* [PATCH] dt: bindings: add new dt entry for pre calibration in qcom,ath10k.txt
@ 2016-03-10 10:12 ` Raja Mani
0 siblings, 0 replies; 12+ messages in thread
From: Raja Mani @ 2016-03-10 10:12 UTC (permalink / raw)
To: kvalo-A+ZNKFmMK5xy9aJCnZT0Uw
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA,
ath10k-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-wireless-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA, robh-DgEjT+Ai2ygdnm+yROfE0A,
Raja Mani
There two things done in this patch,
1) Existing device tree entry 'qcom,ath10k-calibration-data' carries
not only calibration data, it carries board specific data too.
So, make appropriate update in doc.
2) ipq4019 wifi needs new devie tree entry to carry calibration
data alone (called pre cal data, it doesn't include any other info).
Using 'qcom,ath10k-calibration-data' for ipq4019 would alter
the purpose of it. Hence, add new device tree entry called
'qcom,ath10k-pre-calibration-data' to carry only pre calibration data.
Signed-off-by: Raja Mani <rmani-Rm6X0d1/PG5y9aJCnZT0Uw@public.gmane.org>
---
Below patches covers the corresponding changes in the ath10k driver.
It's posted separately to ath10k and linux-wireless mailing list.
1) ath10k: pass cal data location as an argument to ath10k_download_cal_{file|dt}
2) ath10k: move cal data len to hw_params
3) ath10k: incorporate qca4019 cal data download sequence
.../bindings/net/wireless/qcom,ath10k.txt | 23 +++++++++++++++-------
1 file changed, 16 insertions(+), 7 deletions(-)
diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt
index 96aae6b..74d7f0a 100644
--- a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt
+++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt
@@ -5,12 +5,18 @@ Required properties:
* "qcom,ath10k"
* "qcom,ipq4019-wifi"
-PCI based devices uses compatible string "qcom,ath10k" and takes only
-calibration data via "qcom,ath10k-calibration-data". Rest of the properties
-are not applicable for PCI based devices.
+PCI based devices uses compatible string "qcom,ath10k" and takes calibration
+data along with board specific data via "qcom,ath10k-calibration-data".
+Rest of the properties are not applicable for PCI based devices.
AHB based devices (i.e. ipq4019) uses compatible string "qcom,ipq4019-wifi"
-and also uses most of the properties defined in this doc.
+and also uses most of the properties defined in this doc (except
+"qcom,ath10k-calibration-data"). It uses "qcom,ath10k-pre-calibration-data"
+to carry pre calibration data.
+
+In general, entry "qcom,ath10k-pre-calibration-data" and
+"qcom,ath10k-calibration-data" conflict with each other and only one
+can be provided per device.
Optional properties:
- reg: Address and length of the register set for the device.
@@ -35,8 +41,11 @@ Optional properties:
- qcom,msi_addr: MSI interrupt address.
- qcom,msi_base: Base value to add before writing MSI data into
MSI address register.
-- qcom,ath10k-calibration-data : calibration data as an array, the
- length can vary between hw versions
+- qcom,ath10k-calibration-data : calibration data + board specific data
+ as an array, the length can vary between
+ hw versions.
+- qcom,ath10k-pre-calibration-data : pre calibration data as an array,
+ the length can vary between hw versions.
Example (to supply the calibration data alone):
@@ -105,5 +114,5 @@ wifi0: wifi@a000000 {
"legacy";
qcom,msi_addr = <0x0b006040>;
qcom,msi_base = <0x40>;
- qcom,ath10k-calibration-data = [ 01 02 03 ... ];
+ qcom,ath10k-pre-calibration-data = [ 01 02 03 ... ];
};
--
1.8.1.2
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply related [flat|nested] 12+ messages in thread* [PATCH] dt: bindings: add new dt entry for pre calibration in qcom,ath10k.txt
@ 2016-03-10 10:12 ` Raja Mani
0 siblings, 0 replies; 12+ messages in thread
From: Raja Mani @ 2016-03-10 10:12 UTC (permalink / raw)
To: kvalo; +Cc: devicetree, ath10k, linux-wireless, linux-kernel, robh, Raja Mani
There two things done in this patch,
1) Existing device tree entry 'qcom,ath10k-calibration-data' carries
not only calibration data, it carries board specific data too.
So, make appropriate update in doc.
2) ipq4019 wifi needs new devie tree entry to carry calibration
data alone (called pre cal data, it doesn't include any other info).
