From: Embedded System <embed.sys@gmail.com>
To: bluez-users@lists.sourceforge.net
Subject: Re: [Bluez-users] Can't init device hci0 (all information included), help! Thanx a lot!!!
Date: Mon, 24 Jan 2005 11:54:23 +0800 [thread overview]
Message-ID: <c93f2a2905012319541a6c820f@mail.gmail.com> (raw)
In-Reply-To: <1106500482.9269.46.camel@pegasus>
hi, Marcel
Thanks for the info, but it still doesn't work
I have updated my kernel to 2.6.10-mh2, and with "modprobe hci_usb
isoc=0", but when I plug the usb doggle the first time, screen prints
out :
usb 1-1 : can't set config #1, error -32
usb 1-1 : khubd timed out on ep0in
and I pull out and plug it again, it prints out only the second line as:
usb 1-1 : khubd timed out on ep0in
and the outputs(/proc/bus/usb/devices, lsusb ) as follows:
1, output from /proc/bus/usb/devices
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.10-mh2 uhci_hcd
S: Product=Intel Corp. 82371AB/EB/MB PIIX4 USB
S: SerialNumber=0000:00:07.2
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 5 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=e0(unk. ) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0a12 ProdID=0001 Rev= 4.87
C:* #Ifs= 3 Cfg#= 1 Atr=c0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(unk. ) Sub=01 Prot=01 Driver=hci_usb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=(none)
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 2 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=00 Driver=(none)
2, lsusb output
......
Bus 001 Device 005: ID 0a12:0001 Cambridge Silicon Radio Ltd.
usb 1-1: lsusb timed out on ep0in
usb 1-1: lsusb timed out on ep0in
....
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 1.10
bDeviceClass 224
bDeviceSubClass 1
bDeviceProtocol 1
bMaxPacketSize0 64
idVendor 0x0a12 Cambridge Silicon Radio Ltd.
idProduct 0x0001
bcdDevice 4.87
iManufacturer 0
iProduct 0
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 193
bNumInterfaces 3
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xc0
Self Powered
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 3
bInterfaceClass 224
bInterfaceSubClass 1
bInterfaceProtocol 1
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type none
wMaxPacketSize 16
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x02 EP 2 OUT
bmAttributes 2
Transfer Type Bulk
Synch Type none
wMaxPacketSize 64
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x82 EP 2 IN
bmAttributes 2
Transfer Type Bulk
Synch Type none
wMaxPacketSize 64
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 0
bNumEndpoints 2
bInterfaceClass 224
bInterfaceSubClass 1
bInterfaceProtocol 1
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 1
Transfer Type Isochronous
Synch Type none
wMaxPacketSize 0
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type none
wMaxPacketSize 0
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 1
bNumEndpoints 2
bInterfaceClass 224
bInterfaceSubClass 1
bInterfaceProtocol 1
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 1
Transfer Type Isochronous
Synch Type none
wMaxPacketSize 9
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type none
wMaxPacketSize 9
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 2
bNumEndpoints 2
bInterfaceClass 224
bInterfaceSubClass 1
bInterfaceProtocol 1
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 1
Transfer Type Isochronous
Synch Type none
wMaxPacketSize 17
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type none
wMaxPacketSize 17
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 3
bNumEndpoints 2
bInterfaceClass 224
bInterfaceSubClass 1
bInterfaceProtocol 1
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 1
Transfer Type Isochronous
Synch Type none
wMaxPacketSize 25
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type none
wMaxPacketSize 25
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 4
bNumEndpoints 2
bInterfaceClass 224
bInterfaceSubClass 1
bInterfaceProtocol 1
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 1
Transfer Type Isochronous
Synch Type none
wMaxPacketSize 33
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type none
wMaxPacketSize 33
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 1
bAlternateSetting 5
bNumEndpoints 2
bInterfaceClass 224
bInterfaceSubClass 1
bInterfaceProtocol 1
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x03 EP 3 OUT
bmAttributes 1
Transfer Type Isochronous
Synch Type none
wMaxPacketSize 49
bInterval 1
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x83 EP 3 IN
bmAttributes 1
Transfer Type Isochronous
Synch Type none
wMaxPacketSize 49
bInterval 1
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 2
bAlternateSetting 0
bNumEndpoints 0
bInterfaceClass 254
bInterfaceSubClass 1
bInterfaceProtocol 0
iInterface 0
unknown descriptor type: 07 21 07 88 13 ff 03
Language IDs: none (cannot get min. string descriptor; got len=-1,
error=110:Connection timed out)
Best Rgds,
Andy
On Sun, 23 Jan 2005 18:14:42 +0100, Marcel Holtmann <marcel@holtmann.org> wrote:
> Hi Andy,
>
> there is no need to post this twice ;)
>
> > when I call "hciconfig hci0 up", it prints:
> > Can't init device hci0: Connection timed out (110)
> >
> > Working environment is as follows:
> > 1, Vmware workstation 5.0 + Redhat 9.0, with kernel 2.6.8.1, bluez 2.14
> > 2, Bluetooth subsystem enabled
> > 3, Billionton BlueTooth Dongle Class I USBBTC1A
> > 4, "/etc/rc.d/init.d/bluetooth start" already run
> >
> > Outputs (lspci, lsmod, /proc/bus/usb/devices/,hciconfig, dmesg)
> > 1, output from lspci
> > 00:07.2 USB Controller: Intel Corp. 82371AB/EB/MB PIIX4 USB
> >
> > 2, output from lsmod
> > Module Size Used by
> > ehci_hcd 42688 0
> > hci_usb 13184 0
> > rfcomm 38712 0
> > l2cap 24128 3 rfcomm
> > autofs 15520 0
> > ohci1394 34912 0
> > ieee1394 110384 1 ohci1394
> > parport_pc 25696 0
