Re: Intel AHCI ICH9R not detecting devices

["xerces8" <xerces8@butn.net>]

[-- Attachment #1: Type: text/plain, Size: 601 bytes --]

Tejun Heo wrote:

> xerces8 wrote:
> >> This looks like resource conflict to me, which could have resulted
> >> from ahci trying to grab all resources.  Can you please post the
> >> result of "cat /proc/ioports" and "cat /proc/iomem"?
> > 
> > I noticed that in IDE mode the same happens (32bit kernel has problems,
> > 64bit kernel has not), so here is dmesg, iomem and ioports for all 4
> > combinations.
> 
> Can you please try the attached debug patch and report boot log.  All
> resources look fine.

Hi!

(I was away during the week)

I run the patch and the result is attached.

Regards,
David

[-- Attachment #2: dmesg.debug --]
[-- Type: application/octet-stream, Size: 15427 bytes --]

r: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
checking if image is initramfs... it is
Freeing initrd memory: 75924k freed
highmem bounce pool size: 64 pages
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
fuse init (API version 7.9)
JFS: nTxBlock = 8192, nTxLock = 65536
SGI XFS with security attributes, realtime, large block numbers, no debug enabled
msgmni has been set to 1708
async_tx: api initialized (sync-only)
io scheduler noop registered
io scheduler anticipatory registered (default)
pci 0000:01:00.0: Boot video device
input: Power Button (FF) as /class/input/input0
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input1
ACPI: Power Button (CM) [PWRB]
ACPI: SSDT CFF8E0D0, 01D2 (r1    AMI   CPU1PM        1 INTL 20060113)
ACPI: ACPI0007:00 is registered as cooling_device0
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
floppy0: no floppy controllers found
brd: module loaded
loop: module loaded
Compaq SMART2 Driver (v 2.6.0)
HP CISS Driver (v 3.6.20)
Intel(R) PRO/1000 Network Driver - version 7.3.20-k2
Copyright (c) 1999-2006 Intel Corporation.
e1000e: Intel(R) PRO/1000 Network Driver - 0.3.3.3-k2
e1000e: Copyright (c) 1999-2008 Intel Corporation.
Intel(R) Gigabit Ethernet Network Driver - version 1.0.8-k2
Copyright (c) 2007 Intel Corporation.
ixgbe: Intel(R) 10 Gigabit PCI Express Network Driver - version 1.3.18-k2
ixgbe: Copyright (c) 1999-2007 Intel Corporation.
Intel(R) PRO/10GbE Network Driver - version 1.0.126-k4
Copyright (c) 1999-2006 Intel Corporation.
tehuti: Tehuti Networks(R) Network Driver, 7.29.3
tehuti: Options: hw_csum 
pcnet32.c:v1.35 21.Apr.2008 tsbogend@alpha.franken.de
e100: Intel(R) PRO/100 Network Driver, 3.5.23-k4-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
ThunderLAN driver v1.15
TLAN: 0 devices installed, PCI: 0  EISA: 0
ns83820.c: National Semiconductor DP83820 10/100/1000 driver.
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:02:00.0 to 64
sky2 0000:02:00.0: v1.21 addr 0xfe9fc000 irq 10 Yukon-EC Ultra (0xb4) rev 2
sky2 eth0: addr 00:1e:8c:07:41:53
cs89x0:cs89x0_probe(0x0)
PP_addr at 300[a]: 0xffff
eth1: incorrect signature at 300[c]: 0xffff!=0x630E
PP_addr at 320[a]: 0xffff
eth1: incorrect signature at 320[c]: 0xffff!=0x630E
PP_addr at 340[a]: 0xffff
eth1: incorrect signature at 340[c]: 0xffff!=0x630E
PP_addr at 360[a]: 0xffff
eth1: incorrect signature at 360[c]: 0xffff!=0x630E
PP_addr at 200[a]: 0xffff
eth1: incorrect signature at 200[c]: 0xffff!=0x630E
PP_addr at 220[a]: 0xffff
eth1: incorrect signature at 220[c]: 0xffff!=0x630E
PP_addr at 240[a]: 0xffff
eth1: incorrect signature at 240[c]: 0xffff!=0x630E
PP_addr at 260[a]: 0xffff
eth1: incorrect signature at 260[c]: 0xffff!=0x630E
PP_addr at 280[a]: 0xffff
eth1: incorrect signature at 280[c]: 0xffff!=0x630E
PP_addr at 2a0[a]: 0xffff
eth1: incorrect signature at 2a0[c]: 0xffff!=0x630E
PP_addr at 2c0[a]: 0xffff
eth1: incorrect signature at 2c0[c]: 0xffff!=0x630E
PP_addr at 2e0[a]: 0xffff
eth1: incorrect signature at 2e0[c]: 0xffff!=0x630E
cs89x0: no cs8900 or cs8920 detected.  Be sure to disable PnP with SETUP
Silan SC92031 PCI Fast Ethernet Adapter driver 2.0c
eth%d: i82596 initialization timed out
dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)
winbond-840.c:v1.01-e (2.4 port) Sep-11-2006  Donald Becker <becker@scyld.com>
  http://www.scyld.com/network/drivers.html
uli526x: ULi M5261/M5263 net driver, version 0.9.3 (2005-7-29)
Uniform Multi-Platform E-IDE driver
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide_generic: please use "probe_mask=0x3f" module parameter for probing all legacy ISA IDE ports
