From: Alexander Hoogerhuis <alexh@ihatent.com>
To: Russell King <rmk@arm.linux.org.uk>
Cc: Andrew Morton <akpm@digeo.com>,
linux-kernel@vger.kernel.org, linux-mm@kvack.org
Subject: Re: 2.5.65-mm1
Date: 19 Mar 2003 01:14:13 +0100 [thread overview]
Message-ID: <873clkw6ui.fsf@lapper.ihatent.com> (raw)
In-Reply-To: <20030318160902.C21945@flint.arm.linux.org.uk>
Russell King <rmk@arm.linux.org.uk> writes:
> On Tue, Mar 18, 2003 at 04:51:11PM +0100, Alexander Hoogerhuis wrote:
> > Oh well, I've had one hang within 10 minutes of booting, came back and
> > the machine was unresponsive (mouse and keyboard under X, unable to
> > switch to console). Apart from that I've got two funnies in my boot
> > messages:
>
> Could you send the full bus information for all devices (lspci -vv),
> and the contents of /proc/iomem and /proc/ioports ?
>
> I don't believe there's anything in my PCI updates which should have
> changed the behaviour - they were touching mainly the scanning for
> devices, and the way we write resources back into the hardware. The
> latter rarely happens on x86, except for cardbus devices.
>
I'm not suspecting the PCI in particular for the PCIC-bits, only
making X and the Radeon work again. But here you are:
lapper root # lspci -vv
00:00.0 Host bridge: Intel Corp. 82845 845 (Brookdale) Chipset Host Bridge (rev 04)
Subsystem: Compaq Computer Corporation: Unknown device 004a
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at a0000000 (32-bit, prefetchable) [size=256M]
Capabilities: [e4] #09 [d104]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2,x4
Command: RQ=0 SBA+ AGP+ 64bit- FW- Rate=x4
00:01.0 PCI bridge: Intel Corp. 82845 845 (Brookdale) Chipset AGP Bridge (rev 04) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: 80300000-803fffff
Prefetchable memory behind bridge: 88000000-900fffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
00:1e.0 PCI bridge: Intel Corp. 82801BAM/CAM PCI Bridge (rev 42) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=03, sec-latency=32
I/O behind bridge: 00002000-00002fff
Memory behind bridge: 80000000-803fffff
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corp. 82801CAM ISA Bridge (LPC) (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface: Intel Corp. 82801CAM IDE U100 (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Compaq Computer Corporation: Unknown device 004a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at 4440 [size=16]
Region 5: Memory at 30000400 (32-bit, non-prefetchable) [size=1K]
00:1f.5 Multimedia audio controller: Intel Corp. 82801CA/CAM AC'97 Audio (rev 02)
Subsystem: Compaq Computer Corporation: Unknown device 004a
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 5
Region 0: I/O ports at 4000 [size=256]
Region 1: I/O ports at 4400 [size=64]
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M7 LW [Radeon Mobility 7500] (prog-if 00 [VGA])
Subsystem: Compaq Computer Corporation: Unknown device 004a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 88000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 3000 [size=256]
Region 2: Memory at 80380000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [58] AGP version 2.0
Status: RQ=47 SBA+ 64bit- FW- Rate=x1,x2,x4
Command: RQ=31 SBA+ AGP+ 64bit- FW- Rate=x4
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:04.0 Communication controller: Lucent Microelectronics LT WinModem (rev 02)
Subsystem: AMBIT Microsystem Corp.: Unknown device 0450
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (63000ns min, 3500ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at 80280000 (32-bit, non-prefetchable) [size=256]
Region 1: I/O ports at 2440 [size=8]
Region 2: I/O ports at 2000 [size=256]
Capabilities: [f8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=160mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:06.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus Controller (rev 02)
Subsystem: Compaq Computer Corporation: Unknown device 004a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 20
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 80080000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
Memory window 0: 30400000-307ff000 (prefetchable)
Memory window 1: 30800000-30bff000
I/O window 0: 00001400-000014ff
I/O window 1: 00001800-000018ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
