* [RESEND v4 PATCH 0/1] arm64: dts: mt8195: Add Ethernet controller
@ 2022-12-21 2:25 ` Biao Huang
0 siblings, 0 replies; 12+ messages in thread
From: Biao Huang @ 2022-12-21 2:25 UTC (permalink / raw)
To: AngeloGioacchino Del Regno, Rob Herring, Krzysztof Kozlowski,
Matthias Brugger
Cc: devicetree, linux-arm-kernel, linux-mediatek, linux-kernel,
Biao Huang, macpaul.lin
Resend v4, please review it, thanks~
Changes in v4:
1. remove {address,size}-cells = <0> to avoid warning as Angelo's feedback.
2. Add reviewd-by as Angelo's comments.
Changes in v3:
1. move stmmac-axi-config, rx-queues-config, tx-queues-configs inside ethernet node
as Angelo's comments.
2. add {address,size}-cells = <0> in ethernet node as Angelo's comments.
Changes in v2:
1. modify pinctrl node used by ethernet to match rules in pinctrl-mt8195.yaml,
which is pointed by Krzysztof.
2. remove "mac-address" property in ethernet node as comments of Krzysztof.
Changes in v1:
add dts node for MT8195 Ethernet controller
Biao Huang (1):
arm64: dts: mt8195: Add Ethernet controller
arch/arm64/boot/dts/mediatek/mt8195-demo.dts | 88 ++++++++++++++++++++
arch/arm64/boot/dts/mediatek/mt8195.dtsi | 86 +++++++++++++++++++
2 files changed, 174 insertions(+)
--
2.18.0
^ permalink raw reply [flat|nested] 12+ messages in thread* [RESEND v4 PATCH 0/1] arm64: dts: mt8195: Add Ethernet controller @ 2022-12-21 2:25 ` Biao Huang 0 siblings, 0 replies; 12+ messages in thread From: Biao Huang @ 2022-12-21 2:25 UTC (permalink / raw) To: AngeloGioacchino Del Regno, Rob Herring, Krzysztof Kozlowski, Matthias Brugger Cc: devicetree, linux-arm-kernel, linux-mediatek, linux-kernel, Biao Huang, macpaul.lin Resend v4, please review it, thanks~ Changes in v4: 1. remove {address,size}-cells = <0> to avoid warning as Angelo's feedback. 2. Add reviewd-by as Angelo's comments. Changes in v3: 1. move stmmac-axi-config, rx-queues-config, tx-queues-configs inside ethernet node as Angelo's comments. 2. add {address,size}-cells = <0> in ethernet node as Angelo's comments. Changes in v2: 1. modify pinctrl node used by ethernet to match rules in pinctrl-mt8195.yaml, which is pointed by Krzysztof. 2. remove "mac-address" property in ethernet node as comments of Krzysztof. Changes in v1: add dts node for MT8195 Ethernet controller Biao Huang (1): arm64: dts: mt8195: Add Ethernet controller arch/arm64/boot/dts/mediatek/mt8195-demo.dts | 88 ++++++++++++++++++++ arch/arm64/boot/dts/mediatek/mt8195.dtsi | 86 +++++++++++++++++++ 2 files changed, 174 insertions(+) -- 2.18.0 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 12+ messages in thread
* [RESEND PATCH v4] arm64: dts: mt8195: Add Ethernet controller 2022-12-21 2:25 ` Biao Huang @ 2022-12-21 2:25 ` Biao Huang -1 siblings, 0 replies; 12+ messages in thread From: Biao Huang @ 2022-12-21 2:25 UTC (permalink / raw) To: AngeloGioacchino Del Regno, Rob Herring, Krzysztof Kozlowski, Matthias Brugger Cc: devicetree, linux-arm-kernel, linux-mediatek, linux-kernel, Biao Huang, macpaul.lin Add Ethernet controller node for mt8195. Signed-off-by: Biao Huang <biao.huang@mediatek.com> --- arch/arm64/boot/dts/mediatek/mt8195-demo.dts | 88 ++++++++++++++++++++ arch/arm64/boot/dts/mediatek/mt8195.dtsi | 86 +++++++++++++++++++ 2 files changed, 174 insertions(+) diff --git a/arch/arm64/boot/dts/mediatek/mt8195-demo.dts b/arch/arm64/boot/dts/mediatek/mt8195-demo.dts index 4fbd99eb496a..0e8496d837ef 100644 --- a/arch/arm64/boot/dts/mediatek/mt8195-demo.dts +++ b/arch/arm64/boot/dts/mediatek/mt8195-demo.dts @@ -258,6 +258,72 @@ &mt6359_vsram_others_ldo_reg { }; &pio { + eth_default_pins: eth-default-pins { + pins-txd { + pinmux = <PINMUX_GPIO77__FUNC_GBE_TXD3>, + <PINMUX_GPIO78__FUNC_GBE_TXD2>, + <PINMUX_GPIO79__FUNC_GBE_TXD1>, + <PINMUX_GPIO80__FUNC_GBE_TXD0>; + drive-strength = <MTK_DRIVE_8mA>; + }; + pins-cc { + pinmux = <PINMUX_GPIO85__FUNC_GBE_TXC>, + <PINMUX_GPIO88__FUNC_GBE_TXEN>, + <PINMUX_GPIO87__FUNC_GBE_RXDV>, + <PINMUX_GPIO86__FUNC_GBE_RXC>; + drive-strength = <MTK_DRIVE_8mA>; + }; + pins-rxd { + pinmux = <PINMUX_GPIO81__FUNC_GBE_RXD3>, + <PINMUX_GPIO82__FUNC_GBE_RXD2>, + <PINMUX_GPIO83__FUNC_GBE_RXD1>, + <PINMUX_GPIO84__FUNC_GBE_RXD0>; + }; + pins-mdio { + pinmux = <PINMUX_GPIO89__FUNC_GBE_MDC>, + <PINMUX_GPIO90__FUNC_GBE_MDIO>; + input-enable; + }; + pins-power { + pinmux = <PINMUX_GPIO91__FUNC_GPIO91>, + <PINMUX_GPIO92__FUNC_GPIO92>; + output-high; + }; + }; + + eth_sleep_pins: eth-sleep-pins { + pins-txd { + pinmux = <PINMUX_GPIO77__FUNC_GPIO77>, + <PINMUX_GPIO78__FUNC_GPIO78>, + <PINMUX_GPIO79__FUNC_GPIO79>, + <PINMUX_GPIO80__FUNC_GPIO80>; + }; + pins-cc { + pinmux = <PINMUX_GPIO85__FUNC_GPIO85>, + <PINMUX_GPIO88__FUNC_GPIO88>, + <PINMUX_GPIO87__FUNC_GPIO87>, + <PINMUX_GPIO86__FUNC_GPIO86>; + }; + pins-rxd { + pinmux = <PINMUX_GPIO81__FUNC_GPIO81>, + <PINMUX_GPIO82__FUNC_GPIO82>, + <PINMUX_GPIO83__FUNC_GPIO83>, + <PINMUX_GPIO84__FUNC_GPIO84>; + }; + pins-mdio { + pinmux = <PINMUX_GPIO89__FUNC_GPIO89>, + <PINMUX_GPIO90__FUNC_GPIO90>; + input-disable; + bias-disable; + }; + pins-power { + pinmux = <PINMUX_GPIO91__FUNC_GPIO91>, + <PINMUX_GPIO92__FUNC_GPIO92>; + input-disable; + bias-disable; + }; + }; + gpio_keys_pins: gpio-keys-pins { pins { pinmux = <PINMUX_GPIO106__FUNC_GPIO106>; @@ -434,6 +500,28 @@ &xhci0 { status = "okay"; }; +ð { + phy-mode ="rgmii-rxid"; + phy-handle = <ðernet_phy0>; + snps,reset-gpio = <&pio 93 GPIO_ACTIVE_HIGH>; + snps,reset-delays-us = <0 10000 10000>; + mediatek,tx-delay-ps = <2030>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <ð_default_pins>; + pinctrl-1 = <ð_sleep_pins>; + status = "okay"; + + mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + ethernet_phy0: ethernet-phy@1 { + compatible = "ethernet-phy-id001c.c916"; + reg = <0x1>; + }; + }; +}; + &xhci1 { vusb33-supply = <&mt6359_vusb_ldo_reg>; status = "okay"; diff --git a/arch/arm64/boot/dts/mediatek/mt8195.dtsi b/arch/arm64/boot/dts/mediatek/mt8195.dtsi index 5d31536f4c48..02112bbf2bdf 100644 --- a/arch/arm64/boot/dts/mediatek/mt8195.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt8195.dtsi @@ -1046,6 +1046,92 @@ spis1: spi@1101e000 { status = "disabled"; }; + eth: ethernet@11021000 { + compatible = "mediatek,mt8195-gmac", "snps,dwmac-5.10a"; + reg = <0 0x11021000 0 0x4000>; + interrupts = <GIC_SPI 716 IRQ_TYPE_LEVEL_HIGH 0>; + interrupt-names = "macirq"; + clock-names = "axi", + "apb", + "mac_cg", + "mac_main", + "ptp_ref", + "rmii_internal"; + clocks = <&pericfg_ao CLK_PERI_AO_ETHERNET>, + <&pericfg_ao CLK_PERI_AO_ETHERNET_BUS>, + <&pericfg_ao CLK_PERI_AO_ETHERNET_MAC>, + <&topckgen CLK_TOP_SNPS_ETH_250M>, + <&topckgen CLK_TOP_SNPS_ETH_62P4M_PTP>, + <&topckgen CLK_TOP_SNPS_ETH_50M_RMII>; + assigned-clocks = <&topckgen CLK_TOP_SNPS_ETH_250M>, + <&topckgen CLK_TOP_SNPS_ETH_62P4M_PTP>, + <&topckgen CLK_TOP_SNPS_ETH_50M_RMII>; + assigned-clock-parents = <&topckgen CLK_TOP_ETHPLL_D2>, + <&topckgen CLK_TOP_ETHPLL_D8>, + <&topckgen CLK_TOP_ETHPLL_D10>; + power-domains = <&spm MT8195_POWER_DOMAIN_ETHER>; + mediatek,pericfg = <&infracfg_ao>; + snps,axi-config = <&stmmac_axi_setup>; + snps,mtl-rx-config = <&mtl_rx_setup>; + snps,mtl-tx-config = <&mtl_tx_setup>; + snps,txpbl = <16>; + snps,rxpbl = <16>; + snps,clk-csr = <0>; + status = "disabled"; + + stmmac_axi_setup: stmmac-axi-config { + snps,wr_osr_lmt = <0x7>; + snps,rd_osr_lmt = <0x7>; + snps,blen = <0 0 0 0 16 8 4>; + }; + + mtl_rx_setup: rx-queues-config { + snps,rx-queues-to-use = <4>; + snps,rx-sched-sp; + queue0 { + snps,dcb-algorithm; + snps,map-to-dma-channel = <0x0>; + }; + queue1 { + snps,dcb-algorithm; + snps,map-to-dma-channel = <0x0>; + }; + queue2 { + snps,dcb-algorithm; + snps,map-to-dma-channel = <0x0>; + }; + queue3 { + snps,dcb-algorithm; + snps,map-to-dma-channel = <0x0>; + }; + }; + + mtl_tx_setup: tx-queues-config { + snps,tx-queues-to-use = <4>; + snps,tx-sched-wrr; + queue0 { + snps,weight = <0x10>; + snps,dcb-algorithm; + snps,priority = <0x0>; + }; + queue1 { + snps,weight = <0x11>; + snps,dcb-algorithm; + snps,priority = <0x1>; + }; + queue2 { + snps,weight = <0x12>; + snps,dcb-algorithm; + snps,priority = <0x2>; + }; + queue3 { + snps,weight = <0x13>; + snps,dcb-algorithm; + snps,priority = <0x3>; + }; + }; + }; + xhci0: usb@11200000 { compatible = "mediatek,mt8195-xhci", "mediatek,mtk-xhci"; -- 2.25.1 ^ permalink raw reply related [flat|nested] 12+ messages in thread
* [RESEND PATCH v4] arm64: dts: mt8195: Add Ethernet controller @ 2022-12-21 2:25 ` Biao Huang 0 siblings, 0 replies; 12+ messages in thread From: Biao Huang @ 2022-12-21 2:25 UTC (permalink / raw) To: AngeloGioacchino Del Regno, Rob Herring, Krzysztof Kozlowski, Matthias Brugger Cc: devicetree, linux-arm-kernel, linux-mediatek, linux-kernel, Biao Huang, macpaul.lin Add Ethernet controller node for mt8195. Signed-off-by: Biao Huang <biao.huang@mediatek.com> --- arch/arm64/boot/dts/mediatek/mt8195-demo.dts | 88 ++++++++++++++++++++ arch/arm64/boot/dts/mediatek/mt8195.dtsi | 86 +++++++++++++++++++ 2 files changed, 174 insertions(+) diff --git a/arch/arm64/boot/dts/mediatek/mt8195-demo.dts b/arch/arm64/boot/dts/mediatek/mt8195-demo.dts index 4fbd99eb496a..0e8496d837ef 100644 --- a/arch/arm64/boot/dts/mediatek/mt8195-demo.dts +++ b/arch/arm64/boot/dts/mediatek/mt8195-demo.dts @@ -258,6 +258,72 @@ &mt6359_vsram_others_ldo_reg { }; &pio { + eth_default_pins: eth-default-pins { + pins-txd { + pinmux = <PINMUX_GPIO77__FUNC_GBE_TXD3>, + <PINMUX_GPIO78__FUNC_GBE_TXD2>, + <PINMUX_GPIO79__FUNC_GBE_TXD1>, + <PINMUX_GPIO80__FUNC_GBE_TXD0>; + drive-strength = <MTK_DRIVE_8mA>; + }; + pins-cc { + pinmux = <PINMUX_GPIO85__FUNC_GBE_TXC>, + <PINMUX_GPIO88__FUNC_GBE_TXEN>, + <PINMUX_GPIO87__FUNC_GBE_RXDV>, + <PINMUX_GPIO86__FUNC_GBE_RXC>; + drive-strength = <MTK_DRIVE_8mA>; + }; + pins-rxd { + pinmux = <PINMUX_GPIO81__FUNC_GBE_RXD3>, + <PINMUX_GPIO82__FUNC_GBE_RXD2>, + <PINMUX_GPIO83__FUNC_GBE_RXD1>, + <PINMUX_GPIO84__FUNC_GBE_RXD0>; + }; + pins-mdio { + pinmux = <PINMUX_GPIO89__FUNC_GBE_MDC>, + <PINMUX_GPIO90__FUNC_GBE_MDIO>; + input-enable; + }; + pins-power { + pinmux = <PINMUX_GPIO91__FUNC_GPIO91>, + <PINMUX_GPIO92__FUNC_GPIO92>; + output-high; + }; + }; + + eth_sleep_pins: eth-sleep-pins { + pins-txd { + pinmux = <PINMUX_GPIO77__FUNC_GPIO77>, + <PINMUX_GPIO78__FUNC_GPIO78>, + <PINMUX_GPIO79__FUNC_GPIO79>, + <PINMUX_GPIO80__FUNC_GPIO80>; + }; + pins-cc { + pinmux = <PINMUX_GPIO85__FUNC_GPIO85>, + <PINMUX_GPIO88__FUNC_GPIO88>, + <PINMUX_GPIO87__FUNC_GPIO87>, + <PINMUX_GPIO86__FUNC_GPIO86>; + }; + pins-rxd { + pinmux = <PINMUX_GPIO81__FUNC_GPIO81>, + <PINMUX_GPIO82__FUNC_GPIO82>, + <PINMUX_GPIO83__FUNC_GPIO83>, + <PINMUX_GPIO84__FUNC_GPIO84>; + }; + pins-mdio { + pinmux = <PINMUX_GPIO89__FUNC_GPIO89>, + <PINMUX_GPIO90__FUNC_GPIO90>; + input-disable; + bias-disable; + }; + pins-power { + pinmux = <PINMUX_GPIO91__FUNC_GPIO91>, + <PINMUX_GPIO92__FUNC_GPIO92>; + input-disable; + bias-disable; + }; + }; + gpio_keys_pins: gpio-keys-pins { pins { pinmux = <PINMUX_GPIO106__FUNC_GPIO106>; @@ -434,6 +500,28 @@ &xhci0 { status = "okay"; }; +ð { + phy-mode ="rgmii-rxid"; + phy-handle = <ðernet_phy0>; + snps,reset-gpio = <&pio 93 GPIO_ACTIVE_HIGH>; + snps,reset-delays-us = <0 10000 10000>; + mediatek,tx-delay-ps = <2030>; + pinctrl-names = "default", "sleep"; + pinctrl-0 = <ð_default_pins>; + pinctrl-1 = <ð_sleep_pins>; + status = "okay"; + + mdio { + compatible = "snps,dwmac-mdio"; + #address-cells = <1>; + #size-cells = <0>; + ethernet_phy0: ethernet-phy@1 { + compatible = "ethernet-phy-id001c.c916"; + reg = <0x1>; + }; + }; +}; + &xhci1 { vusb33-supply = <&mt6359_vusb_ldo_reg>; status = "okay"; diff --git a/arch/arm64/boot/dts/mediatek/mt8195.dtsi b/arch/arm64/boot/dts/mediatek/mt8195.dtsi index 5d31536f4c48..02112bbf2bdf 100644 --- a/arch/arm64/boot/dts/mediatek/mt8195.dtsi +++ b/arch/arm64/boot/dts/mediatek/mt8195.dtsi @@ -1046,6 +1046,92 @@ spis1: spi@1101e000 { status = "disabled"; }; + eth: ethernet@11021000 { + compatible = "mediatek,mt8195-gmac", "snps,dwmac-5.10a"; + reg = <0 0x11021000 0 0x4000>; + interrupts = <GIC_SPI 716 IRQ_TYPE_LEVEL_HIGH 0>; + interrupt-names = "macirq"; + clock-names = "axi", + "apb", + "mac_cg", + "mac_main", + "ptp_ref", + "rmii_internal"; + clocks = <&pericfg_ao CLK_PERI_AO_ETHERNET>, + <&pericfg_ao CLK_PERI_AO_ETHERNET_BUS>, + <&pericfg_ao CLK_PERI_AO_ETHERNET_MAC>, + <&topckgen CLK_TOP_SNPS_ETH_250M>, + <&topckgen CLK_TOP_SNPS_ETH_62P4M_PTP>, + <&topckgen CLK_TOP_SNPS_ETH_50M_RMII>; + assigned-clocks = <&topckgen CLK_TOP_SNPS_ETH_250M>, + <&topckgen CLK_TOP_SNPS_ETH_62P4M_PTP>, + <&topckgen CLK_TOP_SNPS_ETH_50M_RMII>; + assigned-clock-parents = <&topckgen CLK_TOP_ETHPLL_D2>, + <&topckgen CLK_TOP_ETHPLL_D8>, + <&topckgen CLK_TOP_ETHPLL_D10>; + power-domains = <&spm MT8195_POWER_DOMAIN_ETHER>; + mediatek,pericfg = <&infracfg_ao>; + snps,axi-config = <&stmmac_axi_setup>; + snps,mtl-rx-config = <&mtl_rx_setup>; + snps,mtl-tx-config = <&mtl_tx_setup>; + snps,txpbl = <16>; + snps,rxpbl = <16>; + snps,clk-csr = <0>; + status = "disabled"; + + stmmac_axi_setup: stmmac-axi-config { + snps,wr_osr_lmt = <0x7>; + snps,rd_osr_lmt = <0x7>; + snps,blen = <0 0 0 0 16 8 4>; + }; + + mtl_rx_setup: rx-queues-config { + snps,rx-queues-to-use = <4>; + snps,rx-sched-sp; + queue0 { + snps,dcb-algorithm; + snps,map-to-dma-channel = <0x0>; + }; + queue1 { + snps,dcb-algorithm; + snps,map-to-dma-channel = <0x0>; + }; + queue2 { + snps,dcb-algorithm; + snps,map-to-dma-channel = <0x0>; + }; + queue3 { + snps,dcb-algorithm; + snps,map-to-dma-channel = <0x0>; + }; + }; + + mtl_tx_setup: tx-queues-config { + snps,tx-queues-to-use = <4>; + snps,tx-sched-wrr; + queue0 { + snps,weight = <0x10>; + snps,dcb-algorithm; + snps,priority = <0x0>; + }; + queue1 { + snps,weight = <0x11>; + snps,dcb-algorithm; + snps,priority = <0x1>; + }; + queue2 { + snps,weight = <0x12>; + snps,dcb-algorithm; + snps,priority = <0x2>; + }; + queue3 { + snps,weight = <0x13>; + snps,dcb-algorithm; + snps,priority = <0x3>; + }; + }; + }; + xhci0: usb@11200000 { compatible = "mediatek,mt8195-xhci", "mediatek,mtk-xhci"; -- 2.25.1 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 12+ messages in thread
