* [U-Boot] [PATCH v3 3/3] XPedite5370 board support
2008-11-26 17:12 ` [U-Boot] [PATCH v3 2/3] Add support for Maxim's DS4510 I2C device Peter Tyser
@ 2008-11-26 17:12 ` Peter Tyser
0 siblings, 0 replies; 4+ messages in thread
From: Peter Tyser @ 2008-11-26 17:12 UTC (permalink / raw)
To: u-boot
Initial support for Extreme Engineering Solutions XPedite5370 -
a MPC8572-based 3U VPX single board computer with a PMC/XMC
site.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
---
MAINTAINERS | 3 +
MAKEALL | 1 +
Makefile | 3 +
board/xes/common/Makefile | 56 ++++
board/xes/common/fsl_8572_clk.c | 51 +++
board/xes/common/fsl_85xx_ddr.c | 93 ++++++
board/xes/common/fsl_85xx_pci.c | 265 ++++++++++++++++
board/xes/xpedite5370/Makefile | 45 +++
board/xes/xpedite5370/config.mk | 35 ++
board/xes/xpedite5370/ddr.c | 270 ++++++++++++++++
board/xes/xpedite5370/law.c | 54 ++++
board/xes/xpedite5370/tlb.c | 94 ++++++
board/xes/xpedite5370/u-boot.lds | 145 +++++++++
board/xes/xpedite5370/xpedite5370.c | 128 ++++++++
include/configs/XPEDITE5370.h | 590 +++++++++++++++++++++++++++++++++++
15 files changed, 1833 insertions(+), 0 deletions(-)
create mode 100644 board/xes/common/Makefile
create mode 100644 board/xes/common/fsl_8572_clk.c
create mode 100644 board/xes/common/fsl_85xx_ddr.c
create mode 100644 board/xes/common/fsl_85xx_pci.c
create mode 100644 board/xes/xpedite5370/Makefile
create mode 100644 board/xes/xpedite5370/config.mk
create mode 100644 board/xes/xpedite5370/ddr.c
create mode 100644 board/xes/xpedite5370/law.c
create mode 100644 board/xes/xpedite5370/tlb.c
create mode 100644 board/xes/xpedite5370/u-boot.lds
create mode 100644 board/xes/xpedite5370/xpedite5370.c
create mode 100644 include/configs/XPEDITE5370.h
diff --git a/MAINTAINERS b/MAINTAINERS
index 127604b..ee98824 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -411,6 +411,9 @@ Rune Torgersen <runet@innovsys.com>
MPC8266ADS MPC8266
+Peter Tyser <ptyser@xes-inc.com>
+
+ XPEDITE5370 MPC8572
David Updegraff <dave@cray.com>
diff --git a/MAKEALL b/MAKEALL
index dbed268..1328514 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -376,6 +376,7 @@ LIST_85xx=" \
TQM8548 \
TQM8555 \
TQM8560 \
+ XPEDITE5370 \
"
#########################################################################
diff --git a/Makefile b/Makefile
index 0c5dd61..ae3ec22 100644
--- a/Makefile
+++ b/Makefile
@@ -2454,6 +2454,9 @@ TQM8560_config: unconfig
echo "#define CONFIG_BOARDNAME \"TQM$${CTYPE}\"">>$(obj)include/config.h;
@$(MKCONFIG) -a TQM85xx ppc mpc85xx tqm85xx tqc
+XPEDITE5370_config: unconfig
+ @$(MKCONFIG) $(@:_config=) ppc mpc85xx xpedite5370 xes
+
#########################################################################
## MPC86xx Systems
#########################################################################
diff --git a/board/xes/common/Makefile b/board/xes/common/Makefile
new file mode 100644
index 0000000..c5cd633
--- /dev/null
+++ b/board/xes/common/Makefile
@@ -0,0 +1,56 @@
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+ifneq ($(OBJTREE),$(SRCTREE))
+$(shell mkdir -p $(obj)board/$(VENDOR)/common)
+endif
+
+LIB = $(obj)lib$(VENDOR).a
+
+COBJS-$(CONFIG_MPC8572) += fsl_8572_clk.o
+COBJS-$(CONFIG_MPC85xx) += fsl_85xx_ddr.o
+COBJS-$(CONFIG_FSL_PCI_INIT) += fsl_85xx_pci.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS-y:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS-y))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak $(obj).depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/xes/common/fsl_8572_clk.c b/board/xes/common/fsl_8572_clk.c
new file mode 100644
index 0000000..f5df2da
--- /dev/null
+++ b/board/xes/common/fsl_8572_clk.c
@@ -0,0 +1,51 @@
+/*
+ * Copyright 2008 Extreme Engineering Solutions, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+
+/*
+ * Return SYSCLK input frequency - 50 MHz or 66 MHz depending on POR config
+ */
+unsigned long get_board_sys_clk(ulong dummy)
+{
+ volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ u32 gpporcr = gur->gpporcr;
+
+ if (gpporcr & 0x10000)
+ return 66666666;
+ else
+ return 50000000;
+}
+
+/*
+ * Return DDR input clock - synchronous with SYSCLK or 66 MHz
+ */
+unsigned long get_board_ddr_clk(ulong dummy)
+{
+ volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ u32 ddr_ratio = ((gur->porpllsr) & 0x00003e00) >> 9;
+
+ if (ddr_ratio == 0x7)
+ return get_board_sys_clk(dummy);
+
+ return 66666666;
+}
diff --git a/board/xes/common/fsl_85xx_ddr.c b/board/xes/common/fsl_85xx_ddr.c
new file mode 100644
index 0000000..30b4767
--- /dev/null
+++ b/board/xes/common/fsl_85xx_ddr.c
@@ -0,0 +1,93 @@
+/*
+ * Copyright 2008 Extreme Engineering Solutions, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/mmu.h>
+
+#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
+extern void ddr_enable_ecc(unsigned int dram_size);
+#endif
+
+phys_size_t initdram(int board_type)
+{
+ phys_size_t dram_size = fsl_ddr_sdram();
+
+ dram_size = setup_ddr_tlbs(dram_size / 0x100000);
+
+ dram_size *= 0x100000;
+
+#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
+ /* Initialize and enable DDR ECC */
+ ddr_enable_ecc(dram_size);
+#endif
+
+ return dram_size;
+}
+
+#if defined(CONFIG_DDR_ECC) || (CONFIG_NUM_DDR_CONTROLLERS > 1)
+void board_add_ram_info(int use_default)
+{
+#if (CONFIG_NUM_DDR_CONTROLLERS > 1)
+ volatile ccsr_ddr_t *ddr1 = (void *)(CONFIG_SYS_MPC85xx_DDR_ADDR);
+#endif
+
+ puts(" (");
+
+#if (CONFIG_NUM_DDR_CONTROLLERS > 1)
+ /* Print interleaving information */
+ if (ddr1->cs0_config & 0x20000000) {
+ switch ((ddr1->cs0_config >> 24) & 0xf) {
+ case 0:
+ puts("cache line");
+ break;
+ case 1:
+ puts("page");
+ break;
+ case 2:
+ puts("bank");
+ break;
+ case 3:
+ puts("super-bank");
+ break;
+ default:
+ puts("invalid");
+ break;
+ }
+ } else {
+ puts("no");
+ }
+
+ puts(" interleaving");
+#endif
+
+#if (CONFIG_NUM_DDR_CONTROLLERS > 1) && defined(CONFIG_DDR_ECC)
+ puts(", ");
+#endif
+
+#if defined(CONFIG_DDR_ECC)
+ puts("ECC enabled");
+#endif
+
+ puts(")");
+}
+#endif /* CONFIG_DDR_ECC || CONFIG_NUM_DDR_CONTROLLERS > 1 */
diff --git a/board/xes/common/fsl_85xx_pci.c b/board/xes/common/fsl_85xx_pci.c
new file mode 100644
index 0000000..b604bcc
--- /dev/null
+++ b/board/xes/common/fsl_85xx_pci.c
@@ -0,0 +1,265 @@
+/*
+ * Copyright 2008 Extreme Engineering Solutions, Inc.
