[PATCH v4 0/5] Add a new RTC driver for recent mvebu SoCs

[PATCH v4 0/5] Add a new RTC driver for recent mvebu SoCs

[Gregory CLEMENT]

Hi,

The Marvell Armada 38x SoCs contains an RTC which differs from the RTC
used in the other mvebu SoCs until now. This forth version of the
patch set adds support for this new IP and enable it in the Device
Tree of the Armada 38x SoC.

Thanks,

Gr?gory

Changelog

v3 -> v4:

- Formatted the device tree binding documentation in a better way
- Renamed the soc-int regmap to rtc-soc because this group of register
  was not only about the interrupt.
- Fixed the rtc_delayed_write function. I found the exact description
  of the WA to use, and the wait should really be after the write.

v2 -> v3:

- Fixed the reg-names description in the dt binding documentation
- Used the delayed version of the writel in everyplace.

v1 -> v2:

- Used reg-names to identify the registers in the device tree
- Changed the space into tab in the MAINTAINERS file
- Emphasized that the 5s wait was only needed between two consecutive
  writes
- Reduced the wait in the set_time function, 100ms were enough
- If no interrupt was available, then disable the alarm related
  functions
- Fixed the critical sections
- Updated the mvebu_v7_defconfig by enabling the new RTC support


Gregory CLEMENT (5):
  rtc: armada38x: Add the device tree binding documentation
  drivers/rtc/rtc-armada38x: Add a new RTC driver for recent mvebu SoCs
  MAINTAINERS: Add the RTC driver for the Armada38x
  ARM: mvebu: add Device Tree description of RTC on Armada 38x
  ARM: mvebu: enable Armada 38x RTC driver in mvebu_v7_defconfig

 .../devicetree/bindings/rtc/armada-380-rtc.txt     |  22 ++
 MAINTAINERS                                        |   1 +
 arch/arm/boot/dts/armada-38x.dtsi                  |   7 +
 arch/arm/configs/mvebu_v7_defconfig                |   1 +
 drivers/rtc/Kconfig                                |  10 +
 drivers/rtc/Makefile                               |   1 +
 drivers/rtc/rtc-armada38x.c                        | 320 +++++++++++++++++++++
 7 files changed, 362 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/rtc/armada-380-rtc.txt
 create mode 100644 drivers/rtc/rtc-armada38x.c

-- 
1.9.1

[PATCH v4 0/5] Add a new RTC driver for recent mvebu SoCs

[Gregory CLEMENT]

Hi,

The Marvell Armada 38x SoCs contains an RTC which differs from the RTC
used in the other mvebu SoCs until now. This forth version of the
patch set adds support for this new IP and enable it in the Device
Tree of the Armada 38x SoC.

Thanks,

Grégory

Changelog

v3 -> v4:

- Formatted the device tree binding documentation in a better way
- Renamed the soc-int regmap to rtc-soc because this group of register
  was not only about the interrupt.
- Fixed the rtc_delayed_write function. I found the exact description
  of the WA to use, and the wait should really be after the write.

v2 -> v3:

- Fixed the reg-names description in the dt binding documentation
- Used the delayed version of the writel in everyplace.

v1 -> v2:

- Used reg-names to identify the registers in the device tree
- Changed the space into tab in the MAINTAINERS file
- Emphasized that the 5s wait was only needed between two consecutive
  writes
- Reduced the wait in the set_time function, 100ms were enough
- If no interrupt was available, then disable the alarm related
  functions
- Fixed the critical sections
- Updated the mvebu_v7_defconfig by enabling the new RTC support


Gregory CLEMENT (5):
  rtc: armada38x: Add the device tree binding documentation
  drivers/rtc/rtc-armada38x: Add a new RTC driver for recent mvebu SoCs
  MAINTAINERS: Add the RTC driver for the Armada38x
  ARM: mvebu: add Device Tree description of RTC on Armada 38x
  ARM: mvebu: enable Armada 38x RTC driver in mvebu_v7_defconfig

 .../devicetree/bindings/rtc/armada-380-rtc.txt     |  22 ++
 MAINTAINERS                                        |   1 +
 arch/arm/boot/dts/armada-38x.dtsi                  |   7 +
 arch/arm/configs/mvebu_v7_defconfig                |   1 +
 drivers/rtc/Kconfig                                |  10 +
 drivers/rtc/Makefile                               |   1 +
 drivers/rtc/rtc-armada38x.c                        | 320 +++++++++++++++++++++
 7 files changed, 362 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/rtc/armada-380-rtc.txt
 create mode 100644 drivers/rtc/rtc-armada38x.c

-- 
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v4 1/5] rtc: armada38x: Add the device tree binding documentation

[Gregory CLEMENT]

The Armada 38x SoCs come with a new RTC which differs from the one
used in the other mvebu SoCs until now. This patch describes the
binding of this RTC.

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
---
 .../devicetree/bindings/rtc/armada-380-rtc.txt     | 22 ++++++++++++++++++++++
 1 file changed, 22 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/rtc/armada-380-rtc.txt

diff --git a/Documentation/devicetree/bindings/rtc/armada-380-rtc.txt b/Documentation/devicetree/bindings/rtc/armada-380-rtc.txt
new file mode 100644
index 000000000000..2eb9d4ee7dc0
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/armada-380-rtc.txt
@@ -0,0 +1,22 @@
+* Real Time Clock of the Armada 38x SoCs
+
+RTC controller for the Armada 38x SoCs
+
+Required properties:
+- compatible : Should be "marvell,armada-380-rtc"
+- reg: a list of base address and size pairs, one for each entry in
+  reg-names
+- reg names: should contain:
+  * "rtc" for the RTC registers
+  * "rtc-soc" for the SoC related registers and among them the one
+    related to the interrupt.
+- interrupts: IRQ line for the RTC.
+
+Example:
+
+rtc at a3800 {
+	compatible = "marvell,armada-380-rtc";
+	reg = <0xa3800 0x20>, <0x184a0 0x0c>;
+	reg-names = "rtc", "rtc-soc";
+	interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+};
-- 
1.9.1

[PATCH v4 1/5] rtc: armada38x: Add the device tree binding documentation

[Gregory CLEMENT]

The Armada 38x SoCs come with a new RTC which differs from the one
used in the other mvebu SoCs until now. This patch describes the
binding of this RTC.