> > parport 40672 1 parport_pc
> > bluetooth 48292 3 hci_usb,rfcomm,l2cap
> > usbhid 24800 0
> > uhci_hcd 33160 0
> > usbcore 127540 6 ehci_hcd,hci_usb,usbhid,uhci_hcd
> >
> > 3, output from /proc/bus/usb/devices
> >
> > T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
> > B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
> > D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
> > P: Vendor=0000 ProdID=0000 Rev= 2.06
> > S: Manufacturer=Linux 2.6.8.1 uhci_hcd
> > S: Product=Intel Corp. 82371AB/EB/MB PIIX4 USB
> > S: SerialNumber=0000:00:07.2
> > C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA
> > I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
> > E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
> >
> > T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
> > D: Ver= 1.10 Cls=e0(unk. ) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
> > P: Vendor=0a12 ProdID=0001 Rev= 4.87
> > C:* #Ifs= 3 Cfg#= 1 Atr=c0 MxPwr= 0mA
> > I: If#= 0 Alt= 0 #EPs= 3 Cls=e0(unk. ) Sub=01 Prot=01 Driver=hci_usb
> > E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
> > E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
> > E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
> > I: If#= 1 Alt= 0 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=hci_usb
> > E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
> > E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
> > I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=hci_usb
> > E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
> > E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
> > I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=hci_usb
> > E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
> > E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
> > I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=hci_usb
> > E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
> > E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
> > I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=hci_usb
> > E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
> > E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
> > I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(unk. ) Sub=01 Prot=01 Driver=hci_usb
> > E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
> > E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
> > I: If#= 2 Alt= 0 #EPs= 0 Cls=fe(app. ) Sub=01 Prot=00 Driver=(none)
> >
> > 4, output from hciconfig
> > hci0: Type: USB
> > BD Address: 00:00:00:00:00:00 ACL MTU: 0:0 SCO MTU: 0:0
> > DOWN
> > RX bytes:0 acl:0 sco:0 events:0 errors:0
> > TX bytes:0 acl:0 sco:0 commands:0 errors:0
> > Features: 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
> > Packet type: DM1 DH1 HV1
> > Link policy:
> > Link mode: SLAVE ACCEPT
> >
> > 8, output from dmesg
> > uhci_hcd 0000:00:07.2: suspend_hc
> > uhci_hcd 0000:00:07.2: wakeup_hc
> > uhci_hcd 0000:00:07.2: port 1 portsc 0083
> > hub 1-0:1.0: port 1, status 0101, change 0001, 12 Mb/s
> > hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x101
> > usb 1-1: new full speed USB device using address 3
> > usb 1-1: skipped 1 descriptor after interface
> > usb 1-1: new device strings: Mfr=0, Product=0, SerialNumber=0
> > usb 1-1: hotplug
> > usb 1-1: adding 1-1:1.0 (config #1, interface 0)
> > usb 1-1:1.0: hotplug
> > hci_usb 1-1:1.0: usb_probe_interface
> > hci_usb 1-1:1.0: usb_probe_interface - got id
> > usb 1-1: adding 1-1:1.1 (config #1, interface 1)
> > usb 1-1:1.1: hotplug
> > usb 1-1: adding 1-1:1.2 (config #1, interface 2)
> > usb 1-1:1.2: hotplug
> > hci_usb 1-1:1.2: usb_probe_interface
> > hci_usb 1-1:1.2: usb_probe_interface - got id
> >
> >
> > I really appreciate your kindly help and your time! if you need any
> > further information
> > please let me know, thanx again!
> >
> > Is it a kernel problem? Bluez bug? Configuration Problem? Vmware
> > Restrictions? or what else?
>
> maybe the ISOC transfers are not working perfect within VMware. You can
> disable them with isoc=0 when loading hci_usb. And you should try a
> newer kernel. Check out 2.6.10-mh2 or 2.6.11-rc2.
>
> Regards
>
> Marcel
>
> -------------------------------------------------------
> This SF.Net email is sponsored by: IntelliVIEW -- Interactive Reporting
> Tool for open source databases. Create drag-&-drop reports. Save time
> by over 75%! Publish reports on the web. Export to DOC, XLS, RTF, etc.
> Download a FREE copy at http://www.intelliview.com/go/osdn_nl
> _______________________________________________
> Bluez-users mailing list
> Bluez-users@lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/bluez-users
>
-------------------------------------------------------
This SF.Net email is sponsored by: IntelliVIEW -- Interactive Reporting
Tool for open source databases. Create drag-&-drop reports. Save time
by over 75%! Publish reports on the web. Export to DOC, XLS, RTF, etc.
Download a FREE copy at http://www.intelliview.com/go/osdn_nl
_______________________________________________
Bluez-users mailing list
Bluez-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/bluez-users
next prev parent reply other threads:[~2005-01-24 3:54 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2005-01-23 10:10 [Bluez-users] Can't init device hci0 (all information included), help! Thanx a lot!!! Embedded System
2005-01-23 17:14 ` Marcel Holtmann
2005-01-24 3:54 ` Embedded System [this message]
2005-01-24 8:19 ` Michal Semler
2005-01-24 10:05 ` Embedded System
2005-01-24 12:22 ` Marcel Holtmann
2005-01-25 15:23 ` Embedded System
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=c93f2a2905012319541a6c820f@mail.gmail.com \
--to=embed.sys@gmail.com \
--cc=bluez-users@lists.sourceforge.net \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.