From: Vinod Koul <vkoul@kernel.org>
To: Shawn Lin <shawn.lin@rock-chips.com>
Cc: linux-rockchip@lists.infradead.org,
linux-phy@lists.infradead.org, Heiko Stuebner <heiko@sntech.de>,
Neil Armstrong <neil.armstrong@linaro.org>
Subject: Re: [PATCH v3] phy: rockchip: naneng-combphy: Consolidate SSC configuration
Date: Sun, 10 May 2026 16:31:39 +0530 [thread overview]
Message-ID: <agBlk6-vV3o2mPkf@vaman> (raw)
In-Reply-To: <1777251433-110466-1-git-send-email-shawn.lin@rock-chips.com>
On 27-04-26, 08:57, Shawn Lin wrote:
> The PCIe SSC configuration for the RK3588 and RK3576 SoCs required
> additional tuning which is missing. When adding these same SSC
> configurations for both of these two SoCs, as well as upcoming
> platforms, it's obvious the SSC setup code was largely duplicated
> across the platform-specific configuration functions. This becomes
> harder to maintain as more platforms are added.
>
> So extract the common SSC logic into a shared helper function,
> rk_combphy_common_cfg_ssc(). This cleans up the per-platform drivers
> and centralizes the standard configuration as possible.
Please check
https://sashiko.dev/#/patchset/1777251433-110466-1-git-send-email-shawn.lin%40rock-chips.com
>
> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
> Reviewed-by: Heiko Stuebner <heiko@sntech.de>
> Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
> ---
> .../rockchip/phy-rockchip-naneng-combphy.c | 173 ++++++++----------
> 1 file changed, 73 insertions(+), 100 deletions(-)
>
> diff --git a/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c b/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
> index b60d6bf3f33c..2b0f152f5470 100644
> --- a/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
> +++ b/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
> @@ -121,6 +121,7 @@
> #define RK3568_PHYREG32_SSC_OFFSET_500PPM 1
>
> #define RK3568_PHYREG33 0x80
> +#define RK3568_PHYREG33_PLL_SSC_CTRL BIT(5)
> #define RK3568_PHYREG33_PLL_KVCO_MASK GENMASK(4, 2)
> #define RK3568_PHYREG33_PLL_KVCO_SHIFT 2
> #define RK3568_PHYREG33_PLL_KVCO_VALUE 2
> @@ -446,6 +447,74 @@ static int rockchip_combphy_probe(struct platform_device *pdev)
> return PTR_ERR_OR_ZERO(phy_provider);
> }
>
> +static void rk_combphy_common_cfg_ssc(struct rockchip_combphy_priv *priv, unsigned long rate)
> +{
> + struct device_node *np = priv->dev->of_node;
> + u32 val;
> +
> + if (!priv->enable_ssc)
> + return;
> +
> + /* Set SSC downward spread spectrum for PCIe and USB3 */
> + if (priv->type == PHY_TYPE_PCIE || priv->type == PHY_TYPE_USB3) {
> + val = FIELD_PREP(RK3568_PHYREG32_SSC_MASK, RK3568_PHYREG32_SSC_DOWNWARD);
> + rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val, RK3568_PHYREG32);
> + }
> +
> + /* Set SSC downward spread spectrum +500ppm for SATA in 100MHz */
> + if (priv->type == PHY_TYPE_SATA && rate == REF_CLOCK_100MHz) {
> + val = FIELD_PREP(RK3568_PHYREG32_SSC_DIR_MASK,
> + RK3568_PHYREG32_SSC_DOWNWARD);
> + val |= FIELD_PREP(RK3568_PHYREG32_SSC_OFFSET_MASK,
> + RK3568_PHYREG32_SSC_OFFSET_500PPM);
> + rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val,
> + RK3568_PHYREG32);
> + }
> +
> + /* Enable SSC */
> + val = readl(priv->mmio + RK3568_PHYREG8);
> + val |= RK3568_PHYREG8_SSC_EN;
> + writel(val, priv->mmio + RK3568_PHYREG8);
> +
> + /* Some SoCs need tuning PCIe SSC instead of default configuration in 24MHz */
