[PATCH v3 0/9] gpio: mxc: bug fixes and probe cleanup

[PATCH v3 0/9] gpio: mxc: bug fixes and probe cleanup

[Peng Fan (OSS)]

This series cleans up the gpio-mxc driver in several incremental steps:
bug fixes, converting runtime state to static per-compatible data,
modernizing resource management with devres, and cleaning up
register access patterns.

Patches 1-2 are bug fixes:
  - Fix a race where the chained IRQ handler is installed before probe
    completes, allowing interrupts to fire on a half-initialized port.
  - Fix wakeup_pads bit operations that used wrong set_bit/clear_bit
    logic, folding in the assign_bit() simplification from V1.

Patches 3-4 replace runtime of_device_is_compatible() calls with static
per-compatible hwdata flags, eliminating repeated string comparisons in
the suspend/resume path.

Patches 5-6 convert probe error handling to devres and dev_err_probe().

Patches 7-9 are cosmetic cleanups: local dev variable, MXC_ICR macros
with field_prep/field_get, and BIT() macro for single-bit shifts.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
Changes in v3:
- Patch 5/8 ("gpio: mxc: convert probe error handling to devres"):
  Replaced pm_runtime_get_noresume() with
  devm_pm_runtime_get_noresume() to fix a PM usage counter leak on
  probe error paths. The non-devm pm_runtime_get_noresume() was not
  balanced by any devres action, so any probe failure after the PM
  block (e.g. -EPROBE_DEFER from devm_gpiochip_add_data()) would
  leave usage_count permanently elevated, preventing runtime suspend
  on re-probe.
  Dropped the explicit pm_runtime_put_noidle() on
  devm_pm_runtime_set_active_enabled() failure - the devres
  registered by devm_pm_runtime_get_noresume() handles the balance
  automatically during probe unwind.
- Patch 6/8 ("gpio: mxc: use local dev variable"):
  Keep of_device_is_compatible(), only focus on switching &pdev->dev to
  dev.
- Link to v2: https://patch.msgid.link/20261005-gpio-mxc-cleanup-v2-0-bdc3afbb35e2@nxp.com

Changes in V2:
- Reworked compatible-string caching (V1 patch 3) from probe-time bools
  in mxc_gpio_port to static hwdata flags with per-compatible data
  instances.  Split into two patches: one introducing the flags scheme
  with MXC_GPIO_HW_DATA_COMMON macro for power_off (patch 3), one
  extending it to pad_wakeup and imx8qm (patch 4).  (Frank, bot review)
- Replaced devm_pm_runtime_get_noresume() + pm_runtime_set_active() +
  devm_pm_runtime_enable() with devm_pm_runtime_set_active_enabled().
  Keep plain pm_runtime_get_noresume() (non-devm) for the probe-scoped
  reference to avoid usage_count underflow on unbind.  (Frank, bot review)
- Replaced irq_domain_create_legacy() + devm_add_action_or_reset() with
  devm_irq_domain_instantiate().  Squashed with the PM runtime devres
  conversion (V1 patches 4+5) into a single patch (patch 5), since the
  goto labels cannot be removed until both resources are devres-managed.
- Split dev_err_probe() conversion into its own patch (patch 6) for
  bisectability — patch 5 uses bare returns with correct error values.
- Folded gpio_set_wake_irq() assign_bit simplification (V1 patch 9) into
  the wakeup_pads fix (patch 2) where it belongs.
- Used 0x3U (unsigned) in MXC_ICR_MASK() to avoid implementation-defined
  behavior when shifting by 30 bits.
- Replaced linux/of.h with linux/property.h to match the
  of_device_is_compatible() → device_is_compatible() API change (patch 7).
- Added return-value checks for devm_pm_runtime_set_active_enabled().
- Fixed stale error code returns after devm_irq_alloc_descs() and
  devm_irq_domain_instantiate() in the devres conversion patch.
- Link to v1: https://patch.msgid.link/20261003-gpio-mxc-cleanup-v1-0-dad728ce27f2@nxp.com

