* [PATCH V6 3/4] drm/bridge: Add driver for GE B850v3 LVDS/DP++ Bridge
@ 2016-10-27 13:01 ` Peter Senna Tschudin
0 siblings, 0 replies; 17+ messages in thread
From: Peter Senna Tschudin @ 2016-10-27 13:01 UTC (permalink / raw)
To: airlied, architt, akpm, daniel.vetter, davem, devicetree,
dri-devel, enric.balletbo, eballetbo, galak, gregkh, heiko,
ijc+devicetree, javier, jslaby, kernel, linux-arm-kernel, linux,
linux-kernel, linux, mark.rutland, martin.donnelly, martyn.welch,
mchehab, pawel.moll, peter.senna, peter.senna, p.zabel,
thierry.reding, rmk+kernel, robh+dt, shawnguo, tiwai, treding,
ykk
Cc: Rob Herring, Fabio Estevam
Add a driver that create a drm_bridge and a drm_connector for the LVDS
to DP++ display bridge of the GE B850v3.
There are two physical bridges on the video signal pipeline: a
STDP4028(LVDS to DP) and a STDP2690(DP to DP++). The hardware and
firmware made it complicated for this binding to comprise two device
tree nodes, as the design goal is to configure both bridges based on
the LVDS signal, which leave the driver powerless to control the video
processing pipeline. The two bridges behaves as a single bridge, and
the driver is only needed for telling the host about EDID / HPD, and
for giving the host powers to ack interrupts. The video signal pipeline
is as follows:
Host -> LVDS|--(STDP4028)--|DP -> DP|--(STDP2690)--|DP++ -> Video output
Cc: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Martin Donnelly <martin.donnelly@ge.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Rob Herring <robh@kernel.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
CC: David Airlie <airlied@linux.ie>
CC: Thierry Reding <treding@nvidia.com>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Enric Balletbo <enric.balletbo@collabora.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
---
Changes from V5:
- Reworked interrupt handler initialization
- Removed useless calls to: drm_connector_register(),
drm_helper_hpd_irq_event(), and drm_bridge_enable()
Changes from V4:
- Renamed the i2c_driver.name from "ge,b850v3-lvds-dp" to "b850v3-lvds-dp" to
remove the comma from the driver name
Changes from V3:
- 3/4 instead of 4/5
- Tested on next-20160804
Changes from V2:
- Made it atomic to be applied on next-20160729 on top of Liu Ying changes
that made imx-ldb atomic
Changes from V1:
- New commit message
- Removed 3 empty entry points
- Removed memory leak from ge_b850v3_lvds_dp_get_modes()
- Added a lock for mode setting
- Removed a few blank lines
- Changed the order at Makefile and Kconfig
drivers/gpu/drm/bridge/Kconfig | 11 +
drivers/gpu/drm/bridge/Makefile | 1 +
drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c | 395 +++++++++++++++++++++++++++++
3 files changed, 407 insertions(+)
create mode 100644 drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c
diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig
index bd6acc8..1d02422 100644
--- a/drivers/gpu/drm/bridge/Kconfig
+++ b/drivers/gpu/drm/bridge/Kconfig
@@ -39,6 +39,17 @@ config DRM_DW_HDMI_AHB_AUDIO
Designware HDMI block. This is used in conjunction with
the i.MX6 HDMI driver.
+config DRM_GE_B850V3_LVDS_DP
+ tristate "GE B850v3 LVDS to DP++ display bridge"
+ depends on OF
+ select DRM_KMS_HELPER
+ select DRM_PANEL
+ ---help---
+ This is a driver for the display bridge of
+ GE B850v3 that convert dual channel LVDS
+ to DP++. This is used with the i.MX6 imx-ldb
+ driver.
+
config DRM_NXP_PTN3460
tristate "NXP PTN3460 DP/LVDS bridge"
depends on OF
diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile
index 97ed1a5..b6b44a5 100644
--- a/drivers/gpu/drm/bridge/Makefile
+++ b/drivers/gpu/drm/bridge/Makefile
@@ -5,6 +5,7 @@ obj-$(CONFIG_DRM_DUMB_VGA_DAC) += dumb-vga-dac.o
obj-$(CONFIG_DRM_DW_HDMI) += dw-hdmi.o
obj-$(CONFIG_DRM_DW_HDMI_AHB_AUDIO) += dw-hdmi-ahb-audio.o
obj-$(CONFIG_DRM_NXP_PTN3460) += nxp-ptn3460.o
+obj-$(CONFIG_DRM_GE_B850V3_LVDS_DP) += ge_b850v3_lvds_dp.o
obj-$(CONFIG_DRM_PARADE_PS8622) += parade-ps8622.o
obj-$(CONFIG_DRM_SIL_SII8620) += sil-sii8620.o
obj-$(CONFIG_DRM_SII902X) += sii902x.o
diff --git a/drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c b/drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c
new file mode 100644
index 0000000..85875d8
--- /dev/null
+++ b/drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c
@@ -0,0 +1,395 @@
+/*
+ * Driver for GE B850v3 DP display bridge
+
+ * Copyright (c) 2016, Collabora Ltd.
+ * Copyright (c) 2016, General Electric Company
+
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+
+ * This driver creates a drm_bridge and a drm_connector for the LVDS to DP++
+ * display bridge of the GE B850v3. There are two physical bridges on the video
+ * signal pipeline: a STDP4028(LVDS to DP) and a STDP2690(DP to DP++). However
+ * the physical bridges are automatically configured by the input video signal,
+ * and the driver has no access to the video processing pipeline. The driver is
+ * only needed to read EDID from the STDP2690 and to handle HPD events from the
+ * STDP4028. The driver communicates with both bridges over i2c. The video
+ * signal pipeline is as follows:
+ *
+ * Host -> LVDS|--(STDP4028)--|DP -> DP|--(STDP2690)--|DP++ -> Video output
+ *
+ */
+
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <drm/drm_atomic.h>
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_edid.h>
+#include <drm/drmP.h>
+
+/*
+ * 220Mhz is a limitation of the host, as the bridge is capable of up to
+ * 330Mhz. See section 9.2.1.2.4 of the i.MX 6Dual/6Quad Applications
+ * Processor Reference Manual for more information about the 220Mhz limit.
+ * The imx-ldb driver will warn about clocks over 170Mhz, but it seem to work
+ * fine.
+ */
+#define MAX_PIXEL_CLOCK 220000
+
+#define EDID_EXT_BLOCK_CNT 0x7E
+
+#define STDP4028_IRQ_OUT_CONF_REG 0x02
+#define STDP4028_DPTX_IRQ_EN_REG 0x3C
+#define STDP4028_DPTX_IRQ_STS_REG 0x3D
+#define STDP4028_DPTX_STS_REG 0x3E
+
+#define STDP4028_DPTX_DP_IRQ_EN 0x1000
+
+#define STDP4028_DPTX_HOTPLUG_IRQ_EN 0x0400
+#define STDP4028_DPTX_LINK_CH_IRQ_EN 0x2000
+#define STDP4028_DPTX_IRQ_CONFIG \
+ (STDP4028_DPTX_LINK_CH_IRQ_EN | STDP4028_DPTX_HOTPLUG_IRQ_EN)
+
+#define STDP4028_DPTX_HOTPLUG_STS 0x0200
+#define STDP4028_DPTX_LINK_STS 0x1000
+#define STDP4028_CON_STATE_CONNECTED \
+ (STDP4028_DPTX_HOTPLUG_STS | STDP4028_DPTX_LINK_STS)
+
+#define STDP4028_DPTX_HOTPLUG_CH_STS 0x0400
+#define STDP4028_DPTX_LINK_CH_STS 0x2000
+#define STDP4028_DPTX_IRQ_CLEAR \
+ (STDP4028_DPTX_LINK_CH_STS | STDP4028_DPTX_HOTPLUG_CH_STS)
+
+struct ge_b850v3_lvds_dp {
+ struct drm_connector connector;
+ struct drm_bridge bridge;
+ struct i2c_client *ge_b850v3_lvds_dp_i2c;
+ struct i2c_client *edid_i2c;
+ struct edid *edid;
+ struct mutex lock;
+};
+
+static inline struct ge_b850v3_lvds_dp *
+ bridge_to_ge_b850v3_lvds_dp(struct drm_bridge *bridge)
+{
+ return container_of(bridge, struct ge_b850v3_lvds_dp, bridge);
+}
+
+static inline struct ge_b850v3_lvds_dp *
+ connector_to_ge_b850v3_lvds_dp(struct drm_connector *connector)
+{
+ return container_of(connector, struct ge_b850v3_lvds_dp, connector);
+}
+
+u8 *stdp2690_get_edid(struct i2c_client *client)
+{
+ struct i2c_adapter *adapter = client->adapter;
+ unsigned char start = 0x00;
+ unsigned int total_size;
+ u8 *block = kmalloc(EDID_LENGTH, GFP_KERNEL);
+
+ struct i2c_msg msgs[] = {
+ {
+ .addr = client->addr,
+ .flags = 0,
+ .len = 1,
+ .buf = &start,
+ }, {
+ .addr = client->addr,
+ .flags = I2C_M_RD,
+ .len = EDID_LENGTH,
+ .buf = block,
+ }
+ };
+
+ if (!block)
+ return NULL;
+
+ if (i2c_transfer(adapter, msgs, 2) != 2) {
+ DRM_ERROR("Unable to read EDID.\n");
+ goto err;
+ }
+
+ if (!drm_edid_block_valid(block, 0, false, NULL)) {
+ DRM_ERROR("Invalid EDID block\n");
+ goto err;
+ }
+
+ total_size = (block[EDID_EXT_BLOCK_CNT] + 1) * EDID_LENGTH;
+ if (total_size > EDID_LENGTH) {
+ kfree(block);
+ block = kmalloc(total_size, GFP_KERNEL);
+ if (!block)
+ return NULL;
+
+ /* Yes, read the entire buffer, and do not skip the first
+ * EDID_LENGTH bytes.
+ */
+ start = 0x00;
+ msgs[1].len = total_size;
+ msgs[1].buf = block;
+
+ if (i2c_transfer(adapter, msgs, 2) != 2) {
+ DRM_ERROR("Unable to read EDID extension blocks.\n");
+ goto err;
+ }
+ }
+
+ return block;
+
+err:
+ kfree(block);
+ return NULL;
+}
+
+static int ge_b850v3_lvds_dp_get_modes(struct drm_connector *connector)
+{
+ struct ge_b850v3_lvds_dp *ptn_bridge;
+ struct i2c_client *client;
+ int num_modes = 0;
+
+ ptn_bridge = connector_to_ge_b850v3_lvds_dp(connector);
+ client = ptn_bridge->edid_i2c;
+
+ mutex_lock(&ptn_bridge->lock);
+
+ kfree(ptn_bridge->edid);
+ ptn_bridge->edid = (struct edid *) stdp2690_get_edid(client);
+
+ if (ptn_bridge->edid) {
+ drm_mode_connector_update_edid_property(connector,
+ ptn_bridge->edid);
+ num_modes = drm_add_edid_modes(connector, ptn_bridge->edid);
+ }
+
+ mutex_unlock(&ptn_bridge->lock);
+
+ return num_modes;
+}
+
+
+static enum drm_mode_status ge_b850v3_lvds_dp_mode_valid(
+ struct drm_connector *connector, struct drm_display_mode *mode)
+{
+ if (mode->clock > MAX_PIXEL_CLOCK) {
+ DRM_INFO("The pixel clock for the mode %s is too high, and not supported.",
+ mode->name);
+ return MODE_CLOCK_HIGH;
+ }
+
+ return MODE_OK;
+}
+
+static const struct
+drm_connector_helper_funcs ge_b850v3_lvds_dp_connector_helper_funcs = {
+ .get_modes = ge_b850v3_lvds_dp_get_modes,
+ .mode_valid = ge_b850v3_lvds_dp_mode_valid,
+};
+
+static enum drm_connector_status ge_b850v3_lvds_dp_detect(
+ struct drm_connector *connector, bool force)
+{
+ struct ge_b850v3_lvds_dp *ptn_bridge =
+ connector_to_ge_b850v3_lvds_dp(connector);
+ struct i2c_client *ge_b850v3_lvds_dp_i2c =
+ ptn_bridge->ge_b850v3_lvds_dp_i2c;
+ s32 link_state;
+
+ link_state = i2c_smbus_read_word_data(ge_b850v3_lvds_dp_i2c,
+ STDP4028_DPTX_STS_REG);
+
+ if (link_state == STDP4028_CON_STATE_CONNECTED)
+ return connector_status_connected;
+
+ if (link_state == 0)
+ return connector_status_disconnected;
+
+ return connector_status_unknown;
+}
+
+static const struct drm_connector_funcs ge_b850v3_lvds_dp_connector_funcs = {
+ .dpms = drm_atomic_helper_connector_dpms,
+ .fill_modes = drm_helper_probe_single_connector_modes,
+ .detect = ge_b850v3_lvds_dp_detect,
+ .destroy = drm_connector_cleanup,
+ .reset = drm_atomic_helper_connector_reset,
+ .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
+ .atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
+};
+