Signed-off-by: Gregory CLEMENT <gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
---
 .../devicetree/bindings/rtc/armada-380-rtc.txt     | 22 ++++++++++++++++++++++
 1 file changed, 22 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/rtc/armada-380-rtc.txt

diff --git a/Documentation/devicetree/bindings/rtc/armada-380-rtc.txt b/Documentation/devicetree/bindings/rtc/armada-380-rtc.txt
new file mode 100644
index 000000000000..2eb9d4ee7dc0
--- /dev/null
+++ b/Documentation/devicetree/bindings/rtc/armada-380-rtc.txt
@@ -0,0 +1,22 @@
+* Real Time Clock of the Armada 38x SoCs
+
+RTC controller for the Armada 38x SoCs
+
+Required properties:
+- compatible : Should be "marvell,armada-380-rtc"
+- reg: a list of base address and size pairs, one for each entry in
+  reg-names
+- reg names: should contain:
+  * "rtc" for the RTC registers
+  * "rtc-soc" for the SoC related registers and among them the one
+    related to the interrupt.
+- interrupts: IRQ line for the RTC.
+
+Example:
+
+rtc@a3800 {
+	compatible = "marvell,armada-380-rtc";
+	reg = <0xa3800 0x20>, <0x184a0 0x0c>;
+	reg-names = "rtc", "rtc-soc";
+	interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+};
-- 
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v4 2/5] drivers/rtc/rtc-armada38x: Add a new RTC driver for recent mvebu SoCs

[Gregory CLEMENT]

The new mvebu SoCs come with a new RTC driver. This patch adds the
support for this new IP which is currently found in the Armada 38x
SoCs.

This RTC provides two alarms, but only the first one is used in the
driver. The RTC also allows using periodic interrupts.

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
---
 drivers/rtc/Kconfig         |  10 ++
 drivers/rtc/Makefile        |   1 +
 drivers/rtc/rtc-armada38x.c | 320 ++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 331 insertions(+)
 create mode 100644 drivers/rtc/rtc-armada38x.c

diff --git a/drivers/rtc/Kconfig b/drivers/rtc/Kconfig
index f15cddfeb897..de42ebd4b626 100644
--- a/drivers/rtc/Kconfig
+++ b/drivers/rtc/Kconfig
@@ -1269,6 +1269,16 @@ config RTC_DRV_MV
 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-mv.
 