* Re: [RESEND PATCH v4] arm64: dts: mt8195: Add Ethernet controller 2022-12-21 2:25 ` Biao Huang @ 2022-12-21 10:13 ` AngeloGioacchino Del Regno -1 siblings, 0 replies; 12+ messages in thread From: AngeloGioacchino Del Regno @ 2022-12-21 10:13 UTC (permalink / raw) To: Biao Huang, Rob Herring, Krzysztof Kozlowski, Matthias Brugger Cc: devicetree, linux-arm-kernel, linux-mediatek, linux-kernel, macpaul.lin Il 21/12/22 03:25, Biao Huang ha scritto: > Add Ethernet controller node for mt8195. > > Signed-off-by: Biao Huang <biao.huang@mediatek.com> > --- > arch/arm64/boot/dts/mediatek/mt8195-demo.dts | 88 ++++++++++++++++++++ > arch/arm64/boot/dts/mediatek/mt8195.dtsi | 86 +++++++++++++++++++ > 2 files changed, 174 insertions(+) > ..snip.. > diff --git a/arch/arm64/boot/dts/mediatek/mt8195.dtsi b/arch/arm64/boot/dts/mediatek/mt8195.dtsi > index 5d31536f4c48..02112bbf2bdf 100644 > --- a/arch/arm64/boot/dts/mediatek/mt8195.dtsi > +++ b/arch/arm64/boot/dts/mediatek/mt8195.dtsi > @@ -1046,6 +1046,92 @@ spis1: spi@1101e000 { > status = "disabled"; > }; > > + eth: ethernet@11021000 { > + compatible = "mediatek,mt8195-gmac", "snps,dwmac-5.10a"; > + reg = <0 0x11021000 0 0x4000>; > + interrupts = <GIC_SPI 716 IRQ_TYPE_LEVEL_HIGH 0>; > + interrupt-names = "macirq"; > + clock-names = "axi", > + "apb", > + "mac_cg", mac_cg goes as last clock, as specified in the binding. Order: axi, apb, mac_main, ptp_ref, rmii_internal, mac_cg. Please fix. Regards, Angelo > + "mac_main", > + "ptp_ref", > + "rmii_internal"; > + clocks = <&pericfg_ao CLK_PERI_AO_ETHERNET>, > + <&pericfg_ao CLK_PERI_AO_ETHERNET_BUS>, > + <&pericfg_ao CLK_PERI_AO_ETHERNET_MAC>, > + <&topckgen CLK_TOP_SNPS_ETH_250M>, > + <&topckgen CLK_TOP_SNPS_ETH_62P4M_PTP>, > + <&topckgen CLK_TOP_SNPS_ETH_50M_RMII>; ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [RESEND PATCH v4] arm64: dts: mt8195: Add Ethernet controller @ 2022-12-21 10:13 ` AngeloGioacchino Del Regno 0 siblings, 0 replies; 12+ messages in thread From: AngeloGioacchino Del Regno @ 2022-12-21 10:13 UTC (permalink / raw) To: Biao Huang, Rob Herring, Krzysztof Kozlowski, Matthias Brugger Cc: devicetree, linux-arm-kernel, linux-mediatek, linux-kernel, macpaul.lin Il 21/12/22 03:25, Biao Huang ha scritto: > Add Ethernet controller node for mt8195. > > Signed-off-by: Biao Huang <biao.huang@mediatek.com> > --- > arch/arm64/boot/dts/mediatek/mt8195-demo.dts | 88 ++++++++++++++++++++ > arch/arm64/boot/dts/mediatek/mt8195.dtsi | 86 +++++++++++++++++++ > 2 files changed, 174 insertions(+) > ..snip.. > diff --git a/arch/arm64/boot/dts/mediatek/mt8195.dtsi b/arch/arm64/boot/dts/mediatek/mt8195.dtsi > index 5d31536f4c48..02112bbf2bdf 100644 > --- a/arch/arm64/boot/dts/mediatek/mt8195.dtsi > +++ b/arch/arm64/boot/dts/mediatek/mt8195.dtsi > @@ -1046,6 +1046,92 @@ spis1: spi@1101e000 { > status = "disabled"; > }; > > + eth: ethernet@11021000 { > + compatible = "mediatek,mt8195-gmac", "snps,dwmac-5.10a"; > + reg = <0 0x11021000 0 0x4000>; > + interrupts = <GIC_SPI 716 IRQ_TYPE_LEVEL_HIGH 0>; > + interrupt-names = "macirq"; > + clock-names = "axi", > + "apb", > + "mac_cg", mac_cg goes as last clock, as specified in the binding. Order: axi, apb, mac_main, ptp_ref, rmii_internal, mac_cg. Please fix. Regards, Angelo > + "mac_main", > + "ptp_ref", > + "rmii_internal"; > + clocks = <&pericfg_ao CLK_PERI_AO_ETHERNET>, > + <&pericfg_ao CLK_PERI_AO_ETHERNET_BUS>, > + <&pericfg_ao CLK_PERI_AO_ETHERNET_MAC>, > + <&topckgen CLK_TOP_SNPS_ETH_250M>, > + <&topckgen CLK_TOP_SNPS_ETH_62P4M_PTP>, > + <&topckgen CLK_TOP_SNPS_ETH_50M_RMII>; _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [RESEND PATCH v4] arm64: dts: mt8195: Add Ethernet controller 2022-12-21 10:13 ` AngeloGioacchino Del Regno @ 2022-12-22 