* [BUG] e100 driver fails to initialize the hardware after kernel bootup through kexec [not found] <1042450072.1744.75.camel@aminoacin.sh.intel.com> @ 2003-01-24 6:49 ` Michael Fu 2003-01-24 14:01 ` Eric W. Biederman [not found] ` <mailman.1043391842.14884.linux-kernel2news@redhat.com> 1 sibling, 1 reply; 6+ messages in thread From: Michael Fu @ 2003-01-24 6:49 UTC (permalink / raw) To: ebiederm; +Cc: linux-kernel After kernel was bootup through kexec command, the NIC failed to initialize. The 2.5.52 kernel was patched with kexec and kexec-hwfix patch. the following was is the dmesg output: Linux version 2.5.52 (root@aminoacin) (gcc version 2.96 20000731 (Red Hat Linux 7.1 2.96-81)) #1 SMP Fri Jan 24 14:17:58 CST 2003 Video mode to be used for restore is ffff BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 00000000000a0000 (usable) BIOS-e820: 0000000000100000 - 000000000ff87000 (usable) BIOS-e820: 000000000ff87000 - 000000000ffa6000 (ACPI data) BIOS-e820: 000000000ffa6000 - 0000000010000000 (reserved) BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved) 255MB LOWMEM available. On node 0 totalpages: 65415 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 61319 pages, LIFO batch:14 HighMem zone: 0 pages, LIFO batch:1 ACPI: RSDP (v000 DELL ) @ 0x000fd730 ACPI: RSDT (v001 DELL GX400 00000.00005) @ 0x000fd744 ACPI: FADT (v001 DELL GX400 00000.00005) @ 0x000fd774 ACPI: SSDT (v001 DELL st_ex 00000.04096) @ 0xfffe7279 ACPI: BOOT (v001 DELL GX400 00000.00005) @ 0x000fd7e8 ACPI: DSDT (v001 DELL dt_ex 00000.04096) @ 0x00000000 ACPI: BIOS passes blacklist ACPI: MADT not present Building zonelist for node : 0 Kernel command line: auto ro root=/dev/hda5 No local APIC present or hardware disabled Initializing CPU#0 Detected 1993.714 MHz processor. Console: colour VGA+ 80x25 Calibrating delay loop... 3932.16 BogoMIPS Memory: 253164k/261660k available (2804k kernel code, 7792k reserved, 1539k data, 140k init, 0k highmem) Dentry cache hash table entries: 32768 (order: 6, 262144 bytes) Inode-cache hash table entries: 16384 (order: 5, 131072 bytes) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) -> /dev -> /dev/console -> /root CPU: Before vendor init, caps: 3febf9ff 00000000 00000000, vendor = 0 CPU: Trace cache: 12K uops, L1 D cache: 8K CPU: L2 cache: 256K CPU: Hyper-Threading is disabled CPU: After vendor init, caps: 3febf9ff 00000000 00000000 00000000 CPU: After generic, caps: 3febf9ff 00000000 00000000 00000000 CPU: Common caps: 3febf9ff 00000000 00000000 00000000 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU#0: Intel P4/Xeon Extended MCE MSRs (12) available CPU#0: Thermal monitoring enabled Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX CPU0: Intel(R) Pentium(R) 4 CPU 2.00GHz stepping 02 per-CPU timeslice cutoff: 731.31 usecs. task migration cache decay timeout: 1 msecs. SMP motherboard not detected. Local APIC not detected. Using dummy APIC emulation. Starting migration thread for cpu 0 CPUS done 32 Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket mtrr: v2.0 (20020519) device class 'cpu': registering device class cpu: adding driver system:cpu PCI: PCI BIOS revision 2.10 entry at 0xfc0be, last bus=2 PCI: Using configuration type 1 device class cpu: adding device CPU 0 interfaces: adding device CPU 0 BIO: pool of 256 setup, 14Kb (56 bytes/bio) biovec pool[0]: 1 bvecs: 256 entries (12 bytes) biovec pool[1]: 4 bvecs: 256 entries (48 bytes) biovec pool[2]: 16 bvecs: 256 entries (192 bytes) biovec pool[3]: 64 bvecs: 256 entries (768 bytes) biovec pool[4]: 128 bvecs: 256 entries (1536 bytes) biovec pool[5]: 256 bvecs: 256 entries (3072 bytes) ACPI: Subsystem revision 20021212 