+config RTC_DRV_ARMADA38X
+	tristate "Armada 38x Marvell SoC RTC"
+	depends on ARCH_MVEBU
+	help
+	  If you say yes here you will get support for the in-chip RTC
+	  that can be found in the Armada 38x Marvell's SoC device
+
+	  This driver can also be built as a module. If so, the module
+	  will be called armada38x-rtc.
+
 config RTC_DRV_PS3
 	tristate "PS3 RTC"
 	depends on PPC_PS3
diff --git a/drivers/rtc/Makefile b/drivers/rtc/Makefile
index c8ef3e1e6ccd..03fe5629c464 100644
--- a/drivers/rtc/Makefile
+++ b/drivers/rtc/Makefile
@@ -24,6 +24,7 @@ obj-$(CONFIG_RTC_DRV_88PM860X)  += rtc-88pm860x.o
 obj-$(CONFIG_RTC_DRV_88PM80X)	+= rtc-88pm80x.o
 obj-$(CONFIG_RTC_DRV_AB3100)	+= rtc-ab3100.o
 obj-$(CONFIG_RTC_DRV_AB8500)	+= rtc-ab8500.o
+obj-$(CONFIG_RTC_DRV_ARMADA38X)	+= rtc-armada38x.o
 obj-$(CONFIG_RTC_DRV_AS3722)	+= rtc-as3722.o
 obj-$(CONFIG_RTC_DRV_AT32AP700X)+= rtc-at32ap700x.o
 obj-$(CONFIG_RTC_DRV_AT91RM9200)+= rtc-at91rm9200.o
diff --git a/drivers/rtc/rtc-armada38x.c b/drivers/rtc/rtc-armada38x.c
new file mode 100644
index 000000000000..43e04af39e09
--- /dev/null
+++ b/drivers/rtc/rtc-armada38x.c
@@ -0,0 +1,320 @@
+/*
+ * RTC driver for the Armada 38x Marvell SoCs
+ *
+ * Copyright (C) 2015 Marvell
+ *
+ * Gregory Clement <gregory.clement@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ */
+
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/rtc.h>
+
+#define RTC_STATUS	    0x0
+#define RTC_STATUS_ALARM1	    BIT(0)
+#define RTC_STATUS_ALARM2	    BIT(1)
+#define RTC_IRQ1_CONF	    0x4
+#define RTC_IRQ1_AL_EN		    BIT(0)
+#define RTC_IRQ1_FREQ_EN	    BIT(1)
+#define RTC_IRQ1_FREQ_1HZ	    BIT(2)
+#define RTC_TIME	    0xC
+#define RTC_ALARM1	    0x10
+
+#define SOC_RTC_INTERRUPT   0x8
+#define SOC_RTC_ALARM1		BIT(0)
+#define SOC_RTC_ALARM2		BIT(1)
+#define SOC_RTC_ALARM1_MASK	BIT(2)
+#define SOC_RTC_ALARM2_MASK	BIT(3)
+
+struct armada38x_rtc {
+	struct rtc_device   *rtc_dev;
+	void __iomem	    *regs;
+	void __iomem	    *regs_soc;
+	spinlock_t	    lock;
+	int		    irq;
+};
+
+/*
+ * According to the datasheet, the OS should wait 5us after every
+ * register write to the RTC hard macro so that the required update
+ * can occur without holding off the system bus
+ */
+static void rtc_delayed_write(u32 val, struct armada38x_rtc *rtc, int offset)
+{
+	writel(val, rtc->regs + offset);
+	udelay(5);
+}
+
+static int armada38x_rtc_read_time(struct device *dev, struct rtc_time *tm)
+{
+	struct armada38x_rtc *rtc = dev_get_drvdata(dev);
+	unsigned long time, time_check, flags;
+
+	spin_lock_irqsave(&rtc->lock, flags);
+
+	time = readl(rtc->regs + RTC_TIME);
+	/*
+	 * WA for failing time set attempts. As stated in HW ERRATA if
+	 * more than one second between two time reads is detected
+	 * then read once again.
+	 */
+	time_check = readl(rtc->regs + RTC_TIME);
+	if ((time_check - time) > 1)
+		time_check = readl(rtc->regs + RTC_TIME);
+
+	spin_unlock_irqrestore(&rtc->lock, flags);
+
+	rtc_time_to_tm(time_check, tm);
+
+	return 0;
+}
+
+static int armada38x_rtc_set_time(struct device *dev, struct rtc_time *tm)
+{
+	struct armada38x_rtc *rtc = dev_get_drvdata(dev);
+	int ret = 0;
+	unsigned long time, flags;
+
+	ret = rtc_tm_to_time(tm, &time);
+
+	if (ret)
+		goto out;
+	/*
+	 * Setting the RTC time not always succeeds. According to the
+	 * errata we need to first write on the status register and
+	 * then wait for 100ms before writing to the time register to be
+	 * sure that the data will be taken into account.
+	 */
+	spin_lock_irqsave(&rtc->lock, flags);
+
+	rtc_delayed_write(0, rtc, RTC_STATUS);
+
+	spin_unlock_irqrestore(&rtc->lock, flags);
+
+	msleep(100);
+
+	spin_lock_irqsave(&rtc->lock, flags);
+
+	rtc_delayed_write(time, rtc, RTC_TIME);
+
+	spin_unlock_irqrestore(&rtc->lock, flags);
+out:
+	return ret;
+}
+
+static int armada38x_rtc_read_alarm(struct device *dev, struct rtc_wkalrm *alrm)
+{
+	struct armada38x_rtc *rtc = dev_get_drvdata(dev);
+	unsigned long time, flags;
+	u32 val;
+
+	spin_lock_irqsave(&rtc->lock, flags);
+
+	time = readl(rtc->regs + RTC_ALARM1);
+	val = readl(rtc->regs + RTC_IRQ1_CONF) & RTC_IRQ1_AL_EN;
+
+	spin_unlock_irqrestore(&rtc->lock, flags);
+
+	alrm->enabled = val ? 1 : 0;
+	rtc_time_to_tm(time,  &alrm->time);
+
+	return 0;
+}
+
+static int armada38x_rtc_set_alarm(struct device *dev, struct rtc_wkalrm *alrm)
+{
+	struct armada38x_rtc *rtc = dev_get_drvdata(dev);
+	unsigned long time, flags;
+	int ret = 0;
+	u32 val;
+
+	ret = rtc_tm_to_time(&alrm->time, &time);
+
+	if (ret)
+		goto out;