+ * Copyright 2007-2008 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <pci.h>
+#include <asm/immap_85xx.h>
+#include <asm/immap_fsl_pci.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+
+extern int fsl_pci_setup_inbound_windows(struct pci_region *r);
+extern void fsl_pci_init(struct pci_controller *hose);
+
+int first_free_busno = 0;
+
+#ifdef CONFIG_PCIE1
+static struct pci_controller pcie1_hose;
+#endif
+#ifdef CONFIG_PCIE2
+static struct pci_controller pcie2_hose;
+#endif
+#ifdef CONFIG_PCIE3
+static struct pci_controller pcie3_hose;
+#endif
+
+/* Correlate host/agent POR bits to usable info. Table 4-14 */
+struct host_agent_cfg_t {
+ uchar pcie_root[3];
+ uchar rio_host;
+} host_agent_cfg[8] = {
+ {{0, 0, 0}, 0},
+ {{0, 1, 1}, 1},
+ {{1, 0, 1}, 0},
+ {{1, 1, 0}, 1},
+ {{0, 0, 1}, 0},
+ {{0, 1, 0}, 1},
+ {{1, 0, 0}, 0},
+ {{1, 1, 1}, 1}
+};
+
+/* Correlate port width POR bits to usable info. Table 4-15 */
+struct io_port_cfg_t {
+ uchar pcie_width[3];
+ uchar rio_width;
+} io_port_cfg[16] = {
+ {{0, 0, 0}, 0},
+ {{0, 0, 0}, 0},
+ {{4, 0, 0}, 0},
+ {{4, 4, 0}, 0},
+ {{0, 0, 0}, 0},
+ {{0, 0, 0}, 0},
+ {{0, 0, 0}, 4},
+ {{4, 2, 2}, 0},
+ {{0, 0, 0}, 0},
+ {{0, 0, 0}, 0},
+ {{0, 0, 0}, 0},
+ {{4, 0, 0}, 4},
+ {{4, 0, 0}, 4},
+ {{0, 0, 0}, 4},
+ {{0, 0, 0}, 4},
+ {{8, 0, 0}, 0},
+};
+
+void pci_init_board(void)
+{
+ struct pci_controller *hose;
+ volatile ccsr_fsl_pci_t *pci;
+ int width;
+ int host;
+ volatile ccsr_gur_t *gur = (void *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
+ uint devdisr = gur->devdisr;
+ uint io_sel = (gur->pordevsr & MPC85xx_PORDEVSR_IO_SEL) >> 19;
+ uint host_agent = (gur->porbmsr & MPC85xx_PORBMSR_HA) >> 16;
+ struct pci_region *r;
+
+ debug(" pci_init_board: devdisr=%x, io_sel=%x, host_agent=%x\n",
+ devdisr, io_sel, host_agent);
+
+#ifdef CONFIG_PCIE1
+ pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE1_ADDR;
+ hose = &pcie1_hose;
+ host = host_agent_cfg[host_agent].pcie_root[0];
+ width = io_port_cfg[io_sel].pcie_width[0];
+ r = hose->regions;
+
+ if (width && !(devdisr & MPC85xx_DEVDISR_PCIE)) {
+ printf("\n PCIE1 connected as %s (x%d)",
+ host ? "Root Complex" : "End Point", width);
+ if (pci->pme_msg_det) {
+ pci->pme_msg_det = 0xffffffff;
+ debug(" with errors. Clearing. Now 0x%08x",
+ pci->pme_msg_det);
+ }
+ printf("\n");
+
+ /* inbound */
+ r += fsl_pci_setup_inbound_windows(r);
+
+ /* outbound memory */
+ pci_set_region(r++,
+ CONFIG_SYS_PCIE1_MEM_BASE,
+ CONFIG_SYS_PCIE1_MEM_PHYS,
+ CONFIG_SYS_PCIE1_MEM_SIZE,
+ PCI_REGION_MEM);
+
+ /* outbound io */
+ pci_set_region(r++,
+ CONFIG_SYS_PCIE1_IO_BASE,
+ CONFIG_SYS_PCIE1_IO_PHYS,
+ CONFIG_SYS_PCIE1_IO_SIZE,
+ PCI_REGION_IO);
+
+ hose->region_count = r - hose->regions;
+
+ hose->first_busno = first_free_busno;
+ pci_setup_indirect(hose, (int)&pci->cfg_addr,
+ (int) &pci->cfg_data);
+
+ fsl_pci_init(hose);
+
+ first_free_busno = hose->last_busno+1;
+ printf(" PCIE1 on bus %02x - %02x\n",
+ hose->first_busno, hose->last_busno);
+ }
+#else
+ gur->devdisr |= MPC85xx_DEVDISR_PCIE; /* disable */
+#endif /* CONFIG_PCIE1 */
+
+#ifdef CONFIG_PCIE2
+ pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE2_ADDR;
+ hose = &pcie2_hose;
+ host = host_agent_cfg[host_agent].pcie_root[1];
+ width = io_port_cfg[io_sel].pcie_width[1];
+ r = hose->regions;
+
+ if (width && !(devdisr & MPC85xx_DEVDISR_PCIE2)) {
+ printf("\n PCIE2 connected as %s (x%d)",
+ host ? "Root Complex" : "End Point", width);
+ if (pci->pme_msg_det) {
+ pci->pme_msg_det = 0xffffffff;
+ debug(" with errors. Clearing. Now 0x%08x",
+ pci->pme_msg_det);
+ }
+ printf("\n");
+
+ /* inbound */
+ r += fsl_pci_setup_inbound_windows(r);
+
+ /* outbound memory */
+ pci_set_region(r++,
+ CONFIG_SYS_PCIE2_MEM_BASE,
+ CONFIG_SYS_PCIE2_MEM_PHYS,
+ CONFIG_SYS_PCIE2_MEM_SIZE,
+ PCI_REGION_MEM);
+
+ /* outbound io */
+ pci_set_region(r++,
+ CONFIG_SYS_PCIE2_IO_BASE,
+ CONFIG_SYS_PCIE2_IO_PHYS,
+ CONFIG_SYS_PCIE2_IO_SIZE,
+ PCI_REGION_IO);
+
+ hose->region_count = r - hose->regions;
+
+ hose->first_busno = first_free_busno;
+ pci_setup_indirect(hose, (int)&pci->cfg_addr,
+ (int)&pci->cfg_data);
+
+ fsl_pci_init(hose);
+ first_free_busno = hose->last_busno+1;
+ printf(" PCIE2 on bus %02x - %02x\n",
+ hose->first_busno, hose->last_busno);
+
+ }
+#else
+ gur->devdisr |= MPC85xx_DEVDISR_PCIE1; /* disable */
+#endif /* CONFIG_PCIE2 */
+
+#ifdef CONFIG_PCIE3
+ pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE3_ADDR;
+ hose = &pcie3_hose;
+ host = host_agent_cfg[host_agent].pcie_root[2];
+ width = io_port_cfg[io_sel].pcie_width[2];
+ r = hose->regions;
+
+ if (width && !(devdisr & MPC85xx_DEVDISR_PCIE3)) {
+ printf("\n PCIE3 connected as %s (x%d)",
+ host ? "Root Complex" : "End Point", width);
+ if (pci->pme_msg_det) {
+ pci->pme_msg_det = 0xffffffff;
+ debug(" with errors. Clearing. Now 0x%08x",
+ pci->pme_msg_det);
+ }
+ printf("\n");
+
+ /* inbound */
+ r += fsl_pci_setup_inbound_windows(r);
+
+ /* outbound memory */
+ pci_set_region(r++,
+ CONFIG_SYS_PCIE3_MEM_BASE,
+ CONFIG_SYS_PCIE3_MEM_PHYS,
+ CONFIG_SYS_PCIE3_MEM_SIZE,
+ PCI_REGION_MEM);
+
+ /* outbound io */
+ pci_set_region(r++,
+ CONFIG_SYS_PCIE3_IO_BASE,
+ CONFIG_SYS_PCIE3_IO_PHYS,
+ CONFIG_SYS_PCIE3_IO_SIZE,
+ PCI_REGION_IO);
+
+ hose->region_count = r - hose->regions;
+
+ hose->first_busno = first_free_busno;
+ pci_setup_indirect(hose, (int)&pci->cfg_addr,
+ (int)&pci->cfg_data);
+
+ fsl_pci_init(hose);
+ first_free_busno = hose->last_busno+1;
+ printf(" PCIE3 on bus %02x - %02x\n",
+ hose->first_busno, hose->last_busno);
+ }
+#else
+ gur->devdisr |= MPC85xx_DEVDISR_PCIE2; /* disable */
+#endif /* CONFIG_PCIE3 */
+}
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+extern void ft_fsl_pci_setup(void *blob, const char *pci_alias,
+ struct pci_controller *hose);
+
+void ft_board_pci_setup(void *blob, bd_t *bd)
+{
+#ifdef CONFIG_PCIE1
+ ft_fsl_pci_setup(blob, "pci2", &pcie1_hose);
+#endif
+#ifdef CONFIG_PCIE2
+ ft_fsl_pci_setup(blob, "pci1", &pcie2_hose);
+#endif
+#ifdef CONFIG_PCIE3
+ ft_fsl_pci_setup(blob, "pci0", &pcie3_hose);
+#endif
+}
+#endif /* CONFIG_OF_BOARD_SETUP */
diff --git a/board/xes/xpedite5370/Makefile b/board/xes/xpedite5370/Makefile
new file mode 100644
index 0000000..919397c
--- /dev/null
+++ b/board/xes/xpedite5370/Makefile
@@ -0,0 +1,45 @@
+#
+# Copyright 2008 Extreme Engineering Solutions, Inc.
