From: Marc Zyngier <maz@kernel.org>
To: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Cc: Thomas Gleixner <tglx@linutronix.de>,
Rob Herring <robh+dt@kernel.org>,
Linus Walleij <linus.walleij@linaro.org>,
Geert Uytterhoeven <geert+renesas@glider.be>,
Magnus Damm <magnus.damm@gmail.com>,
Bartosz Golaszewski <bgolaszewski@baylibre.com>,
Philipp Zabel <p.zabel@pengutronix.de>,
devicetree@vger.kernel.org, linux-renesas-soc@vger.kernel.org,
linux-gpio@vger.kernel.org, linux-kernel@vger.kernel.org,
Prabhakar <prabhakar.csengg@gmail.com>,
Biju Das <biju.das.jz@bp.renesas.com>
Subject: Re: [RFC PATCH v3 2/7] irqchip: Add RZ/G2L IA55 Interrupt Controller driver
Date: Fri, 10 Dec 2021 14:37:44 +0000 [thread overview]
Message-ID: <87v8zwjzk7.wl-maz@kernel.org> (raw)
In-Reply-To: <20211110225808.16388-3-prabhakar.mahadev-lad.rj@bp.renesas.com>
On Wed, 10 Nov 2021 22:58:03 +0000,
Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com> wrote:
>
> Add a driver for the Renesas RZ/G2L Interrupt Controller.
>
> This supports external pins being used as interrupts. It supports
> one line for NMI, 8 external pins and 32 GPIO pins (out of 123)
> to be used as IRQ lines.
>
> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> ---
> drivers/irqchip/Kconfig | 8 +
> drivers/irqchip/Makefile | 1 +
> drivers/irqchip/irq-renesas-rzg2l.c | 465 ++++++++++++++++++++++++++++
> 3 files changed, 474 insertions(+)
> create mode 100644 drivers/irqchip/irq-renesas-rzg2l.c
>
> diff --git a/drivers/irqchip/Kconfig b/drivers/irqchip/Kconfig
> index 4d5924e9f766..79b8c9274fd7 100644
> --- a/drivers/irqchip/Kconfig
> +++ b/drivers/irqchip/Kconfig
> @@ -236,6 +236,14 @@ config RENESAS_RZA1_IRQC
> Enable support for the Renesas RZ/A1 Interrupt Controller, to use up
> to 8 external interrupts with configurable sense select.
>
> +config RENESAS_RZG2L_IRQC
> + bool "Renesas RZ/G2L IRQC support" if COMPILE_TEST
> + select GENERIC_IRQ_CHIP
> + select IRQ_DOMAIN_HIERARCHY
> + help
> + Enable support for the Renesas RZ/G2L Interrupt Controller for external
> + devices.
> +
> config SL28CPLD_INTC
> bool "Kontron sl28cpld IRQ controller"
> depends on MFD_SL28CPLD=y || COMPILE_TEST
> diff --git a/drivers/irqchip/Makefile b/drivers/irqchip/Makefile
> index f88cbf36a9d2..8017786fbdac 100644
> --- a/drivers/irqchip/Makefile
> +++ b/drivers/irqchip/Makefile
> @@ -51,6 +51,7 @@ obj-$(CONFIG_RDA_INTC) += irq-rda-intc.o
> obj-$(CONFIG_RENESAS_INTC_IRQPIN) += irq-renesas-intc-irqpin.o
> obj-$(CONFIG_RENESAS_IRQC) += irq-renesas-irqc.o
> obj-$(CONFIG_RENESAS_RZA1_IRQC) += irq-renesas-rza1.o
> +obj-$(CONFIG_RENESAS_RZG2L_IRQC) += irq-renesas-rzg2l.o
> obj-$(CONFIG_VERSATILE_FPGA_IRQ) += irq-versatile-fpga.o
> obj-$(CONFIG_ARCH_NSPIRE) += irq-zevio.o
> obj-$(CONFIG_ARCH_VT8500) += irq-vt8500.o
> diff --git a/drivers/irqchip/irq-renesas-rzg2l.c b/drivers/irqchip/irq-renesas-rzg2l.c
> new file mode 100644
> index 000000000000..4258b9752c3b
> --- /dev/null
> +++ b/drivers/irqchip/irq-renesas-rzg2l.c
> @@ -0,0 +1,465 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Renesas RZ/G2L IRQC Driver
> + *
> + * Copyright (C) 2021 Renesas Electronics Corporation.