tbxface-0099 [03] Acpi_load_tables : ACPI Tables successfully acquired Parsing all Control Methods:............................................................................................................. Table [DSDT] - 297 Objects with 29 Devices 109 Methods 19 Regions Parsing all Control Methods: Table [SSDT] - 0 Objects with 0 Devices 0 Methods 0 Regions ACPI Namespace successfully loaded at root c05b2b7c evxfevnt-0063 [04] Acpi_enable : System is already in ACPI mode evgpe-0259: *** Info: GPE Block0 defined as GPE0 to GPE15 evgpe-0259: *** Info: GPE Block1 defined as GPE16 to GPE31 Executing all Device _STA and_INI methods:............................. 29 Devices found containing: 29 _STA, 3 _INI methods Completing Region/Field/Buffer/Package initialization:.................................... Initialized 13/19 Regions 0/0 Fields 10/10 Buffers 13/13 Packages (304 nodes) ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) Transparent bridge - Intel Corp. 82801BA/CA/DB PCI Br ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 *10 11 12 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 *11 12 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 9 10 11 12 15) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *9 10 11 12 15) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 9 10 11 12 15) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *9 10 11 12 15) Linux Plug and Play Support v0.93 (c) Adam Belay block request queues: 128 requests per read queue 128 requests per write queue 8 requests per batch enter congestion at 31 exit congestion at 33 SCSI subsystem driver Revision: 1.00 device class 'scsi-host': registering drivers/usb/core/usb.c: registered new driver usbfs drivers/usb/core/usb.c: registered new driver hub PCI: Using ACPI for IRQ routing PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off' SBF: Simple Boot Flag extension found and enabled. SBF: Setting boot flags 0x80 aio_setup: sizeof(struct page) = 40 Journalled Block Device driver loaded Installing knfsd (copyright (C) 1996 okir@monad.swb.de). udf: registering filesystem ACPI: Power Button (FF) [PWRF] ACPI: Processor [CPU0] (supports C1) Serial: 8250/16550 driver $Revision: 1.90 $ IRQ sharing disabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP] parport0: irq 7 detected parport0: cpp_daisy: aa5500ff(08) parport0: assign_addrs: aa5500ff(08) parport0: cpp_daisy: aa5500ff(08) parport0: assign_addrs: aa5500ff(08) pty: 256 Unix98 ptys configured lp0: using parport0 (polling). i810_rng: RNG not detected Linux agpgart interface v1.0 (c) Dave Jones agpgart: Detected Intel i850 chipset agpgart: Maximum main memory to use for agp memory: 203M agpgart: AGP aperture is 64M @ 0xf8000000 [drm] AGP 1.0 on Intel i850 @ 0xf8000000 64MB [drm] Initialized radeon 1.7.0 20020828 on minor 0 Floppy drive(s): fd0 is 1.44M FDC 0 is a National Semiconductor PC87306 Intel(R) PRO/100 Network Driver - version 2.1.24-k2 Copyright (c) 2002 Intel Corporation PCI: Enabling device 02:09.0 (0000 -> 0003) PCI: Setting latency timer of device 02:09.0 to 64 e100: selftest timeout e100: Failed to initialize, instance #0 Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ICH2: IDE controller at PCI slot 00:1f.1 ICH2: chipset revision 4 ICH2: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio hda: IC35L040AVER07-0, ATA DISK drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hdc: SAMSUNG CD-ROM SC-148C, ATAPI CD/DVD-ROM drive hdc: Disabling (U)DMA for SAMSUNG CD-ROM SC-148C ide1 at 0x170-0x177,0x376 on irq 15 hda: host protected area => 1 hda: 78165360 sectors (40021 MB) w/1916KiB Cache, CHS=77545/16/63, UDMA(100) hda: hda1 hda2 < hda5 hda6 > hdc: ATAPI 48X CD-ROM drive, 128kB Cache Uniform CD-ROM driver Revision: 3.12 end_request: I/O error, dev hdc, sector 0 scsi HBA driver <NULL> didn't set max_sectors, please fix the template scsi HBA driver Qlogic ISP 1280/12160 didn't set max_sectors, please fix the template request_module[scsi_hostadapter]: not ready request_module[scsi_hostadapter]: not ready request_module[scsi_hostadapter]: not ready Linux Kernel Card Services 3.1.22 options: [pci] [cardbus] [pm] Initializing USB Mass Storage driver... drivers/usb/core/usb.c: registered new driver usb-storage USB Mass Storage support registered. device class 'input': registering register interface 'mouse' with class 'input' mice: PS/2 mouse device common for all mice serio: i8042 AUX port at 0x60,0x64 irq 12 input: AT Set 2 keyboard on isa0060/serio0 serio: i8042 KBD port at 0x60,0x64 irq 1 Advanced Linux Sound Architecture Driver Version 0.9.0rc5 (Sun Nov 10 19:48:18 2002 UTC). request_module[snd-card-0]: not ready request_module[snd-card-1]: not ready request_module[snd-card-2]: not ready request_module[snd-card-3]: not ready request_module[snd-card-4]: not ready request_module[snd-card-5]: not ready request_module[snd-card-6]: not ready request_module[snd-card-7]: not ready PCI: Setting latency timer of device 00:1f.5 to 64 intel8x0: clocking to 41138 ALSA device list: #0: Intel 82801BA-ICH2 at 0xd800, irq 10 NET4: Linux TCP/IP 1.0 for NET4.0 IP: routing cache hash table of 1024 buckets, 16Kbytes TCP: Hash tables configured (established 8192 bind 10922) NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. ds: no socket drivers loaded! VFS: Mounted root (ext2 filesystem) readonly. Freeing unused kernel memory: 140k freed Adding 530104k swap on /dev/hda6. Priority:-1 extents:1 warning: process `update' used the obsolete bdflush system call Fix your initscripts? warning: process `update' used the obsolete bdflush system call Fix your initscripts? I doubt this is a bug in E100 actually. -- Michael Fu <michael.fu@linux.intel.com> Not speaking for Intel, opinions are my own ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [BUG] e100 driver fails to initialize the hardware after kernel bootup through kexec 2003-01-24 6:49 ` [BUG] e100 driver fails to initialize the hardware after kernel bootup through kexec Michael Fu @ 2003-01-24 14:01 ` Eric W. Biederman 2003-01-24 14:57 ` Andrey Nekrasov 0 siblings, 1 reply; 6+ messages in thread From: Eric W. Biederman @ 2003-01-24 14:01 UTC (permalink / raw) To: Michael Fu; +Cc: linux-kernel Michael Fu <michael.fu@linux.co.intel.com> writes: > After kernel was bootup through kexec command, the NIC failed to > initialize. The 2.5.52 kernel was patched with kexec and kexec-hwfix > patch. Interesting... The patch goes cleanly onto newer kernels so feel free to play with them. You are running a single cpu system so the kexec-hwfix patch should not make a difference at this point. Your interrupt routing is via ACPI interesting... > > the following was is the dmesg output: [snip] > Intel(R) PRO/100 Network Driver - version 2.1.24-k2 > Copyright (c) 2002 Intel Corporation > > > > > > > PCI: Enabling device 02:09.0 (0000 -> 0003) > PCI: Setting latency timer of device 02:09.0 to 64 > e100: selftest timeout > e100: Failed to initialize, instance #0 [snip] > I doubt this is a bug in E100 actually. Given that everything else was working correctly this is almost certainly an e100 driver or a hardware bug. On x86 everything has been working well enough that finding something that is not a hardware/driver bug as a failure case is currently quite a challenge. Q1: Is this reproducible? Q2: Is this reproducible with the eepro100 