CCI dt-bindings

[Johnson Wang]

Add devicetree binding of MediaTek CCI on MT8183 and MT8186.

Signed-off-by: Jia-Wei Chang <jia-wei.chang@mediatek.com>
Signed-off-by: Johnson Wang <johnson.wang@mediatek.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Georgi Djakov <djakov@kernel.org>
---
 .../bindings/interconnect/mediatek,cci.yaml   | 141 ++++++++++++++++++
 MAINTAINERS                                   |   1 +
 2 files changed, 142 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/interconnect/mediatek,cci.yaml

diff --git a/Documentation/devicetree/bindings/interconnect/mediatek,cci.yaml b/Documentation/devicetree/bindings/interconnect/mediatek,cci.yaml
new file mode 100644
index 000000000000..449c7c988229
--- /dev/null
+++ b/Documentation/devicetree/bindings/interconnect/mediatek,cci.yaml
@@ -0,0 +1,141 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/interconnect/mediatek,cci.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek Cache Coherent Interconnect (CCI) frequency and voltage scaling
+
+maintainers:
+  - Jia-Wei Chang <jia-wei.chang@mediatek.com>
+  - Johnson Wang <johnson.wang@mediatek.com>
+
+description: |
+  MediaTek Cache Coherent Interconnect (CCI) is a hardware engine used by
+  MT8183 and MT8186 SoCs to scale the frequency and adjust the voltage in
+  hardware. It can also optimize the voltage to reduce the power consumption.
+
+properties:
+  compatible:
+    enum:
+      - mediatek,mt8183-cci
+      - mediatek,mt8186-cci
+
+  clocks:
+    items:
+      - description:
+          The multiplexer for clock input of the bus.
+      - description:
+          A parent of "bus" clock which is used as an intermediate clock source
+          when the original clock source (PLL) is under transition and not
+          stable yet.
+
+  clock-names:
+    items:
+      - const: cci
+      - const: intermediate
+
+  operating-points-v2: true
+  opp-table: true
+
+  proc-supply:
+    description:
+      Phandle of the regulator for CCI that provides the supply voltage.
+
+  sram-supply:
+    description:
+      Phandle of the regulator for sram of CCI that provides the supply
+      voltage. When it is present, the implementation needs to do
+      "voltage tracking" to step by step scale up/down Vproc and Vsram to fit
+      SoC specific needs. When absent, the voltage scaling flow is handled by
+      hardware, hence no software "voltage tracking" is needed.
+
+required:
+  - compatible
+  - clocks
+  - clock-names
+  - operating-points-v2
+  - proc-supply
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/mt8183-clk.h>
+    cci: cci {
+        compatible = "mediatek,mt8183-cci";
+        clocks = <&mcucfg CLK_MCU_BUS_SEL>,
+                 <&topckgen CLK_TOP_ARMPLL_DIV_PLL1>;
+        clock-names = "cci", "intermediate";
+        operating-points-v2 = <&cci_opp>;
+        proc-supply = <&mt6358_vproc12_reg>;
+    };
+
+    cci_opp: opp-table-cci {
+        compatible = "operating-points-v2";
+        opp-shared;
+        opp2_00: opp-273000000 {
+            opp-hz = /bits/ 64 <273000000>;
+            opp-microvolt = <650000>;
+        };
+        opp2_01: opp-338000000 {
+            opp-hz = /bits/ 64 <338000000>;
+            opp-microvolt = <687500>;
+        };
+        opp2_02: opp-403000000 {
+            opp-hz = /bits/ 64 <403000000>;
+            opp-microvolt = <718750>;
+        };
+        opp2_03: opp-463000000 {
+            opp-hz = /bits/ 64 <463000000>;
+            opp-microvolt = <756250>;
+        };
+        opp2_04: opp-546000000 {
+            opp-hz = /bits/ 64 <546000000>;
+            opp-microvolt = <800000>;
+        };
+        opp2_05: opp-624000000 {
+            opp-hz = /bits/ 64 <624000000>;
+            opp-microvolt = <818750>;
+        };
+        opp2_06: opp-689000000 {
+            opp-hz = /bits/ 64 <689000000>;
+            opp-microvolt = <850000>;
+        };
+        opp2_07: opp-767000000 {
+            opp-hz = /bits/ 64 <767000000>;
+            opp-microvolt = <868750>;
+        };
+        opp2_08: opp-845000000 {
+            opp-hz = /bits/ 64 <845000000>;
+            opp-microvolt = <893750>;
+        };
+        opp2_09: opp-871000000 {
+            opp-hz = /bits/ 64 <871000000>;
+            opp-microvolt = <906250>;
+        };
+        opp2_10: opp-923000000 {
+            opp-hz = /bits/ 64 <923000000>;
+            opp-microvolt = <931250>;
+        };
+        opp2_11: opp-962000000 {
+            opp-hz = /bits/ 64 <962000000>;
+            opp-microvolt = <943750>;
+        };
+        opp2_12: opp-1027000000 {
+            opp-hz = /bits/ 64 <1027000000>;
+            opp-microvolt = <975000>;
+        };
+        opp2_13: opp-1092000000 {
+            opp-hz = /bits/ 64 <1092000000>;
+            opp-microvolt = <1000000>;
+        };
+        opp2_14: opp-1144000000 {
+            opp-hz = /bits/ 64 <1144000000>;
+            opp-microvolt = <1025000>;
+        };
+        opp2_15: opp-1196000000 {
+            opp-hz = /bits/ 64 <1196000000>;
+            opp-microvolt = <1050000>;
+        };
+    };
diff --git a/MAINTAINERS b/MAINTAINERS
index b54288db77aa..2800ddceb54c 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -5757,6 +5757,7 @@ L:	linux-pm@vger.kernel.org
 S:	Maintained
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/linux.git
 F:	Documentation/devicetree/bindings/devfreq/
+F:	Documentation/devicetree/bindings/interconnect/mediatek,cci.yaml
 F:	drivers/devfreq/
 F:	include/linux/devfreq.h
 F:	include/trace/events/devfreq.h
-- 
2.18.0


_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

[PATCH v7 1/2] dt-bindings: interconnect: Add MediaTek CCI dt-bindings

[Johnson Wang]

Add devicetree binding of MediaTek CCI on MT8183 and MT8186.

Signed-off-by: Jia-Wei Chang <jia-wei.chang@mediatek.com>
Signed-off-by: Johnson Wang <johnson.wang@mediatek.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Georgi Djakov <djakov@kernel.org>
---
 .../bindings/interconnect/mediatek,cci.yaml   | 141 ++++++++++++++++++
 MAINTAINERS                                   |   1 +
 2 files changed, 142 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/interconnect/mediatek,cci.yaml

diff --git a/Documentation/devicetree/bindings/interconnect/mediatek,cci.yaml b/Documentation/devicetree/bindings/interconnect/mediatek,cci.yaml
new file mode 100644
index 000000000000..449c7c988229
--- /dev/null
+++ b/Documentation/devicetree/bindings/interconnect/mediatek,cci.yaml
@@ -0,0 +1,141 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/interconnect/mediatek,cci.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek Cache Coherent Interconnect (CCI) frequency and voltage scaling
+
+maintainers:
+  - Jia-Wei Chang <jia-wei.chang@mediatek.com>
+  - Johnson Wang <johnson.wang@mediatek.com>
+
+description: |
+  MediaTek Cache Coherent Interconnect (CCI) is a hardware engine used by
+  MT8183 and MT8186 SoCs to scale the frequency and adjust the voltage in
+  hardware. It can also optimize the voltage to reduce the power consumption.
+
+properties:
+  compatible:
+    enum:
+      - mediatek,mt8183-cci
+      - mediatek,mt8186-cci
+
+  clocks:
+    items:
+      - description:
+          The multiplexer for clock input of the bus.
+      - description:
+          A parent of "bus" clock which is used as an intermediate clock source
+          when the original clock source (PLL) is under transition and not
+          stable yet.
+
+  clock-names:
+    items:
+      - const: cci
+      - const: intermediate
+
+  operating-points-v2: true
+  opp-table: true
+
+  proc-supply:
+    description:
+      Phandle of the regulator for CCI that provides the supply voltage.
+
+  sram-supply:
+    description:
+      Phandle of the regulator for sram of CCI that provides the supply
+      voltage. When it is present, the implementation needs to do
+      "voltage tracking" to step by step scale up/down Vproc and Vsram to fit
+      SoC specific needs. When absent, the voltage scaling flow is handled by
+      hardware, hence no software "voltage tracking" is needed.
+
+required:
+  - compatible
+  - clocks
+  - clock-names
+  - operating-points-v2
+  - proc-supply
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/mt8183-clk.h>
+    cci: cci {
+        compatible = "mediatek,mt8183-cci";
+        clocks = <&mcucfg CLK_MCU_BUS_SEL>,
+                 <&topckgen CLK_TOP_ARMPLL_DIV_PLL1>;
+        clock-names = "cci", "intermediate";
+        operating-points-v2 = <&cci_opp>;
+        proc-supply = <&mt6358_vproc12_reg>;
+    };
+
+    cci_opp: opp-table-cci {
+        compatible = "operating-points-v2";
+        opp-shared;
+        opp2_00: opp-273000000 {
+            opp-hz = /bits/ 64 <273000000>;
+            opp-microvolt = <650000>;
+        };
+        opp2_01: opp-338000000 {
+            opp-hz = /bits/ 64 <338000000>;
+            opp-microvolt = <687500>;
+        };
+        opp2_02: opp-403000000 {
+            opp-hz = /bits/ 64 <403000000>;
+            opp-microvolt = <718750>;
+        };
+        opp2_03: opp-463000000 {
+            opp-hz = /bits/ 64 <463000000>;
+            opp-microvolt = <756250>;
+        };
+        opp2_04: opp-546000000 {
+            opp-hz = /bits/ 64 <546000000>;
+            opp-microvolt = <800000>;
+        };
+        opp2_05: opp-624000000 {
+            opp-hz = /bits/ 64 <624000000>;
+            opp-microvolt = <818750>;
+        };
+        opp2_06: opp-689000000 {
+            opp-hz = /bits/ 64 <689000000>;
+            opp-microvolt = <850000>;
+        };
+        opp2_07: opp-767000000 {
+            opp-hz = /bits/ 64 <767000000>;
+            opp-microvolt = <868750>;
+        };
+        opp2_08: opp-845000000 {
+            opp-hz = /bits/ 64 <845000000>;
+            opp-microvolt = <893750>;
+        };
+        opp2_09: opp-871000000 {
+            opp-hz = /bits/ 64 <871000000>;
+            opp-microvolt = <906250>;
+        };
+        opp2_10: opp-923000000 {
+            opp-hz = /bits/ 64 <923000000>;
+            opp-microvolt = <931250>;
+        };
+        opp2_11: opp-962000000 {
+            opp-hz = /bits/ 64 <962000000>;
+            opp-microvolt = <943750>;
+        };
+        opp2_12: opp-1027000000 {
+            opp-hz = /bits/ 64 <1027000000>;
+            opp-microvolt = <975000>;
+        };
+        opp2_13: opp-1092000000 {
+            opp-hz = /bits/ 64 <1092000000>;
+            opp-microvolt = <1000000>;
+        };
+        opp2_14: opp-1144000000 {
+            opp-hz = /bits/ 64 <1144000000>;
+            opp-microvolt = <1025000>;
+        };
+        opp2_15: opp-1196000000 {
+            opp-hz = /bits/ 64 <1196000000>;
+            opp-microvolt = <1050000>;
+        };
+    };
diff --git a/MAINTAINERS b/MAINTAINERS
index b54288db77aa..2800ddceb54c 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -5757,6 +5757,7 @@ L:	linux-pm@vger.kernel.org
 S:	Maintained
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/linux.git
 F:	Documentation/devicetree/bindings/devfreq/
+F:	Documentation/devicetree/bindings/interconnect/mediatek,cci.yaml
 F:	drivers/devfreq/
 F:	include/linux/devfreq.h
 F:	include/trace/events/devfreq.h
-- 
2.18.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v7 1/2] dt-bindings: interconnect: Add MediaTek CCI dt-bindings

[Johnson Wang]

Add devicetree binding of MediaTek CCI on MT8183 and MT8186.