> + if (!of_device_is_compatible(np, "rockchip,rk3588-naneng-combphy") &&
> + !of_device_is_compatible(np, "rockchip,rk3576-naneng-combphy"))
> + return;
> +
> + /* PLL control SSC module period should be set if need tuning */
> + val = readl(priv->mmio + RK3568_PHYREG33);
> + val |= RK3568_PHYREG33_PLL_SSC_CTRL;
> + writel(val, priv->mmio + RK3568_PHYREG33);
> +
> + if (priv->type == PHY_TYPE_PCIE && rate == REF_CLOCK_24MHz) {
> + /* Set PLL loop divider */
> + writel(0x00, priv->mmio + RK3576_PHYREG17);
> + writel(RK3568_PHYREG18_PLL_LOOP, priv->mmio + RK3568_PHYREG18);
> +
> + /* Set up rx_pck invert and rx msb to disable */
> + writel(0x00, priv->mmio + RK3588_PHYREG27);
> +
> + /*
> + * Set up SU adjust signal:
> + * su_trim[7:0], PLL KVCO adjust bits[2:0] to min
> + * su_trim[15:8], PLL LPF R1 adujst bits[9:7]=3'b101
> + * su_trim[23:16], CKRCV adjust
> + * su_trim[31:24], CKDRV adjust
> + */
> + writel(0x90, priv->mmio + RK3568_PHYREG11);
> + writel(0x02, priv->mmio + RK3568_PHYREG12);
> + writel(0x08, priv->mmio + RK3568_PHYREG13);
> + writel(0x57, priv->mmio + RK3568_PHYREG14);
> + writel(0x40, priv->mmio + RK3568_PHYREG15);
> +
> + writel(RK3568_PHYREG16_SSC_CNT_VALUE, priv->mmio + RK3568_PHYREG16);
> +
> + val = FIELD_PREP(RK3568_PHYREG33_PLL_KVCO_MASK,
> + RK3576_PHYREG33_PLL_KVCO_VALUE);
> + writel(val, priv->mmio + RK3568_PHYREG33);
> + }
> +}
> +
> static int rk3528_combphy_cfg(struct rockchip_combphy_priv *priv)
> {
> const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg;
> @@ -600,21 +669,12 @@ static int rk3562_combphy_cfg(struct rockchip_combphy_priv *priv)
>
> switch (priv->type) {
> case PHY_TYPE_PCIE:
> - /* Set SSC downward spread spectrum */
> - val = RK3568_PHYREG32_SSC_DOWNWARD << RK3568_PHYREG32_SSC_DIR_SHIFT;
> - rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val, RK3568_PHYREG32);
> -
> rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_pcie, true);
> rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_pcie, true);
> rockchip_combphy_param_write(priv->phy_grf, &cfg->con2_for_pcie, true);
> rockchip_combphy_param_write(priv->phy_grf, &cfg->con3_for_pcie, true);
> break;
> case PHY_TYPE_USB3:
> - /* Set SSC downward spread spectrum */
> - val = RK3568_PHYREG32_SSC_DOWNWARD << RK3568_PHYREG32_SSC_DIR_SHIFT;
> - rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val,
> - RK3568_PHYREG32);
> -
> /* Enable adaptive CTLE for USB3.0 Rx */
> rockchip_combphy_updatel(priv, RK3568_PHYREG15_CTLE_EN,
> RK3568_PHYREG15_CTLE_EN, RK3568_PHYREG15);
> @@ -706,11 +766,7 @@ static int rk3562_combphy_cfg(struct rockchip_combphy_priv *priv)
> }
> }
>
> - if (priv->enable_ssc) {
> - val = readl(priv->mmio + RK3568_PHYREG8);
> - val |= RK3568_PHYREG8_SSC_EN;
> - writel(val, priv->mmio + RK3568_PHYREG8);
> - }
> + rk_combphy_common_cfg_ssc(priv, rate);
>
> return 0;
> }
> @@ -755,11 +811,6 @@ static int rk3568_combphy_cfg(struct rockchip_combphy_priv *priv)
>
> switch (priv->type) {
> case PHY_TYPE_PCIE:
> - /* Set SSC downward spread spectrum. */
> - val = RK3568_PHYREG32_SSC_DOWNWARD << RK3568_PHYREG32_SSC_DIR_SHIFT;
> -
> - rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val, RK3568_PHYREG32);
> -
> rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_pcie, true);
> rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_pcie, true);
> rockchip_combphy_param_write(priv->phy_grf, &cfg->con2_for_pcie, true);