+
+	spin_lock_irqsave(&rtc->lock, flags);
+
+	rtc_delayed_write(time, rtc, RTC_ALARM1);
+
+	if (alrm->enabled) {
+			rtc_delayed_write(RTC_IRQ1_AL_EN, rtc, RTC_IRQ1_CONF);
+			val = readl(rtc->regs_soc + SOC_RTC_INTERRUPT);
+			writel(val | SOC_RTC_ALARM1_MASK,
+			       rtc->regs_soc + SOC_RTC_INTERRUPT);
+	}
+
+	spin_unlock_irqrestore(&rtc->lock, flags);
+
+out:
+	return ret;
+}
+
+static int armada38x_rtc_alarm_irq_enable(struct device *dev,
+					 unsigned int enabled)
+{
+	struct armada38x_rtc *rtc = dev_get_drvdata(dev);
+	unsigned long flags;
+
+	spin_lock_irqsave(&rtc->lock, flags);
+
+	if (enabled)
+		rtc_delayed_write(RTC_IRQ1_AL_EN, rtc, RTC_IRQ1_CONF);
+	else
+		rtc_delayed_write(0, rtc, RTC_IRQ1_CONF);
+
+	spin_unlock_irqrestore(&rtc->lock, flags);
+
+	return 0;
+}
+
+static irqreturn_t armada38x_rtc_alarm_irq(int irq, void *data)
+{
+	struct armada38x_rtc *rtc = data;
+	u32 val;
+	int event = RTC_IRQF | RTC_AF;
+
+	dev_dbg(&rtc->rtc_dev->dev, "%s:irq(%d)\n", __func__, irq);
+
+	spin_lock(&rtc->lock);
+
+	val = readl(rtc->regs_soc + SOC_RTC_INTERRUPT);
+
+	writel(val & ~SOC_RTC_ALARM1, rtc->regs_soc + SOC_RTC_INTERRUPT);
+	val = readl(rtc->regs + RTC_IRQ1_CONF);
+	/* disable all the interrupts for alarm 1 */
+	rtc_delayed_write(0, rtc, RTC_IRQ1_CONF);
+	/* Ack the event */
+	rtc_delayed_write(RTC_STATUS_ALARM1, rtc, RTC_STATUS);
+
+	spin_unlock(&rtc->lock);
+
+	if (val & RTC_IRQ1_FREQ_EN) {
+		if (val & RTC_IRQ1_FREQ_1HZ)
+			event |= RTC_UF;
+		else
+			event |= RTC_PF;
+	}
+
+	rtc_update_irq(rtc->rtc_dev, 1, event);
+
+	return IRQ_HANDLED;
+}
+
+static struct rtc_class_ops armada38x_rtc_ops = {
+	.read_time = armada38x_rtc_read_time,
+	.set_time = armada38x_rtc_set_time,
+	.read_alarm = armada38x_rtc_read_alarm,
+	.set_alarm = armada38x_rtc_set_alarm,
+	.alarm_irq_enable = armada38x_rtc_alarm_irq_enable,
+};
+
+static __init int armada38x_rtc_probe(struct platform_device *pdev)
+{
+	struct resource *res;
+	struct armada38x_rtc *rtc;
+	int ret;
+
+	rtc = devm_kzalloc(&pdev->dev, sizeof(struct armada38x_rtc),
+			    GFP_KERNEL);
+	if (!rtc)
+		return -ENOMEM;
+
+	spin_lock_init(&rtc->lock);
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "rtc");
+	rtc->regs = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(rtc->regs))
+		return PTR_ERR(rtc->regs);
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "rtc-soc");
+	rtc->regs_soc = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(rtc->regs_soc))
+		return PTR_ERR(rtc->regs_soc);
+
+	rtc->irq = platform_get_irq(pdev, 0);
+
+	if (rtc->irq < 0) {
+		dev_err(&pdev->dev, "no irq\n");
+		return rtc->irq;
+	}
+	if (devm_request_irq(&pdev->dev, rtc->irq, armada38x_rtc_alarm_irq,
+				0, pdev->name, rtc) < 0) {
+		dev_warn(&pdev->dev, "Interrupt not available.\n");
+		rtc->irq = -1;
+		/*
+		 * If there is no interrupt available then we can't
+		 * use the alarm
+		 */
+		armada38x_rtc_ops.set_alarm = NULL;
+		armada38x_rtc_ops.alarm_irq_enable = NULL;
+	}
+	platform_set_drvdata(pdev, rtc);
+	if (rtc->irq != -1)
+		device_init_wakeup(&pdev->dev, 1);
+
+	rtc->rtc_dev = devm_rtc_device_register(&pdev->dev, pdev->name,
+					&armada38x_rtc_ops, THIS_MODULE);
+	if (IS_ERR(rtc->rtc_dev)) {
+		ret = PTR_ERR(rtc->rtc_dev);
+		dev_err(&pdev->dev, "Failed to register RTC device: %d\n", ret);
+		return ret;
+	}
+	return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int armada38x_rtc_suspend(struct device *dev)
+{
+	if (device_may_wakeup(dev)) {
+		struct armada38x_rtc *rtc = dev_get_drvdata(dev);
+
+		return enable_irq_wake(rtc->irq);
+	}
+
+	return 0;
+}
+
+static int armada38x_rtc_resume(struct device *dev)
+{
+	if (device_may_wakeup(dev)) {
+		struct armada38x_rtc *rtc = dev_get_drvdata(dev);
+
+		return disable_irq_wake(rtc->irq);
+	}
+
+	return 0;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(armada38x_rtc_pm_ops,
+			 armada38x_rtc_suspend, armada38x_rtc_resume);
+
+#ifdef CONFIG_OF
+static const struct of_device_id armada38x_rtc_of_match_table[] = {
+	{ .compatible = "marvell,armada-380-rtc", },
+	{}
+};
+#endif
+
+static struct platform_driver armada38x_rtc_driver = {
+	.driver		= {
+		.name	= "armada38x-rtc",
+		.pm	= &armada38x_rtc_pm_ops,
+		.of_match_table = of_match_ptr(armada38x_rtc_of_match_table),
+	},
+};
+
+module_platform_driver_probe(armada38x_rtc_driver, armada38x_rtc_probe);
+
+MODULE_DESCRIPTION("Marvell Armada 38x RTC driver");
+MODULE_AUTHOR("Gregory CLEMENT <gregory.clement@free-electrons.com>");
+MODULE_LICENSE("GPL");
-- 
1.9.1

