From: miles.lane@gmail.com (Miles Lane)
To: lm-sensors@vger.kernel.org
Subject: Who should I write to about this OOPS in 2,6,11-mm3?
Date: Thu, 19 May 2005 06:25:45 +0000 [thread overview]
Message-ID: <a44ae5cd05032309522218e97e@mail.gmail.com> (raw)
In-Reply-To: <20050315050746.GB13009@kroah.com>
I tried compiling the nvidiafb driver as a module. I was able to boot
the machine successfully and then both add and remove the driver.
However, when I modprobe the driver, I get the following error:
ACPI: PCI Interrupt Link [APC4] enabled at IRQ 19
ACPI: PCI interrupt 0000:03:00.0[A] -> GSI 19 (level, high) -> IRQ 19
PCI: Unable to reserve mem region #2:10000000@d0000000 for device 0000:03:00.0
nvidiafb: cannot request PCI regions
Here is the output of lspci -vv (I hope this is helpful information):
0000:00:00.0 Host bridge: nVidia Corporation nForce2 AGP (different
version?) (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at e0000000 (32-bit, prefetchable) [size\x128M]
Capabilities: [40] AGP version 3.0
Status: RQ2 Iso- ArqSz=2 Cal=0 SBA+ ITACoh- GART64-
HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=x4
Capabilities: [60] #08 [2001]
0000:00:00.1 RAM memory: nVidia Corporation nForce2 Memory Controller 1 (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:00.2 RAM memory: nVidia Corporation nForce2 Memory Controller 4 (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:00.3 RAM memory: nVidia Corporation nForce2 Memory Controller 3 (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:00.4 RAM memory: nVidia Corporation nForce2 Memory Controller 2 (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:00.5 RAM memory: nVidia Corporation nForce2 Memory Controller 5 (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:01.0 ISA bridge: nVidia Corporation nForce2 ISA Bridge (rev a4)
Subsystem: Asustek Computer, Inc. A7N8X Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [48] #08 [01e1]
0000:00:01.1 SMBus: nVidia Corporation nForce2 SMBus (MCP) (rev a2)
Subsystem: Asustek Computer, Inc.: Unknown device 0c11
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at e000 [size2]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:02.0 USB Controller: nVidia Corporation nForce2 USB Controller
(rev a4) (prog-if 10 [OHCI])
Subsystem: Asustek Computer, Inc. A7N8X Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 21
Region 0: Memory at ee087000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:02.1 USB Controller: nVidia Corporation nForce2 USB Controller
(rev a4) (prog-if 10 [OHCI])
Subsystem: Asustek Computer, Inc. A7N8X Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 20
Region 0: Memory at ee082000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:02.2 USB Controller: nVidia Corporation nForce2 USB Controller
(rev a4) (prog-if 20 [EHCI])
Subsystem: Asustek Computer, Inc. A7N8X Mainboard
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin C routed to IRQ 22
Region 0: Memory at ee083000 (32-bit, non-prefetchable) [size%6]
Capabilities: [44] #0a [2080]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:04.0 Ethernet controller: nVidia Corporation nForce2 Ethernet
Controller (rev a1)
Subsystem: Asustek Computer, Inc. A7N8X Mainboard onboard
nForce2 Ethernet
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 21
Region 0: Memory at ee086000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at e400 [size=8]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:05.0 Multimedia audio controller: nVidia Corporation nForce
MultiMedia audio [Via VT82C686B] (rev a2)
Subsystem: Asustek Computer, Inc.: Unknown device 0c11
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (250ns min, 3000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at ee000000 (32-bit, non-prefetchable) [sizeQ2K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:06.0 Multimedia audio controller: nVidia Corporation nForce2
AC97 Audio Controler (MCP) (rev a1)
Subsystem: Asustek Computer, Inc.: Unknown device 8095
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at d000 [size%6]
Region 1: I/O ports at d400 [size\x128]
Region 2: Memory at ee080000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:08.0 PCI bridge: nVidia Corporation nForce2 External PCI
Bridge (rev a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary\0, secondary\x01, subordinate\x01, sec-latency2
I/O behind bridge: 0000a000-0000bfff
Memory behind bridge: ec000000-edffffff
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
0000:00:09.0 IDE interface: nVidia Corporation nForce2 IDE (rev a2)
(prog-if 8a [Master SecP PriP])
Subsystem: Asustek Computer, Inc.: Unknown device 0c11
