From: Gregory CLEMENT <gregory.clement@bootlin.com>
To: "Marek Behún" <marek.behun@nic.cz>
Cc: linux-kernel@vger.kernel.org
Subject: Re: [PATCH mvebu-dt64] arm64: dts: marvell: armada-37xx: Add DTS file for Turris Mox
Date: Thu, 30 Aug 2018 17:11:18 +0200 [thread overview]
Message-ID: <87h8jbj3e1.fsf@bootlin.com> (raw)
In-Reply-To: <20180830150544.14814-1-marek.behun@nic.cz> ("Marek Behún"'s message of "Thu, 30 Aug 2018 17:05:44 +0200")
Hi Marek,
On jeu., août 30 2018, Marek Behún <marek.behun@nic.cz> wrote:
> This adds support for the Turris Mox board from CZ.NIC.
>
> Turris Mox is as modular router based on the Armada 3720 SOC (same as
> EspressoBin).
>
> The basic module can be extended by different modules.
> When those modules are connected, U-Boot shall patch this device-tree
> by enabling nodes corresponding to those modules.
could you resubmit it adding the other mvebu maintainer and the arm linux
kernel mailing as mentioned in the MAINTAINER file?
Thanks,
Gregory
>
> Signed-off-by: Marek Behún <marek.behun@nic.cz>
> ---
> .../arm/marvell/armada-3720-turris-mox.txt | 6 +
> arch/arm64/boot/dts/marvell/Makefile | 1 +
> .../boot/dts/marvell/armada-3720-turris-mox.dts | 817 +++++++++++++++++++++
> 3 files changed, 824 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/arm/marvell/armada-3720-turris-mox.txt
> create mode 100644 arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
>
> diff --git
> a/Documentation/devicetree/bindings/arm/marvell/armada-3720-turris-mox.txt
> b/Documentation/devicetree/bindings/arm/marvell/armada-3720-turris-mox.txt
> new file mode 100644
> index 000000000000..408fc07a9bbf
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/arm/marvell/armada-3720-turris-mox.txt
> @@ -0,0 +1,6 @@
> +CZ.NIC's Turris Mox SOHO router Device Tree Bindings
> +----------------------------------------------------
> +
> +Required root node property:
> +
> +compatible: must contain "cznic,turris-mox"
> diff --git a/arch/arm64/boot/dts/marvell/Makefile b/arch/arm64/boot/dts/marvell/Makefile
> index ea9d49f2a911..1dd89d1bf8ad 100644
> --- a/arch/arm64/boot/dts/marvell/Makefile
> +++ b/arch/arm64/boot/dts/marvell/Makefile
> @@ -2,6 +2,7 @@
> # Mvebu SoC Family
> dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-db.dtb
> dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-espressobin.dtb
> +dtb-$(CONFIG_ARCH_MVEBU) += armada-3720-turris-mox.dtb
> dtb-$(CONFIG_ARCH_MVEBU) += armada-7040-db.dtb
> dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-db.dtb
> dtb-$(CONFIG_ARCH_MVEBU) += armada-8040-mcbin.dtb
> diff --git a/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
> new file mode 100644
> index 000000000000..9267ae96f14f
> --- /dev/null
> +++ b/arch/arm64/boot/dts/marvell/armada-3720-turris-mox.dts
> @@ -0,0 +1,817 @@
> +// SPDX-License-Identifier: GPL-2.0+ or X11
> +/*
> + * Device Tree file for CZ.NIC Turris Mox Board
> + * 2018 by Marek Behun <marek.behun@nic.cz>
> + */
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include "armada-372x.dtsi"
