* [Buildroot] [PATCH v7 0/3] board/lx2160ardb: new platform
@ 2026-10-19 7:47 Léo Denieul
2026-10-19 7:48 ` [Buildroot] [PATCH v7 1/3] package/qoriq-restool: add runtime dependencies Léo DENIEUL
` (2 more replies)
0 siblings, 3 replies; 15+ messages in thread
From: Léo Denieul @ 2026-10-19 7:47 UTC (permalink / raw)
To: buildroot; +Cc: Maxime Leroy, Vladimir Oltean, Vincent Jardin
Hello,
This series adds support for the NXP LX2160A-RDB board. It is a
repost of Maxime Leroy's v5 [1].
Changes v6 -> v7:
- resend with correct authorship (v6 was sent with wrong sender
addresses). No code change.
Changes v5 -> v6:
- patches 1/3 and 2/3: unchanged
- patch 3/3: increase BR2_TARGET_ROOTFS_EXT2_SIZE from 130M to
256M, the rootfs no longer fits in 130M on current master (it
needs about 148M: Linux ~100M, eudev/hwdb ~25M)
[1] https://patchwork.buildroot.org/project/buildroot/list/?series=366
Best regards,
Léo
Maxime Leroy (2):
package/qoriq-restool: add runtime dependencies
package/qoriq-restool: bump to lf-6.12.34-2.1.0
Vladimir Oltean (1):
board/lx2160ardb: new platform
board/freescale/common/env-dpaa2.txt | 7 +
.../udev/rules.d/74-dpaa2-networking.rules | 29 ++++
board/freescale/lx2160ardb/extlinux.conf | 4 +
board/freescale/lx2160ardb/genimage.cfg | 47 +++++++
.../arm-trusted-firmware.hash | 2 +
.../patches/linux-headers/linux-headers.hash | 1 +
.../lx2160ardb/patches/linux/linux.hash | 2 +
.../lx2160ardb/patches/uboot/uboot.hash | 2 +
board/freescale/lx2160ardb/post-build.sh | 11 ++
.../rcw_2200_750_3200_19_5_2_sd.rcw | 67 +++++++++
board/freescale/lx2160ardb/readme.txt | 129 ++++++++++++++++++
board/freescale/lx2160ardb/uboot-env.txt | 11 ++
board/freescale/lx2160ardb/uboot.config | 2 +
configs/lx2160ardb_defconfig | 59 ++++++++
package/qoriq-restool/Config.in | 9 ++
package/qoriq-restool/qoriq-restool.hash | 2 +-
package/qoriq-restool/qoriq-restool.mk | 2 +-
17 files changed, 384 insertions(+), 2 deletions(-)
create mode 100644 board/freescale/common/env-dpaa2.txt
create mode 100644 board/freescale/common/rootfs_overlay/etc/udev/rules.d/74-dpaa2-networking.rules
create mode 100644 board/freescale/lx2160ardb/extlinux.conf
create mode 100644 board/freescale/lx2160ardb/genimage.cfg
create mode 100644 board/freescale/lx2160ardb/patches/arm-trusted-firmware/arm-trusted-firmware.hash
create mode 120000 board/freescale/lx2160ardb/patches/linux-headers/linux-headers.hash
create mode 100644 board/freescale/lx2160ardb/patches/linux/linux.hash
create mode 100644 board/freescale/lx2160ardb/patches/uboot/uboot.hash
create mode 100755 board/freescale/lx2160ardb/post-build.sh
create mode 100644 board/freescale/lx2160ardb/rcw_2200_750_3200_19_5_2_sd.rcw
create mode 100644 board/freescale/lx2160ardb/readme.txt
create mode 100644 board/freescale/lx2160ardb/uboot-env.txt
create mode 100644 board/freescale/lx2160ardb/uboot.config
create mode 100644 configs/lx2160ardb_defconfig
--
2.53.0
_______________________________________________
buildroot mailing list
buildroot@buildroot.org
https://lists.buildroot.org/mailman/listinfo/buildroot
^ permalink raw reply [flat|nested] 15+ messages in thread* [Buildroot] [PATCH v7 1/3] package/qoriq-restool: add runtime dependencies 2026-10-19 7:47 [Buildroot] [PATCH v7 0/3] board/lx2160ardb: new platform Léo Denieul @ 2026-10-19 7:48 ` Léo DENIEUL 2026-10-25 21:24 ` Thomas Petazzoni via buildroot 2026-10-19 7:48 ` [Buildroot] [PATCH v7 2/3] package/qoriq-restool: bump to lf-6.12.34-2.1.0 Léo DENIEUL 2026-10-19 7:48 ` [Buildroot] [PATCH v7 3/3] board/lx2160ardb: new platform Léo DENIEUL 2 siblings, 1 reply; 15+ messages in thread From: Léo DENIEUL @ 2026-10-19 7:48 UTC (permalink / raw) To: buildroot; +Cc: Maxime Leroy, Vladimir Oltean, Vincent Jardin From: Maxime Leroy <maxime@leroys.fr> The scripts shipped with restool require: - bash: they use #!/bin/bash shebang and bash-specific features (shopt, declare -A) The ls-append-dpl script also requires: - dtc programs: the script uses dtc and fdtget commands Since dtc needs dynamic libraries, add the corresponding dependency. Signed-off-by: Maxime Leroy <maxime@leroys.fr> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> --- package/qoriq-restool/Config.in | 9 +++++++++ 1 file changed, 9 insertions(+) diff --git a/package/qoriq-restool/Config.in b/package/qoriq-restool/Config.in index 600c2c958d..46330e8cac 100644 --- a/package/qoriq-restool/Config.in +++ b/package/qoriq-restool/Config.in @@ -1,6 +1,11 @@ config BR2_PACKAGE_QORIQ_RESTOOL bool "qoriq-restool" depends on BR2_aarch64 || BR2_aarch64_be + depends on !BR2_STATIC_LIBS # dtc + select BR2_PACKAGE_BUSYBOX_SHOW_OTHERS if BR2_PACKAGE_BUSYBOX # bash + select BR2_PACKAGE_BASH + select BR2_PACKAGE_DTC + select BR2_PACKAGE_DTC_PROGRAMS help The DPAA2 architecture in Layerscape SoCs consists of networking resources that can be assembled into various @@ -19,3 +24,7 @@ config BR2_PACKAGE_QORIQ_RESTOOL that specified in the boot-time DPL file. https://github.com/nxp-qoriq/restool + +comment "qoriq-restool needs a toolchain w/ dynamic library" + depends on BR2_aarch64 || BR2_aarch64_be + depends on BR2_STATIC_LIBS -- 2.53.0 _______________________________________________ buildroot mailing list buildroot@buildroot.org https://lists.buildroot.org/mailman/listinfo/buildroot ^ permalink raw reply related [flat|nested] 15+ messages in thread
* Re: [Buildroot] [PATCH v7 1/3] package/qoriq-restool: add runtime dependencies 2026-10-19 7:48 ` [Buildroot] [PATCH v7 1/3] package/qoriq-restool: add runtime dependencies Léo DENIEUL @ 2026-10-25 21:24 ` Thomas Petazzoni via buildroot 0 siblings, 0 replies; 15+ messages in thread From: Thomas Petazzoni via buildroot @ 2026-10-25 21:24 UTC (permalink / raw) To: Léo DENIEUL; +Cc: buildroot, Maxime Leroy, Vladimir Oltean, Vincent Jardin On Mon, Oct 19, 2026 at 09:48:08AM +0200, Léo DENIEUL wrote: > From: Maxime Leroy <maxime@leroys.fr> > > The scripts shipped with restool require: > - bash: they use #!/bin/bash shebang and bash-specific > features (shopt, declare -A) > > The ls-append-dpl script also requires: > - dtc programs: the script uses dtc and fdtget commands > > Since dtc needs dynamic libraries, add the corresponding dependency. > > Signed-off-by: Maxime Leroy <maxime@leroys.fr> > Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Applied to master, thanks! Best regards, Thomas Petazzoni -- Thomas Petazzoni, co-owner and CEO, Bootlin Embedded Linux and Kernel engineering and training https://bootlin.com _______________________________________________ buildroot mailing list buildroot@buildroot.org https://lists.buildroot.org/mailman/listinfo/buildroot ^ permalink raw reply [flat|nested] 15+ messages in thread
* [Buildroot] [PATCH v7 2/3] package/qoriq-restool: bump to lf-6.12.34-2.1.0 2026-10-19 7:47 [Buildroot] [PATCH v7 0/3] board/lx2160ardb: new platform Léo Denieul 2026-10-19 7:48 ` [Buildroot] [PATCH v7 1/3] package/qoriq-restool: add runtime dependencies Léo DENIEUL @ 2026-10-19 7:48 ` Léo DENIEUL 2026-10-25 21:24 ` Thomas Petazzoni via buildroot 2026-10-19 7:48 ` [Buildroot] [PATCH v7 3/3] board/lx2160ardb: new platform Léo DENIEUL 2 siblings, 1 reply; 15+ messages in thread From: Léo DENIEUL @ 2026-10-19 7:48 UTC (permalink / raw) To: buildroot; +Cc: Maxime Leroy, Vladimir Oltean, Vincent Jardin From: Maxime Leroy <maxime@leroys.fr> Align with other NXP Layerscape components using the same tag. No code changes, just switching from commit hash to official release tag. Signed-off-by: Maxime Leroy <maxime@leroys.fr> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> --- package/qoriq-restool/qoriq-restool.hash | 2 +- package/qoriq-restool/qoriq-restool.mk | 2 +- 2 files changed, 2 insertions(+), 2 deletions(-) diff --git a/package/qoriq-restool/qoriq-restool.hash b/package/qoriq-restool/qoriq-restool.hash index 72a34473f2..77c6442269 100644 --- a/package/qoriq-restool/qoriq-restool.hash +++ b/package/qoriq-restool/qoriq-restool.hash @@ -1,3 +1,3 @@ # Locally calculated -sha256 2879f14c9dd810e92d4c51c7f1a3e6705a5a585c2445e507f63e39872ac6237d qoriq-restool-lf-6.12.20-2.0.0-3-gb44748e.tar.gz +sha256 5a17fad0645d943efcae215b2d99f93406f605000cd4f0d5d9df627bc6f4e631 qoriq-restool-lf-6.12.34-2.1.0.tar.gz sha256 ddc794a75f11c3bd01015f16b9776064a894015e7a1603541283ccbc2e1c3a40 LICENSE diff --git a/package/qoriq-restool/qoriq-restool.mk b/package/qoriq-restool/qoriq-restool.mk index 79e87ef1dd..3d16531def 100644 --- a/package/qoriq-restool/qoriq-restool.mk +++ b/package/qoriq-restool/qoriq-restool.mk @@ -4,7 +4,7 @@ # ################################################################################ -QORIQ_RESTOOL_VERSION = lf-6.12.20-2.0.0-3-gb44748e +QORIQ_RESTOOL_VERSION = lf-6.12.34-2.1.0 QORIQ_RESTOOL_SITE = $(call github,nxp-qoriq,restool,$(QORIQ_RESTOOL_VERSION)) QORIQ_RESTOOL_LICENSE = BSD-3-Clause or GPL-2.0+ QORIQ_RESTOOL_LICENSE_FILES = LICENSE -- 2.53.0 _______________________________________________ buildroot mailing list buildroot@buildroot.org https://lists.buildroot.org/mailman/listinfo/buildroot ^ permalink raw reply related [flat|nested] 15+ messages in thread
* Re: [Buildroot] [PATCH v7 2/3] package/qoriq-restool: bump to lf-6.12.34-2.1.0 2026-10-19 7:48 ` [Buildroot] [PATCH v7 2/3] package/qoriq-restool: bump to lf-6.12.34-2.1.0 Léo DENIEUL @ 2026-10-25 21:24 ` Thomas Petazzoni via buildroot 0 siblings, 0 replies; 15+ messages in thread From: Thomas Petazzoni via buildroot @ 2026-10-25 21:24 UTC (permalink / raw) To: Léo DENIEUL; +Cc: buildroot, Maxime Leroy, Vladimir Oltean, Vincent Jardin On Mon, Oct 19, 2026 at 09:48:20AM +0200, Léo DENIEUL wrote: > From: Maxime Leroy <maxime@leroys.fr> > > Align with other NXP Layerscape components using the same tag. > No code changes, just switching from commit hash to official release tag. > > Signed-off-by: Maxime Leroy <maxime@leroys.fr> > Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Applied to master, thanks! Best regards, Thomas Petazzoni -- Thomas Petazzoni, co-owner and CEO, Bootlin Embedded Linux and Kernel engineering and training https://bootlin.com _______________________________________________ buildroot mailing list buildroot@buildroot.org https://lists.buildroot.org/mailman/listinfo/buildroot ^ permalink raw reply [flat|nested] 15+ messages in thread