+static irqreturn_t ge_b850v3_lvds_dp_irq_handler(int irq, void *dev_id)
+{
+ struct ge_b850v3_lvds_dp *ptn_bridge = dev_id;
+ struct i2c_client *ge_b850v3_lvds_dp_i2c
+ = ptn_bridge->ge_b850v3_lvds_dp_i2c;
+
+ mutex_lock(&ptn_bridge->lock);
+
+ i2c_smbus_write_word_data(ge_b850v3_lvds_dp_i2c,
+ STDP4028_DPTX_IRQ_STS_REG, STDP4028_DPTX_IRQ_CLEAR);
+
+ mutex_unlock(&ptn_bridge->lock);
+
+ if (ptn_bridge->connector.dev)
+ drm_kms_helper_hotplug_event(ptn_bridge->connector.dev);
+
+ return IRQ_HANDLED;
+}
+
+static int ge_b850v3_lvds_dp_attach(struct drm_bridge *bridge)
+{
+ struct ge_b850v3_lvds_dp *ptn_bridge
+ = bridge_to_ge_b850v3_lvds_dp(bridge);
+ struct drm_connector *connector = &ptn_bridge->connector;
+ struct i2c_client *ge_b850v3_lvds_dp_i2c
+ = ptn_bridge->ge_b850v3_lvds_dp_i2c;
+ int ret;
+
+ if (!bridge->encoder) {
+ DRM_ERROR("Parent encoder object not found");
+ return -ENODEV;
+ }
+
+ connector->polled = DRM_CONNECTOR_POLL_HPD;
+
+ drm_connector_helper_add(connector,
+ &ge_b850v3_lvds_dp_connector_helper_funcs);
+
+ ret = drm_connector_init(bridge->dev, connector,
+ &ge_b850v3_lvds_dp_connector_funcs,
+ DRM_MODE_CONNECTOR_DisplayPort);
+ if (ret) {
+ DRM_ERROR("Failed to initialize connector with drm\n");
+ return ret;
+ }
+
+ ret = drm_mode_connector_attach_encoder(connector, bridge->encoder);
+ if (ret)
+ return ret;
+
+ /* Configures the bridge to re-enable interrupts after each ack. */
+ i2c_smbus_write_word_data(ge_b850v3_lvds_dp_i2c,
+ STDP4028_IRQ_OUT_CONF_REG, STDP4028_DPTX_DP_IRQ_EN);
+
+ /* Enable interrupts */
+ i2c_smbus_write_word_data(ge_b850v3_lvds_dp_i2c,
+ STDP4028_DPTX_IRQ_EN_REG, STDP4028_DPTX_IRQ_CONFIG);
+
+ return 0;
+}
+
+static const struct drm_bridge_funcs ge_b850v3_lvds_dp_funcs = {
+ .attach = ge_b850v3_lvds_dp_attach,
+};
+
+static int ge_b850v3_lvds_dp_probe(struct i2c_client *ge_b850v3_lvds_dp_i2c,
+ const struct i2c_device_id *id)
+{
+ struct device *dev = &ge_b850v3_lvds_dp_i2c->dev;
+ struct ge_b850v3_lvds_dp *ptn_bridge;
+ int ret;
+ u32 edid_i2c_reg;
+
+ ptn_bridge = devm_kzalloc(dev, sizeof(*ptn_bridge), GFP_KERNEL);
+ if (!ptn_bridge)
+ return -ENOMEM;
+
+ mutex_init(&ptn_bridge->lock);
+
+ ptn_bridge->ge_b850v3_lvds_dp_i2c = ge_b850v3_lvds_dp_i2c;
+ ptn_bridge->bridge.driver_private = ptn_bridge;
+ i2c_set_clientdata(ge_b850v3_lvds_dp_i2c, ptn_bridge);
+
+ ret = of_property_read_u32(dev->of_node, "edid-reg", &edid_i2c_reg);
+ if (ret) {
+ dev_err(dev, "edid-reg not specified, aborting...\n");
+ return -ENODEV;
+ }
+
+ ptn_bridge->edid_i2c = devm_kzalloc(dev,
+ sizeof(struct i2c_client), GFP_KERNEL);
+
+ if (!ptn_bridge->edid_i2c)
+ return -ENOMEM;
+
+ memcpy(ptn_bridge->edid_i2c, ge_b850v3_lvds_dp_i2c,
+ sizeof(struct i2c_client));
+
+ ptn_bridge->edid_i2c->addr = (unsigned short) edid_i2c_reg;
+
+ ptn_bridge->bridge.funcs = &ge_b850v3_lvds_dp_funcs;
+ ptn_bridge->bridge.of_node = dev->of_node;
+ ret = drm_bridge_add(&ptn_bridge->bridge);
+ if (ret) {
+ DRM_ERROR("Failed to add bridge\n");
+ return ret;
+ }
+
+ /* Clear pending interrupts since power up. */
+ i2c_smbus_write_word_data(ge_b850v3_lvds_dp_i2c,
+ STDP4028_DPTX_IRQ_STS_REG, STDP4028_DPTX_IRQ_CLEAR);
+
+ if (ge_b850v3_lvds_dp_i2c->irq) {
+ ret = devm_request_threaded_irq(&ge_b850v3_lvds_dp_i2c->dev,
+ ge_b850v3_lvds_dp_i2c->irq, NULL,
+ ge_b850v3_lvds_dp_irq_handler,
+ IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
+ "ge-b850v3-lvds-dp", ptn_bridge);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+static int ge_b850v3_lvds_dp_remove(struct i2c_client *ge_b850v3_lvds_dp_i2c)
+{
+ struct ge_b850v3_lvds_dp *ptn_bridge =
+ i2c_get_clientdata(ge_b850v3_lvds_dp_i2c);
+
+ drm_bridge_remove(&ptn_bridge->bridge);
+
+ kfree(ptn_bridge->edid);
+
+ return 0;
+}
+
+static const struct i2c_device_id ge_b850v3_lvds_dp_i2c_table[] = {
+ {"b850v3-lvds-dp", 0},
+ {},
+};
+MODULE_DEVICE_TABLE(i2c, ge_b850v3_lvds_dp_i2c_table);
+
+static const struct of_device_id ge_b850v3_lvds_dp_match[] = {
+ { .compatible = "ge,b850v3-lvds-dp" },
+ {},
+};
+MODULE_DEVICE_TABLE(of, ge_b850v3_lvds_dp_match);
+
+static struct i2c_driver ge_b850v3_lvds_dp_driver = {
+ .id_table = ge_b850v3_lvds_dp_i2c_table,
+ .probe = ge_b850v3_lvds_dp_probe,
+ .remove = ge_b850v3_lvds_dp_remove,
+ .driver = {
+ .name = "b850v3-lvds-dp",
+ .of_match_table = ge_b850v3_lvds_dp_match,
+ },
+};
+module_i2c_driver(ge_b850v3_lvds_dp_driver);
+
+MODULE_AUTHOR("Peter Senna Tschudin <peter.senna@collabora.com>");
+MODULE_AUTHOR("Martyn Welch <martyn.welch@collabora.co.uk>");
+MODULE_DESCRIPTION("GE LVDS to DP++ display bridge)");
+MODULE_LICENSE("GPL v2");
--
2.5.5
^ permalink raw reply related [flat|nested] 17+ messages in thread* [PATCH V6 3/4] drm/bridge: Add driver for GE B850v3 LVDS/DP++ Bridge
@ 2016-10-27 13:01 ` Peter Senna Tschudin
0 siblings, 0 replies; 17+ messages in thread
From: Peter Senna Tschudin @ 2016-10-27 13:01 UTC (permalink / raw)
To: airlied, architt, akpm, daniel.vetter, davem, devicetree,
dri-devel, enric.balletbo, eballetbo, galak, gregkh, heiko,
ijc+devicetree, javier, jslaby, kernel, linux-arm-kernel, linux,
linux-kernel, linux, mark.rutland, martin.donnelly, martyn.welch,
mchehab, pawel.moll, peter.senna, peter.senna, p.zabel,
thierry.reding, rmk+kernel, robh+dt, shawnguo, tiwai, treding,
ykk
Cc: Fabio Estevam
Add a driver that create a drm_bridge and a drm_connector for the LVDS
to DP++ display bridge of the GE B850v3.
There are two physical bridges on the video signal pipeline: a
STDP4028(LVDS to DP) and a STDP2690(DP to DP++). The hardware and
firmware made it complicated for this binding to comprise two device
tree nodes, as the design goal is to configure both bridges based on
the LVDS signal, which leave the driver powerless to control the video
processing pipeline. The two bridges behaves as a single bridge, and
the driver is only needed for telling the host about EDID / HPD, and
for giving the host powers to ack interrupts. The video signal pipeline
is as follows:
Host -> LVDS|--(STDP4028)--|DP -> DP|--(STDP2690)--|DP++ -> Video output
Cc: Martyn Welch <martyn.welch@collabora.co.uk>
Cc: Martin Donnelly <martin.donnelly@ge.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Rob Herring <robh@kernel.org>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
CC: David Airlie <airlied@linux.ie>
CC: Thierry Reding <treding@nvidia.com>
CC: Thierry Reding <thierry.reding@gmail.com>
CC: Archit Taneja <architt@codeaurora.org>
Reviewed-by: Enric Balletbo <enric.balletbo@collabora.com>
Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
---
Changes from V5:
- Reworked interrupt handler initialization
- Removed useless calls to: drm_connector_register(),
drm_helper_hpd_irq_event(), and drm_bridge_enable()
Changes from V4:
- Renamed the i2c_driver.name from "ge,b850v3-lvds-dp" to "b850v3-lvds-dp" to
remove the comma from the driver name
Changes from V3:
- 3/4 instead of 4/5
- Tested on next-20160804
Changes from V2:
- Made it atomic to be applied on next-20160729 on top of Liu Ying changes
that made imx-ldb atomic
Changes from V1:
- New commit message
- Removed 3 empty entry points
- Removed memory leak from ge_b850v3_lvds_dp_get_modes()
- Added a lock for mode setting
- Removed a few blank lines
- Changed the order at Makefile and Kconfig
drivers/gpu/drm/bridge/Kconfig | 11 +
drivers/gpu/drm/bridge/Makefile | 1 +
drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c | 395 +++++++++++++++++++++++++++++
3 files changed, 407 insertions(+)
create mode 100644 drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c
diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig
index bd6acc8..1d02422 100644
--- a/drivers/gpu/drm/bridge/Kconfig
+++ b/drivers/gpu/drm/bridge/Kconfig
@@ -39,6 +39,17 @@ config DRM_DW_HDMI_AHB_AUDIO
Designware HDMI block. This is used in conjunction with
the i.MX6 HDMI driver.
+config DRM_GE_B850V3_LVDS_DP
+ tristate "GE B850v3 LVDS to DP++ display bridge"
+ depends on OF
+ select DRM_KMS_HELPER
+ select DRM_PANEL
+ ---help---
+ This is a driver for the display bridge of
+ GE B850v3 that convert dual channel LVDS
+ to DP++. This is used with the i.MX6 imx-ldb
+ driver.
+
config DRM_NXP_PTN3460
tristate "NXP PTN3460 DP/LVDS bridge"
depends on OF
diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile
index 97ed1a5..b6b44a5 100644
--- a/drivers/gpu/drm/bridge/Makefile
+++ b/drivers/gpu/drm/bridge/Makefile
@@ -5,6 +5,7 @@ obj-$(CONFIG_DRM_DUMB_VGA_DAC) += dumb-vga-dac.o
obj-$(CONFIG_DRM_DW_HDMI) += dw-hdmi.o
obj-$(CONFIG_DRM_DW_HDMI_AHB_AUDIO) += dw-hdmi-ahb-audio.o
obj-$(CONFIG_DRM_NXP_PTN3460) += nxp-ptn3460.o
+obj-$(CONFIG_DRM_GE_B850V3_LVDS_DP) += ge_b850v3_lvds_dp.o
obj-$(CONFIG_DRM_PARADE_PS8622) += parade-ps8622.o
obj-$(CONFIG_DRM_SIL_SII8620) += sil-sii8620.o
obj-$(CONFIG_DRM_SII902X) += sii902x.o
diff --git a/drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c b/drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c
new file mode 100644
index 0000000..85875d8
--- /dev/null
+++ b/drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c
@@ -0,0 +1,395 @@
+/*
+ * Driver for GE B850v3 DP display bridge
+
+ * Copyright (c) 2016, Collabora Ltd.
+ * Copyright (c) 2016, General Electric Company
+
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+
+ * This driver creates a drm_bridge and a drm_connector for the LVDS to DP++
+ * display bridge of the GE B850v3. There are two physical bridges on the video
+ * signal pipeline: a STDP4028(LVDS to DP) and a STDP2690(DP to DP++). However
+ * the physical bridges are automatically configured by the input video signal,
+ * and the driver has no access to the video processing pipeline. The driver is
+ * only needed to read EDID from the STDP2690 and to handle HPD events from the
+ * STDP4028. The driver communicates with both bridges over i2c. The video
+ * signal pipeline is as follows:
+ *
+ * Host -> LVDS|--(STDP4028)--|DP -> DP|--(STDP2690)--|DP++ -> Video output
+ *
+ */
+
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <drm/drm_atomic.h>
+#include <drm/drm_atomic_helper.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_edid.h>
+#include <drm/drmP.h>
+
+/*
+ * 220Mhz is a limitation of the host, as the bridge is capable of up to
+ * 330Mhz. See section 9.2.1.2.4 of the i.MX 6Dual/6Quad Applications
+ * Processor Reference Manual for more information about the 220Mhz limit.
+ * The imx-ldb driver will warn about clocks over 170Mhz, but it seem to work
+ * fine.