> +
> +/ {
> + model = "CZ.NIC Turris Mox Board";
> + compatible = "cznic,turris-mox", "marvell,armada3720",
> + "marvell,armada3710";
> +
> + aliases {
> + spi0 = &spi0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + memory@0 {
> + device_type = "memory";
> + reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + red {
> + gpios = <&gpiosb 21 GPIO_ACTIVE_LOW>;
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +
> + gpio_keys {
> + compatible = "gpio-keys";
> +
> + reset_button {
> + label = "reset";
> + linux,code = <BTN_MISC>;
> + gpios = <&gpiosb 20 GPIO_ACTIVE_LOW>;
> + debounce-interval = <60>;
> + };
> + };
> +
> + exp_usb3_vbus: usb3-vbus {
> + compatible = "regulator-fixed";
> + regulator-name = "usb3-vbus";
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> + enable-active-high;
> + regulator-always-on;
> + gpio = <&gpiosb 0 GPIO_ACTIVE_HIGH>;
> + };
> +
> + usb3_phy: usb3-phy {
> + compatible = "usb-nop-xceiv";
> + vcc-supply = <&exp_usb3_vbus>;
> + };
> +
> + vsdc_reg: vsdc_reg {
> + compatible = "regulator-gpio";
> + regulator-name = "vsdc";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> +
> + gpios = <&gpiosb 23 GPIO_ACTIVE_HIGH>;
> + gpios-states = <0>;
> + states = <1800000 0x1
> + 3300000 0x0>;
> + enable-active-high;
> + };
> +
> + vsdio_reg: vsdio_reg {
> + compatible = "regulator-gpio";
> + regulator-name = "vsdio";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-boot-on;
> +
> + gpios = <&gpiosb 22 GPIO_ACTIVE_HIGH>;
> + gpios-states = <0>;
> + states = <1800000 0x1
> + 3300000 0x0>;
> + enable-active-high;
> + };
> +
> + sfp: sfp {
> + compatible = "sff,sfp+";
> + i2c-bus = <&i2c0>;
> + los-gpio = <&moxtet_sfp 0 GPIO_ACTIVE_HIGH>;
> + tx-fault-gpio = <&moxtet_sfp 1 GPIO_ACTIVE_HIGH>;
> + mod-def0-gpio = <&moxtet_sfp 2 GPIO_ACTIVE_LOW>;
> + tx-disable-gpio = <&moxtet_sfp 3 GPIO_ACTIVE_HIGH>;
> + rate-select0-gpio = <&moxtet_sfp 4 GPIO_ACTIVE_HIGH>;
> + status = "disabled";
> + };
> +};
> +
> +&pinctrl_nb {
> + spi_cs1_pins: spi-cs1-pins {
> + groups = "spi_cs1";
> + function = "spi";
> + };
> +
> + sdio0_pins: sdio0-pins {
> + groups = "sdio0";
> + function = "sdio";
> + };
> +};
> +
> +&pinctrl_sb {
> + sdio_sb_pins: sdio-sb-pins {
> + groups = "sdio_sb";
> + function = "sdio";
> + };
> +
> + smi_pins: smi-pins {
> + groups = "smi";
> + function = "smi";
> + };
> +
> + pcie_pins: pcie1-pins {
> + groups = "pcie1";
> + function = "gpio";
> + };
> +};
> +
> +&i2c0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c1_pins>;
> + status = "okay";
> +
> + rtc@6f {
> + compatible = "microchip,mcp7940x";
> + reg = <0x6f>;
> + };
> +};
> +
> +&pcie0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pcie_pins>;
> + status = "okay";
> + max-link-speed = <2>;
> + reset-gpio = <&gpiosb 3 GPIO_ACTIVE_HIGH>;
> +
> + /* this shall be enabled by u-boot if the PCIe module is present */
> + status = "disabled";
> +};
> +
> +&uart0 {
> + status = "okay";
> +};
> +
