Re: [PATCH net-next v2 0/5] net: phylink: fix PCS without autoneg

["Russell King (Oracle)" <linux@armlinux.org.uk>]

On Tue, Jan 14, 2025 at 11:59:06AM +0100, Eric Woudstra wrote:
> On 1/13/25 10:21 AM, Russell King (Oracle) wrote:
> > Hi,
> > 
> > Eric Woudstra reported that a PCS attached using 2500base-X does not
> > see link when phylink is using in-band mode, but autoneg is disabled,
> > despite there being a valid 2500base-X signal being received. We have
> > these settings:
> > 
> > 	act_link_an_mode = MLO_AN_INBAND
> > 	pcs_neg_mode = PHYLINK_PCS_NEG_INBAND_DISABLED
> > 
> > Eric diagnosed it to phylink_decode_c37_word() setting state->link
> > false because the full-duplex bit isn't set in the non-existent link
> > partner advertisement word (which doesn't exist because in-band
> > autoneg is disabled!)
> > 
> > The test in phylink_mii_c22_pcs_decode_state() is supposed to catch
> > this state, but since we converted PCS to use neg_mode, testing the
> > Autoneg in the local advertisement is no longer sufficient - we need
> > to be looking at the neg_mode, which currently isn't provided.
> > 
> > We need to provide this via the .pcs_get_state() method, and this
> > will require modifying all PCS implementations to add the extra
> > argument to this method.
> > 
> > Patch 1 uses the PCS neg_mode in phylink_mac_pcs_get_state() to correct
> > the now obsolute usage of the Autoneg bit in the advertisement.
> > 
> > Patch 2 passes neg_mode into the .pcs_get_state() method, and updates
> > all users.
> > 
> > Patch 3 adds neg_mode as an argument to the various clause 22 state
> > decoder functions in phylink, modifying drivers to pass the neg_mode
> > through.
> > 
> > Patch 4 makes use of phylink_mii_c22_pcs_decode_state() rather than
> > using the Autoneg bit in the advertising field.
> > 
> > Patch 5 may be required for Eric's case - it ensures that we report
> > the correct state for interface types that we support only one set
> > of modes for when autoneg is disabled.
> > 
> > Changes in v2:
> > - Add test for NULL pcs in patch 1
> > 
> > I haven't added Eric's t-b because I used a different fix in patch 1.
> 
> So I tested this V2 patch and with the first link up command, I get the
> link up which is functional end to end.
> 
> Tested-by: Eric Woudstra <ericwouds@gmail.com>
> 
> PS, FYI: I do however still have the difference in phylink_mac_config().
> 
> At first the link is up with (before phy attached):
> phylink_mac_config: mode=inband/2500base-x
> 
> When the phy is attached, phylink_mac_config() is not called, but we
> have functional link.
> 
> When I do: ethtool -s eth1 advertise 0x28, then:
> phylink_mac_config: mode=inband/sgmii
> 
> And back again: ethtool -s eth1 advertise 0x800000000028, then:
> phylink_mac_config: mode=phy/2500base-x
> 
> I can share more log entries if needed.

I'm not worried - there's a sixth patch that I need to send once this
set of five are merged that will fix the above weirdness.

Thanks for testing.

-- 
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!