+ */
+#define MAX_PIXEL_CLOCK 220000
+
+#define EDID_EXT_BLOCK_CNT 0x7E
+
+#define STDP4028_IRQ_OUT_CONF_REG 0x02
+#define STDP4028_DPTX_IRQ_EN_REG 0x3C
+#define STDP4028_DPTX_IRQ_STS_REG 0x3D
+#define STDP4028_DPTX_STS_REG 0x3E
+
+#define STDP4028_DPTX_DP_IRQ_EN 0x1000
+
+#define STDP4028_DPTX_HOTPLUG_IRQ_EN 0x0400
+#define STDP4028_DPTX_LINK_CH_IRQ_EN 0x2000
+#define STDP4028_DPTX_IRQ_CONFIG \
+ (STDP4028_DPTX_LINK_CH_IRQ_EN | STDP4028_DPTX_HOTPLUG_IRQ_EN)
+
+#define STDP4028_DPTX_HOTPLUG_STS 0x0200
+#define STDP4028_DPTX_LINK_STS 0x1000
+#define STDP4028_CON_STATE_CONNECTED \
+ (STDP4028_DPTX_HOTPLUG_STS | STDP4028_DPTX_LINK_STS)
+
+#define STDP4028_DPTX_HOTPLUG_CH_STS 0x0400
+#define STDP4028_DPTX_LINK_CH_STS 0x2000
+#define STDP4028_DPTX_IRQ_CLEAR \
+ (STDP4028_DPTX_LINK_CH_STS | STDP4028_DPTX_HOTPLUG_CH_STS)
+
+struct ge_b850v3_lvds_dp {
+ struct drm_connector connector;
+ struct drm_bridge bridge;
+ struct i2c_client *ge_b850v3_lvds_dp_i2c;
+ struct i2c_client *edid_i2c;
+ struct edid *edid;
+ struct mutex lock;
+};
+
+static inline struct ge_b850v3_lvds_dp *
+ bridge_to_ge_b850v3_lvds_dp(struct drm_bridge *bridge)
+{
+ return container_of(bridge, struct ge_b850v3_lvds_dp, bridge);
+}
+
+static inline struct ge_b850v3_lvds_dp *
+ connector_to_ge_b850v3_lvds_dp(struct drm_connector *connector)
+{
+ return container_of(connector, struct ge_b850v3_lvds_dp, connector);
+}
+
+u8 *stdp2690_get_edid(struct i2c_client *client)
+{
+ struct i2c_adapter *adapter = client->adapter;
+ unsigned char start = 0x00;
+ unsigned int total_size;
+ u8 *block = kmalloc(EDID_LENGTH, GFP_KERNEL);
+
+ struct i2c_msg msgs[] = {
+ {
+ .addr = client->addr,
+ .flags = 0,
+ .len = 1,
+ .buf = &start,
+ }, {
+ .addr = client->addr,
+ .flags = I2C_M_RD,
+ .len = EDID_LENGTH,
+ .buf = block,
+ }
+ };
+
+ if (!block)
+ return NULL;
+
+ if (i2c_transfer(adapter, msgs, 2) != 2) {
+ DRM_ERROR("Unable to read EDID.\n");
+ goto err;
+ }
+
+ if (!drm_edid_block_valid(block, 0, false, NULL)) {
+ DRM_ERROR("Invalid EDID block\n");
+ goto err;
+ }
+
+ total_size = (block[EDID_EXT_BLOCK_CNT] + 1) * EDID_LENGTH;
+ if (total_size > EDID_LENGTH) {
+ kfree(block);
+ block = kmalloc(total_size, GFP_KERNEL);
+ if (!block)
+ return NULL;
+
+ /* Yes, read the entire buffer, and do not skip the first
+ * EDID_LENGTH bytes.
+ */
+ start = 0x00;
+ msgs[1].len = total_size;
+ msgs[1].buf = block;
+
+ if (i2c_transfer(adapter, msgs, 2) != 2) {
+ DRM_ERROR("Unable to read EDID extension blocks.\n");
+ goto err;
+ }
+ }
+
+ return block;
+
+err:
+ kfree(block);
+ return NULL;
+}
+
+static int ge_b850v3_lvds_dp_get_modes(struct drm_connector *connector)
+{
+ struct ge_b850v3_lvds_dp *ptn_bridge;
+ struct i2c_client *client;
+ int num_modes = 0;
+
+ ptn_bridge = connector_to_ge_b850v3_lvds_dp(connector);
+ client = ptn_bridge->edid_i2c;
+
+ mutex_lock(&ptn_bridge->lock);
+
+ kfree(ptn_bridge->edid);
+ ptn_bridge->edid = (struct edid *) stdp2690_get_edid(client);
+
+ if (ptn_bridge->edid) {
+ drm_mode_connector_update_edid_property(connector,
+ ptn_bridge->edid);
+ num_modes = drm_add_edid_modes(connector, ptn_bridge->edid);
+ }
+
+ mutex_unlock(&ptn_bridge->lock);
+
+ return num_modes;
+}
+
+
+static enum drm_mode_status ge_b850v3_lvds_dp_mode_valid(
+ struct drm_connector *connector, struct drm_display_mode *mode)
+{
+ if (mode->clock > MAX_PIXEL_CLOCK) {
+ DRM_INFO("The pixel clock for the mode %s is too high, and not supported.",
+ mode->name);
+ return MODE_CLOCK_HIGH;
+ }
+
+ return MODE_OK;
+}
+
+static const struct
+drm_connector_helper_funcs ge_b850v3_lvds_dp_connector_helper_funcs = {
+ .get_modes = ge_b850v3_lvds_dp_get_modes,
+ .mode_valid = ge_b850v3_lvds_dp_mode_valid,
+};
+
+static enum drm_connector_status ge_b850v3_lvds_dp_detect(
+ struct drm_connector *connector, bool force)
+{
+ struct ge_b850v3_lvds_dp *ptn_bridge =
+ connector_to_ge_b850v3_lvds_dp(connector);
+ struct i2c_client *ge_b850v3_lvds_dp_i2c =
+ ptn_bridge->ge_b850v3_lvds_dp_i2c;
+ s32 link_state;
+
+ link_state = i2c_smbus_read_word_data(ge_b850v3_lvds_dp_i2c,
+ STDP4028_DPTX_STS_REG);
+
+ if (link_state == STDP4028_CON_STATE_CONNECTED)
+ return connector_status_connected;
+
+ if (link_state == 0)
+ return connector_status_disconnected;
+
+ return connector_status_unknown;
+}
+
+static const struct drm_connector_funcs ge_b850v3_lvds_dp_connector_funcs = {
+ .dpms = drm_atomic_helper_connector_dpms,
+ .fill_modes = drm_helper_probe_single_connector_modes,
+ .detect = ge_b850v3_lvds_dp_detect,
+ .destroy = drm_connector_cleanup,
+ .reset = drm_atomic_helper_connector_reset,
+ .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
+ .atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
+};
+
+static irqreturn_t ge_b850v3_lvds_dp_irq_handler(int irq, void *dev_id)
+{
+ struct ge_b850v3_lvds_dp *ptn_bridge = dev_id;
+ struct i2c_client *ge_b850v3_lvds_dp_i2c
+ = ptn_bridge->ge_b850v3_lvds_dp_i2c;
+
+ mutex_lock(&ptn_bridge->lock);
+
+ i2c_smbus_write_word_data(ge_b850v3_lvds_dp_i2c,
+ STDP4028_DPTX_IRQ_STS_REG, STDP4028_DPTX_IRQ_CLEAR);
+
+ mutex_unlock(&ptn_bridge->lock);
+
+ if (ptn_bridge->connector.dev)
+ drm_kms_helper_hotplug_event(ptn_bridge->connector.dev);
+
+ return IRQ_HANDLED;
+}
+
+static int ge_b850v3_lvds_dp_attach(struct drm_bridge *bridge)
+{
+ struct ge_b850v3_lvds_dp *ptn_bridge
+ = bridge_to_ge_b850v3_lvds_dp(bridge);
+ struct drm_connector *connector = &ptn_bridge->connector;
+ struct i2c_client *ge_b850v3_lvds_dp_i2c
+ = ptn_bridge->ge_b850v3_lvds_dp_i2c;
+ int ret;
+
+ if (!bridge->encoder) {
+ DRM_ERROR("Parent encoder object not found");
+ return -ENODEV;
+ }
+
+ connector->polled = DRM_CONNECTOR_POLL_HPD;
+
+ drm_connector_helper_add(connector,
+ &ge_b850v3_lvds_dp_connector_helper_funcs);
+
+ ret = drm_connector_init(bridge->dev, connector,
+ &ge_b850v3_lvds_dp_connector_funcs,
+ DRM_MODE_CONNECTOR_DisplayPort);
+ if (ret) {
+ DRM_ERROR("Failed to initialize connector with drm\n");
+ return ret;
+ }
+
+ ret = drm_mode_connector_attach_encoder(connector, bridge->encoder);
+ if (ret)
+ return ret;
+
+ /* Configures the bridge to re-enable interrupts after each ack. */
+ i2c_smbus_write_word_data(ge_b850v3_lvds_dp_i2c,
+ STDP4028_IRQ_OUT_CONF_REG, STDP4028_DPTX_DP_IRQ_EN);
+
+ /* Enable interrupts */
+ i2c_smbus_write_word_data(ge_b850v3_lvds_dp_i2c,
+ STDP4028_DPTX_IRQ_EN_REG, STDP4028_DPTX_IRQ_CONFIG);
+
+ return 0;
+}
+
+static const struct drm_bridge_funcs ge_b850v3_lvds_dp_funcs = {
+ .attach = ge_b850v3_lvds_dp_attach,
+};
+
+static int ge_b850v3_lvds_dp_probe(struct i2c_client *ge_b850v3_lvds_dp_i2c,
+ const struct i2c_device_id *id)
+{
+ struct device *dev = &ge_b850v3_lvds_dp_i2c->dev;
+ struct ge_b850v3_lvds_dp *ptn_bridge;
+ int ret;
+ u32 edid_i2c_reg;
+
+ ptn_bridge = devm_kzalloc(dev, sizeof(*ptn_bridge), GFP_KERNEL);
+ if (!ptn_bridge)
+ return -ENOMEM;
+
+ mutex_init(&ptn_bridge->lock);
+
+ ptn_bridge->ge_b850v3_lvds_dp_i2c = ge_b850v3_lvds_dp_i2c;
+ ptn_bridge->bridge.driver_private = ptn_bridge;
+ i2c_set_clientdata(ge_b850v3_lvds_dp_i2c, ptn_bridge);
+
+ ret = of_property_read_u32(dev->of_node, "edid-reg", &edid_i2c_reg);
+ if (ret) {
+ dev_err(dev, "edid-reg not specified, aborting...\n");
+ return -ENODEV;
+ }
+
+ ptn_bridge->edid_i2c = devm_kzalloc(dev,
+ sizeof(struct i2c_client), GFP_KERNEL);
+
+ if (!ptn_bridge->edid_i2c)
+ return -ENOMEM;
+
+ memcpy(ptn_bridge->edid_i2c, ge_b850v3_lvds_dp_i2c,
+ sizeof(struct i2c_client));
+
+ ptn_bridge->edid_i2c->addr = (unsigned short) edid_i2c_reg;
+
+ ptn_bridge->bridge.funcs = &ge_b850v3_lvds_dp_funcs;
+ ptn_bridge->bridge.of_node = dev->of_node;
+ ret = drm_bridge_add(&ptn_bridge->bridge);
+ if (ret) {
+ DRM_ERROR("Failed to add bridge\n");
+ return ret;
+ }
+
+ /* Clear pending interrupts since power up. */
+ i2c_smbus_write_word_data(ge_b850v3_lvds_dp_i2c,
+ STDP4028_DPTX_IRQ_STS_REG, STDP4028_DPTX_IRQ_CLEAR);
+
+ if (ge_b850v3_lvds_dp_i2c->irq) {
+ ret = devm_request_threaded_irq(&ge_b850v3_lvds_dp_i2c->dev,
+ ge_b850v3_lvds_dp_i2c->irq, NULL,
+ ge_b850v3_lvds_dp_irq_handler,
+ IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
+ "ge-b850v3-lvds-dp", ptn_bridge);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+static int ge_b850v3_lvds_dp_remove(struct i2c_client *ge_b850v3_lvds_dp_i2c)
+{
+ struct ge_b850v3_lvds_dp *ptn_bridge =
+ i2c_get_clientdata(ge_b850v3_lvds_dp_i2c);
+
+ drm_bridge_remove(&ptn_bridge->bridge);
+
+ kfree(ptn_bridge->edid);
+
+ return 0;
+}
+
+static const struct i2c_device_id ge_b850v3_lvds_dp_i2c_table[] = {
+ {"b850v3-lvds-dp", 0},
+ {},
+};
+MODULE_DEVICE_TABLE(i2c, ge_b850v3_lvds_dp_i2c_table);
+
+static const struct of_device_id ge_b850v3_lvds_dp_match[] = {
+ { .compatible = "ge,b850v3-lvds-dp" },
+ {},
+};
+MODULE_DEVICE_TABLE(of, ge_b850v3_lvds_dp_match);
+
+static struct i2c_driver ge_b850v3_lvds_dp_driver = {
+ .id_table = ge_b850v3_lvds_dp_i2c_table,
+ .probe = ge_b850v3_lvds_dp_probe,
+ .remove = ge_b850v3_lvds_dp_remove,
+ .driver = {
+ .name = "b850v3-lvds-dp",
+ .of_match_table = ge_b850v3_lvds_dp_match,
+ },
+};
+module_i2c_driver(ge_b850v3_lvds_dp_driver);
+
+MODULE_AUTHOR("Peter Senna Tschudin <peter.senna@collabora.com>");
+MODULE_AUTHOR("Martyn Welch <martyn.welch@collabora.co.uk>");
+MODULE_DESCRIPTION("GE LVDS to DP++ display bridge)");
+MODULE_LICENSE("GPL v2");
--
2.5.5
^ permalink raw reply related [flat|nested] 17+ messages in thread* [PATCH V6 3/4] drm/bridge: Add driver for GE B850v3 LVDS/DP++ Bridge
@ 2016-11-01 11:39 ` Philipp Zabel
0 siblings, 0 replies; 17+ messages in thread
From: Philipp Zabel @ 2016-11-01 11:39 UTC (permalink / raw)
To: linux-arm-kernel
Hi Peter,
Am Donnerstag, den 27.10.2016, 15:01 +0200 schrieb Peter Senna Tschudin:
> Add a driver that create a drm_bridge and a drm_connector for the LVDS
> to DP++ display bridge of the GE B850v3.