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Region 4: I/O ports at f000 [size\x16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:0c.0 PCI bridge: nVidia Corporation nForce2 PCI Bridge (rev
a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary\0, secondary\x02, subordinate\x02, sec-latency2
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: e8000000-e9ffffff
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
0000:00:0d.0 FireWire (IEEE 1394): nVidia Corporation nForce2 FireWire
(IEEE 1394) Controller (rev a3) (prog-if 10 [OHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 809a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at ee084000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at ee085000 (32-bit, non-prefetchable) [sized]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
0000:00:1e.0 PCI bridge: nVidia Corporation nForce2 AGP (rev c1)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 16
Bus: primary\0, secondary\x03, subordinate\x03, sec-latency2
Memory behind bridge: ea000000-ebffffff
Prefetchable memory behind bridge: d0000000-dfffffff
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
0000:01:06.0 Network controller: Broadcom Corporation BCM4306
802.11b/g Wireless LAN Controller (rev 03)
Subsystem: Motorola: Unknown device 7110
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 16
Interrupt: pin A routed to IRQ 16
Region 0: Memory at ed000000 (32-bit, non-prefetchable) [size=8K]
0000:01:0b.0 RAID bus controller: Silicon Image, Inc. (formerly CMD
Technology Inc) SiI 3112 [SATALink/SATARaid] Serial ATA Controller
(rev 02)
Subsystem: Silicon Image, Inc. (formerly CMD Technology Inc) Asus A7N8X
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 16, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at a000 [size=8]
Region 1: I/O ports at a400 [size=4]
Region 2: I/O ports at a800 [size=8]
Region 3: I/O ports at ac00 [size=4]
Region 4: I/O ports at b000 [size\x16]
Region 5: Memory at ed002000 (32-bit, non-prefetchable) [sizeQ2]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
0000:02:01.0 Ethernet controller: 3Com Corporation 3C920B-EMB
Integrated Fast Ethernet Controller [Tornado] (rev 40)
Subsystem: Asustek Computer, Inc. A7N8X Deluxe onboard
3C920B-EMB Integrated Fast Ethernet Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at c000 [disabled] [size\x128]
Region 1: [virtual] Memory at e9000000 (32-bit,
non-prefetchable) [disabled] [size\x128]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D3 PME-Enable- DSel=0 DScale=2 PME-
0000:03:00.0 VGA compatible controller: nVidia Corporation NV31
[GeForce FX 5600] (rev a1) (prog-if 00 [VGA])
Subsystem: Micro-Star International Co., Ltd.: Unknown device 9123
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 19
Region 0: Memory at ea000000 (32-bit, non-prefetchable) [size\x16M]
Region 1: Memory at d0000000 (32-bit, prefetchable) [size%6M]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:00.0 Host bridge: nVidia Corporation nForce2 AGP (different
version?) (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at e0000000 (32-bit, prefetchable) [size\x128M]
Capabilities: [40] AGP version 3.0
Status: RQ2 Iso- ArqSz=2 Cal=0 SBA+ ITACoh- GART64-
HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=x4
Capabilities: [60] #08 [2001]
0000:00:00.1 RAM memory: nVidia Corporation nForce2 Memory Controller 1 (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:00.2 RAM memory: nVidia Corporation nForce2 Memory Controller 4 (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:00.3 RAM memory: nVidia Corporation nForce2 Memory Controller 3 (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:00.4 RAM memory: nVidia Corporation nForce2 Memory Controller 2 (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:00.5 RAM memory: nVidia Corporation nForce2 Memory Controller 5 (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:01.0 ISA bridge: nVidia Corporation nForce2 ISA Bridge (rev a4)
Subsystem: Asustek Computer, Inc. A7N8X Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [48] #08 [01e1]
0000:00:01.1 SMBus: nVidia Corporation nForce2 SMBus (MCP) (rev a2)
Subsystem: Asustek Computer, Inc.: Unknown device 0c11
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at e000 [size2]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:02.0 USB Controller: nVidia Corporation nForce2 USB Controller
(rev a4) (prog-if 10 [OHCI])
Subsystem: Asustek Computer, Inc. A7N8X Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 21
Region 0: Memory at ee087000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:02.1 USB Controller: nVidia Corporation nForce2 USB Controller
(rev a4) (prog-if 10 [OHCI])
Subsystem: Asustek Computer, Inc. A7N8X Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 20