> @@ -767,10 +818,6 @@ static int rk3568_combphy_cfg(struct rockchip_combphy_priv *priv)
> break;
>
> case PHY_TYPE_USB3:
> - /* Set SSC downward spread spectrum. */
> - val = RK3568_PHYREG32_SSC_DOWNWARD << RK3568_PHYREG32_SSC_DIR_SHIFT,
> - rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val, RK3568_PHYREG32);
> -
> /* Enable adaptive CTLE for USB3.0 Rx. */
> val = readl(priv->mmio + RK3568_PHYREG15);
> val |= RK3568_PHYREG15_CTLE_EN;
> @@ -880,13 +927,6 @@ static int rk3568_combphy_cfg(struct rockchip_combphy_priv *priv)
>
> writel(RK3568_PHYREG18_PLL_LOOP, priv->mmio + RK3568_PHYREG18);
> writel(RK3568_PHYREG11_SU_TRIM_0_7, priv->mmio + RK3568_PHYREG11);
> - } else if (priv->type == PHY_TYPE_SATA) {
> - /* downward spread spectrum +500ppm */
> - val = RK3568_PHYREG32_SSC_DOWNWARD << RK3568_PHYREG32_SSC_DIR_SHIFT;
> - val |= RK3568_PHYREG32_SSC_OFFSET_500PPM <<
> - RK3568_PHYREG32_SSC_OFFSET_SHIFT;
> - rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val,
> - RK3568_PHYREG32);
> }
> break;
>
> @@ -909,11 +949,7 @@ static int rk3568_combphy_cfg(struct rockchip_combphy_priv *priv)
> }
> }
>
> - if (priv->enable_ssc) {
> - val = readl(priv->mmio + RK3568_PHYREG8);
> - val |= RK3568_PHYREG8_SSC_EN;
> - writel(val, priv->mmio + RK3568_PHYREG8);
> - }
> + rk_combphy_common_cfg_ssc(priv, rate);
>
> return 0;
> }
> @@ -972,10 +1008,6 @@ static int rk3576_combphy_cfg(struct rockchip_combphy_priv *priv)
>
> switch (priv->type) {
> case PHY_TYPE_PCIE:
> - /* Set SSC downward spread spectrum */
> - val = FIELD_PREP(RK3568_PHYREG32_SSC_MASK, RK3568_PHYREG32_SSC_DOWNWARD);
> - rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val, RK3568_PHYREG32);
> -
> rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_pcie, true);
> rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_pcie, true);
> rockchip_combphy_param_write(priv->phy_grf, &cfg->con2_for_pcie, true);
> @@ -983,10 +1015,6 @@ static int rk3576_combphy_cfg(struct rockchip_combphy_priv *priv)
> break;
>
> case PHY_TYPE_USB3:
> - /* Set SSC downward spread spectrum */
> - val = FIELD_PREP(RK3568_PHYREG32_SSC_MASK, RK3568_PHYREG32_SSC_DOWNWARD);
> - rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val, RK3568_PHYREG32);
> -
> /* Enable adaptive CTLE for USB3.0 Rx */
> val = readl(priv->mmio + RK3568_PHYREG15);
> val |= RK3568_PHYREG15_CTLE_EN;
> @@ -1110,14 +1138,6 @@ static int rk3576_combphy_cfg(struct rockchip_combphy_priv *priv)
> writel(0x88, priv->mmio + RK3568_PHYREG13);
> writel(0x56, priv->mmio + RK3568_PHYREG14);
> } else if (priv->type == PHY_TYPE_SATA) {
> - /* downward spread spectrum +500ppm */
> - val = FIELD_PREP(RK3568_PHYREG32_SSC_DIR_MASK,
> - RK3568_PHYREG32_SSC_DOWNWARD);
> - val |= FIELD_PREP(RK3568_PHYREG32_SSC_OFFSET_MASK,
> - RK3568_PHYREG32_SSC_OFFSET_500PPM);
> - rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val,
> - RK3568_PHYREG32);
> -
> /* ssc ppm adjust to 3500ppm */
> rockchip_combphy_updatel(priv, RK3576_PHYREG10_SSC_PCM_MASK,
> RK3576_PHYREG10_SSC_PCM_3500PPM,
> @@ -1156,39 +1176,7 @@ static int rk3576_combphy_cfg(struct rockchip_combphy_priv *priv)
> }
> }
>
> - if (priv->enable_ssc) {
> - val = readl(priv->mmio + RK3568_PHYREG8);
> - val |= RK3568_PHYREG8_SSC_EN;
> - writel(val, priv->mmio + RK3568_PHYREG8);
> -
> - if (priv->type == PHY_TYPE_PCIE && rate == REF_CLOCK_24MHz) {
> - /* Set PLL loop divider */
> - writel(0x00, priv->mmio + RK3576_PHYREG17);