Signed-off-by: Jia-Wei Chang <jia-wei.chang@mediatek.com>
Signed-off-by: Johnson Wang <johnson.wang@mediatek.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Georgi Djakov <djakov@kernel.org>
---
 .../bindings/interconnect/mediatek,cci.yaml   | 141 ++++++++++++++++++
 MAINTAINERS                                   |   1 +
 2 files changed, 142 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/interconnect/mediatek,cci.yaml

diff --git a/Documentation/devicetree/bindings/interconnect/mediatek,cci.yaml b/Documentation/devicetree/bindings/interconnect/mediatek,cci.yaml
new file mode 100644
index 000000000000..449c7c988229
--- /dev/null
+++ b/Documentation/devicetree/bindings/interconnect/mediatek,cci.yaml
@@ -0,0 +1,141 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/interconnect/mediatek,cci.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek Cache Coherent Interconnect (CCI) frequency and voltage scaling
+
+maintainers:
+  - Jia-Wei Chang <jia-wei.chang@mediatek.com>
+  - Johnson Wang <johnson.wang@mediatek.com>
+
+description: |
+  MediaTek Cache Coherent Interconnect (CCI) is a hardware engine used by
+  MT8183 and MT8186 SoCs to scale the frequency and adjust the voltage in
+  hardware. It can also optimize the voltage to reduce the power consumption.
+
+properties:
+  compatible:
+    enum:
+      - mediatek,mt8183-cci
+      - mediatek,mt8186-cci
+
+  clocks:
+    items:
+      - description:
+          The multiplexer for clock input of the bus.
+      - description:
+          A parent of "bus" clock which is used as an intermediate clock source
+          when the original clock source (PLL) is under transition and not
+          stable yet.
+
+  clock-names:
+    items:
+      - const: cci
+      - const: intermediate
+
+  operating-points-v2: true
+  opp-table: true
+
+  proc-supply:
+    description:
+      Phandle of the regulator for CCI that provides the supply voltage.
+
+  sram-supply:
+    description:
+      Phandle of the regulator for sram of CCI that provides the supply
+      voltage. When it is present, the implementation needs to do
+      "voltage tracking" to step by step scale up/down Vproc and Vsram to fit
+      SoC specific needs. When absent, the voltage scaling flow is handled by
+      hardware, hence no software "voltage tracking" is needed.
+
+required:
+  - compatible
+  - clocks
+  - clock-names
+  - operating-points-v2
+  - proc-supply
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/clock/mt8183-clk.h>
+    cci: cci {
+        compatible = "mediatek,mt8183-cci";
+        clocks = <&mcucfg CLK_MCU_BUS_SEL>,
+                 <&topckgen CLK_TOP_ARMPLL_DIV_PLL1>;
+        clock-names = "cci", "intermediate";
+        operating-points-v2 = <&cci_opp>;
+        proc-supply = <&mt6358_vproc12_reg>;
+    };
+
+    cci_opp: opp-table-cci {
+        compatible = "operating-points-v2";
+        opp-shared;
+        opp2_00: opp-273000000 {
+            opp-hz = /bits/ 64 <273000000>;
+            opp-microvolt = <650000>;
+        };
+        opp2_01: opp-338000000 {
+            opp-hz = /bits/ 64 <338000000>;
+            opp-microvolt = <687500>;
+        };
+        opp2_02: opp-403000000 {
+            opp-hz = /bits/ 64 <403000000>;
+            opp-microvolt = <718750>;
+        };
+        opp2_03: opp-463000000 {
+            opp-hz = /bits/ 64 <463000000>;
+            opp-microvolt = <756250>;
+        };
+        opp2_04: opp-546000000 {
+            opp-hz = /bits/ 64 <546000000>;
+            opp-microvolt = <800000>;
+        };
+        opp2_05: opp-624000000 {
+            opp-hz = /bits/ 64 <624000000>;
+            opp-microvolt = <818750>;
+        };
+        opp2_06: opp-689000000 {
+            opp-hz = /bits/ 64 <689000000>;
+            opp-microvolt = <850000>;
+        };
+        opp2_07: opp-767000000 {
+            opp-hz = /bits/ 64 <767000000>;
+            opp-microvolt = <868750>;
+        };
+        opp2_08: opp-845000000 {
+            opp-hz = /bits/ 64 <845000000>;
+            opp-microvolt = <893750>;
+        };
+        opp2_09: opp-871000000 {
+            opp-hz = /bits/ 64 <871000000>;
+            opp-microvolt = <906250>;
+        };
+        opp2_10: opp-923000000 {
+            opp-hz = /bits/ 64 <923000000>;
+            opp-microvolt = <931250>;
+        };
+        opp2_11: opp-962000000 {
+            opp-hz = /bits/ 64 <962000000>;
+            opp-microvolt = <943750>;
+        };
+        opp2_12: opp-1027000000 {
+            opp-hz = /bits/ 64 <1027000000>;
+            opp-microvolt = <975000>;
+        };
+        opp2_13: opp-1092000000 {
+            opp-hz = /bits/ 64 <1092000000>;
+            opp-microvolt = <1000000>;
+        };
+        opp2_14: opp-1144000000 {
+            opp-hz = /bits/ 64 <1144000000>;
+            opp-microvolt = <1025000>;
+        };
+        opp2_15: opp-1196000000 {
+            opp-hz = /bits/ 64 <1196000000>;
+            opp-microvolt = <1050000>;
+        };
+    };
diff --git a/MAINTAINERS b/MAINTAINERS
index b54288db77aa..2800ddceb54c 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -5757,6 +5757,7 @@ L:	linux-pm@vger.kernel.org
 S:	Maintained
 T:	git git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/linux.git
 F:	Documentation/devicetree/bindings/devfreq/
+F:	Documentation/devicetree/bindings/interconnect/mediatek,cci.yaml
 F:	drivers/devfreq/
 F:	include/linux/devfreq.h
 F:	include/trace/events/devfreq.h
-- 
2.18.0

Re: [PATCH v7 1/2] dt-bindings: interconnect: Add MediaTek CCI dt-bindings

[AngeloGioacchino Del Regno]

Il 07/06/22 16:05, Johnson Wang ha scritto:
> Add devicetree binding of MediaTek CCI on MT8183 and MT8186.
> 
> Signed-off-by: Jia-Wei Chang <jia-wei.chang@mediatek.com>
> Signed-off-by: Johnson Wang <johnson.wang@mediatek.com>
> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
> Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
> Acked-by: Georgi Djakov <djakov@kernel.org>
> ---
>   .../bindings/interconnect/mediatek,cci.yaml   | 141 ++++++++++++++++++

Uhm, I've just noticed that this is being put in the bindings/interconnect folder.
The mediatek,cci is *not* an interconnect driver, but a devfreq one and is not
using any ICC APIs.

Shouldn't this go to bindings/devfreq/ instead?!

>   MAINTAINERS                                   |   1 +
>   2 files changed, 142 insertions(+)
>   create mode 100644 Documentation/devicetree/bindings/interconnect/mediatek,cci.yaml
> 

_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

Re: [PATCH v7 1/2] dt-bindings: interconnect: Add MediaTek CCI dt-bindings

[AngeloGioacchino Del Regno]

Il 07/06/22 16:05, Johnson Wang ha scritto:
> Add devicetree binding of MediaTek CCI on MT8183 and MT8186.
> 
> Signed-off-by: Jia-Wei Chang <jia-wei.chang@mediatek.com>
> Signed-off-by: Johnson Wang <johnson.wang@mediatek.com>
> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
> Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
> Acked-by: Georgi Djakov <djakov@kernel.org>
> ---
>   .../bindings/interconnect/mediatek,cci.yaml   | 141 ++++++++++++++++++

Uhm, I've just noticed that this is being put in the bindings/interconnect folder.
The mediatek,cci is *not* an interconnect driver, but a devfreq one and is not
using any ICC APIs.

Shouldn't this go to bindings/devfreq/ instead?!

>   MAINTAINERS                                   |   1 +
>   2 files changed, 142 insertions(+)
>   create mode 100644 Documentation/devicetree/bindings/interconnect/mediatek,cci.yaml
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v7 1/2] dt-bindings: interconnect: Add MediaTek CCI dt-bindings

[AngeloGioacchino Del Regno]

Il 07/06/22 16:05, Johnson Wang ha scritto:
> Add devicetree binding of MediaTek CCI on MT8183 and MT8186.
> 
> Signed-off-by: Jia-Wei Chang <jia-wei.chang@mediatek.com>
> Signed-off-by: Johnson Wang <johnson.wang@mediatek.com>
> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
> Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
> Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
> Acked-by: Georgi Djakov <djakov@kernel.org>
> ---
>   .../bindings/interconnect/mediatek,cci.yaml   | 141 ++++++++++++++++++

Uhm, I've just noticed that this is being put in the bindings/interconnect folder.
The mediatek,cci is *not* an interconnect driver, but a devfreq one and is not
using any ICC APIs.

Shouldn't this go to bindings/devfreq/ instead?!

>   MAINTAINERS                                   |   1 +
>   2 files changed, 142 insertions(+)
>   create mode 100644 Documentation/devicetree/bindings/interconnect/mediatek,cci.yaml
> 

Re: [PATCH v7 1/2] dt-bindings: interconnect: Add MediaTek CCI dt-bindings

[Krzysztof Kozlowski]

On 10/06/2022 12:43, AngeloGioacchino Del Regno wrote:
> Il 07/06/22 16:05, Johnson Wang ha scritto:
>> Add devicetree binding of MediaTek CCI on MT8183 and MT8186.
>>
>> Signed-off-by: Jia-Wei Chang <jia-wei.chang@mediatek.com>
>> Signed-off-by: Johnson Wang <johnson.wang@mediatek.com>
>> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
>> Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
>> Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
>> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
>> Acked-by: Georgi Djakov <djakov@kernel.org>
>> ---
>>   .../bindings/interconnect/mediatek,cci.yaml   | 141 ++++++++++++++++++
> 
> Uhm, I've just noticed that this is being put in the bindings/interconnect folder.
> The mediatek,cci is *not* an interconnect driver, but a devfreq one and is not
> using any ICC APIs.
> 
> Shouldn't this go to bindings/devfreq/ instead?!

No, devfreq is not a hardware subsystem.

Best regards,
Krzysztof

Re: [PATCH v7 1/2] dt-bindings: interconnect: Add MediaTek CCI dt-bindings

[Krzysztof Kozlowski]

On 10/06/2022 12:43, AngeloGioacchino Del Regno wrote:
> Il 07/06/22 16:05, Johnson Wang ha scritto:
>> Add devicetree binding of MediaTek CCI on MT8183 and MT8186.
>>
>> Signed-off-by: Jia-Wei Chang <jia-wei.chang@mediatek.com>
>> Signed-off-by: Johnson Wang <johnson.wang@mediatek.com>
>> Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
>> Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
>> Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
>> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
>> Acked-by: Georgi Djakov <djakov@kernel.org>
>> ---
>>   .../bindings/interconnect/mediatek,cci.yaml   | 141 ++++++++++++++++++
> 
> Uhm, I've just noticed that this is being put in the bindings/interconnect folder.
> The mediatek,cci is *not* an interconnect driver, but a devfreq one and is not
> using any ICC APIs.
> 
> Shouldn't this go to bindings/devfreq/ instead?!

No, devfreq is not a hardware subsystem.

