[PATCH v2 0/4] mmc: sdhci-cadence: SD6HC DDR50/DDR52 read-path tuning and fixes

[PATCH v2 0/4] mmc: sdhci-cadence: SD6HC DDR50/DDR52 read-path tuning and fixes

[tze.yee.ng]

From: Tze Yee Ng <tze.yee.ng@altera.com>

This series enables the extended-read DDR modes - SD DDR50 and eMMC
DDR52 - on the Cadence SD6HC (SD/eMMC v6) PHY. Neither mode runs a host
tuning sequence (CMD19/CMD21), so the read path must be centred by
static, board/SoC-characterised PHY settings. Bringing it up on Agilex5
also exposed PHY issues affecting the existing tuned modes.

  - Patch 1: settle the PHY once after the final tuning tap, before the
    first post-tuning command (an R1b CMD6 during HS400 selection can
    otherwise time out); matches sdhci_cdns6_phy_init().
  - Patch 2: program PHONY_DQS_TIMING (left 0 in all modes); in the
    extended-read DDR modes it must be the rebar pulse width in clk_phy
    cycles minus 1, else one DDR beat is duplicated.
  - Patch 3: document three optional SD6HC read-path properties for the
    extended-read DDR modes (SD DDR50, eMMC DDR52).
  - Patch 4: read those properties at probe and apply them in DDR50 and
    DDR52, and make the DQS_TIMING update clear USE_LPBK_DQS before
    reprogramming it so the loopback/phony selection takes effect.

The new cdns,ddr-* properties are unused in this series; they will be
consumed by the socfpga_agilex5_socdk and socfpga_agilex5_socdk_emmc
device trees, submitted as a separate series.

Tested on Agilex5 SoCDK: SD DDR50 and eMMC DDR52.

Changes in v2:
  - Patch 1: moved the 5 ms PHY settle out of the per-tap tuning loop to
    a single settle after the winning tap, on the success path only, and
    rewrote the comment to explain this specific call site. (Adrian
    Hunter, Tanmay Kathpalia)
  - Patch 2: added Adrian's Acked-by; reworded the commit message to drop
    the "generic to any SD6HC-PHY SoC" framing. (Adrian Hunter)
  - Patch 3: retitled to "dt-bindings: mmc: cdns,sd6hc:"; renamed
    cdns,ddr50-* -> cdns,ddr-*; cdns,ddr-read-dqs-delay-ps is now in
    picoseconds; replaced the read-DQS source selector with a
    cdns,ddr-no-lpbk-dqs boolean; reworded the phony-dqs-timing text;
    dropped the SD4HC note. (Krzysztof Kozlowski, Tanmay Kathpalia)
  - Patch 4: renamed the properties to cdns,ddr-*; read
    cdns,ddr-read-dqs-delay-ps in ps and convert it to delay elements
    (dividing by cdns,delay-element-ps), clamping that quotient to the
    8-bit PHY field so a small delay element cannot make it wrap; read
    cdns,ddr-no-lpbk-dqs via of_property_read_bool() to opt out of the
    default loopback DQS read path; dropped the v1 per-property range
    checks and redundant FIELD_MAX() write masks; apply the overrides in
    both DDR50 and DDR52. Also retitled to "mmc: sdhci-cadence6:" since it
    touches only the v6 PHY. (Krzysztof Kozlowski, Adrian Hunter,
    Tanmay Kathpalia)

Tze Yee Ng (4):
  mmc: sdhci-cadence: add PHY settle after tuning for SD6HC
  mmc: sdhci-cadence6: program PHONY_DQS_TIMING for extended-read DDR
  dt-bindings: mmc: cdns,sd6hc: add SD6HC DDR50 read-path tuning
  mmc: sdhci-cadence6: read SD6HC DDR50 tuning from device tree

 .../devicetree/bindings/mmc/cdns,sd6hc.yaml   | 30 ++++++++
 drivers/mmc/host/sdhci-cadence-core.c         |  6 +-
 drivers/mmc/host/sdhci-cadence-phy-v6.c       | 74 ++++++++++++++++++-
 3 files changed, 108 insertions(+), 2 deletions(-)


base-commit: 2d2431cf24dda7303d59e47b7d116be8beda66b1
-- 
2.43.7

[PATCH v2 1/4] mmc: sdhci-cadence: add PHY settle after tuning for SD6HC

[tze.yee.ng]

From: Tze Yee Ng <tze.yee.ng@altera.com>

On SD6HC the first command after tuning may be an R1b busy command (e.g.
the HS200->HS CMD6 during HS400 selection) that can time out on some eMMC
unless the PHY is given a brief settle after the final tap and DLL
re-lock.