1:43 ` Biao Huang (黄彪) -1 siblings, 0 replies; 12+ messages in thread From: Biao Huang (黄彪) @ 2022-12-22 1:43 UTC (permalink / raw) To: matthias.bgg@gmail.com, angelogioacchino.delregno@collabora.com, robh+dt@kernel.org, krzysztof.kozlowski+dt@linaro.org Cc: linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org, linux-mediatek@lists.infradead.org, Macpaul Lin (林智斌), devicetree@vger.kernel.org Dear Angelo, Thanks for your comments! On Wed, 2022-12-21 at 11:13 +0100, AngeloGioacchino Del Regno wrote: > Il 21/12/22 03:25, Biao Huang ha scritto: > > Add Ethernet controller node for mt8195. > > > > Signed-off-by: Biao Huang <biao.huang@mediatek.com> > > --- > > arch/arm64/boot/dts/mediatek/mt8195-demo.dts | 88 > > ++++++++++++++++++++ > > arch/arm64/boot/dts/mediatek/mt8195.dtsi | 86 > > +++++++++++++++++++ > > 2 files changed, 174 insertions(+) > > > > ..snip.. > > > diff --git a/arch/arm64/boot/dts/mediatek/mt8195.dtsi > > b/arch/arm64/boot/dts/mediatek/mt8195.dtsi > > index 5d31536f4c48..02112bbf2bdf 100644 > > --- a/arch/arm64/boot/dts/mediatek/mt8195.dtsi > > +++ b/arch/arm64/boot/dts/mediatek/mt8195.dtsi > > @@ -1046,6 +1046,92 @@ spis1: spi@1101e000 { > > status = "disabled"; > > }; > > > > + eth: ethernet@11021000 { > > + compatible = "mediatek,mt8195-gmac", > > "snps,dwmac-5.10a"; > > + reg = <0 0x11021000 0 0x4000>; > > + interrupts = <GIC_SPI 716 IRQ_TYPE_LEVEL_HIGH > > 0>; > > + interrupt-names = "macirq"; > > + clock-names = "axi", > > + "apb", > > + "mac_cg", > > mac_cg goes as last clock, as specified in the binding. > > Order: axi, apb, mac_main, ptp_ref, rmii_internal, mac_cg. > > Please fix. OK, will fix in next send. > > Regards, > Angelo > > > + "mac_main", > > + "ptp_ref", > > + "rmii_internal"; > > + clocks = <&pericfg_ao CLK_PERI_AO_ETHERNET>, > > + <&pericfg_ao > > CLK_PERI_AO_ETHERNET_BUS>, > > + <&pericfg_ao > > CLK_PERI_AO_ETHERNET_MAC>, > > + <&topckgen CLK_TOP_SNPS_ETH_250M>, > > + <&topckgen > > CLK_TOP_SNPS_ETH_62P4M_PTP>, > > + <&topckgen CLK_TOP_SNPS_ETH_50M_RMII>; > > ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [RESEND PATCH v4] arm64: dts: mt8195: Add Ethernet controller @ 2022-12-22 1:43 ` Biao Huang (黄彪) 0 siblings, 0 replies; 12+ messages in thread From: Biao Huang (黄彪) @ 2022-12-22 1:43 UTC (permalink / raw) To: matthias.bgg@gmail.com, angelogioacchino.delregno@collabora.com, robh+dt@kernel.org, krzysztof.kozlowski+dt@linaro.org Cc: linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org, linux-mediatek@lists.infradead.org, Macpaul Lin (林智斌), devicetree@vger.kernel.org Dear Angelo, Thanks for your comments! On Wed, 2022-12-21 at 11:13 +0100, AngeloGioacchino Del Regno wrote: > Il 21/12/22 03:25, Biao Huang ha scritto: > > Add Ethernet controller node for mt8195. > > > > Signed-off-by: Biao Huang <biao.huang@mediatek.com> > > --- > > arch/arm64/boot/dts/mediatek/mt8195-demo.dts | 88 > > ++++++++++++++++++++ > > arch/arm64/boot/dts/mediatek/mt8195.dtsi | 86 > > +++++++++++++++++++ > > 2 files changed, 174 insertions(+) > > > > ..snip.. > > > diff --git a/arch/arm64/boot/dts/mediatek/mt8195.dtsi > > b/arch/arm64/boot/dts/mediatek/mt8195.dtsi > > index 5d31536f4c48..02112bbf2bdf 100644 > > --- a/arch/arm64/boot/dts/mediatek/mt8195.dtsi > > +++ b/arch/arm64/boot/dts/mediatek/mt8195.dtsi > > @@ -1046,6 +1046,92 @@ spis1: spi@1101e000 { > > status = "disabled"; > > }; > > > > + eth: ethernet@11021000 { > > + compatible = "mediatek,mt8195-gmac", > > "snps,dwmac-5.10a"; > > + reg = <0 0x11021000 0 0x4000>; > > + interrupts = <GIC_SPI 716 IRQ_TYPE_LEVEL_HIGH > > 