[PATCH v4 2/5] drivers/rtc/rtc-armada38x: Add a new RTC driver for recent mvebu SoCs

[Gregory CLEMENT]

The new mvebu SoCs come with a new RTC driver. This patch adds the
support for this new IP which is currently found in the Armada 38x
SoCs.

This RTC provides two alarms, but only the first one is used in the
driver. The RTC also allows using periodic interrupts.

Signed-off-by: Gregory CLEMENT <gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
---
 drivers/rtc/Kconfig         |  10 ++
 drivers/rtc/Makefile        |   1 +
 drivers/rtc/rtc-armada38x.c | 320 ++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 331 insertions(+)
 create mode 100644 drivers/rtc/rtc-armada38x.c

diff --git a/drivers/rtc/Kconfig b/drivers/rtc/Kconfig
index f15cddfeb897..de42ebd4b626 100644
--- a/drivers/rtc/Kconfig
+++ b/drivers/rtc/Kconfig
@@ -1269,6 +1269,16 @@ config RTC_DRV_MV
 	  This driver can also be built as a module. If so, the module
 	  will be called rtc-mv.
 
+config RTC_DRV_ARMADA38X
+	tristate "Armada 38x Marvell SoC RTC"
+	depends on ARCH_MVEBU
+	help
+	  If you say yes here you will get support for the in-chip RTC
+	  that can be found in the Armada 38x Marvell's SoC device
+
+	  This driver can also be built as a module. If so, the module
+	  will be called armada38x-rtc.
+
 config RTC_DRV_PS3
 	tristate "PS3 RTC"
 	depends on PPC_PS3
diff --git a/drivers/rtc/Makefile b/drivers/rtc/Makefile
index c8ef3e1e6ccd..03fe5629c464 100644
--- a/drivers/rtc/Makefile
+++ b/drivers/rtc/Makefile
@@ -24,6 +24,7 @@ obj-$(CONFIG_RTC_DRV_88PM860X)  += rtc-88pm860x.o
 obj-$(CONFIG_RTC_DRV_88PM80X)	+= rtc-88pm80x.o
 obj-$(CONFIG_RTC_DRV_AB3100)	+= rtc-ab3100.o
 obj-$(CONFIG_RTC_DRV_AB8500)	+= rtc-ab8500.o
+obj-$(CONFIG_RTC_DRV_ARMADA38X)	+= rtc-armada38x.o
 obj-$(CONFIG_RTC_DRV_AS3722)	+= rtc-as3722.o
 obj-$(CONFIG_RTC_DRV_AT32AP700X)+= rtc-at32ap700x.o
 obj-$(CONFIG_RTC_DRV_AT91RM9200)+= rtc-at91rm9200.o
diff --git a/drivers/rtc/rtc-armada38x.c b/drivers/rtc/rtc-armada38x.c
new file mode 100644
index 000000000000..43e04af39e09
--- /dev/null
+++ b/drivers/rtc/rtc-armada38x.c
@@ -0,0 +1,320 @@
+/*
+ * RTC driver for the Armada 38x Marvell SoCs
+ *
+ * Copyright (C) 2015 Marvell
+ *
+ * Gregory Clement <gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ */
+
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/rtc.h>
+
+#define RTC_STATUS	    0x0
+#define RTC_STATUS_ALARM1	    BIT(0)
+#define RTC_STATUS_ALARM2	    BIT(1)
+#define RTC_IRQ1_CONF	    0x4
+#define RTC_IRQ1_AL_EN		    BIT(0)
+#define RTC_IRQ1_FREQ_EN	    BIT(1)
+#define RTC_IRQ1_FREQ_1HZ	    BIT(2)
+#define RTC_TIME	    0xC
+#define RTC_ALARM1	    0x10
+
+#define SOC_RTC_INTERRUPT   0x8
+#define SOC_RTC_ALARM1		BIT(0)
+#define SOC_RTC_ALARM2		BIT(1)
+#define SOC_RTC_ALARM1_MASK	BIT(2)
+#define SOC_RTC_ALARM2_MASK	BIT(3)
+
+struct armada38x_rtc {
+	struct rtc_device   *rtc_dev;
+	void __iomem	    *regs;
+	void __iomem	    *regs_soc;
+	spinlock_t	    lock;
+	int		    irq;
+};
+
+/*
+ * According to the datasheet, the OS should wait 5us after every
+ * register write to the RTC hard macro so that the required update
+ * can occur without holding off the system bus
+ */
+static void rtc_delayed_write(u32 val, struct armada38x_rtc *rtc, int offset)
+{
+	writel(val, rtc->regs + offset);
+	udelay(5);
+}
+
+static int armada38x_rtc_read_time(struct device *dev, struct rtc_time *tm)
+{
+	struct armada38x_rtc *rtc = dev_get_drvdata(dev);
+	unsigned long time, time_check, flags;
+
+	spin_lock_irqsave(&rtc->lock, flags);
+
+	time = readl(rtc->regs + RTC_TIME);
+	/*
+	 * WA for failing time set attempts. As stated in HW ERRATA if
+	 * more than one second between two time reads is detected
+	 * then read once again.
+	 */
+	time_check = readl(rtc->regs + RTC_TIME);
+	if ((time_check - time) > 1)
+		time_check = readl(rtc->regs + RTC_TIME);
+
+	spin_unlock_irqrestore(&rtc->lock, flags);
+
+	rtc_time_to_tm(time_check, tm);
+
+	return 0;
+}
+
+static int armada38x_rtc_set_time(struct device *dev, struct rtc_time *tm)
+{
+	struct armada38x_rtc *rtc = dev_get_drvdata(dev);
+	int ret = 0;
+	unsigned long time, flags;
+
+	ret = rtc_tm_to_time(tm, &time);
+
+	if (ret)
+		goto out;
+	/*
+	 * Setting the RTC time not always succeeds. According to the
+	 * errata we need to first write on the status register and
+	 * then wait for 100ms before writing to the time register to be
+	 * sure that the data will be taken into account.
+	 */
+	spin_lock_irqsave(&rtc->lock, flags);
+
+	rtc_delayed_write(0, rtc, RTC_STATUS);
+
+	spin_unlock_irqrestore(&rtc->lock, flags);
+
+	msleep(100);
+
+	spin_lock_irqsave(&rtc->lock, flags);
+
+	rtc_delayed_write(time, rtc, RTC_TIME);
+
+	spin_unlock_irqrestore(&rtc->lock, flags);
+out:
+	return ret;
+}
+
+static int armada38x_rtc_read_alarm(struct device *dev, struct rtc_wkalrm *alrm)
+{
+	struct armada38x_rtc *rtc = dev_get_drvdata(dev);
+	unsigned long time, flags;
+	u32 val;
+
+	spin_lock_irqsave(&rtc->lock, flags);
+
+	time = readl(rtc->regs + RTC_ALARM1);
+	val = readl(rtc->regs + RTC_IRQ1_CONF) & RTC_IRQ1_AL_EN;