driver? You were doing the easy case of 2.5.52 to 2.5.52 I have gotten so many false positives with things working when I reboot the exact same kernel I barely consider it a valid test case any more... If it is a bug in the driver a shutdown method can be used to clean up before reboot to place the device is a quiescent state. Either that or the drivers initialization code can be enhanced to handle more strange states. I know the eepro100 driver issues a reset before playing with the card. The e100 driver is doing this in a different order, and it is dying before it resets the card so that looks like the issue to me. Doing a clean user space shutdown may also help. Though your kexecwrapper script looked like it was probably doing that o.k. Eric ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [BUG] e100 driver fails to initialize the hardware after kernel bootup through kexec 2003-01-24 14:01 ` Eric W. Biederman @ 2003-01-24 14:57 ` Andrey Nekrasov 2003-01-24 16:07 ` Jeff Garzik 0 siblings, 1 reply; 6+ messages in thread From: Andrey Nekrasov @ 2003-01-24 14:57 UTC (permalink / raw) To: Eric W. Biederman; +Cc: Michael Fu, linux-kernel Hello Eric W. Biederman, Once you wrote about "Re: [BUG] e100 driver fails to initialize the hardware after kernel bootup through kexec": > Michael Fu <michael.fu@linux.co.intel.com> writes: > > > After kernel was bootup through kexec command, the NIC failed to > > initialize. The 2.5.52 kernel was patched with kexec and kexec-hwfix > > patch. > > Interesting... The patch goes cleanly onto newer kernels so feel > free to play with them. You are running a single cpu system > so the kexec-hwfix patch should not make a difference at this point. > > Your interrupt routing is via ACPI interesting... > > > > > the following was is the dmesg output: > > [snip] > > Intel(R) PRO/100 Network Driver - version 2.1.24-k2 > > Copyright (c) 2002 Intel Corporation > > > > > > > > > > > > > > PCI: Enabling device 02:09.0 (0000 -> 0003) > > PCI: Setting latency timer of device 02:09.0 to 64 > > e100: selftest timeout > > e100: Failed to initialize, instance #0 use NIC EEPro100+ on INTEL STL2 motherboard, with "eepro100" driver - all work ok. or "e100" driver and with patch: --- drivers/net/e100/e100.h- Wed Dec 4 15:16:08 2002 +++ drivers/net/e100/e100.h Wed Dec 4 15:16:20 2002 @@ -100,7 +100,7 @@ #define E100_MAX_NIC 16 -#define E100_MAX_SCB_WAIT 100 /* Max udelays in wait_scb */ +#define E100_MAX_SCB_WAIT 5000 /* Max udelays in wait_scb */ #define E100_MAX_CU_IDLE_WAIT 50 /* Max udelays in wait_cus_idle */ /* HWI feature related constant */ all work ok. ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [BUG] e100 driver fails to initialize the hardware after kernel bootup through kexec 2003-01-24 14:57 ` Andrey Nekrasov @ 2003-01-24 16:07 ` Jeff Garzik 2003-01-26 21:56 ` Henning P. Schmiedehausen 0 siblings, 1 reply; 6+ messages in thread From: Jeff Garzik @ 2003-01-24 16:07 UTC (permalink / raw) To: Andrey Nekrasov, Eric W. Biederman, Michael Fu, linux-kernel On Fri, Jan 24, 2003 at 05:57:55PM +0300, Andrey Nekrasov wrote: > or "e100" driver and with patch: > > > --- drivers/net/e100/e100.h- Wed Dec 4 15:16:08 2002 > +++ drivers/net/e100/e100.h Wed Dec 4 15:16:20 2002 > @@ -100,7 +100,7 @@ > > #define E100_MAX_NIC 16 > > -#define E100_MAX_SCB_WAIT 100 /* Max udelays in wait_scb */ > +#define E100_MAX_SCB_WAIT 5000 /* Max udelays in wait_scb */ > #define E100_MAX_CU_IDLE_WAIT 50 /* Max udelays in wait_cus_idle */ No, don't use this patch, it's awful. The latest Marcelo tree in BitKeeper has this fixed... the right way. See the following e100 patch, which is what Intel emailed me, and what I