---
Peng Fan (9):
      gpio: mxc: fix race between chained IRQ handler install and probe completion
      gpio: mxc: fix wakeup_pads bit operations
      gpio: mxc: replace of_device_is_compatible() with hwdata flags
      gpio: mxc: convert pad wakeup compatible checks to hwdata flags
      gpio: mxc: convert probe error handling to devres
      gpio: mxc: switch probe error paths to dev_err_probe()
      gpio: mxc: use local dev variable
      gpio: mxc: introduce MXC_ICR macros and use field_prep/field_get
      gpio: mxc: use BIT() macro for single-bit operations

 drivers/gpio/gpio-mxc.c | 257 +++++++++++++++++++++++++++---------------------
 1 file changed, 145 insertions(+), 112 deletions(-)
---
base-commit: f0406245cb9855e6318335a8a223551354291a46
change-id: 20261003-gpio-mxc-cleanup-e49cc626c51e

Best regards,
--  
Peng Fan <peng.fan@nxp.com>

[PATCH v3 1/9] gpio: mxc: fix race between chained IRQ handler install and probe completion

[Peng Fan (OSS)]

From: Peng Fan <peng.fan@nxp.com>

mxc_update_irq_chained_handler() is called before the IRQ domain, the
generic IRQ chip, and the port list entry are set up. If an interrupt
arrives in that window:

 - mx3_gpio_irq_handler() calls generic_handle_domain_irq() with
   port->domain still NULL.
 - mx2_gpio_irq_handler() walks mxc_gpio_ports, but the port has not
   been added to the list yet.

Additionally, if any of the subsequent probe steps
(gpio_generic_chip_init(), devm_gpiochip_add_data(),
irq_domain_create_legacy(), or mxc_gpio_init_gc()) fail, the error
paths never unregister the chained handler, leaving a dangling handler
that points at freed memory.

Move the handler installation after all its dependencies are ready and
after list_add_tail(), so the handler is never live while the data
structures it touches are incomplete, and is never installed if probe
fails.

Fixes: 5f6d1998adeb ("gpio: mxc: release the parent IRQ in runtime suspend")
Assisted-by: LLM
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
 drivers/gpio/gpio-mxc.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/gpio/gpio-mxc.c b/drivers/gpio/gpio-mxc.c
index 7e2690d92df6..e05f276a50e8 100644
--- a/drivers/gpio/gpio-mxc.c
+++ b/drivers/gpio/gpio-mxc.c
@@ -474,8 +474,6 @@ static int mxc_gpio_probe(struct platform_device *pdev)
 	} else
 		port->mx_irq_handler = mx3_gpio_irq_handler;
 
-	mxc_update_irq_chained_handler(port, true);
-
 	config.dev = &pdev->dev;
 	config.sz = 4;
 	config.dat = port->base + GPIO_PSR;
@@ -525,6 +523,8 @@ static int mxc_gpio_probe(struct platform_device *pdev)
 
 	list_add_tail(&port->node, &mxc_gpio_ports);
 
+	mxc_update_irq_chained_handler(port, true);
+
 	platform_set_drvdata(pdev, port);
 	pm_runtime_put_autosuspend(&pdev->dev);
 

-- 
2.51.0

[PATCH v3 2/9] gpio: mxc: fix wakeup_pads bit operations

[Peng Fan (OSS)]

From: Peng Fan <peng.fan@nxp.com>

gpio_set_wake_irq() can be called concurrently for different pins on
the same port, so need to use atomic bitops when modifying wakeup_pads.

Since wakeup_pads is u32 but assign_bit() operate on unsigned long
pointers. On 64-bit platforms this causes an 8-byte read-modify-write
on a 4-byte field, corrupting the adjacent is_pad_wakeup member.
Change wakeup_pads to unsigned long and reorder to avoid the overlap.

And the enable/disable path unconditionally sets/clears the wakeup_pads
bit even when enable_irq_wake()/disable_irq_wake() fails. Only update
the bit on success.

While at here, simplify the logic by consolidating into a single
irq_set_irq_wake() call based on the enable parameter.

