* [PATCH v2 1/2] dt-bindings: arm: Add compatible for SKOV i.MX8MP RevB board @ 2023-11-03 10:53 ` Oleksij Rempel 0 siblings, 0 replies; 16+ messages in thread From: Oleksij Rempel @ 2023-11-03 10:53 UTC (permalink / raw) To: Shawn Guo, Sascha Hauer, Rob Herring, Krzysztof Kozlowski, Søren Andersen, Sam Ravnborg Cc: Oleksij Rempel, kernel, linux-kernel, devicetree, linux-arm-kernel, NXP Linux Team, Fabio Estevam Add DT compatible string for a SKOV i.MX8MP RevB climate controller board. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> --- Documentation/devicetree/bindings/arm/fsl.yaml | 3 +++ 1 file changed, 3 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml index 9450b2c8a678..f457ad8e2ca1 100644 --- a/Documentation/devicetree/bindings/arm/fsl.yaml +++ b/Documentation/devicetree/bindings/arm/fsl.yaml @@ -1037,6 +1037,9 @@ properties: - gateworks,imx8mp-gw73xx-2x # i.MX8MP Gateworks Board - gateworks,imx8mp-gw74xx # i.MX8MP Gateworks Board - gateworks,imx8mp-gw7905-2x # i.MX8MP Gateworks Board + - skov,imx8mp-skov-revb-hdmi # SKOV i.MX8MP climate control without panel + - skov,imx8mp-skov-revb-lt6 # SKOV i.MX8MP climate control with 7” panel + - skov,imx8mp-skov-revb-mi1010ait-1cp1 # SKOV i.MX8MP climate control with 10.1" panel - toradex,verdin-imx8mp # Verdin iMX8M Plus Modules - toradex,verdin-imx8mp-nonwifi # Verdin iMX8M Plus Modules without Wi-Fi / BT - toradex,verdin-imx8mp-wifi # Verdin iMX8M Plus Wi-Fi / BT Modules -- 2.39.2 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH v2 1/2] dt-bindings: arm: Add compatible for SKOV i.MX8MP RevB board @ 2023-11-03 10:53 ` Oleksij Rempel 0 siblings, 0 replies; 16+ messages in thread From: Oleksij Rempel @ 2023-11-03 10:53 UTC (permalink / raw) To: Shawn Guo, Sascha Hauer, Rob Herring, Krzysztof Kozlowski, Søren Andersen, Sam Ravnborg Cc: Oleksij Rempel, kernel, linux-kernel, devicetree, linux-arm-kernel, NXP Linux Team, Fabio Estevam Add DT compatible string for a SKOV i.MX8MP RevB climate controller board. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> --- Documentation/devicetree/bindings/arm/fsl.yaml | 3 +++ 1 file changed, 3 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml index 9450b2c8a678..f457ad8e2ca1 100644 --- a/Documentation/devicetree/bindings/arm/fsl.yaml +++ b/Documentation/devicetree/bindings/arm/fsl.yaml @@ -1037,6 +1037,9 @@ properties: - gateworks,imx8mp-gw73xx-2x # i.MX8MP Gateworks Board - gateworks,imx8mp-gw74xx # i.MX8MP Gateworks Board - gateworks,imx8mp-gw7905-2x # i.MX8MP Gateworks Board + - skov,imx8mp-skov-revb-hdmi # SKOV i.MX8MP climate control without panel + - skov,imx8mp-skov-revb-lt6 # SKOV i.MX8MP climate control with 7” panel + - skov,imx8mp-skov-revb-mi1010ait-1cp1 # SKOV i.MX8MP climate control with 10.1" panel - toradex,verdin-imx8mp # Verdin iMX8M Plus Modules - toradex,verdin-imx8mp-nonwifi # Verdin iMX8M Plus Modules without Wi-Fi / BT - toradex,verdin-imx8mp-wifi # Verdin iMX8M Plus Wi-Fi / BT Modules -- 2.39.2 ^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH v2 2/2] arm64: dts: freescale: Add SKOV IMX8MP CPU revB board 2023-11-03 10:53 ` Oleksij Rempel @ 2023-11-03 10:53 ` Oleksij Rempel -1 siblings, 0 replies; 16+ messages in thread From: Oleksij Rempel @ 2023-11-03 10:53 UTC (permalink / raw) To: Shawn Guo, Sascha Hauer, Rob Herring, Krzysztof Kozlowski, Søren Andersen, Sam Ravnborg Cc: Oleksij Rempel, kernel, linux-kernel, devicetree, linux-arm-kernel, NXP Linux Team, Fabio Estevam Add Skov i.MX8MP based climate controller. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> --- arch/arm64/boot/dts/freescale/Makefile | 3 + .../boot/dts/freescale/imx8mp-skov-reva.dtsi | 713 ++++++++++++++++++ .../dts/freescale/imx8mp-skov-revb-hdmi.dts | 20 + .../dts/freescale/imx8mp-skov-revb-lt6.dts | 101 +++ .../imx8mp-skov-revb-mi1010ait-1cp1.dts | 100 +++ 5 files changed, 937 insertions(+) create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-skov-reva.dtsi create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-skov-revb-hdmi.dts create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-skov-revb-lt6.dts create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-skov-revb-mi1010ait-1cp1.dts diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile index 300049037eb0..45bfaf5a8b66 100644 --- a/arch/arm64/boot/dts/freescale/Makefile +++ b/arch/arm64/boot/dts/freescale/Makefile @@ -115,6 +115,9 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-icore-mx8mp-edimm2.2.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-msc-sm2s-ep1.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-rdk.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mp-skov-revb-hdmi.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mp-skov-revb-lt6.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mp-skov-revb-mi1010ait-1cp1.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-tqma8mpql-mba8mpxl.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-venice-gw71xx-2x.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-venice-gw72xx-2x.dtb diff --git a/arch/arm64/boot/dts/freescale/imx8mp-skov-reva.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-skov-reva.dtsi new file mode 100644 index 000000000000..1bfbd4a9bfae --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mp-skov-reva.dtsi @@ -0,0 +1,713 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) + +#include "imx8mp.dtsi" + +#include <dt-bindings/leds/common.h> + +/ { + aliases { + /* some of this aliases like backlight0, ethernetX and switch0 + * are needed for the bootloader. + */ + backlight0 = &backlight; + ethernet0 = &eqos; + ethernet1 = &lan1; + ethernet2 = &lan2; + rtc0 = &i2c_rtc; + rtc1 = &snvs_rtc; + switch0 = &switch; + }; + + /* + * Backlight is present only on some of boards, so it is disabled by + * default. + */ + backlight: backlight { + compatible = "pwm-backlight"; + pinctrl-0 = <&pinctrl_backlight>; + pwms = <&pwm1 0 20000 0>; + power-supply = <®_24v>; + enable-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>; + brightness-levels = <0 255>; + num-interpolated-steps = <17>; + default-brightness-level = <8>; + status = "disabled"; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_led>; + + led-0 { + label = "D1"; + color = <LED_COLOR_ID_GREEN>; + gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>; + function = LED_FUNCTION_STATUS; + default-state = "on"; + linux,default-trigger = "heartbeat"; + }; + + led-1 { + label = "D2"; + color = <LED_COLOR_ID_GREEN>; + gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-2 { + label = "D3"; + color = <LED_COLOR_ID_GREEN>; + gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + }; + + reg_1v2: regulator-1v2 { + compatible = "regulator-fixed"; + vin-supply = <®_5v_p>; + regulator-name = "1V2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + reg_2v5: regulator-2v5 { + compatible = "regulator-fixed"; + vin-supply = <®_5v_s>; + regulator-name = "2V5"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + }; + + reg_3v3: regulator-3v3 { + compatible = "regulator-fixed"; + vin-supply = <®_5v_s>; + regulator-name = "3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + /* + * This regulator will provide power as long as possible even if + * undervoltage is detected. + */ + reg_5v_p: regulator-5v-p { + compatible = "regulator-fixed"; + regulator-name = "5V_P"; + vin-supply = <®_24v>; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + /* + * This regulator will be automatically shutdown if undervoltage is + * detected. + */ + reg_5v_s: regulator-5v-s { + compatible = "regulator-fixed"; + regulator-name = "5V_S"; + vin-supply = <®_24v>; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + reg_24v: regulator-24v { + compatible = "regulator-fixed"; + regulator-name = "24V"; + regulator-min-microvolt = <24000000>; + regulator-max-microvolt = <24000000>; + }; + + reg_can2rs: regulator-can2rs { + compatible = "regulator-fixed"; + regulator-name = "CAN2RS"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_can2rs>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio4 22 GPIO_ACTIVE_LOW>; + }; + + reg_canrs: regulator-canrs { + compatible = "regulator-fixed"; + regulator-name = "CANRS"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_canrs>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio4 21 GPIO_ACTIVE_LOW>; + }; + + reg_tft_vcom: regulator-tft-vcom { + compatible = "pwm-regulator"; + pwms = <&pwm4 0 20000 0>; + regulator-name = "VCOM"; + vin-supply = <®_5v_s>; + regulator-min-microvolt = <3600000>; + regulator-max-microvolt = <3600000>; + regulator-always-on; + voltage-table = <3600000 26>; + status = "disabled"; + }; + + reg_vsd_3v3: regulator-vsd-3v3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_vsd_3v3>; + vin-supply = <®_vdd_3v3>; + compatible = "regulator-fixed"; + regulator-name = "VSD_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&A53_0 { + cpu-supply = <®_vdd_arm>; +}; + +&A53_1 { + cpu-supply = <®_vdd_arm>; +}; + +&A53_2 { + cpu-supply = <®_vdd_arm>; +}; + +&A53_3 { + cpu-supply = <®_vdd_arm>; +}; + +&ecspi2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi2>; + cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>; + status = "okay"; + + adc: adc@0 { + compatible = "microchip,mcp3002"; + reg = <0>; + vref-supply = <®_vdd_3v3>; + spi-max-frequency = <1000000>; + #io-channel-cells = <1>; + }; +}; + +&eqos { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_eqos>; + phy-mode = "rgmii"; + status = "okay"; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&flexcan1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan1>; + xceiver-supply = <®_canrs>; + status = "okay"; +}; + +&flexcan2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan2>; + xceiver-supply = <®_can2rs>; + status = "okay"; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + pmic@25 { + compatible = "nxp,pca9450c"; + reg = <0x25>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pmic>; + interrupts-extended = <&gpio1 3 IRQ_TYPE_EDGE_RISING>; + sd-vsel-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>; + + regulators { + reg_vdd_soc: BUCK1 { + regulator-name = "VDD_SOC"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <2187500>; + vin-supply = <®_5v_p>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <3125>; + }; + + reg_vdd_arm: BUCK2 { + regulator-name = "VDD_ARM"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <2187500>; + vin-supply = <®_5v_p>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <3125>; + nxp,dvs-run-voltage = <950000>; + nxp,dvs-standby-voltage = <850000>; + }; + + reg_vdd_3v3: BUCK4 { + regulator-name = "VDD_3V3"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <3400000>; + vin-supply = <®_5v_p>; + regulator-boot-on; + regulator-always-on; + }; + + reg_vdd_1v8: BUCK5 { + regulator-name = "VDD_1V8"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <3400000>; + vin-supply = <®_5v_p>; + regulator-boot-on; + regulator-always-on; + }; + + reg_nvcc_dram_1v1: BUCK6 { + regulator-name = "NVCC_DRAM_1V1"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <3400000>; + vin-supply = <®_5v_p>; + regulator-boot-on; + regulator-always-on; + }; + + reg_nvcc_snvs_1v8: LDO1 { + regulator-name = "NVCC_SNVS_1V8"; + regulator-min-microvolt = <1600000>; + regulator-max-microvolt = <3300000>; + vin-supply = <®_5v_p>; + regulator-boot-on; + regulator-always-on; + }; + + reg_vdda_1v8: LDO3 { + regulator-name = "VDDA_1V8"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + vin-supply = <®_5v_p>; + regulator-boot-on; + regulator-always-on; + }; + + reg_nvcc_sd2: LDO5 { + regulator-name = "NVCC_SD2"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + vin-supply = <®_5v_p>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; +}; + +&i2c3 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + i2c_rtc: rtc@51 { + compatible = "nxp,pcf85063tp"; + reg = <0x51>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rtc>; + interrupts-extended = <&gpio4 31 IRQ_TYPE_EDGE_FALLING>; + quartz-load-femtofarads = <12500>; + }; +}; + +&i2c4 { + clock-frequency = <380000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c4>; + status = "okay"; + + switch: switch@5f { + compatible = "microchip,ksz9893"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_switch>; + reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>; + reg = <0x5f>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + lan1: port@0 { + reg = <0>; + phy-mode = "internal"; + label = "lan1"; + }; + + lan2: port@1 { + reg = <1>; + phy-mode = "internal"; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "cpu"; + ethernet = <&eqos>; + /* 2ns rgmii-rxid is implemented on PCB. + * Switch should add only rgmii-txid. + */ + phy-mode = "rgmii-txid"; + tx-internal-delay-ps = <2000>; + rx-internal-delay-ps = <0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; +}; + +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm1>; +}; + +&pwm4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm4>; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + /* console */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&usb3_0 { + status = "okay"; +}; + +&usb3_1 { + status = "okay"; +}; + +&usb3_phy0 { + vbus-supply = <®_3v3>; + status = "okay"; +}; + +&usb3_phy1 { + vbus-supply = <®_3v3>; + status = "okay"; +}; + +&usb_dwc3_0 { + dr_mode = "host"; +}; + +&usb_dwc3_1 { + dr_mode = "host"; +}; + +/* SD Card */ +&usdhc2 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; + vmmc-supply = <®_vsd_3v3>; + vqmmc-supply = <®_nvcc_sd2>; + cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; + wp-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>; + bus-width = <4>; + status = "okay"; +}; + +/* eMMC */ +&usdhc3 { + assigned-clocks = <&clk IMX8MP_CLK_USDHC3>; + assigned-clock-rates = <400000000>; + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc3>; + pinctrl-1 = <&pinctrl_usdhc3_100mhz>; + pinctrl-2 = <&pinctrl_usdhc3_200mhz>; + vmmc-supply = <®_vdd_3v3>; + vqmmc-supply = <®_vdd_1v8>; + bus-width = <8>; + no-sd; + no-sdio; + non-removable; + status = "okay"; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; + status = "okay"; +}; + +&iomuxc { + pinctrl_backlight: backlightgrp { + fsl,pins = < + MX8MP_IOMUXC_SAI2_TXFS__GPIO4_IO24 0x0100 + >; + }; + + pinctrl_can2rs: can2rsgrp { + fsl,pins = < + MX8MP_IOMUXC_SAI2_RXC__GPIO4_IO22 0x154 + >; + }; + + pinctrl_canrs: canrsgrp { + fsl,pins = < + MX8MP_IOMUXC_SAI2_RXFS__GPIO4_IO21 0x154 + >; + }; + + pinctrl_ecspi2: ecspi2grp { + fsl,pins = < + MX8MP_IOMUXC_ECSPI2_SCLK__ECSPI2_SCLK 0x44 + MX8MP_IOMUXC_ECSPI2_MOSI__ECSPI2_MOSI 0x44 + MX8MP_IOMUXC_ECSPI2_MISO__ECSPI2_MISO 0x44 + MX8MP_IOMUXC_ECSPI2_SS0__GPIO5_IO13 0x40 + >; + }; + + pinctrl_eqos: eqosgrp { + fsl,pins = < + MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0 0x91 + MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1 0x91 + MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2 0x91 + MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3 0x91 + MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK 0x91 + MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL 0x91 + MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0 0x1f + MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1 0x1f + MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2 0x1f + MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3 0x1f + MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL 0x1f + MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK 0x1f + >; + }; + + pinctrl_flexcan1: flexcan1grp { + fsl,pins = < + MX8MP_IOMUXC_SPDIF_RX__CAN1_RX 0x154 + MX8MP_IOMUXC_SPDIF_TX__CAN1_TX 0x154 + >; + }; + + pinctrl_flexcan2: flexcan2grp { + fsl,pins = < + MX8MP_IOMUXC_SAI2_MCLK__CAN2_RX 0x154 + MX8MP_IOMUXC_SAI2_TXD0__CAN2_TX 0x154 + >; + }; + + pinctrl_gpio_led: gpioledgrp { + fsl,pins = < + MX8MP_IOMUXC_GPIO1_IO05__GPIO1_IO05 0x19 + MX8MP_IOMUXC_GPIO1_IO06__GPIO1_IO06 0x19 + MX8MP_IOMUXC_GPIO1_IO07__GPIO1_IO07 0x19 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL 0x400001c2 + MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA 0x400001c2 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX8MP_IOMUXC_I2C3_SCL__I2C3_SCL 0x400001c2 + MX8MP_IOMUXC_I2C3_SDA__I2C3_SDA 0x400001c2 + >; + }; + + pinctrl_i2c4: i2c4grp { + fsl,pins = < + MX8MP_IOMUXC_I2C4_SCL__I2C4_SCL 0x400001c3 + MX8MP_IOMUXC_I2C4_SDA__I2C4_SDA 0x400001c3 + >; + }; + + pinctrl_pmic: pmicirqgrp { + fsl,pins = < + MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03 0x41 + MX8MP_IOMUXC_GPIO1_IO04__GPIO1_IO04 0x41 + >; + }; + + pinctrl_pwm1: pwm1grp { + fsl,pins = < + MX8MP_IOMUXC_SPDIF_EXT_CLK__PWM1_OUT 0x116 + >; + }; + + pinctrl_pwm4: pwm4grp { + fsl,pins = < + MX8MP_IOMUXC_SAI3_MCLK__PWM4_OUT 0x116 + >; + }; + + pinctrl_reg_vsd_3v3: regvsd3v3grp { + fsl,pins = < + MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19 0x40 + >; + }; + + pinctrl_rtc: rtcgrp { + fsl,pins = < + MX8MP_IOMUXC_SAI3_TXFS__GPIO4_IO31 0x41 + >; + }; + + pinctrl_switch: switchgrp { + fsl,pins = < + MX8MP_IOMUXC_SAI3_TXC__GPIO5_IO00 0x41 + MX8MP_IOMUXC_SAI3_TXD__GPIO5_IO01 0x41 + >; + }; + + pinctrl_touchscreen: touchscreengrp { + fsl,pins = < + /* external 10 k pull up */ + /* CTP_INT */ + MX8MP_IOMUXC_SAI3_RXFS__GPIO4_IO28 0x41 + /* CTP_RST */ + MX8MP_IOMUXC_SAI3_RXC__GPIO4_IO29 0x41 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX8MP_IOMUXC_UART1_RXD__UART1_DCE_RX 0x140 + MX8MP_IOMUXC_UART1_TXD__UART1_DCE_TX 0x140 + MX8MP_IOMUXC_UART3_RXD__UART1_DTE_RTS 0x140 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX 0x14f + MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX 0x14f + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x190 + MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d0 + MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d0 + MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d0 + MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d0 + MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d0 + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp { + fsl,pins = < + MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x194 + MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d4 + MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d4 + MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d4 + MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d4 + MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d4 + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp { + fsl,pins = < + MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x196 + MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d6 + MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d6 + MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d6 + MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d6 + MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d6 + >; + }; + + pinctrl_usdhc2_gpio: usdhc2gpiogrp { + fsl,pins = < + MX8MP_IOMUXC_SD2_CD_B__GPIO2_IO12 0x1c4 + MX8MP_IOMUXC_SD2_WP__GPIO2_IO20 0x1c4 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x190 + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d0 + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d0 + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d0 + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d0 + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d0 + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d0 + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d0 + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d0 + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d0 + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x190 + >; + }; + + pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp { + fsl,pins = < + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x194 + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d4 + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d4 + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d4 + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d4 + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d4 + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d4 + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d4 + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d4 + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d4 + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x194 + >; + }; + + pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp { + fsl,pins = < + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x196 + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d6 + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d6 + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d6 + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d6 + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d6 + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d6 + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d6 + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d6 + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d6 + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x196 + >; + }; + + pinctrl_wdog: wdoggrp { + fsl,pins = < + MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B 0xc6 + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-skov-revb-hdmi.dts b/arch/arm64/boot/dts/freescale/imx8mp-skov-revb-hdmi.dts new file mode 100644 index 000000000000..c1ca69da3cb8 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mp-skov-revb-hdmi.dts @@ -0,0 +1,20 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) + +/dts-v1/; + +#include "imx8mp-skov-reva.dtsi" + +/ { + model = "SKOV IMX8MP CPU revB - HDMI"; + compatible = "skov,imx8mp-skov-revb-hdmi", "fsl,imx8mp"; +}; + +&iomuxc { + pinctrl_hdmi: hdmigrp { + fsl,pins = < + MX8MP_IOMUXC_HDMI_DDC_SCL__HDMIMIX_HDMI_SCL 0x1c3 + MX8MP_IOMUXC_HDMI_DDC_SDA__HDMIMIX_HDMI_SDA 0x1c3 + MX8MP_IOMUXC_HDMI_HPD__HDMIMIX_HDMI_HPD 0x19 + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-skov-revb-lt6.dts b/arch/arm64/boot/dts/freescale/imx8mp-skov-revb-lt6.dts new file mode 100644 index 000000000000..ccbd3abedd69 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mp-skov-revb-lt6.dts @@ -0,0 +1,101 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) + +/dts-v1/; + +#include "imx8mp-skov-reva.dtsi" + +/ { + model = "SKOV IMX8MP CPU revB - LT6"; + compatible = "skov,imx8mp-skov-revb-lt6", "fsl,imx8mp"; + + touchscreen { + compatible = "resistive-adc-touch"; + io-channels = <&adc_ts 1>, <&adc_ts 3>, <&adc_ts 4>, <&adc_ts 5>; + io-channel-names = "y", "z1", "z2", "x"; + touchscreen-min-pressure = <65000>; + touchscreen-inverted-y; + touchscreen-swapped-x-y; + touchscreen-x-plate-ohms = <300>; + }; +}; + +®_tft_vcom { + regulator-min-microvolt = <3600000>; + regulator-max-microvolt = <3600000>; + voltage-table = <3600000 26>; + status = "okay"; +}; + +&pwm4 { + status = "okay"; +}; + +&backlight { + status = "okay"; +}; + +&ecspi1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1>; + cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>; + status = "okay"; + + adc_ts: adc@0 { + compatible = "ti,tsc2046e-adc"; + reg = <0>; + pinctrl-0 = <&pinctrl_touch>; + pinctrl-names ="default"; + spi-max-frequency = <1000000>; + interrupts-extended = <&gpio4 25 IRQ_TYPE_LEVEL_LOW>; + #io-channel-cells = <1>; + + #address-cells = <1>; + #size-cells = <0>; + + channel@1 { + reg = <1>; + settling-time-us = <700>; + oversampling-ratio = <5>; + }; + + channel@3 { + reg = <3>; + settling-time-us = <700>; + oversampling-ratio = <5>; + }; + + channel@4 { + reg = <4>; + settling-time-us = <700>; + oversampling-ratio = <5>; + }; + + channel@5 { + reg = <5>; + settling-time-us = <700>; + oversampling-ratio = <5>; + }; + }; +}; + +&pwm1 { + status = "okay"; +}; + +&iomuxc { + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX8MP_IOMUXC_ECSPI1_SCLK__ECSPI1_SCLK 0x44 + MX8MP_IOMUXC_ECSPI1_MOSI__ECSPI1_MOSI 0x44 + MX8MP_IOMUXC_ECSPI1_MISO__ECSPI1_MISO 0x44 + MX8MP_IOMUXC_ECSPI1_SS0__GPIO5_IO09 0x40 + >; + }; + + pinctrl_touch: touchgrp { + fsl,pins = < + /* external pull up */ + MX8MP_IOMUXC_SAI2_TXC__GPIO4_IO25 0x40 + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-skov-revb-mi1010ait-1cp1.dts b/arch/arm64/boot/dts/freescale/imx8mp-skov-revb-mi1010ait-1cp1.dts new file mode 100644 index 000000000000..3c2efdc59bfa --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mp-skov-revb-mi1010ait-1cp1.dts @@ -0,0 +1,100 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) + +/dts-v1/; + +#include "imx8mp-skov-reva.dtsi" + +/ { + model = "SKOV IMX8MP CPU revB - MI1010AIT-1CP1"; + compatible = "skov,imx8mp-skov-revb-mi1010ait-1cp1", "fsl,imx8mp"; + + panel { + compatible = "multi-inno,mi1010ait-1cp"; + backlight = <&backlight>; + power-supply = <®_tft_vcom>; + + port { + in_lvds0: endpoint { + remote-endpoint = <&ldb_lvds_ch0>; + }; + }; + }; +}; + +&backlight { + status = "okay"; +}; + +&i2c2 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + touchscreen@38 { + compatible = "edt,edt-ft5406"; + reg = <0x38>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_touchscreen>; + interrupts-extended = <&gpio4 28 IRQ_TYPE_EDGE_FALLING>; + reset-gpios = <&gpio4 29 GPIO_ACTIVE_LOW>; + touchscreen-size-x = <1280>; + touchscreen-size-y = <800>; + vcc-supply = <®_vdd_3v3>; + iovcc-supply = <®_vdd_3v3>; + wakeup-source; + }; +}; + +&lcdif2 { + status = "okay"; +}; + +&lvds_bridge { + /* IMX8MP_CLK_MEDIA_LDB = IMX8MP_CLK_MEDIA_DISP2_PIX * 7 */ + assigned-clock-rates = <482300000>; + status = "okay"; + + ports { + port@1 { + ldb_lvds_ch0: endpoint { + remote-endpoint = <&in_lvds0>; + }; + }; + }; +}; + +&media_blk_ctrl { + /* currently it is not possible to let display clocks confugure + * automatically, so we need to set them manually + */ + assigned-clock-rates = <500000000>, <200000000>, <0>, + /* IMX8MP_CLK_MEDIA_DISP2_PIX = pixelclk of lvds panel */ + <68900000>, + /* IMX8MP_VIDEO_PLL1 = IMX8MP_CLK_MEDIA_LDB * 2 */ + <964600000>; +}; + +&pwm4 { + status = "okay"; +}; + +&pwm1 { + status = "okay"; +}; + +®_tft_vcom { + regulator-min-microvolt = <3160000>; + regulator-max-microvolt = <3160000>; + voltage-table = <3160000 73>; + status = "okay"; +}; + +&iomuxc { + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL 0x400001c2 + MX8MP_IOMUXC_I2C2_SDA__I2C2_SDA 0x400001c2 + >; + }; +}; -- 2.39.2 _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply related [flat|nested] 16+ messages in thread