merged into the Marcelo tree. Jeff # -------------------------------------------- # 03/01/16 scott.feldman@intel.com 1.884.23.2 # [netdrvr e100] udelay a better way # * Bug Fix: TCO workaround after hard reset of controller to wait for TCO # traffic to settle. Workaround requires issuing a CU load base command # after hard reset, followed by a wait for scb and finally a wait for # TCO traffic bit to clear. Affects 82559s and above wired to SMBus. # -------------------------------------------- # diff -Nru a/drivers/net/e100/e100_main.c b/drivers/net/e100/e100_main.c --- a/drivers/net/e100/e100_main.c Fri Jan 24 11:06:35 2003 +++ b/drivers/net/e100/e100_main.c Fri Jan 24 11:06:35 2003 @@ -196,6 +196,7 @@ char *e100_get_brand_msg(struct e100_private *); static u8 e100_pci_setup(struct pci_dev *, struct e100_private *); static u8 e100_sw_init(struct e100_private *); +static void e100_tco_walkaround(struct e100_private *); static unsigned char e100_alloc_space(struct e100_private *); static void e100_dealloc_space(struct e100_private *); static int e100_alloc_tcb_pool(struct e100_private *); @@ -213,7 +214,7 @@ static unsigned char e100_clr_cntrs(struct e100_private *); static unsigned char e100_load_microcode(struct e100_private *); -static unsigned char e100_hw_init(struct e100_private *, u32); +static unsigned char e100_hw_init(struct e100_private *); static unsigned char e100_setup_iaaddr(struct e100_private *, u8 *); static unsigned char e100_update_stats(struct e100_private *bdp); @@ -1265,7 +1266,7 @@ /* read NIC's part number */ e100_rd_pwa_no(bdp); - if (!e100_hw_init(bdp, PORT_SOFTWARE_RESET)) { + if (!e100_hw_init(bdp)) { printk(KERN_ERR "e100: hw init failed\n"); return false; } @@ -1314,10 +1315,46 @@ return 1; } +static void __devinit +e100_tco_walkaround(struct e100_private *bdp) +{ + int i; + + /* Do software reset */ + e100_sw_reset(bdp, PORT_SOFTWARE_RESET); + + /* Do a dummy LOAD CU BASE command. */ + /* This gets us out of pre-driver to post-driver. */ + e100_exec_cmplx(bdp, 0, SCB_CUC_LOAD_BASE); + + /* Wait 20 msec for reset to take effect */ + set_current_state(TASK_UNINTERRUPTIBLE); + schedule_timeout(HZ / 50); + + /* disable interrupts since they are enabled */ + /* after device reset */ + e100_disable_clear_intr(bdp); + + /* Wait for command to be cleared up to 1 sec */ + for (i=0; i<1000; i++) { + if (!readb(&bdp->scb->scb_cmd_low)) + break; + set_current_state(TASK_UNINTERRUPTIBLE); + schedule_timeout(HZ / 1000); + } + + /* Wait for TCO request bit in PMDR register to be clear */ + for (i=0; i<500; i++) { + if (!(readb(&bdp->scb->scb_ext.d101m_scb.scb_pmdr) & BIT_1)) + break; + set_current_state(TASK_UNINTERRUPTIBLE); + schedule_timeout(HZ / 1000); + } +} + /** * e100_hw_init - initialized tthe hardware * @bdp: atapter's private data struct - * @reset_cmd: s/w reset or selective reset * * This routine performs a reset on the adapter, and configures the adapter. * This includes configuring the 82557 LAN controller, validating and setting @@ -1329,13 +1366,16 @@ * false - If the adapter failed initialization */ unsigned char __devinit -e100_hw_init(struct e100_private *bdp, u32 reset_cmd) +e100_hw_init(struct e100_private *bdp) { if (!e100_phy_init(bdp)) return false; - /* Issue a software reset to the e100 */ - e100_sw_reset(bdp, reset_cmd); + e100_sw_reset(bdp, PORT_SELECTIVE_RESET); + + /* Only 82559 or above needs TCO walkaround */ + if (bdp->rev_id >= D101MA_REV_ID) + e100_tco_walkaround(bdp); /* Load the CU BASE (set to 0, because we use linear mode) */ if (!e100_wait_exec_cmplx(bdp, 0, SCB_CUC_LOAD_BASE, 0)) ^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [BUG] e100 driver fails