* [Buildroot] [PATCH v7 3/3] board/lx2160ardb: new platform 2026-10-19 7:47 [Buildroot] [PATCH v7 0/3] board/lx2160ardb: new platform Léo Denieul 2026-10-19 7:48 ` [Buildroot] [PATCH v7 1/3] package/qoriq-restool: add runtime dependencies Léo DENIEUL 2026-10-19 7:48 ` [Buildroot] [PATCH v7 2/3] package/qoriq-restool: bump to lf-6.12.34-2.1.0 Léo DENIEUL @ 2026-10-19 7:48 ` Léo DENIEUL 2026-10-25 21:25 ` Thomas Petazzoni via buildroot 2 siblings, 1 reply; 15+ messages in thread From: Léo DENIEUL @ 2026-10-19 7:48 UTC (permalink / raw) To: buildroot; +Cc: Maxime Leroy, Vladimir Oltean, Vincent Jardin From: Vladimir Oltean <olteanv@gmail.com> Add Buildroot support for the NXP LX2160A-RDB (reference design board). This is configured here to boot from the SD card. To my surprise, NXP RCWs for LX2160A rev2 silicon don't have a pre-existing example for SD boot, so until one is available, include the RCW through board files. The boot uses U-Boot's bootstd framework with extlinux.conf. The DPAA2 Management Complex firmware is loaded from the filesystem during U-Boot board init. EFI boot support is disabled since we use extlinux. Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Vincent Jardin <vjardin@free.fr> Tested-by: Maxime Leroy <maxime@leroys.fr> Signed-off-by: Maxime Leroy <maxime@leroys.fr> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Tested-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: Léo DENIEUL <leo.denieul.yoshino@gmail.com> --- Changes v6 -> v7: - resend with correct authorship (v6 was sent with wrong sender addresses) Changes v5 -> v6: - increase BR2_TARGET_ROOTFS_EXT2_SIZE from 130M to 256M: on current master the rootfs needs about 148M (Linux ~100M, eudev/hwdb ~25M) --- board/freescale/common/env-dpaa2.txt | 7 + .../udev/rules.d/74-dpaa2-networking.rules | 29 ++++ board/freescale/lx2160ardb/extlinux.conf | 4 + board/freescale/lx2160ardb/genimage.cfg | 47 +++++++ .../arm-trusted-firmware.hash | 2 + .../patches/linux-headers/linux-headers.hash | 1 + .../lx2160ardb/patches/linux/linux.hash | 2 + .../lx2160ardb/patches/uboot/uboot.hash | 2 + board/freescale/lx2160ardb/post-build.sh | 11 ++ .../rcw_2200_750_3200_19_5_2_sd.rcw | 67 +++++++++ board/freescale/lx2160ardb/readme.txt | 129 ++++++++++++++++++ board/freescale/lx2160ardb/uboot-env.txt | 11 ++ board/freescale/lx2160ardb/uboot.config | 2 + configs/lx2160ardb_defconfig | 59 ++++++++ 14 files changed, 373 insertions(+) create mode 100644 board/freescale/common/env-dpaa2.txt create mode 100644 board/freescale/common/rootfs_overlay/etc/udev/rules.d/74-dpaa2-networking.rules create mode 100644 board/freescale/lx2160ardb/extlinux.conf create mode 100644 board/freescale/lx2160ardb/genimage.cfg create mode 100644 board/freescale/lx2160ardb/patches/arm-trusted-firmware/arm-trusted-firmware.hash create mode 120000 board/freescale/lx2160ardb/patches/linux-headers/linux-headers.hash create mode 100644 board/freescale/lx2160ardb/patches/linux/linux.hash create mode 100644 board/freescale/lx2160ardb/patches/uboot/uboot.hash create mode 100755 board/freescale/lx2160ardb/post-build.sh create mode 100644 board/freescale/lx2160ardb/rcw_2200_750_3200_19_5_2_sd.rcw create mode 100644 board/freescale/lx2160ardb/readme.txt create mode 100644 board/freescale/lx2160ardb/uboot-env.txt create mode 100644 board/freescale/lx2160ardb/uboot.config create mode 100644 configs/lx2160ardb_defconfig diff --git a/board/freescale/common/env-dpaa2.txt b/board/freescale/common/env-dpaa2.txt new file mode 100644 index 0000000000..e60bcdeac0 --- /dev/null +++ b/board/freescale/common/env-dpaa2.txt @@ -0,0 +1,7 @@ +# DPAA2 MC firmware loading (common to all DPAA2 boards) +dpl_addr_r=0x80d00000 +dpc_addr_r=0x80e00000 +fsl_bootcmd_mcinitcmd_set=y +mc_fw_addr_r=0x80a00000 +mcinitcmd=mmc dev 0 && load mmc 0:1 $mc_fw_addr_r /boot/mc.itb && load mmc 0:1 $dpc_addr_r /boot/dpc.dtb && load mmc 0:1 $dpl_addr_r /boot/dpl.dtb && fsl_mc start mc $mc_fw_addr_r $dpc_addr_r && fsl_mc lazyapply dpl $dpl_addr_r +mcmemsize=0x70000000 diff --git a/board/freescale/common/rootfs_overlay/etc/udev/rules.d/74-dpaa2-networking.rules b/board/freescale/common/rootfs_overlay/etc/udev/rules.d/74-dpaa2-networking.rules new file mode 100644 index 0000000000..ac55225673 --- /dev/null +++ b/board/freescale/common/rootfs_overlay/etc/udev/rules.d/74-dpaa2-networking.rules @@ -0,0 +1,29 @@ +SUBSYSTEM!="net", GOTO="fsl_dpaa2_rules_end" +ACTION!="add|change|online|offline", GOTO="fsl_dpaa2_rules_end" + +# Rules that match on objects connected to DPMACs have priority, and are named +# after those DPMACs. +DRIVERS=="fsl_dpaa2_eth|fsl_dpaa2_switch", ENV{OF_FULLNAME}=="/soc/fsl-mc@80c000000/dpmacs/ethernet@1", NAME="endpmac1", GOTO="fsl_dpaa2_rules_end" +DRIVERS=="fsl_dpaa2_eth|fsl_dpaa2_switch", ENV{OF_FULLNAME}=="/soc/fsl-mc@80c000000/dpmacs/ethernet@2", NAME="endpmac2", GOTO="fsl_dpaa2_rules_end" +DRIVERS=="fsl_dpaa2_eth|fsl_dpaa2_switch", ENV{OF_FULLNAME}=="/soc/fsl-mc@80c000000/dpmacs/ethernet@3", NAME="endpmac3", GOTO="fsl_dpaa2_rules_end" +DRIVERS=="fsl_dpaa2_eth|fsl_dpaa2_switch", ENV{OF_FULLNAME}=="/soc/fsl-mc@80c000000/dpmacs/ethernet@4", NAME="endpmac4", GOTO="fsl_dpaa2_rules_end" +DRIVERS=="fsl_dpaa2_eth|fsl_dpaa2_switch", ENV{OF_FULLNAME}=="/soc/fsl-mc@80c000000/dpmacs/ethernet@5", NAME="endpmac5", GOTO="fsl_dpaa2_rules_end" +DRIVERS=="fsl_dpaa2_eth|fsl_dpaa2_switch", ENV{OF_FULLNAME}=="/soc/fsl-mc@80c000000/dpmacs/ethernet@6", NAME="endpmac6", GOTO="fsl_dpaa2_rules_end" +DRIVERS=="fsl_dpaa2_eth|fsl_dpaa2_switch", ENV{OF_FULLNAME}=="/soc/fsl-mc@80c000000/dpmacs/ethernet@7", NAME="endpmac7", GOTO="fsl_dpaa2_rules_end" +DRIVERS=="fsl_dpaa2_eth|fsl_dpaa2_switch", ENV{OF_FULLNAME}=="/soc/fsl-mc@80c000000/dpmacs/ethernet@8", NAME="endpmac8", GOTO="fsl_dpaa2_rules_end" +DRIVERS=="fsl_dpaa2_eth|fsl_dpaa2_switch", ENV{OF_FULLNAME}=="/soc/fsl-mc@80c000000/dpmacs/ethernet@9", NAME="endpmac9", GOTO="fsl_dpaa2_rules_end" +DRIVERS=="fsl_dpaa2_eth|fsl_dpaa2_switch", ENV{OF_FULLNAME}=="/soc/fsl-mc@80c000000/dpmacs/ethernet@a", NAME="endpmac10", GOTO="fsl_dpaa2_rules_end" +DRIVERS=="fsl_dpaa2_eth|fsl_dpaa2_switch", ENV{OF_FULLNAME}=="/soc/fsl-mc@80c000000/dpmacs/ethernet@11", NAME="endpmac17", GOTO="fsl_dpaa2_rules_end" +DRIVERS=="fsl_dpaa2_eth|fsl_dpaa2_switch", ENV{OF_FULLNAME}=="/soc/fsl-mc@80c000000/dpmacs/ethernet@12", NAME="endpmac18", GOTO="fsl_dpaa2_rules_end" + +# Rules that match on DPNI objects which are not connected to DPMACs, but to +# other DPNIs, DPSW ports, DPDMUX etc. Below is an example to set up a +# persistent MAC address, which can be extended beyond dpni.0. +# DRIVERS=="fsl_dpaa2_eth", DEVPATH=="/devices/platform/soc/80c000000.fsl-mc/dprc.[0-9]*/dpni.0/net/*", NAME="endpni0", PROGRAM="/sbin/ip link set %k address 00:01:02:03:04:05" + +# Rules that match on DPSW ports not connected to a DPMAC. +# Below is an example to set up a persistent MAC address, which can be extended +# beyond dpsw.0. +# DRIVERS=="fsl_dpaa2_switch", DEVPATH=="/devices/platform/soc/80c000000.fsl-mc/dprc.[0-9]*/dpsw.0/net/*", NAME="endpsw0%s{phys_port_name}", PROGRAM="/sbin/ip link set %k address 00:01:02:03:04:05" + +LABEL="fsl_dpaa2_rules_end" diff --git a/board/freescale/lx2160ardb/extlinux.conf b/board/freescale/lx2160ardb/extlinux.conf new file mode 100644 index 0000000000..58c2720252 --- /dev/null +++ b/board/freescale/lx2160ardb/extlinux.conf @@ -0,0 +1,4 @@ +label NXP LX2160A Reference Design Board + kernel /boot/Image + devicetree /boot/fsl-lx2160a-rdb.dtb + append console=ttyAMA0,115200 root=PARTUUID=%PARTUUID% rw rootwait cma=256M diff --git a/board/freescale/lx2160ardb/genimage.cfg b/board/freescale/lx2160ardb/genimage.cfg new file mode 100644 index 0000000000..f895a5ab5e --- /dev/null +++ b/board/freescale/lx2160ardb/genimage.cfg @@ -0,0 +1,47 @@ +image sdcard.img { + /* Primary GPT table needs to be moved to a region which does + * not collide with the RCW/PBI location + */ + hdimage { + partition-table-type = "gpt" + gpt-location = 6M + } + + partition rcw { + offset = 4K + in-partition-table = "no" + image = "bl2_sd.pbl" + } + + partition u-boot { + offset = 1M + in-partition-table = "no" + image = "fip.bin" + } + + partition u-boot-environment { + in-partition-table = "no" + image = "uboot-env.bin" + offset = 5M + } + + /* Offset must match PLAT_DDR_FIP_OFFSET from ATF */ + partition ddr-phy { + in-partition-table = "no" + image = "fip_ddr.bin" + offset = 8M + } + + /* Offset must match IN112525_FW_ADDR from U-Boot */ + partition 25ge-retimer-ucode { + in-partition-table = "no" + image = "in112525-phy-ucode.txt" + offset = 0x980000 + } + + partition rootfs { + bootable = "true" + image = "rootfs.ext4" + partition-uuid = %PARTUUID% + } +} diff --git a/board/freescale/lx2160ardb/patches/arm-trusted-firmware/arm-trusted-firmware.hash b/board/freescale/lx2160ardb/patches/arm-trusted-firmware/arm-trusted-firmware.hash new file mode 100644 index 0000000000..4b761bede3 --- /dev/null +++ b/board/freescale/lx2160ardb/patches/arm-trusted-firmware/arm-trusted-firmware.hash @@ -0,0 +1,2 @@ +# Locally computed +sha256 2d3f9c52e16766c290bdc0bc130d634e4c326a5b236dfb2f2ca3f0fa457e82d4 atf-lf-6.12.34-2.1.0.tar.gz diff --git a/board/freescale/lx2160ardb/patches/linux-headers/linux-headers.hash b/board/freescale/lx2160ardb/patches/linux-headers/linux-headers.hash new file mode 120000 index 0000000000..5808d92afe --- /dev/null +++ b/board/freescale/lx2160ardb/patches/linux-headers/linux-headers.hash @@ -0,0 +1 @@ +../linux/linux.hash \ No newline at end of file diff --git a/board/freescale/lx2160ardb/patches/linux/linux.hash b/board/freescale/lx2160ardb/patches/linux/linux.hash new file mode 100644 index 0000000000..f30030c86a --- /dev/null +++ b/board/freescale/lx2160ardb/patches/linux/linux.hash @@ -0,0 +1,2 @@ +# Locally computed +sha256 27a1987ca0a5802d3ebb296b8134ec66d813ad86cf2a60779b45092735bbb23b linux-lf-6.12.34-2.1.0.tar.gz diff --git a/board/freescale/lx2160ardb/patches/uboot/uboot.hash b/board/freescale/lx2160ardb/patches/uboot/uboot.hash new file mode 100644 index 0000000000..38d54d9922 --- /dev/null +++ b/board/freescale/lx2160ardb/patches/uboot/uboot.hash @@ -0,0 +1,2 @@ +# Locally computed +sha256 2f25cde388b2f83ff7a8e3afe25aafb1db48dafb0fa3bf1e4f9fef603f3b4785 u-boot-lf-6.12.34-2.1.0.tar.gz diff --git a/board/freescale/lx2160ardb/post-build.sh b/board/freescale/lx2160ardb/post-build.sh new file mode 100755 index 0000000000..4042bf9c7e --- /dev/null +++ b/board/freescale/lx2160ardb/post-build.sh @@ -0,0 +1,11 @@ +#!