Best regards,
Krzysztof

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v7 2/2] PM / devfreq: mediatek: Introduce MediaTek CCI devfreq driver

[Johnson Wang]

We introduce a devfreq driver for the MediaTek Cache Coherent Interconnect
(CCI) used by some MediaTek SoCs.

In this driver, we use the passive devfreq driver to get target frequencies
and adjust voltages accordingly. In MT8183 and MT8186, the MediaTek CCI
is supplied by the same regulators with the little core CPUs.

Signed-off-by: Jia-Wei Chang <jia-wei.chang@mediatek.com>
Signed-off-by: Johnson Wang <johnson.wang@mediatek.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
---
 drivers/devfreq/Kconfig           |  10 +
 drivers/devfreq/Makefile          |   1 +
 drivers/devfreq/mtk-cci-devfreq.c | 440 ++++++++++++++++++++++++++++++
 3 files changed, 451 insertions(+)
 create mode 100644 drivers/devfreq/mtk-cci-devfreq.c

diff --git a/drivers/devfreq/Kconfig b/drivers/devfreq/Kconfig
index 87eb2b837e68..9754d8b31621 100644
--- a/drivers/devfreq/Kconfig
+++ b/drivers/devfreq/Kconfig
@@ -120,6 +120,16 @@ config ARM_TEGRA_DEVFREQ
 	  It reads ACTMON counters of memory controllers and adjusts the
 	  operating frequencies and voltages with OPP support.
 
+config ARM_MEDIATEK_CCI_DEVFREQ
+	tristate "MEDIATEK CCI DEVFREQ Driver"
+	depends on ARM_MEDIATEK_CPUFREQ || COMPILE_TEST
+	select DEVFREQ_GOV_PASSIVE
+	help
+	  This adds a devfreq driver for MediaTek Cache Coherent Interconnect
+	  which is shared the same regulators with the cpu cluster. It can track
+	  buck voltages and update a proper CCI frequency. Use the notification
+	  to get the regulator status.
+
 config ARM_RK3399_DMC_DEVFREQ
 	tristate "ARM RK3399 DMC DEVFREQ Driver"
 	depends on (ARCH_ROCKCHIP && HAVE_ARM_SMCCC) || \
diff --git a/drivers/devfreq/Makefile b/drivers/devfreq/Makefile
index 0b6be92a25d9..bf40d04928d0 100644
--- a/drivers/devfreq/Makefile
+++ b/drivers/devfreq/Makefile
@@ -11,6 +11,7 @@ obj-$(CONFIG_DEVFREQ_GOV_PASSIVE)	+= governor_passive.o
 obj-$(CONFIG_ARM_EXYNOS_BUS_DEVFREQ)	+= exynos-bus.o
 obj-$(CONFIG_ARM_IMX_BUS_DEVFREQ)	+= imx-bus.o
 obj-$(CONFIG_ARM_IMX8M_DDRC_DEVFREQ)	+= imx8m-ddrc.o
+obj-$(CONFIG_ARM_MEDIATEK_CCI_DEVFREQ)	+= mtk-cci-devfreq.o
 obj-$(CONFIG_ARM_RK3399_DMC_DEVFREQ)	+= rk3399_dmc.o
 obj-$(CONFIG_ARM_SUN8I_A33_MBUS_DEVFREQ)	+= sun8i-a33-mbus.o
 obj-$(CONFIG_ARM_TEGRA_DEVFREQ)		+= tegra30-devfreq.o
diff --git a/drivers/devfreq/mtk-cci-devfreq.c b/drivers/devfreq/mtk-cci-devfreq.c
new file mode 100644
index 000000000000..71abb3fbd042
--- /dev/null
+++ b/drivers/devfreq/mtk-cci-devfreq.c
@@ -0,0 +1,440 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2022 MediaTek Inc.
+ */
+
+#include <linux/clk.h>
+#include <linux/devfreq.h>
+#include <linux/minmax.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/pm_opp.h>
+#include <linux/regulator/consumer.h>
+
+struct mtk_ccifreq_platform_data {
+	int min_volt_shift;
+	int max_volt_shift;
+	int proc_max_volt;
+	int sram_min_volt;
+	int sram_max_volt;
+};
+
+struct mtk_ccifreq_drv {
+	struct device *dev;
+	struct devfreq *devfreq;
+	struct regulator *proc_reg;
+	struct regulator *sram_reg;
+	struct clk *cci_clk;
+	struct clk *inter_clk;
+	int inter_voltage;
+	unsigned long pre_freq;
+	/* Avoid race condition for regulators between notify and policy */
+	struct mutex reg_lock;
+	struct notifier_block opp_nb;
+	const struct mtk_ccifreq_platform_data *soc_data;
+	int vtrack_max;
+};
+
+static int mtk_ccifreq_set_voltage(struct mtk_ccifreq_drv *drv, int new_voltage)
+{
+	const struct mtk_ccifreq_platform_data *soc_data = drv->soc_data;
+	struct device *dev = drv->dev;
+	int pre_voltage, pre_vsram, new_vsram, vsram, voltage, ret;
+	int retry_max = drv->vtrack_max;
+
+	if (!drv->sram_reg) {
+		ret = regulator_set_voltage(drv->proc_reg, new_voltage,
+					    drv->soc_data->proc_max_volt);
+		return ret;
+	}
+
+	pre_voltage = regulator_get_voltage(drv->proc_reg);
+	if (pre_voltage < 0) {
+		dev_err(dev, "invalid vproc value: %d\n", pre_voltage);
+		return pre_voltage;
+	}
+
+	pre_vsram = regulator_get_voltage(drv->sram_reg);
+	if (pre_vsram < 0) {
+		dev_err(dev, "invalid vsram value: %d\n", pre_vsram);
+		return pre_vsram;
+	}
+
+	new_vsram = clamp(new_voltage + soc_data->min_volt_shift,
+			  soc_data->sram_min_volt, soc_data->sram_max_volt);
+
+	do {
+		if (pre_voltage <= new_voltage) {
+			vsram = clamp(pre_voltage + soc_data->max_volt_shift,
+				      soc_data->sram_min_volt, new_vsram);
+			ret = regulator_set_voltage(drv->sram_reg, vsram,
+						    soc_data->sram_max_volt);
+			if (ret)
+				return ret;
+
+			if (vsram == soc_data->sram_max_volt ||
+			    new_vsram == soc_data->sram_min_volt)
+				voltage = new_voltage;
+			else
+				voltage = vsram - soc_data->min_volt_shift;
+
+			ret = regulator_set_voltage(drv->proc_reg, voltage,
+						    soc_data->proc_max_volt);
+			if (ret) {
+				regulator_set_voltage(drv->sram_reg, pre_vsram,
+						      soc_data->sram_max_volt);
+				return ret;
+			}
+		} else if (pre_voltage > new_voltage) {
+			voltage = max(new_voltage,
+				      pre_vsram - soc_data->max_volt_shift);
+			ret = regulator_set_voltage(drv->proc_reg, voltage,
+						    soc_data->proc_max_volt);
+			if (ret)
+				return ret;
+
+			if (voltage == new_voltage)
+				vsram = new_vsram;
+			else
+				vsram = max(new_vsram,
+					    voltage + soc_data->min_volt_shift);
+
+			ret = regulator_set_voltage(drv->sram_reg, vsram,
+						    soc_data->sram_max_volt);
+			if (ret) {
+				regulator_set_voltage(drv->proc_reg, pre_voltage,
+						      soc_data->proc_max_volt);
+				return ret;
+			}
+		}
+
+		pre_voltage = voltage;
+		pre_vsram = vsram;
+
+		if (--retry_max < 0) {
+			dev_err(dev,
+				"over loop count, failed to set voltage\n");
+			return -EINVAL;
+		}
+	} while (voltage != new_voltage || vsram != new_vsram);
+
+	return 0;
+}
+
+static int mtk_ccifreq_target(struct device *dev, unsigned long *freq,
+			      u32 flags)
+{
+	struct mtk_ccifreq_drv *drv = dev_get_drvdata(dev);
+	struct clk *cci_pll = clk_get_parent(drv->cci_clk);
+	struct dev_pm_opp *opp;
+	unsigned long opp_rate;
+	int voltage, pre_voltage, inter_voltage, target_voltage, ret;
+
+	if (!drv)
+		return -EINVAL;
+
+	if (drv->pre_freq == *freq)
+		return 0;
+
+	inter_voltage = drv->inter_voltage;
+
+	opp_rate = *freq;
+	opp = devfreq_recommended_opp(dev, &opp_rate, 1);
+	if (IS_ERR(opp)) {
+		dev_err(dev, "failed to find opp for freq: %ld\n", opp_rate);
+		return PTR_ERR(opp);
+	}
+
+	mutex_lock(&drv->reg_lock);
+
+	voltage = dev_pm_opp_get_voltage(opp);
+	dev_pm_opp_put(opp);
+
+	pre_voltage = regulator_get_voltage(drv->proc_reg);
+	if (pre_voltage < 0) {
+		dev_err(dev, "invalid vproc value: %d\n", pre_voltage);
+		ret = pre_voltage;
+		goto out_unlock;
+	}
+
+	/* scale up: set voltage first then freq. */
+	target_voltage = max(inter_voltage, voltage);
+	if (pre_voltage <= target_voltage) {
+		ret = mtk_ccifreq_set_voltage(drv, target_voltage);
+		if (ret) {
+			dev_err(dev, "failed to scale up voltage\n");
+			goto out_restore_voltage;
+		}
+	}
+
+	/* switch the cci clock to intermediate clock source. */
+	ret = clk_set_parent(drv->cci_clk, drv->inter_clk);
+	if (ret) {
+		dev_err(dev, "failed to re-parent cci clock\n");
+		goto out_restore_voltage;
+	}
+
+	/* set the original clock to target rate. */
+	ret = clk_set_rate(cci_pll, *freq);
+	if (ret) {
+		dev_err(dev, "failed to set cci pll rate: %d\n", ret);
+		clk_set_parent(drv->cci_clk, cci_pll);
+		goto out_restore_voltage;
+	}
+
+	/* switch the cci clock back to the original clock source. */
+	ret = clk_set_parent(drv->cci_clk, cci_pll);
+	if (ret) {
+		dev_err(dev, "failed to re-parent cci clock\n");
+		mtk_ccifreq_set_voltage(drv, inter_voltage);
+		goto out_unlock;
+	}
+
+	/*
+	 * If the new voltage is lower than the intermediate voltage or the
+	 * original voltage, scale down to the new voltage.
+	 */
+	if (voltage < inter_voltage || voltage < pre_voltage) {
+		ret = mtk_ccifreq_set_voltage(drv, voltage);
+		if (ret) {
+			dev_err(dev, "failed to scale down voltage\n");
+			goto out_unlock;
+		}
+	}
+
+	drv->pre_freq = *freq;
+	mutex_unlock(&drv->reg_lock);
+
+	return 0;
+
+out_restore_voltage:
+	mtk_ccifreq_set_voltage(drv, pre_voltage);
+
+out_unlock:
+	mutex_unlock(&drv->reg_lock);
+	return ret;
+}
+
+static int mtk_ccifreq_opp_notifier(struct notifier_block *nb,
+				    unsigned long event, void *data)
+{
+	struct dev_pm_opp *opp = data;
+	struct mtk_ccifreq_drv *drv;
+	unsigned long freq, volt;
+
+	drv = container_of(nb, struct mtk_ccifreq_drv, opp_nb);
+
+	if (event == OPP_EVENT_ADJUST_VOLTAGE) {
+		freq = dev_pm_opp_get_freq(opp);
+
+		mutex_lock(&drv->reg_lock);
+		/* current opp item is changed */
+		if (freq == drv->pre_freq) {
+			volt = dev_pm_opp_get_voltage(opp);
+			mtk_ccifreq_set_voltage(drv, volt);
+		}
+		mutex_unlock(&drv->reg_lock);
+	}
+
+	return 0;
+}
+
+static struct devfreq_dev_profile mtk_ccifreq_profile = {
+	.target = mtk_ccifreq_target,
+};
+
+static int mtk_ccifreq_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct mtk_ccifreq_drv *drv;
+	struct devfreq_passive_data *passive_data;
+	struct dev_pm_opp *opp;
+	unsigned long rate, opp_volt;
+	int ret;
+
+	drv = devm_kzalloc(dev, sizeof(*drv), GFP_KERNEL);
+	if (!drv)
+		return -ENOMEM;
+
+	drv->dev = dev;
+	drv->soc_data = (const struct mtk_ccifreq_platform_data *)
+				of_device_get_match_data(&pdev->dev);
+	mutex_init(&drv->reg_lock);
+	platform_set_drvdata(pdev, drv);
+
+	drv->cci_clk = devm_clk_get(dev, "cci");
+	if (IS_ERR(drv->cci_clk)) {
+		ret = PTR_ERR(drv->cci_clk);
+		return dev_err_probe(dev, ret, "failed to get cci clk\n");
+	}
+
+	drv->inter_clk = devm_clk_get(dev, "intermediate");
+	if (IS_ERR(drv->inter_clk)) {
+		ret = PTR_ERR(drv->inter_clk);
+		return dev_err_probe(dev, ret,
+				     "failed to get intermediate clk\n");
+	}
+
+	drv->proc_reg = devm_regulator_get_optional(dev, "proc");
+	if (IS_ERR(drv->proc_reg)) {
+		ret = PTR_ERR(drv->proc_reg);
+		return dev_err_probe(dev, ret,
+				     "failed to get proc regulator\n");
+	}
+
+	ret = regulator_enable(drv->proc_reg);
+	if (ret) {
+		dev_err(dev, "failed to enable proc regulator\n");
+		return ret;
+	}
+
+	drv->sram_reg = devm_regulator_get_optional(dev, "sram");
+	if (IS_ERR(drv->sram_reg))
+		drv->sram_reg = NULL;
+	else {
+		ret = regulator_enable(drv->sram_reg);
+		if (ret) {
+			dev_err(dev, "failed to enable sram regulator\n");
+			goto out_free_resources;
+		}
+	}
+
+	/*
+	 * We assume min voltage is 0 and tracking target voltage using
+	 * min_volt_shift for each iteration.
+	 * The retry_max is 3 times of expected iteration count.
+	 */
+	drv->vtrack_max = 3 * DIV_ROUND_UP(max(drv->soc_data->sram_max_volt,
+					       drv->soc_data->proc_max_volt),
+					   drv->soc_data->min_volt_shift);
+
+	ret = clk_prepare_enable(drv->cci_clk);
+	if (ret)
+		goto out_free_resources;
+
+	ret = dev_pm_opp_of_add_table(dev);
+	if (ret) {
+		dev_err(dev, "failed to add opp table: %d\n", ret);
+		goto out_disable_cci_clk;
+	}
+
+	rate = clk_get_rate(drv->inter_clk);
+	opp = dev_pm_opp_find_freq_ceil(dev, &rate);
+	if (IS_ERR(opp)) {
+		ret = PTR_ERR(opp);
+		dev_err(dev, "failed to get intermediate opp: %d\n", ret);
+		goto out_remove_opp_table;
+	}
+	drv->inter_voltage = dev_pm_opp_get_voltage(opp);
+	dev_pm_opp_put(opp);
+
+	rate = U32_MAX;
+	opp = dev_pm_opp_find_freq_floor(drv->dev, &rate);
+	if (IS_ERR(opp)) {
+		dev_err(dev, "failed to get opp\n");
+		ret = PTR_ERR(opp);
+		goto out_remove_opp_table;
+	}
+
+	opp_volt = dev_pm_opp_get_voltage(opp);
+	dev_pm_opp_put(opp);
+	ret = mtk_ccifreq_set_voltage(drv, opp_volt);
+	if (ret) {
+		dev_err(dev, "failed to scale to highest voltage %lu in proc_reg\n",
+			opp_volt);
+		goto out_remove_opp_table;
+	}
+
+	passive_data = devm_kzalloc(dev, sizeof(*passive_data), GFP_KERNEL);
+	if (!passive_data) {
+		ret = -ENOMEM;
+		goto out_remove_opp_table;
+	}
+
+	passive_data->parent_type = CPUFREQ_PARENT_DEV;
+	drv->devfreq = devm_devfreq_add_device(dev, &mtk_ccifreq_profile,
+					       DEVFREQ_GOV_PASSIVE,
+					       passive_data);
+	if (IS_ERR(drv->devfreq)) {
+		ret = -EPROBE_DEFER;
+		dev_err(dev, "failed to add devfreq device: %ld\n",
+			PTR_ERR(drv->devfreq));
+		goto out_remove_opp_table;
+	}
+
+	drv->opp_nb.notifier_call = mtk_ccifreq_opp_notifier;
+	ret = dev_pm_opp_register_notifier(dev, &drv->opp_nb);
+	if (ret) {
+		dev_err(dev, "failed to register opp notifier: %d\n", ret);
+		goto out_remove_opp_table;
+	}
+	return 0;
+
+out_remove_opp_table:
+	dev_pm_opp_of_remove_table(dev);
+
+out_disable_cci_clk:
+	clk_disable_unprepare(drv->cci_clk);
+
+out_free_resources:
+	if (regulator_is_enabled(drv->proc_reg))
+		regulator_disable(drv->proc_reg);
+	if (drv->sram_reg && regulator_is_enabled(drv->sram_reg))
+		regulator_disable(drv->sram_reg);
+
+	return ret;
+}
+
+static int mtk_ccifreq_remove(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct mtk_ccifreq_drv *drv;
+
+	drv = platform_get_drvdata(pdev);
+
+	dev_pm_opp_unregister_notifier(dev, &drv->opp_nb);
+	dev_pm_opp_of_remove_table(dev);
+	clk_disable_unprepare(drv->cci_clk);
+	regulator_disable(drv->proc_reg);
+	if (drv->sram_reg)
+		regulator_disable(drv->sram_reg);
+
+	return 0;
+}
+
+static const struct mtk_ccifreq_platform_data mt8183_platform_data = {
+	.min_volt_shift = 100000,
+	.max_volt_shift = 200000,
+	.proc_max_volt = 1150000,
+};
+
+static const struct mtk_ccifreq_platform_data mt8186_platform_data = {
+	.min_volt_shift = 100000,
+	.max_volt_shift = 250000,
+	.proc_max_volt = 1118750,
+	.sram_min_volt = 850000,
+	.sram_max_volt = 1118750,
+};
+
+static const struct of_device_id mtk_ccifreq_machines[] = {
+	{ .compatible = "mediatek,mt8183-cci", .data = &mt8183_platform_data },
+	{ .compatible = "mediatek,mt8186-cci", .data = &mt8186_platform_data },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, mtk_ccifreq_machines);
+
+static struct platform_driver mtk_ccifreq_platdrv = {
+	.probe	= mtk_ccifreq_probe,
+	.remove	= mtk_ccifreq_remove,
+	.driver = {
+		.name = "mtk-ccifreq",
+		.of_match_table = mtk_ccifreq_machines,
+	},
+};
+module_platform_driver(mtk_ccifreq_platdrv);
+
+MODULE_DESCRIPTION("MediaTek CCI devfreq driver");
+MODULE_AUTHOR("Jia-Wei Chang <jia-wei.chang@mediatek.com>");
+MODULE_LICENSE("GPL v2");
-- 
2.18.0


