[RESEND PATCH 0/3] input: touchscreen: am335x: fix and improvements

[RESEND PATCH 0/3] input: touchscreen: am335x: fix and improvements

[Dario Binacchi]

This series grew out of a touchscreen validation activity on a custom
board. Oscilloscope measurements and driver source analysis led to these
patches.


Dario Binacchi (3):
  input: ti_am335x_tsc: set ADCREFM for X configuration
  input: ti_am335x_tsc: fix STEPCONFIG setup for Z2
  input: ti_am335x_tsc: lower the X and Y sampling time

 drivers/input/touchscreen/ti_am335x_tsc.c | 18 +++++++++++++-----
 1 file changed, 13 insertions(+), 5 deletions(-)

-- 
2.17.1

[RESEND PATCH 1/3] input: ti_am335x_tsc: set ADCREFM for X configuration

[Dario Binacchi]

As reported by the STEPCONFIG[1-16] registered field descriptions of the
TI reference manual, for the ADC "in single ended, SEL_INM_SWC_3_0 must
be 1xxx".

Unlike the Y and Z coordinates, this bit has not been set for the step
configuration registers used to sample the X coordinate.

Fixes: 1b8be32e691 ("Input: add support for TI Touchscreen controller")
Signed-off-by: Dario Binacchi <dariobin@libero.it>
---

 drivers/input/touchscreen/ti_am335x_tsc.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/input/touchscreen/ti_am335x_tsc.c b/drivers/input/touchscreen/ti_am335x_tsc.c
index 83e685557a19..fd3ffdd23470 100644
--- a/drivers/input/touchscreen/ti_am335x_tsc.c
+++ b/drivers/input/touchscreen/ti_am335x_tsc.c
@@ -131,7 +131,8 @@ static void titsc_step_config(struct titsc *ts_dev)
 	u32 stepenable;
 
 	config = STEPCONFIG_MODE_HWSYNC |
-			STEPCONFIG_AVG_16 | ts_dev->bit_xp;
+			STEPCONFIG_AVG_16 | ts_dev->bit_xp |
+			STEPCONFIG_INM_ADCREFM;
 	switch (ts_dev->wires) {
 	case 4:
 		config |= STEPCONFIG_INP(ts_dev->inp_yp) | ts_dev->bit_xn;
-- 
2.17.1

[RESEND PATCH 2/3] input: ti_am335x_tsc: fix STEPCONFIG setup for Z2

[Dario Binacchi]

The Z2 step configuration doesn't erase the SEL_INP_SWC_3_0 bit-field
before setting the ADC channel. This way its value could be corrupted by
the ADC channel selected for the Z1 coordinate.

Fixes: 8c896308fea ("input: ti_am335x_adc: use only FIFO0 and clean up a little")
Signed-off-by: Dario Binacchi <dariobin@libero.it>
---

 drivers/input/touchscreen/ti_am335x_tsc.c | 5 ++++-
 1 file changed, 4 insertions(+), 1 deletion(-)

diff --git a/drivers/input/touchscreen/ti_am335x_tsc.c b/drivers/input/touchscreen/ti_am335x_tsc.c
index fd3ffdd23470..cfc943423241 100644
--- a/drivers/input/touchscreen/ti_am335x_tsc.c
+++ b/drivers/input/touchscreen/ti_am335x_tsc.c
@@ -196,7 +196,10 @@ static void titsc_step_config(struct titsc *ts_dev)
 			STEPCONFIG_OPENDLY);
 
 	end_step++;
-	config |= STEPCONFIG_INP(ts_dev->inp_yn);
+	config = STEPCONFIG_MODE_HWSYNC |
+			STEPCONFIG_AVG_16 | ts_dev->bit_yp |
+			ts_dev->bit_xn | STEPCONFIG_INM_ADCREFM |
+			STEPCONFIG_INP(ts_dev->inp_yn);
 	titsc_writel(ts_dev, REG_STEPCONFIG(end_step), config);
 	titsc_writel(ts_dev, REG_STEPDELAY(end_step),
 			STEPCONFIG_OPENDLY);
-- 
2.17.1