Fixes: f60c9eac54af ("gpio: mxc: enable pad wakeup on i.MX8x platforms")
Assisted-by: LLM
Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
 drivers/gpio/gpio-mxc.c | 52 ++++++++++++++++++++++---------------------------
 1 file changed, 23 insertions(+), 29 deletions(-)

diff --git a/drivers/gpio/gpio-mxc.c b/drivers/gpio/gpio-mxc.c
index e05f276a50e8..0013f73d23bf 100644
--- a/drivers/gpio/gpio-mxc.c
+++ b/drivers/gpio/gpio-mxc.c
@@ -71,8 +71,8 @@ struct mxc_gpio_port {
 	u32 both_edges;
 	struct mxc_gpio_reg_saved gpio_saved_reg;
 	bool power_off;
-	u32 wakeup_pads;
 	bool is_pad_wakeup;
+	unsigned long wakeup_pads;
 	u32 pad_type[32];
 	const struct mxc_gpio_hwdata *hwdata;
 };
@@ -325,21 +325,17 @@ static int gpio_set_wake_irq(struct irq_data *d, u32 enable)
 	u32 gpio_idx = d->hwirq;
 	int ret;
 
-	if (enable) {
-		if (port->irq_high && (gpio_idx >= 16))
-			ret = enable_irq_wake(port->irq_high);
-		else
-			ret = enable_irq_wake(port->irq);
-		port->wakeup_pads |= BIT(gpio_idx);
-	} else {
-		if (port->irq_high && (gpio_idx >= 16))
-			ret = disable_irq_wake(port->irq_high);
-		else
-			ret = disable_irq_wake(port->irq);
-		port->wakeup_pads &= ~BIT(gpio_idx);
-	}
+	if (port->irq_high && (gpio_idx >= 16))
+		ret = irq_set_irq_wake(port->irq_high, enable);
+	else
+		ret = irq_set_irq_wake(port->irq, enable);
 
-	return ret;
+	if (ret)
+		return ret;
+
+	assign_bit(gpio_idx, &port->wakeup_pads, enable);
+
+	return 0;
 }
 
 static int mxc_gpio_init_gc(struct mxc_gpio_port *port, int irq_base)
@@ -598,22 +594,20 @@ static bool mxc_gpio_set_pad_wakeup(struct mxc_gpio_port *port, bool enable)
 		IMX_SCU_WAKEUP_LOW_LVL,		/* IRQ_TYPE_LEVEL_LOW */
 	};
 
-	for (i = 0; i < 32; i++) {
-		if ((port->wakeup_pads & (1 << i))) {
-			type = port->pad_type[i];
-			if (enable)
-				config = pad_type_map[type];
-			else
-				config = IMX_SCU_WAKEUP_OFF;
-
-			if (is_imx8qm && config == IMX_SCU_WAKEUP_FALL_EDGE) {
-				dev_warn_once(port->dev,
-					      "No falling-edge support for wakeup on i.MX8QM\n");
-				config = IMX_SCU_WAKEUP_OFF;
-			}
+	for_each_set_bit(i, &port->wakeup_pads, 32) {
+		type = port->pad_type[i];
+		if (enable)
+			config = pad_type_map[type];
+		else
+			config = IMX_SCU_WAKEUP_OFF;
 
-			ret |= mxc_gpio_generic_config(port, i, config);
+		if (is_imx8qm && config == IMX_SCU_WAKEUP_FALL_EDGE) {
+			dev_warn_once(port->dev,
+				      "No falling-edge support for wakeup on i.MX8QM\n");
+			config = IMX_SCU_WAKEUP_OFF;
 		}
+
+		ret |= mxc_gpio_generic_config(port, i, config);
 	}
 
 	return ret;

-- 
2.51.0

[PATCH v3 3/9] gpio: mxc: replace of_device_is_compatible() with hwdata flags

[Peng Fan (OSS)]

From: Peng Fan <peng.fan@nxp.com>

Replace the runtime of_device_is_compatible() check for "fsl,imx7d-gpio"
with a flags field in mxc_gpio_hwdata to move the power-off capability
from a per-instance bool populated at probe time to static per-compatible
data.

Introduce MXC_GPIO_HAS_POWER_OFF and a dedicated imx7d_gpio_hwdata
instance that carries it, along with a mxc_gpio_has_power_off() helper
that replaces every former port->power_off test.