* [PATCH v2 2/2] arm64: dts: freescale: Add SKOV IMX8MP CPU revB board @ 2023-11-03 10:53 ` Oleksij Rempel 0 siblings, 0 replies; 16+ messages in thread From: Oleksij Rempel @ 2023-11-03 10:53 UTC (permalink / raw) To: Shawn Guo, Sascha Hauer, Rob Herring, Krzysztof Kozlowski, Søren Andersen, Sam Ravnborg Cc: Oleksij Rempel, kernel, linux-kernel, devicetree, linux-arm-kernel, NXP Linux Team, Fabio Estevam Add Skov i.MX8MP based climate controller. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> --- arch/arm64/boot/dts/freescale/Makefile | 3 + .../boot/dts/freescale/imx8mp-skov-reva.dtsi | 713 ++++++++++++++++++ .../dts/freescale/imx8mp-skov-revb-hdmi.dts | 20 + .../dts/freescale/imx8mp-skov-revb-lt6.dts | 101 +++ .../imx8mp-skov-revb-mi1010ait-1cp1.dts | 100 +++ 5 files changed, 937 insertions(+) create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-skov-reva.dtsi create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-skov-revb-hdmi.dts create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-skov-revb-lt6.dts create mode 100644 arch/arm64/boot/dts/freescale/imx8mp-skov-revb-mi1010ait-1cp1.dts diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile index 300049037eb0..45bfaf5a8b66 100644 --- a/arch/arm64/boot/dts/freescale/Makefile +++ b/arch/arm64/boot/dts/freescale/Makefile @@ -115,6 +115,9 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mp-evk.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-icore-mx8mp-edimm2.2.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-msc-sm2s-ep1.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-rdk.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mp-skov-revb-hdmi.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mp-skov-revb-lt6.dtb +dtb-$(CONFIG_ARCH_MXC) += imx8mp-skov-revb-mi1010ait-1cp1.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-tqma8mpql-mba8mpxl.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-venice-gw71xx-2x.dtb dtb-$(CONFIG_ARCH_MXC) += imx8mp-venice-gw72xx-2x.dtb diff --git a/arch/arm64/boot/dts/freescale/imx8mp-skov-reva.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-skov-reva.dtsi new file mode 100644 index 000000000000..1bfbd4a9bfae --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mp-skov-reva.dtsi @@ -0,0 +1,713 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) + +#include "imx8mp.dtsi" + +#include <dt-bindings/leds/common.h> + +/ { + aliases { + /* some of this aliases like backlight0, ethernetX and switch0 + * are needed for the bootloader. + */ + backlight0 = &backlight; + ethernet0 = &eqos; + ethernet1 = &lan1; + ethernet2 = &lan2; + rtc0 = &i2c_rtc; + rtc1 = &snvs_rtc; + switch0 = &switch; + }; + + /* + * Backlight is present only on some of boards, so it is disabled by + * default. + */ + backlight: backlight { + compatible = "pwm-backlight"; + pinctrl-0 = <&pinctrl_backlight>; + pwms = <&pwm1 0 20000 0>; + power-supply = <®_24v>; + enable-gpios = <&gpio4 24 GPIO_ACTIVE_HIGH>; + brightness-levels = <0 255>; + num-interpolated-steps = <17>; + default-brightness-level = <8>; + status = "disabled"; + }; + + leds { + compatible = "gpio-leds"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_gpio_led>; + + led-0 { + label = "D1"; + color = <LED_COLOR_ID_GREEN>; + gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>; + function = LED_FUNCTION_STATUS; + default-state = "on"; + linux,default-trigger = "heartbeat"; + }; + + led-1 { + label = "D2"; + color = <LED_COLOR_ID_GREEN>; + gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>; + default-state = "off"; + }; + + led-2 { + label = "D3"; + color = <LED_COLOR_ID_GREEN>; + gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + }; + + reg_1v2: regulator-1v2 { + compatible = "regulator-fixed"; + vin-supply = <®_5v_p>; + regulator-name = "1V2"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + }; + + reg_2v5: regulator-2v5 { + compatible = "regulator-fixed"; + vin-supply = <®_5v_s>; + regulator-name = "2V5"; + regulator-min-microvolt = <2500000>; + regulator-max-microvolt = <2500000>; + }; + + reg_3v3: regulator-3v3 { + compatible = "regulator-fixed"; + vin-supply = <®_5v_s>; + regulator-name = "3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + + /* + * This regulator will provide power as long as possible even if + * undervoltage is detected. + */ + reg_5v_p: regulator-5v-p { + compatible = "regulator-fixed"; + regulator-name = "5V_P"; + vin-supply = <®_24v>; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + /* + * This regulator will be automatically shutdown if undervoltage is + * detected. + */ + reg_5v_s: regulator-5v-s { + compatible = "regulator-fixed"; + regulator-name = "5V_S"; + vin-supply = <®_24v>; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + + reg_24v: regulator-24v { + compatible = "regulator-fixed"; + regulator-name = "24V"; + regulator-min-microvolt = <24000000>; + regulator-max-microvolt = <24000000>; + }; + + reg_can2rs: regulator-can2rs { + compatible = "regulator-fixed"; + regulator-name = "CAN2RS"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_can2rs>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio4 22 GPIO_ACTIVE_LOW>; + }; + + reg_canrs: regulator-canrs { + compatible = "regulator-fixed"; + regulator-name = "CANRS"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_canrs>; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio4 21 GPIO_ACTIVE_LOW>; + }; + + reg_tft_vcom: regulator-tft-vcom { + compatible = "pwm-regulator"; + pwms = <&pwm4 0 20000 0>; + regulator-name = "VCOM"; + vin-supply = <®_5v_s>; + regulator-min-microvolt = <3600000>; + regulator-max-microvolt = <3600000>; + regulator-always-on; + voltage-table = <3600000 26>; + status = "disabled"; + }; + + reg_vsd_3v3: regulator-vsd-3v3 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_reg_vsd_3v3>; + vin-supply = <®_vdd_3v3>; + compatible = "regulator-fixed"; + regulator-name = "VSD_3V3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&gpio2 19 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&A53_0 { + cpu-supply = <®_vdd_arm>; +}; + +&A53_1 { + cpu-supply = <®_vdd_arm>; +}; + +&A53_2 { + cpu-supply = <®_vdd_arm>; +}; + +&A53_3 { + cpu-supply = <®_vdd_arm>; +}; + +&ecspi2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi2>; + cs-gpios = <&gpio5 13 GPIO_ACTIVE_LOW>; + status = "okay"; + + adc: adc@0 { + compatible = "microchip,mcp3002"; + reg = <0>; + vref-supply = <®_vdd_3v3>; + spi-max-frequency = <1000000>; + #io-channel-cells = <1>; + }; +}; + +&eqos { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_eqos>; + phy-mode = "rgmii"; + status = "okay"; + + fixed-link { + speed = <1000>; + full-duplex; + }; +}; + +&flexcan1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan1>; + xceiver-supply = <®_canrs>; + status = "okay"; +}; + +&flexcan2 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_flexcan2>; + xceiver-supply = <®_can2rs>; + status = "okay"; +}; + +&i2c1 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c1>; + status = "okay"; + + pmic@25 { + compatible = "nxp,pca9450c"; + reg = <0x25>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pmic>; + interrupts-extended = <&gpio1 3 IRQ_TYPE_EDGE_RISING>; + sd-vsel-gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>; + + regulators { + reg_vdd_soc: BUCK1 { + regulator-name = "VDD_SOC"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <2187500>; + vin-supply = <®_5v_p>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <3125>; + }; + + reg_vdd_arm: BUCK2 { + regulator-name = "VDD_ARM"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <2187500>; + vin-supply = <®_5v_p>; + regulator-boot-on; + regulator-always-on; + regulator-ramp-delay = <3125>; + nxp,dvs-run-voltage = <950000>; + nxp,dvs-standby-voltage = <850000>; + }; + + reg_vdd_3v3: BUCK4 { + regulator-name = "VDD_3V3"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <3400000>; + vin-supply = <®_5v_p>; + regulator-boot-on; + regulator-always-on; + }; + + reg_vdd_1v8: BUCK5 { + regulator-name = "VDD_1V8"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <3400000>; + vin-supply = <®_5v_p>; + regulator-boot-on; + regulator-always-on; + }; + + reg_nvcc_dram_1v1: BUCK6 { + regulator-name = "NVCC_DRAM_1V1"; + regulator-min-microvolt = <600000>; + regulator-max-microvolt = <3400000>; + vin-supply = <®_5v_p>; + regulator-boot-on; + regulator-always-on; + }; + + reg_nvcc_snvs_1v8: LDO1 { + regulator-name = "NVCC_SNVS_1V8"; + regulator-min-microvolt = <1600000>; + regulator-max-microvolt = <3300000>; + vin-supply = <®_5v_p>; + regulator-boot-on; + regulator-always-on; + }; + + reg_vdda_1v8: LDO3 { + regulator-name = "VDDA_1V8"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + vin-supply = <®_5v_p>; + regulator-boot-on; + regulator-always-on; + }; + + reg_nvcc_sd2: LDO5 { + regulator-name = "NVCC_SD2"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + vin-supply = <®_5v_p>; + regulator-boot-on; + regulator-always-on; + }; + }; + }; +}; + +&i2c3 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c3>; + status = "okay"; + + i2c_rtc: rtc@51 { + compatible = "nxp,pcf85063tp"; + reg = <0x51>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rtc>; + interrupts-extended = <&gpio4 31 IRQ_TYPE_EDGE_FALLING>; + quartz-load-femtofarads = <12500>; + }; +}; + +&i2c4 { + clock-frequency = <380000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c4>; + status = "okay"; + + switch: switch@5f { + compatible = "microchip,ksz9893"; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_switch>; + reset-gpios = <&gpio5 1 GPIO_ACTIVE_LOW>; + reg = <0x5f>; + + ethernet-ports { + #address-cells = <1>; + #size-cells = <0>; + + lan1: port@0 { + reg = <0>; + phy-mode = "internal"; + label = "lan1"; + }; + + lan2: port@1 { + reg = <1>; + phy-mode = "internal"; + label = "lan2"; + }; + + port@2 { + reg = <2>; + label = "cpu"; + ethernet = <&eqos>; + /* 2ns rgmii-rxid is implemented on PCB. + * Switch should add only rgmii-txid. + */ + phy-mode = "rgmii-txid"; + tx-internal-delay-ps = <2000>; + rx-internal-delay-ps = <0>; + + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; +}; + +&pwm1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm1>; +}; + +&pwm4 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_pwm4>; +}; + +&uart1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart1>; + status = "okay"; +}; + +&uart2 { + /* console */ + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_uart2>; + status = "okay"; +}; + +&usb3_0 { + status = "okay"; +}; + +&usb3_1 { + status = "okay"; +}; + +&usb3_phy0 { + vbus-supply = <®_3v3>; + status = "okay"; +}; + +&usb3_phy1 { + vbus-supply = <®_3v3>; + status = "okay"; +}; + +&usb_dwc3_0 { + dr_mode = "host"; +}; + +&usb_dwc3_1 { + dr_mode = "host"; +}; + +/* SD Card */ +&usdhc2 { + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc2>, <&pinctrl_usdhc2_gpio>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>, <&pinctrl_usdhc2_gpio>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>, <&pinctrl_usdhc2_gpio>; + vmmc-supply = <®_vsd_3v3>; + vqmmc-supply = <®_nvcc_sd2>; + cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>; + wp-gpios = <&gpio2 20 GPIO_ACTIVE_HIGH>; + bus-width = <4>; + status = "okay"; +}; + +/* eMMC */ +&usdhc3 { + assigned-clocks = <&clk IMX8MP_CLK_USDHC3>; + assigned-clock-rates = <400000000>; + pinctrl-names = "default", "state_100mhz", "state_200mhz"; + pinctrl-0 = <&pinctrl_usdhc3>; + pinctrl-1 = <&pinctrl_usdhc3_100mhz>; + pinctrl-2 = <&pinctrl_usdhc3_200mhz>; + vmmc-supply = <®_vdd_3v3>; + vqmmc-supply = <®_vdd_1v8>; + bus-width = <8>; + no-sd; + no-sdio; + non-removable; + status = "okay"; +}; + +&wdog1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_wdog>; + fsl,ext-reset-output; + status = "okay"; +}; + +&iomuxc { + pinctrl_backlight: backlightgrp { + fsl,pins = < + MX8MP_IOMUXC_SAI2_TXFS__GPIO4_IO24 0x0100 + >; + }; + + pinctrl_can2rs: can2rsgrp { + fsl,pins = < + MX8MP_IOMUXC_SAI2_RXC__GPIO4_IO22 0x154 + >; + }; + + pinctrl_canrs: canrsgrp { + fsl,pins = < + MX8MP_IOMUXC_SAI2_RXFS__GPIO4_IO21 0x154 + >; + }; + + pinctrl_ecspi2: ecspi2grp { + fsl,pins = < + MX8MP_IOMUXC_ECSPI2_SCLK__ECSPI2_SCLK 0x44 + MX8MP_IOMUXC_ECSPI2_MOSI__ECSPI2_MOSI 0x44 + MX8MP_IOMUXC_ECSPI2_MISO__ECSPI2_MISO 0x44 + MX8MP_IOMUXC_ECSPI2_SS0__GPIO5_IO13 0x40 + >; + }; + + pinctrl_eqos: eqosgrp { + fsl,pins = < + MX8MP_IOMUXC_ENET_RD0__ENET_QOS_RGMII_RD0 0x91 + MX8MP_IOMUXC_ENET_RD1__ENET_QOS_RGMII_RD1 0x91 + MX8MP_IOMUXC_ENET_RD2__ENET_QOS_RGMII_RD2 0x91 + MX8MP_IOMUXC_ENET_RD3__ENET_QOS_RGMII_RD3 0x91 + MX8MP_IOMUXC_ENET_RXC__CCM_ENET_QOS_CLOCK_GENERATE_RX_CLK 0x91 + MX8MP_IOMUXC_ENET_RX_CTL__ENET_QOS_RGMII_RX_CTL 0x91 + MX8MP_IOMUXC_ENET_TD0__ENET_QOS_RGMII_TD0 0x1f + MX8MP_IOMUXC_ENET_TD1__ENET_QOS_RGMII_TD1 0x1f + MX8MP_IOMUXC_ENET_TD2__ENET_QOS_RGMII_TD2 0x1f + MX8MP_IOMUXC_ENET_TD3__ENET_QOS_RGMII_TD3 0x1f + MX8MP_IOMUXC_ENET_TX_CTL__ENET_QOS_RGMII_TX_CTL 0x1f + MX8MP_IOMUXC_ENET_TXC__CCM_ENET_QOS_CLOCK_GENERATE_TX_CLK 0x1f + >; + }; + + pinctrl_flexcan1: flexcan1grp { + fsl,pins = < + MX8MP_IOMUXC_SPDIF_RX__CAN1_RX 0x154 + MX8MP_IOMUXC_SPDIF_TX__CAN1_TX 0x154 + >; + }; + + pinctrl_flexcan2: flexcan2grp { + fsl,pins = < + MX8MP_IOMUXC_SAI2_MCLK__CAN2_RX 0x154 + MX8MP_IOMUXC_SAI2_TXD0__CAN2_TX 0x154 + >; + }; + + pinctrl_gpio_led: gpioledgrp { + fsl,pins = < + MX8MP_IOMUXC_GPIO1_IO05__GPIO1_IO05 0x19 + MX8MP_IOMUXC_GPIO1_IO06__GPIO1_IO06 0x19 + MX8MP_IOMUXC_GPIO1_IO07__GPIO1_IO07 0x19 + >; + }; + + pinctrl_i2c1: i2c1grp { + fsl,pins = < + MX8MP_IOMUXC_I2C1_SCL__I2C1_SCL 0x400001c2 + MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA 0x400001c2 + >; + }; + + pinctrl_i2c3: i2c3grp { + fsl,pins = < + MX8MP_IOMUXC_I2C3_SCL__I2C3_SCL 0x400001c2 + MX8MP_IOMUXC_I2C3_SDA__I2C3_SDA 0x400001c2 + >; + }; + + pinctrl_i2c4: i2c4grp { + fsl,pins = < + MX8MP_IOMUXC_I2C4_SCL__I2C4_SCL 0x400001c3 + MX8MP_IOMUXC_I2C4_SDA__I2C4_SDA 0x400001c3 + >; + }; + + pinctrl_pmic: pmicirqgrp { + fsl,pins = < + MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03 0x41 + MX8MP_IOMUXC_GPIO1_IO04__GPIO1_IO04 0x41 + >; + }; + + pinctrl_pwm1: pwm1grp { + fsl,pins = < + MX8MP_IOMUXC_SPDIF_EXT_CLK__PWM1_OUT 0x116 + >; + }; + + pinctrl_pwm4: pwm4grp { + fsl,pins = < + MX8MP_IOMUXC_SAI3_MCLK__PWM4_OUT 0x116 + >; + }; + + pinctrl_reg_vsd_3v3: regvsd3v3grp { + fsl,pins = < + MX8MP_IOMUXC_SD2_RESET_B__GPIO2_IO19 0x40 + >; + }; + + pinctrl_rtc: rtcgrp { + fsl,pins = < + MX8MP_IOMUXC_SAI3_TXFS__GPIO4_IO31 0x41 + >; + }; + + pinctrl_switch: switchgrp { + fsl,pins = < + MX8MP_IOMUXC_SAI3_TXC__GPIO5_IO00 0x41 + MX8MP_IOMUXC_SAI3_TXD__GPIO5_IO01 0x41 + >; + }; + + pinctrl_touchscreen: touchscreengrp { + fsl,pins = < + /* external 10 k pull up */ + /* CTP_INT */ + MX8MP_IOMUXC_SAI3_RXFS__GPIO4_IO28 0x41 + /* CTP_RST */ + MX8MP_IOMUXC_SAI3_RXC__GPIO4_IO29 0x41 + >; + }; + + pinctrl_uart1: uart1grp { + fsl,pins = < + MX8MP_IOMUXC_UART1_RXD__UART1_DCE_RX 0x140 + MX8MP_IOMUXC_UART1_TXD__UART1_DCE_TX 0x140 + MX8MP_IOMUXC_UART3_RXD__UART1_DTE_RTS 0x140 + >; + }; + + pinctrl_uart2: uart2grp { + fsl,pins = < + MX8MP_IOMUXC_UART2_RXD__UART2_DCE_RX 0x14f + MX8MP_IOMUXC_UART2_TXD__UART2_DCE_TX 0x14f + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x190 + MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d0 + MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d0 + MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d0 + MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d0 + MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d0 + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp { + fsl,pins = < + MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x194 + MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d4 + MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d4 + MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d4 + MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d4 + MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d4 + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp { + fsl,pins = < + MX8MP_IOMUXC_SD2_CLK__USDHC2_CLK 0x196 + MX8MP_IOMUXC_SD2_CMD__USDHC2_CMD 0x1d6 + MX8MP_IOMUXC_SD2_DATA0__USDHC2_DATA0 0x1d6 + MX8MP_IOMUXC_SD2_DATA1__USDHC2_DATA1 0x1d6 + MX8MP_IOMUXC_SD2_DATA2__USDHC2_DATA2 0x1d6 + MX8MP_IOMUXC_SD2_DATA3__USDHC2_DATA3 0x1d6 + >; + }; + + pinctrl_usdhc2_gpio: usdhc2gpiogrp { + fsl,pins = < + MX8MP_IOMUXC_SD2_CD_B__GPIO2_IO12 0x1c4 + MX8MP_IOMUXC_SD2_WP__GPIO2_IO20 0x1c4 + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x190 + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d0 + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d0 + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d0 + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d0 + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d0 + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d0 + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d0 + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d0 + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d0 + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x190 + >; + }; + + pinctrl_usdhc3_100mhz: usdhc3-100mhzgrp { + fsl,pins = < + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x194 + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d4 + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d4 + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d4 + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d4 + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d4 + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d4 + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d4 + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d4 + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d4 + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x194 + >; + }; + + pinctrl_usdhc3_200mhz: usdhc3-200mhzgrp { + fsl,pins = < + MX8MP_IOMUXC_NAND_WE_B__USDHC3_CLK 0x196 + MX8MP_IOMUXC_NAND_WP_B__USDHC3_CMD 0x1d6 + MX8MP_IOMUXC_NAND_DATA04__USDHC3_DATA0 0x1d6 + MX8MP_IOMUXC_NAND_DATA05__USDHC3_DATA1 0x1d6 + MX8MP_IOMUXC_NAND_DATA06__USDHC3_DATA2 0x1d6 + MX8MP_IOMUXC_NAND_DATA07__USDHC3_DATA3 0x1d6 + MX8MP_IOMUXC_NAND_RE_B__USDHC3_DATA4 0x1d6 + MX8MP_IOMUXC_NAND_CE2_B__USDHC3_DATA5 0x1d6 + MX8MP_IOMUXC_NAND_CE3_B__USDHC3_DATA6 0x1d6 + MX8MP_IOMUXC_NAND_CLE__USDHC3_DATA7 0x1d6 + MX8MP_IOMUXC_NAND_CE1_B__USDHC3_STROBE 0x196 + >; + }; + + pinctrl_wdog: wdoggrp { + fsl,pins = < + MX8MP_IOMUXC_GPIO1_IO02__WDOG1_WDOG_B 0xc6 + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-skov-revb-hdmi.dts b/arch/arm64/boot/dts/freescale/imx8mp-skov-revb-hdmi.dts new file mode 100644 index 000000000000..c1ca69da3cb8 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mp-skov-revb-hdmi.dts @@ -0,0 +1,20 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) + +/dts-v1/; + +#include "imx8mp-skov-reva.dtsi" + +/ { + model = "SKOV IMX8MP