Re: [PATCH V5 2/6] drivers/input/joystick: sensehat: Raspberry Pi Sense HAT joystick driver

[Dmitry Torokhov <dmitry.torokhov@gmail.com>]

Hi Charles,

On Fri, Dec 10, 2021 at 05:10:29PM -0500, Charles Mirabile wrote:
> This patch implements support for the joystick.
> It supports left/right/up/down/enter and is
> attached via i2c and a gpio pin for irq.

This is not really a joystick, at least not in current incarnation, but
rather a set of keys. I'd also question whether the selected set is
right for the application, I'd look into BTN_DPAD_* maybe? 

Or, if you want it to be a joystick, map ABS_X/ABS_Y.

> 
> Signed-off-by: Charles Mirabile <cmirabil@redhat.com>
> Co-developed-by: Mwesigwa Guma <mguma@redhat.com>
> Signed-off-by: Mwesigwa Guma <mguma@redhat.com>
> Co-developed-by: Joel Savitz <jsavitz@redhat.com>
> Signed-off-by: Joel Savitz <jsavitz@redhat.com>
> ---
>  drivers/input/joystick/Kconfig             |   8 ++
>  drivers/input/joystick/Makefile            |   1 +
>  drivers/input/joystick/sensehat-joystick.c | 119 +++++++++++++++++++++
>  3 files changed, 128 insertions(+)
>  create mode 100644 drivers/input/joystick/sensehat-joystick.c
> 
> diff --git a/drivers/input/joystick/Kconfig b/drivers/input/joystick/Kconfig
> index 3b23078bc7b5..d5c5ffe13903 100644
> --- a/drivers/input/joystick/Kconfig
> +++ b/drivers/input/joystick/Kconfig
> @@ -399,4 +399,12 @@ config JOYSTICK_N64
>  	  Say Y here if you want enable support for the four
>  	  built-in controller ports on the Nintendo 64 console.
>  
> +config JOYSTICK_SENSEHAT
> +	tristate "Raspberry Pi Sense HAT joystick"
> +	depends on GPIOLIB && INPUT && I2C

I do not see I2C accessed directly in this driver, nor GPIO interface.
You also do not need to depend on INPUT explicitly here.

> +	select MFD_SENSEHAT_CORE
> +
> +	help
> +	  This is the joystick driver for the Raspberry Pi Sense HAT
> +
>  endif
> diff --git a/drivers/input/joystick/Makefile b/drivers/input/joystick/Makefile
> index 5174b8aba2dd..39c8b5c6e5ae 100644
> --- a/drivers/input/joystick/Makefile
> +++ b/drivers/input/joystick/Makefile
> @@ -28,6 +28,7 @@ obj-$(CONFIG_JOYSTICK_N64)		+= n64joy.o
>  obj-$(CONFIG_JOYSTICK_PSXPAD_SPI)	+= psxpad-spi.o
>  obj-$(CONFIG_JOYSTICK_PXRC)		+= pxrc.o
>  obj-$(CONFIG_JOYSTICK_QWIIC)		+= qwiic-joystick.o
> +obj-$(CONFIG_JOYSTICK_SENSEHAT)         += sensehat-joystick.o
>  obj-$(CONFIG_JOYSTICK_SIDEWINDER)	+= sidewinder.o
>  obj-$(CONFIG_JOYSTICK_SPACEBALL)	+= spaceball.o
>  obj-$(CONFIG_JOYSTICK_SPACEORB)		+= spaceorb.o
> diff --git a/drivers/input/joystick/sensehat-joystick.c b/drivers/input/joystick/sensehat-joystick.c
> new file mode 100644
> index 000000000000..1f6bb09b4d1f
> --- /dev/null
> +++ b/drivers/input/joystick/sensehat-joystick.c
> @@ -0,0 +1,119 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later
> +/*
> + * Raspberry Pi Sense HAT joystick driver
> + * http://raspberrypi.org
> + *
> + * Copyright (C) 2015 Raspberry Pi
> + * Copyright (C) 2021 Charles Mirabile, Mwesigwa Guma, Joel Savitz
> + *
> + * Original Author: Serge Schneider
> + * Revised for upstream Linux by: Charles Mirabile, Mwesigwa Guma, Joel Savitz
> + */
> +
> +#include <linux/module.h>
> +#include <linux/input.h>
> +#include <linux/i2c.h>

Don't think you need this.

> +#include <linux/interrupt.h>
> +#include <linux/gpio/consumer.h>

Not needed.

> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +#include <linux/mfd/sensehat.h>
> +
> +#define SENSEHAT_KEYS 0xF2
> +
> +static int sensehat_get_joystick_state(struct sensehat *sensehat);
> +
> +static unsigned char keymap[] = {
> +	KEY_DOWN, KEY_RIGHT, KEY_UP, KEY_ENTER, KEY_LEFT,
> +};

Because you allowing manipulating keymap from userspace you need to make
a copy of it when setting up input device so that changes do would not
persist across bind/unbind.

This array needs to be marked const.

> +
> +static irqreturn_t sensehat_joystick_report(int n, void *cookie)
> +{
> +	int i;
> +	static s32 prev_keys;
> +	struct sensehat *sensehat = cookie;
> +	struct sensehat_joystick *sensehat_joystick = &sensehat->joystick;
> +	s32 keys = sensehat_get_joystick_state(sensehat);
> +	s32 changes = keys ^ prev_keys;
> +
> +	prev_keys = keys;
> +	for (i = 0; i < ARRAY_SIZE(keymap); ++i) {
> +		if (changes & (1 << i)) {
> +			input_report_key(sensehat_joystick->keys_dev, keymap[i],
> +					 keys & (1 << i));
> +		}
> +	}

If you go with keys/buttons approach, then use
bitmap_xor()/for_each_set_bit() - see
drivers/input/keyboard/cypress-sf.c::cypress_sf_irq_handler() for
example of use.

> +	input_sync(sensehat_joystick->keys_dev);
> +	return IRQ_HANDLED;
> +}
> +
> +static int sensehat_joystick_probe(struct platform_device *pdev)
> +{
> +	int ret;

Please call it "error";

> +	int i;
> +	struct sensehat *sensehat = dev_get_drvdata(&pdev->dev);
> +	struct sensehat_joystick *sensehat_joystick = &sensehat->joystick;

This structure (struct sensehat_joystick) should probably be private to
this driver.

> +
> +	sensehat_joystick->keys_dev = devm_input_allocate_device(&pdev->dev);
> +	if (!sensehat_joystick->keys_dev) {
> +		dev_err(&pdev->dev, "Could not allocate input device.\n");
> +		return -ENOMEM;
> +	}
> +
> +	for (i = 0; i < ARRAY_SIZE(keymap); i++) {
> +		set_bit(keymap[i], sensehat_joystick->keys_dev->keybit);
> +	}
> +
> +	sensehat_joystick->keys_dev->name = "Raspberry Pi Sense HAT Joystick";
> +	sensehat_joystick->keys_dev->phys = "rpi-sense-joy/input0";
> +	sensehat_joystick->keys_dev->id.bustype = BUS_I2C;
> +	sensehat_joystick->keys_dev->evbit[0] =
> +		BIT_MASK(EV_KEY) | BIT_MASK(EV_REP);
> +	sensehat_joystick->keys_dev->keycode = keymap;
> +	sensehat_joystick->keys_dev->keycodesize = sizeof(unsigned char);
> +	sensehat_joystick->keys_dev->keycodemax = ARRAY_SIZE(keymap);
> +
> +	ret = input_register_device(sensehat_joystick->keys_dev);
> +	if (ret) {
> +		dev_err(&pdev->dev, "Could not register input device.\n");
> +		return ret;
> +	}
> +
> +	ret = devm_request_threaded_irq(&pdev->dev, sensehat->i2c_client->irq,
> +					NULL, sensehat_joystick_report,
> +					IRQF_TRIGGER_RISING | IRQF_ONESHOT,

Do not specify trigger type, whoever set up client's interrupt should
have set up appropriate trigger.

> +					"keys", sensehat);
> +
> +	if (ret) {
> +		dev_err(&pdev->dev, "IRQ request failed.\n");
> +		return ret;
> +	}
> +	return 0;
> +}
> +
> +int sensehat_get_joystick_state(struct sensehat *sensehat)
> +{
> +	unsigned int reg;
> +	int ret = regmap_read(sensehat->regmap, SENSEHAT_KEYS, &reg);
> +
> +	return ret < 0 ? ret : reg;

I do not see the point in having this wrapper.

> +}
> +
> +static struct platform_device_id sensehat_joystick_device_id[] = {
> +	{ .name = "sensehat-joystick" },
> +	{},
> +};
> +MODULE_DEVICE_TABLE(platform, sensehat_joystick_device_id);
> +
> +static struct platform_driver sensehat_joystick_driver = {
> +	.probe = sensehat_joystick_probe,
> +	.driver = {
> +		.name = "sensehat-joystick",
> +	},
> +};
> +
> +module_platform_driver(sensehat_joystick_driver);
> +
> +MODULE_DESCRIPTION("Raspberry Pi Sense HAT joystick driver");
> +MODULE_AUTHOR("Serge Schneider <serge@raspberrypi.org>");
> +MODULE_LICENSE("GPL");
> -- 
> 2.31.1
> 

Thanks.

-- 
Dmitry