While at it, factor the register offsets shared by imx35 and imx7d into
a MXC_GPIO_HW_DATA_COMMON macro to avoid duplicating twelve identical
initializers.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
 drivers/gpio/gpio-mxc.c | 50 ++++++++++++++++++++++++++++++-------------------
 1 file changed, 31 insertions(+), 19 deletions(-)

diff --git a/drivers/gpio/gpio-mxc.c b/drivers/gpio/gpio-mxc.c
index 0013f73d23bf..5fbbfcebaa8f 100644
--- a/drivers/gpio/gpio-mxc.c
+++ b/drivers/gpio/gpio-mxc.c
@@ -33,6 +33,8 @@
 #define IMX_SCU_WAKEUP_RISE_EDGE	6
 #define IMX_SCU_WAKEUP_HIGH_LVL		7
 
+#define MXC_GPIO_HAS_POWER_OFF		BIT(0)
+
 /* device type dependent stuff */
 struct mxc_gpio_hwdata {
 	unsigned dr_reg;
@@ -47,6 +49,7 @@ struct mxc_gpio_hwdata {
 	unsigned high_level;
 	unsigned rise_edge;
 	unsigned fall_edge;
+	unsigned int flags;
 };
 
 struct mxc_gpio_reg_saved {
@@ -70,13 +73,26 @@ struct mxc_gpio_port {
 	struct device *dev;
 	u32 both_edges;
 	struct mxc_gpio_reg_saved gpio_saved_reg;
-	bool power_off;
 	bool is_pad_wakeup;
 	unsigned long wakeup_pads;
 	u32 pad_type[32];
 	const struct mxc_gpio_hwdata *hwdata;
 };
 
+#define MXC_GPIO_HW_DATA_COMMON	\
+	.dr_reg		= 0x00,	\
+	.gdir_reg	= 0x04,	\
+	.psr_reg	= 0x08,	\
+	.icr1_reg	= 0x0c,	\
+	.icr2_reg	= 0x10,	\
+	.imr_reg	= 0x14,	\
+	.isr_reg	= 0x18,	\
+	.edge_sel_reg	= 0x1c,	\
+	.low_level	= 0x00,	\
+	.high_level	= 0x01,	\
+	.rise_edge	= 0x02,	\
+	.fall_edge	= 0x03
+
 static struct mxc_gpio_hwdata imx1_imx21_gpio_hwdata = {
 	.dr_reg		= 0x1c,
 	.gdir_reg	= 0x00,
@@ -108,20 +124,19 @@ static struct mxc_gpio_hwdata imx31_gpio_hwdata = {
 };
 
 static struct mxc_gpio_hwdata imx35_gpio_hwdata = {
-	.dr_reg		= 0x00,
-	.gdir_reg	= 0x04,
-	.psr_reg	= 0x08,
-	.icr1_reg	= 0x0c,
-	.icr2_reg	= 0x10,
-	.imr_reg	= 0x14,
-	.isr_reg	= 0x18,
-	.edge_sel_reg	= 0x1c,
-	.low_level	= 0x00,
-	.high_level	= 0x01,
-	.rise_edge	= 0x02,
-	.fall_edge	= 0x03,
+	MXC_GPIO_HW_DATA_COMMON,
+};
+
+static struct mxc_gpio_hwdata imx7d_gpio_hwdata = {
+	MXC_GPIO_HW_DATA_COMMON,
+	.flags = MXC_GPIO_HAS_POWER_OFF,
 };
 
+static inline bool mxc_gpio_has_power_off(struct mxc_gpio_port *port)
+{
+	return port->hwdata->flags & MXC_GPIO_HAS_POWER_OFF;
+}
+
 #define GPIO_DR			(port->hwdata->dr_reg)
 #define GPIO_GDIR		(port->hwdata->gdir_reg)
 #define GPIO_PSR		(port->hwdata->psr_reg)
@@ -142,7 +157,7 @@ static const struct of_device_id mxc_gpio_dt_ids[] = {
 	{ .compatible = "fsl,imx21-gpio", .data = &imx1_imx21_gpio_hwdata },
 	{ .compatible = "fsl,imx31-gpio", .data = &imx31_gpio_hwdata },
 	{ .compatible = "fsl,imx35-gpio", .data = &imx35_gpio_hwdata },
-	{ .compatible = "fsl,imx7d-gpio", .data = &imx35_gpio_hwdata },
+	{ .compatible = "fsl,imx7d-gpio", .data = &imx7d_gpio_hwdata },
 	{ .compatible = "fsl,imx8dxl-gpio", .data = &imx35_gpio_hwdata },
 	{ .compatible = "fsl,imx8qm-gpio", .data = &imx35_gpio_hwdata },
 	{ .compatible = "fsl,imx8qxp-gpio", .data = &imx35_gpio_hwdata },
@@ -448,9 +463,6 @@ static int mxc_gpio_probe(struct platform_device *pdev)
 	if (IS_ERR(port->clk))
 		return PTR_ERR(port->clk);
 