> + *
> + * Author: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/err.h>
> +#include <linux/io.h>
> +#include <linux/irqchip.h>
> +#include <linux/irqdomain.h>
> +#include <linux/of_address.h>
> +#include <linux/reset.h>
> +
> +#define IRQC_IRQ_START 1
> +#define IRQC_IRQ_COUNT 8
> +#define IRQC_TINT_START 9
> +#define IRQC_TINT_COUNT 32
> +#define IRQC_NUM_IRQ 41
> +
> +#define ISCR 0x10
> +#define IITSR 0x14
> +#define TSCR 0x20
> +#define TITSR0 0x24
> +#define TITSR1 0x28
> +#define TITSR0_MAX_INT 16
> +#define TITSEL_WIDTH 0x2
> +#define TSSR(n) (0x30 + ((n) * 4))
> +#define TIEN BIT(7)
> +#define TSSEL_SHIFT(n) (8 * (n))
> +#define TSSEL_MASK GENMASK(7, 0)
> +#define IRQ_MASK 0x3
> +
> +#define TSSR_OFFSET(n) ((n) % 4)
> +#define TSSR_INDEX(n) ((n) / 4)
> +
> +#define TITSR_TITSEL_EDGE_RISING 0
> +#define TITSR_TITSEL_EDGE_FALLING 1
> +#define TITSR_TITSEL_LEVEL_HIGH 2
> +#define TITSR_TITSEL_LEVEL_LOW 3
> +
> +#define IITSR_IITSEL(n, sense) ((sense) << ((n) * 2))
> +#define IITSR_IITSEL_LEVEL_LOW 0
> +#define IITSR_IITSEL_EDGE_FALLING 1
> +#define IITSR_IITSEL_EDGE_RISING 2
> +#define IITSR_IITSEL_EDGE_BOTH 3
> +#define IITSR_IITSEL_MASK(n) IITSR_IITSEL((n), 3)
> +
> +#define TINT_EXTRACT_HWIRQ(x) ((x) & ~GENMASK(31, 16))
> +#define TINT_EXTRACT_GPIOINT(x) ((x) >> 16)
> +
> +struct rzg2l_irqc_priv {
> + void __iomem *base;
> + struct of_phandle_args map[IRQC_NUM_IRQ];
> +};
> +
> +struct rzg2l_irqc_chip_data {
> + int tint;
> +};
> +
> +static struct rzg2l_irqc_priv *irq_data_to_priv(struct irq_data *data)
> +{
> + return data->domain->host_data;
> +}
> +
> +static void rzg2l_irq_eoi(struct irq_data *d)
> +{
> + struct rzg2l_irqc_priv *priv = irq_data_to_priv(d);
> + unsigned int hw_irq = irqd_to_hwirq(d) - IRQC_IRQ_START;
> + u16 bit = BIT(hw_irq);
> + u32 reg;
> +
> + reg = readl_relaxed(priv->base + ISCR);
> + if (reg & bit)
> + writel_relaxed(GENMASK(IRQC_IRQ_COUNT - 1, 0) & ~bit,
> + priv->base + ISCR);
RMW of a shared register without locking. Is it safe?
> +
> + irq_chip_eoi_parent(d);
> +}
> +
> +static void rzg2l_tint_eoi(struct irq_data *d)
> +{
> + struct rzg2l_irqc_priv *priv = irq_data_to_priv(d);
> + unsigned int hw_irq = irqd_to_hwirq(d);
> + u32 bit = BIT(hw_irq - IRQC_TINT_START);
> + u32 reg;
> +
> + reg = readl_relaxed(priv->base + TSCR);
> + if (reg & bit)
> + writel_relaxed(GENMASK(IRQC_TINT_COUNT - 1, 0) & ~bit,
> + priv->base + TSCR);
Same question.