+# Copyright 2007 Freescale Semiconductor, Inc.
+# (C) Copyright 2001-2006
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS-y += $(BOARD).o
+COBJS-y += ddr.o
+COBJS-y += law.o
+COBJS-y += tlb.o
+
+SRCS := $(SOBJS-y:.o=.S) $(COBJS-y:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS-y))
+SOBJS := $(addprefix $(obj),$(SOBJS-y))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+clean:
+ rm -f $(OBJS) $(SOBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/xes/xpedite5370/config.mk b/board/xes/xpedite5370/config.mk
new file mode 100644
index 0000000..39469b2
--- /dev/null
+++ b/board/xes/xpedite5370/config.mk
@@ -0,0 +1,35 @@
+#
+# Copyright 2008 Extreme Engineering Solutions, Inc.
+# Copyright 2007-2008 Freescale Semiconductor, Inc.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+#
+# xpedite5370 board
+#
+ifndef TEXT_BASE
+TEXT_BASE = 0xfff80000
+endif
+
+PLATFORM_RELFLAGS += -mrelocatable
+
+PLATFORM_CPPFLAGS += -DCONFIG_E500=1
+PLATFORM_CPPFLAGS += -DCONFIG_MPC85xx=1
+PLATFORM_CPPFLAGS += -DCONFIG_MPC8572=1
diff --git a/board/xes/xpedite5370/ddr.c b/board/xes/xpedite5370/ddr.c
new file mode 100644
index 0000000..fd1d43b
--- /dev/null
+++ b/board/xes/xpedite5370/ddr.c
@@ -0,0 +1,270 @@
+/*
+ * Copyright 2008 Extreme Engineering Solutions, Inc.
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <i2c.h>
+
+#include <asm/fsl_ddr_sdram.h>
+#include <asm/fsl_ddr_dimm_params.h>
+
+static void get_spd(ddr2_spd_eeprom_t *spd, unsigned char i2c_address)
+{
+ i2c_read(i2c_address, SPD_EEPROM_OFFSET, 2, (uchar *)spd,
+ sizeof(ddr2_spd_eeprom_t));
+}
+
+unsigned int fsl_ddr_get_mem_data_rate(void)
+{
+ return get_ddr_freq(0);
+}
+
+void fsl_ddr_get_spd(ddr2_spd_eeprom_t *ctrl_dimms_spd,
+ unsigned int ctrl_num)
+{
+ unsigned int i;
+ unsigned int i2c_address = 0;
+
+ for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
+ if (ctrl_num == 0)
+ i2c_address = SPD_EEPROM_ADDRESS1;
+ if (ctrl_num == 1)
+ i2c_address = SPD_EEPROM_ADDRESS2;
+ get_spd(&(ctrl_dimms_spd[i]), i2c_address);
+ }
+}
+
+/*
+ * There are four board-specific SDRAM timing parameters which must be
+ * calculated based on the particular PCB artwork. These are:
+ * 1.) CPO (Read Capture Delay)
+ * - TIMING_CFG_2 register
+ * Source: Calculation based on board trace lengths and
+ * chip-specific internal delays.
+ * 2.) WR_DATA_DELAY (Write Command to Data Strobe Delay)
+ * - TIMING_CFG_2 register
+ * Source: Calculation based on board trace lengths.
+ * Unless clock and DQ lanes are very different
+ * lengths (>2"), this should be set to the nominal value
+ * of 1/2 clock delay.
+ * 3.) CLK_ADJUST (Clock and Addr/Cmd alignment control)
+ * - DDR_SDRAM_CLK_CNTL register
+ * Source: Signal Integrity Simulations
+ * 4.) 2T Timing on Addr/Ctl
+ * - TIMING_CFG_2 register
+ * Source: Signal Integrity Simulations
+ * Usually only needed with heavy load/very high speed (>DDR2-800)
+ *
+ * ====== XPedite5370 DDR2-600 read delay calculations ======
+ *
+ * See Freescale's App Note AN2583 as refrence. This document also
+ * contains the chip-specific delays for 8548E, 8572, etc.
+ *
+ * For MPC8572E
+ * Minimum chip delay (Ch 0): 1.372ns
+ * Maximum chip delay (Ch 0): 2.914ns
+ * Minimum chip delay (Ch 1): 1.220ns
+ * Maximum chip delay (Ch 1): 2.595ns
+ *
+ * CLK adjust = 5 (from simulations) = 5/8* 3.33ns = 2080ps
+ *
+ * Minimum delay calc (Ch 0):
+ * clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly
+ * 2.3" * 180 - 400ps + 1.9" * 180 + 2080ps + 1372ps
+ * = 3808ps
+ * = 3.808ns
+ *
+ * Maximum delay calc (Ch 0):
+ * clock prop + dram skew + max dqs prop delay + clk_adjust + max chip dly
+ * 2.3" * 180 + 400ps + 2.4" * 180 + 2080ps + 2914ps
+ * = 6240ps
+ * = 6.240ns
+ *
+ * Minimum delay calc (Ch 1):
+ * clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly
+ * 1.46" * 180- 400ps + 0.7" * 180 + 2080ps + 1220ps
+ * = 3288ps
+ * = 3.288ns
+ *
+ * Maximum delay calc (Ch 1):
+ * clock prop + dram skew + max dqs prop delay + clk_adjust + min chip dly
+ * 1.46" * 180+ 400ps + 1.1" * 180 + 2080ps + 2595ps
+ * = 5536ps
+ * = 5.536ns
+ *
+ * Ch.0: 3.808ns to 6.240ns additional delay needed (pick 5ns as target)
+ * This is 1.5 clock cycles, pick CPO = READ_LAT + 3/2 (0x8)
+ * Ch.1: 3.288ns to 5.536ns additional delay needed (pick 4.4ns as target)
+ * This is 1.32 clock cycles, pick CPO = READ_LAT + 5/4 (0x7)
+ *
+ *
+ * ====== XPedite5370 DDR2-800 read delay calculations ======
+ *
+ * See Freescale's App Note AN2583 as refrence. This document also
+ * contains the chip-specific delays for 8548E, 8572, etc.
+ *
+ * For MPC8572E
+ * Minimum chip delay (Ch 0): 1.372ns
+ * Maximum chip delay (Ch 0): 2.914ns
+ * Minimum chip delay (Ch 1): 1.220ns
+ * Maximum chip delay (Ch 1): 2.595ns
+ *
+ * CLK adjust = 5 (from simulations) = 5/8* 2.5ns = 1563ps
+ *
+ * Minimum delay calc (Ch 0):
+ * clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly
+ * 2.3" * 180 - 350ps + 1.9" * 180 + 1563ps + 1372ps
+ * = 3341ps
+ * = 3.341ns
+ *
+ * Maximum delay calc (Ch 0):
+ * clock prop + dram skew + max dqs prop delay + clk_adjust + max chip dly
+ * 2.3" * 180 + 350ps + 2.4" * 180 + 1563ps + 2914ps
+ * = 5673ps
+ * = 5.673ns
+ *
+ * Minimum delay calc (Ch 1):
+ * clock prop - dram skew + min dqs prop delay + clk_adjust + min chip dly
+ * 1.46" * 180- 350ps + 0.7" * 180 + 1563ps + 1220ps
+ * = 2822ps
+ * = 2.822ns
+ *
+ * Maximum delay calc (Ch 1):
+ * clock prop + dram skew + max dqs prop delay + clk_adjust + min chip dly
+ * 1.46" * 180+ 350ps + 1.1" * 180 + 1563ps + 2595ps
+ * = 4968ps
+ * = 4.968ns
+ *
+ * Ch.0: 3.341ns to 5.673ns additional delay needed (pick 4.5ns as target)
+ * This is 1.8 clock cycles, pick CPO = READ_LAT + 7/4 (0x9)
+ * Ch.1: 2.822ns to 4.968ns additional delay needed (pick 3.9ns as target)
+ * This is 1.56 clock cycles, pick CPO = READ_LAT + 3/2 (0x8)
+ *
+ * Write latency (WR_DATA_DELAY) is calculated by doing the following:
+ *
+ * The DDR SDRAM specification requires DQS be received no sooner than
+ * 75% of an SDRAM clock period??and no later than 125% of a clock
+ * period??from the capturing clock edge of the command/address at the
+ * SDRAM.
