Re: [RFC PATCH 2/2] net: phy: mxl-gpy: add new device tree property to disable SGMII autoneg

["Russell King (Oracle)" <linux@armlinux.org.uk>]

On Fri, May 03, 2024 at 06:35:53PM +0200, Stefan Eichenberger wrote:
> On Thu, May 02, 2024 at 03:14:13PM +0100, Russell King (Oracle) wrote:
> > On Thu, May 02, 2024 at 03:44:24PM +0200, Stefan Eichenberger wrote:
> > > Hi Russell,
> > > 
> > > Sorry for the late reply but I wanted to give you some update after
> > > testing with the latest version of your patches on net-queue.
> > 
> > I've also been randomly distracted, and I've been meaning to ping you
> > to test some of the updates.
> > 
> > http://git.armlinux.org.uk/cgit/linux-arm.git/log/?h=net-queue
> > 
> > The current set begins with:
> > 
> > "net: sfp-bus: constify link_modes to sfp_select_interface()" which is
> > now in net-next, then the patches between and including:
> > 
> > "net: phylink: validate sfp_select_interface() returned interface" to
> > "net: phylink: clean up phylink_resolve()"
> > 
> > That should get enough together for the PCS "neg" mode to be consistent
> > with what the MAC driver sees.
> > 
> > The remaining bits that I still need to sort out is the contents of
> > phylink_pcs_neg_mode() for the 802.3z mode with PHY, and also working
> > out some way of handling the SGMII case where the PHY and PCS disagree
> > (one only supporting inband the other not supporting inband.)
> > 
> > I'm not sure when I'll be able to get to that - things are getting
> > fairly chaotic again, meaning I have again less time to spend on
> > mainline... and I'd like to take some vacation time very soon (I really
> > need some time off!)
> 
> No problem, I'm also quite busy at the moment and I have the workaround
> to test the hardware, so it is nothing urgent for me.
> 
> > > I think I see the problem you are describing.
> > > 
> > > When the driver starts it will negotiate MLO_AN_PHY based on the
> > > capabilities of the PHY and of the PCS. However when I switch to 1GBit/s
> > > it should switch to MLO_AN_INBAND but this does not work. Here the
> > > output of phylink:
> > 
> > I'm designing this to work the other way - inband being able to fall
> > back to PHY (out of band) mode rather than PHY mode being able to fall
> > forwards to inband mode.
> 
> I tested again with 89e0a87ef79db9f3ce879e9d977429ba89ca8229 and I think
> in my setup the problem is that it doesn't fall back to PHY mode but
> takes it as default mode. Here what happens when I have the mxl-gpy PHY
> connected to a 1000 GBit/s port:
> [    9.331179] mvpp2 f2000000.ethernet eth1: Using firmware node mac address 00:51:82:11:22:02
> [   14.674836] mvpp2 f2000000.ethernet eth1: PHY f212a600.mdio-mii:11 doesn't supply possible interfaces
> [   14.674853] mvpp2 f2000000.ethernet eth1:  interface 2 (mii) rate match none supports 0-3,6,13-14
> [   14.674864] mvpp2 f2000000.ethernet eth1:  interface 4 (sgmii) rate match none supports 0-3,5-6,13-14
> [   14.674871] mvpp2 f2000000.ethernet eth1:  interface 9 (rgmii) rate match none supports 0-3,5-6,13-14
> [   14.674877] mvpp2 f2000000.ethernet eth1:  interface 10 (rgmii-id) rate match none supports 0-3,5-6,13-14
> [   14.674883] mvpp2 f2000000.ethernet eth1:  interface 11 (rgmii-rxid) rate match none supports 0-3,5-6,13-14
> [   14.674889] mvpp2 f2000000.ethernet eth1:  interface 12 (rgmii-txid) rate match none supports 0-3,5-6,13-14
> [   14.674895] mvpp2 f2000000.ethernet eth1:  interface 22 (1000base-x) rate match none supports 5-6,13-14
> [   14.674900] mvpp2 f2000000.ethernet eth1:  interface 23 (2500base-x) rate match none supports 6,13-14,47
> [   14.674907] mvpp2 f2000000.ethernet eth1: PHY [f212a600.mdio-mii:11] driver [Maxlinear Ethernet GPY215C] (irq=POLL)
> [   14.685444] mvpp2 f2000000.ethernet eth1: phy: 2500base-x setting supported 00,00000000,00008000,0000606f advertising 00,00000000,00008000,0000606f
> [   14.686635] mvpp2 f2000000.ethernet eth1: configuring for phy/2500base-x link mode
> [   14.694263] mvpp2 f2000000.ethernet eth1: major config, requested phy/2500base-x

                                                                       ^^^

You're still requesting (from firmware) for PHY mode, and phylink will
_always_ use out-of-band if firmware requests that.

> [   14.700402] mvpp2 f2000000.ethernet eth1: major config, active phy/outband/2500base-x

So it uses PHY mode for 2500base-X, which is correct.

> [   17.768370] mvpp2 f2000000.ethernet eth1: major config, requested phy/sgmii

Still requesting PHY mode with SGMII, which historically we've always
used out-of-band mode for, so we preserve that behaviour.

> [   17.774602] mvpp2 f2000000.ethernet eth1: firmware wants phy mode, but PHY requires inband

So we complain about it with an error, because it is wrong...

> [   17.782976] mvpp2 f2000000.ethernet eth1: major config, active phy/outband/sgmii

and we still try to use it (correctly, because that's what phylink
has always done in this case.)

As I tried to explain, there is fall-back from MLO_AN_INBAND to
MLO_AN_PHY, but there won't be fall-forward from MLO_AN_PHY to
MLO_AN_INBAND.

-- 
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!