>
> There are two physical bridges on the video signal pipeline: a
> STDP4028(LVDS to DP) and a STDP2690(DP to DP++). The hardware and
> firmware made it complicated for this binding to comprise two device
> tree nodes, as the design goal is to configure both bridges based on
> the LVDS signal, which leave the driver powerless to control the video
> processing pipeline. The two bridges behaves as a single bridge, and
> the driver is only needed for telling the host about EDID / HPD, and
> for giving the host powers to ack interrupts. The video signal pipeline
> is as follows:
>
> Host -> LVDS|--(STDP4028)--|DP -> DP|--(STDP2690)--|DP++ -> Video output
>
> Cc: Martyn Welch <martyn.welch@collabora.co.uk>
> Cc: Martin Donnelly <martin.donnelly@ge.com>
> Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
> Cc: Enric Balletbo i Serra <enric.balletbo@collabora.com>
> Cc: Philipp Zabel <p.zabel@pengutronix.de>
> Cc: Rob Herring <robh@kernel.org>
> Cc: Fabio Estevam <fabio.estevam@nxp.com>
> CC: David Airlie <airlied@linux.ie>
> CC: Thierry Reding <treding@nvidia.com>
> CC: Thierry Reding <thierry.reding@gmail.com>
> CC: Archit Taneja <architt@codeaurora.org>
> Reviewed-by: Enric Balletbo <enric.balletbo@collabora.com>
> Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
> ---
> Changes from V5:
> - Reworked interrupt handler initialization
> - Removed useless calls to: drm_connector_register(),
> drm_helper_hpd_irq_event(), and drm_bridge_enable()
>
> Changes from V4:
> - Renamed the i2c_driver.name from "ge,b850v3-lvds-dp" to "b850v3-lvds-dp" to
> remove the comma from the driver name
>
> Changes from V3:
> - 3/4 instead of 4/5
> - Tested on next-20160804
>
> Changes from V2:
> - Made it atomic to be applied on next-20160729 on top of Liu Ying changes
> that made imx-ldb atomic
>
> Changes from V1:
> - New commit message
> - Removed 3 empty entry points
> - Removed memory leak from ge_b850v3_lvds_dp_get_modes()
> - Added a lock for mode setting
> - Removed a few blank lines
> - Changed the order at Makefile and Kconfig
>
> drivers/gpu/drm/bridge/Kconfig | 11 +
> drivers/gpu/drm/bridge/Makefile | 1 +
> drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c | 395 +++++++++++++++++++++++++++++
> 3 files changed, 407 insertions(+)
> create mode 100644 drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c
>
> diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig
> index bd6acc8..1d02422 100644
> --- a/drivers/gpu/drm/bridge/Kconfig
> +++ b/drivers/gpu/drm/bridge/Kconfig
> @@ -39,6 +39,17 @@ config DRM_DW_HDMI_AHB_AUDIO
> Designware HDMI block. This is used in conjunction with
> the i.MX6 HDMI driver.
>
> +config DRM_GE_B850V3_LVDS_DP
> + tristate "GE B850v3 LVDS to DP++ display bridge"
> + depends on OF
> + select DRM_KMS_HELPER
> + select DRM_PANEL
> + ---help---
> + This is a driver for the display bridge of
> + GE B850v3 that convert dual channel LVDS
> + to DP++. This is used with the i.MX6 imx-ldb
> + driver.
> +
> config DRM_NXP_PTN3460
> tristate "NXP PTN3460 DP/LVDS bridge"
> depends on OF
> diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile
> index 97ed1a5..b6b44a5 100644
> --- a/drivers/gpu/drm/bridge/Makefile
> +++ b/drivers/gpu/drm/bridge/Makefile
> @@ -5,6 +5,7 @@ obj-$(CONFIG_DRM_DUMB_VGA_DAC) += dumb-vga-dac.o
> obj-$(CONFIG_DRM_DW_HDMI) += dw-hdmi.o
> obj-$(CONFIG_DRM_DW_HDMI_AHB_AUDIO) += dw-hdmi-ahb-audio.o
> obj-$(CONFIG_DRM_NXP_PTN3460) += nxp-ptn3460.o
> +obj-$(CONFIG_DRM_GE_B850V3_LVDS_DP) += ge_b850v3_lvds_dp.o
> obj-$(CONFIG_DRM_PARADE_PS8622) += parade-ps8622.o
> obj-$(CONFIG_DRM_SIL_SII8620) += sil-sii8620.o
> obj-$(CONFIG_DRM_SII902X) += sii902x.o
> diff --git a/drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c b/drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c
> new file mode 100644
> index 0000000..85875d8
> --- /dev/null
> +++ b/drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c
> @@ -0,0 +1,395 @@
> +/*
> + * Driver for GE B850v3 DP display bridge
> +
> + * Copyright (c) 2016, Collabora Ltd.
> + * Copyright (c) 2016, General Electric Company
> +
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms and conditions of the GNU General Public License,
> + * version 2, as published by the Free Software Foundation.
> +
> + * This program is distributed in the hope it will be useful, but WITHOUT
> + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
> + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
> + * more details.
> +
> + * You should have received a copy of the GNU General Public License
> + * along with this program. If not, see <http://www.gnu.org/licenses/>.
> +
> + * This driver creates a drm_bridge and a drm_connector for the LVDS to DP++
> + * display bridge of the GE B850v3. There are two physical bridges on the video
> + * signal pipeline: a STDP4028(LVDS to DP) and a STDP2690(DP to DP++). However
> + * the physical bridges are automatically configured by the input video signal,
> + * and the driver has no access to the video processing pipeline. The driver is
> + * only needed to read EDID from the STDP2690 and to handle HPD events from the
> + * STDP4028. The driver communicates with both bridges over i2c. The video
> + * signal pipeline is as follows:
> + *
> + * Host -> LVDS|--(STDP4028)--|DP -> DP|--(STDP2690)--|DP++ -> Video output
> + *
> + */
> +
> +#include <linux/gpio.h>
> +#include <linux/i2c.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <drm/drm_atomic.h>
> +#include <drm/drm_atomic_helper.h>
> +#include <drm/drm_crtc_helper.h>
> +#include <drm/drm_edid.h>
> +#include <drm/drmP.h>
> +
> +/*
> + * 220Mhz is a limitation of the host, as the bridge is capable of up to
> + * 330Mhz. See section 9.2.1.2.4 of the i.MX 6Dual/6Quad Applications
> + * Processor Reference Manual for more information about the 220Mhz limit.
> + * The imx-ldb driver will warn about clocks over 170Mhz, but it seem to work
> + * fine.
> + */
> +#define MAX_PIXEL_CLOCK 220000
That is a limitation of the IPU DI pixel clock rate if both DIs are
active. If only a single DI is active, this limit is 264 MHz on i.MX6Q.
The LDB pixel clock rate maximum is 170 MHz if only a single LDB channel
is active.
I currently see no way for the crtc and encoder code to have a say about
maximum pixel clocks when pruning the mode list in .fill_modes.
> +
> +#define EDID_EXT_BLOCK_CNT 0x7E
> +
> +#define STDP4028_IRQ_OUT_CONF_REG 0x02
> +#define STDP4028_DPTX_IRQ_EN_REG 0x3C
> +#define STDP4028_DPTX_IRQ_STS_REG 0x3D
> +#define STDP4028_DPTX_STS_REG 0x3E
> +
> +#define STDP4028_DPTX_DP_IRQ_EN 0x1000
> +
> +#define STDP4028_DPTX_HOTPLUG_IRQ_EN 0x0400
> +#define STDP4028_DPTX_LINK_CH_IRQ_EN 0x2000
> +#define STDP4028_DPTX_IRQ_CONFIG \
> + (STDP4028_DPTX_LINK_CH_IRQ_EN | STDP4028_DPTX_HOTPLUG_IRQ_EN)
> +
> +#define STDP4028_DPTX_HOTPLUG_STS 0x0200
> +#define STDP4028_DPTX_LINK_STS 0x1000
> +#define STDP4028_CON_STATE_CONNECTED \
> + (STDP4028_DPTX_HOTPLUG_STS | STDP4028_DPTX_LINK_STS)
> +
> +#define STDP4028_DPTX_HOTPLUG_CH_STS 0x0400
> +#define STDP4028_DPTX_LINK_CH_STS 0x2000
> +#define STDP4028_DPTX_IRQ_CLEAR \
> + (STDP4028_DPTX_LINK_CH_STS | STDP4028_DPTX_HOTPLUG_CH_STS)
> +
> +struct ge_b850v3_lvds_dp {
> + struct drm_connector connector;
> + struct drm_bridge bridge;
> + struct i2c_client *ge_b850v3_lvds_dp_i2c;
> + struct i2c_client *edid_i2c;
> + struct edid *edid;
> + struct mutex lock;
> +};
> +
> +static inline struct ge_b850v3_lvds_dp *
> + bridge_to_ge_b850v3_lvds_dp(struct drm_bridge *bridge)
> +{
> + return container_of(bridge, struct ge_b850v3_lvds_dp, bridge);
> +}
> +
> +static inline struct ge_b850v3_lvds_dp *
> + connector_to_ge_b850v3_lvds_dp(struct drm_connector *connector)
> +{
> + return container_of(connector, struct ge_b850v3_lvds_dp, connector);
> +}
> +
> +u8 *stdp2690_get_edid(struct i2c_client *client)
> +{
> + struct i2c_adapter *adapter = client->adapter;
> + unsigned char start = 0x00;
> + unsigned int total_size;
> + u8 *block = kmalloc(EDID_LENGTH, GFP_KERNEL);
> +
> + struct i2c_msg msgs[] = {
> + {
> + .addr = client->addr,
> + .flags = 0,
> + .len = 1,
> + .buf = &start,
> + }, {
> + .addr = client->addr,
> + .flags = I2C_M_RD,
> + .len = EDID_LENGTH,
> + .buf = block,
> + }
> + };
> +
> + if (!block)
> + return NULL;
> +
> + if (i2c_transfer(adapter, msgs, 2) != 2) {
> + DRM_ERROR("Unable to read EDID.\n");
> + goto err;
> + }
> +
> + if (!drm_edid_block_valid(block, 0, false, NULL)) {
> + DRM_ERROR("Invalid EDID block\n");
> + goto err;
> + }
> +
> + total_size = (block[EDID_EXT_BLOCK_CNT] + 1) * EDID_LENGTH;
> + if (total_size > EDID_LENGTH) {
> + kfree(block);
> + block = kmalloc(total_size, GFP_KERNEL);
> + if (!block)
> + return NULL;
> +
> + /* Yes, read the entire buffer, and do not skip the first
> + * EDID_LENGTH bytes.
> + */
> + start = 0x00;
> + msgs[1].len = total_size;
> + msgs[1].buf = block;
> +
> + if (i2c_transfer(adapter, msgs, 2) != 2) {
> + DRM_ERROR("Unable to read EDID extension blocks.\n");
> + goto err;
> + }
> + }
> +
> + return block;
> +
> +err:
> + kfree(block);
> + return NULL;
> +}
> +
> +static int ge_b850v3_lvds_dp_get_modes(struct drm_connector *connector)
> +{
> + struct ge_b850v3_lvds_dp *ptn_bridge;
> + struct i2c_client *client;
> + int num_modes = 0;
> +
> + ptn_bridge = connector_to_ge_b850v3_lvds_dp(connector);
> + client = ptn_bridge->edid_i2c;
> +
> + mutex_lock(&ptn_bridge->lock);
What does this lock protect?
> + kfree(ptn_bridge->edid);
> + ptn_bridge->edid = (struct edid *) stdp2690_get_edid(client);
> +
> + if (ptn_bridge->edid) {
> + drm_mode_connector_update_edid_property(connector,
> + ptn_bridge->edid);
> + num_modes = drm_add_edid_modes(connector, ptn_bridge->edid);
> + }
> +
> + mutex_unlock(&ptn_bridge->lock);
> +
> + return num_modes;
> +}
> +
> +
> +static enum drm_mode_status ge_b850v3_lvds_dp_mode_valid(
> + struct drm_connector *connector, struct drm_display_mode *mode)
> +{
> + if (mode->clock > MAX_PIXEL_CLOCK) {
> + DRM_INFO("The pixel clock for the mode %s is too high, and not supported.",
> + mode->name);
> + return MODE_CLOCK_HIGH;
> + }
> +
> + return MODE_OK;
> +}
> +
> +static const struct
> +drm_connector_helper_funcs ge_b850v3_lvds_dp_connector_helper_funcs = {
> + .get_modes = ge_b850v3_lvds_dp_get_modes,
> + .mode_valid = ge_b850v3_lvds_dp_mode_valid,
> +};
> +
> +static enum drm_connector_status ge_b850v3_lvds_dp_detect(
> + struct drm_connector *connector, bool force)
> +{
> + struct ge_b850v3_lvds_dp *ptn_bridge =
> + connector_to_ge_b850v3_lvds_dp(connector);
> + struct i2c_client *ge_b850v3_lvds_dp_i2c =
> + ptn_bridge->ge_b850v3_lvds_dp_i2c;
> + s32 link_state;
> +
> + link_state = i2c_smbus_read_word_data(ge_b850v3_lvds_dp_i2c,
> + STDP4028_DPTX_STS_REG);
> +
> + if (link_state == STDP4028_CON_STATE_CONNECTED)
> + return connector_status_connected;
> +
> + if (link_state == 0)
> + return connector_status_disconnected;
> +
> + return connector_status_unknown;
> +}
> +
> +static const struct drm_connector_funcs ge_b850v3_lvds_dp_connector_funcs = {
> + .dpms = drm_atomic_helper_connector_dpms,
> + .fill_modes = drm_helper_probe_single_connector_modes,
> + .detect = ge_b850v3_lvds_dp_detect,
> + .destroy = drm_connector_cleanup,
> + .reset = drm_atomic_helper_connector_reset,
> + .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
> + .atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
> +};
> +
> +static irqreturn_t ge_b850v3_lvds_dp_irq_handler(int irq, void *dev_id)
> +{
> + struct ge_b850v3_lvds_dp *ptn_bridge = dev_id;
> + struct i2c_client *ge_b850v3_lvds_dp_i2c
> + = ptn_bridge->ge_b850v3_lvds_dp_i2c;
> +
> + mutex_lock(&ptn_bridge->lock);
And what does this lock protect here?