> +ð0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&rgmii_pins>;
> + phy-mode = "rgmii-id";
> + phy = <&phy1>;
> + status = "okay";
> +};
> +
> +ð1 {
> + phy-mode = "1000base-x";
> + managed = "in-band-status";
> +};
> +
> +&mdio {
> + pinctrl-names = "default";
> + pinctrl-0 = <&smi_pins>;
> + status = "okay";
> +
> + phy1: ethernet-phy@1 {
> + reg = <1>;
> + };
> +
> + switch0@10 {
> + compatible = "marvell,mv88e6190";
> + reg = <0x10 0>;
> + dsa,member = <0 0>;
> + interrupt-parent = <&gpiosb>;
> + interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
> + status = "disabled";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + switch0phy1: switch0phy1@1 {
> + reg = <0x1>;
> + };
> +
> + switch0phy2: switch0phy2@2 {
> + reg = <0x2>;
> + };
> +
> + switch0phy3: switch0phy3@3 {
> + reg = <0x3>;
> + };
> +
> + switch0phy4: switch0phy4@4 {
> + reg = <0x4>;
> + };
> +
> + switch0phy5: switch0phy5@5 {
> + reg = <0x5>;
> + };
> +
> + switch0phy6: switch0phy6@6 {
> + reg = <0x6>;
> + };
> +
> + switch0phy7: switch0phy7@7 {
> + reg = <0x7>;
> + };
> +
> + switch0phy8: switch0phy8@8 {
> + reg = <0x8>;
> + };
> + };
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@1 {
> + reg = <0x1>;
> + label = "lan1";
> + phy-handle = <&switch0phy1>;
> + };
> +
> + port@2 {
> + reg = <0x2>;
> + label = "lan2";
> + phy-handle = <&switch0phy2>;
> + };
> +
> + port@3 {
> + reg = <0x3>;
> + label = "lan3";
> + phy-handle = <&switch0phy3>;
> + };
> +
> + port@4 {
> + reg = <0x4>;
> + label = "lan4";
> + phy-handle = <&switch0phy4>;
> + };
> +
> + port@5 {
> + reg = <0x5>;
> + label = "lan5";
> + phy-handle = <&switch0phy5>;
> + };
> +
> + port@6 {
> + reg = <0x6>;
> + label = "lan6";
> + phy-handle = <&switch0phy6>;
> + };
> +
> + port@7 {
> + reg = <0x7>;
> + label = "lan7";
> + phy-handle = <&switch0phy7>;
> + };
> +
> + port@8 {
> + reg = <0x8>;
> + label = "lan8";
> + phy-handle = <&switch0phy8>;
> + };
> +
> + port@9 {
> + reg = <0x9>;
> + label = "cpu";
> + ethernet = <ð1>;
> + };
> +
> + switch0port10: port@a {
> + reg = <0xa>;
> + label = "dsa";
> + phy-mode = "2500base-x";
> + link = <&switch1port9 &switch2port9>;
> + status = "disabled";
> + };
> +
> + port-sfp@a {
> + reg = <0xa>;
> + label = "sfp";
> + sfp = <&sfp>;
> + phy-mode = "sgmii";
> + managed = "in-band-status";
> + status = "disabled";
> + };
> + };
> + };
> +
> + switch0@2 {
> + compatible = "marvell,mv88e6085";
> + reg = <0x2 0>;
> + dsa,member = <0 0>;
> + interrupt-parent = <&gpiosb>;
> + interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
> + status = "disabled";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + switch0phy1_topaz: switch0phy1@11 {
> + reg = <0x11>;
> + };
> +
> + switch0phy2_topaz: switch0phy2@12 {
> + reg = <0x12>;
> + };
> +
> + switch0phy3_topaz: switch0phy3@13 {
> + reg = <0x13>;
> + };
> +
> + switch0phy4_topaz: switch0phy4@14 {
> + reg = <0x14>;
> + };
> + };
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@1 {
> + reg = <0x1>;
> + label = "lan1";
