Re: r8a77950-salvator-x does nto boot since cfa7ede20f133cc81cef01dc3a516dda3a9721ee arm64: set TEXT_OFFSET to 0x0 in preparation for removing it entirely

[Corentin Labbe <clabbe.montjoie@gmail.com>]

Le Tue, Jan 05, 2021 at 11:13:03AM +0100, Geert Uytterhoeven a écrit :
> Hi Corentin,
> 
> On Tue, Jan 5, 2021 at 10:52 AM Corentin Labbe
> <clabbe.montjoie@gmail.com> wrote:
> > Due to DTB renaming, salvatorX was not booted since a long time in kernelCI.
> > Now the rename is handled, the board fail to boot.
> >
> > I have bisected the problem:
> 
> > # first bad commit: [cfa7ede20f133cc81cef01dc3a516dda3a9721ee] arm64: set TEXT_OFFSET to 0x0 in preparation for removing it entirely
> >
> > This is the interesting part of uboot log:
> > [    0.000292] NOTI[    0.000292] NOTICE:  BL2: R-Car Gen3 Initial Program Loader(CA57) Rev.1.0.16
> > [    0.005855] NOTICE:  BL2: PRR is R-Car H3 Ver1.1
> > [    0.010437] NOTICE:  BL2: Board is Salvator-X Rev1.0
> > [    0.015379] NOTICE:  BL2: Boot device is HyperFlash(80MHz)
> > [    0.020804] NOTICE:  BL2: LCM state is CM
> > [    0.024847] NOTICE:  BL2: AVS setting succeeded. DVFS_SetVID=0x53
> > [    0.030891] NOTICE:  BL2: DDR1600(rev.0.27)NOTICE:  [COLD_BOOT]NOTICE:  ..0
> > [    0.066311] NOTICE:  BL2: DRAM Split is 4ch
> > [    0.070195] NOTICE:  BL2: QoS is default setting(rev.0.37)
> > [    0.075697] NOTICE:  BL2: Lossy Decomp areas
> > [    0.079872] NOTICE:       Entry 0: DCMPAREACRAx:0x80000540 DCMPAREACRBx:0x570
> > [    0.086957] NOTICE:       Entry 1: DCMPAREACRAx:0x40000000 DCMPAREACRBx:0x0
> > [    0.093869] NOTICE:       Entry 2: DCMPAREACRAx:0x20000000 DCMPAREACRBx:0x0
> > [    0.100785] NOTICE:  BL2: v1.3(release):b330e0e
> > [    0.105274] NOTICE:  BL2: Built : 15:26:51, Dec  6 2017
> > [    0.110462] NOTICE:  BL2: Normal boot
> > [    0.114103] NOTICE:  BL2: dst=0xe6320208 src=0x8180000 len=512(0x200)
> > [    0.120652] NOTICE:  BL2: dst=0x43f00000 src=0x8180400 len=6144(0x1800)
> > [    0.127110] NOTICE:  BL2: dst=0x44000000 src=0x81c0000 len=65536(0x10000)
> > [    0.134336] NOTICE:  BL2: dst=0x44100000 src=0x8200000 len=524288(0x80000)
> > [    0.144816] NOTICE:  BL2: dst=0x50000000 src=0x8640000 len=1048576(0x100000)
> > U-Boot 2015.04 (Dec 06 2017 - 15:26:59)
> > CPU: Renesas Electronics R8A7795 rev 1.1
> > Board: Salvator-X
> > I2C:   ready
> > DRAM:  3.9 GiB
> > MMC:   sh-sdhi: 0, sh-sdhi: 1, sh-sdhi: 2
> > In:    serial
> > Out:   serial
> > Err:   serial
> > Net:   ravb
> >
> > [...]
> >
> > booti 0x48080000 0x4a000000 0x48000000
>              ^^^^^
> I take it this is the problem?
> 
> For R-Car H3 ES1.0, I currently use the addresses below:
> 
>     tftpboot 0x60000000 h3-salvator-x/Image
>     tftpboot 0x68000000 h3-salvator-x/r8a77950-salvator-x.dtb
>     booti 0x60000000 - 0x68000000
> 
> For R-Car H3 ES2.0 (and other R-Car Gen3 SoCs), I use other addresses:
> 
>     tftpboot 0x50000000 h3-salvator-xs/Image
>     tftpboot 0x58000000 h3-salvator-xs/r8a77951-salvator-xs.dtb
>     booti 0x50000000 - 0x58000000
> 
> The firmware on your H3 ES1.1 board (Rev.1.0.16) is newer than on my
> ES1.0 board (Rev.1.0.12), so it's possible the second version works on
> your board, too.
> 
> If these work for you, I'll update https://elinux.org/R-Car/Boards/Salvator-X[S]
> 

Hello

Thanks, changing kernel/dtb address made it boot.
when testing, I have also discovered that r8a7796-m3ulcb hit the same issue than the salvatorX and that thoses address made it boot.

Regards