Probing IDE interface ide0...
Probing IDE interface ide1...
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
ide-floppy driver 1.00
Loading Adaptec I2O RAID: Version 2.4 Build 5go
Detecting Adaptec I2O RAID controllers...
Adaptec aacraid driver 1.1-5[2456]-ms
aic94xx: Adaptec aic94xx SAS/SATA driver version 1.0.3 loaded
scsi: <fdomain> Detection failed (no card)
Emulex LightPulse Fibre Channel SCSI driver 8.2.6
Copyright(c) 2004-2008 Emulex.  All rights reserved.
Failed initialization of WD-7000 SCSI card!
megaraid cmm: 2.20.2.7 (Release Date: Sun Jul 16 00:01:03 EST 2006)
megaraid: 2.20.5.1 (Release Date: Thu Nov 16 15:32:35 EST 2006)
megasas: 00.00.03.20-rc1 Mon. March 10 11:02:31 PDT 2008
GDT-HA: Storage RAID Controller Driver. Version: 3.05
3ware Storage Controller device driver for Linux v1.26.02.002.
3ware 9000 Storage Controller device driver for Linux v2.26.02.010.
RocketRAID 3xxx/4xxx Controller driver v1.3 (071203)
st: Version 20080224, fixed bufsize 32768, s/g segs 256
Driver 'st' needs updating - please use bus_type methods
osst :I: Tape driver with OnStream support version 0.99.4
osst :I: $Id: osst.c,v 1.73 2005/01/01 21:13:34 wriede Exp $
Driver 'osst' needs updating - please use bus_type methods
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
ahci 0000:00:1f.2: version 3.0
ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 15
PCI: setting IRQ 15 as level-triggered
ACPI: PCI Interrupt 0000:00:1f.2[B] -> Link [LNKG] -> GSI 15 (level, low) -> IRQ 15
ahci 0000:00:1f.2: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl SATA mode
ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pmp pio slum part 
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ahci 0000:00:1f.2: ahci_host_activate() failed -16
ACPI: PCI interrupt for device 0000:00:1f.2 disabled
ahci: probe of 0000:00:1f.2 failed with error -16
ACPI: PCI Interrupt 0000:03:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
ahci 0000:03:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
ahci 0000:03:00.0: flags: 64bit ncq pm led clo pmp pio slum part 
PCI: Setting latency timer of device 0000:03:00.0 to 64
scsi2 : ahci
scsi3 : ahci
ata1: SATA max UDMA/133 abar m8192@0xfeafe000 port 0xfeafe100 irq 11
ata2: SATA max UDMA/133 abar m8192@0xfeafe000 port 0xfeafe180 irq 11
ata1: SATA link down (SStatus 0 SControl 300)
ata2: SATA link down (SStatus 0 SControl 300)
ACPI: PCI Interrupt 0000:03:00.1[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:03:00.1 to 64
scsi4 : pata_jmicron
scsi5 : pata_jmicron
ata3: PATA max UDMA/100 cmd 0xec00 ctl 0xe880 bmdma 0xe400 irq 10
ata4: PATA max UDMA/100 cmd 0xe800 ctl 0xe480 bmdma 0xe408 irq 10
Fusion MPT base driver 3.04.06
Copyright (c) 1999-2007 LSI Corporation
Fusion MPT SPI Host driver 3.04.06
Fusion MPT FC Host driver 3.04.06
Fusion MPT SAS Host driver 3.04.06
Fusion MPT misc device (ioctl) driver 3.04.06
mptctl: Registered with Fusion MPT base driver
mptctl: /dev/mptctl @ (major,minor=10,220)
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 14
PCI: setting IRQ 14 as level-triggered
ACPI: PCI Interrupt 0000:05:03.0[A] -> Link [LNKD] -> GSI 14 (level, low) -> IRQ 14
ohci1394: Failed to allocate interrupt 14
ohci1394: probe of 0000:05:03.0 failed with error -12
ieee1394: raw1394: /dev/raw1394 device initialized
eth1394: Cannot register CSR space
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:1a.7[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:1a.7 to 64
ehci_hcd 0000:00:1a.7: EHCI Host Controller
ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1a.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1a.7
ehci_hcd 0000:00:1a.7: irq 5, io mem 0xf9fffc00
ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 7
PCI: setting IRQ 7 as level-triggered
ACPI: PCI Interrupt 0000:00:1d.7[A] -> Link [LNKH] -> GSI 7 (level, low) -> IRQ 7
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 7, io mem 0xf9fff800
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 6 ports detected
116x: driver isp116x-hcd, 03 Nov 2005
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:00:1a.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1a.0 to 64
uhci_hcd 0000:00:1a.0: UHCI Host Controller
uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1a.0: irq 11, io base 0x0000b800
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 3
PCI: setting IRQ 3 as level-triggered