-	if (of_device_is_compatible(np, "fsl,imx7d-gpio"))
-		port->power_off = true;
-
 	pm_runtime_get_noresume(&pdev->dev);
 	pm_runtime_set_active(&pdev->dev);
 	pm_runtime_enable(&pdev->dev);
@@ -537,7 +549,7 @@ static int mxc_gpio_probe(struct platform_device *pdev)
 
 static void mxc_gpio_save_regs(struct mxc_gpio_port *port)
 {
-	if (!port->power_off)
+	if (!mxc_gpio_has_power_off(port))
 		return;
 
 	port->gpio_saved_reg.icr1 = readl(port->base + GPIO_ICR1);
@@ -550,7 +562,7 @@ static void mxc_gpio_save_regs(struct mxc_gpio_port *port)
 
 static void mxc_gpio_restore_regs(struct mxc_gpio_port *port)
 {
-	if (!port->power_off)
+	if (!mxc_gpio_has_power_off(port))
 		return;
 
 	writel(port->gpio_saved_reg.icr1, port->base + GPIO_ICR1);

-- 
2.51.0

[PATCH v3 4/9] gpio: mxc: convert pad wakeup compatible checks to hwdata flags

[Peng Fan (OSS)]

From: Peng Fan <peng.fan@nxp.com>

mxc_gpio_generic_config() and mxc_gpio_set_pad_wakeup() call
of_device_is_compatible() on every invocation to determine pad wakeup
capability and i.MX8QM-specific behavior.  These properties are
invariant for the lifetime of the device.

Extend the hwdata flags scheme introduced in the previous commit with
MXC_GPIO_HAS_PAD_WAKEUP and MXC_GPIO_IS_IMX8QM, adding dedicated
hwdata instances for imx8qm and imx8qxp (also used by imx8dxl).
This replaces the repeated device tree string comparisons in the
suspend/resume path with simple flag tests on static per-compatible
data.

While at it, clean up mxc_gpio_generic_config() to use a local ret
variable for clarity instead of the == 0 comparison.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
---
 drivers/gpio/gpio-mxc.c | 46 ++++++++++++++++++++++++++++++++++------------
 1 file changed, 34 insertions(+), 12 deletions(-)

diff --git a/drivers/gpio/gpio-mxc.c b/drivers/gpio/gpio-mxc.c
index 5fbbfcebaa8f..1bd9f5beae4a 100644
--- a/drivers/gpio/gpio-mxc.c
+++ b/drivers/gpio/gpio-mxc.c
@@ -34,6 +34,8 @@
 #define IMX_SCU_WAKEUP_HIGH_LVL		7
 
 #define MXC_GPIO_HAS_POWER_OFF		BIT(0)
+#define MXC_GPIO_HAS_PAD_WAKEUP		BIT(1)
+#define MXC_GPIO_IS_IMX8QM		BIT(2)
 
 /* device type dependent stuff */
 struct mxc_gpio_hwdata {
@@ -132,6 +134,26 @@ static struct mxc_gpio_hwdata imx7d_gpio_hwdata = {
 	.flags = MXC_GPIO_HAS_POWER_OFF,
 };
 