> - writel(RK3568_PHYREG18_PLL_LOOP, priv->mmio + RK3568_PHYREG18);
> -
> - /* Set up rx_pck invert and rx msb to disable */
> - writel(0x00, priv->mmio + RK3588_PHYREG27);
> -
> - /*
> - * Set up SU adjust signal:
> - * su_trim[7:0], PLL KVCO adjust bits[2:0] to min
> - * su_trim[15:8], PLL LPF R1 adujst bits[9:7]=3'b101
> - * su_trim[23:16], CKRCV adjust
> - * su_trim[31:24], CKDRV adjust
> - */
> - writel(0x90, priv->mmio + RK3568_PHYREG11);
> - writel(0x02, priv->mmio + RK3568_PHYREG12);
> - writel(0x08, priv->mmio + RK3568_PHYREG13);
> - writel(0x57, priv->mmio + RK3568_PHYREG14);
> - writel(0x40, priv->mmio + RK3568_PHYREG15);
> -
> - writel(RK3568_PHYREG16_SSC_CNT_VALUE, priv->mmio + RK3568_PHYREG16);
> -
> - val = FIELD_PREP(RK3568_PHYREG33_PLL_KVCO_MASK,
> - RK3576_PHYREG33_PLL_KVCO_VALUE);
> - writel(val, priv->mmio + RK3568_PHYREG33);
> - }
> - }
> + rk_combphy_common_cfg_ssc(priv, rate);
>
> return 0;
> }
> @@ -1255,10 +1243,6 @@ static int rk3588_combphy_cfg(struct rockchip_combphy_priv *priv)
> }
> break;
> case PHY_TYPE_USB3:
> - /* Set SSC downward spread spectrum */
> - val = RK3568_PHYREG32_SSC_DOWNWARD << RK3568_PHYREG32_SSC_DIR_SHIFT;
> - rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val, RK3568_PHYREG32);
> -
> /* Enable adaptive CTLE for USB3.0 Rx. */
> val = readl(priv->mmio + RK3568_PHYREG15);
> val |= RK3568_PHYREG15_CTLE_EN;
> @@ -1343,13 +1327,6 @@ static int rk3588_combphy_cfg(struct rockchip_combphy_priv *priv)
>
> /* Set up su_trim: */
> writel(RK3568_PHYREG11_SU_TRIM_0_7, priv->mmio + RK3568_PHYREG11);
> - } else if (priv->type == PHY_TYPE_SATA) {
> - /* downward spread spectrum +500ppm */
> - val = RK3568_PHYREG32_SSC_DOWNWARD << RK3568_PHYREG32_SSC_DIR_SHIFT;
> - val |= RK3568_PHYREG32_SSC_OFFSET_500PPM <<
> - RK3568_PHYREG32_SSC_OFFSET_SHIFT;
> - rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val,
> - RK3568_PHYREG32);
> }
> break;
> default:
> @@ -1371,11 +1348,7 @@ static int rk3588_combphy_cfg(struct rockchip_combphy_priv *priv)
> }
> }
>
> - if (priv->enable_ssc) {
> - val = readl(priv->mmio + RK3568_PHYREG8);
> - val |= RK3568_PHYREG8_SSC_EN;
> - writel(val, priv->mmio + RK3568_PHYREG8);
> - }
> + rk_combphy_common_cfg_ssc(priv, rate);
>
> return 0;
> }
> --
> 2.43.0
>
>
> --
> linux-phy mailing list
> linux-phy@lists.infradead.org
> https://lists.infradead.org/mailman/listinfo/linux-phy
--
~Vinod
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
WARNING: multiple messages have this Message-ID (diff)
From: Vinod Koul <vkoul@kernel.org>
To: Shawn Lin <shawn.lin@rock-chips.com>
Cc: linux-rockchip@lists.infradead.org,
linux-phy@lists.infradead.org, Heiko Stuebner <heiko@sntech.de>,
Neil Armstrong <neil.armstrong@linaro.org>
Subject: Re: [PATCH v3] phy: rockchip: naneng-combphy: Consolidate SSC configuration
Date: Sun, 10 May 2026 16:31:39 +0530 [thread overview]
Message-ID: <agBlk6-vV3o2mPkf@vaman> (raw)
In-Reply-To: <1777251433-110466-1-git-send-email-shawn.lin@rock-chips.com>
On 27-04-26, 08:57, Shawn Lin wrote:
> The PCIe SSC configuration for the RK3588 and RK3576 SoCs required
> additional tuning which is missing. When adding these same SSC
> configurations for both of these two SoCs, as well as upcoming
> platforms, it's obvious the SSC setup code was largely duplicated
> across the platform-specific configuration functions. This becomes
> harder to maintain as more platforms are added.