CPU revB - HDMI"; + compatible = "skov,imx8mp-skov-revb-hdmi", "fsl,imx8mp"; +}; + +&iomuxc { + pinctrl_hdmi: hdmigrp { + fsl,pins = < + MX8MP_IOMUXC_HDMI_DDC_SCL__HDMIMIX_HDMI_SCL 0x1c3 + MX8MP_IOMUXC_HDMI_DDC_SDA__HDMIMIX_HDMI_SDA 0x1c3 + MX8MP_IOMUXC_HDMI_HPD__HDMIMIX_HDMI_HPD 0x19 + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-skov-revb-lt6.dts b/arch/arm64/boot/dts/freescale/imx8mp-skov-revb-lt6.dts new file mode 100644 index 000000000000..ccbd3abedd69 --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mp-skov-revb-lt6.dts @@ -0,0 +1,101 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) + +/dts-v1/; + +#include "imx8mp-skov-reva.dtsi" + +/ { + model = "SKOV IMX8MP CPU revB - LT6"; + compatible = "skov,imx8mp-skov-revb-lt6", "fsl,imx8mp"; + + touchscreen { + compatible = "resistive-adc-touch"; + io-channels = <&adc_ts 1>, <&adc_ts 3>, <&adc_ts 4>, <&adc_ts 5>; + io-channel-names = "y", "z1", "z2", "x"; + touchscreen-min-pressure = <65000>; + touchscreen-inverted-y; + touchscreen-swapped-x-y; + touchscreen-x-plate-ohms = <300>; + }; +}; + +®_tft_vcom { + regulator-min-microvolt = <3600000>; + regulator-max-microvolt = <3600000>; + voltage-table = <3600000 26>; + status = "okay"; +}; + +&pwm4 { + status = "okay"; +}; + +&backlight { + status = "okay"; +}; + +&ecspi1 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_ecspi1>; + cs-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>; + status = "okay"; + + adc_ts: adc@0 { + compatible = "ti,tsc2046e-adc"; + reg = <0>; + pinctrl-0 = <&pinctrl_touch>; + pinctrl-names ="default"; + spi-max-frequency = <1000000>; + interrupts-extended = <&gpio4 25 IRQ_TYPE_LEVEL_LOW>; + #io-channel-cells = <1>; + + #address-cells = <1>; + #size-cells = <0>; + + channel@1 { + reg = <1>; + settling-time-us = <700>; + oversampling-ratio = <5>; + }; + + channel@3 { + reg = <3>; + settling-time-us = <700>; + oversampling-ratio = <5>; + }; + + channel@4 { + reg = <4>; + settling-time-us = <700>; + oversampling-ratio = <5>; + }; + + channel@5 { + reg = <5>; + settling-time-us = <700>; + oversampling-ratio = <5>; + }; + }; +}; + +&pwm1 { + status = "okay"; +}; + +&iomuxc { + pinctrl_ecspi1: ecspi1grp { + fsl,pins = < + MX8MP_IOMUXC_ECSPI1_SCLK__ECSPI1_SCLK 0x44 + MX8MP_IOMUXC_ECSPI1_MOSI__ECSPI1_MOSI 0x44 + MX8MP_IOMUXC_ECSPI1_MISO__ECSPI1_MISO 0x44 + MX8MP_IOMUXC_ECSPI1_SS0__GPIO5_IO09 0x40 + >; + }; + + pinctrl_touch: touchgrp { + fsl,pins = < + /* external pull up */ + MX8MP_IOMUXC_SAI2_TXC__GPIO4_IO25 0x40 + >; + }; +}; diff --git a/arch/arm64/boot/dts/freescale/imx8mp-skov-revb-mi1010ait-1cp1.dts b/arch/arm64/boot/dts/freescale/imx8mp-skov-revb-mi1010ait-1cp1.dts new file mode 100644 index 000000000000..3c2efdc59bfa --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx8mp-skov-revb-mi1010ait-1cp1.dts @@ -0,0 +1,100 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) + +/dts-v1/; + +#include "imx8mp-skov-reva.dtsi" + +/ { + model = "SKOV IMX8MP CPU revB - MI1010AIT-1CP1"; + compatible = "skov,imx8mp-skov-revb-mi1010ait-1cp1", "fsl,imx8mp"; + + panel { + compatible = "multi-inno,mi1010ait-1cp"; + backlight = <&backlight>; + power-supply = <®_tft_vcom>; + + port { + in_lvds0: endpoint { + remote-endpoint = <&ldb_lvds_ch0>; + }; + }; + }; +}; + +&backlight { + status = "okay"; +}; + +&i2c2 { + clock-frequency = <100000>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_i2c2>; + status = "okay"; + + touchscreen@38 { + compatible = "edt,edt-ft5406"; + reg = <0x38>; + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_touchscreen>; + interrupts-extended = <&gpio4 28 IRQ_TYPE_EDGE_FALLING>; + reset-gpios = <&gpio4 29 GPIO_ACTIVE_LOW>; + touchscreen-size-x = <1280>; + touchscreen-size-y = <800>; + vcc-supply = <®_vdd_3v3>; + iovcc-supply = <®_vdd_3v3>; + wakeup-source; + }; +}; + +&lcdif2 { + status = "okay"; +}; + +&lvds_bridge { + /* IMX8MP_CLK_MEDIA_LDB = IMX8MP_CLK_MEDIA_DISP2_PIX * 7 */ + assigned-clock-rates = <482300000>; + status = "okay"; + + ports { + port@1 { + ldb_lvds_ch0: endpoint { + remote-endpoint = <&in_lvds0>; + }; + }; + }; +}; + +&media_blk_ctrl { + /* currently it is not possible to let display clocks confugure + * automatically, so we need to set them manually + */ + assigned-clock-rates = <500000000>, <200000000>, <0>, + /* IMX8MP_CLK_MEDIA_DISP2_PIX = pixelclk of lvds panel */ + <68900000>, + /* IMX8MP_VIDEO_PLL1 = IMX8MP_CLK_MEDIA_LDB * 2 */ + <964600000>; +}; + +&pwm4 { + status = "okay"; +}; + +&pwm1 { + status = "okay"; +}; + +®_tft_vcom { + regulator-min-microvolt = <3160000>; + regulator-max-microvolt = <3160000>; + voltage-table = <3160000 73>; + status = "okay"; +}; + +&iomuxc { + pinctrl_i2c2: i2c2grp { + fsl,pins = < + MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL 0x400001c2 + MX8MP_IOMUXC_I2C2_SDA__I2C2_SDA 0x400001c2 + >; + }; +}; -- 2.39.2 ^ permalink raw reply related [flat|nested] 16+ messages in thread
* Re: [PATCH v2 2/2] arm64: dts: freescale: Add SKOV IMX8MP CPU revB board 2023-11-03 10:53 ` Oleksij Rempel @ 2023-11-03 12:35 ` Andrew Lunn -1 siblings, 0 replies; 16+ messages in thread From: Andrew Lunn @ 2023-11-03 12:35 UTC (permalink / raw) To: Oleksij Rempel Cc: Shawn Guo, Sascha Hauer, Rob Herring, Krzysztof Kozlowski, Søren Andersen, Sam Ravnborg, kernel, linux-kernel, devicetree, linux-arm-kernel, NXP Linux Team, Fabio Estevam > + port@2 { > + reg = <2>; > + label = "cpu"; > + ethernet = <&eqos>; > + /* 2ns rgmii-rxid is implemented on PCB. > + * Switch should add only rgmii-txid. > + */ Its unusual to actually see that. Its even more unusual its only one clock line. Can you actually see it on the PCB? > + phy-mode = "rgmii-txid"; > + tx-internal-delay-ps = <2000>; Is this actually needed? rgmii-txid should add 2ns delay. Since this apparently works, i'm assuming setting tx-internal-delay-ps to 2ns does nothing, otherwise you would have a 4ns delay. Andrew _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH v2 2/2] arm64: dts: freescale: Add SKOV IMX8MP CPU revB board @ 2023-11-03 12:35 ` Andrew Lunn 0 siblings, 0 replies; 16+ messages in thread From: Andrew Lunn @ 2023-11-03 12:35 UTC (permalink / raw) To: Oleksij Rempel Cc: Shawn Guo, Sascha Hauer, Rob Herring, Krzysztof Kozlowski, Søren Andersen, Sam Ravnborg, kernel, linux-kernel, devicetree, linux-arm-kernel, NXP Linux Team, Fabio Estevam > + port@2 { > + reg = <2>; > + label = "cpu"; > + ethernet = <&eqos>; > + /* 2ns rgmii-rxid is implemented on PCB. > + * Switch should add only rgmii-txid. > + */ Its unusual to actually see that. Its even more unusual its only one clock line. Can you actually see it on the PCB? > + phy-mode = "rgmii-txid"; > + tx-internal-delay-ps = <2000>; Is this actually needed? rgmii-txid should add 2ns delay. Since this apparently works, i'm assuming setting tx-internal-delay-ps to 2ns does nothing, otherwise you would have a 4ns delay. Andrew ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH v2 2/2] arm64: dts: freescale: Add SKOV IMX8MP CPU revB board 2023-11-03 12:35 ` Andrew Lunn @ 2023-11-03 12:53 ` Oleksij Rempel -1 siblings, 0 replies; 16+ messages in thread From: Oleksij Rempel @ 2023-11-03 12:53 UTC (permalink / raw) To: Andrew Lunn Cc: devicetree, Fabio Estevam, kernel, Shawn Guo, Sascha Hauer, linux-kernel, Rob Herring, NXP Linux Team, Krzysztof Kozlowski, Søren Andersen, Sam Ravnborg, linux-arm-kernel Hi Andrew, On Fri, Nov 03, 2023 at 01:35:46PM +0100, Andrew Lunn wrote: > > + port@2 { > > + reg = <2>; > > + label = "cpu"; > > + ethernet = <&eqos>; > > + /* 2ns rgmii-rxid is implemented on PCB. > > + * Switch should add only rgmii-txid. > > + */ > > Its unusual to actually see that. Its even more unusual its only one > clock line. Can you actually see it on the PCB? Yes. I even made a delay calculation by measuring this trace on PCB, just to make sure I see it correctly. > > + phy-mode = "rgmii-txid"; > > + tx-internal-delay-ps = <2000>; > > Is this actually needed? rgmii-txid should add 2ns delay. Since this > apparently works, i'm assuming setting tx-internal-delay-ps to 2ns > does nothing, otherwise you would have a 4ns delay. Without it the driver will complain: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/net/dsa/microchip/ksz_common.c?h=v6.6#n3496 but it works as expected. Regards, Oleksij -- Pengutronix e.K. | | Steuerwalder Str. 21 | http://www.pengutronix.de/ | 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH v2 2/2] arm64: dts: freescale: Add SKOV IMX8MP CPU revB board @ 2023-11-03 12:53 ` Oleksij Rempel 0 siblings, 0 replies; 16+ messages in thread From: Oleksij Rempel @ 2023-11-03 12:53 UTC (permalink / raw) To: Andrew Lunn Cc: devicetree, Fabio Estevam, kernel, Shawn Guo, Sascha Hauer, linux-kernel, Rob Herring, NXP Linux Team, Krzysztof Kozlowski, Søren Andersen, Sam Ravnborg, linux-arm-kernel Hi Andrew, On Fri, Nov 03, 2023 at 01:35:46PM +0100, Andrew Lunn wrote: > > + port@2 { > > + reg = <2>; > > + label = "cpu"; > > + ethernet = <&eqos>; > > + /* 2ns rgmii-rxid is implemented on PCB. > > + * Switch should add only