[RESEND PATCH 3/3] input: ti_am335x_tsc: lower the X and Y sampling time

[Dario Binacchi]

The open delay time has to be applied only on the first sample of the
X/Y coordinates because on the following samples the ADC channel is not
changed. Removing this time from the samples after the first one,
"ti,coordinate-readouts" greater than 1, decreases the total acquisition
time, allowing to increase the number of acquired coordinates in the time
unit.

Signed-off-by: Dario Binacchi <dariobin@libero.it>

---

 drivers/input/touchscreen/ti_am335x_tsc.c | 10 +++++++---
 1 file changed, 7 insertions(+), 3 deletions(-)

diff --git a/drivers/input/touchscreen/ti_am335x_tsc.c b/drivers/input/touchscreen/ti_am335x_tsc.c
index cfc943423241..f4ef218bc1b8 100644
--- a/drivers/input/touchscreen/ti_am335x_tsc.c
+++ b/drivers/input/touchscreen/ti_am335x_tsc.c
@@ -126,7 +126,7 @@ static int titsc_config_wires(struct titsc *ts_dev)
 static void titsc_step_config(struct titsc *ts_dev)
 {
 	unsigned int	config;
-	int i;
+	int i, n;
 	int end_step, first_step, tsc_steps;
 	u32 stepenable;
 
@@ -151,9 +151,11 @@ static void titsc_step_config(struct titsc *ts_dev)
 	first_step = TOTAL_STEPS - tsc_steps;
 	/* Steps 16 to 16-coordinate_readouts is for X */
 	end_step = first_step + tsc_steps;
+	n = 0;
 	for (i = end_step - ts_dev->coordinate_readouts; i < end_step; i++) {
 		titsc_writel(ts_dev, REG_STEPCONFIG(i), config);
-		titsc_writel(ts_dev, REG_STEPDELAY(i), STEPCONFIG_OPENDLY);
+		titsc_writel(ts_dev, REG_STEPDELAY(i),
+			     n++ == 0 ? STEPCONFIG_OPENDLY : 0);
 	}
 
 	config = 0;
@@ -175,9 +177,11 @@ static void titsc_step_config(struct titsc *ts_dev)
 
 	/* 1 ... coordinate_readouts is for Y */
 	end_step = first_step + ts_dev->coordinate_readouts;
+	n = 0;
 	for (i = first_step; i < end_step; i++) {
 		titsc_writel(ts_dev, REG_STEPCONFIG(i), config);
-		titsc_writel(ts_dev, REG_STEPDELAY(i), STEPCONFIG_OPENDLY);
+		titsc_writel(ts_dev, REG_STEPDELAY(i),
+			     n++ == 0 ? STEPCONFIG_OPENDLY : 0);
 	}
 
 	/* Make CHARGECONFIG same as IDLECONFIG */
-- 
2.17.1

Re: [RESEND PATCH 0/3] input: touchscreen: am335x: fix and improvements

[Dmitry Torokhov]

On Sun, Dec 12, 2021 at 01:53:55PM +0100, Dario Binacchi wrote:
> 
> This series grew out of a touchscreen validation activity on a custom
> board. Oscilloscope measurements and driver source analysis led to these
> patches.
> 
> 
> Dario Binacchi (3):
>   input: ti_am335x_tsc: set ADCREFM for X configuration
>   input: ti_am335x_tsc: fix STEPCONFIG setup for Z2
>   input: ti_am335x_tsc: lower the X and Y sampling time
> 
>  drivers/input/touchscreen/ti_am335x_tsc.c | 18 +++++++++++++-----
>  1 file changed, 13 insertions(+), 5 deletions(-)

Applied the lot, thank you.

-- 
Dmitry