[PATCH 02/13] ARM: dts: imx6qdl: SolidRun: move AR8035 into microsom

[rmk+kernel@armlinux.org.uk (Russell King)]

As all SolidRun microsoms are fitted with an AR8035, it's pointless
having the ethernet support as a separate include file.  Move the
AR8035 support into the main imx6qdl-microsom file.

Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
---
 arch/arm/boot/dts/imx6q-h100.dts               |  1 -
 arch/arm/boot/dts/imx6qdl-cubox-i.dtsi         |  1 -
 arch/arm/boot/dts/imx6qdl-hummingboard.dtsi    |  1 -
 arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi | 99 --------------------------
 arch/arm/boot/dts/imx6qdl-microsom.dtsi        | 53 ++++++++++++++
 5 files changed, 53 insertions(+), 102 deletions(-)
 delete mode 100644 arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi

diff --git a/arch/arm/boot/dts/imx6q-h100.dts b/arch/arm/boot/dts/imx6q-h100.dts
index a3269f57df2b..bf5dfc9c8127 100644
--- a/arch/arm/boot/dts/imx6q-h100.dts
+++ b/arch/arm/boot/dts/imx6q-h100.dts
@@ -43,7 +43,6 @@
 
 #include "imx6q.dtsi"
 #include "imx6qdl-microsom.dtsi"
-#include "imx6qdl-microsom-ar8035.dtsi"
 
 / {
 	model = "Auvidea H100";
diff --git a/arch/arm/boot/dts/imx6qdl-cubox-i.dtsi b/arch/arm/boot/dts/imx6qdl-cubox-i.dtsi
index b20508237046..57ce2dbb6ad9 100644
--- a/arch/arm/boot/dts/imx6qdl-cubox-i.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-cubox-i.dtsi
@@ -39,7 +39,6 @@
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
 #include "imx6qdl-microsom.dtsi"
-#include "imx6qdl-microsom-ar8035.dtsi"
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/gpio/gpio.h>
 
diff --git a/arch/arm/boot/dts/imx6qdl-hummingboard.dtsi b/arch/arm/boot/dts/imx6qdl-hummingboard.dtsi
index 0a0a7e4b956b..afd981e9b5e3 100644
--- a/arch/arm/boot/dts/imx6qdl-hummingboard.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-hummingboard.dtsi
@@ -39,7 +39,6 @@
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
 #include "imx6qdl-microsom.dtsi"
-#include "imx6qdl-microsom-ar8035.dtsi"
 
 / {
 	chosen {
diff --git a/arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi b/arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi
deleted file mode 100644
index 900e8c781f91..000000000000
--- a/arch/arm/boot/dts/imx6qdl-microsom-ar8035.dtsi
+++ /dev/null
@@ -1,99 +0,0 @@
-/*
- * Copyright (C) 2013,2014 Russell King
- *
- * This describes the hookup for an AR8035 to the iMX6 on the SolidRun
- * MicroSOM.
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- *  a) This file is free software; you can redistribute it and/or
- *     modify it under the terms of the GNU General Public License
- *     version 2 as published by the Free Software Foundation.
- *
- *     This file is distributed in the hope that it will be useful,
- *     but WITHOUT ANY WARRANTY; without even the implied warranty of
- *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
- *     GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- *  b) Permission is hereby granted, free of charge, to any person
- *     obtaining a copy of this software and associated documentation
- *     files (the "Software"), to deal in the Software without
- *     restriction, including without limitation the rights to use,
- *     copy, modify, merge, publish, distribute, sublicense, and/or
- *     sell copies of the Software, and to permit persons to whom the
- *     Software is furnished to do so, subject to the following
- *     conditions:
- *
- *     The above copyright notice and this permission notice shall be
- *     included in all copies or substantial portions of the Software.
- *
- *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- *     OTHER DEALINGS IN THE SOFTWARE.
- */
-&fec {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_microsom_enet_ar8035>;
-	phy-mode = "rgmii";
-	phy-reset-duration = <2>;
-	phy-reset-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
-	status = "okay";
-};
-
-&iomuxc {
-	enet {
-		pinctrl_microsom_enet_ar8035: microsom-enet-ar8035 {
-			fsl,pins = <
-				MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b8b0
-				MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
-				/* AR8035 reset */
-				MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x130b0
-				/* AR8035 interrupt */
-				MX6QDL_PAD_DI0_PIN2__GPIO4_IO18		0x80000000
-				/* GPIO16 -> AR8035 25MHz */
-				MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0xc0000000
-				MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x80000000
-				MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
-				MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
-				MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
-				MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
-				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
-				/* AR8035 CLK_25M --> ENET_REF_CLK (V22) */
-				MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x0a0b1
-				/* AR8035 pin strapping: IO voltage: pull up */
-				MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
-				/* AR8035 pin strapping: PHYADDR#0: pull down */
-				MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x13030
-				/* AR8035 pin strapping: PHYADDR#1: pull down */
-				MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x13030
-				/* AR8035 pin strapping: MODE#1: pull up */
-				MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
-				/* AR8035 pin strapping: MODE#3: pull up */
-				MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
-				/* AR8035 pin strapping: MODE#0: pull down */
-				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x13030
-
-				/*
-				 * As the RMII pins are also connected to RGMII
-				 * so that an AR8030 can be placed, set these
-				 * to high-z with the same pulls as above.
-				 * Use the GPIO settings to avoid changing the
-				 * input select registers.
-				 */
-				MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25	0x03000
-				MX6QDL_PAD_ENET_RXD0__GPIO1_IO27	0x03000
-				MX6QDL_PAD_ENET_RXD1__GPIO1_IO26	0x03000
-			>;
-		};
-	};
-};
diff --git a/arch/arm/boot/dts/imx6qdl-microsom.dtsi b/arch/arm/boot/dts/imx6qdl-microsom.dtsi
index f7266ae2534c..c1541f2ecf3a 100644
--- a/arch/arm/boot/dts/imx6qdl-microsom.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-microsom.dtsi
@@ -69,6 +69,15 @@
 	};
 };
 