_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

[PATCH v7 2/2] PM / devfreq: mediatek: Introduce MediaTek CCI devfreq driver

[Johnson Wang]

We introduce a devfreq driver for the MediaTek Cache Coherent Interconnect
(CCI) used by some MediaTek SoCs.

In this driver, we use the passive devfreq driver to get target frequencies
and adjust voltages accordingly. In MT8183 and MT8186, the MediaTek CCI
is supplied by the same regulators with the little core CPUs.

Signed-off-by: Jia-Wei Chang <jia-wei.chang@mediatek.com>
Signed-off-by: Johnson Wang <johnson.wang@mediatek.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
---
 drivers/devfreq/Kconfig           |  10 +
 drivers/devfreq/Makefile          |   1 +
 drivers/devfreq/mtk-cci-devfreq.c | 440 ++++++++++++++++++++++++++++++
 3 files changed, 451 insertions(+)
 create mode 100644 drivers/devfreq/mtk-cci-devfreq.c

diff --git a/drivers/devfreq/Kconfig b/drivers/devfreq/Kconfig
index 87eb2b837e68..9754d8b31621 100644
--- a/drivers/devfreq/Kconfig
+++ b/drivers/devfreq/Kconfig
@@ -120,6 +120,16 @@ config ARM_TEGRA_DEVFREQ
 	  It reads ACTMON counters of memory controllers and adjusts the
 	  operating frequencies and voltages with OPP support.
 