+
+	spin_unlock_irqrestore(&rtc->lock, flags);
+
+	alrm->enabled = val ? 1 : 0;
+	rtc_time_to_tm(time,  &alrm->time);
+
+	return 0;
+}
+
+static int armada38x_rtc_set_alarm(struct device *dev, struct rtc_wkalrm *alrm)
+{
+	struct armada38x_rtc *rtc = dev_get_drvdata(dev);
+	unsigned long time, flags;
+	int ret = 0;
+	u32 val;
+
+	ret = rtc_tm_to_time(&alrm->time, &time);
+
+	if (ret)
+		goto out;
+
+	spin_lock_irqsave(&rtc->lock, flags);
+
+	rtc_delayed_write(time, rtc, RTC_ALARM1);
+
+	if (alrm->enabled) {
+			rtc_delayed_write(RTC_IRQ1_AL_EN, rtc, RTC_IRQ1_CONF);
+			val = readl(rtc->regs_soc + SOC_RTC_INTERRUPT);
+			writel(val | SOC_RTC_ALARM1_MASK,
+			       rtc->regs_soc + SOC_RTC_INTERRUPT);
+	}
+
+	spin_unlock_irqrestore(&rtc->lock, flags);
+
+out:
+	return ret;
+}
+
+static int armada38x_rtc_alarm_irq_enable(struct device *dev,
+					 unsigned int enabled)
+{
+	struct armada38x_rtc *rtc = dev_get_drvdata(dev);
+	unsigned long flags;
+
+	spin_lock_irqsave(&rtc->lock, flags);
+
+	if (enabled)
+		rtc_delayed_write(RTC_IRQ1_AL_EN, rtc, RTC_IRQ1_CONF);
+	else
+		rtc_delayed_write(0, rtc, RTC_IRQ1_CONF);
+
+	spin_unlock_irqrestore(&rtc->lock, flags);
+
+	return 0;
+}
+
+static irqreturn_t armada38x_rtc_alarm_irq(int irq, void *data)
+{
+	struct armada38x_rtc *rtc = data;
+	u32 val;
+	int event = RTC_IRQF | RTC_AF;
+
+	dev_dbg(&rtc->rtc_dev->dev, "%s:irq(%d)\n", __func__, irq);
+
+	spin_lock(&rtc->lock);
+
+	val = readl(rtc->regs_soc + SOC_RTC_INTERRUPT);
+
+	writel(val & ~SOC_RTC_ALARM1, rtc->regs_soc + SOC_RTC_INTERRUPT);
+	val = readl(rtc->regs + RTC_IRQ1_CONF);
+	/* disable all the interrupts for alarm 1 */
+	rtc_delayed_write(0, rtc, RTC_IRQ1_CONF);
+	/* Ack the event */
+	rtc_delayed_write(RTC_STATUS_ALARM1, rtc, RTC_STATUS);
+
+	spin_unlock(&rtc->lock);
+
+	if (val & RTC_IRQ1_FREQ_EN) {
+		if (val & RTC_IRQ1_FREQ_1HZ)
+			event |= RTC_UF;
+		else
+			event |= RTC_PF;
+	}
+
+	rtc_update_irq(rtc->rtc_dev, 1, event);
+
+	return IRQ_HANDLED;
+}
+
+static struct rtc_class_ops armada38x_rtc_ops = {
+	.read_time = armada38x_rtc_read_time,
+	.set_time = armada38x_rtc_set_time,
+	.read_alarm = armada38x_rtc_read_alarm,
+	.set_alarm = armada38x_rtc_set_alarm,
+	.alarm_irq_enable = armada38x_rtc_alarm_irq_enable,
+};
+
+static __init int armada38x_rtc_probe(struct platform_device *pdev)
+{
+	struct resource *res;
+	struct armada38x_rtc *rtc;
+	int ret;
+
+	rtc = devm_kzalloc(&pdev->dev, sizeof(struct armada38x_rtc),
+			    GFP_KERNEL);
+	if (!rtc)
+		return -ENOMEM;
+
+	spin_lock_init(&rtc->lock);
+
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "rtc");
+	rtc->regs = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(rtc->regs))
+		return PTR_ERR(rtc->regs);
+	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "rtc-soc");
+	rtc->regs_soc = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(rtc->regs_soc))
+		return PTR_ERR(rtc->regs_soc);
+
+	rtc->irq = platform_get_irq(pdev, 0);
+
+	if (rtc->irq < 0) {
+		dev_err(&pdev->dev, "no irq\n");
+		return rtc->irq;
+	}
+	if (devm_request_irq(&pdev->dev, rtc->irq, armada38x_rtc_alarm_irq,
+				0, pdev->name, rtc) < 0) {
+		dev_warn(&pdev->dev, "Interrupt not available.\n");
+		rtc->irq = -1;
+		/*
+		 * If there is no interrupt available then we can't
+		 * use the alarm
+		 */
+		armada38x_rtc_ops.set_alarm = NULL;
+		armada38x_rtc_ops.alarm_irq_enable = NULL;
+	}
+	platform_set_drvdata(pdev, rtc);
+	if (rtc->irq != -1)
+		device_init_wakeup(&pdev->dev, 1);
+
+	rtc->rtc_dev = devm_rtc_device_register(&pdev->dev, pdev->name,
+					&armada38x_rtc_ops, THIS_MODULE);
+	if (IS_ERR(rtc->rtc_dev)) {
+		ret = PTR_ERR(rtc->rtc_dev);
+		dev_err(&pdev->dev, "Failed to register RTC device: %d\n", ret);
+		return ret;
+	}
+	return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int armada38x_rtc_suspend(struct device *dev)
+{
+	if (device_may_wakeup(dev)) {
+		struct armada38x_rtc *rtc = dev_get_drvdata(dev);
+
+		return enable_irq_wake(rtc->irq);
+	}
+
+	return 0;
+}
+
+static int armada38x_rtc_resume(struct device *dev)
+{
+	if (device_may_wakeup(dev)) {
+		struct armada38x_rtc *rtc = dev_get_drvdata(dev);
+
+		return disable_irq_wake(rtc->irq);
+	}
+
+	return 0;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(armada38x_rtc_pm_ops,
+			 armada38x_rtc_suspend, armada38x_rtc_resume);
+
+#ifdef CONFIG_OF
+static const struct of_device_id armada38x_rtc_of_match_table[] = {
+	{ .compatible = "marvell,armada-380-rtc", },
+	{}
+};
+#endif
+
+static struct platform_driver armada38x_rtc_driver = {
+	.driver		= {
+		.name	= "armada38x-rtc",
+		.pm	= &armada38x_rtc_pm_ops,
+		.of_match_table = of_match_ptr(armada38x_rtc_of_match_table),
+	},
+};
+
+module_platform_driver_probe(armada38x_rtc_driver, armada38x_rtc_probe);
+
+MODULE_DESCRIPTION("Marvell Armada 38x RTC driver");
+MODULE_AUTHOR("Gregory CLEMENT <gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>");
+MODULE_LICENSE("GPL");
-- 
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v4 2/5] drivers/rtc/rtc-armada38x: Add a new RTC driver for recent mvebu SoCs