+static struct mxc_gpio_hwdata imx8qm_gpio_hwdata = {
+	MXC_GPIO_HW_DATA_COMMON,
+	.flags = MXC_GPIO_IS_IMX8QM | MXC_GPIO_HAS_PAD_WAKEUP,
+};
+
+static struct mxc_gpio_hwdata imx8qxp_gpio_hwdata = {
+	MXC_GPIO_HW_DATA_COMMON,
+	.flags = MXC_GPIO_HAS_PAD_WAKEUP,
+};
+
+static inline bool mxc_gpio_is_imx8qm(struct mxc_gpio_port *port)
+{
+	return port->hwdata->flags & MXC_GPIO_IS_IMX8QM;
+}
+
+static inline bool mxc_gpio_has_pad_wakeup(struct mxc_gpio_port *port)
+{
+	return port->hwdata->flags & MXC_GPIO_HAS_PAD_WAKEUP;
+}
+
 static inline bool mxc_gpio_has_power_off(struct mxc_gpio_port *port)
 {
 	return port->hwdata->flags & MXC_GPIO_HAS_POWER_OFF;
@@ -158,9 +180,9 @@ static const struct of_device_id mxc_gpio_dt_ids[] = {
 	{ .compatible = "fsl,imx31-gpio", .data = &imx31_gpio_hwdata },
 	{ .compatible = "fsl,imx35-gpio", .data = &imx35_gpio_hwdata },
 	{ .compatible = "fsl,imx7d-gpio", .data = &imx7d_gpio_hwdata },
-	{ .compatible = "fsl,imx8dxl-gpio", .data = &imx35_gpio_hwdata },
-	{ .compatible = "fsl,imx8qm-gpio", .data = &imx35_gpio_hwdata },
-	{ .compatible = "fsl,imx8qxp-gpio", .data = &imx35_gpio_hwdata },
+	{ .compatible = "fsl,imx8dxl-gpio", .data = &imx8qxp_gpio_hwdata },
+	{ .compatible = "fsl,imx8qm-gpio", .data = &imx8qm_gpio_hwdata },
+	{ .compatible = "fsl,imx8qxp-gpio", .data = &imx8qxp_gpio_hwdata },
 	{ /* sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, mxc_gpio_dt_ids);
@@ -576,15 +598,16 @@ static void mxc_gpio_restore_regs(struct mxc_gpio_port *port)
 static bool mxc_gpio_generic_config(struct mxc_gpio_port *port,
 		unsigned int offset, unsigned long conf)
 {
-	struct device_node *np = port->dev->of_node;
+	int ret;
+
+	if (!mxc_gpio_has_pad_wakeup(port))
+		return false;
 
-	if (of_device_is_compatible(np, "fsl,imx8dxl-gpio") ||
-	    of_device_is_compatible(np, "fsl,imx8qxp-gpio") ||
-	    of_device_is_compatible(np, "fsl,imx8qm-gpio"))
-		return (gpiochip_generic_config(&port->gen_gc.gc,
-						offset, conf) == 0);
+	ret = gpiochip_generic_config(&port->gen_gc.gc, offset, conf);
+	if (ret)
+		return false;
 
-	return false;
+	return true;
 }
 
 static bool mxc_gpio_set_pad_wakeup(struct mxc_gpio_port *port, bool enable)
@@ -592,7 +615,6 @@ static bool mxc_gpio_set_pad_wakeup(struct mxc_gpio_port *port, bool enable)
 	unsigned long config;
 	bool ret = false;
 	int i, type;
-	bool is_imx8qm = of_device_is_compatible(port->dev->of_node, "fsl,imx8qm-gpio");
 
 	static const u32 pad_type_map[] = {
 		IMX_SCU_WAKEUP_OFF,		/* 0 */
@@ -613,7 +635,7 @@ static bool mxc_gpio_set_pad_wakeup(struct mxc_gpio_port *port, bool enable)
 		else
 			config = IMX_SCU_WAKEUP_OFF;
 
-		if (is_imx8qm && config == IMX_SCU_WAKEUP_FALL_EDGE) {
+		if (mxc_gpio_is_imx8qm(port) && config == IMX_SCU_WAKEUP_FALL_EDGE) {
 			dev_warn_once(port->dev,
 				      "No falling-edge support for wakeup on i.MX8QM\n");
 			config = IMX_SCU_WAKEUP_OFF;

-- 
2.51.0

Re: [PATCH v3 0/9] gpio: mxc: bug fixes and probe cleanup

[Peng Fan]

Ignore this V3 patchset. This is not a complete version.