>
> So extract the common SSC logic into a shared helper function,
> rk_combphy_common_cfg_ssc(). This cleans up the per-platform drivers
> and centralizes the standard configuration as possible.
Please check
https://sashiko.dev/#/patchset/1777251433-110466-1-git-send-email-shawn.lin%40rock-chips.com
>
> Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
> Reviewed-by: Heiko Stuebner <heiko@sntech.de>
> Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
> ---
> .../rockchip/phy-rockchip-naneng-combphy.c | 173 ++++++++----------
> 1 file changed, 73 insertions(+), 100 deletions(-)
>
> diff --git a/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c b/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
> index b60d6bf3f33c..2b0f152f5470 100644
> --- a/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
> +++ b/drivers/phy/rockchip/phy-rockchip-naneng-combphy.c
> @@ -121,6 +121,7 @@
> #define RK3568_PHYREG32_SSC_OFFSET_500PPM 1
>
> #define RK3568_PHYREG33 0x80
> +#define RK3568_PHYREG33_PLL_SSC_CTRL BIT(5)
> #define RK3568_PHYREG33_PLL_KVCO_MASK GENMASK(4, 2)
> #define RK3568_PHYREG33_PLL_KVCO_SHIFT 2
> #define RK3568_PHYREG33_PLL_KVCO_VALUE 2
> @@ -446,6 +447,74 @@ static int rockchip_combphy_probe(struct platform_device *pdev)
> return PTR_ERR_OR_ZERO(phy_provider);
> }
>
> +static void rk_combphy_common_cfg_ssc(struct rockchip_combphy_priv *priv, unsigned long rate)
> +{
> + struct device_node *np = priv->dev->of_node;
> + u32 val;
> +
> + if (!priv->enable_ssc)
> + return;
> +
> + /* Set SSC downward spread spectrum for PCIe and USB3 */
> + if (priv->type == PHY_TYPE_PCIE || priv->type == PHY_TYPE_USB3) {
> + val = FIELD_PREP(RK3568_PHYREG32_SSC_MASK, RK3568_PHYREG32_SSC_DOWNWARD);
> + rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val, RK3568_PHYREG32);
> + }
> +
> + /* Set SSC downward spread spectrum +500ppm for SATA in 100MHz */
> + if (priv->type == PHY_TYPE_SATA && rate == REF_CLOCK_100MHz) {
> + val = FIELD_PREP(RK3568_PHYREG32_SSC_DIR_MASK,
> + RK3568_PHYREG32_SSC_DOWNWARD);
> + val |= FIELD_PREP(RK3568_PHYREG32_SSC_OFFSET_MASK,
> + RK3568_PHYREG32_SSC_OFFSET_500PPM);
> + rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val,
> + RK3568_PHYREG32);
> + }
> +
> + /* Enable SSC */
> + val = readl(priv->mmio + RK3568_PHYREG8);
> + val |= RK3568_PHYREG8_SSC_EN;
> + writel(val, priv->mmio + RK3568_PHYREG8);
> +
> + /* Some SoCs need tuning PCIe SSC instead of default configuration in 24MHz */
> + if (!of_device_is_compatible(np, "rockchip,rk3588-naneng-combphy") &&
> + !of_device_is_compatible(np, "rockchip,rk3576-naneng-combphy"))
> + return;
> +
> + /* PLL control SSC module period should be set if need tuning */
> + val = readl(priv->mmio + RK3568_PHYREG33);
> + val |= RK3568_PHYREG33_PLL_SSC_CTRL;
> + writel(val, priv->mmio + RK3568_PHYREG33);
> +
> + if (priv->type == PHY_TYPE_PCIE && rate == REF_CLOCK_24MHz) {
> + /* Set PLL loop divider */
> + writel(0x00, priv->mmio + RK3576_PHYREG17);
> + writel(RK3568_PHYREG18_PLL_LOOP, priv->mmio + RK3568_PHYREG18);
> +
> + /* Set up rx_pck invert and rx msb to disable */
