[PATCH V4] ARM: dts: armada388-helios4

[gregory.clement@bootlin.com (Gregory CLEMENT)]

Hi Dennis,
 
 On mar., juin 05 2018, Dennis Gilmore <dennis@ausil.us> wrote:

> The helios4 is a Armada388 based nas board designed by SolidRun and
> based on their SOM. It is sold by kobol.io the dts file came from
> https://raw.githubusercontent.com/armbian/build/master/patch/kernel/mvebu-default/95-helios4-device-tree.patch
> I added a SPDX license line to match the clearfog it says it was based
> on and a compatible line for "kobol,helios4"
>
> Signed-off-by: Dennis Gilmore <dennis@ausil.us>

Applied on mvebu/dt

Thanks,

Gregory

>
> ---
>
> changes since first submission
> change solidrun to kobol in compatible line based on feedback
>
> changes since v2
>
> remove commented out nodes based on feedback
>
> changes since v3
>
> update copyright info for the dts based on a request from kobol
> ---
>  arch/arm/boot/dts/Makefile               |   1 +
>  arch/arm/boot/dts/armada-388-helios4.dts | 313 +++++++++++++++++++++++
>  2 files changed, 314 insertions(+)
>  create mode 100644 arch/arm/boot/dts/armada-388-helios4.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 7e2424957809..490bfd586198 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -1123,6 +1123,7 @@ dtb-$(CONFIG_MACH_ARMADA_38X) += \
>  	armada-388-clearfog-pro.dtb \
>  	armada-388-db.dtb \
>  	armada-388-gp.dtb \
> +	armada-388-helios4.dtb \
>  	armada-388-rd.dtb
>  dtb-$(CONFIG_MACH_ARMADA_39X) += \
>  	armada-398-db.dtb
> diff --git a/arch/arm/boot/dts/armada-388-helios4.dts b/arch/arm/boot/dts/armada-388-helios4.dts
> new file mode 100644
> index 000000000000..705adfa8c680
> --- /dev/null
> +++ b/arch/arm/boot/dts/armada-388-helios4.dts
> @@ -0,0 +1,313 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/*
> + * Device Tree file for Helios4
> + * based on SolidRun Clearfog revision A1 rev 2.0 (88F6828)
> + *
> + *  Copyright (C) 2017 Aditya Prayoga <aditya@kobol.io>
> + *
> + */
> +
> +/dts-v1/;
> +#include "armada-388.dtsi"
> +#include "armada-38x-solidrun-microsom.dtsi"
> +
> +/ {
> +	model = "Helios4";
> +	compatible = "kobol,helios4", "marvell,armada388",
> +		"marvell,armada385", "marvell,armada380";
> +
> +	memory {
> +		device_type = "memory";
> +		reg = <0x00000000 0x80000000>; /* 2 GB */
> +	};
> +
> +	aliases {
> +		/* So that mvebu u-boot can update the MAC addresses */
> +		ethernet1 = &eth0;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	reg_12v: regulator-12v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "power_brick_12V";
> +		regulator-min-microvolt = <12000000>;
> +		regulator-max-microvolt = <12000000>;
> +		regulator-always-on;
> +	};
> +
> +	reg_3p3v: regulator-3p3v {
> +		compatible = "regulator-fixed";
> +		regulator-name = "3P3V";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-always-on;
> +		vin-supply = <&reg_12v>;
> +	};
> +
> +	reg_5p0v_hdd: regulator-5v-hdd {
> +		compatible = "regulator-fixed";
> +		regulator-name = "5V_HDD";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-always-on;
> +		vin-supply = <&reg_12v>;
> +	};
> +
> +	reg_5p0v_usb: regulator-5v-usb {
> +		compatible = "regulator-fixed";