+config ARM_MEDIATEK_CCI_DEVFREQ
+	tristate "MEDIATEK CCI DEVFREQ Driver"
+	depends on ARM_MEDIATEK_CPUFREQ || COMPILE_TEST
+	select DEVFREQ_GOV_PASSIVE
+	help
+	  This adds a devfreq driver for MediaTek Cache Coherent Interconnect
+	  which is shared the same regulators with the cpu cluster. It can track
+	  buck voltages and update a proper CCI frequency. Use the notification
+	  to get the regulator status.
+
 config ARM_RK3399_DMC_DEVFREQ
 	tristate "ARM RK3399 DMC DEVFREQ Driver"
 	depends on (ARCH_ROCKCHIP && HAVE_ARM_SMCCC) || \
diff --git a/drivers/devfreq/Makefile b/drivers/devfreq/Makefile
index 0b6be92a25d9..bf40d04928d0 100644
--- a/drivers/devfreq/Makefile
+++ b/drivers/devfreq/Makefile
@@ -11,6 +11,7 @@ obj-$(CONFIG_DEVFREQ_GOV_PASSIVE)	+= governor_passive.o
 obj-$(CONFIG_ARM_EXYNOS_BUS_DEVFREQ)	+= exynos-bus.o
 obj-$(CONFIG_ARM_IMX_BUS_DEVFREQ)	+= imx-bus.o
 obj-$(CONFIG_ARM_IMX8M_DDRC_DEVFREQ)	+= imx8m-ddrc.o
+obj-$(CONFIG_ARM_MEDIATEK_CCI_DEVFREQ)	+= mtk-cci-devfreq.o
 obj-$(CONFIG_ARM_RK3399_DMC_DEVFREQ)	+= rk3399_dmc.o
 obj-$(CONFIG_ARM_SUN8I_A33_MBUS_DEVFREQ)	+= sun8i-a33-mbus.o
 obj-$(CONFIG_ARM_TEGRA_DEVFREQ)		+= tegra30-devfreq.o
diff --git a/drivers/devfreq/mtk-cci-devfreq.c b/drivers/devfreq/mtk-cci-devfreq.c
new file mode 100644
index 000000000000..71abb3fbd042
--- /dev/null
+++ b/drivers/devfreq/mtk-cci-devfreq.c
@@ -0,0 +1,440 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2022 MediaTek Inc.
+ */
+
+#include <linux/clk.h>
+#include <linux/devfreq.h>
+#include <linux/minmax.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/pm_opp.h>
+#include <linux/regulator/consumer.h>
+
+struct mtk_ccifreq_platform_data {
+	int min_volt_shift;
+	int max_volt_shift;
+	int proc_max_volt;
+	int sram_min_volt;
+	int sram_max_volt;
+};
+
+struct mtk_ccifreq_drv {
+	struct device *dev;
+	struct devfreq *devfreq;
+	struct regulator *proc_reg;
+	struct regulator *sram_reg;
+	struct clk *cci_clk;
+	struct clk *inter_clk;
+	int inter_voltage;
+	unsigned long pre_freq;
+	/* Avoid race condition for regulators between notify and policy */
+	struct mutex reg_lock;
+	struct notifier_block opp_nb;
+	const struct mtk_ccifreq_platform_data *soc_data;
+	int vtrack_max;
+};
+
+static int mtk_ccifreq_set_voltage(struct mtk_ccifreq_drv *drv, int new_voltage)
+{
+	const struct mtk_ccifreq_platform_data *soc_data = drv->soc_data;
+	struct device *dev = drv->dev;
+	int pre_voltage, pre_vsram, new_vsram, vsram, voltage, ret;
+	int retry_max = drv->vtrack_max;
+
+	if (!drv->sram_reg) {
+		ret = regulator_set_voltage(drv->proc_reg, new_voltage,
+					    drv->soc_data->proc_max_volt);
+		return ret;
+	}
+
+	pre_voltage = regulator_get_voltage(drv->proc_reg);
+	if (pre_voltage < 0) {
+		dev_err(dev, "invalid vproc value: %d\n", pre_voltage);
+		return pre_voltage;
+	}
+
+	pre_vsram = regulator_get_voltage(drv->sram_reg);
+	if (pre_vsram < 0) {
+		dev_err(dev, "invalid vsram value: %d\n", pre_vsram);
+		return pre_vsram;
+	}
+
+	new_vsram = clamp(new_voltage + soc_data->min_volt_shift,
+			  soc_data->sram_min_volt, soc_data->sram_max_volt);
+
+	do {
+		if (pre_voltage <= new_voltage) {
+			vsram = clamp(pre_voltage + soc_data->max_volt_shift,
+				      soc_data->sram_min_volt, new_vsram);
+			ret = regulator_set_voltage(drv->sram_reg, vsram,
+						    soc_data->sram_max_volt);
+			if (ret)
+				return ret;
+
+			if (vsram == soc_data->sram_max_volt ||
+			    new_vsram == soc_data->sram_min_volt)
+				voltage = new_voltage;
+			else
+				voltage = vsram - soc_data->min_volt_shift;
+
+			ret = regulator_set_voltage(drv->proc_reg, voltage,
+						    soc_data->proc_max_volt);
+			if (ret) {
+				regulator_set_voltage(drv->sram_reg, pre_vsram,
+						      soc_data->sram_max_volt);
+				return ret;
+			}
+		} else if (pre_voltage > new_voltage) {
+			voltage = max(new_voltage,
+				      pre_vsram - soc_data->max_volt_shift);
+			ret = regulator_set_voltage(drv->proc_reg, voltage,
+						    soc_data->proc_max_volt);
+			if (ret)
+				return ret;
+
+			if (voltage == new_voltage)
+				vsram = new_vsram;
+			else
+				vsram = max(new_vsram,
+					    voltage + soc_data->min_volt_shift);
+
+			ret = regulator_set_voltage(drv->sram_reg, vsram,
+						    soc_data->sram_max_volt);
+			if (ret) {
+				regulator_set_voltage(drv->proc_reg, pre_voltage,
+						      soc_data->proc_max_volt);
+				return ret;
+			}
+		}
+
+		pre_voltage = voltage;
+		pre_vsram = vsram;
+
+		if (--retry_max < 0) {
+			dev_err(dev,
+				"over loop count, failed to set voltage\n");
+			return -EINVAL;
+		}
+	} while (voltage != new_voltage || vsram != new_vsram);
+
+	return 0;
+}
+
+static int mtk_ccifreq_target(struct device *dev, unsigned long *freq,
+			      u32 flags)
+{
+	struct mtk_ccifreq_drv *drv = dev_get_drvdata(dev);
+	struct clk *cci_pll = clk_get_parent(drv->cci_clk);
+	struct dev_pm_opp *opp;
+	unsigned long opp_rate;
+	int voltage, pre_voltage, inter_voltage, target_voltage, ret;
+
+	if (!drv)
+		return -EINVAL;
+
+	if (drv->pre_freq == *freq)
+		return 0;
+
+	inter_voltage = drv->inter_voltage;
+
+	opp_rate = *freq;
+	opp = devfreq_recommended_opp(dev, &opp_rate, 1);
+	if (IS_ERR(opp)) {
+		dev_err(dev, "failed to find opp for freq: %ld\n", opp_rate);
+		return PTR_ERR(opp);
+	}
+
+	mutex_lock(&drv->reg_lock);
+
+	voltage = dev_pm_opp_get_voltage(opp);
+	dev_pm_opp_put(opp);
+
+	pre_voltage = regulator_get_voltage(drv->proc_reg);
+	if (pre_voltage < 0) {
+		dev_err(dev, "invalid vproc value: %d\n", pre_voltage);
+		ret = pre_voltage;
+		goto out_unlock;
+	}
+
+	/* scale up: set voltage first then freq. */
+	target_voltage = max(inter_voltage, voltage);
+	if (pre_voltage <= target_voltage) {
+		ret = mtk_ccifreq_set_voltage(drv, target_voltage);
+		if (ret) {
+			dev_err(dev, "failed to scale up voltage\n");
+			goto out_restore_voltage;
+		}
+	}
+
+	/* switch the cci clock to intermediate clock source. */
+	ret = clk_set_parent(drv->cci_clk, drv->inter_clk);
+	if (ret) {
+		dev_err(dev, "failed to re-parent cci clock\n");
+		goto out_restore_voltage;
+	}
+
+	/* set the original clock to target rate. */
+	ret = clk_set_rate(cci_pll, *freq);
+	if (ret) {
+		dev_err(dev, "failed to set cci pll rate: %d\n", ret);
+		clk_set_parent(drv->cci_clk, cci_pll);
+		goto out_restore_voltage;
+	}
+
+	/* switch the cci clock back to the original clock source. */
+	ret = clk_set_parent(drv->cci_clk, cci_pll);
+	if (ret) {
+		dev_err(dev, "failed to re-parent cci clock\n");
+		mtk_ccifreq_set_voltage(drv, inter_voltage);
+		goto out_unlock;
+	}
+
+	/*
+	 * If the new voltage is lower than the intermediate voltage or the
+	 * original voltage, scale down to the new voltage.
+	 */
+	if (voltage < inter_voltage || voltage < pre_voltage) {
+		ret = mtk_ccifreq_set_voltage(drv, voltage);
+		if (ret) {
+			dev_err(dev, "failed to scale down voltage\n");
+			goto out_unlock;
+		}
+	}
+
+	drv->pre_freq = *freq;
+	mutex_unlock(&drv->reg_lock);
+
+	return 0;
+
+out_restore_voltage:
+	mtk_ccifreq_set_voltage(drv, pre_voltage);
+
+out_unlock:
+	mutex_unlock(&drv->reg_lock);
+	return ret;
+}
+
+static int mtk_ccifreq_opp_notifier(struct notifier_block *nb,
+				    unsigned long event, void *data)
+{
+	struct dev_pm_opp *opp = data;
+	struct mtk_ccifreq_drv *drv;
+	unsigned long freq, volt;
+
+	drv = container_of(nb, struct mtk_ccifreq_drv, opp_nb);
+
+	if (event == OPP_EVENT_ADJUST_VOLTAGE) {
+		freq = dev_pm_opp_get_freq(opp);
+
+		mutex_lock(&drv->reg_lock);
+		/* current opp item is changed */
+		if (freq == drv->pre_freq) {
+			volt = dev_pm_opp_get_voltage(opp);
+			mtk_ccifreq_set_voltage(drv, volt);
+		}
+		mutex_unlock(&drv->reg_lock);
+	}
+
+	return 0;
+}
+
+static struct devfreq_dev_profile mtk_ccifreq_profile = {
+	.target = mtk_ccifreq_target,
+};
+
+static int mtk_ccifreq_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct mtk_ccifreq_drv *drv;
+	struct devfreq_passive_data *passive_data;
+	struct dev_pm_opp *opp;
+	unsigned long rate, opp_volt;
+	int ret;
+
+	drv = devm_kzalloc(dev, sizeof(*drv), GFP_KERNEL);
+	if (!drv)
+		return -ENOMEM;
+
+	drv->dev = dev;
+	drv->soc_data = (const struct mtk_ccifreq_platform_data *)
+				of_device_get_match_data(&pdev->dev);
+	mutex_init(&drv->reg_lock);
+	platform_set_drvdata(pdev, drv);
+
+	drv->cci_clk = devm_clk_get(dev, "cci");
+	if (IS_ERR(drv->cci_clk)) {
+		ret = PTR_ERR(drv->cci_clk);
+		return dev_err_probe(dev, ret, "failed to get cci clk\n");
+	}
+
+	drv->inter_clk = devm_clk_get(dev, "intermediate");
+	if (IS_ERR(drv->inter_clk)) {
+		ret = PTR_ERR(drv->inter_clk);
+		return dev_err_probe(dev, ret,
+				     "failed to get intermediate clk\n");
+	}
+
+	drv->proc_reg = devm_regulator_get_optional(dev, "proc");
+	if (IS_ERR(drv->proc_reg)) {
+		ret = PTR_ERR(drv->proc_reg);
+		return dev_err_probe(dev, ret,
+				     "failed to get proc regulator\n");
+	}
+
+	ret = regulator_enable(drv->proc_reg);
+	if (ret) {
+		dev_err(dev, "failed to enable proc regulator\n");
+		return ret;
+	}
+
+	drv->sram_reg = devm_regulator_get_optional(dev, "sram");
+	if (IS_ERR(drv->sram_reg))
+		drv->sram_reg = NULL;
+	else {
+		ret = regulator_enable(drv->sram_reg);
+		if (ret) {
+			dev_err(dev, "failed to enable sram regulator\n");
+			goto out_free_resources;
+		}
+	}
+
+	/*
+	 * We assume min voltage is 0 and tracking target voltage using
+	 * min_volt_shift for each iteration.
+	 * The retry_max is 3 times of expected iteration count.
+	 */
+	drv->vtrack_max = 3 * DIV_ROUND_UP(max(drv->soc_data->sram_max_volt,
+					       drv->soc_data->proc_max_volt),
+					   drv->soc_data->min_volt_shift);
+
+	ret = clk_prepare_enable(drv->cci_clk);
+	if (ret)
+		goto out_free_resources;
+
+	ret = dev_pm_opp_of_add_table(dev);
+	if (ret) {
+		dev_err(dev, "failed to add opp table: %d\n", ret);
+		goto out_disable_cci_clk;
+	}
+
+	rate = clk_get_rate(drv->inter_clk);
+	opp = dev_pm_opp_find_freq_ceil(dev, &rate);
+	if (IS_ERR(opp)) {
+		ret = PTR_ERR(opp);
+		dev_err(dev, "failed to get intermediate opp: %d\n", ret);
+		goto out_remove_opp_table;
+	}
+	drv->inter_voltage = dev_pm_opp_get_voltage(opp);
+	dev_pm_opp_put(opp);
+
+	rate = U32_MAX;
+	opp = dev_pm_opp_find_freq_floor(drv->dev, &rate);
+	if (IS_ERR(opp)) {
+		dev_err(dev, "failed to get opp\n");
+		ret = PTR_ERR(opp);
+		goto out_remove_opp_table;
+	}
+
+	opp_volt = dev_pm_opp_get_voltage(opp);
+	dev_pm_opp_put(opp);
+	ret = mtk_ccifreq_set_voltage(drv, opp_volt);
+	if (ret) {
+		dev_err(dev, "failed to scale to highest voltage %lu in proc_reg\n",
+			opp_volt);
+		goto out_remove_opp_table;
+	}
+
+	passive_data = devm_kzalloc(dev, sizeof(*passive_data), GFP_KERNEL);
+	if (!passive_data) {
+		ret = -ENOMEM;
+		goto out_remove_opp_table;
+	}
+
+	passive_data->parent_type = CPUFREQ_PARENT_DEV;
+	drv->devfreq = devm_devfreq_add_device(dev, &mtk_ccifreq_profile,
+					       DEVFREQ_GOV_PASSIVE,
+					       passive_data);
+	if (IS_ERR(drv->devfreq)) {
+		ret = -EPROBE_DEFER;
+		dev_err(dev, "failed to add devfreq device: %ld\n",
+			PTR_ERR(drv->devfreq));
+		goto out_remove_opp_table;
+	}
+
+	drv->opp_nb.notifier_call = mtk_ccifreq_opp_notifier;
+	ret = dev_pm_opp_register_notifier(dev, &drv->opp_nb);
+	if (ret) {
+		dev_err(dev, "failed to register opp notifier: %d\n", ret);
+		goto out_remove_opp_table;
+	}
+	return 0;
+
+out_remove_opp_table:
+	dev_pm_opp_of_remove_table(dev);
+
+out_disable_cci_clk:
+	clk_disable_unprepare(drv->cci_clk);
+
+out_free_resources:
+	if (regulator_is_enabled(drv->proc_reg))
+		regulator_disable(drv->proc_reg);
+	if (drv->sram_reg && regulator_is_enabled(drv->sram_reg))
+		regulator_disable(drv->sram_reg);
+
+	return ret;
+}
+
+static int mtk_ccifreq_remove(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct mtk_ccifreq_drv *drv;
+
+	drv = platform_get_drvdata(pdev);
+
+	dev_pm_opp_unregister_notifier(dev, &drv->opp_nb);
+	dev_pm_opp_of_remove_table(dev);
+	clk_disable_unprepare(drv->cci_clk);
+	regulator_disable(drv->proc_reg);
+	if (drv->sram_reg)
+		regulator_disable(drv->sram_reg);
+
+	return 0;
+}
+
+static const struct mtk_ccifreq_platform_data mt8183_platform_data = {
+	.min_volt_shift = 100000,
+	.max_volt_shift = 200000,
+	.proc_max_volt = 1150000,
+};
+
+static const struct mtk_ccifreq_platform_data mt8186_platform_data = {
+	.min_volt_shift = 100000,
+	.max_volt_shift = 250000,
+	.proc_max_volt = 1118750,
+	.sram_min_volt = 850000,
+	.sram_max_volt = 1118750,
+};
+
+static const struct of_device_id mtk_ccifreq_machines[] = {
+	{ .compatible = "mediatek,mt8183-cci", .data = &mt8183_platform_data },
+	{ .compatible = "mediatek,mt8186-cci", .data = &mt8186_platform_data },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, mtk_ccifreq_machines);
+
+static struct platform_driver mtk_ccifreq_platdrv = {
+	.probe	= mtk_ccifreq_probe,
+	.remove	= mtk_ccifreq_remove,
+	.driver = {
+		.name = "mtk-ccifreq",
+		.of_match_table = mtk_ccifreq_machines,
+	},
+};
+module_platform_driver(mtk_ccifreq_platdrv);
+
+MODULE_DESCRIPTION("MediaTek CCI devfreq driver");
+MODULE_AUTHOR("Jia-Wei Chang <jia-wei.chang@mediatek.com>");
+MODULE_LICENSE("GPL v2");
-- 
2.18.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v7 2/2] PM / devfreq: mediatek: Introduce MediaTek CCI devfreq driver