> + writel(0x00, priv->mmio + RK3588_PHYREG27);
> +
> + /*
> + * Set up SU adjust signal:
> + * su_trim[7:0], PLL KVCO adjust bits[2:0] to min
> + * su_trim[15:8], PLL LPF R1 adujst bits[9:7]=3'b101
> + * su_trim[23:16], CKRCV adjust
> + * su_trim[31:24], CKDRV adjust
> + */
> + writel(0x90, priv->mmio + RK3568_PHYREG11);
> + writel(0x02, priv->mmio + RK3568_PHYREG12);
> + writel(0x08, priv->mmio + RK3568_PHYREG13);
> + writel(0x57, priv->mmio + RK3568_PHYREG14);
> + writel(0x40, priv->mmio + RK3568_PHYREG15);
> +
> + writel(RK3568_PHYREG16_SSC_CNT_VALUE, priv->mmio + RK3568_PHYREG16);
> +
> + val = FIELD_PREP(RK3568_PHYREG33_PLL_KVCO_MASK,
> + RK3576_PHYREG33_PLL_KVCO_VALUE);
> + writel(val, priv->mmio + RK3568_PHYREG33);
> + }
> +}
> +
> static int rk3528_combphy_cfg(struct rockchip_combphy_priv *priv)
> {
> const struct rockchip_combphy_grfcfg *cfg = priv->cfg->grfcfg;
> @@ -600,21 +669,12 @@ static int rk3562_combphy_cfg(struct rockchip_combphy_priv *priv)
>
> switch (priv->type) {
> case PHY_TYPE_PCIE:
> - /* Set SSC downward spread spectrum */
> - val = RK3568_PHYREG32_SSC_DOWNWARD << RK3568_PHYREG32_SSC_DIR_SHIFT;
> - rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val, RK3568_PHYREG32);
> -
> rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_pcie, true);
> rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_pcie, true);
> rockchip_combphy_param_write(priv->phy_grf, &cfg->con2_for_pcie, true);
> rockchip_combphy_param_write(priv->phy_grf, &cfg->con3_for_pcie, true);
> break;
> case PHY_TYPE_USB3:
> - /* Set SSC downward spread spectrum */
> - val = RK3568_PHYREG32_SSC_DOWNWARD << RK3568_PHYREG32_SSC_DIR_SHIFT;
> - rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val,
> - RK3568_PHYREG32);
> -
> /* Enable adaptive CTLE for USB3.0 Rx */
> rockchip_combphy_updatel(priv, RK3568_PHYREG15_CTLE_EN,
> RK3568_PHYREG15_CTLE_EN, RK3568_PHYREG15);
> @@ -706,11 +766,7 @@ static int rk3562_combphy_cfg(struct rockchip_combphy_priv *priv)
> }
> }
>
> - if (priv->enable_ssc) {
> - val = readl(priv->mmio + RK3568_PHYREG8);
> - val |= RK3568_PHYREG8_SSC_EN;
> - writel(val, priv->mmio + RK3568_PHYREG8);
> - }
> + rk_combphy_common_cfg_ssc(priv, rate);
>
> return 0;
> }
> @@ -755,11 +811,6 @@ static int rk3568_combphy_cfg(struct rockchip_combphy_priv *priv)
>
> switch (priv->type) {
> case PHY_TYPE_PCIE:
> - /* Set SSC downward spread spectrum. */
> - val = RK3568_PHYREG32_SSC_DOWNWARD << RK3568_PHYREG32_SSC_DIR_SHIFT;
> -
> - rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val, RK3568_PHYREG32);
> -
> rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_pcie, true);
> rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_pcie, true);
> rockchip_combphy_param_write(priv->phy_grf, &cfg->con2_for_pcie, true);
> @@ -767,10 +818,6 @@ static int rk3568_combphy_cfg(struct rockchip_combphy_priv *priv)
> break;
>
> case PHY_TYPE_USB3:
> - /* Set SSC downward spread spectrum. */
> - val = RK3568_PHYREG32_SSC_DOWNWARD << RK3568_PHYREG32_SSC_DIR_SHIFT,
> - rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val, RK3568_PHYREG32);
> -