02:08.0 Ethernet controller: Intel Corp. 82801CAM (ICH3) PRO/100 VE (LOM) Ethernet Controller (rev 42)
Subsystem: Compaq Computer Corporation: Unknown device 0093
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min, 14000ns max), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at 80100000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 2400 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
02:0e.0 USB Controller: NEC Corporation USB (rev 41) (prog-if 10 [OHCI])
Subsystem: Compaq Computer Corporation: Unknown device 004a
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (250ns min, 10500ns max), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at 80180000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:0e.1 USB Controller: NEC Corporation USB (rev 41) (prog-if 10 [OHCI])
Subsystem: Compaq Computer Corporation: Unknown device 004a
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (250ns min, 10500ns max), cache line size 08
Interrupt: pin B routed to IRQ 10
Region 0: Memory at 80200000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:0e.2 USB Controller: NEC Corporation USB 2.0 (rev 02) (prog-if 20 [EHCI])
Subsystem: Compaq Computer Corporation: Unknown device 004a
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 8500ns max), cache line size 20
Interrupt: pin C routed to IRQ 10
Region 0: Memory at 30000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
lapper root # cat /proc/iomem /proc/ioports
00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000f0000-000fffff : System ROM
00100000-2ffcffff : System RAM
00100000-002af453 : Kernel code
002af454-00364003 : Kernel data
2ffd0000-2fff0bff : reserved
2fff0c00-2fffbfff : ACPI Non-volatile Storage
2fffc000-2fffffff : reserved
30000000-300000ff : NEC Corporation USB 2.0
30000000-300000ff : ehci-hcd
30000400-300007ff : Intel Corp. 82801CAM IDE U100
30400000-307fffff : PCI CardBus #03
30800000-30bfffff : PCI CardBus #03
80080000-80080fff : Texas Instruments PCI1410 PC card Card
80100000-80100fff : Intel Corp. 82801CAM (ICH3) PRO/
80100000-80100fff : eepro100
80180000-80180fff : NEC Corporation USB
80180000-80180fff : ohci-hcd
80200000-80200fff : NEC Corporation USB (#2)
80200000-80200fff : ohci-hcd
80280000-802800ff : Lucent Microelectron LT WinModem
80300000-803fffff : PCI Bus #01
80380000-8038ffff : ATI Technologies Inc Radeon Mobility M7 L
88000000-900fffff : PCI Bus #01
88000000-8fffffff : ATI Technologies Inc Radeon Mobility M7 L
a0000000-afffffff : Intel Corp. 82845 845 (Brookdale
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
0376-0376 : ide1
0378-037a : parport0
037b-037f : parport0
03c0-03df : vga+
03f6-03f6 : ide0
0cf8-0cff : PCI conf1
1060-106f : i810 TCO
1400-14ff : PCI CardBus #03
1800-18ff : PCI CardBus #03
2000-20ff : Lucent Microelectron LT WinModem
2400-243f : Intel Corp. 82801CAM (ICH3) PRO/
2400-243f : eepro100
2440-2447 : Lucent Microelectron LT WinModem
3000-3fff : PCI Bus #01
3000-30ff : ATI Technologies Inc Radeon Mobility M7 L
4000-40ff : Intel Corp. 82801CA/CAM AC'97 Au
4000-40ff : Intel ICH3
4400-443f : Intel Corp. 82801CA/CAM AC'97 Au
4400-443f : Intel ICH3
4440-444f : Intel Corp. 82801CAM IDE U100
4440-4447 : ide0
4448-444f : ide1
lapper root #
mvh,
A
--
Alexander Hoogerhuis | alexh@ihatent.com
CCNP - CCDP - MCNE - CCSE | +47 908 21 485
"You have zero privacy anyway. Get over it." --Scott McNealy
WARNING: multiple messages have this Message-ID (diff)
From: Alexander Hoogerhuis <alexh@ihatent.com>
To: Russell King <rmk@arm.linux.org.uk>
Cc: Andrew Morton <akpm@digeo.com>,
linux-kernel@vger.kernel.org, linux-mm@kvack.org
Subject: Re: 2.5.65-mm1
Date: 19 Mar 2003 01:14:13 +0100 [thread overview]
Message-ID: <873clkw6ui.fsf@lapper.ihatent.com> (raw)
In-Reply-To: <20030318160902.C21945@flint.arm.linux.org.uk>
Russell King <rmk@arm.linux.org.uk> writes:
> On Tue, Mar 18, 2003 at 04:51:11PM +0100, Alexander Hoogerhuis wrote:
> > Oh well, I've had one hang within 10 minutes of booting, came back and
> > the machine was unresponsive (mouse and keyboard under X, unable to
> > switch to console). Apart from that I've got two funnies in my boot
> > messages:
>
> Could you send the full bus information for all devices (lspci -vv),
> and the contents of /proc/iomem and /proc/ioports ?