> + phy-handle = <&switch0phy1_topaz>;
> + };
> +
> + port@2 {
> + reg = <0x2>;
> + label = "lan2";
> + phy-handle = <&switch0phy2_topaz>;
> + };
> +
> + port@3 {
> + reg = <0x3>;
> + label = "lan3";
> + phy-handle = <&switch0phy3_topaz>;
> + };
> +
> + port@4 {
> + reg = <0x4>;
> + label = "lan4";
> + phy-handle = <&switch0phy4_topaz>;
> + };
> +
> + port@5 {
> + reg = <0x5>;
> + label = "cpu";
> + ethernet = <ð1>;
> + };
> + };
> + };
> +
> + switch1@11 {
> + compatible = "marvell,mv88e6190";
> + reg = <0x11 0>;
> + dsa,member = <0 1>;
> + interrupt-parent = <&gpiosb>;
> + interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
> + status = "disabled";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + switch1phy1: switch1phy1@1 {
> + reg = <0x1>;
> + };
> +
> + switch1phy2: switch1phy2@2 {
> + reg = <0x2>;
> + };
> +
> + switch1phy3: switch1phy3@3 {
> + reg = <0x3>;
> + };
> +
> + switch1phy4: switch1phy4@4 {
> + reg = <0x4>;
> + };
> +
> + switch1phy5: switch1phy5@5 {
> + reg = <0x5>;
> + };
> +
> + switch1phy6: switch1phy6@6 {
> + reg = <0x6>;
> + };
> +
> + switch1phy7: switch1phy7@7 {
> + reg = <0x7>;
> + };
> +
> + switch1phy8: switch1phy8@8 {
> + reg = <0x8>;
> + };
> + };
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@1 {
> + reg = <0x1>;
> + label = "lan9";
> + phy-handle = <&switch1phy1>;
> + };
> +
> + port@2 {
> + reg = <0x2>;
> + label = "lan10";
> + phy-handle = <&switch1phy2>;
> + };
> +
> + port@3 {
> + reg = <0x3>;
> + label = "lan11";
> + phy-handle = <&switch1phy3>;
> + };
> +
> + port@4 {
> + reg = <0x4>;
> + label = "lan12";
> + phy-handle = <&switch1phy4>;
> + };
> +
> + port@5 {
> + reg = <0x5>;
> + label = "lan13";
> + phy-handle = <&switch1phy5>;
> + };
> +
> + port@6 {
> + reg = <0x6>;
> + label = "lan14";
> + phy-handle = <&switch1phy6>;
> + };
> +
> + port@7 {
> + reg = <0x7>;
> + label = "lan15";
> + phy-handle = <&switch1phy7>;
> + };
> +
> + port@8 {
> + reg = <0x8>;
> + label = "lan16";
> + phy-handle = <&switch1phy8>;
> + };
> +
> + switch1port9: port@9 {
> + reg = <0x9>;
> + label = "dsa";
> + phy-mode = "2500base-x";
> + link = <&switch0port10>;
> + };
> +
> + switch1port10: port@a {
> + reg = <0xa>;
> + label = "dsa";
> + phy-mode = "2500base-x";
> + link = <&switch2port9>;
> + status = "disabled";
> + };
> +
> + port-sfp@a {
> + reg = <0xa>;
> + label = "sfp";
> + sfp = <&sfp>;
> + phy-mode = "sgmii";
> + managed = "in-band-status";
> + status = "disabled";
> + };
> + };
> + };
> +
> + switch1@2 {
> + compatible = "marvell,mv88e6085";
> + reg = <0x2 0>;
> + dsa,member = <0 1>;
> + interrupt-parent = <&gpiosb>;
> + interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
> + status = "disabled";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + switch1phy1_topaz: switch1phy1@11 {
> + reg = <0x11>;
> + };
> +
> + switch1phy2_topaz: switch1phy2@12 {
> + reg = <0x12>;
> + };
> +
> + switch1phy3_topaz: switch1phy3@13 {
> + reg = <0x13>;
> + };
> +
> + switch1phy4_topaz: switch1phy4@14 {