+ *
+ * Based on the above tracelengths, the following are calculated:
+ * Ch. 0 8572 to DRAM propagation (DQ lanes) : 1.9" * 180 = 0.342ns
+ * Ch. 0 8572 to DRAM propagation (CLKs) : 2.3" * 180 = 0.414ns
+ * Ch. 1 8572 to DRAM propagation (DQ lanes) : 0.7" * 180 = 0.126ns
+ * Ch. 1 8572 to DRAM propagation (CLKs ) : 1.47" * 180 = 0.264ns
+ *
+ * Difference in arrival time CLK vs. DQS:
+ * Ch. 0 0.072ns
+ * Ch. 1 0.138ns
+ *
+ * Both of these values are much less than 25% of the clock
+ * period at DDR2-600 or DDR2-800, so no additional delay is needed over
+ * the 1/2 cycle which normally aligns the first DQS transition
+ * exactly WL (CAS latency minus one cycle) after the CAS strobe.
+ * See Figure 9-53 in MPC8572E manual: "1/2 delay" in Freescale's
+ * terminology corresponds to exactly one clock period delay after
+ * the CAS strobe. (due to the fact that the "delay" is referenced
+ * from the *falling* edge of the CLK, just after the rising edge
+ * which the CAS strobe is latched on.
+ */
+
+typedef struct board_memctl_options {
+ uint16_t datarate_mhz_low;
+ uint16_t datarate_mhz_high;
+ uint8_t clk_adjust;
+ uint8_t cpo_override;
+ uint8_t write_data_delay;
+} board_memctl_options_t;
+
+static struct board_memctl_options bopts_ctrl[][2] = {
+ {
+ /* Controller 0 */
+ {
+ /* DDR2 600/667 */
+ .datarate_mhz_low = 500,
+ .datarate_mhz_high = 750,
+ .clk_adjust = 5,
+ .cpo_override = 8,
+ .write_data_delay = 2,
+ },
+ {
+ /* DDR2 800 */
+ .datarate_mhz_low = 750,
+ .datarate_mhz_high = 850,
+ .clk_adjust = 5,
+ .cpo_override = 9,
+ .write_data_delay = 2,
+ },
+ },
+ {
+ /* Controller 1 */
+ {
+ /* DDR2 600/667 */
+ .datarate_mhz_low = 500,
+ .datarate_mhz_high = 750,
+ .clk_adjust = 5,
+ .cpo_override = 7,
+ .write_data_delay = 2,
+ },
+ {
+ /* DDR2 800 */
+ .datarate_mhz_low = 750,
+ .datarate_mhz_high = 850,
+ .clk_adjust = 5,
+ .cpo_override = 8,
+ .write_data_delay = 2,
+ },
+ },
+};
+
+void fsl_ddr_board_options(memctl_options_t *popts,
+ dimm_params_t *pdimm,
+ unsigned int ctrl_num)
+{
+ struct board_memctl_options *bopts = bopts_ctrl[ctrl_num];
+ sys_info_t sysinfo;
+ int i;
+ unsigned int datarate;
+
+ get_sys_info(&sysinfo);
+ datarate = sysinfo.freqDDRBus / 1000 / 1000;
+
+ for (i = 0; i < ARRAY_SIZE(bopts_ctrl[ctrl_num]); i++) {
+ if ((bopts[i].datarate_mhz_low <= datarate) &&
+ (bopts[i].datarate_mhz_high >= datarate)) {
+ debug("controller %d:\n", ctrl_num);
+ debug(" clk_adjust = %d\n", bopts[i].clk_adjust);
+ debug(" cpo = %d\n", bopts[i].cpo_override);
+ debug(" write_data_delay = %d\n",
+ bopts[i].write_data_delay);
+ popts->clk_adjust = bopts[i].clk_adjust;
+ popts->cpo_override = bopts[i].cpo_override;
+ popts->write_data_delay = bopts[i].write_data_delay;
+ }
+ }
+
+ /*
+ * Factors to consider for half-strength driver enable:
+ * - number of DIMMs installed
+ */
+ popts->half_strength_driver_enable = 0;
+}
diff --git a/board/xes/xpedite5370/law.c b/board/xes/xpedite5370/law.c
new file mode 100644
index 0000000..daee676
--- /dev/null
+++ b/board/xes/xpedite5370/law.c
@@ -0,0 +1,54 @@
+/*
+ * Copyright 2008 Extreme Engineering Solutions, Inc.
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/fsl_law.h>
+#include <asm/mmu.h>
+
+/*
+ * Notes:
+ * CCSRBAR and L2-as-SRAM don't need a configured Local Access Window.
+ * If flash is 8M at default position (last 8M), no LAW needed.
+ */
+
+struct law_entry law_table[] = {
+ SET_LAW(CONFIG_SYS_FLASH_BASE2, LAW_SIZE_256M, LAW_TRGT_IF_LBC),
+ SET_LAW(CONFIG_SYS_NAND_BASE, LAW_SIZE_1M, LAW_TRGT_IF_LBC),
+#ifdef CONFIG_SYS_PCIE1_MEM_PHYS
+ SET_LAW(CONFIG_SYS_PCIE1_MEM_PHYS, LAW_SIZE_1G, LAW_TRGT_IF_PCIE_1),
+ SET_LAW(CONFIG_SYS_PCIE1_IO_PHYS, LAW_SIZE_8M, LAW_TRGT_IF_PCIE_1),
+#endif
+#ifdef CONFIG_SYS_PCIE2_MEM_PHYS
+ SET_LAW(CONFIG_SYS_PCIE2_MEM_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_PCIE_2),
+ SET_LAW(CONFIG_SYS_PCIE2_IO_PHYS, LAW_SIZE_8M, LAW_TRGT_IF_PCIE_2),
+#endif
+#ifdef CONFIG_SYS_PCIE3_MEM_PHYS
+ SET_LAW(CONFIG_SYS_PCIE3_MEM_PHYS, LAW_SIZE_256M, LAW_TRGT_IF_PCIE_3),
+ SET_LAW(CONFIG_SYS_PCIE3_IO_PHYS, LAW_SIZE_8M, LAW_TRGT_IF_PCIE_3),
+#endif
+};
+
+int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/xes/xpedite5370/tlb.c b/board/xes/xpedite5370/tlb.c
new file mode 100644
index 0000000..caafa30
--- /dev/null
+++ b/board/xes/xpedite5370/tlb.c
@@ -0,0 +1,94 @@
+/*
+ * Copyright 2008 Extreme Engineering Solutions, Inc.
+ * Copyright 2008 Freescale Semiconductor, Inc.
+ *
+ * (C) Copyright 2000
+ * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/mmu.h>
+
+struct fsl_e_tlb_entry tlb_table[] = {
+ /* TLB 0 - for temp stack in cache */
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR, CONFIG_SYS_INIT_RAM_ADDR,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+ SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+ CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
+ MAS3_SX|MAS3_SW|MAS3_SR, 0,
+ 0, 0, BOOKE_PAGESZ_4K, 0),
+
+ /* W**G* - NOR flashes */
+ /* This will be changed to *I*G* after relocation to RAM. */
+ SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE2, CONFIG_SYS_FLASH_BASE2,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_W|MAS2_G,
+ 0, 0, BOOKE_PAGESZ_256M, 1),
+
+ /* *I*G* - CCSRBAR */
+ SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 1, BOOKE_PAGESZ_1M, 1),
+
+ /* *I*G* - NAND flash */
+ SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 2, BOOKE_PAGESZ_1M, 1),
+
+#ifdef CONFIG_PCIE1
+ /* *I*G* - PCIe */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_PHYS, CONFIG_SYS_PCIE1_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 3, BOOKE_PAGESZ_1G, 1),
+#endif
+
+#ifdef CONFIG_PCIE2
+ /* *I*G* - PCIe */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE2_MEM_PHYS, CONFIG_SYS_PCIE2_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 4, BOOKE_PAGESZ_256M, 1),
+#endif
+
+#ifdef CONFIG_PCIE3
+ /* *I*G* - PCIe */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE3_MEM_PHYS, CONFIG_SYS_PCIE3_MEM_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 5, BOOKE_PAGESZ_256M, 1),
+#endif
+
+#if defined(CONFIG_PCIE1) || defined(CONFIG_PCIE2) || defined(CONFIG_PCIE3)
+ /* *I*G* - PCIe */
+ SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_PHYS, CONFIG_SYS_PCIE1_IO_PHYS,
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 6, BOOKE_PAGESZ_64M, 1),
+#endif
+
+};
+
+int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/board/xes/xpedite5370/u-boot.lds b/board/xes/xpedite5370/u-boot.lds
new file mode 100644
index 0000000..cb39912
--- /dev/null
+++ b/board/xes/xpedite5370/u-boot.lds
@@ -0,0 +1,145 @@
+/*
+ * Copyright 2008 Extreme Engineering Solutions, Inc.