Using 'qcom,ath10k-calibration-data' for ipq4019 would alter
the purpose of it. Hence, add new device tree entry called
'qcom,ath10k-pre-calibration-data' to carry only pre calibration data.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
---
Below patches covers the corresponding changes in the ath10k driver.
It's posted separately to ath10k and linux-wireless mailing list.
1) ath10k: pass cal data location as an argument to ath10k_download_cal_{file|dt}
2) ath10k: move cal data len to hw_params
3) ath10k: incorporate qca4019 cal data download sequence
.../bindings/net/wireless/qcom,ath10k.txt | 23 +++++++++++++++-------
1 file changed, 16 insertions(+), 7 deletions(-)
diff --git a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt
index 96aae6b..74d7f0a 100644
--- a/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt
+++ b/Documentation/devicetree/bindings/net/wireless/qcom,ath10k.txt
@@ -5,12 +5,18 @@ Required properties:
* "qcom,ath10k"
* "qcom,ipq4019-wifi"
-PCI based devices uses compatible string "qcom,ath10k" and takes only
-calibration data via "qcom,ath10k-calibration-data". Rest of the properties
-are not applicable for PCI based devices.
+PCI based devices uses compatible string "qcom,ath10k" and takes calibration
+data along with board specific data via "qcom,ath10k-calibration-data".
+Rest of the properties are not applicable for PCI based devices.
AHB based devices (i.e. ipq4019) uses compatible string "qcom,ipq4019-wifi"
-and also uses most of the properties defined in this doc.
+and also uses most of the properties defined in this doc (except
+"qcom,ath10k-calibration-data"). It uses "qcom,ath10k-pre-calibration-data"
+to carry pre calibration data.
+
+In general, entry "qcom,ath10k-pre-calibration-data" and
+"qcom,ath10k-calibration-data" conflict with each other and only one
+can be provided per device.
Optional properties:
- reg: Address and length of the register set for the device.
@@ -35,8 +41,11 @@ Optional properties:
- qcom,msi_addr: MSI interrupt address.
- qcom,msi_base: Base value to add before writing MSI data into
MSI address register.
-- qcom,ath10k-calibration-data : calibration data as an array, the
- length can vary between hw versions
+- qcom,ath10k-calibration-data : calibration data + board specific data
+ as an array, the length can vary between
+ hw versions.
+- qcom,ath10k-pre-calibration-data : pre calibration data as an array,
+ the length can vary between hw versions.
Example (to supply the calibration data alone):
@@ -105,5 +114,5 @@ wifi0: wifi@a000000 {
"legacy";
qcom,msi_addr = <0x0b006040>;
qcom,msi_base = <0x40>;
- qcom,ath10k-calibration-data = [ 01 02 03 ... ];
+ qcom,ath10k-pre-calibration-data = [ 01 02 03 ... ];
};
--
1.8.1.2
^ permalink raw reply related [flat|nested] 12+ messages in thread* Re: [PATCH] dt: bindings: add new dt entry for pre calibration in qcom,ath10k.txt
2016-03-10 10:12 ` Raja Mani
(?)
@ 2016-03-18 16:18 ` Rob Herring
-1 siblings, 0 replies; 12+ messages in thread
From: Rob Herring @ 2016-03-18 16:18 UTC (permalink / raw)
To: Raja Mani; +Cc: devicetree, kvalo, linux-wireless, linux-kernel, ath10k
On Thu, Mar 10, 2016 at 03:42:04PM +0530, Raja Mani wrote:
> There two things done in this patch,
>
> 1) Existing device tree entry 'qcom,ath10k-calibration-data' carries
> not only calibration data, it carries board specific data too.
> So, make appropriate update in doc.
>
> 2) ipq4019 wifi needs new devie tree entry to carry calibration
> data alone (called pre cal data, it doesn't include any other info).
> Using 'qcom,ath10k-calibration-data' for ipq4019 would alter
> the purpose of it. Hence, add new device tree entry called
> 'qcom,ath10k-pre-calibration-data' to carry only pre calibration data.
>
> Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
> ---
>
> Below patches covers the corresponding changes in the ath10k driver.
> It's posted separately to ath10k and linux-wireless mailing list.
Generally the series should be posted together. The rest should not be
merged until this patch is accepted.