> + i2c_smbus_write_word_data(ge_b850v3_lvds_dp_i2c,
> + STDP4028_DPTX_IRQ_STS_REG, STDP4028_DPTX_IRQ_CLEAR);
> +
> + mutex_unlock(&ptn_bridge->lock);
> +
> + if (ptn_bridge->connector.dev)
> + drm_kms_helper_hotplug_event(ptn_bridge->connector.dev);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static int ge_b850v3_lvds_dp_attach(struct drm_bridge *bridge)
> +{
> + struct ge_b850v3_lvds_dp *ptn_bridge
> + = bridge_to_ge_b850v3_lvds_dp(bridge);
> + struct drm_connector *connector = &ptn_bridge->connector;
> + struct i2c_client *ge_b850v3_lvds_dp_i2c
> + = ptn_bridge->ge_b850v3_lvds_dp_i2c;
> + int ret;
> +
> + if (!bridge->encoder) {
> + DRM_ERROR("Parent encoder object not found");
> + return -ENODEV;
> + }
> +
> + connector->polled = DRM_CONNECTOR_POLL_HPD;
> +
> + drm_connector_helper_add(connector,
> + &ge_b850v3_lvds_dp_connector_helper_funcs);
> +
> + ret = drm_connector_init(bridge->dev, connector,
> + &ge_b850v3_lvds_dp_connector_funcs,
> + DRM_MODE_CONNECTOR_DisplayPort);
> + if (ret) {
> + DRM_ERROR("Failed to initialize connector with drm\n");
> + return ret;
> + }
> +
> + ret = drm_mode_connector_attach_encoder(connector, bridge->encoder);
> + if (ret)
> + return ret;
> +
> + /* Configures the bridge to re-enable interrupts after each ack. */
> + i2c_smbus_write_word_data(ge_b850v3_lvds_dp_i2c,
> + STDP4028_IRQ_OUT_CONF_REG, STDP4028_DPTX_DP_IRQ_EN);
> +
> + /* Enable interrupts */
> + i2c_smbus_write_word_data(ge_b850v3_lvds_dp_i2c,
> + STDP4028_DPTX_IRQ_EN_REG, STDP4028_DPTX_IRQ_CONFIG);
> +
> + return 0;
> +}
> +
> +static const struct drm_bridge_funcs ge_b850v3_lvds_dp_funcs = {
> + .attach = ge_b850v3_lvds_dp_attach,
What about .detach? Should the interrupt be disabled?
> +};
> +
> +static int ge_b850v3_lvds_dp_probe(struct i2c_client *ge_b850v3_lvds_dp_i2c,
> + const struct i2c_device_id *id)
> +{
> + struct device *dev = &ge_b850v3_lvds_dp_i2c->dev;
> + struct ge_b850v3_lvds_dp *ptn_bridge;
> + int ret;
> + u32 edid_i2c_reg;
> +
> + ptn_bridge = devm_kzalloc(dev, sizeof(*ptn_bridge), GFP_KERNEL);
> + if (!ptn_bridge)
> + return -ENOMEM;
> +
> + mutex_init(&ptn_bridge->lock);
> +
> + ptn_bridge->ge_b850v3_lvds_dp_i2c = ge_b850v3_lvds_dp_i2c;
> + ptn_bridge->bridge.driver_private = ptn_bridge;
> + i2c_set_clientdata(ge_b850v3_lvds_dp_i2c, ptn_bridge);
> +
> + ret = of_property_read_u32(dev->of_node, "edid-reg", &edid_i2c_reg);
> + if (ret) {
> + dev_err(dev, "edid-reg not specified, aborting...\n");
> + return -ENODEV;
> + }
> +
> + ptn_bridge->edid_i2c = devm_kzalloc(dev,
> + sizeof(struct i2c_client), GFP_KERNEL);
> +
Superfluous empty line, but ...
> + if (!ptn_bridge->edid_i2c)
> + return -ENOMEM;
> +
> + memcpy(ptn_bridge->edid_i2c, ge_b850v3_lvds_dp_i2c,
> + sizeof(struct i2c_client));
> +
> + ptn_bridge->edid_i2c->addr = (unsigned short) edid_i2c_reg;
... this looks to me like you should use i2c_new_dummy, or rather
i2c_new_secondary_device instead. For the latter you'd have to change
the bindings to use reg and reg-names properties instead of the custom
edid-reg property.
> +
> + ptn_bridge->bridge.funcs = &ge_b850v3_lvds_dp_funcs;
> + ptn_bridge->bridge.of_node = dev->of_node;
> + ret = drm_bridge_add(&ptn_bridge->bridge);
> + if (ret) {
> + DRM_ERROR("Failed to add bridge\n");
> + return ret;
> + }
Just as a note, this currently can not fail. It's just a list_add_tail
under a mutex lock.
If it would fail though, it'd be nice to also print the error code.
> +
> + /* Clear pending interrupts since power up. */
> + i2c_smbus_write_word_data(ge_b850v3_lvds_dp_i2c,
> + STDP4028_DPTX_IRQ_STS_REG, STDP4028_DPTX_IRQ_CLEAR);
> +
> + if (ge_b850v3_lvds_dp_i2c->irq) {
> + ret = devm_request_threaded_irq(&ge_b850v3_lvds_dp_i2c->dev,
> + ge_b850v3_lvds_dp_i2c->irq, NULL,
> + ge_b850v3_lvds_dp_irq_handler,
> + IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
> + "ge-b850v3-lvds-dp", ptn_bridge);
> + if (ret)
> + return ret;
> + }
> +
> + return 0;
Maybe a matter of taste, but this could be changed to:
/* If no interrupt has to be requested, we're done here */
if (!ge_b850v3_lvds_dp_i2c->irq)
return 0;
return devm_request_threaded_irq(&ge_b850v3_lvds_dp_i2c->dev,
ge_b850v3_lvds_dp_i2c->irq, NULL,
ge_b850v3_lvds_dp_irq_handler,
IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
"ge-b850v3-lvds-dp", ptn_bridge);
or, as we know ret to be 0 after the call to drm_bridge_add:
if (ge_b850v3_lvds_dp_i2c->irq) {
ret = devm_request_threaded_irq(&ge_b850v3_lvds_dp_i2c->dev,
ge_b850v3_lvds_dp_i2c->irq, NULL,
ge_b850v3_lvds_dp_irq_handler,
IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
"ge-b850v3-lvds-dp", ptn_bridge);
}
return ret;
> +}
> +
> +static int ge_b850v3_lvds_dp_remove(struct i2c_client *ge_b850v3_lvds_dp_i2c)
> +{
> + struct ge_b850v3_lvds_dp *ptn_bridge =
> + i2c_get_clientdata(ge_b850v3_lvds_dp_i2c);
> +
> + drm_bridge_remove(&ptn_bridge->bridge);
> +
> + kfree(ptn_bridge->edid);
> +
> + return 0;
> +}
> +
> +static const struct i2c_device_id ge_b850v3_lvds_dp_i2c_table[] = {
> + {"b850v3-lvds-dp", 0},
> + {},
> +};
> +MODULE_DEVICE_TABLE(i2c, ge_b850v3_lvds_dp_i2c_table);
> +
> +static const struct of_device_id ge_b850v3_lvds_dp_match[] = {
> + { .compatible = "ge,b850v3-lvds-dp" },
> + {},
> +};
> +MODULE_DEVICE_TABLE(of, ge_b850v3_lvds_dp_match);
> +
> +static struct i2c_driver ge_b850v3_lvds_dp_driver = {
> + .id_table = ge_b850v3_lvds_dp_i2c_table,
> + .probe = ge_b850v3_lvds_dp_probe,
> + .remove = ge_b850v3_lvds_dp_remove,
> + .driver = {
> + .name = "b850v3-lvds-dp",
> + .of_match_table = ge_b850v3_lvds_dp_match,
> + },
> +};
> +module_i2c_driver(ge_b850v3_lvds_dp_driver);
> +
> +MODULE_AUTHOR("Peter Senna Tschudin <peter.senna@collabora.com>");
> +MODULE_AUTHOR("Martyn Welch <martyn.welch@collabora.co.uk>");
> +MODULE_DESCRIPTION("GE LVDS to DP++ display bridge)");
> +MODULE_LICENSE("GPL v2");
regards
Philipp
^ permalink raw reply [flat|nested] 17+ messages in thread* Re: [PATCH V6 3/4] drm/bridge: Add driver for GE B850v3 LVDS/DP++ Bridge
@ 2016-11-01 11:39 ` Philipp Zabel
0 siblings, 0 replies; 17+ messages in thread
From: Philipp Zabel @ 2016-11-01 11:39 UTC (permalink / raw)
To: Peter Senna Tschudin
Cc: airlied, architt, akpm, daniel.vetter, davem, devicetree,
dri-devel, enric.balletbo, eballetbo, galak, gregkh, heiko,
ijc+devicetree, javier, jslaby, kernel, linux-arm-kernel, linux,
linux-kernel, linux, mark.rutland, martin.donnelly, martyn.welch,
mchehab, pawel.moll, peter.senna, thierry.reding, rmk+kernel,
robh+dt, shawnguo, tiwai, treding, ykk, Rob Herring,
Fabio Estevam
Hi Peter,
Am Donnerstag, den 27.10.2016, 15:01 +0200 schrieb Peter Senna Tschudin:
> Add a driver that create a drm_bridge and a drm_connector for the LVDS
> to DP++ display bridge of the GE B850v3.
>
> There are two physical bridges on the video signal pipeline: a
> STDP4028(LVDS to DP) and a STDP2690(DP to DP++). The hardware and
> firmware made it complicated for this binding to comprise two device
> tree nodes, as the design goal is to configure both bridges based on
> the LVDS signal, which leave the driver powerless to control the video
> processing pipeline. The two bridges behaves as a single bridge, and
> the driver is only needed for telling the host about EDID / HPD, and
> for giving the host powers to ack interrupts. The video signal pipeline
> is as follows:
>
> Host -> LVDS|--(STDP4028)--|DP -> DP|--(STDP2690)--|DP++ -> Video output
>
> Cc: Martyn Welch <martyn.welch@collabora.co.uk>
> Cc: Martin Donnelly <martin.donnelly@ge.com>
> Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
> Cc: Enric Balletbo i Serra <enric.balletbo@collabora.com>
> Cc: Philipp Zabel <p.zabel@pengutronix.de>
> Cc: Rob Herring <robh@kernel.org>
> Cc: Fabio Estevam <fabio.estevam@nxp.com>
> CC: David Airlie <airlied@linux.ie>
> CC: Thierry Reding <treding@nvidia.com>
> CC: Thierry Reding <thierry.reding@gmail.com>
> CC: Archit Taneja <architt@codeaurora.org>
> Reviewed-by: Enric Balletbo <enric.balletbo@collabora.com>
> Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
> ---
> Changes from V5:
> - Reworked interrupt handler initialization
> - Removed useless calls to: drm_connector_register(),
> drm_helper_hpd_irq_event(), and drm_bridge_enable()
>
> Changes from V4:
> - Renamed the i2c_driver.name from "ge,b850v3-lvds-dp" to "b850v3-lvds-dp" to
> remove the comma from the driver name
>
> Changes from V3:
> - 3/4 instead of 4/5
> - Tested on next-20160804
>
> Changes from V2:
> - Made it atomic to be applied on next-20160729 on top of Liu Ying changes
> that made imx-ldb atomic
>
> Changes from V1:
> - New commit message
> - Removed 3 empty entry points
> - Removed memory leak from ge_b850v3_lvds_dp_get_modes()
> - Added a lock for mode setting
> - Removed a few blank lines
> - Changed the order at Makefile and Kconfig
>
> drivers/gpu/drm/bridge/Kconfig | 11 +
> drivers/gpu/drm/bridge/Makefile | 1 +
> drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c | 395 +++++++++++++++++++++++++++++
> 3 files changed, 407 insertions(+)
> create mode 100644 drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c
>
> diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig
> index bd6acc8..1d02422 100644
> --- a/drivers/gpu/drm/bridge/Kconfig
> +++ b/drivers/gpu/drm/bridge/Kconfig
> @@ -39,6 +39,17 @@ config DRM_DW_HDMI_AHB_AUDIO
> Designware HDMI block. This is used in conjunction with
> the i.MX6 HDMI driver.
>
> +config DRM_GE_B850V3_LVDS_DP
> + tristate "GE B850v3 LVDS to DP++ display bridge"
> + depends on OF
> + select DRM_KMS_HELPER
> + select DRM_PANEL
> + ---help---
> + This is a driver for the display bridge of
> + GE B850v3 that convert dual channel LVDS
> + to DP++. This is used with the i.MX6 imx-ldb
> + driver.
> +
> config DRM_NXP_PTN3460
> tristate "NXP PTN3460 DP/LVDS bridge"
> depends on OF
> diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile
> index 97ed1a5..b6b44a5 100644
> --- a/drivers/gpu/drm/bridge/Makefile
> +++ b/drivers/gpu/drm/bridge/Makefile
> @@ -5,6 +5,7 @@ obj-$(CONFIG_DRM_DUMB_VGA_DAC) += dumb-vga-dac.o
> obj-$(CONFIG_DRM_DW_HDMI) += dw-hdmi.o
> obj-$(CONFIG_DRM_DW_HDMI_AHB_AUDIO) += dw-hdmi-ahb-audio.o
> obj-$(CONFIG_DRM_NXP_PTN3460) += nxp-ptn3460.o
> +obj-$(CONFIG_DRM_GE_B850V3_LVDS_DP) += ge_b850v3_lvds_dp.o
> obj-$(CONFIG_DRM_PARADE_PS8622) += parade-ps8622.o
> obj-$(CONFIG_DRM_SIL_SII8620) += sil-sii8620.o
> obj-$(CONFIG_DRM_SII902X) += sii902x.o
> diff --git a/drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c b/drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c
> new file mode 100644
> index 0000000..85875d8
> --- /dev/null
> +++ b/drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c
> @@ -0,0 +1,395 @@
> +/*
> + * Driver for GE B850v3 DP display bridge
> +
> + * Copyright (c) 2016, Collabora Ltd.
> + * Copyright (c) 2016, General Electric Company
> +
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms and conditions of the GNU General Public License,
> + * version 2, as published by the Free Software Foundation.
> +
> + * This program is distributed in the hope it will be useful, but WITHOUT
> + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
> + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
> + * more details.
> +
> + * You should have received a copy of the GNU General Public License
> + * along with this program. If not, see <http://www.gnu.org/licenses/>.
> +
> + * This driver creates a drm_bridge and a drm_connector for the LVDS to DP++
> + * display bridge of the GE B850v3. There are two physical bridges on the video
> + * signal pipeline: a STDP4028(LVDS to DP) and a STDP2690(DP to DP++). However
> + * the physical bridges are automatically configured by the input video signal,
> + * and the driver has no access to the video processing pipeline. The driver is
> + * only needed to read EDID from the STDP2690 and to handle HPD events from the
> + * STDP4028. The driver communicates with both bridges over i2c. The video
> + * signal pipeline is as follows:
> + *
> + * Host -> LVDS|--(STDP4028)--|DP -> DP|--(STDP2690)--|DP++ -> Video output
> + *
> + */
> +
> +#include <linux/gpio.h>
> +#include <linux/i2c.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <drm/drm_atomic.h>
> +#include <drm/drm_atomic_helper.h>
> +#include <drm/drm_crtc_helper.h>
> +#include <drm/drm_edid.h>
> +#include <drm/drmP.h>
> +
> +/*
> + * 220Mhz is a limitation of the host, as the bridge is capable of up to
> + * 330Mhz. See section 9.2.1.2.4 of the i.MX 6Dual/6Quad Applications
> + * Processor Reference Manual for more information about the 220Mhz limit.