[Arnaud Ebalard]

Hi Gregory,

Gregory CLEMENT <gregory.clement@free-electrons.com> writes:

> The new mvebu SoCs come with a new RTC driver. This patch adds the
> support for this new IP which is currently found in the Armada 38x
> SoCs.
>
> This RTC provides two alarms, but only the first one is used in the
> driver. The RTC also allows using periodic interrupts.
>
> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
> ---
>  drivers/rtc/Kconfig         |  10 ++
>  drivers/rtc/Makefile        |   1 +
>  drivers/rtc/rtc-armada38x.c | 320 ++++++++++++++++++++++++++++++++++++++++++++
>  3 files changed, 331 insertions(+)
>  create mode 100644 drivers/rtc/rtc-armada38x.c

FWIW:

Reviewed-by: Arnaud Ebalard <arno@natisbad.org>

Cheers,

a+

Re: [PATCH v4 2/5] drivers/rtc/rtc-armada38x: Add a new RTC driver for recent mvebu SoCs

[Arnaud Ebalard]

Hi Gregory,

Gregory CLEMENT <gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org> writes:

> The new mvebu SoCs come with a new RTC driver. This patch adds the
> support for this new IP which is currently found in the Armada 38x
> SoCs.
>
> This RTC provides two alarms, but only the first one is used in the
> driver. The RTC also allows using periodic interrupts.
>
> Signed-off-by: Gregory CLEMENT <gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
> ---
>  drivers/rtc/Kconfig         |  10 ++
>  drivers/rtc/Makefile        |   1 +
>  drivers/rtc/rtc-armada38x.c | 320 ++++++++++++++++++++++++++++++++++++++++++++
>  3 files changed, 331 insertions(+)
>  create mode 100644 drivers/rtc/rtc-armada38x.c

FWIW:

Reviewed-by: Arnaud Ebalard <arno-LkuqDEemtHBg9hUCZPvPmw@public.gmane.org>

Cheers,

a+
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v4 3/5] MAINTAINERS: Add the RTC driver for the Armada38x

[Gregory CLEMENT]

Put it in the mvebu entry.

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
---
 MAINTAINERS | 1 +
 1 file changed, 1 insertion(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index ddb9ac8d32b3..393f158a64e8 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1157,6 +1157,7 @@ M:	Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
 L:	linux-arm-kernel at lists.infradead.org (moderated for non-subscribers)
 S:	Maintained
 F:	arch/arm/mach-mvebu/
+F:	drivers/rtc/armada38x-rtc
 
 ARM/Marvell Berlin SoC support
 M:	Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
-- 
1.9.1

[PATCH v4 3/5] MAINTAINERS: Add the RTC driver for the Armada38x

[Gregory CLEMENT]

Put it in the mvebu entry.

Signed-off-by: Gregory CLEMENT <gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
---
 MAINTAINERS | 1 +
 1 file changed, 1 insertion(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index ddb9ac8d32b3..393f158a64e8 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1157,6 +1157,7 @@ M:	Sebastian Hesselbarth <sebastian.hesselbarth-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
 L:	linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org (moderated for non-subscribers)
 S:	Maintained
 F:	arch/arm/mach-mvebu/
+F:	drivers/rtc/armada38x-rtc
 
 ARM/Marvell Berlin SoC support
 M:	Sebastian Hesselbarth <sebastian.hesselbarth-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
-- 
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v4 4/5] ARM: mvebu: add Device Tree description of RTC on Armada 38x

[Gregory CLEMENT]

The Marvell Armada 38x SoCs contains an RTC which differs from the RTC
used in the other mvebu SoCs until now. This commit adds the Device
Tree description of this interface at the SoC level.

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
---
 arch/arm/boot/dts/armada-38x.dtsi | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/arm/boot/dts/armada-38x.dtsi b/arch/arm/boot/dts/armada-38x.dtsi
index 04fe80d101f8..79c4acf186e2 100644
--- a/arch/arm/boot/dts/armada-38x.dtsi
+++ b/arch/arm/boot/dts/armada-38x.dtsi
@@ -466,6 +466,13 @@
 				clocks = <&gateclk 4>;
 			};
 
+			rtc at a3800 {
+				compatible = "marvell,armada-380-rtc";
+				reg = <0xa3800 0x20>, <0x184a0 0x0c>;
+				reg-names = "rtc", "rtc-soc";
+				interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
 			sata at a8000 {
 				compatible = "marvell,armada-380-ahci";
 				reg = <0xa8000 0x2000>;
-- 
1.9.1

[PATCH v4 4/5] ARM: mvebu: add Device Tree description of RTC on Armada 38x

[Gregory CLEMENT]

The Marvell Armada 38x SoCs contains an RTC which differs from the RTC
used in the other mvebu SoCs until now. This commit adds the Device
Tree description of this interface at the SoC level.

Signed-off-by: Gregory CLEMENT <gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
---
 arch/arm/boot/dts/armada-38x.dtsi | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/arm/boot/dts/armada-38x.dtsi b/arch/arm/boot/dts/armada-38x.dtsi
index 04fe80d101f8..79c4acf186e2 100644
--- a/arch/arm/boot/dts/armada-38x.dtsi
+++ b/arch/arm/boot/dts/armada-38x.dtsi
@@ -466,6 +466,13 @@
 				clocks = <&gateclk 4>;
 			};
 
+			rtc@a3800 {
+				compatible = "marvell,armada-380-rtc";
+				reg = <0xa3800 0x20>, <0x184a0 0x0c>;
+				reg-names = "rtc", "rtc-soc";
+				interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+			};
+
 			sata@a8000 {
 				compatible = "marvell,armada-380-ahci";
 				reg = <0xa8000 0x2000>;
-- 
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v4 5/5] ARM: mvebu: enable Armada 38x RTC driver in mvebu_v7_defconfig

[Gregory CLEMENT]

Now that the Armada 38x RTC driver has been pushed, let's enable it in
mvebu_v7_defconfig.

Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
---
 arch/arm/configs/mvebu_v7_defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/configs/mvebu_v7_defconfig b/arch/arm/configs/mvebu_v7_defconfig
index 627accea72fb..2400b9f52403 100644
--- a/arch/arm/configs/mvebu_v7_defconfig
+++ b/arch/arm/configs/mvebu_v7_defconfig
@@ -112,6 +112,7 @@ CONFIG_LEDS_TRIGGER_HEARTBEAT=y
 CONFIG_RTC_CLASS=y
 CONFIG_RTC_DRV_S35390A=y
 CONFIG_RTC_DRV_MV=y
+CONFIG_RTC_DRV_ARMADA38X=y
 CONFIG_DMADEVICES=y
 CONFIG_MV_XOR=y
 # CONFIG_IOMMU_SUPPORT is not set
-- 
1.9.1

[PATCH v4 5/5] ARM: mvebu: enable Armada 38x RTC driver in mvebu_v7_defconfig

[Gregory CLEMENT]

Now that the Armada 38x RTC driver has been pushed, let's enable it in
mvebu_v7_defconfig.