>
> 1) ath10k: pass cal data location as an argument to ath10k_download_cal_{file|dt}
> 2) ath10k: move cal data len to hw_params
> 3) ath10k: incorporate qca4019 cal data download sequence
>
> .../bindings/net/wireless/qcom,ath10k.txt | 23 +++++++++++++++-------
> 1 file changed, 16 insertions(+), 7 deletions(-)
Acked-by: Rob Herring <robh@kernel.org>
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 12+ messages in thread* Re: [PATCH] dt: bindings: add new dt entry for pre calibration in qcom,ath10k.txt
@ 2016-03-18 16:18 ` Rob Herring
0 siblings, 0 replies; 12+ messages in thread
From: Rob Herring @ 2016-03-18 16:18 UTC (permalink / raw)
To: Raja Mani
Cc: kvalo-A+ZNKFmMK5xy9aJCnZT0Uw, devicetree-u79uwXL29TY76Z2rM5mHXA,
ath10k-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-wireless-u79uwXL29TY76Z2rM5mHXA,
linux-kernel-u79uwXL29TY76Z2rM5mHXA
On Thu, Mar 10, 2016 at 03:42:04PM +0530, Raja Mani wrote:
> There two things done in this patch,
>
> 1) Existing device tree entry 'qcom,ath10k-calibration-data' carries
> not only calibration data, it carries board specific data too.
> So, make appropriate update in doc.
>
> 2) ipq4019 wifi needs new devie tree entry to carry calibration
> data alone (called pre cal data, it doesn't include any other info).
> Using 'qcom,ath10k-calibration-data' for ipq4019 would alter
> the purpose of it. Hence, add new device tree entry called
> 'qcom,ath10k-pre-calibration-data' to carry only pre calibration data.
>
> Signed-off-by: Raja Mani <rmani-Rm6X0d1/PG5y9aJCnZT0Uw@public.gmane.org>
> ---
>
> Below patches covers the corresponding changes in the ath10k driver.
> It's posted separately to ath10k and linux-wireless mailing list.
Generally the series should be posted together. The rest should not be
merged until this patch is accepted.
>
> 1) ath10k: pass cal data location as an argument to ath10k_download_cal_{file|dt}
> 2) ath10k: move cal data len to hw_params
> 3) ath10k: incorporate qca4019 cal data download sequence
>
> .../bindings/net/wireless/qcom,ath10k.txt | 23 +++++++++++++++-------
> 1 file changed, 16 insertions(+), 7 deletions(-)
Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 12+ messages in thread* Re: [PATCH] dt: bindings: add new dt entry for pre calibration in qcom,ath10k.txt
@ 2016-03-18 16:18 ` Rob Herring
0 siblings, 0 replies; 12+ messages in thread
From: Rob Herring @ 2016-03-18 16:18 UTC (permalink / raw)
To: Raja Mani; +Cc: kvalo, devicetree, ath10k, linux-wireless, linux-kernel
On Thu, Mar 10, 2016 at 03:42:04PM +0530, Raja Mani wrote:
> There two things done in this patch,
>
> 1) Existing device tree entry 'qcom,ath10k-calibration-data' carries
> not only calibration data, it carries board specific data too.
> So, make appropriate update in doc.
>
> 2) ipq4019 wifi needs new devie tree entry to carry calibration
> data alone (called pre cal data, it doesn't include any other info).
> Using 'qcom,ath10k-calibration-data' for ipq4019 would alter
> the purpose of it. Hence, add new device tree entry called
> 'qcom,ath10k-pre-calibration-data' to carry only pre calibration data.
>
> Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
> ---
>
> Below patches covers the corresponding changes in the ath10k driver.
> It's posted separately to ath10k and linux-wireless mailing list.
Generally the series should be posted together. The rest should not be
merged until this patch is accepted.
>
> 1) ath10k: pass cal data location as an argument to ath10k_download_cal_{file|dt}
> 2) ath10k: move cal data len to hw_params
> 3) ath10k: incorporate qca4019 cal data download sequence
>
> .../bindings/net/wireless/qcom,ath10k.txt | 23 +++++++++++++++-------
> 1 file changed, 16 insertions(+), 7 deletions(-)
Acked-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 12+ messages in thread* Re: [PATCH] dt: bindings: add new dt entry for pre calibration in qcom,ath10k.txt
2016-03-18 16:18 ` Rob Herring
(?)
@ 2016-03-23 11:43 ` Valo, Kalle
-1 siblings, 0 replies; 12+ messages in thread
From: Valo, Kalle @ 2016-03-23 11:43 UTC (permalink / raw)
To: Rob Herring
Cc: devicetree@vger.kernel.org, linux-wireless@vger.kernel.org,
Raja Mani, ath10k@lists.infradead.org,
linux-kernel@vger.kernel.org
Rob Herring <robh@kernel.org> writes:
> On Thu, Mar 10, 2016 at 03:42:04PM +0530, Raja Mani wrote:
>> There two things done in this patch,
>>
>> 1) Existing device tree entry 'qcom,ath10k-calibration-data' carries
>> not only calibration data, it carries board specific data too.