[Johnson Wang]

We introduce a devfreq driver for the MediaTek Cache Coherent Interconnect
(CCI) used by some MediaTek SoCs.

In this driver, we use the passive devfreq driver to get target frequencies
and adjust voltages accordingly. In MT8183 and MT8186, the MediaTek CCI
is supplied by the same regulators with the little core CPUs.

Signed-off-by: Jia-Wei Chang <jia-wei.chang@mediatek.com>
Signed-off-by: Johnson Wang <johnson.wang@mediatek.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
---
 drivers/devfreq/Kconfig           |  10 +
 drivers/devfreq/Makefile          |   1 +
 drivers/devfreq/mtk-cci-devfreq.c | 440 ++++++++++++++++++++++++++++++
 3 files changed, 451 insertions(+)
 create mode 100644 drivers/devfreq/mtk-cci-devfreq.c

diff --git a/drivers/devfreq/Kconfig b/drivers/devfreq/Kconfig
index 87eb2b837e68..9754d8b31621 100644
--- a/drivers/devfreq/Kconfig
+++ b/drivers/devfreq/Kconfig
@@ -120,6 +120,16 @@ config ARM_TEGRA_DEVFREQ
 	  It reads ACTMON counters of memory controllers and adjusts the
 	  operating frequencies and voltages with OPP support.
 