/bin/sh + +BOARD_DIR="$(dirname "$0")" +PARTUUID="$("$HOST_DIR/bin/uuidgen")" + +install -d "$TARGET_DIR/boot/extlinux/" +# Default DPL and DPC selections for mcinitcmd +ln -sf dpc-usxgmii.dtb "$TARGET_DIR/boot/dpc.dtb" +ln -sf dpl-eth.19.dtb "$TARGET_DIR/boot/dpl.dtb" +sed "s/%PARTUUID%/$PARTUUID/g" "$BOARD_DIR/extlinux.conf" > "$TARGET_DIR/boot/extlinux/extlinux.conf" +sed "s/%PARTUUID%/$PARTUUID/g" "$BOARD_DIR/genimage.cfg" > "$BINARIES_DIR/genimage.cfg" diff --git a/board/freescale/lx2160ardb/rcw_2200_750_3200_19_5_2_sd.rcw b/board/freescale/lx2160ardb/rcw_2200_750_3200_19_5_2_sd.rcw new file mode 100644 index 0000000000..4c4b7d9c79 --- /dev/null +++ b/board/freescale/lx2160ardb/rcw_2200_750_3200_19_5_2_sd.rcw @@ -0,0 +1,67 @@ +/* + * SerDes Protocol 1 - 19 + * SerDes Protocol 2 - 5 + * SerDes Protocol 3 - 2 + * + * Frequencies: + * Core -- 2200 MHz + * Platform -- 750 MHz + * DDR -- 3200 MT/s + */ + +#include <../lx2160asi/lx2160a.rcwi> + +SYS_PLL_RAT=15 +MEM_PLL_CFG=3 +MEM_PLL_RAT=32 +MEM2_PLL_CFG=3 +MEM2_PLL_RAT=32 +CGA_PLL1_RAT=22 +CGA_PLL2_RAT=22 +CGB_PLL1_RAT=22 +CGB_PLL2_RAT=9 +HWA_CGA_M1_CLK_SEL=1 +HWA_CGB_M1_CLK_SEL=6 +BOOT_LOC=8 +SYSCLK_FREQ=600 +IIC2_PMUX=6 +IIC3_PMUX=2 +IIC4_PMUX=2 +USB3_CLK_FSEL=39 +SRDS_PLL_PD_PLL5=1 +SRDS_PRTCL_S1=19 +SRDS_PRTCL_S2=5 +SRDS_PRTCL_S3=2 +SRDS_PLL_REF_CLK_SEL_S1=2 +SRDS_DIV_PEX_S1=1 +SRDS_DIV_PEX_S2=1 +SRDS_DIV_PEX_S3=1 + +/* Errata to write on scratch reg for validation */ +#include <../lx2160asi/scratchrw1.rcw> + +/* Boot Location Pointer */ +#include <../lx2160asi/bootlocptr_sd.rcw> + +/* Errata for SATA controller */ +#include <../lx2160asi/a010554.rcw> + +/* common PBI commands */ +#include <../lx2160asi/common.rcw> + +/* Modify FlexSPI Clock Divisor value */ +#include <../lx2160asi/flexspi_divisor_32.rcw> + +/*PCIe Errata A-009531*/ +#include <../lx2160asi/a009531_PEX3.rcw> +#include <../lx2160asi/a009531_PEX5.rcw> + +/*PCIe Errata A-008851*/ +#include <../lx2160asi/a008851_PEX3.rcw> +#include <../lx2160asi/a008851_PEX5.rcw> + +/*SerDes Errata A-050479*/ +#include <../lx2160asi/a050479.rcw> + +/* Errata A-050426 */ +#include <../lx2160asi/a050426.rcw> diff --git a/board/freescale/lx2160ardb/readme.txt b/board/freescale/lx2160ardb/readme.txt new file mode 100644 index 0000000000..287285a148 --- /dev/null +++ b/board/freescale/lx2160ardb/readme.txt @@ -0,0 +1,129 @@ +************** +NXP LX2160ARDB +************** + +This file documents the Buildroot support for the LX2160A Reference Design Board. + +For more details about the board and the QorIQ Layerscape SoC, see the +following pages (notably the "LX2160A Reference Design Board Getting Started +Guide", for which this guide serves as an addition, not a replacement): + - https://www.nxp.com/design/design-center/software/qoriq-developer-resources/layerscape-lx2160a-reference-design-board:LX2160A-RDB + - https://www.nxp.com/LX2160A + +Layerscape platforms are officially supported by NXP under the Layerscape +Debian Linux SDK (LDLSDK). This uses components from Linux Factory (project +common with i.MX), but has a slower release cadence than LF. The currently used +tag is lf-6.12.34-2.1.0, which is in line with the latest LF tag. Generally, in +Buildroot, the latest Linux Factory release tag is always used, which may be +considered pre-release software, as it may contain features which are not yet +documented, and it generally undergoes less testing. + +For the software Layerscape Debian Linux SDK User Guide, see: + - https://docs.nxp.com/bundle/UG10143/page/topics/about_this_document.html + - https://www.nxp.com/docs/en/user-guide/UG10143.pdf + +The components from NXP are: + - atf (fork), lf-6.12.34-2.1.0 + - linux (fork), lf-6.12.34-2.1.0 + - qoriq-ddr-phy-binary (blob), lf-6.12.34-2.1.0 + - qoriq-firmware-inphi (blob), static commit + - qoriq-mc-binary (blob), mc_release_10.39.0 + - qoriq-mc-utils, mc_release_10.39.0 + - qoriq-rcw, lf-6.12.34-2.1.0 + - qoriq-restool, lf-6.12.34-2.1.0 + - uboot (fork), lf-6.12.34-2.1.0 + +Build +===== + +First, configure Buildroot for the LX2160ARDB board: + + make lx2160ardb_defconfig + +Build all components: + + make + +You will find in output/images/ the following files: + - bl2_sd.pbl - RCW + ATF BL2 stage + - dpc-usxgmii.dtb - the default DPC file + - dpc-warn.dtb + - dpl-2dpni.dtb + - dpl-eth.19.dtb - the default DPL file + - fip_ddr.bin - DDR PHY firmware + - fip.bin - U-Boot packaged as ATF payload + - fsl-lx2160a-rdb.dtb + - Image + - in112525-phy-ucode.txt - Firmware file for 25GbE SFP+ retimer + - mc.itb - MC firmware + - PBL.bin + - rootfs.ext2 + - rootfs.ext4 + - sdcard.img + - u-boot.bin + - uboot-env.bin + +Create a bootable SD card +========================= + +To determine the device associated to the SD card have a look in the +/proc/partitions file: + + cat /proc/partitions + +Buildroot prepares a bootable "sdcard.img" image in the output/images/ +directory, ready to be dumped on a SD card. Launch the following +command as root: + + dd if=output/images/sdcard.img of=/dev/sdX + +The SD card image can also be programmed from a live system running U-Boot: + + => setenv autoload off && tftp $load_addr sdcard.img && mmc dev 0 && mmc write $load_addr 0 0x80000 + +*** WARNING! This will destroy all the card content. Use with care! *** + +For details about the medium image layout, see the definition in +board/freescale/lx2160ardb/genimage.cfg. + +Boot the LX2160ARDB board +========================= + +To boot your newly created system: +- insert the SD card in the SD slot of the board; +- Configure the switches SW1[1:4] = 0b1000 (select SD Card boot option), + or alternatively, run "qixis_reset sd" from a U-Boot booted from a different + boot source (NOR, eMMC etc). +- put a DB9F cable into the UART1 Port and connect using a terminal + emulator at 115200 bps, 8n1; +- power on the board. + +The DPL and DPC files provided by NXP are not maximal configurations. +They only contain a static description for: +- the 40GbE QSFP+ MAC2 (which implicitly has MAC_LINK_TYPE_FIXED, because its + entry is missing from the DPC, and this means that the link state is provided + by the MC firmware) +- the 1GbE RGMII MAC17 (specified as MAC_LINK_TYPE_PHY in the DPC, which means + that the link state is provided by phylink). + +The extra interfaces routed to front panel ports are endpmac3, endpmac4, +endpmac5, endpmac6 and endpmac18. Among the more usual networking choices, one +could create individual DPNIs for each MAC: + +$ ls-addni dpmac.3 && ls-addni dpmac.4 && ls-addni dpmac.5 && ls-addni dpmac.6 && ls-addni dpmac.18 + +or a DPSW object to accelerate L2 forwarding between them: + +$ ls-addsw --num-ifs=4 --max-fdbs=4 --flooding-cfg=DPSW_FLOODING_PER_FDB \ + --broadcast-cfg=DPSW_BROADCAST_PER_FDB dpmac.3 dpmac.4 dpmac.5 dpmac.6 +$ ip link add br0 type bridge vlan_filtering 1 && ip link set br0 up +$ for eth in endpmac3 endpmac4 endpmac5 endpmac6; do \ + ip link set $eth master br0 && ip link set $eth up; done + +Once the runtime configuration is satisfactory, it can be converted back into a +permanent DPL file which can be plugged back into the build system: + +$ restool dprc generate-dpl > dpl-new.dts + +Using the device tree compiler (dtc), the new DPL can be transformed into a +.dtb file and deployed as a custom networking configuration upon the next boot. diff --git a/board/freescale/lx2160ardb/uboot-env.txt b/board/freescale/lx2160ardb/uboot-env.txt new file mode 100644 index 0000000000..89090edb32 --- /dev/null +++ b/board/freescale/lx2160ardb/uboot-env.txt @@ -0,0 +1,11 @@ +# Memory addresses for bootstd +fdt_addr_r=0x90000000 +kernel_addr_r=0x81000000 +scriptaddr=0x80000000 + +# Boot order and network +boot_targets=usb0 mmc0 mmc1 scsi0 dhcp +ethprime=DPMAC1@xgmii + +# Boot command (MC already loaded via fsl_bootcmd_mcinitcmd_set) +bootcmd=bootflow scan diff --git a/board/freescale/lx2160ardb/uboot.config b/board/freescale/lx2160ardb/uboot.config new file mode 100644 index 0000000000..e31254d62e --- /dev/null +++ b/board/freescale/lx2160ardb/uboot.config @@ -0,0 +1,2 @@ +# Disable EFI boot support - we use extlinux.conf via bootstd instead +# CONFIG_EFI_LOADER is not set diff --git a/configs/lx2160ardb_defconfig b/configs/lx2160ardb_defconfig new file mode 100644 index 0000000000..8678bb2df4 --- /dev/null +++ b/configs/lx2160ardb_defconfig @@ -0,0 +1,59 @@ +BR2_aarch64=y +BR2_cortex_a72=y +BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_6_12=y +BR2_GLOBAL_PATCH_DIR="board/freescale/lx2160ardb/patches" +BR2_DOWNLOAD_FORCE_CHECK_HASHES=y +BR2_TARGET_GENERIC_HOSTNAME="lx2160ardb" +BR2_ROOTFS_DEVICE_CREATION_DYNAMIC_EUDEV=y +BR2_TARGET_GENERIC_GETTY_PORT="ttyAMA0" +BR2_ROOTFS_OVERLAY="board/freescale/common/rootfs_overlay" +BR2_ROOTFS_POST_BUILD_SCRIPT="board/freescale/lx2160ardb/post-build.sh" +BR2_ROOTFS_POST_IMAGE_SCRIPT="support/scripts/genimage.sh" +BR2_ROOTFS_POST_SCRIPT_ARGS="-c $(BINARIES_DIR)/genimage.cfg" +BR2_LINUX_KERNEL=y +BR2_LINUX_KERNEL_CUSTOM_TARBALL=y +BR2_LINUX_KERNEL_CUSTOM_TARBALL_LOCATION="$(call github,nxp-qoriq,linux,lf-6.12.34-2.1.0)/linux-lf-6.12.34-2.1.0.tar.gz" +BR2_LINUX_KERNEL_USE_ARCH_DEFAULT_CONFIG=y +BR2_LINUX_KERNEL_CONFIG_FRAGMENT_FILES="$(LINUX_DIR)/arch/arm64/configs/lsdk.config" +BR2_LINUX_KERNEL_DTS_SUPPORT=y +BR2_LINUX_KERNEL_INTREE_DTS_NAME="freescale/fsl-lx2160a-rdb" +BR2_LINUX_KERNEL_INSTALL_TARGET=y +BR2_TARGET_ROOTFS_EXT2=y +BR2_TARGET_ROOTFS_EXT2_4=y +BR2_TARGET_ROOTFS_EXT2_SIZE="256M" +BR2_TARGET_ROOTFS_CPIO=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_TARBALL=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_TARBALL_LOCATION="$(call github,nxp-qoriq,atf,lf-6.12.34-2.1.0)/atf-lf-6.12.34-2.1.0.tar.gz" +BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM="lx2160ardb" +BR2_TARGET_ARM_TRUSTED_FIRMWARE_FIP=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE_RCW=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE_UBOOT_AS_BL33=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE_ADDITIONAL_VARIABLES="BOOT_MODE=sd" +BR2_TARGET_ARM_TRUSTED_FIRMWARE_IMAGES="fip.bin bl2_sd.pbl" +BR2_TARGET_UBOOT=y +BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y +BR2_TARGET_UBOOT_CUSTOM_TARBALL=y +BR2_TARGET_UBOOT_CUSTOM_TARBALL_LOCATION="$(call github,nxp-qoriq,u-boot,lf-6.12.34-2.1.0)/u-boot-lf-6.12.34-2.1.0.tar.gz" +BR2_TARGET_UBOOT_BOARD_DEFCONFIG="lx2160ardb_tfa" +BR2_TARGET_UBOOT_CONFIG_FRAGMENT_FILES="board/freescale/lx2160ardb/uboot.config" +BR2_TARGET_UBOOT_NEEDS_DTC=y +BR2_TARGET_UBOOT_NEEDS_GNUTLS=y +BR2_PACKAGE_HOST_GENIMAGE=y +BR2_PACKAGE_HOST_QORIQ_RCW=y +BR2_PACKAGE_HOST_QORIQ_RCW_CUSTOM_PATH="board/freescale/lx2160ardb/rcw_2200_750_3200_19_5_2_sd.rcw" +BR2_PACKAGE_HOST_UBOOT_TOOLS=y +BR2_PACKAGE_HOST_UBOOT_TOOLS_ENVIMAGE=y +# Minimal U-Boot environment for bootstd with DPAA2 MC firmware init +BR2_PACKAGE_HOST_UBOOT_TOOLS_ENVIMAGE_SOURCE="board/freescale/lx2160ardb/uboot-env.txt board/freescale/common/env-dpaa2.txt" +BR2_PACKAGE_HOST_UBOOT_TOOLS_ENVIMAGE_SIZE="0x2000" +BR2_PACKAGE_QORIQ_DDR_PHY_BINARY=y +BR2_PACKAGE_QORIQ_MC_BINARY=y +BR2_PACKAGE_QORIQ_MC_BINARY_TARGET_LX2160A=y +BR2_PACKAGE_QORIQ_MC_BINARY_TARGET_INSTALL_PATH="boot" +BR2_PACKAGE_QORIQ_MC_UTILS=y +BR2_PACKAGE_QORIQ_MC_UTILS_DPC_INTREE="lx2160a/LX2160A-RDB/dpc-usxgmii lx2160a/LX2160A-RDB/dpc-warn" +BR2_PACKAGE_QORIQ_MC_UTILS_DPL_INTREE="lx2160a/LX2160A-RDB/dpl-2dpni lx2160a/LX2160A-RDB/dpl-eth.19" +BR2_PACKAGE_QORIQ_MC_UTILS_TARGET_INSTALL_PATH="boot" +BR2_PACKAGE_QORIQ_RESTOOL=y +BR2_PACKAGE_QORIQ_FIRMWARE_INPHI=y -- 2.53.0 _______________________________________________ buildroot mailing list buildroot@buildroot.org https://lists.buildroot.org/mailman/listinfo/buildroot ^ permalink raw reply related [flat|nested] 15+ messages in thread