> + reg = <0x14>;
> + };
> + };
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@1 {
> + reg = <0x1>;
> + label = "lan9";
> + phy-handle = <&switch1phy1_topaz>;
> + };
> +
> + port@2 {
> + reg = <0x2>;
> + label = "lan10";
> + phy-handle = <&switch1phy2_topaz>;
> + };
> +
> + port@3 {
> + reg = <0x3>;
> + label = "lan11";
> + phy-handle = <&switch1phy3_topaz>;
> + };
> +
> + port@4 {
> + reg = <0x4>;
> + label = "lan12";
> + phy-handle = <&switch1phy4_topaz>;
> + };
> +
> + port@5 {
> + reg = <0x5>;
> + label = "dsa";
> + phy-mode = "2500base-x";
> + link = <&switch0port10>;
> + };
> + };
> + };
> +
> + switch2@12 {
> + compatible = "marvell,mv88e6190";
> + reg = <0x12 0>;
> + dsa,member = <0 2>;
> + interrupt-parent = <&gpiosb>;
> + interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
> + status = "disabled";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + switch2phy1: switch2phy1@1 {
> + reg = <0x1>;
> + };
> +
> + switch2phy2: switch2phy2@2 {
> + reg = <0x2>;
> + };
> +
> + switch2phy3: switch2phy3@3 {
> + reg = <0x3>;
> + };
> +
> + switch2phy4: switch2phy4@4 {
> + reg = <0x4>;
> + };
> +
> + switch2phy5: switch2phy5@5 {
> + reg = <0x5>;
> + };
> +
> + switch2phy6: switch2phy6@6 {
> + reg = <0x6>;
> + };
> +
> + switch2phy7: switch2phy7@7 {
> + reg = <0x7>;
> + };
> +
> + switch2phy8: switch2phy8@8 {
> + reg = <0x8>;
> + };
> + };
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@1 {
> + reg = <0x1>;
> + label = "lan17";
> + phy-handle = <&switch2phy1>;
> + };
> +
> + port@2 {
> + reg = <0x2>;
> + label = "lan18";
> + phy-handle = <&switch2phy2>;
> + };
> +
> + port@3 {
> + reg = <0x3>;
> + label = "lan19";
> + phy-handle = <&switch2phy3>;
> + };
> +
> + port@4 {
> + reg = <0x4>;
> + label = "lan20";
> + phy-handle = <&switch2phy4>;
> + };
> +
> + port@5 {
> + reg = <0x5>;
> + label = "lan21";
> + phy-handle = <&switch2phy5>;
> + };
> +
> + port@6 {
> + reg = <0x6>;
> + label = "lan22";
> + phy-handle = <&switch2phy6>;
> + };
> +
> + port@7 {
> + reg = <0x7>;
> + label = "lan23";
> + phy-handle = <&switch2phy7>;
> + };
> +
> + port@8 {
> + reg = <0x8>;
> + label = "lan24";
> + phy-handle = <&switch2phy8>;
> + };
> +
> + switch2port9: port@9 {
> + reg = <0x9>;
> + label = "dsa";
> + phy-mode = "2500base-x";
> + link = <&switch1port10 &switch0port10>;
> + };
> +
> + port-sfp@a {
> + reg = <0xa>;
> + label = "sfp";
> + sfp = <&sfp>;
> + phy-mode = "sgmii";
> + managed = "in-band-status";
> + status = "disabled";
> + };
> + };
> + };
> +
> + switch2@2 {
> + compatible = "marvell,mv88e6085";
> + reg = <0x2 0>;
> + dsa,member = <0 2>;
> + interrupt-parent = <&gpiosb>;
> + interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
> + status = "disabled";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + switch2phy1_topaz: switch2phy1@11 {
> + reg = <0x11>;
> + };
> +
> + switch2phy2_topaz: switch2phy2@12 {
> + reg = <0x12>;
> + };
> +
> + switch2phy3_topaz: switch2phy3@13 {
> + reg = <0x13>;
> + };
> +