Region 0: Memory at ee082000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:02.2 USB Controller: nVidia Corporation nForce2 USB Controller
(rev a4) (prog-if 20 [EHCI])
Subsystem: Asustek Computer, Inc. A7N8X Mainboard
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin C routed to IRQ 22
Region 0: Memory at ee083000 (32-bit, non-prefetchable) [size%6]
Capabilities: [44] #0a [2080]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:04.0 Ethernet controller: nVidia Corporation nForce2 Ethernet
Controller (rev a1)
Subsystem: Asustek Computer, Inc. A7N8X Mainboard onboard
nForce2 Ethernet
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 21
Region 0: Memory at ee086000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at e400 [size=8]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:05.0 Multimedia audio controller: nVidia Corporation nForce
MultiMedia audio [Via VT82C686B] (rev a2)
Subsystem: Asustek Computer, Inc.: Unknown device 0c11
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (250ns min, 3000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at ee000000 (32-bit, non-prefetchable) [sizeQ2K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:06.0 Multimedia audio controller: nVidia Corporation nForce2
AC97 Audio Controler (MCP) (rev a1)
Subsystem: Asustek Computer, Inc.: Unknown device 8095
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at d000 [size%6]
Region 1: I/O ports at d400 [size\x128]
Region 2: Memory at ee080000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:08.0 PCI bridge: nVidia Corporation nForce2 External PCI
Bridge (rev a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary\0, secondary\x01, subordinate\x01, sec-latency2
I/O behind bridge: 0000a000-0000bfff
Memory behind bridge: ec000000-edffffff
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
0000:00:09.0 IDE interface: nVidia Corporation nForce2 IDE (rev a2)
(prog-if 8a [Master SecP PriP])
Subsystem: Asustek Computer, Inc.: Unknown device 0c11
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Region 4: I/O ports at f000 [size\x16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:0c.0 PCI bridge: nVidia Corporation nForce2 PCI Bridge (rev
a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary\0, secondary\x02, subordinate\x02, sec-latency2
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: e8000000-e9ffffff
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
0000:00:0d.0 FireWire (IEEE 1394): nVidia Corporation nForce2 FireWire
(IEEE 1394) Controller (rev a3) (prog-if 10 [OHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 809a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at ee084000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at ee085000 (32-bit, non-prefetchable) [sized]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
0000:00:1e.0 PCI bridge: nVidia Corporation nForce2 AGP (rev c1)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 16
Bus: primary\0, secondary\x03, subordinate\x03, sec-latency2
Memory behind bridge: ea000000-ebffffff
Prefetchable memory behind bridge: d0000000-dfffffff
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
0000:01:06.0 Network controller: Broadcom Corporation BCM4306
802.11b/g Wireless LAN Controller (rev 03)
Subsystem: Motorola: Unknown device 7110
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 16
Interrupt: pin A routed to IRQ 16
Region 0: Memory at ed000000 (32-bit, non-prefetchable) [size=8K]
0000:01:0b.0 RAID bus controller: Silicon Image, Inc. (formerly CMD
Technology Inc) SiI 3112 [SATALink/SATARaid] Serial ATA Controller
(rev 02)
Subsystem: Silicon Image, Inc. (formerly CMD Technology Inc) Asus A7N8X
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 16, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at a000 [size=8]
Region 1: I/O ports at a400 [size=4]
Region 2: I/O ports at a800 [size=8]
Region 3: I/O ports at ac00 [size=4]
Region 4: I/O ports at b000 [size\x16]
Region 5: Memory at ed002000 (32-bit, non-prefetchable) [sizeQ2]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
0000:02:01.0 Ethernet controller: 3Com Corporation 3C920B-EMB
Integrated Fast Ethernet Controller [Tornado] (rev 40)
Subsystem: Asustek Computer, Inc. A7N8X Deluxe onboard
3C920B-EMB Integrated Fast Ethernet Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at c000 [disabled] [size\x128]
Region 1: [virtual] Memory at e9000000 (32-bit,
non-prefetchable) [disabled] [size\x128]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D3 PME-Enable- DSel=0 DScale=2 PME-
0000:03:00.0 VGA compatible controller: nVidia Corporation NV31
[GeForce FX 5600] (rev a1) (prog-if 00 [VGA])
Subsystem: Micro-Star International Co., Ltd.: Unknown device 9123