Signed-off-by: Gregory CLEMENT <gregory.clement-wi1+55ScJUtKEb57/3fJTNBPR1lH4CV8@public.gmane.org>
---
 arch/arm/configs/mvebu_v7_defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm/configs/mvebu_v7_defconfig b/arch/arm/configs/mvebu_v7_defconfig
index 627accea72fb..2400b9f52403 100644
--- a/arch/arm/configs/mvebu_v7_defconfig
+++ b/arch/arm/configs/mvebu_v7_defconfig
@@ -112,6 +112,7 @@ CONFIG_LEDS_TRIGGER_HEARTBEAT=y
 CONFIG_RTC_CLASS=y
 CONFIG_RTC_DRV_S35390A=y
 CONFIG_RTC_DRV_MV=y
+CONFIG_RTC_DRV_ARMADA38X=y
 CONFIG_DMADEVICES=y
 CONFIG_MV_XOR=y
 # CONFIG_IOMMU_SUPPORT is not set
-- 
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v4 0/5] Add a new RTC driver for recent mvebu SoCs

[Gregory CLEMENT]

Hi,


On 15/01/2015 18:23, Gregory CLEMENT wrote:
> Hi,
> 
> The Marvell Armada 38x SoCs contains an RTC which differs from the RTC
> used in the other mvebu SoCs until now. This forth version of the
> patch set adds support for this new IP and enable it in the Device
> Tree of the Armada 38x SoC.

This last version of this series have been sent 3 weeks ago. Is there
an hope to be merged in 3.20 ?

Should they go through via Andrew Morten's tree ?


Thanks,

Gregory


> 
> Thanks,
> 
> Gr?gory
> 
> Changelog
> 
> v3 -> v4:
> 
> - Formatted the device tree binding documentation in a better way
> - Renamed the soc-int regmap to rtc-soc because this group of register
>   was not only about the interrupt.
> - Fixed the rtc_delayed_write function. I found the exact description
>   of the WA to use, and the wait should really be after the write.
> 
> v2 -> v3:
> 
> - Fixed the reg-names description in the dt binding documentation
> - Used the delayed version of the writel in everyplace.
> 
> v1 -> v2:
> 
> - Used reg-names to identify the registers in the device tree
> - Changed the space into tab in the MAINTAINERS file
> - Emphasized that the 5s wait was only needed between two consecutive
>   writes
> - Reduced the wait in the set_time function, 100ms were enough
> - If no interrupt was available, then disable the alarm related
>   functions
> - Fixed the critical sections
> - Updated the mvebu_v7_defconfig by enabling the new RTC support
> 
> 
> Gregory CLEMENT (5):
>   rtc: armada38x: Add the device tree binding documentation
>   drivers/rtc/rtc-armada38x: Add a new RTC driver for recent mvebu SoCs
>   MAINTAINERS: Add the RTC driver for the Armada38x
>   ARM: mvebu: add Device Tree description of RTC on Armada 38x
>   ARM: mvebu: enable Armada 38x RTC driver in mvebu_v7_defconfig
> 
>  .../devicetree/bindings/rtc/armada-380-rtc.txt     |  22 ++
>  MAINTAINERS                                        |   1 +
>  arch/arm/boot/dts/armada-38x.dtsi                  |   7 +
>  arch/arm/configs/mvebu_v7_defconfig                |   1 +
>  drivers/rtc/Kconfig                                |  10 +
>  drivers/rtc/Makefile                               |   1 +
>  drivers/rtc/rtc-armada38x.c                        | 320 +++++++++++++++++++++
>  7 files changed, 362 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/rtc/armada-380-rtc.txt
>  create mode 100644 drivers/rtc/rtc-armada38x.c
> 


-- 
Gregory Clement, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com

Re: [PATCH v4 0/5] Add a new RTC driver for recent mvebu SoCs

[Gregory CLEMENT]

Hi,


On 15/01/2015 18:23, Gregory CLEMENT wrote:
> Hi,
> 
> The Marvell Armada 38x SoCs contains an RTC which differs from the RTC
> used in the other mvebu SoCs until now. This forth version of the
> patch set adds support for this new IP and enable it in the Device
> Tree of the Armada 38x SoC.

This last version of this series have been sent 3 weeks ago. Is there
an hope to be merged in 3.20 ?

Should they go through via Andrew Morten's tree ?


Thanks,

Gregory


> 
> Thanks,
> 
> Grégory
> 
> Changelog
> 
> v3 -> v4:
> 
> - Formatted the device tree binding documentation in a better way
> - Renamed the soc-int regmap to rtc-soc because this group of register
>   was not only about the interrupt.
> - Fixed the rtc_delayed_write function. I found the exact description
>   of the WA to use, and the wait should really be after the write.
> 
> v2 -> v3:
> 
> - Fixed the reg-names description in the dt binding documentation
> - Used the delayed version of the writel in everyplace.
> 
> v1 -> v2:
> 
> - Used reg-names to identify the registers in the device tree
> - Changed the space into tab in the MAINTAINERS file
> - Emphasized that the 5s wait was only needed between two consecutive
>   writes
> - Reduced the wait in the set_time function, 100ms were enough
> - If no interrupt was available, then disable the alarm related
>   functions
> - Fixed the critical sections
> - Updated the mvebu_v7_defconfig by enabling the new RTC support
> 
> 
> Gregory CLEMENT (5):
>   rtc: armada38x: Add the device tree binding documentation
>   drivers/rtc/rtc-armada38x: Add a new RTC driver for recent mvebu SoCs
>   MAINTAINERS: Add the RTC driver for the Armada38x
>   ARM: mvebu: add Device Tree description of RTC on Armada 38x
>   ARM: mvebu: enable Armada 38x RTC driver in mvebu_v7_defconfig
> 
>  .../devicetree/bindings/rtc/armada-380-rtc.txt     |  22 ++
>  MAINTAINERS                                        |   1 +
>  arch/arm/boot/dts/armada-38x.dtsi                  |   7 +
>  arch/arm/configs/mvebu_v7_defconfig                |   1 +
>  drivers/rtc/Kconfig                                |  10 +
>  drivers/rtc/Makefile                               |   1 +
>  drivers/rtc/rtc-armada38x.c                        | 320 +++++++++++++++++++++
>  7 files changed, 362 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/rtc/armada-380-rtc.txt
>  create mode 100644 drivers/rtc/rtc-armada38x.c
> 


-- 
Gregory Clement, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html