> + * The imx-ldb driver will warn about clocks over 170Mhz, but it seem to work
> + * fine.
> + */
> +#define MAX_PIXEL_CLOCK 220000
That is a limitation of the IPU DI pixel clock rate if both DIs are
active. If only a single DI is active, this limit is 264 MHz on i.MX6Q.
The LDB pixel clock rate maximum is 170 MHz if only a single LDB channel
is active.
I currently see no way for the crtc and encoder code to have a say about
maximum pixel clocks when pruning the mode list in .fill_modes.
> +
> +#define EDID_EXT_BLOCK_CNT 0x7E
> +
> +#define STDP4028_IRQ_OUT_CONF_REG 0x02
> +#define STDP4028_DPTX_IRQ_EN_REG 0x3C
> +#define STDP4028_DPTX_IRQ_STS_REG 0x3D
> +#define STDP4028_DPTX_STS_REG 0x3E
> +
> +#define STDP4028_DPTX_DP_IRQ_EN 0x1000
> +
> +#define STDP4028_DPTX_HOTPLUG_IRQ_EN 0x0400
> +#define STDP4028_DPTX_LINK_CH_IRQ_EN 0x2000
> +#define STDP4028_DPTX_IRQ_CONFIG \
> + (STDP4028_DPTX_LINK_CH_IRQ_EN | STDP4028_DPTX_HOTPLUG_IRQ_EN)
> +
> +#define STDP4028_DPTX_HOTPLUG_STS 0x0200
> +#define STDP4028_DPTX_LINK_STS 0x1000
> +#define STDP4028_CON_STATE_CONNECTED \
> + (STDP4028_DPTX_HOTPLUG_STS | STDP4028_DPTX_LINK_STS)
> +
> +#define STDP4028_DPTX_HOTPLUG_CH_STS 0x0400
> +#define STDP4028_DPTX_LINK_CH_STS 0x2000
> +#define STDP4028_DPTX_IRQ_CLEAR \
> + (STDP4028_DPTX_LINK_CH_STS | STDP4028_DPTX_HOTPLUG_CH_STS)
> +
> +struct ge_b850v3_lvds_dp {
> + struct drm_connector connector;
> + struct drm_bridge bridge;
> + struct i2c_client *ge_b850v3_lvds_dp_i2c;
> + struct i2c_client *edid_i2c;
> + struct edid *edid;
> + struct mutex lock;
> +};
> +
> +static inline struct ge_b850v3_lvds_dp *
> + bridge_to_ge_b850v3_lvds_dp(struct drm_bridge *bridge)
> +{
> + return container_of(bridge, struct ge_b850v3_lvds_dp, bridge);
> +}
> +
> +static inline struct ge_b850v3_lvds_dp *
> + connector_to_ge_b850v3_lvds_dp(struct drm_connector *connector)
> +{
> + return container_of(connector, struct ge_b850v3_lvds_dp, connector);
> +}
> +
> +u8 *stdp2690_get_edid(struct i2c_client *client)
> +{
> + struct i2c_adapter *adapter = client->adapter;
> + unsigned char start = 0x00;
> + unsigned int total_size;
> + u8 *block = kmalloc(EDID_LENGTH, GFP_KERNEL);
> +
> + struct i2c_msg msgs[] = {
> + {
> + .addr = client->addr,
> + .flags = 0,
> + .len = 1,
> + .buf = &start,
> + }, {
> + .addr = client->addr,
> + .flags = I2C_M_RD,
> + .len = EDID_LENGTH,
> + .buf = block,
> + }
> + };
> +
> + if (!block)
> + return NULL;
> +
> + if (i2c_transfer(adapter, msgs, 2) != 2) {
> + DRM_ERROR("Unable to read EDID.\n");
> + goto err;
> + }
> +
> + if (!drm_edid_block_valid(block, 0, false, NULL)) {
> + DRM_ERROR("Invalid EDID block\n");
> + goto err;
> + }
> +
> + total_size = (block[EDID_EXT_BLOCK_CNT] + 1) * EDID_LENGTH;
> + if (total_size > EDID_LENGTH) {
> + kfree(block);
> + block = kmalloc(total_size, GFP_KERNEL);
> + if (!block)
> + return NULL;
> +
> + /* Yes, read the entire buffer, and do not skip the first
> + * EDID_LENGTH bytes.
> + */
> + start = 0x00;
> + msgs[1].len = total_size;
> + msgs[1].buf = block;
> +
> + if (i2c_transfer(adapter, msgs, 2) != 2) {
> + DRM_ERROR("Unable to read EDID extension blocks.\n");
> + goto err;
> + }
> + }
> +
> + return block;
> +
> +err:
> + kfree(block);
> + return NULL;
> +}
> +
> +static int ge_b850v3_lvds_dp_get_modes(struct drm_connector *connector)
> +{
> + struct ge_b850v3_lvds_dp *ptn_bridge;
> + struct i2c_client *client;
> + int num_modes = 0;
> +
> + ptn_bridge = connector_to_ge_b850v3_lvds_dp(connector);
> + client = ptn_bridge->edid_i2c;
> +
> + mutex_lock(&ptn_bridge->lock);
What does this lock protect?
> + kfree(ptn_bridge->edid);
> + ptn_bridge->edid = (struct edid *) stdp2690_get_edid(client);
> +
> + if (ptn_bridge->edid) {
> + drm_mode_connector_update_edid_property(connector,
> + ptn_bridge->edid);
> + num_modes = drm_add_edid_modes(connector, ptn_bridge->edid);
> + }
> +
> + mutex_unlock(&ptn_bridge->lock);
> +
> + return num_modes;
> +}
> +
> +
> +static enum drm_mode_status ge_b850v3_lvds_dp_mode_valid(
> + struct drm_connector *connector, struct drm_display_mode *mode)
> +{
> + if (mode->clock > MAX_PIXEL_CLOCK) {
> + DRM_INFO("The pixel clock for the mode %s is too high, and not supported.",
> + mode->name);
> + return MODE_CLOCK_HIGH;
> + }
> +
> + return MODE_OK;
> +}
> +
> +static const struct
> +drm_connector_helper_funcs ge_b850v3_lvds_dp_connector_helper_funcs = {
> + .get_modes = ge_b850v3_lvds_dp_get_modes,
> + .mode_valid = ge_b850v3_lvds_dp_mode_valid,
> +};
> +
> +static enum drm_connector_status ge_b850v3_lvds_dp_detect(
> + struct drm_connector *connector, bool force)
> +{
> + struct ge_b850v3_lvds_dp *ptn_bridge =
> + connector_to_ge_b850v3_lvds_dp(connector);
> + struct i2c_client *ge_b850v3_lvds_dp_i2c =
> + ptn_bridge->ge_b850v3_lvds_dp_i2c;
> + s32 link_state;
> +
> + link_state = i2c_smbus_read_word_data(ge_b850v3_lvds_dp_i2c,
> + STDP4028_DPTX_STS_REG);
> +
> + if (link_state == STDP4028_CON_STATE_CONNECTED)
> + return connector_status_connected;
> +
> + if (link_state == 0)
> + return connector_status_disconnected;
> +
> + return connector_status_unknown;
> +}
> +
> +static const struct drm_connector_funcs ge_b850v3_lvds_dp_connector_funcs = {
> + .dpms = drm_atomic_helper_connector_dpms,
> + .fill_modes = drm_helper_probe_single_connector_modes,
> + .detect = ge_b850v3_lvds_dp_detect,
> + .destroy = drm_connector_cleanup,
> + .reset = drm_atomic_helper_connector_reset,
> + .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
> + .atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
> +};
> +
> +static irqreturn_t ge_b850v3_lvds_dp_irq_handler(int irq, void *dev_id)
> +{
> + struct ge_b850v3_lvds_dp *ptn_bridge = dev_id;
> + struct i2c_client *ge_b850v3_lvds_dp_i2c
> + = ptn_bridge->ge_b850v3_lvds_dp_i2c;
> +
> + mutex_lock(&ptn_bridge->lock);
And what does this lock protect here?
> + i2c_smbus_write_word_data(ge_b850v3_lvds_dp_i2c,
> + STDP4028_DPTX_IRQ_STS_REG, STDP4028_DPTX_IRQ_CLEAR);
> +
> + mutex_unlock(&ptn_bridge->lock);
> +
> + if (ptn_bridge->connector.dev)
> + drm_kms_helper_hotplug_event(ptn_bridge->connector.dev);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static int ge_b850v3_lvds_dp_attach(struct drm_bridge *bridge)
> +{
> + struct ge_b850v3_lvds_dp *ptn_bridge
> + = bridge_to_ge_b850v3_lvds_dp(bridge);
> + struct drm_connector *connector = &ptn_bridge->connector;
> + struct i2c_client *ge_b850v3_lvds_dp_i2c
> + = ptn_bridge->ge_b850v3_lvds_dp_i2c;
> + int ret;
> +
> + if (!bridge->encoder) {
> + DRM_ERROR("Parent encoder object not found");
> + return -ENODEV;
> + }
> +
> + connector->polled = DRM_CONNECTOR_POLL_HPD;
> +
> + drm_connector_helper_add(connector,
> + &ge_b850v3_lvds_dp_connector_helper_funcs);
> +
> + ret = drm_connector_init(bridge->dev, connector,
> + &ge_b850v3_lvds_dp_connector_funcs,
> + DRM_MODE_CONNECTOR_DisplayPort);
> + if (ret) {
> + DRM_ERROR("Failed to initialize connector with drm\n");
> + return ret;
> + }
> +
> + ret = drm_mode_connector_attach_encoder(connector, bridge->encoder);
> + if (ret)
> + return ret;
> +
> + /* Configures the bridge to re-enable interrupts after each ack. */
> + i2c_smbus_write_word_data(ge_b850v3_lvds_dp_i2c,
> + STDP4028_IRQ_OUT_CONF_REG, STDP4028_DPTX_DP_IRQ_EN);
> +
> + /* Enable interrupts */
> + i2c_smbus_write_word_data(ge_b850v3_lvds_dp_i2c,
> + STDP4028_DPTX_IRQ_EN_REG, STDP4028_DPTX_IRQ_CONFIG);
> +
> + return 0;
> +}
> +
> +static const struct drm_bridge_funcs ge_b850v3_lvds_dp_funcs = {
> + .attach = ge_b850v3_lvds_dp_attach,
What about .detach? Should the interrupt be disabled?
> +};
> +
> +static int ge_b850v3_lvds_dp_probe(struct i2c_client *ge_b850v3_lvds_dp_i2c,
> + const struct i2c_device_id *id)
> +{
> + struct device *dev = &ge_b850v3_lvds_dp_i2c->dev;
> + struct ge_b850v3_lvds_dp *ptn_bridge;
> + int ret;
> + u32 edid_i2c_reg;
> +
> + ptn_bridge = devm_kzalloc(dev, sizeof(*ptn_bridge), GFP_KERNEL);
> + if (!ptn_bridge)
> + return -ENOMEM;
> +
> + mutex_init(&ptn_bridge->lock);
> +
> + ptn_bridge->ge_b850v3_lvds_dp_i2c = ge_b850v3_lvds_dp_i2c;
> + ptn_bridge->bridge.driver_private = ptn_bridge;
> + i2c_set_clientdata(ge_b850v3_lvds_dp_i2c, ptn_bridge);
> +
> + ret = of_property_read_u32(dev->of_node, "edid-reg", &edid_i2c_reg);
> + if (ret) {
> + dev_err(dev, "edid-reg not specified, aborting...\n");
> + return -ENODEV;
> + }
> +
> + ptn_bridge->edid_i2c = devm_kzalloc(dev,
> + sizeof(struct i2c_client), GFP_KERNEL);
> +
Superfluous empty line, but ...
> + if (!ptn_bridge->edid_i2c)
> + return -ENOMEM;
> +
> + memcpy(ptn_bridge->edid_i2c, ge_b850v3_lvds_dp_i2c,
> + sizeof(struct i2c_client));
> +
> + ptn_bridge->edid_i2c->addr = (unsigned short) edid_i2c_reg;
... this looks to me like you should use i2c_new_dummy, or rather
i2c_new_secondary_device instead. For the latter you'd have to change
the bindings to use reg and reg-names properties instead of the custom
edid-reg property.
> +
> + ptn_bridge->bridge.funcs = &ge_b850v3_lvds_dp_funcs;
> + ptn_bridge->bridge.of_node = dev->of_node;
> + ret = drm_bridge_add(&ptn_bridge->bridge);
> + if (ret) {
> + DRM_ERROR("Failed to add bridge\n");
> + return ret;
> + }
Just as a note, this currently can not fail. It's just a list_add_tail
under a mutex lock.
If it would fail though, it'd be nice to also print the error code.