to initialize the hardware after kernel bootup through kexec 2003-01-24 16:07 ` Jeff Garzik @ 2003-01-26 21:56 ` Henning P. Schmiedehausen 0 siblings, 0 replies; 6+ messages in thread From: Henning P. Schmiedehausen @ 2003-01-26 21:56 UTC (permalink / raw) To: linux-kernel Jeff Garzik <jgarzik@pobox.com> writes: >+ /* Wait 20 msec for reset to take effect */ >+ set_current_state(TASK_UNINTERRUPTIBLE); >+ schedule_timeout(HZ / 50); Hm. This assumes HZ=100, doesn't it? >+ /* Wait for command to be cleared up to 1 sec */ >+ for (i=0; i<1000; i++) { >+ if (!readb(&bdp->scb->scb_cmd_low)) >+ break; >+ set_current_state(TASK_UNINTERRUPTIBLE); >+ schedule_timeout(HZ / 1000); >+ } HZ = 100 -> HZ / 1000 == 0 ? This whole patch scares me. :-) Regards Henning -- Dipl.-Inf. (Univ.) Henning P. Schmiedehausen -- Geschaeftsfuehrer INTERMETA - Gesellschaft fuer Mehrwertdienste mbH hps@intermeta.de Am Schwabachgrund 22 Fon.: 09131 / 50654-0 info@intermeta.de D-91054 Buckenhof Fax.: 09131 / 50654-20 ^ permalink raw reply [flat|nested] 6+ messages in thread
[parent not found: <mailman.1043391842.14884.linux-kernel2news@redhat.com>]
* Re: [BUG] e100 driver fails to initialize the hardware after kernel bootup through kexec [not found] ` <mailman.1043391842.14884.linux-kernel2news@redhat.com> @ 2003-01-24 16:49 ` Pete Zaitcev 0 siblings, 0 replies; 6+ messages in thread From: Pete Zaitcev @ 2003-01-24 16:49 UTC (permalink / raw) To: Michael Fu; +Cc: linux-kernel, zaitcev > After kernel was bootup through kexec command, the NIC failed to > initialize. The 2.5.52 kernel was patched with kexec and kexec-hwfix > patch. > PCI: Enabling device 02:09.0 (0000 -> 0003) > PCI: Setting latency timer of device 02:09.0 to 64 > e100: selftest timeout > e100: Failed to initialize, instance #0 A very similar thing happens on my laptop. Before the shutdown, the previous driver puts the chip into D3 power state, and after reboot the pci_enable_device cannot take it out from there, because eepro refuses to wake from D3 to D0. It will go from D3 to D2 and from D2 to D0 though. Try the attached patch, please. I do not promise it will work, but it may be worth trying. -- Pete --- linux-2.5.54/drivers/net/e100/e100_main.c 2003-01-07 10:43:37.000000000 -0800 +++ linux-2.5.54-p3/drivers/net/e100/e100_main.c 2003-01-24 08:47:14.000000000 -0800 @@ -2957,8 +2957,24 @@ e100_pci_setup(struct pci_dev *pcid, struct e100_private *bdp) { struct net_device *dev = bdp->device; + int pm; + u16 pmcsr; int rc = 0; + /* + * Workaround for warm boots and pci_set_power_state which tries + * to set D0 straight out of D3. + */ + if ((pm = pci_find_capability(pcid, PCI_CAP_ID_PM)) != 0) { + pci_read_config_word(pcid, pm + PCI_PM_CTRL, &pmcsr); + if ((pmcsr & PCI_PM_CTRL_STATE_MASK) == 3) { + /* One step at a time */ + /* P3 */ printk("e100: fixing PM from 3 to 2\n"); + pci_write_config_word(pcid, pm + PCI_PM_CTRL, 2); + udelay(200); + } + } + if ((rc = pci_enable_device(pcid)) != 0) { goto err; } ^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2003-01-26 21:47 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <1042450072.1744.75.camel@aminoacin.sh.intel.com>
2003-01-24 6:49 ` [BUG] e100 driver fails to initialize the hardware after kernel bootup through kexec Michael Fu
2003-01-24 14:01 ` Eric W. Biederman
2003-01-24 14:57 ` Andrey Nekrasov
2003-01-24 16:07 ` Jeff Garzik
2003-01-26 21:56 ` Henning P. Schmiedehausen
[not found] ` <mailman.1043391842.14884.linux-kernel2news@redhat.com>
2003-01-24 16:49 ` Pete Zaitcev
This is an external index of several public inboxes, see mirroring instructions on how to clone and mirror all data and code used by this external index.