0>; > > + interrupt-names = "macirq"; > > + clock-names = "axi", > > + "apb", > > + "mac_cg", > > mac_cg goes as last clock, as specified in the binding. > > Order: axi, apb, mac_main, ptp_ref, rmii_internal, mac_cg. > > Please fix. OK, will fix in next send. > > Regards, > Angelo > > > + "mac_main", > > + "ptp_ref", > > + "rmii_internal"; > > + clocks = <&pericfg_ao CLK_PERI_AO_ETHERNET>, > > + <&pericfg_ao > > CLK_PERI_AO_ETHERNET_BUS>, > > + <&pericfg_ao > > CLK_PERI_AO_ETHERNET_MAC>, > > + <&topckgen CLK_TOP_SNPS_ETH_250M>, > > + <&topckgen > > CLK_TOP_SNPS_ETH_62P4M_PTP>, > > + <&topckgen CLK_TOP_SNPS_ETH_50M_RMII>; > > _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [RESEND PATCH v4] arm64: dts: mt8195: Add Ethernet controller 2022-12-21 2:25 ` Biao Huang @ 2022-12-21 13:16 ` Andrew Lunn -1 siblings, 0 replies; 12+ messages in thread From: Andrew Lunn @ 2022-12-21 13:16 UTC (permalink / raw) To: Biao Huang Cc: AngeloGioacchino Del Regno, Rob Herring, Krzysztof Kozlowski, Matthias Brugger, devicetree, linux-arm-kernel, linux-mediatek, linux-kernel, macpaul.lin > +ð { > + phy-mode ="rgmii-rxid"; That is pretty unusual. You don't see rxid, or txid very often, it is normally rgmii, or rgmii-id. > + phy-handle = <ðernet_phy0>; > + snps,reset-gpio = <&pio 93 GPIO_ACTIVE_HIGH>; > + snps,reset-delays-us = <0 10000 10000>; > + mediatek,tx-delay-ps = <2030>; How important is the 30 here? You appear to have the PHY doing the RX delay, and the MAC doing the TX delay. Normally we have the PHY do both. Can you actually do phy-mode = "rgmii-id", and mediatek,tx-delay-ps = <30> ? That would then have the PHY doing the basic 2ns delay, and the MAC doing the fine tuning needed for TX? Andrew ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [RESEND PATCH v4] arm64: dts: mt8195: Add Ethernet controller @ 2022-12-21 13:16 ` Andrew Lunn 0 siblings, 0 replies; 12+ messages in thread From: Andrew Lunn @ 2022-12-21 13:16 UTC (permalink / raw) To: Biao Huang Cc: AngeloGioacchino Del Regno, Rob Herring, Krzysztof Kozlowski, Matthias Brugger, devicetree, linux-arm-kernel, linux-mediatek, linux-kernel, macpaul.lin > +ð { > + phy-mode ="rgmii-rxid"; That is pretty unusual. You don't see rxid, or txid very often, it is normally rgmii, or rgmii-id. > + phy-handle = <ðernet_phy0>; > + snps,reset-gpio = <&pio 93 GPIO_ACTIVE_HIGH>; > + snps,reset-delays-us = <0 10000 10000>; > + mediatek,tx-delay-ps = <2030>; How important is the 30 here? You appear to have the PHY doing the RX delay, and the MAC doing the TX delay. Normally we have the PHY do both. Can you actually do phy-mode = "rgmii-id", and mediatek,tx-delay-ps = <30> ? That would then have the PHY doing the basic 2ns delay, and the MAC doing the fine tuning needed for TX? Andrew _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [RESEND PATCH v4] arm64: dts: mt8195: Add Ethernet controller 2022-12-21 13:16 ` Andrew Lunn @ 2022-12-22 1:56 ` Biao Huang (黄彪) -1 siblings, 0 replies; 12+ messages in thread From: Biao Huang (黄彪) @ 2022-12-22 1:56 UTC (permalink / raw) To: andrew@lunn.ch Cc: linux-mediatek@lists.infradead.org, linux-kernel@vger.kernel.org, robh+dt@kernel.org, devicetree@vger.kernel.org, Macpaul Lin (林智斌), linux-arm-kernel@lists.infradead.org, krzysztof.kozlowski+dt@linaro.org, matthias.bgg@gmail.com, angelogioacchino.delregno@collabora.com Dear Andrew, Thanks for your comments~ On Wed, 2022-12-21 at 14:16 +0100, Andrew Lunn wrote: > > +ð { > > + phy-mode ="rgmii-rxid"; > > That is pretty unusual. You don't see rxid, or txid very often, it is > normally rgmii, or rgmii-id. We