+config ARM_MEDIATEK_CCI_DEVFREQ
+	tristate "MEDIATEK CCI DEVFREQ Driver"
+	depends on ARM_MEDIATEK_CPUFREQ || COMPILE_TEST
+	select DEVFREQ_GOV_PASSIVE
+	help
+	  This adds a devfreq driver for MediaTek Cache Coherent Interconnect
+	  which is shared the same regulators with the cpu cluster. It can track
+	  buck voltages and update a proper CCI frequency. Use the notification
+	  to get the regulator status.
+
 config ARM_RK3399_DMC_DEVFREQ
 	tristate "ARM RK3399 DMC DEVFREQ Driver"
 	depends on (ARCH_ROCKCHIP && HAVE_ARM_SMCCC) || \
diff --git a/drivers/devfreq/Makefile b/drivers/devfreq/Makefile
index 0b6be92a25d9..bf40d04928d0 100644
--- a/drivers/devfreq/Makefile
+++ b/drivers/devfreq/Makefile
@@ -11,6 +11,7 @@ obj-$(CONFIG_DEVFREQ_GOV_PASSIVE)	+= governor_passive.o
 obj-$(CONFIG_ARM_EXYNOS_BUS_DEVFREQ)	+= exynos-bus.o
 obj-$(CONFIG_ARM_IMX_BUS_DEVFREQ)	+= imx-bus.o
 obj-$(CONFIG_ARM_IMX8M_DDRC_DEVFREQ)	+= imx8m-ddrc.o
+obj-$(CONFIG_ARM_MEDIATEK_CCI_DEVFREQ)	+= mtk-cci-devfreq.o
 obj-$(CONFIG_ARM_RK3399_DMC_DEVFREQ)	+= rk3399_dmc.o
 obj-$(CONFIG_ARM_SUN8I_A33_MBUS_DEVFREQ)	+= sun8i-a33-mbus.o
 obj-$(CONFIG_ARM_TEGRA_DEVFREQ)		+= tegra30-devfreq.o
diff --git a/drivers/devfreq/mtk-cci-devfreq.c b/drivers/devfreq/mtk-cci-devfreq.c
new file mode 100644
index 000000000000..71abb3fbd042
--- /dev/null
+++ b/drivers/devfreq/mtk-cci-devfreq.c
@@ -0,0 +1,440 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2022 MediaTek Inc.
+ */
+
+#include <linux/clk.h>
+#include <linux/devfreq.h>
+#include <linux/minmax.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/pm_opp.h>
+#include <linux/regulator/consumer.h>
+
+struct mtk_ccifreq_platform_data {
+	int min_volt_shift;
+	int max_volt_shift;
+	int proc_max_volt;
+	int sram_min_volt;
+	int sram_max_volt;
+};
+
+struct mtk_ccifreq_drv {
+	struct device *dev;
+	struct devfreq *devfreq;
+	struct regulator *proc_reg;
+	struct regulator *sram_reg;
+	struct clk *cci_clk;
+	struct clk *inter_clk;
+	int inter_voltage;
+	unsigned long pre_freq;
+	/* Avoid race condition for regulators between notify and policy */
+	struct mutex reg_lock;
+	struct notifier_block opp_nb;
+	const struct mtk_ccifreq_platform_data *soc_data;
+	int vtrack_max;
+};
+
+static int mtk_ccifreq_set_voltage(struct mtk_ccifreq_drv *drv, int new_voltage)
+{
+	const struct mtk_ccifreq_platform_data *soc_data = drv->soc_data;
+	struct device *dev = drv->dev;
+	int pre_voltage, pre_vsram, new_vsram, vsram, voltage, ret;
+	int retry_max = drv->vtrack_max;
+
+	if (!drv->sram_reg) {
+		ret = regulator_set_voltage(drv->proc_reg, new_voltage,
+					    drv->soc_data->proc_max_volt);
+		return ret;
+	}
+
+	pre_voltage = regulator_get_voltage(drv->proc_reg);
+	if (pre_voltage < 0) {
+		dev_err(dev, "invalid vproc value: %d\n", pre_voltage);
+		return pre_voltage;
+	}
+
+	pre_vsram = regulator_get_voltage(drv->sram_reg);
+	if (pre_vsram < 0) {
+		dev_err(dev, "invalid vsram value: %d\n", pre_vsram);
+		return pre_vsram;
+	}
+
+	new_vsram = clamp(new_voltage + soc_data->min_volt_shift,
+			  soc_data->sram_min_volt, soc_data->sram_max_volt);
+
+	do {
+		if (pre_voltage <= new_voltage) {
+			vsram = clamp(pre_voltage + soc_data->max_volt_shift,
+				      soc_data->sram_min_volt, new_vsram);
+			ret = regulator_set_voltage(drv->sram_reg, vsram,
+						    soc_data->sram_max_volt);
+			if (ret)
+				return ret;
+
+			if (vsram == soc_data->sram_max_volt ||
+			    new_vsram == soc_data->sram_min_volt)
+				voltage = new_voltage;
+			else
+				voltage = vsram - soc_data->min_volt_shift;
+
+			ret = regulator_set_voltage(drv->proc_reg, voltage,
+						    soc_data->proc_max_volt);
+			if (ret) {
+				regulator_set_voltage(drv->sram_reg, pre_vsram,
+						      soc_data->sram_max_volt);
+				return ret;
+			}
+		} else if (pre_voltage > new_voltage) {
+			voltage = max(new_voltage,
+				      pre_vsram - soc_data->max_volt_shift);
+			ret = regulator_set_voltage(drv->proc_reg, voltage,
+						    soc_data->proc_max_volt);
+			if (ret)
+				return ret;
+
+			if (voltage == new_voltage)
+				vsram = new_vsram;
+			else
+				vsram = max(new_vsram,
+					    voltage + soc_data->min_volt_shift);
+
+			ret = regulator_set_voltage(drv->sram_reg, vsram,
+						    soc_data->sram_max_volt);
+			if (ret) {
+				regulator_set_voltage(drv->proc_reg, pre_voltage,
+						      soc_data->proc_max_volt);
+				return ret;
+			}
+		}
+
+		pre_voltage = voltage;
+		pre_vsram = vsram;
+
+		if (--retry_max < 0) {
+			dev_err(dev,
+				"over loop count, failed to set voltage\n");
+			return -EINVAL;
+		}
+	} while (voltage != new_voltage || vsram != new_vsram);
+
+	return 0;
+}
+
+static int mtk_ccifreq_target(struct device *dev, unsigned long *freq,
+			      u32 flags)
+{
+	struct mtk_ccifreq_drv *drv = dev_get_drvdata(dev);
+	struct clk *cci_pll = clk_get_parent(drv->cci_clk);
+	struct dev_pm_opp *opp;
+	unsigned long opp_rate;
+	int voltage, pre_voltage, inter_voltage, target_voltage, ret;
+
+	if (!drv)
+		return -EINVAL;
+
+	if (drv->pre_freq == *freq)
+		return 0;
+
+	inter_voltage = drv->inter_voltage;
+
+	opp_rate = *freq;
+	opp = devfreq_recommended_opp(dev, &opp_rate, 1);
+	if (IS_ERR(opp)) {
+		dev_err(dev, "failed to find opp for freq: %ld\n", opp_rate);
+		return PTR_ERR(opp);
+	}
+
+	mutex_lock(&drv->reg_lock);
+
+	voltage = dev_pm_opp_get_voltage(opp);
+	dev_pm_opp_put(opp);
+
+	pre_voltage = regulator_get_voltage(drv->proc_reg);
+	if (pre_voltage < 0) {
+		dev_err(dev, "invalid vproc value: %d\n", pre_voltage);
+		ret = pre_voltage;
+		goto out_unlock;
+	}
+
+	/* scale up: set voltage first then freq. */
+	target_voltage = max(inter_voltage, voltage);
+	if (pre_voltage <= target_voltage) {
+		ret = mtk_ccifreq_set_voltage(drv, target_voltage);
+		if (ret) {
+			dev_err(dev, "failed to scale up voltage\n");
+			goto out_restore_voltage;
+		}
+	}
+
+	/* switch the cci clock to intermediate clock source. */
+	ret = clk_set_parent(drv->cci_clk, drv->inter_clk);
+	if (ret) {
+		dev_err(dev, "failed to re-parent cci clock\n");
+		goto out_restore_voltage;
+	}
+
+	/* set the original clock to target rate. */
+	ret = clk_set_rate(cci_pll, *freq);
+	if (ret) {
+		dev_err(dev, "failed to set cci pll rate: %d\n", ret);
+		clk_set_parent(drv->cci_clk, cci_pll);
+		goto out_restore_voltage;
+	}
+
+	/* switch the cci clock back to the original clock source. */
+	ret = clk_set_parent(drv->cci_clk, cci_pll);
+	if (ret) {
+		dev_err(dev, "failed to re-parent cci clock\n");
+		mtk_ccifreq_set_voltage(drv, inter_voltage);
+		goto out_unlock;
+	}
+
+	/*
+	 * If the new voltage is lower than the intermediate voltage or the
+	 * original voltage, scale down to the new voltage.
+	 */
+	if (voltage < inter_voltage || voltage < pre_voltage) {
+		ret = mtk_ccifreq_set_voltage(drv, voltage);
+		if (ret) {
+			dev_err(dev, "failed to scale down voltage\n");
+			goto out_unlock;
+		}
+	}
+
+	drv->pre_freq = *freq;
+	mutex_unlock(&drv->reg_lock);
+
+	return 0;
+
+out_restore_voltage:
+	mtk_ccifreq_set_voltage(drv, pre_voltage);
+
+out_unlock:
+	mutex_unlock(&drv->reg_lock);
+	return ret;
+}
+
+static int mtk_ccifreq_opp_notifier(struct notifier_block *nb,
+				    unsigned long event, void *data)
+{
+	struct dev_pm_opp *opp = data;
+	struct mtk_ccifreq_drv *drv;
+	unsigned long freq, volt;
+
+	drv = container_of(nb, struct mtk_ccifreq_drv, opp_nb);
+
+	if (event == OPP_EVENT_ADJUST_VOLTAGE) {
+		freq = dev_pm_opp_get_freq(opp);
+
+		mutex_lock(&drv->reg_lock);
+		/* current opp item is changed */
+		if (freq == drv->pre_freq) {
+			volt = dev_pm_opp_get_voltage(opp);
+			mtk_ccifreq_set_voltage(drv, volt);
+		}
+		mutex_unlock(&drv->reg_lock);
+	}
+
+	return 0;
+}
+
+static struct devfreq_dev_profile mtk_ccifreq_profile = {
+	.target = mtk_ccifreq_target,
+};
+
+static int mtk_ccifreq_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct mtk_ccifreq_drv *drv;
+	struct devfreq_passive_data *passive_data;
+	struct dev_pm_opp *opp;
+	unsigned long rate, opp_volt;
+	int ret;
+
+	drv = devm_kzalloc(dev, sizeof(*drv), GFP_KERNEL);
+	if (!drv)
+		return -ENOMEM;
+
+	drv->dev = dev;
+	drv->soc_data = (const struct mtk_ccifreq_platform_data *)
+				of_device_get_match_data(&pdev->dev);
+	mutex_init(&drv->reg_lock);
+	platform_set_drvdata(pdev, drv);
+
+	drv->cci_clk = devm_clk_get(dev, "cci");
+	if (IS_ERR(drv->cci_clk)) {
+		ret = PTR_ERR(drv->cci_clk);
+		return dev_err_probe(dev, ret, "failed to get cci clk\n");
+	}
+
+	drv->inter_clk = devm_clk_get(dev, "intermediate");
+	if (IS_ERR(drv->inter_clk)) {
+		ret = PTR_ERR(drv->inter_clk);
+		return dev_err_probe(dev, ret,
+				     "failed to get intermediate clk\n");
+	}
+
+	drv->proc_reg = devm_regulator_get_optional(dev, "proc");
+	if (IS_ERR(drv->proc_reg)) {
+		ret = PTR_ERR(drv->proc_reg);
+		return dev_err_probe(dev, ret,
+				     "failed to get proc regulator\n");
+	}
+
+	ret = regulator_enable(drv->proc_reg);
+	if (ret) {
+		dev_err(dev, "failed to enable proc regulator\n");
+		return ret;
+	}
+
+	drv->sram_reg = devm_regulator_get_optional(dev, "sram");
+	if (IS_ERR(drv->sram_reg))
+		drv->sram_reg = NULL;
+	else {
+		ret = regulator_enable(drv->sram_reg);
+		if (ret) {
+			dev_err(dev, "failed to enable sram regulator\n");
+			goto out_free_resources;
+		}
+	}
+
+	/*
+	 * We assume min voltage is 0 and tracking target voltage using
+	 * min_volt_shift for each iteration.
+	 * The retry_max is 3 times of expected iteration count.
+	 */
+	drv->vtrack_max = 3 * DIV_ROUND_UP(max(drv->soc_data->sram_max_volt,
+					       drv->soc_data->proc_max_volt),
+					   drv->soc_data->min_volt_shift);
+
+	ret = clk_prepare_enable(drv->cci_clk);
+	if (ret)
+		goto out_free_resources;
+
+	ret = dev_pm_opp_of_add_table(dev);
+	if (ret) {
+		dev_err(dev, "failed to add opp table: %d\n", ret);
+		goto out_disable_cci_clk;
+	}
+
+	rate = clk_get_rate(drv->inter_clk);
+	opp = dev_pm_opp_find_freq_ceil(dev, &rate);
+	if (IS_ERR(opp)) {
+		ret = PTR_ERR(opp);
+		dev_err(dev, "failed to get intermediate opp: %d\n", ret);
+		goto out_remove_opp_table;
+	}
+	drv->inter_voltage = dev_pm_opp_get_voltage(opp);
+	dev_pm_opp_put(opp);
+
+	rate = U32_MAX;
+	opp = dev_pm_opp_find_freq_floor(drv->dev, &rate);
+	if (IS_ERR(opp)) {
+		dev_err(dev, "failed to get opp\n");
+		ret = PTR_ERR(opp);
+		goto out_remove_opp_table;
+	}
+
+	opp_volt = dev_pm_opp_get_voltage(opp);
+	dev_pm_opp_put(opp);
+	ret = mtk_ccifreq_set_voltage(drv, opp_volt);
+	if (ret) {
+		dev_err(dev, "failed to scale to highest voltage %lu in proc_reg\n",
+			opp_volt);
+		goto out_remove_opp_table;
+	}
+
+	passive_data = devm_kzalloc(dev, sizeof(*passive_data), GFP_KERNEL);
+	if (!passive_data) {
+		ret = -ENOMEM;
+		goto out_remove_opp_table;
+	}
+
+	passive_data->parent_type = CPUFREQ_PARENT_DEV;
+	drv->devfreq = devm_devfreq_add_device(dev, &mtk_ccifreq_profile,
+					       DEVFREQ_GOV_PASSIVE,
+					       passive_data);
+	if (IS_ERR(drv->devfreq)) {
+		ret = -EPROBE_DEFER;
+		dev_err(dev, "failed to add devfreq device: %ld\n",
+			PTR_ERR(drv->devfreq));
+		goto out_remove_opp_table;
+	}
+
+	drv->opp_nb.notifier_call = mtk_ccifreq_opp_notifier;
+	ret = dev_pm_opp_register_notifier(dev, &drv->opp_nb);
+	if (ret) {
+		dev_err(dev, "failed to register opp notifier: %d\n", ret);
+		goto out_remove_opp_table;
+	}
+	return 0;
+
+out_remove_opp_table:
+	dev_pm_opp_of_remove_table(dev);
+
+out_disable_cci_clk:
+	clk_disable_unprepare(drv->cci_clk);
+
+out_free_resources:
+	if (regulator_is_enabled(drv->proc_reg))
+		regulator_disable(drv->proc_reg);
+	if (drv->sram_reg && regulator_is_enabled(drv->sram_reg))
+		regulator_disable(drv->sram_reg);
+
+	return ret;
+}
+
+static int mtk_ccifreq_remove(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct mtk_ccifreq_drv *drv;
+
+	drv = platform_get_drvdata(pdev);
+
+	dev_pm_opp_unregister_notifier(dev, &drv->opp_nb);
+	dev_pm_opp_of_remove_table(dev);
+	clk_disable_unprepare(drv->cci_clk);
+	regulator_disable(drv->proc_reg);
+	if (drv->sram_reg)
+		regulator_disable(drv->sram_reg);
+
+	return 0;
+}
+
+static const struct mtk_ccifreq_platform_data mt8183_platform_data = {
+	.min_volt_shift = 100000,
+	.max_volt_shift = 200000,
+	.proc_max_volt = 1150000,
+};
+
+static const struct mtk_ccifreq_platform_data mt8186_platform_data = {
+	.min_volt_shift = 100000,
+	.max_volt_shift = 250000,
+	.proc_max_volt = 1118750,
+	.sram_min_volt = 850000,
+	.sram_max_volt = 1118750,
+};
+
+static const struct of_device_id mtk_ccifreq_machines[] = {
+	{ .compatible = "mediatek,mt8183-cci", .data = &mt8183_platform_data },
+	{ .compatible = "mediatek,mt8186-cci", .data = &mt8186_platform_data },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, mtk_ccifreq_machines);
+
+static struct platform_driver mtk_ccifreq_platdrv = {
+	.probe	= mtk_ccifreq_probe,
+	.remove	= mtk_ccifreq_remove,
+	.driver = {
+		.name = "mtk-ccifreq",
+		.of_match_table = mtk_ccifreq_machines,
+	},
+};
+module_platform_driver(mtk_ccifreq_platdrv);
+
+MODULE_DESCRIPTION("MediaTek CCI devfreq driver");
+MODULE_AUTHOR("Jia-Wei Chang <jia-wei.chang@mediatek.com>");
+MODULE_LICENSE("GPL v2");
-- 
2.18.0

Re: [PATCH v7 2/2] PM / devfreq: mediatek: Introduce MediaTek CCI devfreq driver

[AngeloGioacchino Del Regno]

Il 07/06/22 16:05, Johnson Wang ha scritto:
> We introduce a devfreq driver for the MediaTek Cache Coherent Interconnect
> (CCI) used by some MediaTek SoCs.
> 
> In this driver, we use the passive devfreq driver to get target frequencies
> and adjust voltages accordingly. In MT8183 and MT8186, the MediaTek CCI
> is supplied by the same regulators with the little core CPUs.
> 
> Signed-off-by: Jia-Wei Chang <jia-wei.chang@mediatek.com>
> Signed-off-by: Johnson Wang <johnson.wang@mediatek.com>
> Acked-by: Chanwoo Choi <cw00.choi@samsung.com>

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>


_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

Re: [PATCH v7 2/2] PM / devfreq: mediatek: Introduce MediaTek CCI devfreq driver

[AngeloGioacchino Del Regno]