> +		regulator-name = "USB-PWR";
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +		regulator-boot-on;
> +		regulator-always-on;
> +		enable-active-high;
> +		gpio = <&expander0 6 GPIO_ACTIVE_HIGH>;
> +		vin-supply = <&reg_12v>;
> +	};
> +
> +	system-leds {
> +		compatible = "gpio-leds";
> +		status-led {
> +			label = "helios4:green:status";
> +			gpios = <&gpio0 24 GPIO_ACTIVE_LOW>;
> +			linux,default-trigger = "heartbeat";
> +			default-state = "on";
> +		};
> +
> +		fault-led {
> +			label = "helios4:red:fault";
> +			gpios = <&gpio0 25 GPIO_ACTIVE_LOW>;
> +			default-state = "keep";
> +		};
> +	};
> +
> +	io-leds {
> +		compatible = "gpio-leds";
> +		sata1-led {
> +			label = "helios4:green:ata1";
> +			gpios = <&gpio1 17 GPIO_ACTIVE_LOW>;
> +			linux,default-trigger = "ata1";
> +			default-state = "off";
> +		};
> +		sata2-led {
> +			label = "helios4:green:ata2";
> +			gpios = <&gpio1 18 GPIO_ACTIVE_LOW>;
> +			linux,default-trigger = "ata2";
> +			default-state = "off";
> +		};
> +		sata3-led {
> +			label = "helios4:green:ata3";
> +			gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
> +			linux,default-trigger = "ata3";
> +			default-state = "off";
> +		};
> +		sata4-led {
> +			label = "helios4:green:ata4";
> +			gpios = <&gpio1 21 GPIO_ACTIVE_LOW>;
> +			linux,default-trigger = "ata4";
> +			default-state = "off";
> +		};
> +		usb-led {
> +			label = "helios4:green:usb";
> +			gpios = <&gpio1 22 GPIO_ACTIVE_LOW>;
> +			linux,default-trigger = "usb-host";
> +			default-state = "off";
> +		};
> +	};
> +
> +	fan1: j10-pwm {
> +		compatible = "pwm-fan";
> +		pwms = <&gpio1 9 40000>;	/* Target freq:25 kHz */
> +	};
> +
> +	fan2: j17-pwm {
> +		compatible = "pwm-fan";
> +		pwms = <&gpio1 23 40000>;	/* Target freq:25 kHz */
> +	};
> +
> +	usb2_phy: usb2-phy {
> +		compatible = "usb-nop-xceiv";
> +		vbus-regulator = <&reg_5p0v_usb>;
> +	};
> +
> +	usb3_phy: usb3-phy {
> +		compatible = "usb-nop-xceiv";
> +	};
> +
> +	soc {
> +		internal-regs {
> +			i2c at 11000 {
> +				clock-frequency = <400000>;
> +				pinctrl-0 = <&i2c0_pins>;
> +				pinctrl-names = "default";
> +				status = "okay";
> +
> +				/*
> +				 * PCA9655 GPIO expander, up to 1MHz clock.
> +				 *  0-Board Revision bit 0 #
> +				 *  1-Board Revision bit 1 #
> +				 *  5-USB3 overcurrent
> +				 *  6-USB3 power
> +				 */
> +				expander0: gpio-expander at 20 {
> +					/*
> +					 * This is how it should be:
> +					 * compatible = "onnn,pca9655",
> +					 *	 "nxp,pca9555";
> +					 * but you can't do this because of
> +					 * the way I2C works.
> +					 */
> +					compatible = "nxp,pca9555";
> +					gpio-controller;
> +					#gpio-cells = <2>;
> +					reg = <0x20>;
> +					pinctrl-names = "default";
> +					pinctrl-0 = <&pca0_pins>;
> +					interrupt-parent = <&gpio0>;
> +					interrupts = <23 IRQ_TYPE_EDGE_FALLING>;
> +					interrupt-controller;
> +					#interrupt-cells = <2>;
> +
> +					board_rev_bit_0 {
> +						gpio-hog;
> +						gpios = <0 GPIO_ACTIVE_LOW>;
> +						input;
> +						line-name = "board-rev-0";
> +					};
> +					board_rev_bit_1 {
> +						gpio-hog;
> +						gpios = <1 GPIO_ACTIVE_LOW>;
> +						input;