> +
> + /* Clear pending interrupts since power up. */
> + i2c_smbus_write_word_data(ge_b850v3_lvds_dp_i2c,
> + STDP4028_DPTX_IRQ_STS_REG, STDP4028_DPTX_IRQ_CLEAR);
> +
> + if (ge_b850v3_lvds_dp_i2c->irq) {
> + ret = devm_request_threaded_irq(&ge_b850v3_lvds_dp_i2c->dev,
> + ge_b850v3_lvds_dp_i2c->irq, NULL,
> + ge_b850v3_lvds_dp_irq_handler,
> + IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
> + "ge-b850v3-lvds-dp", ptn_bridge);
> + if (ret)
> + return ret;
> + }
> +
> + return 0;
Maybe a matter of taste, but this could be changed to:
/* If no interrupt has to be requested, we're done here */
if (!ge_b850v3_lvds_dp_i2c->irq)
return 0;
return devm_request_threaded_irq(&ge_b850v3_lvds_dp_i2c->dev,
ge_b850v3_lvds_dp_i2c->irq, NULL,
ge_b850v3_lvds_dp_irq_handler,
IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
"ge-b850v3-lvds-dp", ptn_bridge);
or, as we know ret to be 0 after the call to drm_bridge_add:
if (ge_b850v3_lvds_dp_i2c->irq) {
ret = devm_request_threaded_irq(&ge_b850v3_lvds_dp_i2c->dev,
ge_b850v3_lvds_dp_i2c->irq, NULL,
ge_b850v3_lvds_dp_irq_handler,
IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
"ge-b850v3-lvds-dp", ptn_bridge);
}
return ret;
> +}
> +
> +static int ge_b850v3_lvds_dp_remove(struct i2c_client *ge_b850v3_lvds_dp_i2c)
> +{
> + struct ge_b850v3_lvds_dp *ptn_bridge =
> + i2c_get_clientdata(ge_b850v3_lvds_dp_i2c);
> +
> + drm_bridge_remove(&ptn_bridge->bridge);
> +
> + kfree(ptn_bridge->edid);
> +
> + return 0;
> +}
> +
> +static const struct i2c_device_id ge_b850v3_lvds_dp_i2c_table[] = {
> + {"b850v3-lvds-dp", 0},
> + {},
> +};
> +MODULE_DEVICE_TABLE(i2c, ge_b850v3_lvds_dp_i2c_table);
> +
> +static const struct of_device_id ge_b850v3_lvds_dp_match[] = {
> + { .compatible = "ge,b850v3-lvds-dp" },
> + {},
> +};
> +MODULE_DEVICE_TABLE(of, ge_b850v3_lvds_dp_match);
> +
> +static struct i2c_driver ge_b850v3_lvds_dp_driver = {
> + .id_table = ge_b850v3_lvds_dp_i2c_table,
> + .probe = ge_b850v3_lvds_dp_probe,
> + .remove = ge_b850v3_lvds_dp_remove,
> + .driver = {
> + .name = "b850v3-lvds-dp",
> + .of_match_table = ge_b850v3_lvds_dp_match,
> + },
> +};
> +module_i2c_driver(ge_b850v3_lvds_dp_driver);
> +
> +MODULE_AUTHOR("Peter Senna Tschudin <peter.senna@collabora.com>");
> +MODULE_AUTHOR("Martyn Welch <martyn.welch@collabora.co.uk>");
> +MODULE_DESCRIPTION("GE LVDS to DP++ display bridge)");
> +MODULE_LICENSE("GPL v2");
regards
Philipp
^ permalink raw reply [flat|nested] 17+ messages in thread* Re: [PATCH V6 3/4] drm/bridge: Add driver for GE B850v3 LVDS/DP++ Bridge
@ 2016-11-01 11:39 ` Philipp Zabel
0 siblings, 0 replies; 17+ messages in thread
From: Philipp Zabel @ 2016-11-01 11:39 UTC (permalink / raw)
To: Peter Senna Tschudin
Cc: airlied-cv59FeDIM0c, architt-sgV2jX0FEOL9JmXXK+q4OQ,
akpm-de/tnXTf+JLsfHDXvbKv3WD2FQJk+8+b, daniel.vetter-/w4YWyX8dFk,
davem-fT/PcQaiUtIeIZ0/mPfg9Q, devicetree-u79uwXL29TY76Z2rM5mHXA,
dri-devel-PD4FTy7X32lNgt0PjOBp9y5qC8QIuHrW,
enric.balletbo-ZGY8ohtN/8qB+jHODAdFcQ,
eballetbo-Re5JQEeQqe8AvxtiuMwx3w, galak-sgV2jX0FEOL9JmXXK+q4OQ,
gregkh-hQyY1W1yCW8ekmWlsbkhG0B+6BGkLq7r,
heiko-4mtYJXux2i+zQB+pC5nmwQ,
ijc+devicetree-KcIKpvwj1kUDXYZnReoRVg,
javier-0uQlZySMnqxg9hUCZPvPmw, jslaby-AlSwsSmVLrQ,
kernel-bIcnvbaLZ9MEGnE8C9+IrQ,
linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r,
linux-I+IVW8TIWO2tmTQ+vhA3Yw, linux-kernel-u79uwXL29TY76Z2rM5mHXA,
linux-0h96xk9xTtrk1uMJSBkQmQ, mark.rutland-5wv7dgnIgG8,
martin.donnelly-JJi787mZWgc, martyn.welch-ZGY8ohtN/8pPYcu2f3hruQ,
mchehab-JPH+aEBZ4P+UEJcrhfAQsw, pawel.moll-5wv7dgnIgG8,
peter.senna-Re5JQEeQqe8AvxtiuMwx3w,
thierry.reding-Re5JQEeQqe8AvxtiuMwx3w,
rmk+kernel-I+IVW8TIWO2tmTQ+vhA3Yw, robh+dt-DgEjT+Ai2ygdnm+yROfE0A,
shawnguo-DgEjT+Ai2ygdnm+yROfE0A, tiwai-IBi9RG/b67k,
treding-DDmLM1+adcrQT0dZR+AlfA, ykk
Hi Peter,
Am Donnerstag, den 27.10.2016, 15:01 +0200 schrieb Peter Senna Tschudin:
> Add a driver that create a drm_bridge and a drm_connector for the LVDS
> to DP++ display bridge of the GE B850v3.
>
> There are two physical bridges on the video signal pipeline: a
> STDP4028(LVDS to DP) and a STDP2690(DP to DP++). The hardware and
> firmware made it complicated for this binding to comprise two device
> tree nodes, as the design goal is to configure both bridges based on
> the LVDS signal, which leave the driver powerless to control the video
> processing pipeline. The two bridges behaves as a single bridge, and
> the driver is only needed for telling the host about EDID / HPD, and
> for giving the host powers to ack interrupts. The video signal pipeline
> is as follows:
>
> Host -> LVDS|--(STDP4028)--|DP -> DP|--(STDP2690)--|DP++ -> Video output
>
> Cc: Martyn Welch <martyn.welch-ZGY8ohtN/8pPYcu2f3hruQ@public.gmane.org>
> Cc: Martin Donnelly <martin.donnelly-JJi787mZWgc@public.gmane.org>
> Cc: Daniel Vetter <daniel.vetter-/w4YWyX8dFk@public.gmane.org>
> Cc: Enric Balletbo i Serra <enric.balletbo-ZGY8ohtN/8qB+jHODAdFcQ@public.gmane.org>
> Cc: Philipp Zabel <p.zabel-bIcnvbaLZ9MEGnE8C9+IrQ@public.gmane.org>
> Cc: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
> Cc: Fabio Estevam <fabio.estevam-3arQi8VN3Tc@public.gmane.org>
> CC: David Airlie <airlied-cv59FeDIM0c@public.gmane.org>
> CC: Thierry Reding <treding-DDmLM1+adcrQT0dZR+AlfA@public.gmane.org>
> CC: Thierry Reding <thierry.reding-Re5JQEeQqe8AvxtiuMwx3w@public.gmane.org>
> CC: Archit Taneja <architt-sgV2jX0FEOL9JmXXK+q4OQ@public.gmane.org>
> Reviewed-by: Enric Balletbo <enric.balletbo-ZGY8ohtN/8qB+jHODAdFcQ@public.gmane.org>
> Signed-off-by: Peter Senna Tschudin <peter.senna-ZGY8ohtN/8qB+jHODAdFcQ@public.gmane.org>
> ---
> Changes from V5:
> - Reworked interrupt handler initialization
> - Removed useless calls to: drm_connector_register(),
> drm_helper_hpd_irq_event(), and drm_bridge_enable()
>
> Changes from V4:
> - Renamed the i2c_driver.name from "ge,b850v3-lvds-dp" to "b850v3-lvds-dp" to
> remove the comma from the driver name
>
> Changes from V3:
> - 3/4 instead of 4/5
> - Tested on next-20160804
>
> Changes from V2:
> - Made it atomic to be applied on next-20160729 on top of Liu Ying changes
> that made imx-ldb atomic
>
> Changes from V1:
> - New commit message
> - Removed 3 empty entry points
> - Removed memory leak from ge_b850v3_lvds_dp_get_modes()
> - Added a lock for mode setting
> - Removed a few blank lines
> - Changed the order at Makefile and Kconfig
>
> drivers/gpu/drm/bridge/Kconfig | 11 +
> drivers/gpu/drm/bridge/Makefile | 1 +
> drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c | 395 +++++++++++++++++++++++++++++
> 3 files changed, 407 insertions(+)
> create mode 100644 drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c
>
> diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig
> index bd6acc8..1d02422 100644
> --- a/drivers/gpu/drm/bridge/Kconfig
> +++ b/drivers/gpu/drm/bridge/Kconfig
> @@ -39,6 +39,17 @@ config DRM_DW_HDMI_AHB_AUDIO
> Designware HDMI block. This is used in conjunction with
> the i.MX6 HDMI driver.
>
> +config DRM_GE_B850V3_LVDS_DP
> + tristate "GE B850v3 LVDS to DP++ display bridge"
> + depends on OF
> + select DRM_KMS_HELPER
> + select DRM_PANEL
> + ---help---
> + This is a driver for the display bridge of
> + GE B850v3 that convert dual channel LVDS
> + to DP++. This is used with the i.MX6 imx-ldb
> + driver.
> +
> config DRM_NXP_PTN3460
> tristate "NXP PTN3460 DP/LVDS bridge"
> depends on OF
> diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile
> index 97ed1a5..b6b44a5 100644
> --- a/drivers/gpu/drm/bridge/Makefile
> +++ b/drivers/gpu/drm/bridge/Makefile
> @@ -5,6 +5,7 @@ obj-$(CONFIG_DRM_DUMB_VGA_DAC) += dumb-vga-dac.o
> obj-$(CONFIG_DRM_DW_HDMI) += dw-hdmi.o
> obj-$(CONFIG_DRM_DW_HDMI_AHB_AUDIO) += dw-hdmi-ahb-audio.o
> obj-$(CONFIG_DRM_NXP_PTN3460) += nxp-ptn3460.o
> +obj-$(CONFIG_DRM_GE_B850V3_LVDS_DP) += ge_b850v3_lvds_dp.o
> obj-$(CONFIG_DRM_PARADE_PS8622) += parade-ps8622.o
> obj-$(CONFIG_DRM_SIL_SII8620) += sil-sii8620.o
> obj-$(CONFIG_DRM_SII902X) += sii902x.o
> diff --git a/drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c b/drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c
> new file mode 100644
> index 0000000..85875d8
> --- /dev/null
> +++ b/drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c
> @@ -0,0 +1,395 @@
> +/*
> + * Driver for GE B850v3 DP display bridge
> +
> + * Copyright (c) 2016, Collabora Ltd.
> + * Copyright (c) 2016, General Electric Company
> +
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms and conditions of the GNU General Public License,
> + * version 2, as published by the Free Software Foundation.
> +
> + * This program is distributed in the hope it will be useful, but WITHOUT
> + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
> + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
> + * more details.
> +
> + * You should have received a copy of the GNU General Public License
> + * along with this program. If not, see <http://www.gnu.org/licenses/>.
> +
> + * This driver creates a drm_bridge and a drm_connector for the LVDS to DP++
> + * display bridge of the GE B850v3. There are two physical bridges on the video
> + * signal pipeline: a STDP4028(LVDS to DP) and a STDP2690(DP to DP++). However
> + * the physical bridges are automatically configured by the input video signal,
> + * and the driver has no access to the video processing pipeline. The driver is
> + * only needed to read EDID from the STDP2690 and to handle HPD events from the
> + * STDP4028. The driver communicates with both bridges over i2c. The video
> + * signal pipeline is as follows:
> + *
> + * Host -> LVDS|--(STDP4028)--|DP -> DP|--(STDP2690)--|DP++ -> Video output
> + *
> + */
> +
> +#include <linux/gpio.h>
> +#include <linux/i2c.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <drm/drm_atomic.h>
> +#include <drm/drm_atomic_helper.h>
> +#include <drm/drm_crtc_helper.h>
> +#include <drm/drm_edid.h>
> +#include <drm/drmP.h>
> +
> +/*
> + * 220Mhz is a limitation of the host, as the bridge is capable of up to
> + * 330Mhz. See section 9.2.1.2.4 of the i.MX 6Dual/6Quad Applications
> + * Processor Reference Manual for more information about the 220Mhz limit.
> + * The imx-ldb driver will warn about clocks over 170Mhz, but it seem to work
> + * fine.
> + */
> +#define MAX_PIXEL_CLOCK 220000
That is a limitation of the IPU DI pixel clock rate if both DIs are
active. If only a single DI is active, this limit is 264 MHz on i.MX6Q.
The LDB pixel clock rate maximum is 170 MHz if only a single LDB channel
is active.
I currently see no way for the crtc and encoder code to have a say about
maximum pixel clocks when pruning the mode list in .fill_modes.