> + switch2phy4_topaz: switch2phy4@14 {
> + reg = <0x14>;
> + };
> + };
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@1 {
> + reg = <0x1>;
> + label = "lan17";
> + phy-handle = <&switch2phy1_topaz>;
> + };
> +
> + port@2 {
> + reg = <0x2>;
> + label = "lan18";
> + phy-handle = <&switch2phy2_topaz>;
> + };
> +
> + port@3 {
> + reg = <0x3>;
> + label = "lan19";
> + phy-handle = <&switch2phy3_topaz>;
> + };
> +
> + port@4 {
> + reg = <0x4>;
> + label = "lan20";
> + phy-handle = <&switch2phy4_topaz>;
> + };
> +
> + port@5 {
> + reg = <0x5>;
> + label = "dsa";
> + phy-mode = "2500base-x";
> + link = <&switch1port10 &switch0port10>;
> + };
> + };
> + };
> +
> +};
> +
> +&sdhci0 {
> + wp-inverted;
> + bus-width = <4>;
> + cd-gpios = <&gpionb 10 GPIO_ACTIVE_HIGH>;
> + vqmmc-supply = <&vsdc_reg>;
> + marvell,pad-type = "sd";
> + status = "okay";
> +};
> +
> +&sdhci1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdio0_pins &sdio_sb_pins>;
> + non-removable;
> + bus-width = <4>;
> + marvell,pad-type = "sd";
> + vqmmc-supply = <&vsdio_reg>;
> + status = "okay";
> +};
> +
> +&spi0 {
> + status = "okay";
> + pinctrl-names = "default";
> + pinctrl-0 = <&spi_quad_pins &spi_cs1_pins>;
> + assigned-clocks = <&nb_periph_clk 7>;
> + assigned-clock-parents = <&tbg 1>;
> + assigned-clock-rates = <20000000>;
> +
> + spi-flash@0 {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + spi-max-frequency = <2000000>;
> +
> + partition@0 {
> + label = "u-boot";
> + reg = <0x0 0x3f0000>;
> + };
> +
> + partition@3f0000 {
> + label = "u-boot-env";
> + reg = <0x180000 0x10000>;
> + };
> +
> + partition@400000 {
> + label = "Rescue system";
> + reg = <0x190000 0x670000>;
> + };
> + };
> +
> + moxtet@1 {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + compatible = "cznic,moxtet";
> + reg = <1>;
> + devrst-gpio = <&gpiosb 2 GPIO_ACTIVE_LOW>;
> + spi-max-frequency = <1000000>;
> + spi-cpol;
> + spi-cpha;
> +
> + moxtet_sfp: moxtet-sfp@0 {
> + compatible = "cznic,moxtet-gpio";
> + gpio-controller;
> + #gpio-cells = <2>;
> + reg = <0>;
> + moxtet,id = <1>;
> + moxtet,input-mask = <0x7>;
> + moxtet,output-mask = <0x3>;
> + status = "disabled";
> + };
> + };
> +};
> +
> +&usb3 {
> + status = "okay";
> + usb-phy = <&usb3_phy>;
> +};
> --
> 2.16.4
>
--
Gregory Clement, Bootlin
Embedded Linux and Kernel engineering
http://bootlin.com
next prev parent reply other threads:[~2018-08-30 15:11 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2018-08-30 15:05 [PATCH mvebu-dt64] arm64: dts: marvell: armada-37xx: Add DTS file for Turris Mox Marek Behún
2018-08-30 15:11 ` Gregory CLEMENT [this message]
-- strict thread matches above, loose matches on Subject: below --
2018-08-30 15:23 Marek Behún
2018-08-30 15:57 ` Andrew Lunn
2018-08-30 16:16 ` Marek Behun
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=87h8jbj3e1.fsf@bootlin.com \
--to=gregory.clement@bootlin.com \
--cc=linux-kernel@vger.kernel.org \
--cc=marek.behun@nic.cz \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.