>
> I don't believe there's anything in my PCI updates which should have
> changed the behaviour - they were touching mainly the scanning for
> devices, and the way we write resources back into the hardware. The
> latter rarely happens on x86, except for cardbus devices.
>
I'm not suspecting the PCI in particular for the PCIC-bits, only
making X and the Radeon work again. But here you are:
lapper root # lspci -vv
00:00.0 Host bridge: Intel Corp. 82845 845 (Brookdale) Chipset Host Bridge (rev 04)
Subsystem: Compaq Computer Corporation: Unknown device 004a
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Region 0: Memory at a0000000 (32-bit, prefetchable) [size=256M]
Capabilities: [e4] #09 [d104]
Capabilities: [a0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW+ Rate=x1,x2,x4
Command: RQ=0 SBA+ AGP+ 64bit- FW- Rate=x4
00:01.0 PCI bridge: Intel Corp. 82845 845 (Brookdale) Chipset AGP Bridge (rev 04) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: 80300000-803fffff
Prefetchable memory behind bridge: 88000000-900fffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
00:1e.0 PCI bridge: Intel Corp. 82801BAM/CAM PCI Bridge (rev 42) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=03, sec-latency=32
I/O behind bridge: 00002000-00002fff
Memory behind bridge: 80000000-803fffff
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
00:1f.0 ISA bridge: Intel Corp. 82801CAM ISA Bridge (LPC) (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:1f.1 IDE interface: Intel Corp. 82801CAM IDE U100 (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Compaq Computer Corporation: Unknown device 004a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at <unassigned>
Region 1: I/O ports at <unassigned>
Region 2: I/O ports at <unassigned>
Region 3: I/O ports at <unassigned>
Region 4: I/O ports at 4440 [size=16]
Region 5: Memory at 30000400 (32-bit, non-prefetchable) [size=1K]
00:1f.5 Multimedia audio controller: Intel Corp. 82801CA/CAM AC'97 Audio (rev 02)
Subsystem: Compaq Computer Corporation: Unknown device 004a
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 5
Region 0: I/O ports at 4000 [size=256]
Region 1: I/O ports at 4400 [size=64]
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M7 LW [Radeon Mobility 7500] (prog-if 00 [VGA])
Subsystem: Compaq Computer Corporation: Unknown device 004a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min), cache line size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 88000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 3000 [size=256]
Region 2: Memory at 80380000 (32-bit, non-prefetchable) [size=64K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [58] AGP version 2.0
Status: RQ=47 SBA+ 64bit- FW- Rate=x1,x2,x4
Command: RQ=31 SBA+ AGP+ 64bit- FW- Rate=x4
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:04.0 Communication controller: Lucent Microelectronics LT WinModem (rev 02)
Subsystem: AMBIT Microsystem Corp.: Unknown device 0450
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (63000ns min, 3500ns max)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at 80280000 (32-bit, non-prefetchable) [size=256]
Region 1: I/O ports at 2440 [size=8]
Region 2: I/O ports at 2000 [size=256]
Capabilities: [f8] Power Management version 2
Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=160mA PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:06.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus Controller (rev 02)
Subsystem: Compaq Computer Corporation: Unknown device 004a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, cache line size 20
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 80080000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=02, secondary=03, subordinate=06, sec-latency=176
Memory window 0: 30400000-307ff000 (prefetchable)
Memory window 1: 30800000-30bff000