> +
> + irq_chip_eoi_parent(d);
> +}
> +
> +static void rzg2l_irqc_eoi(struct irq_data *d)
> +{
> + unsigned int hw_irq = irqd_to_hwirq(d);
> +
> + if (hw_irq >= IRQC_IRQ_START && hw_irq <= IRQC_IRQ_COUNT)
> + return rzg2l_irq_eoi(d);
> + else if (hw_irq >= IRQC_TINT_START && hw_irq <= IRQC_TINT_COUNT)
> + return rzg2l_tint_eoi(d);
> +}
> +
> +static void rzg2l_irqc_irq_disable(struct irq_data *d)
> +{
> + unsigned int hw_irq = irqd_to_hwirq(d);
> +
> + if (hw_irq >= IRQC_TINT_START && hw_irq <= IRQC_TINT_COUNT) {
> + struct rzg2l_irqc_priv *priv = irq_data_to_priv(d);
> + u32 offset = hw_irq - IRQC_TINT_START;
> + u32 tssr_offset = TSSR_OFFSET(offset);
> + u8 tssr_index = TSSR_INDEX(offset);
> + u32 reg;
> +
> + reg = readl_relaxed(priv->base + TSSR(tssr_index));
> + reg &= ~(TSSEL_MASK << tssr_offset);
> + writel_relaxed(reg, priv->base + TSSR(tssr_index));
And again.
> + }
> + irq_chip_disable_parent(d);
> +}
> +
> +static void rzg2l_irqc_irq_enable(struct irq_data *d)
> +{
> + unsigned int hw_irq = irqd_to_hwirq(d);
> +
> + if (hw_irq >= IRQC_TINT_START && hw_irq <= IRQC_TINT_COUNT) {
> + struct rzg2l_irqc_priv *priv = irq_data_to_priv(d);
> + struct rzg2l_irqc_chip_data *chip_data = d->chip_data;
> + u32 offset = hw_irq - IRQC_TINT_START;
> + u32 tssr_offset = TSSR_OFFSET(offset);
> + u8 tssr_index = TSSR_INDEX(offset);
> + u32 reg;
> +
> + reg = readl_relaxed(priv->base + TSSR(tssr_index));
> + reg |= (TIEN | chip_data->tint) << TSSEL_SHIFT(tssr_offset);
> + writel_relaxed(reg, priv->base + TSSR(tssr_index));
And here.
> + }
> + irq_chip_enable_parent(d);
> +}
> +
> +static int rzg2l_irq_set_type(struct irq_data *d, unsigned int type)
> +{
> + struct rzg2l_irqc_priv *priv = irq_data_to_priv(d);
> + unsigned int hw_irq = irqd_to_hwirq(d) - IRQC_IRQ_START;
> + u16 sense, tmp;
> +
> + switch (type & IRQ_TYPE_SENSE_MASK) {
> + case IRQ_TYPE_LEVEL_LOW:
> + sense = IITSR_IITSEL_LEVEL_LOW;
> + break;
> +
> + case IRQ_TYPE_EDGE_FALLING:
> + sense = IITSR_IITSEL_EDGE_FALLING;
> + break;
> +
> + case IRQ_TYPE_EDGE_RISING:
> + sense = IITSR_IITSEL_EDGE_RISING;
> + break;
> +
> + case IRQ_TYPE_EDGE_BOTH:
> + sense = IITSR_IITSEL_EDGE_BOTH;
> + break;
> +
> + default:
> + return -EINVAL;
> + }
> +
> + tmp = readl_relaxed(priv->base + IITSR);
> + tmp &= ~IITSR_IITSEL_MASK(hw_irq);
> + tmp |= IITSR_IITSEL(hw_irq, sense);
> + writel_relaxed(tmp, priv->base + IITSR);
It's everywhere. I'll stop mentioning it, but this driver is racy as
hell.
> +
> + return 0;
> +}
> +
> +static int rzg2l_tint_set_edge(struct irq_data *d, unsigned int type)
> +{
> + struct rzg2l_irqc_priv *priv = irq_data_to_priv(d);
> + unsigned int hwirq = irqd_to_hwirq(d);
> + u32 titseln = hwirq - IRQC_TINT_START;
> + u8 sense;
> + u32 reg;
> +
> + switch (type & IRQ_TYPE_SENSE_MASK) {
> + case IRQ_TYPE_EDGE_RISING:
> + sense = TITSR_TITSEL_EDGE_RISING;
> + break;
> +
> + case IRQ_TYPE_EDGE_FALLING:
> + sense = TITSR_TITSEL_EDGE_FALLING;
> + break;
> +
> + default:
> + return -EINVAL;
> + }
> +
> + if (titseln < TITSR0_MAX_INT) {
> + reg = readl_relaxed(priv->base + TITSR0);
> + reg &= ~(IRQ_MASK << (titseln * TITSEL_WIDTH));
> + reg |= sense << (titseln * TITSEL_WIDTH);
> + writel_relaxed(reg, priv->base + TITSR0);
> + } else {
> + titseln = titseln / TITSEL_WIDTH;
> + reg = readl_relaxed(priv->base + TITSR1);
> + reg &= ~(IRQ_MASK << (titseln * TITSEL_WIDTH));
> + reg |= sense << (titseln * TITSEL_WIDTH);
> + writel_relaxed(reg, priv->base + TITSR1);
> + }
Sight:
if (titseln < TITSR0_MAX_INT) {
r = TITSR0;
} else {
titseln /= TITSEL_WIDTH;
r = TITSR1;
}
reg = readl_relaxed(priv->base + r);
reg &= ~(IRQ_MASK << (titseln * TITSEL_WIDTH));
reg |= sense << (titseln * TITSEL_WIDTH);
writel_relaxed(reg, priv->base + r);
plus the missing locking.