rgmii-txid. > > + */ > > Its unusual to actually see that. Its even more unusual its only one > clock line. Can you actually see it on the PCB? Yes. I even made a delay calculation by measuring this trace on PCB, just to make sure I see it correctly. > > + phy-mode = "rgmii-txid"; > > + tx-internal-delay-ps = <2000>; > > Is this actually needed? rgmii-txid should add 2ns delay. Since this > apparently works, i'm assuming setting tx-internal-delay-ps to 2ns > does nothing, otherwise you would have a 4ns delay. Without it the driver will complain: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/net/dsa/microchip/ksz_common.c?h=v6.6#n3496 but it works as expected. Regards, Oleksij -- Pengutronix e.K. | | Steuerwalder Str. 21 | http://www.pengutronix.de/ | 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH v2 2/2] arm64: dts: freescale: Add SKOV IMX8MP CPU revB board 2023-11-03 12:53 ` Oleksij Rempel @ 2023-11-03 13:15 ` Andrew Lunn -1 siblings, 0 replies; 16+ messages in thread From: Andrew Lunn @ 2023-11-03 13:15 UTC (permalink / raw) To: Oleksij Rempel Cc: devicetree, Fabio Estevam, kernel, Shawn Guo, Sascha Hauer, linux-kernel, Rob Herring, NXP Linux Team, Krzysztof Kozlowski, Søren Andersen, Sam Ravnborg, linux-arm-kernel On Fri, Nov 03, 2023 at 01:53:06PM +0100, Oleksij Rempel wrote: > Hi Andrew, > > On Fri, Nov 03, 2023 at 01:35:46PM +0100, Andrew Lunn wrote: > > > + port@2 { > > > + reg = <2>; > > > + label = "cpu"; > > > + ethernet = <&eqos>; > > > + /* 2ns rgmii-rxid is implemented on PCB. > > > + * Switch should add only rgmii-txid. > > > + */ > > > > Its unusual to actually see that. Its even more unusual its only one > > clock line. Can you actually see it on the PCB? > > Yes. I even made a delay calculation by measuring this trace on PCB, > just to make sure I see it correctly. Cool. I need to keep this board in mind, its about the only one i know of which actually does this. > > > + phy-mode = "rgmii-txid"; > > > + tx-internal-delay-ps = <2000>; > > > > Is this actually needed? rgmii-txid should add 2ns delay. Since this > > apparently works, i'm assuming setting tx-internal-delay-ps to 2ns > > does nothing, otherwise you would have a 4ns delay. > > Without it the driver will complain: > https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/net/dsa/microchip/ksz_common.c?h=v6.6#n3496 Ah! Humm. I forget how this all works. This is the port node, not the PHY. We are configuring the MAC delays with tx-internal-delay-ps. There is no PHY here, so phy-mode is not used by any PHY. All that might matter is that you indicate rgmii or some sort. Have you tried plain "rgmii". It then looks less like you have 4ns of delay. Andrew _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH v2 2/2] arm64: dts: freescale: Add SKOV IMX8MP CPU revB board @ 2023-11-03 13:15 ` Andrew Lunn 0 siblings, 0 replies; 16+ messages in thread From: Andrew Lunn @ 2023-11-03 13:15 UTC (permalink / raw) To: Oleksij Rempel Cc: devicetree, Fabio Estevam, kernel, Shawn Guo, Sascha Hauer, linux-kernel, Rob Herring, NXP Linux Team, Krzysztof Kozlowski, Søren Andersen, Sam Ravnborg, linux-arm-kernel On Fri, Nov 03, 2023 at 01:53:06PM +0100, Oleksij Rempel wrote: > Hi Andrew, > > On Fri, Nov 03, 2023 at 01:35:46PM +0100, Andrew Lunn wrote: > > > + port@2 { > > > + reg = <2>; > > > + label = "cpu"; > > > + ethernet = <&eqos>; > > > + /* 2ns rgmii-rxid is implemented on PCB. > > > + * Switch should add only rgmii-txid. > > > + */ > > > > Its unusual to actually see that. Its even more unusual its only one > > clock line. Can you actually see it on the PCB? > > Yes. I even made a delay calculation by measuring this trace on PCB, > just to make sure I see it correctly. Cool. I need to keep this board in mind, its about the only one i know of which actually does this. > > > + phy-mode = "rgmii-txid"; > > > + tx-internal-delay-ps = <2000>; > > > > Is this actually needed? rgmii-txid should add 2ns delay. Since this > > apparently works, i'm assuming setting tx-internal-delay-ps to 2ns > > does nothing, otherwise you would have a 4ns delay. > > Without it the driver will complain: > https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/net/dsa/microchip/ksz_common.c?h=v6.6#n3496 Ah! Humm. I forget how this all works. This is the port node, not the PHY. We are configuring the MAC delays with tx-internal-delay-ps. There is no PHY here, so phy-mode is not used by any PHY. All that might matter is that you indicate rgmii or some sort. Have you tried plain "rgmii". It then looks less like you have 4ns of delay. Andrew ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH v2 2/2] arm64: dts: freescale: Add SKOV IMX8MP CPU revB board 2023-11-03 12:35 ` Andrew Lunn @ 2023-11-03 13:16 ` Russell King (Oracle) -1 siblings, 0 replies; 16+ messages in thread From: Russell King (Oracle) @ 2023-11-03 13:16 UTC (permalink / raw) To: Andrew Lunn Cc: Oleksij Rempel, Shawn Guo, Sascha Hauer, Rob Herring, Krzysztof Kozlowski, Søren Andersen, Sam Ravnborg, kernel, linux-kernel, devicetree, linux-arm-kernel, NXP Linux Team, Fabio Estevam On Fri, Nov 03, 2023 at 01:35:46PM +0100, Andrew Lunn wrote: > > + port@2 { > > + reg = <2>; > > + label = "cpu"; > > + ethernet = <&eqos>; > > + /* 2ns rgmii-rxid is implemented on PCB. > > + * Switch should add only rgmii-txid. > > + */ > > Its unusual to actually see that. Its even more unusual its only one > clock line. Can you actually see it on the PCB? > > > + phy-mode = "rgmii-txid"; > > + tx-internal-delay-ps = <2000>; > > Is this actually needed? rgmii-txid should add 2ns delay. Since this > apparently works, i'm assuming setting tx-internal-delay-ps to 2ns > does nothing, otherwise you would have a 4ns delay. Umm... I think we're getting confused again. Mode Local end Remote end RGMII No added delays No added delays RGMII-TXID No added delays 2ns delay on TX RGMII-RXID No added delays 2ns delay on RX RGMII-ID No added delays 2ns delay on both TX and RX In the case of a network interface with a PHY, "local end" is the MAC and "remote end" is the PHY. For a switch port connected to an external PHY, the switch port is as the "MAC" as above. For a switch port connected to an ethernet MAC: - for the MAC declaration, the local end is the MAC. There is no communication of the interface mode with the remote end under Linux, so this is irrelevant for Linux. However, this is an implementation, and it should be chosen according to the hardware. - for the switch port declaration, the local end is the switch port. There is no communication of the interface mode with the remote end under Linux. However, it should be chosen according to the hardware. So, if the 2ns delay is implemented on the RX lines (from the switch perspective) then shouldn't the MAC side be using "rgmii-txid" to indicate that the delay is being applied by the remote end (switch). The switch side should be using "rgmii" because no delays are required from the remote end (MAC), and the delay on the TX lines should be specified using "tx-internal-delay-ps"? -- RMK's Patch system: https://www.armlinux.org.uk/developer/patches/ FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last! _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH v2 2/2] arm64: dts: freescale: Add SKOV IMX8MP CPU revB board @ 2023-11-03 13:16 ` Russell King (Oracle) 0 siblings, 0 replies; 16+ messages in thread From: Russell King (Oracle) @ 2023-11-03 13:16 UTC (permalink / raw) To: Andrew Lunn Cc: Oleksij Rempel, Shawn Guo, Sascha Hauer, Rob Herring, Krzysztof Kozlowski, Søren Andersen, Sam Ravnborg, kernel, linux-kernel, devicetree, linux-arm-kernel, NXP Linux Team, Fabio Estevam On Fri, Nov 03, 2023 at 01:35:46PM +0100, Andrew Lunn wrote: > > + port@2 { > > + reg = <2>; > > + label = "cpu"; > > + ethernet = <&eqos>; > > + /* 2ns rgmii-rxid is implemented on PCB. > > + * Switch should add only rgmii-txid. > > + */ > > Its unusual to actually see that. Its even more unusual its only one > clock line. Can you actually see it on the PCB? > > > + phy-mode = "rgmii-txid"; > > + tx-internal-delay-ps = <2000>; > > Is this actually needed? rgmii-txid should add 2ns delay. Since this > apparently works, i'm assuming setting tx-internal-delay-ps to 2ns > does nothing, otherwise you would have a 4ns delay. Umm... I think we're getting confused again. Mode Local end Remote end RGMII No added delays No added delays RGMII-TXID No added delays 2ns delay on TX RGMII-RXID No added delays 2ns delay on RX RGMII-ID No added delays 2ns delay on both TX and RX In the case of a network interface with a PHY, "local end" is the MAC and "remote end" is the PHY. For a switch port connected to an external PHY, the switch port is as the "MAC" as above. For a switch port connected to an ethernet MAC: - for the MAC declaration, the local end is the MAC. There is no communication of the interface mode with the remote end under Linux, so this is irrelevant for Linux. However, this is an implementation, and it should be chosen according to the hardware. - for the switch port declaration, the local end is the switch port. There is no communication of the interface mode with the remote end under Linux. However, it should be chosen according to the hardware. So, if the 2ns delay is implemented on the RX lines (from the switch perspective) then shouldn't the MAC side be using "rgmii-txid" to indicate that the delay is being applied by the remote end (switch). The switch side should be using "rgmii" because no delays are required from the remote end (MAC), and the delay on the TX lines should be specified using "tx-internal-delay-ps"? -- RMK's Patch system: https://www.armlinux.org.uk/developer/patches/ FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last! ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH v2 2/2] arm64: dts: freescale: Add SKOV IMX8MP CPU revB board 2023-11-03 13:16 ` Russell King (Oracle) @ 2023-11-03 19:16 ` Oleksij Rempel -1 siblings, 0 replies; 16+ messages in thread From: Oleksij Rempel @ 2023-11-03 19:16 UTC (permalink / raw) To: Russell King (Oracle) Cc: Andrew Lunn, Shawn Guo, Sascha Hauer, Rob Herring, Krzysztof Kozlowski, Søren Andersen, Sam Ravnborg, kernel, linux-kernel, devicetree, linux-arm-kernel, NXP Linux Team, Fabio Estevam On Fri, Nov 03, 2023 at 01:16:12PM +0000, Russell King (Oracle) wrote: > On Fri, Nov 03, 2023 at 01:35:46PM +0100, Andrew Lunn wrote: > > > + port@2 { > > > + reg = <2>; > > > + label = "cpu"; > > > + ethernet = <&eqos>; > > > + /* 2ns rgmii-rxid is implemented on PCB. > > > + * Switch should add only rgmii-txid. > > > + */ > > > > Its unusual to actually see that. Its even more unusual its only one > > clock line. Can you actually see it on the PCB? > > > > > + phy-mode = "rgmii-txid"; > > > + tx-internal-delay-ps = <2000>; > > > > Is this actually needed? rgmii-txid should add 2ns delay. Since this > > apparently works, i'm assuming setting tx-internal-delay-ps to 2ns > > does nothing, otherwise you would have a 4ns delay. > > Umm... I think we're getting confused again. > > Mode Local end Remote end > RGMII No added delays No added delays > RGMII-TXID No added delays 2ns delay on TX > RGMII-RXID No added delays 2ns delay on RX > RGMII-ID No added delays 2ns delay on both TX and RX > > In the case of a network interface with a PHY, "local end" is the > MAC and "remote end" is the PHY. > > For a switch port connected to an external PHY, the switch port is > as the "MAC" as above. > > For a switch port connected to an ethernet MAC: > - for the MAC declaration, the local end is the MAC. There is no > communication of the interface mode with the remote end under > Linux, so this is irrelevant for Linux. However, this is an > implementation, and it should be chosen according to the hardware. > > - for the switch port declaration, the local end is the switch port. > There is no communication of the interface mode with the remote > end under Linux. However, it should be chosen according to the > hardware. > > So, if the 2ns delay is implemented on the RX lines (from the switch > perspective) then shouldn't the MAC side be using "rgmii-txid" to > indicate that the delay is being applied by the remote end (switch). > The switch side should be using "rgmii" because no delays are required > from the remote end (MAC), and the delay on the TX lines should be > specified using "tx-internal-delay-ps"? Ack. It make sense. Will fix it. Regards, Oleksij -- Pengutronix e.K. | | Steuerwalder Str. 21 | http://www.pengutronix.de/ | 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH v2 2/2] arm64: dts: freescale: Add SKOV IMX8MP CPU revB board @ 2023-11-03 19:16 ` Oleksij Rempel 0 siblings, 0 replies; 16+ messages in thread From: Oleksij Rempel @ 2023-11-03 19:16 UTC (permalink / raw) To: Russell King (Oracle) Cc: Andrew Lunn, Shawn Guo, Sascha Hauer, Rob Herring, Krzysztof Kozlowski, Søren Andersen, Sam Ravnborg, kernel, linux-kernel, devicetree, linux-arm-kernel, NXP Linux Team, Fabio Estevam On Fri, Nov 03, 2023 at 01:16:12PM +0000, Russell King (Oracle) wrote: > On Fri, Nov 03, 2023 at 01:35:46PM +0100, Andrew Lunn wrote: > > > + port@2 { > > > + reg = <2>; > > > + label = "cpu"; > > > + ethernet = <&eqos>; > > > + /* 2ns rgmii-rxid is implemented on PCB. > > > + * Switch should add only rgmii-txid. > > > + */ > > > > Its unusual to actually see that. Its even more unusual its only one > > clock line. Can you actually see it on the PCB? > > > > > + phy-mode = "rgmii-txid"; > > > + tx-internal-delay-ps = <2000>; > > > > Is this actually needed? rgmii-txid should add 2ns delay. Since this > > apparently works, i'm assuming setting tx-internal-delay-ps to 2ns > > does nothing, otherwise you would have a 4ns delay. > > Umm... I think we're getting confused again. > > Mode Local end Remote end > RGMII No added delays No added delays > RGMII-TXID No added delays 2ns delay on TX > RGMII-RXID No added delays 2ns delay on RX > RGMII-ID No added delays 2ns delay on both TX and RX > > In the case of a network interface with a PHY, "local end" is the > MAC and "remote end" is the PHY. > > For a switch port connected to an external PHY, the switch port is > as the "MAC" as above. > > For a switch port connected to an ethernet MAC: > - for the MAC declaration, the local end is the MAC. There is no > communication of the interface mode with the remote end under > Linux, so this is irrelevant for Linux. However, this is an > implementation, and it should be chosen according to the hardware. > > - for the switch port declaration, the local end is the switch port. > There is no communication of the interface mode with the remote > end under Linux. However, it should be chosen according to the > hardware. > > So, if the 2ns delay is implemented on the RX lines (from the switch > perspective) then shouldn't the MAC side be using "rgmii-txid" to > indicate that the delay is being applied by the remote end (switch). > The switch side should be using "rgmii" because no delays are required > from the remote end (MAC), and the delay on the TX lines should be > specified using "tx-internal-delay-ps"? Ack. It make sense. Will fix it. Regards, Oleksij -- Pengutronix e.K. | | Steuerwalder Str. 21 | http://www.pengutronix.de/ | 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 | Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 | ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH v2 1/2] dt-bindings: arm: Add compatible for SKOV i.MX8MP RevB board 2023-11-03 10:53 ` Oleksij Rempel @ 2023-11-03 11:50 ` Krzysztof Kozlowski -1 siblings, 0 replies; 16+ messages in thread From: Krzysztof Kozlowski @ 2023-11-03 11:50 UTC (permalink / raw) To: Oleksij Rempel, Shawn Guo, Sascha Hauer, Rob Herring, Krzysztof Kozlowski, Søren Andersen, Sam Ravnborg Cc: kernel, linux-kernel, devicetree, linux-arm-kernel, NXP Linux Team, Fabio Estevam On 03/11/2023 11:53, Oleksij Rempel wrote: > Add DT compatible string for a SKOV i.MX8MP RevB climate controller board. > > Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> > --- Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Best regards, Krzysztof _______________________________________________ linux-arm-kernel mailing list linux-arm-kernel@lists.infradead.org http://lists.infradead.org/mailman/listinfo/linux-arm-kernel ^ permalink raw reply [flat|nested] 16+ messages in thread
* Re: [PATCH v2 1/2] dt-bindings: arm: Add compatible for SKOV i.MX8MP RevB board @ 2023-11-03 11:50 ` Krzysztof Kozlowski 0 siblings, 0 replies; 16+ messages in thread From: Krzysztof Kozlowski @ 2023-11-03 11:50 UTC (permalink / raw) To: Oleksij Rempel, Shawn Guo, Sascha Hauer, Rob Herring, Krzysztof Kozlowski, Søren Andersen, Sam Ravnborg Cc: kernel, linux-kernel, devicetree, linux-arm-kernel, NXP Linux Team, Fabio Estevam On 03/11/2023 11:53, Oleksij Rempel wrote: > Add DT compatible string for a SKOV i.MX8MP RevB climate controller board. > > Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> > --- Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Best regards, Krzysztof ^ permalink raw reply [flat|nested] 16+ messages in thread
end of thread, other threads:[~2023-11-03 19:17 UTC | newest] Thread overview: 16+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2023-11-03 10:53 [PATCH v2 1/2] dt-bindings: arm: Add compatible for SKOV i.MX8MP RevB board Oleksij Rempel 2023-11-03 10:53 ` Oleksij Rempel 2023-11-03 10:53 ` [PATCH v2 2/2] arm64: dts: freescale: Add SKOV IMX8MP CPU revB board Oleksij Rempel 2023-11-03 10:53 ` Oleksij Rempel 2023-11-03 12:35 ` Andrew Lunn 2023-11-03 12:35 ` Andrew Lunn 2023-11-03 12:53 ` Oleksij Rempel 2023-11-03 12:53 ` Oleksij Rempel 2023-11-03 13:15 ` Andrew Lunn 2023-11-03 13:15 ` Andrew Lunn 2023-11-03 13:16 ` Russell King (Oracle) 2023-11-03 13:16 ` Russell King (Oracle) 2023-11-03 19:16 ` Oleksij Rempel 2023-11-03 19:16 ` Oleksij Rempel 2023-11-03 11:50 ` [PATCH v2 1/2] dt-bindings: arm: Add compatible for SKOV i.MX8MP RevB board Krzysztof Kozlowski 2023-11-03 11:50 ` Krzysztof Kozlowski
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.