>> So, make appropriate update in doc.
>>
>> 2) ipq4019 wifi needs new devie tree entry to carry calibration
>> data alone (called pre cal data, it doesn't include any other info).
>> Using 'qcom,ath10k-calibration-data' for ipq4019 would alter
>> the purpose of it. Hence, add new device tree entry called
>> 'qcom,ath10k-pre-calibration-data' to carry only pre calibration data.
>>
>> Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
>> ---
>>
>> Below patches covers the corresponding changes in the ath10k driver.
>> It's posted separately to ath10k and linux-wireless mailing list.
>
> Generally the series should be posted together. The rest should not be
> merged until this patch is accepted.
I'll merge them together, this as the first patch.
>> 1) ath10k: pass cal data location as an argument to ath10k_download_cal_{file|dt}
>> 2) ath10k: move cal data len to hw_params
>> 3) ath10k: incorporate qca4019 cal data download sequence
>>
>> .../bindings/net/wireless/qcom,ath10k.txt | 23 +++++++++++++++-------
>> 1 file changed, 16 insertions(+), 7 deletions(-)
>
> Acked-by: Rob Herring <robh@kernel.org>
Thanks.
--
Kalle Valo
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 12+ messages in thread* Re: [PATCH] dt: bindings: add new dt entry for pre calibration in qcom,ath10k.txt
@ 2016-03-23 11:43 ` Valo, Kalle
0 siblings, 0 replies; 12+ messages in thread
From: Valo, Kalle @ 2016-03-23 11:43 UTC (permalink / raw)
To: Rob Herring
Cc: Raja Mani, devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-wireless-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
ath10k-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org> writes:
> On Thu, Mar 10, 2016 at 03:42:04PM +0530, Raja Mani wrote:
>> There two things done in this patch,
>>
>> 1) Existing device tree entry 'qcom,ath10k-calibration-data' carries
>> not only calibration data, it carries board specific data too.
>> So, make appropriate update in doc.
>>
>> 2) ipq4019 wifi needs new devie tree entry to carry calibration
>> data alone (called pre cal data, it doesn't include any other info).
>> Using 'qcom,ath10k-calibration-data' for ipq4019 would alter
>> the purpose of it. Hence, add new device tree entry called
>> 'qcom,ath10k-pre-calibration-data' to carry only pre calibration data.
>>
>> Signed-off-by: Raja Mani <rmani-Rm6X0d1/PG5y9aJCnZT0Uw@public.gmane.org>
>> ---
>>
>> Below patches covers the corresponding changes in the ath10k driver.
>> It's posted separately to ath10k and linux-wireless mailing list.
>
> Generally the series should be posted together. The rest should not be
> merged until this patch is accepted.
I'll merge them together, this as the first patch.
>> 1) ath10k: pass cal data location as an argument to ath10k_download_cal_{file|dt}
>> 2) ath10k: move cal data len to hw_params
>> 3) ath10k: incorporate qca4019 cal data download sequence
>>
>> .../bindings/net/wireless/qcom,ath10k.txt | 23 +++++++++++++++-------
>> 1 file changed, 16 insertions(+), 7 deletions(-)
>
> Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
Thanks.
--
Kalle Valo--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 12+ messages in thread* Re: [PATCH] dt: bindings: add new dt entry for pre calibration in qcom,ath10k.txt
@ 2016-03-23 11:43 ` Valo, Kalle
0 siblings, 0 replies; 12+ messages in thread
From: Valo, Kalle @ 2016-03-23 11:43 UTC (permalink / raw)
To: Rob Herring
Cc: Raja Mani, devicetree@vger.kernel.org,
linux-wireless@vger.kernel.org, linux-kernel@vger.kernel.org,
ath10k@lists.infradead.org
Rob Herring <robh@kernel.org> writes:
> On Thu, Mar 10, 2016 at 03:42:04PM +0530, Raja Mani wrote:
>> There two things done in this patch,
>>
>> 1) Existing device tree entry 'qcom,ath10k-calibration-data' carries
>> not only calibration data, it carries board specific data too.
>> So, make appropriate update in doc.
>>
>> 2) ipq4019 wifi needs new devie tree entry to carry calibration
>> data alone (called pre cal data, it doesn't include any other info).
>> Using 'qcom,ath10k-calibration-data' for ipq4019 would alter
>> the purpose of it. Hence, add new device tree entry called
>> 'qcom,ath10k-pre-calibration-data' to carry only pre calibration data.