Thanks
Peng

On Tue, Oct 06, 2026 at 08:31:05PM +0800, Peng Fan (OSS) wrote:
>This series cleans up the gpio-mxc driver in several incremental steps:
>bug fixes, converting runtime state to static per-compatible data,
>modernizing resource management with devres, and cleaning up
>register access patterns.
>
>Patches 1-2 are bug fixes:
>  - Fix a race where the chained IRQ handler is installed before probe
>    completes, allowing interrupts to fire on a half-initialized port.
>  - Fix wakeup_pads bit operations that used wrong set_bit/clear_bit
>    logic, folding in the assign_bit() simplification from V1.
>
>Patches 3-4 replace runtime of_device_is_compatible() calls with static
>per-compatible hwdata flags, eliminating repeated string comparisons in
>the suspend/resume path.
>
>Patches 5-6 convert probe error handling to devres and dev_err_probe().
>
>Patches 7-9 are cosmetic cleanups: local dev variable, MXC_ICR macros
>with field_prep/field_get, and BIT() macro for single-bit shifts.
>
>Signed-off-by: Peng Fan <peng.fan@nxp.com>
>---
>Changes in v3:
>- Patch 5/8 ("gpio: mxc: convert probe error handling to devres"):
>  Replaced pm_runtime_get_noresume() with
>  devm_pm_runtime_get_noresume() to fix a PM usage counter leak on
>  probe error paths. The non-devm pm_runtime_get_noresume() was not
>  balanced by any devres action, so any probe failure after the PM
>  block (e.g. -EPROBE_DEFER from devm_gpiochip_add_data()) would
>  leave usage_count permanently elevated, preventing runtime suspend
>  on re-probe.
>  Dropped the explicit pm_runtime_put_noidle() on
>  devm_pm_runtime_set_active_enabled() failure - the devres
>  registered by devm_pm_runtime_get_noresume() handles the balance
>  automatically during probe unwind.
>- Patch 6/8 ("gpio: mxc: use local dev variable"):
>  Keep of_device_is_compatible(), only focus on switching &pdev->dev to
>  dev.
>- Link to v2: https://patch.msgid.link/20261005-gpio-mxc-cleanup-v2-0-bdc3afbb35e2@nxp.com
>
>Changes in V2:
>- Reworked compatible-string caching (V1 patch 3) from probe-time bools
>  in mxc_gpio_port to static hwdata flags with per-compatible data
>  instances.  Split into two patches: one introducing the flags scheme
>  with MXC_GPIO_HW_DATA_COMMON macro for power_off (patch 3), one
>  extending it to pad_wakeup and imx8qm (patch 4).  (Frank, bot review)
>- Replaced devm_pm_runtime_get_noresume() + pm_runtime_set_active() +
>  devm_pm_runtime_enable() with devm_pm_runtime_set_active_enabled().
>  Keep plain pm_runtime_get_noresume() (non-devm) for the probe-scoped
>  reference to avoid usage_count underflow on unbind.  (Frank, bot review)
>- Replaced irq_domain_create_legacy() + devm_add_action_or_reset() with
>  devm_irq_domain_instantiate().  Squashed with the PM runtime devres
>  conversion (V1 patches 4+5) into a single patch (patch 5), since the
>  goto labels cannot be removed until both resources are devres-managed.
>- Split dev_err_probe() conversion into its own patch (patch 6) for
>  bisectability — patch 5 uses bare returns with correct error values.
>- Folded gpio_set_wake_irq() assign_bit simplification (V1 patch 9) into
>  the wakeup_pads fix (patch 2) where it belongs.
>- Used 0x3U (unsigned) in MXC_ICR_MASK() to avoid implementation-defined
>  behavior when shifting by 30 bits.
>- Replaced linux/of.h with linux/property.h to match the
>  of_device_is_compatible() → device_is_compatible() API change (patch 7).
>- Added return-value checks for devm_pm_runtime_set_active_enabled().
>- Fixed stale error code returns after devm_irq_alloc_descs() and
>  devm_irq_domain_instantiate() in the devres conversion patch.
>- Link to v1: https://patch.msgid.link/20261003-gpio-mxc-cleanup-v1-0-dad728ce27f2@nxp.com
>
>---
>Peng Fan (9):
>      gpio: mxc: fix race between chained IRQ handler install and probe completion
>      gpio: mxc: fix wakeup_pads bit operations
>      gpio: mxc: replace of_device_is_compatible() with hwdata flags
>      gpio: mxc: convert pad wakeup compatible checks to hwdata flags
>      gpio: mxc: convert probe error handling to devres
>      gpio: mxc: switch probe error paths to dev_err_probe()
>      gpio: mxc: use local dev variable
>      gpio: mxc: introduce MXC_ICR macros and use field_prep/field_get
>      gpio: mxc: use BIT() macro for single-bit operations
>
> drivers/gpio/gpio-mxc.c | 257 +++++++++++++++++++++++++++---------------------
> 1 file changed, 145 insertions(+), 112 deletions(-)
>---
>base-commit: f0406245cb9855e6318335a8a223551354291a46
>change-id: 20261003-gpio-mxc-cleanup-e49cc626c51e
>
>Best regards,
>--  
>Peng Fan <peng.fan@nxp.com>
>
>