> +
> + return 0;
> +}
> +
> +static int rzg2l_irqc_set_type(struct irq_data *d, unsigned int type)
> +{
> + unsigned int hw_irq = irqd_to_hwirq(d);
> +
> + if (hw_irq >= IRQC_IRQ_START && hw_irq <= IRQC_IRQ_COUNT)
> + return rzg2l_irq_set_type(d, type);
> + else if (hw_irq >= IRQC_TINT_START && hw_irq <= IRQC_TINT_COUNT)
> + return rzg2l_tint_set_edge(d, type);
> +
> + return -EINVAL;
> +}
> +
> +static struct irq_chip irqc_chip = {
> + .name = "rzg2l-irqc",
> + .irq_eoi = rzg2l_irqc_eoi,
> + .irq_mask = irq_chip_mask_parent,
> + .irq_unmask = irq_chip_unmask_parent,
> + .irq_disable = rzg2l_irqc_irq_disable,
> + .irq_enable = rzg2l_irqc_irq_enable,
> + .irq_get_irqchip_state = irq_chip_get_parent_state,
> + .irq_set_irqchip_state = irq_chip_set_parent_state,
> + .irq_retrigger = irq_chip_retrigger_hierarchy,
> + .irq_set_type = rzg2l_irqc_set_type,
> + .flags = IRQCHIP_MASK_ON_SUSPEND |
> + IRQCHIP_SET_TYPE_MASKED |
> + IRQCHIP_SKIP_SET_WAKE,
> +};
> +
> +static int rzg2l_irqc_alloc(struct irq_domain *domain, unsigned int virq,
> + unsigned int nr_irqs, void *arg)
> +{
> + struct rzg2l_irqc_priv *priv = domain->host_data;
> + struct rzg2l_irqc_chip_data *chip_data = NULL;
> + struct irq_fwspec spec;
> + irq_hw_number_t hwirq;
> + int tint = -EINVAL;
> + unsigned int type;
> + unsigned int i;
> + int ret;
> +
> + ret = irq_domain_translate_twocell(domain, arg, &hwirq, &type);
> + if (ret)
> + return ret;
> +
> + /*
> + * For TINIT interrupts ie where pinctrl driver is child of irqc domain
> + * the hwirq and TINT are encoded in fwspec->param[0].
> + * hwirq for TINIT range from 9-40, hwirq is embedded 0-15 bits and TINT
> + * from 16-31 bits. TINIT from the pinctrl drivers needs to be programmed
> + * in IRQC registers to enable a given gpio pin as interrupt.