>>
>> Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
>> ---
>>
>> Below patches covers the corresponding changes in the ath10k driver.
>> It's posted separately to ath10k and linux-wireless mailing list.
>
> Generally the series should be posted together. The rest should not be
> merged until this patch is accepted.
I'll merge them together, this as the first patch.
>> 1) ath10k: pass cal data location as an argument to ath10k_download_cal_{file|dt}
>> 2) ath10k: move cal data len to hw_params
>> 3) ath10k: incorporate qca4019 cal data download sequence
>>
>> .../bindings/net/wireless/qcom,ath10k.txt | 23 +++++++++++++++-------
>> 1 file changed, 16 insertions(+), 7 deletions(-)
>
> Acked-by: Rob Herring <robh@kernel.org>
Thanks.
--
Kalle Valo
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH] dt: bindings: add new dt entry for pre calibration in qcom, ath10k.txt
2016-03-10 10:12 ` Raja Mani
(?)
@ 2016-03-23 12:07 ` Valo, Kalle
-1 siblings, 0 replies; 12+ messages in thread
From: Valo, Kalle @ 2016-03-23 12:07 UTC (permalink / raw)
To: Raja Mani
Cc: devicetree@vger.kernel.org, linux-wireless@vger.kernel.org,
linux-kernel@vger.kernel.org, ath10k@lists.infradead.org,
robh@kernel.org
Raja Mani <rmani@qti.qualcomm.com> writes:
> There two things done in this patch,
>
> 1) Existing device tree entry 'qcom,ath10k-calibration-data' carries
> not only calibration data, it carries board specific data too.
> So, make appropriate update in doc.
>
> 2) ipq4019 wifi needs new devie tree entry to carry calibration
> data alone (called pre cal data, it doesn't include any other info).
> Using 'qcom,ath10k-calibration-data' for ipq4019 would alter
> the purpose of it. Hence, add new device tree entry called
> 'qcom,ath10k-pre-calibration-data' to carry only pre calibration data.
>
> Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Applied, thanks.
--
Kalle Valo
_______________________________________________
ath10k mailing list
ath10k@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/ath10k
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH] dt: bindings: add new dt entry for pre calibration in qcom, ath10k.txt
@ 2016-03-23 12:07 ` Valo, Kalle
0 siblings, 0 replies; 12+ messages in thread
From: Valo, Kalle @ 2016-03-23 12:07 UTC (permalink / raw)
To: Raja Mani
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org,
linux-wireless-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
ath10k-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org
Raja Mani <rmani-Rm6X0d1/PG5y9aJCnZT0Uw@public.gmane.org> writes:
> There two things done in this patch,
>
> 1) Existing device tree entry 'qcom,ath10k-calibration-data' carries
> not only calibration data, it carries board specific data too.
> So, make appropriate update in doc.
>
> 2) ipq4019 wifi needs new devie tree entry to carry calibration
> data alone (called pre cal data, it doesn't include any other info).
> Using 'qcom,ath10k-calibration-data' for ipq4019 would alter
> the purpose of it. Hence, add new device tree entry called
> 'qcom,ath10k-pre-calibration-data' to carry only pre calibration data.
>
> Signed-off-by: Raja Mani <rmani-Rm6X0d1/PG5y9aJCnZT0Uw@public.gmane.org>
Applied, thanks.
--
Kalle Valo--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [PATCH] dt: bindings: add new dt entry for pre calibration in qcom, ath10k.txt
@ 2016-03-23 12:07 ` Valo, Kalle
0 siblings, 0 replies; 12+ messages in thread
From: Valo, Kalle @ 2016-03-23 12:07 UTC (permalink / raw)
To: Raja Mani
Cc: devicetree@vger.kernel.org, robh@kernel.org,
linux-wireless@vger.kernel.org, linux-kernel@vger.kernel.org,
ath10k@lists.infradead.org
Raja Mani <rmani@qti.qualcomm.com> writes:
> There two things done in this patch,
>
> 1) Existing device tree entry 'qcom,ath10k-calibration-data' carries
> not only calibration data, it carries board specific data too.
> So, make appropriate update in doc.
>
> 2) ipq4019 wifi needs new devie tree entry to carry calibration
> data alone (called pre cal data, it doesn't include any other info).
> Using 'qcom,ath10k-calibration-data' for ipq4019 would alter
> the purpose of it. Hence, add new device tree entry called
> 'qcom,ath10k-pre-calibration-data' to carry only pre calibration data.
>
> Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Applied, thanks.
--
Kalle Valo
^ permalink raw reply [flat|nested] 12+ messages in thread