* Re: [Buildroot] [PATCH v7 3/3] board/lx2160ardb: new platform 2026-10-19 7:48 ` [Buildroot] [PATCH v7 3/3] board/lx2160ardb: new platform Léo DENIEUL @ 2026-10-25 21:25 ` Thomas Petazzoni via buildroot 2026-10-26 10:15 ` Léo DENIEUL 0 siblings, 1 reply; 15+ messages in thread From: Thomas Petazzoni via buildroot @ 2026-10-25 21:25 UTC (permalink / raw) To: Léo DENIEUL; +Cc: buildroot, Maxime Leroy, Vladimir Oltean, Vincent Jardin On Mon, Oct 19, 2026 at 09:48:37AM +0200, Léo DENIEUL wrote: > From: Vladimir Oltean <olteanv@gmail.com> > > Add Buildroot support for the NXP LX2160A-RDB (reference design board). > This is configured here to boot from the SD card. To my surprise, NXP > RCWs for LX2160A rev2 silicon don't have a pre-existing example for SD > boot, so until one is available, include the RCW through board files. > > The boot uses U-Boot's bootstd framework with extlinux.conf. The DPAA2 > Management Complex firmware is loaded from the filesystem during U-Boot > board init. EFI boot support is disabled since we use extlinux. > > Signed-off-by: Vladimir Oltean <olteanv@gmail.com> > Reviewed-by: Vincent Jardin <vjardin@free.fr> > Tested-by: Maxime Leroy <maxime@leroys.fr> > Signed-off-by: Maxime Leroy <maxime@leroys.fr> > Reviewed-by: Vladimir Oltean <olteanv@gmail.com> > Tested-by: Vladimir Oltean <olteanv@gmail.com> > Signed-off-by: Léo DENIEUL <leo.denieul.yoshino@gmail.com> Thanks, seems a bit complicated, but fair enough. Since you did not add any entry in the DEVELOPERS file, who volunteers to maintain this platform? Note: we can add multiple people, that's not a problem. If you provide this information, I'll adjust the patch and apply. Thanks for your feedback! Thomas Petazzoni -- Thomas Petazzoni, co-owner and CEO, Bootlin Embedded Linux and Kernel engineering and training https://bootlin.com _______________________________________________ buildroot mailing list buildroot@buildroot.org https://lists.buildroot.org/mailman/listinfo/buildroot ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [Buildroot] [PATCH v7 3/3] board/lx2160ardb: new platform 2026-10-25 21:25 ` Thomas Petazzoni via buildroot @ 2026-10-26 10:15 ` Léo DENIEUL 2026-10-28 15:41 ` Vladimir Oltean 0 siblings, 1 reply; 15+ messages in thread From: Léo DENIEUL @ 2026-10-26 10:15 UTC (permalink / raw) To: Thomas Petazzoni; +Cc: buildroot, Maxime Leroy, Vladimir Oltean, Vincent Jardin Hello Thomas, On Sun, Oct 25, 2026 at 10:25:xx PM, Thomas Petazzoni wrote: > Since you did not add any entry in the DEVELOPERS file, who volunteers > to maintain this platform? Note: we can add multiple people, that's not > a problem. I'm happy to maintain this platform, please add me: N: Léo DENIEUL <leo.denieul.yoshino@gmail.com> F: board/nxp/lx2160ardb/ F: configs/lx2160ardb_defconfig Vladimir, as the original author of this support, you certainly deserve to be listed too, and you know the platform much better than I do. Would you like to be added? Thanks, Léo Le dim. 25 oct. 2026 à 22:25, Thomas Petazzoni <thomas.petazzoni@bootlin.com> a écrit : > > On Mon, Oct 19, 2026 at 09:48:37AM +0200, Léo DENIEUL wrote: > > From: Vladimir Oltean <olteanv@gmail.com> > > > > Add Buildroot support for the NXP LX2160A-RDB (reference design board). > > This is configured here to boot from the SD card. To my surprise, NXP > > RCWs for LX2160A rev2 silicon don't have a pre-existing example for SD > > boot, so until one is available, include the RCW through board files. > > > > The boot uses U-Boot's bootstd framework with extlinux.conf. The DPAA2 > > Management Complex firmware is loaded from the filesystem during U-Boot > > board init. EFI boot support is disabled since we use extlinux. > > > > Signed-off-by: Vladimir Oltean <olteanv@gmail.com> > > Reviewed-by: Vincent Jardin <vjardin@free.fr> > > Tested-by: Maxime Leroy <maxime@leroys.fr> > > Signed-off-by: Maxime Leroy <maxime@leroys.fr> > > Reviewed-by: Vladimir Oltean <olteanv@gmail.com> > > Tested-by: Vladimir Oltean <olteanv@gmail.com> > > Signed-off-by: Léo DENIEUL <leo.denieul.yoshino@gmail.com> > > Thanks, seems a bit complicated, but fair enough. Since you did not > add any entry in the DEVELOPERS file, who volunteers to maintain this > platform? Note: we can add multiple people, that's not a problem. If > you provide this information, I'll adjust the patch and apply. > > Thanks for your feedback! > > Thomas Petazzoni > -- > Thomas Petazzoni, co-owner and CEO, Bootlin > Embedded Linux and Kernel engineering and training > https://bootlin.com _______________________________________________ buildroot mailing list buildroot@buildroot.org https://lists.buildroot.org/mailman/listinfo/buildroot ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [Buildroot] [PATCH v7 3/3] board/lx2160ardb: new platform 2026-10-26 10:15 ` Léo DENIEUL @ 2026-10-28 15:41 ` Vladimir Oltean 2026-11-05 15:36 ` [Buildroot] [PATCH v8 0/2] board/lx2160ardb board/lx2160a-rdb new platform and newconfig Léo DENIEUL ` (2 more replies) 0 siblings, 3 replies; 15+ messages in thread From: Vladimir Oltean @ 2026-10-28 15:41 UTC (permalink / raw) To: Léo DENIEUL, Thomas Petazzoni Cc: buildroot, Maxime Leroy, Vincent Jardin On Mon, Oct 26, 2026 at 11:15:47AM +0100, Léo DENIEUL wrote: > Hello Thomas, > > On Sun, Oct 25, 2026 at 10:25:xx PM, Thomas Petazzoni wrote: > > Since you did not add any entry in the DEVELOPERS file, who volunteers > > to maintain this platform? Note: we can add multiple people, that's not > > a problem. > > I'm happy to maintain this platform, please add me: > > N: Léo DENIEUL <leo.denieul.yoshino@gmail.com> > F: board/nxp/lx2160ardb/ > F: configs/lx2160ardb_defconfig > > Vladimir, as the original author of this support, you certainly deserve > to be listed too, and you know the platform much better than I do. > Would you like to be added? > > Thanks, > Léo I'd like to try and stay involved even if I don't have a lot of spare time. So Thomas, if it's not a problem, please add me alongside Léo as well. Thanks! _______________________________________________ buildroot mailing list buildroot@buildroot.org https://lists.buildroot.org/mailman/listinfo/buildroot ^ permalink raw reply [flat|nested] 15+ messages in thread
* [Buildroot] [PATCH v8 0/2] board/lx2160ardb board/lx2160a-rdb new platform and newconfig 2026-10-28 15:41 ` Vladimir Oltean @ 2026-11-05 15:36 ` Léo DENIEUL 2026-11-05 15:47 ` Leo DENIEUL 2026-11-05 15:36 ` [Buildroot] [PATCH v8 1/2] board/lx2160ardb: new platform Vladimir Oltean 2026-11-05 15:37 ` [Buildroot] [PATCH v8 2/2] configs/lx2160a-rdb: new defconfig Léo DENIEUL 2 siblings, 1 reply; 15+ messages in thread From: Léo DENIEUL @ 2026-11-05 15:36 UTC (permalink / raw) To: buildroot; +Cc: Thomas Petazzoni, Vladimir Oltean, Maxime Leroy, Vincent Jardin Hello, This v8 replaces v7, following Thomas' review: - patch 1/2 is v7 3/3 with the DEVELOPERS entries Thomas asked for (Vladimir Oltean and myself). The defconfig is renamed freescale_lx2160ardb_defconfig, as it uses the NXP BSP forks. - patch 2/2 adds lx2160a-rdb_defconfig, a variant of the same board using upstream TF-A v2.15.0, U-Boot 2026.10 and Linux 6.18.60. It reuses the board files from board/freescale/lx2160ardb/ and carries its own hashes and genimage.cfg in board/freescale/lx2160a-rdb/. The naming follows the existing freescale_imx8mpevk (NXP BSP) / imx8mp-evk (upstream) pair. Vladimir, I listed you for the NXP BSP variant as agreed. Changes v7 -> v8: - add DEVELOPERS entries - rename lx2160ardb_defconfig to freescale_lx2160ardb_defconfig - new patch 2/2: upstream variant lx2160a-rdb Best regards, Léo Léo DENIEUL (1): configs/lx2160a-rdb: new defconfig Vladimir Oltean (1): board/lx2160ardb: new platform DEVELOPERS | 7 + board/freescale/common/env-dpaa2.txt | 7 + .../udev/rules.d/74-dpaa2-networking.rules | 29 ++++ board/freescale/lx2160a-rdb/extlinux.conf | 1 + board/freescale/lx2160a-rdb/genimage.cfg | 40 ++++++ .../arm-trusted-firmware.hash | 2 + .../patches/linux-headers/linux-headers.hash | 2 + .../lx2160a-rdb/patches/linux/linux.hash | 2 + .../lx2160a-rdb/patches/uboot/uboot.hash | 2 + board/freescale/lx2160a-rdb/post-build.sh | 11 ++ board/freescale/lx2160a-rdb/readme.txt | 46 +++++++ board/freescale/lx2160ardb/extlinux.conf | 4 + board/freescale/lx2160ardb/genimage.cfg | 47 +++++++ .../arm-trusted-firmware.hash | 2 + .../patches/linux-headers/linux-headers.hash | 1 + .../lx2160ardb/patches/linux/linux.hash | 2 + .../lx2160ardb/patches/uboot/uboot.hash | 2 + board/freescale/lx2160ardb/post-build.sh | 11 ++ .../rcw_2200_750_3200_19_5_2_sd.rcw | 67 +++++++++ board/freescale/lx2160ardb/readme.txt | 129 ++++++++++++++++++ board/freescale/lx2160ardb/uboot-env.txt | 11 ++ board/freescale/lx2160ardb/uboot.config | 2 + configs/freescale_lx2160ardb_defconfig | 59 ++++++++ configs/lx2160a-rdb_defconfig | 56 ++++++++ 24 files changed, 542 insertions(+) create mode 100644 board/freescale/common/env-dpaa2.txt create mode 100644 board/freescale/common/rootfs_overlay/etc/udev/rules.d/74-dpaa2-networking.rules create mode 120000 board/freescale/lx2160a-rdb/extlinux.conf create mode 100644 board/freescale/lx2160a-rdb/genimage.cfg create mode 100644 