> +						line-name = "board-rev-1";
> +					};
> +					usb3_ilimit {
> +						gpio-hog;
> +						gpios = <5 GPIO_ACTIVE_HIGH>;
> +						input;
> +						line-name = "usb-overcurrent-status";
> +					};
> +				};
> +
> +				temp_sensor: temp at 4c {
> +					compatible = "ti,lm75";
> +					reg = <0x4c>;
> +					vcc-supply = <&reg_3p3v>;
> +				};
> +			};
> +
> +			i2c at 11100 {
> +				/*
> +				 * External I2C Bus for user peripheral
> +				 */
> +				clock-frequency = <400000>;
> +				pinctrl-0 = <&helios_i2c1_pins>;
> +				pinctrl-names = "default";
> +				status = "okay";
> +			};
> +
> +			sata at a8000 {
> +				status = "okay";
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				sata0: sata-port at 0 {
> +					reg = <0>;
> +				};
> +
> +				sata1: sata-port at 1 {
> +					reg = <1>;
> +				};
> +			};
> +
> +			sata at e0000 {
> +				status = "okay";
> +				#address-cells = <1>;
> +				#size-cells = <0>;
> +
> +				sata2: sata-port at 0 {
> +					reg = <0>;
> +				};
> +
> +				sata3: sata-port at 1 {
> +					reg = <1>;
> +				};
> +			};
> +
> +			spi at 10680 {
> +				pinctrl-0 = <&spi1_pins
> +					     &microsom_spi1_cs_pins>;
> +				pinctrl-names = "default";
> +				status = "okay";
> +			};
> +
> +			sdhci at d8000 {
> +				bus-width = <4>;
> +				cd-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
> +				no-1-8-v;
> +				pinctrl-0 = <&helios_sdhci_pins
> +					     &helios_sdhci_cd_pins>;
> +				pinctrl-names = "default";
> +				status = "okay";
> +				vmmc = <&reg_3p3v>;
> +				wp-inverted;
> +			};
> +
> +			usb at 58000 {
> +				usb-phy = <&usb2_phy>;
> +				status = "okay";
> +			};
> +
> +			usb3 at f0000 {
> +				status = "okay";
> +			};
> +
> +			usb3 at f8000 {
> +				status = "okay";
> +			};
> +
> +			pinctrl at 18000 {
> +				pca0_pins: pca0-pins {
> +					marvell,pins = "mpp23";
> +					marvell,function = "gpio";
> +				};
> +				microsom_phy0_int_pins: microsom-phy0-int-pins {
> +					marvell,pins = "mpp18";
> +					marvell,function = "gpio";
> +				};
> +				helios_i2c1_pins: i2c1-pins {
> +					marvell,pins = "mpp26", "mpp27";
> +					marvell,function = "i2c1";
> +				};
> +				helios_sdhci_cd_pins: helios-sdhci-cd-pins {
> +					marvell,pins = "mpp20";
> +					marvell,function = "gpio";
> +				};
> +				helios_sdhci_pins: helios-sdhci-pins {
> +					marvell,pins = "mpp21", "mpp28",
> +						       "mpp37", "mpp38",
> +						       "mpp39", "mpp40";
> +					marvell,function = "sd0";
> +				};
> +				helios_led_pins: helios-led-pins {
> +					marvell,pins = "mpp24", "mpp25",
> +						       "mpp49", "mpp50",
> +						       "mpp52", "mpp53",
> +						       "mpp54";
> +					marvell,function = "gpio";
> +				};
> +				helios_fan_pins: helios-fan-pins {
> +					marvell,pins = "mpp41", "mpp43",
> +						       "mpp48", "mpp55";
> +					marvell,function = "gpio";
> +				};
> +				microsom_spi1_cs_pins: spi1-cs-pins {
> +					marvell,pins = "mpp59";
> +					marvell,function = "spi1";
> +				};
> +			};
> +		};
> +	};
> +};
> -- 
> 2.17.1
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

-- 
Gregory Clement, Bootlin (formerly Free Electrons)
Embedded Linux and Kernel engineering
http://bootlin.com