[ath9k-devel] [PATCH v2] ath9k: Switch to using mac80211 intermediate software queues.

["Toke Høiland-Jørgensen" <toke@toke.dk>]

Felix Fietkau <nbd@nbd.name> writes:

> On 2016-07-06 20:52, Toke H?iland-J?rgensen wrote:
>> Felix Fietkau <nbd@nbd.name> writes:
>> 
>>> On 2016-07-06 18:16, Toke H?iland-J?rgensen wrote:
>>>> This switches ath9k over to using the mac80211 intermediate software
>>>> queueing mechanism for data packets. It removes the queueing inside the
>>>> driver, except for the retry queue, and instead pulls from mac80211 when
>>>> a packet is needed. The retry queue is used to store a packet that was
>>>> pulled but can't be sent immediately.
>>>> 
>>>> The old code path in ath_tx_start that would queue packets has been
>>>> removed completely, as has the qlen limit tunables (since there's no
>>>> longer a queue in the driver to limit).
>>>> 
>>>> Based on Tim's original patch set, but reworked quite thoroughly.
>>>> 
>>>> Cc: Tim Shepard <shep@alum.mit.edu>
>>>> Cc: Felix Fietkau <nbd@nbd.name>
>>>> Signed-off-by: Toke H?iland-J?rgensen <toke@toke.dk>
>>>> ---
>>>> Changes since v1:
>>>>   - Remove the old intermediate queueing logic completely instead of
>>>>     just disabling it.
>>>>   - Remove the qlen debug tunables.
>>>>   - Remove the force_channel parameter from struct txctl (since we just
>>>>     removed the code path that was using it).
>>>> 
>>>>  drivers/net/wireless/ath/ath9k/ath9k.h     |  12 +-
>>>>  drivers/net/wireless/ath/ath9k/channel.c   |   2 -
>>>>  drivers/net/wireless/ath/ath9k/debug.c     |  14 +-
>>>>  drivers/net/wireless/ath/ath9k/debug.h     |   2 -
>>>>  drivers/net/wireless/ath/ath9k/debug_sta.c |   4 +-
>>>>  drivers/net/wireless/ath/ath9k/init.c      |   2 +-
>>>>  drivers/net/wireless/ath/ath9k/main.c      |   1 +
>>>>  drivers/net/wireless/ath/ath9k/xmit.c      | 307 +++++++++++------------------
>>>>  8 files changed, 130 insertions(+), 214 deletions(-)
>>> Nice work!
>> 
>> Thanks :)
>> 
>>>> diff --git a/drivers/net/wireless/ath/ath9k/xmit.c b/drivers/net/wireless/ath/ath9k/xmit.c
>>>> index fe795fc..4077eeb 100644
>>>> --- a/drivers/net/wireless/ath/ath9k/xmit.c
>>>> +++ b/drivers/net/wireless/ath/ath9k/xmit.c
>>>> @@ -912,8 +923,16 @@ ath_tx_get_tid_subframe(struct ath_softc *sc, struct ath_txq *txq,
>>>>  		seqno = bf->bf_state.seqno;
>>>>  
>>>>  		/* do not step over block-ack window */
>>>> -		if (!BAW_WITHIN(tid->seq_start, tid->baw_size, seqno))
>>>> +		if (!BAW_WITHIN(tid->seq_start, tid->baw_size, seqno)) {
>>>> +			__skb_queue_tail(&tid->retry_q, skb);
>>>> +
>>>> +			/* If there are other skbs in the retry q, they are
>>>> +			 * probably within the BAW, so loop immediately to get
>>>> +			 * one of them. Otherwise the queue can get stuck. */
>>>> +			if (!skb_queue_is_first(&tid->retry_q, skb))
>>>> +				continue;
>>> Not sure if this can happen, but if we ever somehow end up with two skbs
>>> in the retry queue that do not fit into the Block-Ack window, there's
>>> potential for an infinite loop here.
>> 
>> Yes, I realise that (v1 contained a comment on that). However, I don't
>> actually think it can happen: The code will only ever put one skb from
>> the intermediate queues on the retry queue (ath_tid_pull() is only
>> called if the retry queue is empty). Everything else on there are actual
>> retries that have been put on there by ath_tx_complete_aggr(). Figure
>> the latter will always be within the BAW?
> I think it would be a good idea to have a check there (with WARN_ON), in
> case there's some weird corner case with seqno handling, software retry
> and aggregation state changes.

Right, can do :)

-Toke