board/freescale/lx2160a-rdb/patches/arm-trusted-firmware/arm-trusted-firmware.hash create mode 100644 board/freescale/lx2160a-rdb/patches/linux-headers/linux-headers.hash create mode 100644 board/freescale/lx2160a-rdb/patches/linux/linux.hash create mode 100644 board/freescale/lx2160a-rdb/patches/uboot/uboot.hash create mode 100755 board/freescale/lx2160a-rdb/post-build.sh create mode 100644 board/freescale/lx2160a-rdb/readme.txt create mode 100644 board/freescale/lx2160ardb/extlinux.conf create mode 100644 board/freescale/lx2160ardb/genimage.cfg create mode 100644 board/freescale/lx2160ardb/patches/arm-trusted-firmware/arm-trusted-firmware.hash create mode 120000 board/freescale/lx2160ardb/patches/linux-headers/linux-headers.hash create mode 100644 board/freescale/lx2160ardb/patches/linux/linux.hash create mode 100644 board/freescale/lx2160ardb/patches/uboot/uboot.hash create mode 100755 board/freescale/lx2160ardb/post-build.sh create mode 100644 board/freescale/lx2160ardb/rcw_2200_750_3200_19_5_2_sd.rcw create mode 100644 board/freescale/lx2160ardb/readme.txt create mode 100644 board/freescale/lx2160ardb/uboot-env.txt create mode 100644 board/freescale/lx2160ardb/uboot.config create mode 100644 configs/freescale_lx2160ardb_defconfig create mode 100644 configs/lx2160a-rdb_defconfig base-commit: d1fad27e965805c0e4e201994021cd9acf48b0a5 -- 2.53.0 _______________________________________________ buildroot mailing list buildroot@buildroot.org https://lists.buildroot.org/mailman/listinfo/buildroot ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [Buildroot] [PATCH v8 0/2] board/lx2160ardb board/lx2160a-rdb new platform and newconfig 2026-11-05 15:36 ` [Buildroot] [PATCH v8 0/2] board/lx2160ardb board/lx2160a-rdb new platform and newconfig Léo DENIEUL @ 2026-11-05 15:47 ` Leo DENIEUL 0 siblings, 0 replies; 15+ messages in thread From: Leo DENIEUL @ 2026-11-05 15:47 UTC (permalink / raw) To: buildroot; +Cc: Thomas Petazzoni, Vladimir Oltean, Maxime Leroy, Vincent Jardin On Thu, Nov 05, 2026 at 04:36:29PM +0100, Léo DENIEUL wrote: > - patch 1/2 is v7 3/3 with the DEVELOPERS entries Thomas asked for > (Vladimir Oltean and myself). For the record, patch 1/2 is authored by Vladimir Oltean but was sent by me, with his From: header kept as is. Sorry for any confusion. Léo _______________________________________________ buildroot mailing list buildroot@buildroot.org https://lists.buildroot.org/mailman/listinfo/buildroot ^ permalink raw reply [flat|nested] 15+ messages in thread
* [Buildroot] [PATCH v8 1/2] board/lx2160ardb: new platform 2026-10-28 15:41 ` Vladimir Oltean 2026-11-05 15:36 ` [Buildroot] [PATCH v8 0/2] board/lx2160ardb board/lx2160a-rdb new platform and newconfig Léo DENIEUL @ 2026-11-05 15:36 ` Vladimir Oltean 2026-11-05 21:00 ` Vladimir Oltean 2026-11-05 15:37 ` [Buildroot] [PATCH v8 2/2] configs/lx2160a-rdb: new defconfig Léo DENIEUL 2 siblings, 1 reply; 15+ messages in thread From: Vladimir Oltean @ 2026-11-05 15:36 UTC (permalink / raw) To: buildroot; +Cc: Thomas Petazzoni, Vladimir Oltean, Maxime Leroy, Vincent Jardin Add Buildroot support for the NXP LX2160A-RDB (reference design board). This is configured here to boot from the SD card. To my surprise, NXP RCWs for LX2160A rev2 silicon don't have a pre-existing example for SD boot, so until one is available, include the RCW through board files. The boot uses U-Boot's bootstd framework with extlinux.conf. The DPAA2 Management Complex firmware is loaded from the filesystem during U-Boot board init. EFI boot support is disabled since we use extlinux. Signed-off-by: Vladimir Oltean <olteanv@gmail.com> Reviewed-by: Vincent Jardin <vjardin@free.fr> Tested-by: Maxime Leroy <maxime@leroys.fr> Signed-off-by: Maxime Leroy <maxime@leroys.fr> Reviewed-by: Vladimir Oltean <olteanv@gmail.com> Tested-by: Vladimir Oltean <olteanv@gmail.com> Signed-off-by: Leo DENIEUL <leo.denieul.yoshino@gmail.com> --- DEVELOPERS | 5 + board/freescale/common/env-dpaa2.txt | 7 + .../udev/rules.d/74-dpaa2-networking.rules | 29 ++++ board/freescale/lx2160ardb/extlinux.conf | 4 + board/freescale/lx2160ardb/genimage.cfg | 47 +++++++ .../arm-trusted-firmware.hash | 2 + .../patches/linux-headers/linux-headers.hash | 1 + .../lx2160ardb/patches/linux/linux.hash | 2 + .../lx2160ardb/patches/uboot/uboot.hash | 2 + board/freescale/lx2160ardb/post-build.sh | 11 ++ .../rcw_2200_750_3200_19_5_2_sd.rcw | 67 +++++++++ board/freescale/lx2160ardb/readme.txt | 129 ++++++++++++++++++ board/freescale/lx2160ardb/uboot-env.txt | 11 ++ board/freescale/lx2160ardb/uboot.config | 2 + configs/freescale_lx2160ardb_defconfig | 59 ++++++++ 15 files changed, 378 insertions(+) create mode 100644 board/freescale/common/env-dpaa2.txt create mode 100644 board/freescale/common/rootfs_overlay/etc/udev/rules.d/74-dpaa2-networking.rules create mode 100644 board/freescale/lx2160ardb/extlinux.conf create mode 100644 board/freescale/lx2160ardb/genimage.cfg create mode 100644 board/freescale/lx2160ardb/patches/arm-trusted-firmware/arm-trusted-firmware.hash create mode 120000 board/freescale/lx2160ardb/patches/linux-headers/linux-headers.hash create mode 100644 board/freescale/lx2160ardb/patches/linux/linux.hash create mode 100644 board/freescale/lx2160ardb/patches/uboot/uboot.hash create mode 100755 board/freescale/lx2160ardb/post-build.sh create mode 100644 board/freescale/lx2160ardb/rcw_2200_750_3200_19_5_2_sd.rcw create mode 100644 board/freescale/lx2160ardb/readme.txt create mode 100644 board/freescale/lx2160ardb/uboot-env.txt create mode 100644 board/freescale/lx2160ardb/uboot.config create mode 100644 configs/freescale_lx2160ardb_defconfig diff --git a/DEVELOPERS b/DEVELOPERS index 1f86c777c3..659c748db9 100644 --- a/DEVELOPERS +++ b/DEVELOPERS @@ -2175,6 +2175,9 @@ F: package/petitboot/ N: Lee Jones <lee.jones@linaro.org> F: boot/afboot-stm32/ +N: Leo Denieul <leo.denieul.yoshino@gmail.com> +F: configs/freescale_lx2160ardb_defconfig + N: Leon Anavi <leon.anavi@konsulko.com> F: board/olimex/a10_olinuxino F: configs/olimex_a10_olinuxino_lime_defconfig @@ -3499,6 +3502,8 @@ N: Vinicius Tinti <viniciustinti@gmail.com> F: package/python-thrift/ N: Vladimir Oltean <olteanv@gmail.com> +F: board/freescale/lx2160ardb +F: configs/freescale_lx2160ardb_defconfig F: package/qoriq-ddr-phy-binary/ F: package/qoriq-firmware-inphi/ F: package/qoriq-mc-binary/ diff --git a/board/freescale/common/env-dpaa2.txt b/board/freescale/common/env-dpaa2.txt new file mode 100644 index 0000000000..e60bcdeac0 --- /dev/null +++ b/board/freescale/common/env-dpaa2.txt @@ -0,0 +1,7 @@ +# DPAA2 MC firmware loading (common to all DPAA2 boards) +dpl_addr_r=0x80d00000 +dpc_addr_r=0x80e00000 +fsl_bootcmd_mcinitcmd_set=y +mc_fw_addr_r=0x80a00000 +mcinitcmd=mmc dev 0 && load mmc 0:1 $mc_fw_addr_r /boot/mc.itb && load mmc 0:1 $dpc_addr_r /boot/dpc.dtb && load mmc 0:1 $dpl_addr_r /boot/dpl.dtb && fsl_mc start mc $mc_fw_addr_r $dpc_addr_r && fsl_mc lazyapply dpl $dpl_addr_r +mcmemsize=0x70000000 diff --git a/board/freescale/common/rootfs_overlay/etc/udev/rules.d/74-dpaa2-networking.rules b/board/freescale/common/rootfs_overlay/etc/udev/rules.d/74-dpaa2-networking.rules new file mode 100644 index 0000000000..ac55225673 --- /dev/null +++ b/board/freescale/common/rootfs_overlay/etc/udev/rules.d/74-dpaa2-networking.rules @@ -0,0 +1,29 @@ +SUBSYSTEM!="net", GOTO="fsl_dpaa2_rules_end" +ACTION!="add|change|online|offline", GOTO="fsl_dpaa2_rules_end" + +# Rules that match on objects connected to DPMACs have priority, and are named +# after those DPMACs. +DRIVERS=="fsl_dpaa2_eth|fsl_dpaa2_switch", ENV{OF_FULLNAME}=="/soc/fsl-mc@80c000000/dpmacs/ethernet@1", NAME="endpmac1", GOTO="fsl_dpaa2_rules_end" +DRIVERS=="fsl_dpaa2_eth|fsl_dpaa2_switch", ENV{OF_FULLNAME}=="/soc/fsl-mc@80c000000/dpmacs/ethernet@2", NAME="endpmac2", GOTO="fsl_dpaa2_rules_end" +DRIVERS=="fsl_dpaa2_eth|fsl_dpaa2_switch", ENV{OF_FULLNAME}=="/soc/fsl-mc@80c000000/dpmacs/ethernet@3", NAME="endpmac3", GOTO="fsl_dpaa2_rules_end" +DRIVERS=="fsl_dpaa2_eth|fsl_dpaa2_switch", ENV{OF_FULLNAME}=="/soc/fsl-mc@80c000000/dpmacs/ethernet@4", NAME="endpmac4", GOTO="fsl_dpaa2_rules_end" +DRIVERS=="fsl_dpaa2_eth|fsl_dpaa2_switch", ENV{OF_FULLNAME}=="/soc/fsl-mc@80c000000/dpmacs/ethernet@5", NAME="endpmac5", GOTO="fsl_dpaa2_rules_end" +DRIVERS=="fsl_dpaa2_eth|fsl_dpaa2_switch", ENV{OF_FULLNAME}=="/soc/fsl-mc@80c000000/dpmacs/ethernet@6", NAME="endpmac6", GOTO="fsl_dpaa2_rules_end" +DRIVERS=="fsl_dpaa2_eth|fsl_dpaa2_switch", ENV{OF_FULLNAME}=="/soc/fsl-mc@80c000000/dpmacs/ethernet@7", NAME="endpmac7", GOTO="fsl_dpaa2_rules_end" +DRIVERS=="fsl_dpaa2_eth|fsl_dpaa2_switch", ENV{OF_FULLNAME}=="/soc/fsl-mc@80c000000/dpmacs/ethernet@8", NAME="endpmac8", GOTO="fsl_dpaa2_rules_end" +DRIVERS=="fsl_dpaa2_eth|fsl_dpaa2_switch", ENV{OF_FULLNAME}=="/soc/fsl-mc@80c000000/dpmacs/ethernet@9", NAME="endpmac9", GOTO="fsl_dpaa2_rules_end" +DRIVERS=="fsl_dpaa2_eth|fsl_dpaa2_switch", ENV{OF_FULLNAME}=="/soc/fsl-mc@80c000000/dpmacs/ethernet@a", NAME="endpmac10", GOTO="fsl_dpaa2_rules_end" +DRIVERS=="fsl_dpaa2_eth|fsl_dpaa2_switch", ENV{OF_FULLNAME}=="/soc/fsl-mc@80c000000/dpmacs/ethernet@11", NAME="endpmac17", GOTO="fsl_dpaa2_rules_end" +DRIVERS=="fsl_dpaa2_eth|fsl_dpaa2_switch", ENV{OF_FULLNAME}=="/soc/fsl-mc@80c000000/dpmacs/ethernet@12", NAME="endpmac18", GOTO="fsl_dpaa2_rules_end" + +# Rules that match on DPNI objects which are not connected to DPMACs, but to +# other DPNIs, DPSW ports, DPDMUX etc. Below is an example to set up a +# persistent MAC address, which can be extended beyond dpni.0. +# DRIVERS=="fsl_dpaa2_eth", DEVPATH=="/devices/platform/soc/80c000000.fsl-mc/dprc.[0-9]*/dpni.0/net/*", NAME="endpni0", PROGRAM="/sbin/ip link set %k address 00:01:02:03:04:05" + +# Rules that match on DPSW ports not connected to a DPMAC. +# Below is an example to set up a persistent MAC address, which can be extended +# beyond dpsw.0. +# DRIVERS=="fsl_dpaa2_switch", DEVPATH=="/devices/platform/soc/80c000000.fsl-mc/dprc.