I/O window 0: 00001400-000014ff
I/O window 1: 00001800-000018ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
02:08.0 Ethernet controller: Intel Corp. 82801CAM (ICH3) PRO/100 VE (LOM) Ethernet Controller (rev 42)
Subsystem: Compaq Computer Corporation: Unknown device 0093
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 66 (2000ns min, 14000ns max), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at 80100000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at 2400 [size=64]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
02:0e.0 USB Controller: NEC Corporation USB (rev 41) (prog-if 10 [OHCI])
Subsystem: Compaq Computer Corporation: Unknown device 004a
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (250ns min, 10500ns max), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: Memory at 80180000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:0e.1 USB Controller: NEC Corporation USB (rev 41) (prog-if 10 [OHCI])
Subsystem: Compaq Computer Corporation: Unknown device 004a
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (250ns min, 10500ns max), cache line size 08
Interrupt: pin B routed to IRQ 10
Region 0: Memory at 80200000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:0e.2 USB Controller: NEC Corporation USB 2.0 (rev 02) (prog-if 20 [EHCI])
Subsystem: Compaq Computer Corporation: Unknown device 004a
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 8500ns max), cache line size 20
Interrupt: pin C routed to IRQ 10
Region 0: Memory at 30000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
lapper root # cat /proc/iomem /proc/ioports
00000000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : Video RAM area
000c0000-000c7fff : Video ROM
000f0000-000fffff : System ROM
00100000-2ffcffff : System RAM
00100000-002af453 : Kernel code
002af454-00364003 : Kernel data
2ffd0000-2fff0bff : reserved
2fff0c00-2fffbfff : ACPI Non-volatile Storage
2fffc000-2fffffff : reserved
30000000-300000ff : NEC Corporation USB 2.0
30000000-300000ff : ehci-hcd
30000400-300007ff : Intel Corp. 82801CAM IDE U100
30400000-307fffff : PCI CardBus #03
30800000-30bfffff : PCI CardBus #03
80080000-80080fff : Texas Instruments PCI1410 PC card Card
80100000-80100fff : Intel Corp. 82801CAM (ICH3) PRO/
80100000-80100fff : eepro100
80180000-80180fff : NEC Corporation USB
80180000-80180fff : ohci-hcd
80200000-80200fff : NEC Corporation USB (#2)
80200000-80200fff : ohci-hcd
80280000-802800ff : Lucent Microelectron LT WinModem
80300000-803fffff : PCI Bus #01
80380000-8038ffff : ATI Technologies Inc Radeon Mobility M7 L
88000000-900fffff : PCI Bus #01
88000000-8fffffff : ATI Technologies Inc Radeon Mobility M7 L
a0000000-afffffff : Intel Corp. 82845 845 (Brookdale
0000-001f : dma1
0020-003f : pic1
0040-005f : timer
0060-006f : keyboard
0080-008f : dma page reg
00a0-00bf : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
0376-0376 : ide1
0378-037a : parport0
037b-037f : parport0
03c0-03df : vga+
03f6-03f6 : ide0
0cf8-0cff : PCI conf1
1060-106f : i810 TCO
1400-14ff : PCI CardBus #03
1800-18ff : PCI CardBus #03
2000-20ff : Lucent Microelectron LT WinModem
2400-243f : Intel Corp. 82801CAM (ICH3) PRO/
2400-243f : eepro100
2440-2447 : Lucent Microelectron LT WinModem
3000-3fff : PCI Bus #01
3000-30ff : ATI Technologies Inc Radeon Mobility M7 L
4000-40ff : Intel Corp. 82801CA/CAM AC'97 Au
4000-40ff : Intel ICH3
4400-443f : Intel Corp. 82801CA/CAM AC'97 Au
4400-443f : Intel ICH3
4440-444f : Intel Corp. 82801CAM IDE U100
4440-4447 : ide0
4448-444f : ide1
lapper root #
mvh,
A
--
Alexander Hoogerhuis | alexh@ihatent.com
CCNP - CCDP - MCNE - CCSE | +47 908 21 485
"You have zero privacy anyway. Get over it." --Scott McNealy
--
To unsubscribe, send a message with 'unsubscribe linux-mm' in
the body to majordomo@kvack.org. For more info on Linux MM,
see: http://www.linux-mm.org/ .