> +
> +#define EDID_EXT_BLOCK_CNT 0x7E
> +
> +#define STDP4028_IRQ_OUT_CONF_REG 0x02
> +#define STDP4028_DPTX_IRQ_EN_REG 0x3C
> +#define STDP4028_DPTX_IRQ_STS_REG 0x3D
> +#define STDP4028_DPTX_STS_REG 0x3E
> +
> +#define STDP4028_DPTX_DP_IRQ_EN 0x1000
> +
> +#define STDP4028_DPTX_HOTPLUG_IRQ_EN 0x0400
> +#define STDP4028_DPTX_LINK_CH_IRQ_EN 0x2000
> +#define STDP4028_DPTX_IRQ_CONFIG \
> + (STDP4028_DPTX_LINK_CH_IRQ_EN | STDP4028_DPTX_HOTPLUG_IRQ_EN)
> +
> +#define STDP4028_DPTX_HOTPLUG_STS 0x0200
> +#define STDP4028_DPTX_LINK_STS 0x1000
> +#define STDP4028_CON_STATE_CONNECTED \
> + (STDP4028_DPTX_HOTPLUG_STS | STDP4028_DPTX_LINK_STS)
> +
> +#define STDP4028_DPTX_HOTPLUG_CH_STS 0x0400
> +#define STDP4028_DPTX_LINK_CH_STS 0x2000
> +#define STDP4028_DPTX_IRQ_CLEAR \
> + (STDP4028_DPTX_LINK_CH_STS | STDP4028_DPTX_HOTPLUG_CH_STS)
> +
> +struct ge_b850v3_lvds_dp {
> + struct drm_connector connector;
> + struct drm_bridge bridge;
> + struct i2c_client *ge_b850v3_lvds_dp_i2c;
> + struct i2c_client *edid_i2c;
> + struct edid *edid;
> + struct mutex lock;
> +};
> +
> +static inline struct ge_b850v3_lvds_dp *
> + bridge_to_ge_b850v3_lvds_dp(struct drm_bridge *bridge)
> +{
> + return container_of(bridge, struct ge_b850v3_lvds_dp, bridge);
> +}
> +
> +static inline struct ge_b850v3_lvds_dp *
> + connector_to_ge_b850v3_lvds_dp(struct drm_connector *connector)
> +{
> + return container_of(connector, struct ge_b850v3_lvds_dp, connector);
> +}
> +
> +u8 *stdp2690_get_edid(struct i2c_client *client)
> +{
> + struct i2c_adapter *adapter = client->adapter;
> + unsigned char start = 0x00;
> + unsigned int total_size;
> + u8 *block = kmalloc(EDID_LENGTH, GFP_KERNEL);
> +
> + struct i2c_msg msgs[] = {
> + {
> + .addr = client->addr,
> + .flags = 0,
> + .len = 1,
> + .buf = &start,
> + }, {
> + .addr = client->addr,
> + .flags = I2C_M_RD,
> + .len = EDID_LENGTH,
> + .buf = block,
> + }
> + };
> +
> + if (!block)
> + return NULL;
> +
> + if (i2c_transfer(adapter, msgs, 2) != 2) {
> + DRM_ERROR("Unable to read EDID.\n");
> + goto err;
> + }
> +
> + if (!drm_edid_block_valid(block, 0, false, NULL)) {
> + DRM_ERROR("Invalid EDID block\n");
> + goto err;
> + }
> +
> + total_size = (block[EDID_EXT_BLOCK_CNT] + 1) * EDID_LENGTH;
> + if (total_size > EDID_LENGTH) {
> + kfree(block);
> + block = kmalloc(total_size, GFP_KERNEL);
> + if (!block)
> + return NULL;
> +
> + /* Yes, read the entire buffer, and do not skip the first
> + * EDID_LENGTH bytes.
> + */
> + start = 0x00;
> + msgs[1].len = total_size;
> + msgs[1].buf = block;
> +
> + if (i2c_transfer(adapter, msgs, 2) != 2) {
> + DRM_ERROR("Unable to read EDID extension blocks.\n");
> + goto err;
> + }
> + }
> +
> + return block;
> +
> +err:
> + kfree(block);
> + return NULL;
> +}
> +
> +static int ge_b850v3_lvds_dp_get_modes(struct drm_connector *connector)
> +{
> + struct ge_b850v3_lvds_dp *ptn_bridge;
> + struct i2c_client *client;
> + int num_modes = 0;
> +
> + ptn_bridge = connector_to_ge_b850v3_lvds_dp(connector);
> + client = ptn_bridge->edid_i2c;
> +
> + mutex_lock(&ptn_bridge->lock);
What does this lock protect?
> + kfree(ptn_bridge->edid);
> + ptn_bridge->edid = (struct edid *) stdp2690_get_edid(client);
> +
> + if (ptn_bridge->edid) {
> + drm_mode_connector_update_edid_property(connector,
> + ptn_bridge->edid);
> + num_modes = drm_add_edid_modes(connector, ptn_bridge->edid);
> + }
> +
> + mutex_unlock(&ptn_bridge->lock);
> +
> + return num_modes;
> +}
> +
> +
> +static enum drm_mode_status ge_b850v3_lvds_dp_mode_valid(
> + struct drm_connector *connector, struct drm_display_mode *mode)
> +{
> + if (mode->clock > MAX_PIXEL_CLOCK) {
> + DRM_INFO("The pixel clock for the mode %s is too high, and not supported.",
> + mode->name);
> + return MODE_CLOCK_HIGH;
> + }
> +
> + return MODE_OK;
> +}
> +
> +static const struct
> +drm_connector_helper_funcs ge_b850v3_lvds_dp_connector_helper_funcs = {
> + .get_modes = ge_b850v3_lvds_dp_get_modes,
> + .mode_valid = ge_b850v3_lvds_dp_mode_valid,
> +};
> +
> +static enum drm_connector_status ge_b850v3_lvds_dp_detect(
> + struct drm_connector *connector, bool force)
> +{
> + struct ge_b850v3_lvds_dp *ptn_bridge =
> + connector_to_ge_b850v3_lvds_dp(connector);
> + struct i2c_client *ge_b850v3_lvds_dp_i2c =
> + ptn_bridge->ge_b850v3_lvds_dp_i2c;
> + s32 link_state;
> +
> + link_state = i2c_smbus_read_word_data(ge_b850v3_lvds_dp_i2c,
> + STDP4028_DPTX_STS_REG);
> +
> + if (link_state == STDP4028_CON_STATE_CONNECTED)
> + return connector_status_connected;
> +
> + if (link_state == 0)
> + return connector_status_disconnected;
> +
> + return connector_status_unknown;
> +}
> +
> +static const struct drm_connector_funcs ge_b850v3_lvds_dp_connector_funcs = {
> + .dpms = drm_atomic_helper_connector_dpms,
> + .fill_modes = drm_helper_probe_single_connector_modes,
> + .detect = ge_b850v3_lvds_dp_detect,
> + .destroy = drm_connector_cleanup,
> + .reset = drm_atomic_helper_connector_reset,
> + .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
> + .atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
> +};
> +
> +static irqreturn_t ge_b850v3_lvds_dp_irq_handler(int irq, void *dev_id)
> +{
> + struct ge_b850v3_lvds_dp *ptn_bridge = dev_id;
> + struct i2c_client *ge_b850v3_lvds_dp_i2c
> + = ptn_bridge->ge_b850v3_lvds_dp_i2c;
> +
> + mutex_lock(&ptn_bridge->lock);
And what does this lock protect here?
> + i2c_smbus_write_word_data(ge_b850v3_lvds_dp_i2c,
> + STDP4028_DPTX_IRQ_STS_REG, STDP4028_DPTX_IRQ_CLEAR);
> +
> + mutex_unlock(&ptn_bridge->lock);
> +
> + if (ptn_bridge->connector.dev)
> + drm_kms_helper_hotplug_event(ptn_bridge->connector.dev);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static int ge_b850v3_lvds_dp_attach(struct drm_bridge *bridge)
> +{
> + struct ge_b850v3_lvds_dp *ptn_bridge
> + = bridge_to_ge_b850v3_lvds_dp(bridge);
> + struct drm_connector *connector = &ptn_bridge->connector;
> + struct i2c_client *ge_b850v3_lvds_dp_i2c
> + = ptn_bridge->ge_b850v3_lvds_dp_i2c;
> + int ret;
> +
> + if (!bridge->encoder) {
> + DRM_ERROR("Parent encoder object not found");
> + return -ENODEV;
> + }
> +
> + connector->polled = DRM_CONNECTOR_POLL_HPD;
> +
> + drm_connector_helper_add(connector,
> + &ge_b850v3_lvds_dp_connector_helper_funcs);
> +
> + ret = drm_connector_init(bridge->dev, connector,
> + &ge_b850v3_lvds_dp_connector_funcs,
> + DRM_MODE_CONNECTOR_DisplayPort);
> + if (ret) {
> + DRM_ERROR("Failed to initialize connector with drm\n");
> + return ret;
> + }
> +
> + ret = drm_mode_connector_attach_encoder(connector, bridge->encoder);
> + if (ret)
> + return ret;
> +
> + /* Configures the bridge to re-enable interrupts after each ack. */
> + i2c_smbus_write_word_data(ge_b850v3_lvds_dp_i2c,
> + STDP4028_IRQ_OUT_CONF_REG, STDP4028_DPTX_DP_IRQ_EN);
> +
> + /* Enable interrupts */
> + i2c_smbus_write_word_data(ge_b850v3_lvds_dp_i2c,
> + STDP4028_DPTX_IRQ_EN_REG, STDP4028_DPTX_IRQ_CONFIG);
> +
> + return 0;
> +}
> +
> +static const struct drm_bridge_funcs ge_b850v3_lvds_dp_funcs = {
> + .attach = ge_b850v3_lvds_dp_attach,
What about .detach? Should the interrupt be disabled?
> +};
> +
> +static int ge_b850v3_lvds_dp_probe(struct i2c_client *ge_b850v3_lvds_dp_i2c,
> + const struct i2c_device_id *id)
> +{
> + struct device *dev = &ge_b850v3_lvds_dp_i2c->dev;
> + struct ge_b850v3_lvds_dp *ptn_bridge;
> + int ret;
> + u32 edid_i2c_reg;
> +
> + ptn_bridge = devm_kzalloc(dev, sizeof(*ptn_bridge), GFP_KERNEL);
> + if (!ptn_bridge)
> + return -ENOMEM;
> +
> + mutex_init(&ptn_bridge->lock);
> +
> + ptn_bridge->ge_b850v3_lvds_dp_i2c = ge_b850v3_lvds_dp_i2c;
> + ptn_bridge->bridge.driver_private = ptn_bridge;
> + i2c_set_clientdata(ge_b850v3_lvds_dp_i2c, ptn_bridge);
> +
> + ret = of_property_read_u32(dev->of_node, "edid-reg", &edid_i2c_reg);
> + if (ret) {
> + dev_err(dev, "edid-reg not specified, aborting...\n");
> + return -ENODEV;
> + }
> +
> + ptn_bridge->edid_i2c = devm_kzalloc(dev,
> + sizeof(struct i2c_client), GFP_KERNEL);
> +
Superfluous empty line, but ...
> + if (!ptn_bridge->edid_i2c)
> + return -ENOMEM;
> +
> + memcpy(ptn_bridge->edid_i2c, ge_b850v3_lvds_dp_i2c,
> + sizeof(struct i2c_client));
> +
> + ptn_bridge->edid_i2c->addr = (unsigned short) edid_i2c_reg;
... this looks to me like you should use i2c_new_dummy, or rather
i2c_new_secondary_device instead. For the latter you'd have to change
the bindings to use reg and reg-names properties instead of the custom
edid-reg property.
> +
> + ptn_bridge->bridge.funcs = &ge_b850v3_lvds_dp_funcs;
> + ptn_bridge->bridge.of_node = dev->of_node;
> + ret = drm_bridge_add(&ptn_bridge->bridge);
> + if (ret) {
> + DRM_ERROR("Failed to add bridge\n");
> + return ret;
> + }
Just as a note, this currently can not fail. It's just a list_add_tail
under a mutex lock.
If it would fail though, it'd be nice to also print the error code.
> +
> + /* Clear pending interrupts since power up. */
> + i2c_smbus_write_word_data(ge_b850v3_lvds_dp_i2c,
> + STDP4028_DPTX_IRQ_STS_REG, STDP4028_DPTX_IRQ_CLEAR);
> +
> + if (ge_b850v3_lvds_dp_i2c->irq) {
> + ret = devm_request_threaded_irq(&ge_b850v3_lvds_dp_i2c->dev,
> + ge_b850v3_lvds_dp_i2c->irq, NULL,
> + ge_b850v3_lvds_dp_irq_handler,
> + IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
> + "ge-b850v3-lvds-dp", ptn_bridge);
> + if (ret)
> + return ret;
> + }
> +
> + return 0;
Maybe a matter of taste, but this could be changed to:
/* If no interrupt has to be requested, we're done here */
if (!ge_b850v3_lvds_dp_i2c->irq)
return 0;
return devm_request_threaded_irq(&ge_b850v3_lvds_dp_i2c->dev,
ge_b850v3_lvds_dp_i2c->irq, NULL,
ge_b850v3_lvds_dp_irq_handler,
IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
"ge-b850v3-lvds-dp", ptn_bridge);
or, as we know ret to be 0 after the call to drm_bridge_add:
if (ge_b850v3_lvds_dp_i2c->irq) {
ret = devm_request_threaded_irq(&ge_b850v3_lvds_dp_i2c->dev,
ge_b850v3_lvds_dp_i2c->irq, NULL,
ge_b850v3_lvds_dp_irq_handler,
IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
"ge-b850v3-lvds-dp", ptn_bridge);
}
return ret;
> +}
> +
> +static int ge_b850v3_lvds_dp_remove(struct i2c_client *ge_b850v3_lvds_dp_i2c)
> +{
> + struct ge_b850v3_lvds_dp *ptn_bridge =
> + i2c_get_clientdata(ge_b850v3_lvds_dp_i2c);
> +
> + drm_bridge_remove(&ptn_bridge->bridge);
> +
> + kfree(ptn_bridge->edid);
> +
> + return 0;
> +}
> +
> +static const struct i2c_device_id ge_b850v3_lvds_dp_i2c_table[] = {
> + {"b850v3-lvds-dp", 0},
> + {},
> +};
> +MODULE_DEVICE_TABLE(i2c, ge_b850v3_lvds_dp_i2c_table);
> +
> +static const struct of_device_id ge_b850v3_lvds_dp_match[] = {
> + { .compatible = "ge,b850v3-lvds-dp" },
> + {},
> +};
> +MODULE_DEVICE_TABLE(of, ge_b850v3_lvds_dp_match);
> +
> +static struct i2c_driver ge_b850v3_lvds_dp_driver = {
> + .id_table = ge_b850v3_lvds_dp_i2c_table,
> + .probe = ge_b850v3_lvds_dp_probe,
> + .remove = ge_b850v3_lvds_dp_remove,
> + .driver = {
> + .name = "b850v3-lvds-dp",
> + .of_match_table = ge_b850v3_lvds_dp_match,
> + },
> +};
> +module_i2c_driver(ge_b850v3_lvds_dp_driver);
> +
> +MODULE_AUTHOR("Peter Senna Tschudin <peter.senna-ZGY8ohtN/8qB+jHODAdFcQ@public.gmane.org>");
> +MODULE_AUTHOR("Martyn Welch <martyn.welch-ZGY8ohtN/8pPYcu2f3hruQ@public.gmane.org>");
> +MODULE_DESCRIPTION("GE LVDS to DP++ display bridge)");
> +MODULE_LICENSE("GPL v2");
regards
Philipp
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 17+ messages in thread