+ * Copyright 2007-2008 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+/* Do we need any of these for elf?
+ __DYNAMIC = 0; */
+PHDRS
+{
+ text PT_LOAD;
+ bss PT_LOAD;
+}
+
+SECTIONS
+{
+ /* Read-only sections, merged into text segment: */
+ . = + SIZEOF_HEADERS;
+ .interp : { *(.interp) }
+ .hash : { *(.hash) }
+ .dynsym : { *(.dynsym) }
+ .dynstr : { *(.dynstr) }
+ .rel.text : { *(.rel.text) }
+ .rela.text : { *(.rela.text) }
+ .rel.data : { *(.rel.data) }
+ .rela.data : { *(.rela.data) }
+ .rel.rodata : { *(.rel.rodata) }
+ .rela.rodata : { *(.rela.rodata) }
+ .rel.got : { *(.rel.got) }
+ .rela.got : { *(.rela.got) }
+ .rel.ctors : { *(.rel.ctors) }
+ .rela.ctors : { *(.rela.ctors) }
+ .rel.dtors : { *(.rel.dtors) }
+ .rela.dtors : { *(.rela.dtors) }
+ .rel.bss : { *(.rel.bss) }
+ .rela.bss : { *(.rela.bss) }
+ .rel.plt : { *(.rel.plt) }
+ .rela.plt : { *(.rela.plt) }
+ .init : { *(.init) }
+ .plt : { *(.plt) }
+ .text :
+ {
+ *(.text)
+ *(.got1)
+ } :text
+ _etext = .;
+ PROVIDE (etext = .);
+ .rodata :
+ {
+ *(.rodata)
+ *(.rodata1)
+ *(.rodata.str1.4)
+ *(.eh_frame)
+ } :text
+ .fini : { *(.fini) } =0
+ .ctors : { *(.ctors) }
+ .dtors : { *(.dtors) }
+
+ /* Read-write section, merged into data segment: */
+ . = (. + 0x00FF) & 0xFFFFFF00;
+ _erotext = .;
+ PROVIDE (erotext = .);
+ .reloc :
+ {
+ *(.got)
+ _GOT2_TABLE_ = .;
+ *(.got2)
+ _FIXUP_TABLE_ = .;
+ *(.fixup)
+ }
+ __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >> 2;
+ __fixup_entries = (. - _FIXUP_TABLE_) >> 2;
+
+ .data :
+ {
+ *(.data)
+ *(.data1)
+ *(.sdata)
+ *(.sdata2)
+ *(.dynamic)
+ CONSTRUCTORS
+ }
+ _edata = .;
+ PROVIDE (edata = .);
+
+ . = .;
+ __u_boot_cmd_start = .;
+ .u_boot_cmd : { *(.u_boot_cmd) }
+ __u_boot_cmd_end = .;
+
+ . = .;
+ __start___ex_table = .;
+ __ex_table : { *(__ex_table) }
+ __stop___ex_table = .;
+
+ . = ALIGN(256);
+ __init_begin = .;
+ .text.init : { *(.text.init) }
+ .data.init : { *(.data.init) }
+ . = ALIGN(256);
+ __init_end = .;
+
+ .bootpg ADDR(.text) + 0x7f000 :
+ {
+ cpu/mpc85xx/start.o (.bootpg)
+ } :text = 0xffff
+
+ .resetvec ADDR(.text) + 0x7fffc :
+ {
+ *(.resetvec)
+ } :text = 0xffff
+
+ . = ADDR(.text) + 0x80000;
+
+ __bss_start = .;
+ .bss (NOLOAD) :
+ {
+ *(.sbss) *(.scommon)
+ *(.dynbss)
+ *(.bss)
+ *(COMMON)
+ } :bss
+
+ . = ALIGN(4);
+ _end = . ;
+ PROVIDE (end = .);
+}
diff --git a/board/xes/xpedite5370/xpedite5370.c b/board/xes/xpedite5370/xpedite5370.c
new file mode 100644
index 0000000..2ddd121
--- /dev/null
+++ b/board/xes/xpedite5370/xpedite5370.c
@@ -0,0 +1,128 @@
+/*
+ * Copyright 2008 Extreme Engineering Solutions, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <command.h>
+#include <asm/processor.h>
+#include <asm/mmu.h>
+#include <asm/immap_85xx.h>
+#include <asm/immap_fsl_pci.h>
+#include <asm/io.h>
+#include <asm/cache.h>
+#include <libfdt.h>
+#include <fdt_support.h>
+#include <gpio/pca953x.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+extern void ft_board_pci_setup(void *blob, bd_t *bd);
+
+int checkboard(void)
+{
+ char *s;
+
+ printf("Board: X-ES %s 3U VPX SBC\n", CONFIG_SYS_BOARD_NAME);
+ printf(" ");
+ s = getenv("board_rev");
+ if (s)
+ printf("Rev %s, ", s);
+ s = getenv("serial#");
+ if (s)
+ printf("Serial# %s, ", s);
+ s = getenv("board_cfg");
+ if (s)
+ printf("Cfg %s", s);
+ printf("\n");
+
+ return 0;
+}
+
+static void flash_cs_fixup(void)
+{
+ volatile ccsr_lbc_t *lbc = (void *)(CONFIG_SYS_MPC85xx_LBC_ADDR);
+ int flash_sel;
+
+ /*
+ * Print boot dev and swap flash flash chip selects if booted from 2nd
+ * flash. Swapping chip selects presents user with a common memory
+ * map regardless of which flash was booted from.
+ */
+ flash_sel = !((pca953x_get_val(CONFIG_SYS_I2C_PCA953X_ADDR0) &
+ CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS));
+ printf("FLASH: Executed from FLASH%d\n", flash_sel ? 2 : 1);
+
+ if (flash_sel) {
+ lbc->br0 = CONFIG_SYS_BR1_PRELIM;
+ lbc->or0 = CONFIG_SYS_OR1_PRELIM;
+
+ lbc->br1 = CONFIG_SYS_BR0_PRELIM;
+ lbc->or1 = CONFIG_SYS_OR0_PRELIM;
+ }
+}
+
+int board_early_init_r(void)
+{
+ /* Initialize PCA9557 devices */
+ pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR0, 0xff, 0);
+ pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR1, 0xff, 0);
+ pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR0, 0xff, 0);
+ pca953x_set_pol(CONFIG_SYS_I2C_PCA953X_ADDR0, 0xff, 0);
+
+ /*
+ * Remap NOR flash region to caching-inhibited
+ * so that flash can be erased/programmed properly.
+ */
+
+ /* Flush d-cache and invalidate i-cache of any FLASH data */
+ flush_dcache();
+ invalidate_icache();
+
+ /* Invalidate existing TLB entry for NOR flash */
+ disable_tlb(0);
+ set_tlb(1, (CONFIG_SYS_FLASH_BASE2 & 0xf0000000),
+ (CONFIG_SYS_FLASH_BASE2 & 0xf0000000),
+ MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+ 0, 0, BOOKE_PAGESZ_256M, 1);
+
+ flash_cs_fixup();
+
+ return 0;
+}
+
+#if defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+#ifdef CONFIG_PCI
+ ft_board_pci_setup(blob, bd);
+#endif
+ ft_cpu_setup(blob, bd);
+}
+#endif
+
+#ifdef CONFIG_MP
+extern void cpu_mp_lmb_reserve(struct lmb *lmb);
+
+void board_lmb_reserve(struct lmb *lmb)
+{
+ cpu_mp_lmb_reserve(lmb);
+}
+#endif
diff --git a/include/configs/XPEDITE5370.h b/include/configs/XPEDITE5370.h
new file mode 100644
index 0000000..4d8b5cd
--- /dev/null
+++ b/include/configs/XPEDITE5370.h
@@ -0,0 +1,590 @@
+/*
+ * Copyright 2008 Extreme Engineering Solutions, Inc.