+&fec {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_microsom_enet_ar8035>;
+	phy-mode = "rgmii";
+	phy-reset-duration = <2>;
+	phy-reset-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
 &iomuxc {
 	microsom {
 		pinctrl_microsom_brcm_bt: microsom-brcm-bt {
@@ -100,6 +109,50 @@
 			>;
 		};
 
+		pinctrl_microsom_enet_ar8035: microsom-enet-ar8035 {
+			fsl,pins = <
+				MX6QDL_PAD_ENET_MDIO__ENET_MDIO		0x1b8b0
+				MX6QDL_PAD_ENET_MDC__ENET_MDC		0x1b0b0
+				/* AR8035 reset */
+				MX6QDL_PAD_KEY_ROW4__GPIO4_IO15		0x130b0
+				/* AR8035 interrupt */
+				MX6QDL_PAD_DI0_PIN2__GPIO4_IO18		0x80000000
+				/* GPIO16 -> AR8035 25MHz */
+				MX6QDL_PAD_GPIO_16__ENET_REF_CLK	0xc0000000
+				MX6QDL_PAD_RGMII_TXC__RGMII_TXC		0x80000000
+				MX6QDL_PAD_RGMII_TD0__RGMII_TD0		0x1b030
+				MX6QDL_PAD_RGMII_TD1__RGMII_TD1		0x1b030
+				MX6QDL_PAD_RGMII_TD2__RGMII_TD2		0x1b030
+				MX6QDL_PAD_RGMII_TD3__RGMII_TD3		0x1b030
+				MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL	0x1b030
+				/* AR8035 CLK_25M --> ENET_REF_CLK (V22) */
+				MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK	0x0a0b1
+				/* AR8035 pin strapping: IO voltage: pull up */
+				MX6QDL_PAD_RGMII_RXC__RGMII_RXC		0x1b030
+				/* AR8035 pin strapping: PHYADDR#0: pull down */
+				MX6QDL_PAD_RGMII_RD0__RGMII_RD0		0x13030
+				/* AR8035 pin strapping: PHYADDR#1: pull down */
+				MX6QDL_PAD_RGMII_RD1__RGMII_RD1		0x13030
+				/* AR8035 pin strapping: MODE#1: pull up */
+				MX6QDL_PAD_RGMII_RD2__RGMII_RD2		0x1b030
+				/* AR8035 pin strapping: MODE#3: pull up */
+				MX6QDL_PAD_RGMII_RD3__RGMII_RD3		0x1b030
+				/* AR8035 pin strapping: MODE#0: pull down */
+				MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL	0x13030
+
+				/*
+				 * As the RMII pins are also connected to RGMII
+				 * so that an AR8030 can be placed, set these
+				 * to high-z with the same pulls as above.
+				 * Use the GPIO settings to avoid changing the
+				 * input select registers.
+				 */
+				MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25	0x03000
+				MX6QDL_PAD_ENET_RXD0__GPIO1_IO27	0x03000
+				MX6QDL_PAD_ENET_RXD1__GPIO1_IO26	0x03000
+			>;
+		};
+
 		pinctrl_microsom_uart1: microsom-uart1 {
 			fsl,pins = <
 				MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA	0x1b0b1
-- 
2.7.4