> + */
> + if (hwirq > IRQC_IRQ_COUNT) {
> + tint = TINT_EXTRACT_GPIOINT(hwirq);
> + hwirq = TINT_EXTRACT_HWIRQ(hwirq);
> + }
> +
> + if (hwirq > (IRQC_NUM_IRQ - 1))
> + return -EINVAL;
> +
> + if (tint != -EINVAL && (hwirq < IRQC_TINT_START || hwirq > (IRQC_NUM_IRQ - 1)))
> + return -EINVAL;
> +
> + chip_data = kzalloc(sizeof(*chip_data), GFP_KERNEL);
> + if (!chip_data)
> + return -ENOMEM;
> + chip_data->tint = tint;
> +
> + ret = irq_domain_set_hwirq_and_chip(domain, virq, hwirq, &irqc_chip,
> + chip_data);
> + if (ret) {
> + kfree(chip_data);
> + return ret;
> + }
> +
> + spec.fwnode = domain->parent->fwnode;
> + spec.param_count = priv->map[hwirq].args_count;
> + for (i = 0; i < spec.param_count; i++)
> + spec.param[i] = priv->map[hwirq].args[i];
> +
> + ret = irq_domain_alloc_irqs_parent(domain, virq, nr_irqs, &spec);
> + if (ret)
> + kfree(chip_data);
> +
> + return ret;
> +}
> +
> +static void rzg2l_irqc_domain_free(struct irq_domain *domain, unsigned int virq,
> + unsigned int nr_irqs)
> +{
> + struct irq_data *d;
> +
> + d = irq_domain_get_irq_data(domain, virq);
> + if (d) {
> + struct rzg2l_irqc_chip_data *chip_data = d->chip_data;
> +
> + kfree(chip_data);
> + }
> + irq_domain_free_irqs_common(domain, virq, nr_irqs);
> +}
> +
> +static const struct irq_domain_ops rzg2l_irqc_domain_ops = {
> + .alloc = rzg2l_irqc_alloc,
> + .free = rzg2l_irqc_domain_free,
> + .translate = irq_domain_translate_twocell,
> +};
> +
> +static int rzg2l_irqc_parse_map(struct rzg2l_irqc_priv *priv,
> + struct device_node *np,
> + struct device_node *parent)
> +{
> + unsigned int imaplen, i, j, ret;
> + struct device_node *ipar;
> + const __be32 *imap;
> + u32 intsize;
> +
> + imap = of_get_property(np, "interrupt-map", &imaplen);
We talked about this one already.
M.
--
Without deviation from the norm, progress is not possible.
next prev parent reply other threads:[~2021-12-10 14:37 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-11-10 22:58 [RFC PATCH v3 0/7] Renesas RZ/G2L IRQC support Lad Prabhakar
2021-11-10 22:58 ` [RFC PATCH v3 1/7] dt-bindings: interrupt-controller: Add Renesas RZ/G2L Interrupt Controller Lad Prabhakar
2021-11-19 16:52 ` Rob Herring
2021-11-10 22:58 ` [RFC PATCH v3 2/7] irqchip: Add RZ/G2L IA55 Interrupt Controller driver Lad Prabhakar
2021-12-10 14:37 ` Marc Zyngier [this message]
2021-11-10 22:58 ` [RFC PATCH v3 3/7] soc: renesas: Enable IRQC driver for RZ/G2L Lad Prabhakar
2021-11-10 22:58 ` [RFC PATCH v3 4/7] gpio: gpiolib: Allow free() callback to be overridden Lad Prabhakar
2021-11-10 22:58 ` [RFC PATCH v3 5/7] gpio: gpiolib: Add ngirq member to struct gpio_irq_chip Lad Prabhakar
2021-11-11 20:52 ` Andy Shevchenko
2021-11-11 21:15 ` Lad, Prabhakar
2021-11-10 22:58 ` [RFC PATCH v3 6/7] pinctrl: renesas: pinctrl-rzg2l: Add IRQ domain to handle GPIO interrupt Lad Prabhakar
2021-11-10 22:58 ` [RFC PATCH v3 7/7] arm64: dts: renesas: r9a07g044: Add IRQC node to SoC DTSI Lad Prabhakar
2021-11-12 14:12 ` [RFC PATCH v3 0/7] Renesas RZ/G2L IRQC support Geert Uytterhoeven
2021-11-12 14:22 ` Lad, Prabhakar
2021-11-22 19:25 ` Lad, Prabhakar
2021-12-10 1:08 ` Lad, Prabhakar
2021-12-10 2:04 ` Linus Walleij
2021-12-10 9:37 ` Lad, Prabhakar
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=87v8zwjzk7.wl-maz@kernel.org \
--to=maz@kernel.org \
--cc=bgolaszewski@baylibre.com \
--cc=biju.das.jz@bp.renesas.com \
--cc=devicetree@vger.kernel.org \
--cc=geert+renesas@glider.be \
--cc=linus.walleij@linaro.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-renesas-soc@vger.kernel.org \
--cc=magnus.damm@gmail.com \
--cc=p.zabel@pengutronix.de \
--cc=prabhakar.csengg@gmail.com \
--cc=prabhakar.mahadev-lad.rj@bp.renesas.com \
--cc=robh+dt@kernel.org \
--cc=tglx@linutronix.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.