+ * Copyright 2007-2008 Freescale Semiconductor, Inc.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+/*
+ * xpedite5370 board configuration file
+ */
+#ifndef __CONFIG_H
+#define __CONFIG_H
+
+/*
+ * High Level Configuration Options
+ */
+#define CONFIG_BOOKE 1 /* BOOKE */
+#define CONFIG_E500 1 /* BOOKE e500 family */
+#define CONFIG_MPC85xx 1 /* MPC8540/60/55/41/48 */
+#define CONFIG_MPC8572 1
+#define CONFIG_XPEDITE5370 1
+#define CONFIG_SYS_BOARD_NAME "XPedite5370"
+#define CONFIG_NUM_CPUS 2 /* 2 Cores */
+#define CONFIG_BOARD_EARLY_INIT_R /* Call board_pre_init */
+#define CONFIG_RELOC_FIXUP_WORKS /* Fully relocate to SDRAM */
+
+#define CONFIG_PCI 1 /* Enable PCI/PCIE */
+#define CONFIG_PCI_PNP 1 /* do pci plug-and-play */
+#define CONFIG_PCI_SCAN_SHOW 1 /* show pci devices on startup */
+#define CONFIG_PCIE1 1 /* PCIE controler 1 */
+#define CONFIG_PCIE2 1 /* PCIE controler 2 */
+#define CONFIG_FSL_PCI_INIT 1 /* Use common FSL init code */
+#define CONFIG_SYS_PCI_64BIT 1 /* enable 64-bit PCI resources */
+#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe reset errata */
+#define CONFIG_FSL_LAW 1 /* Use common FSL init code */
+
+/*
+ * DDR config
+ */
+#define CONFIG_FSL_DDR2
+#undef CONFIG_FSL_DDR_INTERACTIVE
+#define CONFIG_SPD_EEPROM /* Use SPD EEPROM for DDR setup */
+#define CONFIG_DDR_SPD
+#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
+#define SPD_EEPROM_ADDRESS1 0x54 /* Both channels use the */
+#define SPD_EEPROM_ADDRESS2 0x54 /* same SPD data */
+#define SPD_EEPROM_OFFSET 0x200 /* OFFSET of SPD in EEPROM */
+#define CONFIG_NUM_DDR_CONTROLLERS 2
+#define CONFIG_DIMM_SLOTS_PER_CTLR 1
+#define CONFIG_CHIP_SELECTS_PER_CTRL 1
+#define CONFIG_DDR_ECC
+#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
+#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
+#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
+#define CONFIG_VERY_BIG_RAM
+
+#ifndef __ASSEMBLY__
+extern unsigned long get_board_sys_clk(unsigned long dummy);
+extern unsigned long get_board_ddr_clk(unsigned long dummy);
+#endif
+
+#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0) /* sysclk for MPC85xx */
+#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk(0) /* ddrclk for MPC85xx */
+
+/*
+ * These can be toggled for performance analysis, otherwise use default.
+ */
+#define CONFIG_L2_CACHE /* toggle L2 cache */
+#define CONFIG_BTB /* toggle branch predition */
+#define CONFIG_ENABLE_36BIT_PHYS 1
+
+/*
+ * Base addresses -- Note these are effective addresses where the
+ * actual resources get mapped (not physical addresses)
+ */
+#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /* CCSRBAR Default */
+#define CONFIG_SYS_CCSRBAR 0xef000000 /* relocated CCSRBAR */
+#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR /* physical addr of CCSRBAR */
+#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR /* PQII uses CONFIG_SYS_IMMR */
+#define CONFIG_SYS_PCIE1_ADDR (CONFIG_SYS_CCSRBAR + 0xa000)
+#define CONFIG_SYS_PCIE2_ADDR (CONFIG_SYS_CCSRBAR + 0x9000)
+
+/*
+ * Diagnostics
+ */
+#define CONFIG_SYS_ALT_MEMTEST
+#define CONFIG_SYS_MEMTEST_START 0x10000000
+#define CONFIG_SYS_MEMTEST_END 0x20000000
+
+/*
+ * Memory map
+ * 0x0000_0000 0x7fff_ffff DDR 2G Cacheable
+ * 0x8000_0000 0xbfff_ffff PCIe1 Mem 1G non-cacheable
+ * 0xc000_0000 0xcfff_ffff PCIe2 Mem 256M non-cacheable
+ * 0xe000_0000 0xe7ff_ffff SRAM/SSRAM/L1 Cache 128M non-cacheable
+ * 0xe800_0000 0xe87f_ffff PCIe1 IO 8M non-cacheable
+ * 0xe880_0000 0xe8ff_ffff PCIe2 IO 8M non-cacheable
+ * 0xef00_0000 0xef0f_ffff CCSR/IMMR 1M non-cacheable
+ * 0xef80_0000 0xef8f_ffff NAND Flash 1M non-cacheable
+ * 0xf000_0000 0xf7ff_ffff NOR Flash 2 128M non-cacheable
+ * 0xf800_0000 0xffff_ffff NOR Flash 1 128M non-cacheable
+ */
+
+#define CONFIG_SYS_LBC_LCRR (LCRR_CLKDIV_4 | LCRR_EADC_3)
+
+/*
+ * NAND flash configuration
+ */
+#define CONFIG_SYS_NAND_BASE 0xef800000
+#define CONFIG_SYS_NAND_BASE2 0xef840000 /* Unused at this time */
+
+/*
+ * NOR flash configuration
+ */
+#define CONFIG_SYS_FLASH_BASE 0xf8000000
+#define CONFIG_SYS_FLASH_BASE2 0xf0000000
+#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE2}
+#define CONFIG_SYS_MAX_FLASH_BANKS 2 /* number of banks */
+#define CONFIG_SYS_MAX_FLASH_SECT 1024 /* sectors per device */
+#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
+#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */
+#define CONFIG_FLASH_CFI_DRIVER
+#define CONFIG_SYS_FLASH_CFI
+#define CONFIG_SYS_FLASH_AUTOPROTECT_LIST { {0xfff40000, 0xc0000}, \
+ {0xf7f40000, 0xc0000} }
+#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /* start of monitor */
+
+/*
+ * Chip select configuration
+ */
+/* NOR Flash 0 on CS0 */
+#define CONFIG_SYS_BR0_PRELIM (CONFIG_SYS_FLASH_BASE | \
+ BR_PS_16 | \
+ BR_V)
+#define CONFIG_SYS_OR0_PRELIM (OR_AM_128MB | \
+ OR_GPCM_CSNT | \
+ OR_GPCM_XACS | \
+ OR_GPCM_ACS_DIV2 | \
+ OR_GPCM_SCY_8 | \
+ OR_GPCM_TRLX | \
+ OR_GPCM_EHTR | \
+ OR_GPCM_EAD)
+
+/* NOR Flash 1 on CS1 */
+#define CONFIG_SYS_BR1_PRELIM (CONFIG_SYS_FLASH_BASE2 | \
+ BR_PS_16 | \
+ BR_V)
+#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
+
+/* NAND flash on CS2 */
+#define CONFIG_SYS_BR2_PRELIM (CONFIG_SYS_NAND_BASE | \