[0-9]*/dpsw.0/net/*", NAME="endpsw0%s{phys_port_name}", PROGRAM="/sbin/ip link set %k address 00:01:02:03:04:05" + +LABEL="fsl_dpaa2_rules_end" diff --git a/board/freescale/lx2160ardb/extlinux.conf b/board/freescale/lx2160ardb/extlinux.conf new file mode 100644 index 0000000000..58c2720252 --- /dev/null +++ b/board/freescale/lx2160ardb/extlinux.conf @@ -0,0 +1,4 @@ +label NXP LX2160A Reference Design Board + kernel /boot/Image + devicetree /boot/fsl-lx2160a-rdb.dtb + append console=ttyAMA0,115200 root=PARTUUID=%PARTUUID% rw rootwait cma=256M diff --git a/board/freescale/lx2160ardb/genimage.cfg b/board/freescale/lx2160ardb/genimage.cfg new file mode 100644 index 0000000000..f895a5ab5e --- /dev/null +++ b/board/freescale/lx2160ardb/genimage.cfg @@ -0,0 +1,47 @@ +image sdcard.img { + /* Primary GPT table needs to be moved to a region which does + * not collide with the RCW/PBI location + */ + hdimage { + partition-table-type = "gpt" + gpt-location = 6M + } + + partition rcw { + offset = 4K + in-partition-table = "no" + image = "bl2_sd.pbl" + } + + partition u-boot { + offset = 1M + in-partition-table = "no" + image = "fip.bin" + } + + partition u-boot-environment { + in-partition-table = "no" + image = "uboot-env.bin" + offset = 5M + } + + /* Offset must match PLAT_DDR_FIP_OFFSET from ATF */ + partition ddr-phy { + in-partition-table = "no" + image = "fip_ddr.bin" + offset = 8M + } + + /* Offset must match IN112525_FW_ADDR from U-Boot */ + partition 25ge-retimer-ucode { + in-partition-table = "no" + image = "in112525-phy-ucode.txt" + offset = 0x980000 + } + + partition rootfs { + bootable = "true" + image = "rootfs.ext4" + partition-uuid = %PARTUUID% + } +} diff --git a/board/freescale/lx2160ardb/patches/arm-trusted-firmware/arm-trusted-firmware.hash b/board/freescale/lx2160ardb/patches/arm-trusted-firmware/arm-trusted-firmware.hash new file mode 100644 index 0000000000..4b761bede3 --- /dev/null +++ b/board/freescale/lx2160ardb/patches/arm-trusted-firmware/arm-trusted-firmware.hash @@ -0,0 +1,2 @@ +# Locally computed +sha256 2d3f9c52e16766c290bdc0bc130d634e4c326a5b236dfb2f2ca3f0fa457e82d4 atf-lf-6.12.34-2.1.0.tar.gz diff --git a/board/freescale/lx2160ardb/patches/linux-headers/linux-headers.hash b/board/freescale/lx2160ardb/patches/linux-headers/linux-headers.hash new file mode 120000 index 0000000000..5808d92afe --- /dev/null +++ b/board/freescale/lx2160ardb/patches/linux-headers/linux-headers.hash @@ -0,0 +1 @@ +../linux/linux.hash \ No newline at end of file diff --git a/board/freescale/lx2160ardb/patches/linux/linux.hash b/board/freescale/lx2160ardb/patches/linux/linux.hash new file mode 100644 index 0000000000..f30030c86a --- /dev/null +++ b/board/freescale/lx2160ardb/patches/linux/linux.hash @@ -0,0 +1,2 @@ +# Locally computed +sha256 27a1987ca0a5802d3ebb296b8134ec66d813ad86cf2a60779b45092735bbb23b linux-lf-6.12.34-2.1.0.tar.gz diff --git a/board/freescale/lx2160ardb/patches/uboot/uboot.hash b/board/freescale/lx2160ardb/patches/uboot/uboot.hash new file mode 100644 index 0000000000..38d54d9922 --- /dev/null +++ b/board/freescale/lx2160ardb/patches/uboot/uboot.hash @@ -0,0 +1,2 @@ +# Locally computed +sha256 2f25cde388b2f83ff7a8e3afe25aafb1db48dafb0fa3bf1e4f9fef603f3b4785 u-boot-lf-6.12.34-2.1.0.tar.gz diff --git a/board/freescale/lx2160ardb/post-build.sh b/board/freescale/lx2160ardb/post-build.sh new file mode 100755 index 0000000000..4042bf9c7e --- /dev/null +++ b/board/freescale/lx2160ardb/post-build.sh @@ -0,0 +1,11 @@ +#!/bin/sh + +BOARD_DIR="$(dirname "$0")" +PARTUUID="$("$HOST_DIR/bin/uuidgen")" + +install -d "$TARGET_DIR/boot/extlinux/" +# Default DPL and DPC selections for mcinitcmd +ln -sf dpc-usxgmii.dtb "$TARGET_DIR/boot/dpc.dtb" +ln -sf dpl-eth.19.dtb "$TARGET_DIR/boot/dpl.dtb" +sed "s/%PARTUUID%/$PARTUUID/g" "$BOARD_DIR/extlinux.conf" > "$TARGET_DIR/boot/extlinux/extlinux.conf" +sed "s/%PARTUUID%/$PARTUUID/g" "$BOARD_DIR/genimage.cfg" > "$BINARIES_DIR/genimage.cfg" diff --git a/board/freescale/lx2160ardb/rcw_2200_750_3200_19_5_2_sd.rcw b/board/freescale/lx2160ardb/rcw_2200_750_3200_19_5_2_sd.rcw new file mode 100644 index 0000000000..4c4b7d9c79 --- /dev/null +++ b/board/freescale/lx2160ardb/rcw_2200_750_3200_19_5_2_sd.rcw @@ -0,0 +1,67 @@ +/* + * SerDes Protocol 1 - 19 + * SerDes Protocol 2 - 5 + * SerDes Protocol 3 - 2 + * + * Frequencies: + * Core -- 2200 MHz + * Platform -- 750 MHz + * DDR -- 3200 MT/s + */ + +#include <../lx2160asi/lx2160a.rcwi> + +SYS_PLL_RAT=15 +MEM_PLL_CFG=3 +MEM_PLL_RAT=32 +MEM2_PLL_CFG=3 +MEM2_PLL_RAT=32 +CGA_PLL1_RAT=22 +CGA_PLL2_RAT=22 +CGB_PLL1_RAT=22 +CGB_PLL2_RAT=9 +HWA_CGA_M1_CLK_SEL=1 +HWA_CGB_M1_CLK_SEL=6 +BOOT_LOC=8 +SYSCLK_FREQ=600 +IIC2_PMUX=6 +IIC3_PMUX=2 +IIC4_PMUX=2 +USB3_CLK_FSEL=39 +SRDS_PLL_PD_PLL5=1 +SRDS_PRTCL_S1=19 +SRDS_PRTCL_S2=5 +SRDS_PRTCL_S3=2 +SRDS_PLL_REF_CLK_SEL_S1=2 +SRDS_DIV_PEX_S1=1 +SRDS_DIV_PEX_S2=1 +SRDS_DIV_PEX_S3=1 + +/* Errata to write on scratch reg for validation */ +#include <../lx2160asi/scratchrw1.rcw> + +/* Boot Location Pointer */ +#include <../lx2160asi/bootlocptr_sd.rcw> + +/* Errata for SATA controller */ +#include <../lx2160asi/a010554.rcw> + +/* common PBI commands */ +#include <../lx2160asi/common.rcw> + +/* Modify FlexSPI Clock Divisor value */ +#include <../lx2160asi/flexspi_divisor_32.rcw> + +/*PCIe Errata A-009531*/ +#include <../lx2160asi/a009531_PEX3.rcw> +#include <../lx2160asi/a009531_PEX5.rcw> + +/*PCIe Errata A-008851*/ +#include <../lx2160asi/a008851_PEX3.rcw> +#include <../lx2160asi/a008851_PEX5.rcw> + +/*SerDes Errata A-050479*/ +#include <../lx2160asi/a050479.rcw> + +/* Errata A-050426 */ +#include <../lx2160asi/a050426.rcw> diff --git a/board/freescale/lx2160ardb/readme.txt b/board/freescale/lx2160ardb/readme.txt new file mode 100644 index 0000000000..6dfc3f592b --- /dev/null +++ b/board/freescale/lx2160ardb/readme.txt @@ -0,0 +1,129 @@ +************** +NXP LX2160ARDB +************** + +This file documents the Buildroot support for the LX2160A Reference Design Board. + +For more details about the board and the QorIQ Layerscape SoC, see the +following pages (notably the "LX2160A Reference Design Board Getting Started +Guide", for which this guide serves as an addition, not a replacement): + - https://www.nxp.com/design/design-center/software/qoriq-developer-resources/layerscape-lx2160a-reference-design-board:LX2160A-RDB + - https://www.nxp.com/LX2160A + +Layerscape platforms are officially supported by NXP under the Layerscape +Debian Linux SDK (LDLSDK). This uses components from Linux Factory (project +common with i.MX), but has a slower release cadence than LF. The currently used +tag is lf-6.12.34-2.1.0, which is in line with the latest LF tag. Generally, in +Buildroot, the latest Linux Factory release tag is always used, which may be +considered pre-release software, as it may contain features which are not yet +documented, and it generally undergoes less testing. + +For the software Layerscape Debian Linux SDK User Guide, see: + - https://docs.nxp.com/bundle/UG10143/page/topics/about_this_document.html + - https://www.nxp.com/docs/en/user-guide/UG10143.pdf + +The components from NXP are: + - atf (fork), lf-6.12.34-2.1.0 + - linux (fork), lf-6.12.34-2.1.0 + - qoriq-ddr-phy-binary (blob), lf-6.12.34-2.1.0 + - qoriq-firmware-inphi (blob), static commit + - qoriq-mc-binary (blob), mc_release_10.39.0 + - qoriq-mc-utils, mc_release_10.39.0 + - qoriq-rcw, lf-6.12.34-2.1.0 + - qoriq-restool, lf-6.12.34-2.1.0 + - uboot (fork), lf-6.12.34-2.1.0 + +Build +===== + +First, configure Buildroot for the LX2160ARDB board: + + make freescale_lx2160ardb_defconfig + +Build all components: + + make + +You will find in output/images/ the following files: + - bl2_sd.pbl - RCW + ATF BL2 stage + - dpc-usxgmii.dtb - the default DPC file + - dpc-warn.dtb + - dpl-2dpni.dtb + - dpl-eth.19.dtb - the default DPL file + - fip_ddr.bin - DDR PHY firmware + - fip.bin - U-Boot packaged as ATF payload + - fsl-lx2160a-rdb.dtb + - Image + - in112525-phy-ucode.txt - Firmware file for 25GbE SFP+ retimer + - mc.itb - MC firmware + - PBL.bin + - rootfs.ext2 + - rootfs.ext4 + - sdcard.img + - u-boot.bin + - uboot-env.bin + +Create a bootable SD card +========================= + +To determine the device associated to the SD card have a look in the +/proc/partitions file: + + cat /proc/partitions + +Buildroot prepares a bootable "sdcard.img" image in the output/images/ +directory, ready to be dumped on a SD card. Launch the following +command as root: + + dd if=output/images/sdcard.img of=/dev/sdX + +The SD card image can also be programmed from a live system running U-Boot: + + => setenv autoload off && tftp $load_addr sdcard.img && mmc dev 0 && mmc write $load_addr 0 0x80000 + +*** WARNING! This will destroy all the card content. Use with care! *** + +For details about the medium image layout, see the definition in +board/freescale/lx2160ardb/genimage.cfg. + +Boot the LX2160ARDB board +========================= + +To boot your newly created system: +- insert the SD card in the SD slot of the board; +- Configure the switches SW1[1:4] = 0b1000 (select SD Card boot option), + or alternatively, run "qixis_reset sd" from a U-Boot booted from a different + boot source (NOR, eMMC etc). +- put a DB9F cable into the UART1 Port and connect using a terminal + emulator at 115200 bps, 8n1; +- power on the board. + +The DPL and DPC files provided by NXP are not maximal configurations. +They only contain a static description for: +- the 40GbE QSFP+ MAC2 (which implicitly has MAC_LINK_TYPE_FIXED, because its + entry is missing from the DPC, and this means that the link state is provided + by the MC firmware) +- the 1GbE RGMII MAC17 (specified as MAC_LINK_TYPE_PHY in the DPC, which means + that the link state is provided by phylink). + +The extra interfaces routed to front panel ports are endpmac3, endpmac4, +endpmac5, endpmac6 and endpmac18. Among the more usual networking choices, one +could create individual DPNIs for each MAC: + +$ ls-addni dpmac.3 && ls-addni dpmac.4 && ls-addni dpmac.5 && ls-addni dpmac.6 && ls-addni dpmac.18 + +or a DPSW object to accelerate L2 forwarding between them: + +$ ls-addsw --num-ifs=4 --max-fdbs=4 --flooding-cfg=DPSW_FLOODING_PER_FDB \ + --broadcast-cfg=DPSW_BROADCAST_PER_FDB dpmac.3 dpmac.4 dpmac.5 dpmac.6 +$ ip link add br0 type bridge vlan_filtering 1 && ip link set br0 up +$ for eth in endpmac3 endpmac4 endpmac5 endpmac6; do \ + ip link set $eth master br0 && ip link set $eth up; done + +Once the runtime configuration is satisfactory, it can be converted back into a +permanent DPL file which can be plugged back into the build system: + +$ restool dprc generate-dpl > dpl-new.dts + +Using the device tree compiler (dtc), the new DPL can be transformed into a +.dtb file and deployed as a custom networking configuration upon the next boot. diff --git a/board/freescale/lx2160ardb/uboot-env.txt b/board/freescale/lx2160ardb/uboot-env.txt