> /* Enable adaptive CTLE for USB3.0 Rx. */
> val = readl(priv->mmio + RK3568_PHYREG15);
> val |= RK3568_PHYREG15_CTLE_EN;
> @@ -880,13 +927,6 @@ static int rk3568_combphy_cfg(struct rockchip_combphy_priv *priv)
>
> writel(RK3568_PHYREG18_PLL_LOOP, priv->mmio + RK3568_PHYREG18);
> writel(RK3568_PHYREG11_SU_TRIM_0_7, priv->mmio + RK3568_PHYREG11);
> - } else if (priv->type == PHY_TYPE_SATA) {
> - /* downward spread spectrum +500ppm */
> - val = RK3568_PHYREG32_SSC_DOWNWARD << RK3568_PHYREG32_SSC_DIR_SHIFT;
> - val |= RK3568_PHYREG32_SSC_OFFSET_500PPM <<
> - RK3568_PHYREG32_SSC_OFFSET_SHIFT;
> - rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val,
> - RK3568_PHYREG32);
> }
> break;
>
> @@ -909,11 +949,7 @@ static int rk3568_combphy_cfg(struct rockchip_combphy_priv *priv)
> }
> }
>
> - if (priv->enable_ssc) {
> - val = readl(priv->mmio + RK3568_PHYREG8);
> - val |= RK3568_PHYREG8_SSC_EN;
> - writel(val, priv->mmio + RK3568_PHYREG8);
> - }
> + rk_combphy_common_cfg_ssc(priv, rate);
>
> return 0;
> }
> @@ -972,10 +1008,6 @@ static int rk3576_combphy_cfg(struct rockchip_combphy_priv *priv)
>
> switch (priv->type) {
> case PHY_TYPE_PCIE:
> - /* Set SSC downward spread spectrum */
> - val = FIELD_PREP(RK3568_PHYREG32_SSC_MASK, RK3568_PHYREG32_SSC_DOWNWARD);
> - rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val, RK3568_PHYREG32);
> -
> rockchip_combphy_param_write(priv->phy_grf, &cfg->con0_for_pcie, true);
> rockchip_combphy_param_write(priv->phy_grf, &cfg->con1_for_pcie, true);
> rockchip_combphy_param_write(priv->phy_grf, &cfg->con2_for_pcie, true);
> @@ -983,10 +1015,6 @@ static int rk3576_combphy_cfg(struct rockchip_combphy_priv *priv)
> break;
>
> case PHY_TYPE_USB3:
> - /* Set SSC downward spread spectrum */
> - val = FIELD_PREP(RK3568_PHYREG32_SSC_MASK, RK3568_PHYREG32_SSC_DOWNWARD);
> - rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val, RK3568_PHYREG32);
> -
> /* Enable adaptive CTLE for USB3.0 Rx */
> val = readl(priv->mmio + RK3568_PHYREG15);
> val |= RK3568_PHYREG15_CTLE_EN;
> @@ -1110,14 +1138,6 @@ static int rk3576_combphy_cfg(struct rockchip_combphy_priv *priv)
> writel(0x88, priv->mmio + RK3568_PHYREG13);
> writel(0x56, priv->mmio + RK3568_PHYREG14);
> } else if (priv->type == PHY_TYPE_SATA) {
> - /* downward spread spectrum +500ppm */
> - val = FIELD_PREP(RK3568_PHYREG32_SSC_DIR_MASK,
> - RK3568_PHYREG32_SSC_DOWNWARD);
> - val |= FIELD_PREP(RK3568_PHYREG32_SSC_OFFSET_MASK,
> - RK3568_PHYREG32_SSC_OFFSET_500PPM);
> - rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val,
> - RK3568_PHYREG32);
> -
> /* ssc ppm adjust to 3500ppm */
> rockchip_combphy_updatel(priv, RK3576_PHYREG10_SSC_PCM_MASK,
> RK3576_PHYREG10_SSC_PCM_3500PPM,
> @@ -1156,39 +1176,7 @@ static int rk3576_combphy_cfg(struct rockchip_combphy_priv *priv)
> }
> }
>
> - if (priv->enable_ssc) {
> - val = readl(priv->mmio + RK3568_PHYREG8);
> - val |= RK3568_PHYREG8_SSC_EN;
> - writel(val, priv->mmio + RK3568_PHYREG8);
> -
> - if (priv->type == PHY_TYPE_PCIE && rate == REF_CLOCK_24MHz) {
> - /* Set PLL loop divider */
> - writel(0x00, priv->mmio + RK3576_PHYREG17);