+ (2<<BR_DECC_SHIFT) | \
+ BR_PS_8 | \
+ BR_MS_FCM | \
+ BR_V)
+
+/* NAND flash on CS2 */
+#define CONFIG_SYS_OR2_PRELIM (OR_AM_256KB | \
+ OR_FCM_PGS | \
+ OR_FCM_CSCT | \
+ OR_FCM_CST | \
+ OR_FCM_CHT | \
+ OR_FCM_SCY_1 | \
+ OR_FCM_TRLX | \
+ OR_FCM_EHTR)
+
+/* NAND flash on CS3 */
+#define CONFIG_SYS_BR3_PRELIM (CONFIG_SYS_NAND_BASE2 | \
+ (2<<BR_DECC_SHIFT) | \
+ BR_PS_8 | \
+ BR_MS_FCM | \
+ BR_V)
+#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM
+
+/*
+ * Use L1 as initial stack
+ */
+#define CONFIG_L1_INIT_RAM 1
+#define CONFIG_SYS_INIT_RAM_LOCK 1
+#define CONFIG_SYS_INIT_RAM_ADDR 0xe0000000
+#define CONFIG_SYS_INIT_RAM_END 0x00004000
+
+#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
+
+#define CONFIG_SYS_MONITOR_LEN (512 * 1024) /* Reserve 512 KB for Mon */
+#define CONFIG_SYS_MALLOC_LEN (1024 * 1024) /* Reserved for malloc */
+
+/*
+ * Serial Port
+ */
+#define CONFIG_CONS_INDEX 1
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE 1
+#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
+#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
+#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
+#define CONFIG_SYS_BAUDRATE_TABLE \
+ {300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
+#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
+
+/*
+ * Use the HUSH parser
+ */
+#define CONFIG_SYS_HUSH_PARSER
+#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
+
+/*
+ * Pass open firmware flat tree
+ */
+#define CONFIG_OF_LIBFDT 1
+#define CONFIG_OF_BOARD_SETUP 1
+#define CONFIG_OF_STDOUT_VIA_ALIAS 1
+
+#define CONFIG_SYS_64BIT_VSPRINTF 1
+#define CONFIG_SYS_64BIT_STRTOUL 1
+
+/*
+ * I2C
+ */
+#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
+#define CONFIG_HARD_I2C /* I2C with hardware support */
+#define CONFIG_SYS_I2C_SPEED 400000 /* I2C speed and slave address */
+#define CONFIG_SYS_I2C_SLAVE 0x7F
+#define CONFIG_SYS_I2C_OFFSET 0x3000
+#define CONFIG_SYS_I2C2_OFFSET 0x3100
+#define CONFIG_I2C_MULTI_BUS
+#define CONFIG_I2C_CMD_TREE
+
+/* PEX8518 slave I2C interface */
+#define CONFIG_SYS_I2C_PEX8518_ADDR 0x70
+
+/* I2C DS1631 temperature sensor */
+#define CONFIG_SYS_I2C_DS1621_ADDR 0x48
+#define CONFIG_DTT_DS1621
+#define CONFIG_DTT_SENSORS { 0 }
+
+/* I2C EEPROM - AT24C128B */
+#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 6 /* 64 byte pages */
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* take up to 10 msec */
+
+/* I2C RTC */
+#define CONFIG_RTC_M41T11 1
+#define CONFIG_SYS_I2C_RTC_ADDR 0x68
+#define CONFIG_SYS_M41T11_BASE_YEAR 2000
+
+/* GPIO/EEPROM/SRAM */
+#define CONFIG_DS4510
+#define CONFIG_SYS_I2C_DS4510_ADDR 0x51
+
+/* GPIO */
+#define CONFIG_PCA953X
+#define CONFIG_SYS_I2C_PCA953X_ADDR0 0x18
+#define CONFIG_SYS_I2C_PCA953X_ADDR1 0x1c
+#define CONFIG_SYS_I2C_PCA953X_ADDR2 0x1e
+#define CONFIG_SYS_I2C_PCA953X_ADDR3 0x1f
+#define CONFIG_SYS_I2C_PCA953X_ADDR CONFIG_SYS_I2C_PCA953X_ADDR0
+
+/*
+ * PU = pulled high, PD = pulled low
+ * I = input, O = output, IO = input/output
+ */
+/* PCA9557 @ 0x18*/
+#define CONFIG_SYS_PCA953X_C0_SER0_EN 0x01 /* PU; UART0 enable (1: enabled) */
+#define CONFIG_SYS_PCA953X_C0_SER0_MODE 0x02 /* PU; UART0 serial mode select */
+#define CONFIG_SYS_PCA953X_C0_SER1_EN 0x04 /* PU; UART1 enable (1: enabled) */
+#define CONFIG_SYS_PCA953X_C0_SER1_MODE 0x08 /* PU; UART1 serial mode select */
+#define CONFIG_SYS_PCA953X_C0_FLASH_PASS_CS 0x10 /* PU; Boot flash CS select */
+#define CONFIG_SYS_PCA953X_NVM_WP 0x20 /* PU; Set to 0 to enable NVM writing */
+#define CONFIG_SYS_PCA953X_C0_VCORE_VID2 0x40 /* VID2 of ISL6262 */
+#define CONFIG_SYS_PCA953X_C0_VCORE_VID3 0x80 /* VID3 of ISL6262 */
+
+/* PCA9557 @ 0x1c*/
+#define CONFIG_SYS_PCA953X_XMC0_ROOT0 0x01 /* PU; Low if XMC is RC */
+#define CONFIG_SYS_PCA953X_XMC0_MVMR0 0x02 /* XMC EEPROM write protect */
+#define CONFIG_SYS_PCA953X_XMC0_WAKE 0x04 /* PU; XMC wake */
+#define CONFIG_SYS_PCA953X_XMC0_BIST 0x08 /* PU; XMC built in self test */
+#define CONFIG_SYS_PCA953X_XMC_PRESENT 0x10 /* PU; Low if XMC module installed */
+#define CONFIG_SYS_PCA953X_PMC_PRESENT 0x20 /* PU; Low if PMC module installed */
+#define CONFIG_SYS_PCA953X_PMC0_MONARCH 0x40 /* PMC monarch mode enable */
+#define CONFIG_SYS_PCA953X_PMC0_EREADY 0x80 /* PU; PMC PCI eready */
+
+/* PCA9557 @ 0x1e*/
+#define CONFIG_SYS_PCA953X_P0_GA0 0x01 /* PU; VPX Geographical address */
+#define CONFIG_SYS_PCA953X_P0_GA1 0x02 /* PU; VPX Geographical address */
+#define CONFIG_SYS_PCA953X_P0_GA2 0x04 /* PU; VPX Geographical address */
+#define CONFIG_SYS_PCA953X_P0_GA3 0x08 /* PU; VPX Geographical address */
+#define CONFIG_SYS_PCA953X_P0_GA4 0x10 /* PU; VPX Geographical address */
+#define CONFIG_SYS_PCA953X_P0_GAP 0x20 /* PU; tied to VPX P0.GAP */
+#define CONFIG_SYS_PCA953X_P1_SYSEN 0x80 /* PU; Pulled high; tied to VPX P1.SYSCON */
+
+/* PCA9557 @ 0x1f */
+#define CONFIG_SYS_PCA953X_GPIO_VPX0 0x01 /* PU */
+#define CONFIG_SYS_PCA953X_GPIO_VPX1 0x02 /* PU */
+#define CONFIG_SYS_PCA953X_GPIO_VPX2 0x04 /* PU */
+#define CONFIG_SYS_PCA953X_GPIO_VPX3 0x08 /* PU */
+#define CONFIG_SYS_PCA953X_VPX_FRU_WRCTL 0x10 /* PD; I2C master source for FRU SEEPROM */
+
+/*
+ * General PCI
+ * Memory space is mapped 1-1, but I/O space must start from 0.