new file mode 100644 index 0000000000..89090edb32 --- /dev/null +++ b/board/freescale/lx2160ardb/uboot-env.txt @@ -0,0 +1,11 @@ +# Memory addresses for bootstd +fdt_addr_r=0x90000000 +kernel_addr_r=0x81000000 +scriptaddr=0x80000000 + +# Boot order and network +boot_targets=usb0 mmc0 mmc1 scsi0 dhcp +ethprime=DPMAC1@xgmii + +# Boot command (MC already loaded via fsl_bootcmd_mcinitcmd_set) +bootcmd=bootflow scan diff --git a/board/freescale/lx2160ardb/uboot.config b/board/freescale/lx2160ardb/uboot.config new file mode 100644 index 0000000000..e31254d62e --- /dev/null +++ b/board/freescale/lx2160ardb/uboot.config @@ -0,0 +1,2 @@ +# Disable EFI boot support - we use extlinux.conf via bootstd instead +# CONFIG_EFI_LOADER is not set diff --git a/configs/freescale_lx2160ardb_defconfig b/configs/freescale_lx2160ardb_defconfig new file mode 100644 index 0000000000..8678bb2df4 --- /dev/null +++ b/configs/freescale_lx2160ardb_defconfig @@ -0,0 +1,59 @@ +BR2_aarch64=y +BR2_cortex_a72=y +BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_6_12=y +BR2_GLOBAL_PATCH_DIR="board/freescale/lx2160ardb/patches" +BR2_DOWNLOAD_FORCE_CHECK_HASHES=y +BR2_TARGET_GENERIC_HOSTNAME="lx2160ardb" +BR2_ROOTFS_DEVICE_CREATION_DYNAMIC_EUDEV=y +BR2_TARGET_GENERIC_GETTY_PORT="ttyAMA0" +BR2_ROOTFS_OVERLAY="board/freescale/common/rootfs_overlay" +BR2_ROOTFS_POST_BUILD_SCRIPT="board/freescale/lx2160ardb/post-build.sh" +BR2_ROOTFS_POST_IMAGE_SCRIPT="support/scripts/genimage.sh" +BR2_ROOTFS_POST_SCRIPT_ARGS="-c $(BINARIES_DIR)/genimage.cfg" +BR2_LINUX_KERNEL=y +BR2_LINUX_KERNEL_CUSTOM_TARBALL=y +BR2_LINUX_KERNEL_CUSTOM_TARBALL_LOCATION="$(call github,nxp-qoriq,linux,lf-6.12.34-2.1.0)/linux-lf-6.12.34-2.1.0.tar.gz" +BR2_LINUX_KERNEL_USE_ARCH_DEFAULT_CONFIG=y +BR2_LINUX_KERNEL_CONFIG_FRAGMENT_FILES="$(LINUX_DIR)/arch/arm64/configs/lsdk.config" +BR2_LINUX_KERNEL_DTS_SUPPORT=y +BR2_LINUX_KERNEL_INTREE_DTS_NAME="freescale/fsl-lx2160a-rdb" +BR2_LINUX_KERNEL_INSTALL_TARGET=y +BR2_TARGET_ROOTFS_EXT2=y +BR2_TARGET_ROOTFS_EXT2_4=y +BR2_TARGET_ROOTFS_EXT2_SIZE="256M" +BR2_TARGET_ROOTFS_CPIO=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_TARBALL=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_TARBALL_LOCATION="$(call github,nxp-qoriq,atf,lf-6.12.34-2.1.0)/atf-lf-6.12.34-2.1.0.tar.gz" +BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM="lx2160ardb" +BR2_TARGET_ARM_TRUSTED_FIRMWARE_FIP=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE_RCW=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE_UBOOT_AS_BL33=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE_ADDITIONAL_VARIABLES="BOOT_MODE=sd" +BR2_TARGET_ARM_TRUSTED_FIRMWARE_IMAGES="fip.bin bl2_sd.pbl" +BR2_TARGET_UBOOT=y +BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y +BR2_TARGET_UBOOT_CUSTOM_TARBALL=y +BR2_TARGET_UBOOT_CUSTOM_TARBALL_LOCATION="$(call github,nxp-qoriq,u-boot,lf-6.12.34-2.1.0)/u-boot-lf-6.12.34-2.1.0.tar.gz" +BR2_TARGET_UBOOT_BOARD_DEFCONFIG="lx2160ardb_tfa" +BR2_TARGET_UBOOT_CONFIG_FRAGMENT_FILES="board/freescale/lx2160ardb/uboot.config" +BR2_TARGET_UBOOT_NEEDS_DTC=y +BR2_TARGET_UBOOT_NEEDS_GNUTLS=y +BR2_PACKAGE_HOST_GENIMAGE=y +BR2_PACKAGE_HOST_QORIQ_RCW=y +BR2_PACKAGE_HOST_QORIQ_RCW_CUSTOM_PATH="board/freescale/lx2160ardb/rcw_2200_750_3200_19_5_2_sd.rcw" +BR2_PACKAGE_HOST_UBOOT_TOOLS=y +BR2_PACKAGE_HOST_UBOOT_TOOLS_ENVIMAGE=y +# Minimal U-Boot environment for bootstd with DPAA2 MC firmware init +BR2_PACKAGE_HOST_UBOOT_TOOLS_ENVIMAGE_SOURCE="board/freescale/lx2160ardb/uboot-env.txt board/freescale/common/env-dpaa2.txt" +BR2_PACKAGE_HOST_UBOOT_TOOLS_ENVIMAGE_SIZE="0x2000" +BR2_PACKAGE_QORIQ_DDR_PHY_BINARY=y +BR2_PACKAGE_QORIQ_MC_BINARY=y +BR2_PACKAGE_QORIQ_MC_BINARY_TARGET_LX2160A=y +BR2_PACKAGE_QORIQ_MC_BINARY_TARGET_INSTALL_PATH="boot" +BR2_PACKAGE_QORIQ_MC_UTILS=y +BR2_PACKAGE_QORIQ_MC_UTILS_DPC_INTREE="lx2160a/LX2160A-RDB/dpc-usxgmii lx2160a/LX2160A-RDB/dpc-warn" +BR2_PACKAGE_QORIQ_MC_UTILS_DPL_INTREE="lx2160a/LX2160A-RDB/dpl-2dpni lx2160a/LX2160A-RDB/dpl-eth.19" +BR2_PACKAGE_QORIQ_MC_UTILS_TARGET_INSTALL_PATH="boot" +BR2_PACKAGE_QORIQ_RESTOOL=y +BR2_PACKAGE_QORIQ_FIRMWARE_INPHI=y -- 2.53.0 _______________________________________________ buildroot mailing list buildroot@buildroot.org https://lists.buildroot.org/mailman/listinfo/buildroot ^ permalink raw reply related [flat|nested] 15+ messages in thread
* Re: [Buildroot] [PATCH v8 1/2] board/lx2160ardb: new platform 2026-11-05 15:36 ` [Buildroot] [PATCH v8 1/2] board/lx2160ardb: new platform Vladimir Oltean @ 2026-11-05 21:00 ` Vladimir Oltean 2026-11-05 21:03 ` Léo DENIEUL 0 siblings, 1 reply; 15+ messages in thread From: Vladimir Oltean @ 2026-11-05 21:00 UTC (permalink / raw) To: Vladimir Oltean; +Cc: buildroot, Thomas Petazzoni, Maxime Leroy, Vincent Jardin On Thu, Nov 05, 2026 at 04:36:44PM +0100, Vladimir Oltean wrote: > Add Buildroot support for the NXP LX2160A-RDB (reference design board). > This is configured here to boot from the SD card. To my surprise, NXP > RCWs for LX2160A rev2 silicon don't have a pre-existing example for SD > boot, so until one is available, include the RCW through board files. > > The boot uses U-Boot's bootstd framework with extlinux.conf. The DPAA2 > Management Complex firmware is loaded from the filesystem during U-Boot > board init. EFI boot support is disabled since we use extlinux. > > Signed-off-by: Vladimir Oltean <olteanv@gmail.com> > Reviewed-by: Vincent Jardin <vjardin@free.fr> > Tested-by: Maxime Leroy <maxime@leroys.fr> > Signed-off-by: Maxime Leroy <maxime@leroys.fr> > Reviewed-by: Vladimir Oltean <olteanv@gmail.com> > Tested-by: Vladimir Oltean <olteanv@gmail.com> > Signed-off-by: Leo DENIEUL <leo.denieul.yoshino@gmail.com> > --- Please fix your email client, it is still sending emails as "From: Vladimir Oltean <leo.denieul.yoshino@gmail.com>". _______________________________________________ buildroot mailing list buildroot@buildroot.org https://lists.buildroot.org/mailman/listinfo/buildroot ^ permalink raw reply [flat|nested] 15+ messages in thread
* Re: [Buildroot] [PATCH v8 1/2] board/lx2160ardb: new platform 2026-11-05 21:00 ` Vladimir Oltean @ 2026-11-05 21:03 ` Léo DENIEUL 0 siblings, 0 replies; 15+ messages in thread From: Léo DENIEUL @ 2026-11-05 21:03 UTC (permalink / raw) To: Vladimir Oltean; +Cc: buildroot, Thomas Petazzoni, Maxime Leroy, Vincent Jardin [-- Attachment #1.1: Type: text/plain, Size: 1227 bytes --] Thank you, I've written to Thomas that there was an error On Thu 5 Nov 2026 at 22:00, Vladimir Oltean <olteanv@gmail.com> wrote: > On Thu, Nov 05, 2026 at 04:36:44PM +0100, Vladimir Oltean wrote: > > Add Buildroot support for the NXP LX2160A-RDB (reference design board). > > This is configured here to boot from the SD card. To my surprise, NXP > > RCWs for LX2160A rev2 silicon don't have a pre-existing example for SD > > boot, so until one is available, include the RCW through board files. > > > > The boot uses U-Boot's bootstd framework with extlinux.conf. The DPAA2 > > Management Complex firmware is loaded from the filesystem during U-Boot > > board init. EFI boot support is disabled since we use extlinux. > > > > Signed-off-by: Vladimir Oltean <olteanv@gmail.com> > > Reviewed-by: Vincent Jardin <vjardin@free.fr> > > Tested-by: Maxime Leroy <maxime@leroys.fr> > > Signed-off-by: Maxime Leroy <maxime@leroys.fr> > > Reviewed-by: Vladimir Oltean <olteanv@gmail.com> > > Tested-by: Vladimir Oltean <olteanv@gmail.com> > > Signed-off-by: Leo DENIEUL <leo.denieul.yoshino@gmail.com> > > --- > > Please fix your email client, it is still sending emails as "From: > Vladimir Oltean <leo.denieul.yoshino@gmail.com>". > [-- Attachment #1.2: Type: text/html, Size: 2183 bytes --] [-- Attachment #2: Type: text/plain, Size: 150 bytes --] _______________________________________________ buildroot mailing list buildroot@buildroot.org https://lists.buildroot.org/mailman/listinfo/buildroot ^ permalink raw reply [flat|nested] 15+ messages in thread
* [Buildroot] [PATCH v8 2/2] configs/lx2160a-rdb: new defconfig 2026-10-28 15:41 ` Vladimir Oltean 2026-11-05 15:36 ` [Buildroot] [PATCH v8 0/2] board/lx2160ardb board/lx2160a-rdb new platform and newconfig Léo DENIEUL 2026-11-05 15:36 ` [Buildroot] [PATCH v8 1/2] board/lx2160ardb: new platform Vladimir Oltean @ 2026-11-05 15:37 ` Léo DENIEUL 2 siblings, 0 replies; 15+ messages in thread From: Léo DENIEUL @ 2026-11-05 15:37 UTC (permalink / raw) To: buildroot; +Cc: Thomas Petazzoni, Vladimir Oltean, Maxime Leroy, Vincent Jardin Add a defconfig for the NXP LX2160A-RDB using upstream components instead of the NXP BSP forks used by freescale_lx2160ardb_defconfig: - TF-A v2.15.0 - U-Boot 2026.10 (lx2160ardb_tfa_defconfig) - Linux 6.18.60 (arm64 defconfig, fsl-lx2160a-rdb.dtb) This avoids depending on NXP BSP release tags, which are not updated as often as the upstream projects. The RCW, U-Boot environment and configuration fragment are shared with board/freescale/lx2160ardb/. board/freescale/lx2160a-rdb/ contains the hashes of the upstream components, its own genimage.cfg (without the retimer firmware), and the post-build script and extlinux.conf from lx2160ardb, so that the post-build script picks this genimage.cfg. Mainline U-Boot has no loader for the Inphi IN112525 retimer firmware, so qoriq-firmware-inphi is not selected and the firmware is not written to the SD card. As a consequence, the 25GbE/50GbE/100GbE ports are not functional. Tested on an LX2160ARDB: boot from SD card. Signed-off-by: Léo DENIEUL <leo.denieul.yoshino@gmail.com> --- DEVELOPERS | 2 + board/freescale/lx2160a-rdb/extlinux.conf | 1 + board/freescale/lx2160a-rdb/genimage.cfg | 40 +++++++++++++ .../arm-trusted-firmware.hash | 2 + .../patches/linux-headers/linux-headers.hash | 2 + .../lx2160a-rdb/patches/linux/linux.hash | 2 + .../lx2160a-rdb/patches/uboot/uboot.hash | 2 + board/freescale/lx2160a-rdb/post-build.sh | 11 ++++ board/freescale/lx2160a-rdb/readme.txt | 46 +++++++++++++++ configs/lx2160a-rdb_defconfig | 56 +++++++++++++++++++ 10 files changed, 164 insertions(+) create mode 120000 board/freescale/lx2160a-rdb/extlinux.conf create mode 100644 board/freescale/lx2160a-rdb/genimage.cfg create mode 100644 board/freescale/lx2160a-rdb/patches/arm-trusted-firmware/arm-trusted-firmware.hash create mode 100644 board/freescale/lx2160a-rdb/patches/linux-headers/linux-headers.hash create mode 100644 board/freescale/lx2160a-rdb/patches/linux/linux.hash create mode 100644 