> - writel(RK3568_PHYREG18_PLL_LOOP, priv->mmio + RK3568_PHYREG18);
> -
> - /* Set up rx_pck invert and rx msb to disable */
> - writel(0x00, priv->mmio + RK3588_PHYREG27);
> -
> - /*
> - * Set up SU adjust signal:
> - * su_trim[7:0], PLL KVCO adjust bits[2:0] to min
> - * su_trim[15:8], PLL LPF R1 adujst bits[9:7]=3'b101
> - * su_trim[23:16], CKRCV adjust
> - * su_trim[31:24], CKDRV adjust
> - */
> - writel(0x90, priv->mmio + RK3568_PHYREG11);
> - writel(0x02, priv->mmio + RK3568_PHYREG12);
> - writel(0x08, priv->mmio + RK3568_PHYREG13);
> - writel(0x57, priv->mmio + RK3568_PHYREG14);
> - writel(0x40, priv->mmio + RK3568_PHYREG15);
> -
> - writel(RK3568_PHYREG16_SSC_CNT_VALUE, priv->mmio + RK3568_PHYREG16);
> -
> - val = FIELD_PREP(RK3568_PHYREG33_PLL_KVCO_MASK,
> - RK3576_PHYREG33_PLL_KVCO_VALUE);
> - writel(val, priv->mmio + RK3568_PHYREG33);
> - }
> - }
> + rk_combphy_common_cfg_ssc(priv, rate);
>
> return 0;
> }
> @@ -1255,10 +1243,6 @@ static int rk3588_combphy_cfg(struct rockchip_combphy_priv *priv)
> }
> break;
> case PHY_TYPE_USB3:
> - /* Set SSC downward spread spectrum */
> - val = RK3568_PHYREG32_SSC_DOWNWARD << RK3568_PHYREG32_SSC_DIR_SHIFT;
> - rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val, RK3568_PHYREG32);
> -
> /* Enable adaptive CTLE for USB3.0 Rx. */
> val = readl(priv->mmio + RK3568_PHYREG15);
> val |= RK3568_PHYREG15_CTLE_EN;
> @@ -1343,13 +1327,6 @@ static int rk3588_combphy_cfg(struct rockchip_combphy_priv *priv)
>
> /* Set up su_trim: */
> writel(RK3568_PHYREG11_SU_TRIM_0_7, priv->mmio + RK3568_PHYREG11);
> - } else if (priv->type == PHY_TYPE_SATA) {
> - /* downward spread spectrum +500ppm */
> - val = RK3568_PHYREG32_SSC_DOWNWARD << RK3568_PHYREG32_SSC_DIR_SHIFT;
> - val |= RK3568_PHYREG32_SSC_OFFSET_500PPM <<
> - RK3568_PHYREG32_SSC_OFFSET_SHIFT;
> - rockchip_combphy_updatel(priv, RK3568_PHYREG32_SSC_MASK, val,
> - RK3568_PHYREG32);
> }
> break;
> default:
> @@ -1371,11 +1348,7 @@ static int rk3588_combphy_cfg(struct rockchip_combphy_priv *priv)
> }
> }
>
> - if (priv->enable_ssc) {
> - val = readl(priv->mmio + RK3568_PHYREG8);
> - val |= RK3568_PHYREG8_SSC_EN;
> - writel(val, priv->mmio + RK3568_PHYREG8);
> - }
> + rk_combphy_common_cfg_ssc(priv, rate);
>
> return 0;
> }
> --
> 2.43.0
>
>
> --
> linux-phy mailing list
> linux-phy@lists.infradead.org
> https://lists.infradead.org/mailman/listinfo/linux-phy
--
~Vinod
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip
next prev parent reply other threads:[~2026-05-10 11:01 UTC|newest]
Thread overview: 4+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-04-27 0:57 [PATCH v3] phy: rockchip: naneng-combphy: Consolidate SSC configuration Shawn Lin
2026-04-27 0:57 ` Shawn Lin
2026-05-10 11:01 ` Vinod Koul [this message]
2026-05-10 11:01 ` Vinod Koul
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=agBlk6-vV3o2mPkf@vaman \
--to=vkoul@kernel.org \
--cc=heiko@sntech.de \
--cc=linux-phy@lists.infradead.org \
--cc=linux-rockchip@lists.infradead.org \
--cc=neil.armstrong@linaro.org \
--cc=shawn.lin@rock-chips.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.