Il 07/06/22 16:05, Johnson Wang ha scritto:
> We introduce a devfreq driver for the MediaTek Cache Coherent Interconnect
> (CCI) used by some MediaTek SoCs.
> 
> In this driver, we use the passive devfreq driver to get target frequencies
> and adjust voltages accordingly. In MT8183 and MT8186, the MediaTek CCI
> is supplied by the same regulators with the little core CPUs.
> 
> Signed-off-by: Jia-Wei Chang <jia-wei.chang@mediatek.com>
> Signed-off-by: Johnson Wang <johnson.wang@mediatek.com>
> Acked-by: Chanwoo Choi <cw00.choi@samsung.com>

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v7 2/2] PM / devfreq: mediatek: Introduce MediaTek CCI devfreq driver

[AngeloGioacchino Del Regno]

Il 07/06/22 16:05, Johnson Wang ha scritto:
> We introduce a devfreq driver for the MediaTek Cache Coherent Interconnect
> (CCI) used by some MediaTek SoCs.
> 
> In this driver, we use the passive devfreq driver to get target frequencies
> and adjust voltages accordingly. In MT8183 and MT8186, the MediaTek CCI
> is supplied by the same regulators with the little core CPUs.
> 
> Signed-off-by: Jia-Wei Chang <jia-wei.chang@mediatek.com>
> Signed-off-by: Johnson Wang <johnson.wang@mediatek.com>
> Acked-by: Chanwoo Choi <cw00.choi@samsung.com>

Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>

Re: [PATCH v7 0/2] Introduce MediaTek CCI devfreq driver

[Chanwoo Choi]

On 6/7/22 11:05 PM, Johnson Wang wrote:
> The Cache Coherent Interconnect (CCI) is the management of cache
> coherency by hardware. CCI DEVFREQ is DVFS driver for power saving by
> scaling clock frequency and supply voltage of CCI. CCI uses the same
> input clock source and power rail as LITTLE CPUs on Mediatek SoCs.
> 
> This series depends on:
> Chanwoo's repo: kernel/git/chanwoo/linux.git
> branch: devfreq-testing
> [1]: PM / devfreq: Export devfreq_get_freq_range symbol within devfreq
> [2]: PM / devfreq: Add cpu based scaling support to passive governor
> [3]: PM / devfreq: passive: Reduce duplicate code when passive_devfreq case
> [4]: PM / devfreq: passive: Update frequency when start governor
> 
> Changes in v7:
> - remove the 'ret' printing from dev_err_probe().
> 
> Changes in v6:
> - Remove unnecessary "goto" statement.
> 
> Changes in v5:
> - Modify some binding description.
> - Remove pre_voltage member.
> - Not to enable/disable intermediate clock.
> - Not to "put" resources that using devm_ variants.
> 
> Resend v4:
> - CC interconnect maintainer.
> - Change sign-off sequence in commit message.
> 
> Changes in v4:
> - Add a maintainer in the binding document.
> - Modify clock description.
> - Add binding document into MAINTAINERS.
> - Replace format specifier %d with %ld.
> 
> Changes in v3:
> - Move binding document to 'interconnect' and rename it.
> - Add COMPILE_TEST dependence symbol.
> - Remove need_voltage_tracking variable.
> - Move mtk_ccifreq_voltage_tracking() code into mtk_ccifreq_set_voltage().
> - Add an interation limit in the while() loop.
> - Replace 'cci_dev' with 'dev'
> - Replace old_* with pre_*
> - Remove of_match_ptr()
> - Use module_platform_driver()
> 
> Changes in v2:
> - Take MT8183 as example in binding document.
> - Use dev_err() instead of pr_err().
> - Use 'goto' statement to handle error case.
> - Clean up driver code.
> 
> Johnson Wang (2):
>   dt-bindings: interconnect: Add MediaTek CCI dt-bindings
>   PM / devfreq: mediatek: Introduce MediaTek CCI devfreq driver
> 
>  .../bindings/interconnect/mediatek,cci.yaml   | 140 ++++++
>  MAINTAINERS                                   |   1 +
>  drivers/devfreq/Kconfig                       |  10 +
>  drivers/devfreq/Makefile                      |   1 +
>  drivers/devfreq/mtk-cci-devfreq.c             | 474 ++++++++++++++++++
>  5 files changed, 626 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/interconnect/mediatek,cci.yaml
>  create mode 100644 drivers/devfreq/mtk-cci-devfreq.c
> 

Applied them. Thanks.

-- 
Best Regards,
Chanwoo Choi
Samsung Electronics

_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

Re: [PATCH v7 0/2] Introduce MediaTek CCI devfreq driver

[Chanwoo Choi]

On 6/7/22 11:05 PM, Johnson Wang wrote:
> The Cache Coherent Interconnect (CCI) is the management of cache
> coherency by hardware. CCI DEVFREQ is DVFS driver for power saving by
> scaling clock frequency and supply voltage of CCI. CCI uses the same
> input clock source and power rail as LITTLE CPUs on Mediatek SoCs.
> 
> This series depends on:
> Chanwoo's repo: kernel/git/chanwoo/linux.git
> branch: devfreq-testing
> [1]: PM / devfreq: Export devfreq_get_freq_range symbol within devfreq
> [2]: PM / devfreq: Add cpu based scaling support to passive governor
> [3]: PM / devfreq: passive: Reduce duplicate code when passive_devfreq case
> [4]: PM / devfreq: passive: Update frequency when start governor
> 
> Changes in v7:
> - remove the 'ret' printing from dev_err_probe().
> 
> Changes in v6:
> - Remove unnecessary "goto" statement.
> 
> Changes in v5:
> - Modify some binding description.
> - Remove pre_voltage member.
> - Not to enable/disable intermediate clock.
> - Not to "put" resources that using devm_ variants.
> 
> Resend v4:
> - CC interconnect maintainer.
> - Change sign-off sequence in commit message.
> 
> Changes in v4:
> - Add a maintainer in the binding document.
> - Modify clock description.
> - Add binding document into MAINTAINERS.
> - Replace format specifier %d with %ld.
> 
> Changes in v3:
> - Move binding document to 'interconnect' and rename it.
> - Add COMPILE_TEST dependence symbol.
> - Remove need_voltage_tracking variable.
> - Move mtk_ccifreq_voltage_tracking() code into mtk_ccifreq_set_voltage().
> - Add an interation limit in the while() loop.
> - Replace 'cci_dev' with 'dev'
> - Replace old_* with pre_*
> - Remove of_match_ptr()
> - Use module_platform_driver()
> 
> Changes in v2:
> - Take MT8183 as example in binding document.
> - Use dev_err() instead of pr_err().
> - Use 'goto' statement to handle error case.
> - Clean up driver code.
> 
> Johnson Wang (2):
>   dt-bindings: interconnect: Add MediaTek CCI dt-bindings
>   PM / devfreq: mediatek: Introduce MediaTek CCI devfreq driver
> 
>  .../bindings/interconnect/mediatek,cci.yaml   | 140 ++++++
>  MAINTAINERS                                   |   1 +
>  drivers/devfreq/Kconfig                       |  10 +
>  drivers/devfreq/Makefile                      |   1 +
>  drivers/devfreq/mtk-cci-devfreq.c             | 474 ++++++++++++++++++
>  5 files changed, 626 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/interconnect/mediatek,cci.yaml
>  create mode 100644 drivers/devfreq/mtk-cci-devfreq.c
> 

Applied them. Thanks.

-- 
Best Regards,
Chanwoo Choi
Samsung Electronics

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v7 0/2] Introduce MediaTek CCI devfreq driver

[Chanwoo Choi]

On 6/7/22 11:05 PM, Johnson Wang wrote:
> The Cache Coherent Interconnect (CCI) is the management of cache
> coherency by hardware. CCI DEVFREQ is DVFS driver for power saving by
> scaling clock frequency and supply voltage of CCI. CCI uses the same
> input clock source and power rail as LITTLE CPUs on Mediatek SoCs.
> 
> This series depends on:
> Chanwoo's repo: kernel/git/chanwoo/linux.git
> branch: devfreq-testing
> [1]: PM / devfreq: Export devfreq_get_freq_range symbol within devfreq
> [2]: PM / devfreq: Add cpu based scaling support to passive governor
> [3]: PM / devfreq: passive: Reduce duplicate code when passive_devfreq case
> [4]: PM / devfreq: passive: Update frequency when start governor
> 
> Changes in v7:
> - remove the 'ret' printing from dev_err_probe().
> 
> Changes in v6:
> - Remove unnecessary "goto" statement.
> 
> Changes in v5:
> - Modify some binding description.
> - Remove pre_voltage member.
> - Not to enable/disable intermediate clock.
> - Not to "put" resources that using devm_ variants.
> 
> Resend v4:
> - CC interconnect maintainer.
> - Change sign-off sequence in commit message.
> 
> Changes in v4:
> - Add a maintainer in the binding document.
> - Modify clock description.
> - Add binding document into MAINTAINERS.
> - Replace format specifier %d with %ld.
> 
> Changes in v3:
> - Move binding document to 'interconnect' and rename it.
> - Add COMPILE_TEST dependence symbol.
> - Remove need_voltage_tracking variable.
> - Move mtk_ccifreq_voltage_tracking() code into mtk_ccifreq_set_voltage().
> - Add an interation limit in the while() loop.
> - Replace 'cci_dev' with 'dev'
> - Replace old_* with pre_*
> - Remove of_match_ptr()
> - Use module_platform_driver()
> 
> Changes in v2:
> - Take MT8183 as example in binding document.
> - Use dev_err() instead of pr_err().
> - Use 'goto' statement to handle error case.
> - Clean up driver code.
> 
> Johnson Wang (2):
>   dt-bindings: interconnect: Add MediaTek CCI dt-bindings
>   PM / devfreq: mediatek: Introduce MediaTek CCI devfreq driver
> 
>  .../bindings/interconnect/mediatek,cci.yaml   | 140 ++++++
>  MAINTAINERS                                   |   1 +
>  drivers/devfreq/Kconfig                       |  10 +
>  drivers/devfreq/Makefile                      |   1 +
>  drivers/devfreq/mtk-cci-devfreq.c             | 474 ++++++++++++++++++
>  5 files changed, 626 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/interconnect/mediatek,cci.yaml
>  create mode 100644 drivers/devfreq/mtk-cci-devfreq.c
> 

Applied them. Thanks.

-- 
Best Regards,
Chanwoo Choi
Samsung Electronics

Re: [PATCH v7 0/2] Introduce MediaTek CCI devfreq driver

[Kevin Hilman]

Johnson Wang <johnson.wang@mediatek.com> writes:

> The Cache Coherent Interconnect (CCI) is the management of cache
> coherency by hardware. CCI DEVFREQ is DVFS driver for power saving by
> scaling clock frequency and supply voltage of CCI. CCI uses the same
> input clock source and power rail as LITTLE CPUs on Mediatek SoCs.

Tested-by: Kevin Hilman <khilman@baylibre.com>

_______________________________________________
Linux-mediatek mailing list
Linux-mediatek@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-mediatek

Re: [PATCH v7 0/2] Introduce MediaTek CCI devfreq driver

[Kevin Hilman]

Johnson Wang <johnson.wang@mediatek.com> writes:

> The Cache Coherent Interconnect (CCI) is the management of cache
> coherency by hardware. CCI DEVFREQ is DVFS driver for power saving by
> scaling clock frequency and supply voltage of CCI. CCI uses the same
> input clock source and power rail as LITTLE CPUs on Mediatek SoCs.

Tested-by: Kevin Hilman <khilman@baylibre.com>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v7 0/2] Introduce MediaTek CCI devfreq driver

[Kevin Hilman]

Johnson Wang <johnson.wang@mediatek.com> writes:

> The Cache Coherent Interconnect (CCI) is the management of cache
> coherency by hardware. CCI DEVFREQ is DVFS driver for power saving by
> scaling clock frequency and supply voltage of CCI. CCI uses the same
> input clock source and power rail as LITTLE CPUs on Mediatek SoCs.

Tested-by: Kevin Hilman <khilman@baylibre.com>