Don't email: <a href=mailto:"aart@kvack.org">aart@kvack.org</a>
next prev parent reply other threads:[~2003-03-19 0:03 UTC|newest]
Thread overview: 27+ messages / expand[flat|nested] mbox.gz Atom feed top
2003-03-18 11:11 2.5.65-mm1 Andrew Morton
2003-03-18 11:11 ` 2.5.65-mm1 Andrew Morton
2003-03-18 13:15 ` 2.5.65-mm1 Helge Hafting
2003-03-18 13:15 ` 2.5.65-mm1 Helge Hafting
2003-03-18 13:29 ` 2.5.65-mm1 small nfs umount problem, also in 64-mm8 Helge Hafting
2003-03-18 13:56 ` Andreas Haumer
2003-03-18 15:08 ` 2.5.65-mm1 Alexander Hoogerhuis
2003-03-18 15:08 ` 2.5.65-mm1 Alexander Hoogerhuis
2003-03-18 15:51 ` 2.5.65-mm1 Alexander Hoogerhuis
2003-03-18 15:51 ` 2.5.65-mm1 Alexander Hoogerhuis
2003-03-18 16:09 ` 2.5.65-mm1 Russell King
2003-03-18 16:09 ` 2.5.65-mm1 Russell King
2003-03-19 0:14 ` Alexander Hoogerhuis [this message]
2003-03-19 0:14 ` 2.5.65-mm1 Alexander Hoogerhuis
2003-03-19 0:26 ` 2.5.65-mm1 Andrew Morton
2003-03-19 0:26 ` 2.5.65-mm1 Andrew Morton
2003-03-19 6:16 ` 2.5.65-mm1 Alexander Hoogerhuis
2003-03-19 6:16 ` 2.5.65-mm1 Alexander Hoogerhuis
2003-03-19 8:12 ` 2.5.65-mm1 Alexander Hoogerhuis
2003-03-19 8:12 ` 2.5.65-mm1 Alexander Hoogerhuis
2003-03-19 8:20 ` 2.5.65-mm1 Alexander Hoogerhuis
2003-03-19 8:20 ` 2.5.65-mm1 Alexander Hoogerhuis
2003-03-18 19:49 ` Re[2]: 2.5.65-mm1 Ruslan U. Zakirov
2003-03-18 21:33 ` 2.5.65-mm1 Adam Belay
2003-03-18 21:33 ` 2.5.65-mm1 Adam Belay
2003-03-18 21:40 ` 2.5.65-mm1 William Lee Irwin III
2003-03-18 21:40 ` 2.5.65-mm1 William Lee Irwin III
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=873clkw6ui.fsf@lapper.ihatent.com \
--to=alexh@ihatent.com \
--cc=akpm@digeo.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mm@kvack.org \
--cc=rmk@arm.linux.org.uk \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.