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 19
Region 0: Memory at ea000000 (32-bit, non-prefetchable) [size\x16M]
Region 1: Memory at d0000000 (32-bit, prefetchable) [size%6M]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:00.0 Host bridge: nVidia Corporation nForce2 AGP (different
version?) (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at e0000000 (32-bit, prefetchable) [size\x128M]
Capabilities: [40] AGP version 3.0
Status: RQ2 Iso- ArqSz=2 Cal=0 SBA+ ITACoh- GART64-
HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=x4
Capabilities: [60] #08 [2001]
0000:00:00.1 RAM memory: nVidia Corporation nForce2 Memory Controller 1 (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:00.2 RAM memory: nVidia Corporation nForce2 Memory Controller 4 (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:00.3 RAM memory: nVidia Corporation nForce2 Memory Controller 3 (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:00.4 RAM memory: nVidia Corporation nForce2 Memory Controller 2 (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:00.5 RAM memory: nVidia Corporation nForce2 Memory Controller 5 (rev c1)
Subsystem: Asustek Computer, Inc.: Unknown device 80ac
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
0000:00:01.0 ISA bridge: nVidia Corporation nForce2 ISA Bridge (rev a4)
Subsystem: Asustek Computer, Inc. A7N8X Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [48] #08 [01e1]
0000:00:01.1 SMBus: nVidia Corporation nForce2 SMBus (MCP) (rev a2)
Subsystem: Asustek Computer, Inc.: Unknown device 0c11
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at e000 [size2]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:02.0 USB Controller: nVidia Corporation nForce2 USB Controller
(rev a4) (prog-if 10 [OHCI])
Subsystem: Asustek Computer, Inc. A7N8X Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 21
Region 0: Memory at ee087000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:02.1 USB Controller: nVidia Corporation nForce2 USB Controller
(rev a4) (prog-if 10 [OHCI])
Subsystem: Asustek Computer, Inc. A7N8X Mainboard
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 20
Region 0: Memory at ee082000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:02.2 USB Controller: nVidia Corporation nForce2 USB Controller
(rev a4) (prog-if 20 [EHCI])
Subsystem: Asustek Computer, Inc. A7N8X Mainboard
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin C routed to IRQ 22
Region 0: Memory at ee083000 (32-bit, non-prefetchable) [size%6]
Capabilities: [44] #0a [2080]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:04.0 Ethernet controller: nVidia Corporation nForce2 Ethernet
Controller (rev a1)
Subsystem: Asustek Computer, Inc. A7N8X Mainboard onboard
nForce2 Ethernet
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 21
Region 0: Memory at ee086000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at e400 [size=8]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:05.0 Multimedia audio controller: nVidia Corporation nForce
MultiMedia audio [Via VT82C686B] (rev a2)
Subsystem: Asustek Computer, Inc.: Unknown device 0c11
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (250ns min, 3000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at ee000000 (32-bit, non-prefetchable) [sizeQ2K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:06.0 Multimedia audio controller: nVidia Corporation nForce2
AC97 Audio Controler (MCP) (rev a1)
Subsystem: Asustek Computer, Inc.: Unknown device 8095
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at d000 [size%6]
Region 1: I/O ports at d400 [size\x128]
Region 2: Memory at ee080000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:08.0 PCI bridge: nVidia Corporation nForce2 External PCI
Bridge (rev a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary\0, secondary\x01, subordinate\x01, sec-latency2
I/O behind bridge: 0000a000-0000bfff
Memory behind bridge: ec000000-edffffff
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
0000:00:09.0 IDE interface: nVidia Corporation nForce2 IDE (rev a2)
(prog-if 8a [Master SecP PriP])
Subsystem: Asustek Computer, Inc.: Unknown device 0c11
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Region 4: I/O ports at f000 [size\x16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:0c.0 PCI bridge: nVidia Corporation nForce2 PCI Bridge (rev
a3) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary\0, secondary\x02, subordinate\x02, sec-latency2
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: e8000000-e9ffffff
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
0000:00:0d.0 FireWire (IEEE 1394): nVidia Corporation nForce2 FireWire