+ */
+/* PCIE1 - VPX P1 */
+#define CONFIG_SYS_PCIE1_MEM_BASE 0x80000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS CONFIG_SYS_PCIE1_MEM_BASE
+#define CONFIG_SYS_PCIE1_MEM_SIZE 0x40000000 /* 1G */
+#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xe8000000
+#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000 /* 8M */
+
+/* PCIE2 - PEX8518 */
+#define CONFIG_SYS_PCIE2_MEM_BASE 0xc0000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS CONFIG_SYS_PCIE2_MEM_BASE
+#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000 /* 256M */
+#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000
+#define CONFIG_SYS_PCIE2_IO_PHYS 0xe8800000
+#define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000 /* 8M */
+
+/*
+ * Networking options
+ */
+#define CONFIG_TSEC_ENET /* tsec ethernet support */
+#define CONFIG_PHY_GIGE 1 /* Include GbE speed/duplex detection */
+#define CONFIG_NET_MULTI 1
+#define CONFIG_TSEC_TBI
+#define CONFIG_MII 1 /* MII PHY management */
+#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow unregistered phys */
+#define CONFIG_ETHPRIME "eTSEC2"
+
+#define CONFIG_TSEC1 1
+#define CONFIG_TSEC1_NAME "eTSEC1"
+#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC1_PHY_ADDR 1
+#define TSEC1_PHYIDX 0
+#define CONFIG_HAS_ETH0
+
+#define CONFIG_TSEC2 1
+#define CONFIG_TSEC2_NAME "eTSEC2"
+#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
+#define TSEC2_PHY_ADDR 2
+#define TSEC2_PHYIDX 0
+#define CONFIG_HAS_ETH1
+
+/*
+ * Command configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DS4510
+#define CONFIG_CMD_DS4510_INFO
+#define CONFIG_CMD_DTT
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_JFFS2
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PCA953X
+#define CONFIG_CMD_PCA953X_INFO
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_SNTP
+
+/*
+ * Miscellaneous configurable options
+ */
+#define CONFIG_SYS_LONGHELP /* undef to save memory */
+#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */
+#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
+#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
+#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1ms ticks */
+#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
+#define CONFIG_LOADADDR 0x1000000 /* default location for tftp and bootm */
+#define CONFIG_BOOTDELAY 3 /* -1 disables auto-boot */
+#define CONFIG_PANIC_HANG /* do not reset board on panic */
+#define CONFIG_PREBOOT /* enable preboot variable */
+#define CONFIG_FIT 1
+#define CONFIG_FIT_VERBOSE 1
+#define CONFIG_INTEGRITY /* support booting INTEGRITY OS */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 16 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_SYS_BOOTMAPSZ (16 << 20) /* Initial Memory map for Linux*/
+
+/*
+ * Boot Flags
+ */
+#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
+#define BOOTFLAG_WARM 0x02 /* Software reboot */
+
+/*
+ * Environment Configuration
+ */
+#define CONFIG_ENV_IS_IN_FLASH 1
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128k (one sector) for env */
+#define CONFIG_ENV_SIZE 0x8000
+#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - (256 * 1024))
+
+/*
+ * Flash memory map:
+ * fff80000 - ffffffff Pri U-Boot (512 KB)
+ * fff40000 - fff7ffff Pri U-Boot Environment (256 KB)
+ * fff00000 - fff3ffff Pri FDT (256KB)
+ * fef00000 - ffefffff Pri OS image (16MB)
+ * f8000000 - feefffff Pri OS Use/Filesystem (111MB)
+ *
+ * f7f80000 - f7ffffff Sec U-Boot (512 KB)
+ * f7f40000 - f7f7ffff Sec U-Boot Environment (256 KB)
+ * f7f00000 - f7f3ffff Sec FDT (256KB)
+ * f6f00000 - f7efffff Sec OS image (16MB)
+ * f0000000 - f6efffff Sec OS Use/Filesystem (111MB)
+ */
+#define CONFIG_UBOOT1_ENV_ADDR MK_STR(0xfff80000)
+#define CONFIG_UBOOT2_ENV_ADDR MK_STR(0xf7f80000)
+#define CONFIG_FDT1_ENV_ADDR MK_STR(0xfff00000)
+#define CONFIG_FDT2_ENV_ADDR MK_STR(0xf7f00000)
+#define CONFIG_OS1_ENV_ADDR MK_STR(0xfef00000)
+#define CONFIG_OS2_ENV_ADDR MK_STR(0xf6f00000)
+
+#define CONFIG_PROG_UBOOT1 \
+ "$download_cmd $loadaddr $ubootfile; " \
+ "if test $? -eq 0; then " \
+ "protect off "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
+ "erase "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
+ "cp.w $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 40000; " \
+ "protect on "CONFIG_UBOOT1_ENV_ADDR" +80000; " \
+ "cmp.b $loadaddr "CONFIG_UBOOT1_ENV_ADDR" 80000; " \
+ "if test $? -ne 0; then " \
+ "echo PROGRAM FAILED; " \
+ "else; " \
+ "echo PROGRAM SUCCEEDED; " \
+ "fi; " \
+ "else; " \
+ "echo DOWNLOAD FAILED; " \
+ "fi;"
+
+#define CONFIG_PROG_UBOOT2 \
+ "$download_cmd $loadaddr $ubootfile; " \
+ "if test $? -eq 0; then " \
+ "protect off "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
+ "erase "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
+ "cp.w $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 40000; " \
+ "protect on "CONFIG_UBOOT2_ENV_ADDR" +80000; " \
+ "cmp.b $loadaddr "CONFIG_UBOOT2_ENV_ADDR" 80000; " \
+ "if test $? -ne 0; then " \
+ "echo PROGRAM FAILED; " \
+ "else; " \
+ "echo PROGRAM SUCCEEDED; " \
+ "fi; " \
+ "else; " \
+ "echo DOWNLOAD FAILED; " \
+ "fi;"
+
+#define CONFIG_BOOT_OS_NET \
+ "$download_cmd $osaddr $osfile; " \
+ "if test $? -eq 0; then " \
+ "if test -n $fdtaddr; then " \
+ "$download_cmd $fdtaddr $fdtfile; " \
+ "if test $? -eq 0; then " \
+ "bootm $osaddr - $fdtaddr; " \
+ "else; " \
+ "echo FDT DOWNLOAD FAILED; " \
+ "fi; " \
+ "else; " \
+ "bootm $osaddr; " \
+ "fi; " \
+ "else; " \
+ "echo OS DOWNLOAD FAILED; " \
+ "fi;"
+
+#define CONFIG_PROG_OS1 \
+ "$download_cmd $osaddr $osfile; " \
+ "if test $? -eq 0; then " \
+ "erase "CONFIG_OS1_ENV_ADDR" +$filesize; " \
+ "cp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \
+ "cmp.b $osaddr "CONFIG_OS1_ENV_ADDR" $filesize; " \
+ "if test $? -ne 0; then " \
+ "echo OS PROGRAM FAILED; " \
+ "else; " \
+ "echo OS PROGRAM SUCCEEDED; " \
+ "fi; " \
+ "else; " \
+ "echo OS DOWNLOAD FAILED; " \
+ "fi;"
+
+#define CONFIG_PROG_OS2 \
+ "$download_cmd $osaddr $osfile; " \
+ "if test $? -eq 0; then " \
+ "erase "CONFIG_OS2_ENV_ADDR" +$filesize; " \
+ "cp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \
+ "cmp.b $osaddr "CONFIG_OS2_ENV_ADDR" $filesize; " \
+ "if test $? -ne 0; then " \
+ "echo OS PROGRAM FAILED; " \
+ "else; " \
+ "echo OS PROGRAM SUCCEEDED; " \
+ "fi; " \
+ "else; " \
+ "echo OS DOWNLOAD FAILED; " \
+ "fi;"
+
+#define CONFIG_PROG_FDT1 \
+ "$download_cmd $fdtaddr $fdtfile; " \
+ "if test $? -eq 0; then " \
+ "erase "CONFIG_FDT1_ENV_ADDR" +$filesize;" \
+ "cp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \
+ "cmp.b $fdtaddr "CONFIG_FDT1_ENV_ADDR" $filesize; " \
+ "if test $? -ne 0; then " \
+ "echo FDT PROGRAM FAILED; " \
+ "else; " \
+ "echo FDT PROGRAM SUCCEEDED; " \
+ "fi; " \
+ "else; " \
+ "echo FDT DOWNLOAD FAILED; " \
+ "fi;"
+
+#define CONFIG_PROG_FDT2 \
+ "$download_cmd $fdtaddr $fdtfile; " \
+ "if test $? -eq 0; then " \
+ "erase "CONFIG_FDT2_ENV_ADDR" +$filesize;" \
+ "cp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \
+ "cmp.b $fdtaddr "CONFIG_FDT2_ENV_ADDR" $filesize; " \
+ "if test $? -ne 0; then " \
+ "echo FDT PROGRAM FAILED; " \
+ "else; " \
+ "echo FDT PROGRAM SUCCEEDED; " \
+ "fi; " \
+ "else; " \
+ "echo FDT DOWNLOAD FAILED; " \
+ "fi;"
+
+#define CONFIG_EXTRA_ENV_SETTINGS \
+ "autoload=yes\0" \
+ "download_cmd=tftp\0" \
+ "console_args=console=ttyS0,115200\0" \
+ "root_args=root=/dev/nfs rw\0" \
+ "misc_args=ip=on\0" \
+ "set_bootargs=setenv bootargs ${console_args} ${root_args} ${misc_args}\0" \
+ "bootfile=/home/user/file\0" \
+ "osfile=/home/user/uImage-XPedite5370\0" \
+ "fdtfile=/home/user/xpedite5370.dtb\0" \
+ "ubootfile=/home/user/u-boot.bin\0" \
+ "fdtaddr=c00000\0" \
+ "osaddr=0x1000000\0" \
+ "loadaddr=0x1000000\0" \
+ "prog_uboot1="CONFIG_PROG_UBOOT1"\0" \
+ "prog_uboot2="CONFIG_PROG_UBOOT2"\0" \
+ "prog_os1="CONFIG_PROG_OS1"\0" \
+ "prog_os2="CONFIG_PROG_OS2"\0" \
+ "prog_fdt1="CONFIG_PROG_FDT1"\0" \
+ "prog_fdt2="CONFIG_PROG_FDT2"\0" \
+ "bootcmd_net=run set_bootargs; "CONFIG_BOOT_OS_NET"\0" \
+ "bootcmd_flash1=run set_bootargs; " \
+ "bootm "CONFIG_OS1_ENV_ADDR" - "CONFIG_FDT1_ENV_ADDR"\0"\
+ "bootcmd_flash2=run set_bootargs; " \
+ "bootm "CONFIG_OS2_ENV_ADDR" - "CONFIG_FDT2_ENV_ADDR"\0"\
+ "bootcmd=run bootcmd_flash1\0"
+#endif /* __CONFIG_H */
--
1.6.0.2.GIT
^ permalink raw reply related [flat|nested] 4+ messages in thread