board/freescale/lx2160a-rdb/patches/uboot/uboot.hash create mode 100755 board/freescale/lx2160a-rdb/post-build.sh create mode 100644 board/freescale/lx2160a-rdb/readme.txt create mode 100644 configs/lx2160a-rdb_defconfig diff --git a/DEVELOPERS b/DEVELOPERS index 659c748db9..cdce895254 100644 --- a/DEVELOPERS +++ b/DEVELOPERS @@ -2176,7 +2176,9 @@ N: Lee Jones <lee.jones@linaro.org> F: boot/afboot-stm32/ N: Leo Denieul <leo.denieul.yoshino@gmail.com> +F: board/freescale/lx2160a-rdb F: configs/freescale_lx2160ardb_defconfig +F: configs/lx2160a-rdb_defconfig N: Leon Anavi <leon.anavi@konsulko.com> F: board/olimex/a10_olinuxino diff --git a/board/freescale/lx2160a-rdb/extlinux.conf b/board/freescale/lx2160a-rdb/extlinux.conf new file mode 120000 index 0000000000..bc68bcfca3 --- /dev/null +++ b/board/freescale/lx2160a-rdb/extlinux.conf @@ -0,0 +1 @@ +../lx2160ardb/extlinux.conf \ No newline at end of file diff --git a/board/freescale/lx2160a-rdb/genimage.cfg b/board/freescale/lx2160a-rdb/genimage.cfg new file mode 100644 index 0000000000..c6780e6220 --- /dev/null +++ b/board/freescale/lx2160a-rdb/genimage.cfg @@ -0,0 +1,40 @@ +image sdcard.img { + /* Primary GPT table needs to be moved to a region which does + * not collide with the RCW/PBI location + */ + hdimage { + partition-table-type = "gpt" + gpt-location = 6M + } + + partition rcw { + offset = 4K + in-partition-table = "no" + image = "bl2_sd.pbl" + } + + partition u-boot { + offset = 1M + in-partition-table = "no" + image = "fip.bin" + } + + partition u-boot-environment { + in-partition-table = "no" + image = "uboot-env.bin" + offset = 5M + } + + /* Offset must match PLAT_DDR_FIP_OFFSET from ATF */ + partition ddr-phy { + in-partition-table = "no" + image = "fip_ddr.bin" + offset = 8M + } + + partition rootfs { + bootable = "true" + image = "rootfs.ext4" + partition-uuid = %PARTUUID% + } +} diff --git a/board/freescale/lx2160a-rdb/patches/arm-trusted-firmware/arm-trusted-firmware.hash b/board/freescale/lx2160a-rdb/patches/arm-trusted-firmware/arm-trusted-firmware.hash new file mode 100644 index 0000000000..367a03c1ce --- /dev/null +++ b/board/freescale/lx2160a-rdb/patches/arm-trusted-firmware/arm-trusted-firmware.hash @@ -0,0 +1,2 @@ +# Locally computed +sha256 b807d8bf190b7c46b4260729b4bbe2f7df83cd1086edcb181d66595ae6598d23 arm-trusted-firmware-v2.15.0-git4.tar.gz diff --git a/board/freescale/lx2160a-rdb/patches/linux-headers/linux-headers.hash b/board/freescale/lx2160a-rdb/patches/linux-headers/linux-headers.hash new file mode 100644 index 0000000000..a5e2b5fc40 --- /dev/null +++ b/board/freescale/lx2160a-rdb/patches/linux-headers/linux-headers.hash @@ -0,0 +1,2 @@ +# From https://www.kernel.org/pub/linux/kernel/v6.x/sha256sums.asc +sha256 3c2f44ef6acc021a7ad444d9a2e6ec1ef488ff09368793d0004a6080f69d621e linux-6.18.60.tar.xz diff --git a/board/freescale/lx2160a-rdb/patches/linux/linux.hash b/board/freescale/lx2160a-rdb/patches/linux/linux.hash new file mode 100644 index 0000000000..a5e2b5fc40 --- /dev/null +++ b/board/freescale/lx2160a-rdb/patches/linux/linux.hash @@ -0,0 +1,2 @@ +# From https://www.kernel.org/pub/linux/kernel/v6.x/sha256sums.asc +sha256 3c2f44ef6acc021a7ad444d9a2e6ec1ef488ff09368793d0004a6080f69d621e linux-6.18.60.tar.xz diff --git a/board/freescale/lx2160a-rdb/patches/uboot/uboot.hash b/board/freescale/lx2160a-rdb/patches/uboot/uboot.hash new file mode 100644 index 0000000000..b535557b88 --- /dev/null +++ b/board/freescale/lx2160a-rdb/patches/uboot/uboot.hash @@ -0,0 +1,2 @@ +# Locally computed +sha256 3f856da3cbbc93af51ff95fde18588a348b4a26723b01d9841e999d988481015 u-boot-2026.10.tar.bz2 diff --git a/board/freescale/lx2160a-rdb/post-build.sh b/board/freescale/lx2160a-rdb/post-build.sh new file mode 100755 index 0000000000..4042bf9c7e --- /dev/null +++ b/board/freescale/lx2160a-rdb/post-build.sh @@ -0,0 +1,11 @@ +#!/bin/sh + +BOARD_DIR="$(dirname "$0")" +PARTUUID="$("$HOST_DIR/bin/uuidgen")" + +install -d "$TARGET_DIR/boot/extlinux/" +# Default DPL and DPC selections for mcinitcmd +ln -sf dpc-usxgmii.dtb "$TARGET_DIR/boot/dpc.dtb" +ln -sf dpl-eth.19.dtb "$TARGET_DIR/boot/dpl.dtb" +sed "s/%PARTUUID%/$PARTUUID/g" "$BOARD_DIR/extlinux.conf" > "$TARGET_DIR/boot/extlinux/extlinux.conf" +sed "s/%PARTUUID%/$PARTUUID/g" "$BOARD_DIR/genimage.cfg" > "$BINARIES_DIR/genimage.cfg" diff --git a/board/freescale/lx2160a-rdb/readme.txt b/board/freescale/lx2160a-rdb/readme.txt new file mode 100644 index 0000000000..f0c03a5958 --- /dev/null +++ b/board/freescale/lx2160a-rdb/readme.txt @@ -0,0 +1,46 @@ +****************************************** +NXP LX2160ARDB (upstream TF-A/U-Boot/Linux) +****************************************** + +This file documents the Buildroot support for the LX2160A Reference Design +Board, using upstream versions of TF-A, U-Boot and Linux instead of the NXP +BSP forks used by freescale_lx2160ardb_defconfig. + +The upstream components are: + - arm-trusted-firmware, v2.15.0 + - uboot, 2026.10 (lx2160ardb_tfa_defconfig) + - linux, 6.18.60 (arm64 defconfig, fsl-lx2160a-rdb.dtb) + +The board files (RCW, U-Boot environment and configuration fragment) are +shared with freescale_lx2160ardb_defconfig and live in +board/freescale/lx2160ardb/. This directory only contains what differs: +the hashes of the upstream components and the SD card layout. + +Build +===== + +First, configure Buildroot for the LX2160ARDB board: + + make lx2160a-rdb_defconfig + +Build all components: + + make + +You will find in output/images/ the same files as described in +board/freescale/lx2160ardb/readme.txt, except in112525-phy-ucode.txt. + +Create a bootable SD card and boot the board +============================================ + +The procedure is identical to freescale_lx2160ardb_defconfig, see +board/freescale/lx2160ardb/readme.txt. + +For details about the medium image layout, see the definition in +board/freescale/lx2160a-rdb/genimage.cfg. + +Known limitations +================= + +Mainline U-Boot cannot load the firmware of the Inphi IN112525 retimer, +so the 25GbE/50GbE/100GbE ports are not functional. diff --git a/configs/lx2160a-rdb_defconfig b/configs/lx2160a-rdb_defconfig new file mode 100644 index 0000000000..c261ade4af --- /dev/null +++ b/configs/lx2160a-rdb_defconfig @@ -0,0 +1,56 @@ +BR2_cortex_a72=y +BR2_PACKAGE_HOST_LINUX_HEADERS_CUSTOM_6_18=y +BR2_GLOBAL_PATCH_DIR="board/freescale/lx2160a-rdb/patches" +BR2_DOWNLOAD_FORCE_CHECK_HASHES=y +BR2_TARGET_GENERIC_HOSTNAME="lx2160ardb" +BR2_ROOTFS_DEVICE_CREATION_DYNAMIC_EUDEV=y +BR2_TARGET_GENERIC_GETTY_PORT="ttyAMA0" +BR2_ROOTFS_OVERLAY="board/freescale/common/rootfs_overlay" +BR2_ROOTFS_POST_BUILD_SCRIPT="board/freescale/lx2160a-rdb/post-build.sh" +BR2_ROOTFS_POST_IMAGE_SCRIPT="support/scripts/genimage.sh" +BR2_ROOTFS_POST_SCRIPT_ARGS="-c $(BINARIES_DIR)/genimage.cfg" +BR2_LINUX_KERNEL=y +BR2_LINUX_KERNEL_CUSTOM_VERSION=y +BR2_LINUX_KERNEL_CUSTOM_VERSION_VALUE="6.18.60" +BR2_LINUX_KERNEL_USE_ARCH_DEFAULT_CONFIG=y +BR2_LINUX_KERNEL_DTS_SUPPORT=y +BR2_LINUX_KERNEL_INTREE_DTS_NAME="freescale/fsl-lx2160a-rdb" +BR2_LINUX_KERNEL_INSTALL_TARGET=y +BR2_TARGET_ROOTFS_EXT2=y +BR2_TARGET_ROOTFS_EXT2_4=y +BR2_TARGET_ROOTFS_EXT2_SIZE="256M" +BR2_TARGET_ROOTFS_CPIO=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_VERSION=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE_CUSTOM_VERSION_VALUE="v2.15.0" +BR2_TARGET_ARM_TRUSTED_FIRMWARE_PLATFORM="lx2160ardb" +BR2_TARGET_ARM_TRUSTED_FIRMWARE_FIP=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE_RCW=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE_UBOOT_AS_BL33=y +BR2_TARGET_ARM_TRUSTED_FIRMWARE_ADDITIONAL_VARIABLES="BOOT_MODE=sd" +BR2_TARGET_ARM_TRUSTED_FIRMWARE_IMAGES="fip.bin bl2_sd.pbl" +BR2_TARGET_UBOOT=y +BR2_TARGET_UBOOT_BUILD_SYSTEM_KCONFIG=y +BR2_TARGET_UBOOT_CUSTOM_VERSION=y +BR2_TARGET_UBOOT_CUSTOM_VERSION_VALUE="2026.10" +BR2_TARGET_UBOOT_BOARD_DEFCONFIG="lx2160ardb_tfa" +BR2_TARGET_UBOOT_CONFIG_FRAGMENT_FILES="board/freescale/lx2160ardb/uboot.config" +BR2_TARGET_UBOOT_NEEDS_DTC=y +BR2_TARGET_UBOOT_NEEDS_GNUTLS=y +BR2_PACKAGE_HOST_GENIMAGE=y +BR2_PACKAGE_HOST_QORIQ_RCW=y +BR2_PACKAGE_HOST_QORIQ_RCW_CUSTOM_PATH="board/freescale/lx2160ardb/rcw_2200_750_3200_19_5_2_sd.rcw" +BR2_PACKAGE_HOST_UBOOT_TOOLS=y +BR2_PACKAGE_HOST_UBOOT_TOOLS_ENVIMAGE=y +# Minimal U-Boot environment for bootstd with DPAA2 MC firmware init +BR2_PACKAGE_HOST_UBOOT_TOOLS_ENVIMAGE_SOURCE="board/freescale/lx2160ardb/uboot-env.txt board/freescale/common/env-dpaa2.txt" +BR2_PACKAGE_HOST_UBOOT_TOOLS_ENVIMAGE_SIZE="0x2000" +BR2_PACKAGE_QORIQ_DDR_PHY_BINARY=y +BR2_PACKAGE_QORIQ_MC_BINARY=y +BR2_PACKAGE_QORIQ_MC_BINARY_TARGET_LX2160A=y +BR2_PACKAGE_QORIQ_MC_BINARY_TARGET_INSTALL_PATH="boot" +BR2_PACKAGE_QORIQ_MC_UTILS=y +BR2_PACKAGE_QORIQ_MC_UTILS_DPC_INTREE="lx2160a/LX2160A-RDB/dpc-usxgmii lx2160a/LX2160A-RDB/dpc-warn" +BR2_PACKAGE_QORIQ_MC_UTILS_DPL_INTREE="lx2160a/LX2160A-RDB/dpl-2dpni lx2160a/LX2160A-RDB/dpl-eth.19" +BR2_PACKAGE_QORIQ_MC_UTILS_TARGET_INSTALL_PATH="boot" +BR2_PACKAGE_QORIQ_RESTOOL=y -- 2.53.0 _______________________________________________ buildroot mailing list buildroot@buildroot.org https://lists.buildroot.org/mailman/listinfo/buildroot ^ permalink raw reply related [flat|nested] 15+ messages in thread
end of thread, other threads:[~2026-11-05 21:04 UTC | newest] Thread overview: 15+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2026-10-19 7:47 [Buildroot] [PATCH v7 0/3] board/lx2160ardb: new platform Léo Denieul 2026-10-19 7:48 ` [Buildroot] [PATCH v7 1/3] package/qoriq-restool: add runtime dependencies Léo DENIEUL 2026-10-25 21:24 ` Thomas Petazzoni via buildroot 2026-10-19 7:48 ` [Buildroot] [PATCH v7 2/3] package/qoriq-restool: bump to lf-6.12.34-2.1.0 Léo DENIEUL 2026-10-25 21:24 ` Thomas Petazzoni via buildroot 2026-10-19 7:48 ` [Buildroot] [PATCH v7 3/3] board/lx2160ardb: new platform Léo DENIEUL 2026-10-25 21:25 ` Thomas Petazzoni via buildroot 2026-10-26 10:15 ` Léo DENIEUL 2026-10-28 15:41 ` Vladimir Oltean 2026-11-05 15:36 ` [Buildroot] [PATCH v8 0/2] board/lx2160ardb board/lx2160a-rdb new platform and newconfig Léo DENIEUL 2026-11-05 15:47 ` Leo DENIEUL 2026-11-05 15:36 ` [Buildroot] [PATCH v8 1/2] board/lx2160ardb: new platform Vladimir Oltean 2026-11-05 21:00 ` Vladimir Oltean 2026-11-05 21:03 ` Léo DENIEUL 2026-11-05 15:37 ` [Buildroot] [PATCH v8 2/2] configs/lx2160a-rdb: new defconfig Léo DENIEUL
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.