didn't notice that, and in our design, we can ensure 2ns delay in tx direction, so we pick rgmii-rxid. Theoretically, we should support all the cases, and we'll set phy-mode to "rgmii-id" in next send. > > > + phy-handle = <ðernet_phy0>; > > + snps,reset-gpio = <&pio 93 GPIO_ACTIVE_HIGH>; > > + snps,reset-delays-us = <0 10000 10000>; > > + mediatek,tx-delay-ps = <2030>; > > How important is the 30 here? As documented in yaml, "For MT8188/MT8195 RGMII/RMII/MII interface, Allowed value need to be a multiple of 290, or will round down. Range 0~31*290. " so the 2030 is chosen here. > > You appear to have the PHY doing the RX delay, and the MAC doing the > TX delay. Normally we have the PHY do both. Can you actually do > > phy-mode = "rgmii-id", and mediatek,tx-delay-ps = <30> ? That would > then have the PHY doing the basic 2ns delay, and the MAC doing the > fine tuning needed for TX? Yes, we can do phy-mode = "rgmii-id". DTS and driver modification will send together in next send. Thanks for your valuable comments~ > > Andrew ^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [RESEND PATCH v4] arm64: dts: mt8195: Add Ethernet controller @ 2022-12-22 1:56 ` Biao Huang (黄彪) 0 siblings, 0 replies; 12+ messages in thread From: Biao Huang (黄彪) @ 2022-12-22 1:56 UTC (permalink / raw) To: andrew@lunn.ch Cc: linux-mediatek@lists.infradead.org, linux-kernel@vger.kernel.org, robh+dt@kernel.org, devicetree@vger.kernel.org, Macpaul Lin (林智斌), linux-arm-kernel@lists.infradead.org, krzysztof.kozlowski+dt@linaro.org, matthias.bgg@gmail.com, angelogioacchino.delregno@collabora.com Dear Andrew, Thanks for your comments~ On Wed, 2022-12-21 at 14:16 +0100, Andrew Lunn wrote: > > +ð { > > + phy-mode ="rgmii-rxid"; > > That is pretty unusual. You don't see rxid, or txid very often, it is > normally rgmii, or rgmii-id. We didn't notice that, and in our design, we can ensure 2ns delay in tx direction, so we pick rgmii-rxid. Theoretically, we should support all the cases, and we'll set phy-mode to "rgmii-id" in next send. > > > + phy-handle = <ðernet_phy0>; > > + snps,reset-gpio = <&pio 93 GPIO_ACTIVE_HIGH>; > > + snps,reset-delays-us = <0 10000 10000>; > > + mediatek,tx-delay-ps = <2030>; > > How important is the 30 here? As documented in yaml, "For MT8188/MT8195 RGMII/RMII/MII interface, Allowed value need to be a multiple of 290, or will round down. Range 0~31*290. " so the 2030 is chosen here. > > You appear to have the PHY doing the RX delay, and the MAC doing the > TX delay. Normally we have the PHY do both. Can you actually do > > phy-mode = "rgmii-id", and mediatek,tx-delay-ps = <30> ? That would > then have the PHY doing the basic 2ns delay, and the MAC doing the > fine tuning needed for TX? Yes, we can do phy-mode = "rgmii-id". DTS and driver modification will send together in next send. Thanks for your valuable comments~ > > Andrew _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2022-12-22 2:18 UTC | newest] Thread overview: 12+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2022-12-21 2:25 [RESEND v4 PATCH 0/1] arm64: dts: mt8195: Add Ethernet controller Biao Huang 2022-12-21 2:25 ` Biao Huang 2022-12-21 2:25 ` [RESEND PATCH v4] " Biao Huang 2022-12-21 2:25 ` Biao Huang 2022-12-21 10:13 ` AngeloGioacchino Del Regno 2022-12-21 10:13 ` AngeloGioacchino Del Regno 2022-12-22 1:43 ` Biao Huang (黄彪) 2022-12-22 1:43 ` Biao Huang (黄彪) 2022-12-21 13:16 ` Andrew Lunn 2022-12-21 13:16 ` Andrew Lunn 2022-12-22 1:56 ` Biao Huang (黄彪) 2022-12-22 1:56 ` Biao Huang (黄彪)
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.