(IEEE 1394) Controller (rev a3) (prog-if 10 [OHCI])
Subsystem: Asustek Computer, Inc.: Unknown device 809a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at ee084000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at ee085000 (32-bit, non-prefetchable) [sized]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME+
0000:00:1e.0 PCI bridge: nVidia Corporation nForce2 AGP (rev c1)
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 16
Bus: primary\0, secondary\x03, subordinate\x03, sec-latency2
Memory behind bridge: ea000000-ebffffff
Prefetchable memory behind bridge: d0000000-dfffffff
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
0000:01:06.0 Network controller: Broadcom Corporation BCM4306
802.11b/g Wireless LAN Controller (rev 03)
Subsystem: Motorola: Unknown device 7110
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSELúst >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 16
Interrupt: pin A routed to IRQ 16
Region 0: Memory at ed000000 (32-bit, non-prefetchable) [size=8K]
0000:01:0b.0 RAID bus controller: Silicon Image, Inc. (formerly CMD
Technology Inc) SiI 3112 [SATALink/SATARaid] Serial ATA Controller
(rev 02)
Subsystem: Silicon Image, Inc. (formerly CMD Technology Inc) Asus A7N8X
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 16, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 18
Region 0: I/O ports at a000 [size=8]
Region 1: I/O ports at a400 [size=4]
Region 2: I/O ports at a800 [size=8]
Region 3: I/O ports at ac00 [size=4]
Region 4: I/O ports at b000 [size\x16]
Region 5: Memory at ed002000 (32-bit, non-prefetchable) [sizeQ2]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
0000:02:01.0 Ethernet controller: 3Com Corporation 3C920B-EMB
Integrated Fast Ethernet Controller [Tornado] (rev 40)
Subsystem: Asustek Computer, Inc. A7N8X Deluxe onboard
3C920B-EMB Integrated Fast Ethernet Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 20
Region 0: I/O ports at c000 [disabled] [size\x128]
Region 1: [virtual] Memory at e9000000 (32-bit,
non-prefetchable) [disabled] [size\x128]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D3 PME-Enable- DSel=0 DScale=2 PME-
0000:03:00.0 VGA compatible controller: nVidia Corporation NV31
[GeForce FX 5600] (rev a1) (prog-if 00 [VGA])
Subsystem: Micro-Star International Co., Ltd.: Unknown device 9123
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 19
Region 0: Memory at ea000000 (32-bit, non-prefetchable) [size\x16M]
Region 1: Memory at d0000000 (32-bit, prefetchable) [size%6M]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 3.0
Status: RQ2 Iso- ArqSz=0 Cal=3 SBA+ ITACoh- GART64-
HTrans- 64bit- FW+ AGP3+ Rate=x4,x8
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit-
FW- Rate=<none>
next prev parent reply other threads:[~2005-05-19 6:25 UTC|newest]
Thread overview: 46+ messages / expand[flat|nested] mbox.gz Atom feed top
2005-05-19 6:25 Who should I write to about this OOPS in 2,6,11-mm3? Greg KH
2005-05-19 6:25 ` Antonino A. Daplas
2005-05-19 6:25 ` Jean Delvare
2005-05-19 6:25 ` Antonino A. Daplas
[not found] ` <20050317154226.24c1f8f8.akpm@osdl.org>
[not found] ` <200503180754.21258.adaplas@hotpop.com>
2005-03-22 2:40 ` Andrew Morton
2005-03-22 2:59 ` Miles Lane
2005-05-19 6:25 ` Miles Lane
2005-05-19 6:25 ` Antonino A. Daplas
2005-05-19 6:25 ` Jean Delvare
2005-05-19 6:25 ` Miles Lane
2005-05-19 6:25 ` Antonino A. Daplas
2005-05-19 6:25 ` Jean Delvare
2005-05-19 6:25 ` Miles Lane
2005-05-19 6:25 ` Antonino A. Daplas
2005-05-19 6:25 ` Jean Delvare
2005-05-19 6:25 ` Jean Delvare
2005-05-19 6:25 ` Miles Lane
2005-05-19 6:25 ` Antonino A. Daplas
2005-05-19 6:25 ` Jean Delvare
2005-05-19 6:25 ` Miles Lane
2005-05-19 6:25 ` Miles Lane
2005-05-19 6:25 ` Jean Delvare
2005-05-19 6:25 ` Miles Lane
2005-05-19 6:25 ` Miles Lane
2005-05-19 6:25 ` Andrew Morton
2005-05-19 6:25 ` Miles Lane [this message]
2005-05-19 6:25 ` Miles Lane
2005-05-19 6:25 ` Miles Lane
2005-05-19 6:25 ` Jean Delvare
2005-05-19 6:25 ` Miles Lane
2005-05-19 6:25 ` Miles Lane
2005-05-19 6:25 ` Jean Delvare
2005-05-19 6:25 ` Andrew Morton
2005-05-19 6:25 ` Miles Lane
2005-05-19 6:25 ` Andrew Morton
2005-05-19 6:25 ` Andrew Morton
2005-05-19 6:25 ` Andrew Morton
2005-05-19 6:25 ` Miles Lane
2005-05-19 6:25 ` Andrew Morton
2005-05-19 6:25 ` Miles Lane
2005-05-19 6:25 ` Jean Delvare
2005-05-19 6:25 ` Greg KH
2005-05-26 9:05 ` [lm-sensors] Re: Who should I write to about this OOPS in 2, 6, Andrew Morton
2005-05-26 9:05 ` Greg KH
2005-05-26 9:05 ` Andrew Morton
2005-05-26 9:05 ` Miles Lane
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=a44ae5cd05032309522218e97e@mail.gmail.com \
--to=miles.lane@gmail.com \
--cc=lm-sensors@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.