ACPI: PCI Interrupt 0000:00:1a.1[B] -> Link [LNKF] -> GSI 3 (level, low) -> IRQ 3
PCI: Setting latency timer of device 0000:00:1a.1 to 64
uhci_hcd 0000:00:1a.1: UHCI Host Controller
uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1a.1: irq 3, io base 0x0000b880
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 1-3: new high speed USB device using ehci_hcd and address 2
ACPI: PCI Interrupt 0000:00:1a.2[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:1a.2 to 64
uhci_hcd 0000:00:1a.2: UHCI Host Controller
uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
uhci_hcd 0000:00:1a.2: irq 5, io base 0x0000bc00
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
usb 1-3: configuration #1 chosen from 1 choice
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKH] -> GSI 7 (level, low) -> IRQ 7
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
uhci_hcd 0000:00:1d.0: irq 7, io base 0x0000b080
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 14 (level, low) -> IRQ 14
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
uhci_hcd 0000:00:1d.1: request interrupt 14 failed
uhci_hcd 0000:00:1d.1: USB bus 7 deregistered
ACPI: PCI interrupt for device 0000:00:1d.1 disabled
uhci_hcd 0000:00:1d.1: init 0000:00:1d.1 fail, -16
uhci_hcd: probe of 0000:00:1d.1 failed with error -16
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 7
uhci_hcd 0000:00:1d.2: irq 5, io base 0x0000b480
usb usb7: configuration #1 chosen from 1 choice
hub 7-0:1.0: USB hub found
hub 7-0:1.0: 2 ports detected
usb 2-2: new high speed USB device using ehci_hcd and address 2
sl811: driver sl811-hcd, 19 May 2005
usb 2-2: configuration #1 chosen from 1 choice
usb 7-1: new low speed USB device using uhci_hcd and address 2
usb 7-1: configuration #1 chosen from 1 choice
usb 7-2: new low speed USB device using uhci_hcd and address 3
usb 7-2: configuration #1 chosen from 1 choice
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
scsi6 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usblcd
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
md: linear personality registered for level -1
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
md: raid10 personality registered for level 10
raid6: int32x1    960 MB/s
raid6: int32x2    906 MB/s
raid6: int32x4    780 MB/s
raid6: int32x8    702 MB/s
raid6: mmxx1     3093 MB/s
raid6: mmxx2     3535 MB/s
raid6: sse1x1    2108 MB/s
raid6: sse1x2    2728 MB/s
raid6: sse2x1    3768 MB/s
raid6: sse2x2    4307 MB/s
raid6: using algorithm sse2x2 (4307 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: multipath personality registered for level -4
device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
device-mapper: multipath: version 1.0.5 loaded
device-mapper: multipath round-robin: version 1.0.0 loaded
device-mapper: multipath emc: version 0.0.3 loaded
cpuidle: using governor ladder
sdhci: Secure Digital Host Controller Interface driver
sdhci: Copyright(c) Pierre Ossman
wbsd: Winbond W83L51xD SD/MMC card interface driver
wbsd: Copyright(c) Pierre Ossman
padlock: VIA PadLock not detected.
usbcore: registered new interface driver hiddev
input: CHICONY USB Keyboard as /class/input/input2
input: USB HID v1.10 Keyboard [CHICONY USB Keyboard] on usb-0000:00:1d.2-1
input: CHESEN PS2 to USB Converter as /class/input/input3
input: USB HID v1.10 Keyboard [CHESEN PS2 to USB Converter] on usb-0000:00:1d.2-2
input: CHESEN PS2 to USB Converter as /class/input/input4
input: USB HID v1.10 Mouse [CHESEN PS2 to USB Converter] on usb-0000:00:1d.2-2
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
TCP cubic registered
NET: Registered protocol family 17
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
Using IPI Shortcut mode
BIOS EDD facility v0.16 2004-Jun-25, 6 devices found
Freeing unused kernel memory: 300k freed
scsi 6:0:0:0: Direct-Access     SanDisk  U3 Titanium      2.18 PQ: 0 ANSI: 2
sd 6:0:0:0: [sda] 2006673 512-byte hardware sectors (1027 MB)
sd 6:0:0:0: [sda] Write Protect is off
sd 6:0:0:0: [sda] Mode Sense: 03 00 00 00
sd 6:0:0:0: [sda] Assuming drive cache: write through
sd 6:0:0:0: [sda] 2006673 512-byte hardware sectors (1027 MB)
sd 6:0:0:0: [sda] Write Protect is off
sd 6:0:0:0: [sda] Mode Sense: 03 00 00 00
sd 6:0:0:0: [sda] Assuming drive cache: write through
 sda: sda1
sd 6:0:0:0: [sda] Attached SCSI removable disk
sd 6:0:0:0: Attached scsi generic sg0 type 0
usb-storage: device scan complete