Add a single 5 to 5.5 ms settle at the end of the SD6HC tuning path,
after the winning tap is applied, rather than on every set_tune_val()
call in the scan.

Signed-off-by: Tze Yee Ng <tze.yee.ng@altera.com>
---
Changes in v2:
- Moved the 5ms PHY settle out of the per-tap tuning loop to a single
  settle after the winning tap, on the success path only.
  (Adrian Hunter, Tanmay Kathpalia)
- Rewrote the comment to explain this specific call site.
  (Tanmay Kathpalia)
---
 drivers/mmc/host/sdhci-cadence-core.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/drivers/mmc/host/sdhci-cadence-core.c b/drivers/mmc/host/sdhci-cadence-core.c
index 745455743b01..c25b235ee909 100644
--- a/drivers/mmc/host/sdhci-cadence-core.c
+++ b/drivers/mmc/host/sdhci-cadence-core.c
@@ -7,6 +7,7 @@
 
 #include <linux/bitfield.h>
 #include <linux/bits.h>
+#include <linux/delay.h>
 #include <linux/dma-mapping.h>
 #include <linux/iopoll.h>
 #include <linux/module.h>
@@ -352,8 +353,11 @@ static int sdhci_cdns_execute_tuning(struct sdhci_host *host, u32 opcode)
 		return ret;
 
 	/* Block gap tuning is only required for SD4HC, not for SD6HC */
-	if (host->version >= SDHCI_SPEC_420)
+	if (host->version >= SDHCI_SPEC_420) {
+		/* Let the PHY settle after the final tap and DLL re-lock. */
+		usleep_range(5000, 5500);
 		return 0;
+	}
 
 	return sdhci_cdns_tune_blkgap(host->mmc);
 }
-- 
2.43.7

[PATCH v2 2/4] mmc: sdhci-cadence6: program PHONY_DQS_TIMING for extended-read DDR

[tze.yee.ng]

From: Tze Yee Ng <tze.yee.ng@altera.com>

The SD6HC PHY left PHONY_DQS_TIMING (phy_ctrl_reg[9:4]) at 0 in all
modes. Per the Cadence DLL PHY documentation it must be the rebar (RE#)
pulse width in clk_phy cycles minus 1 in extended read mode, and 0
otherwise. Leaving it 0 in extended-read DDR duplicates one DDR edge
(the silent odd/even edge-capture defect).

On this integration the rebar pulse is 2 clk_phy cycles, so extended-
read DDR needs 1; confirmed on DDR50 hardware (1 captures both beats, 2
corrupts reads). Derive it from the extended-read-mode state and apply
it only in DDR modes, since SDR extended-read samples a single edge and
is unaffected.

Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Tze Yee Ng <tze.yee.ng@altera.com>
---
Changes in v2:
- Added Adrian's Acked-by.
- Reworded the commit message to drop the "generic to any SD6HC-PHY SoC"
  framing. (Adrian Hunter)
---
 drivers/mmc/host/sdhci-cadence-phy-v6.c | 15 +++++++++++++++
 1 file changed, 15 insertions(+)

diff --git a/drivers/mmc/host/sdhci-cadence-phy-v6.c b/drivers/mmc/host/sdhci-cadence-phy-v6.c
index 22d56bb46d75..8d6a9c26c139 100644
--- a/drivers/mmc/host/sdhci-cadence-phy-v6.c
+++ b/drivers/mmc/host/sdhci-cadence-phy-v6.c
@@ -90,6 +90,9 @@
 #define SDHCI_CDNS6_PHY_CTRL_REG			0x2080
 #define   SDHCI_CDNS6_PHY_CTRL_PHONY_DQS_TIMING			GENMASK(9, 4)
 
+/* Width of this controller's rebar (RE#) pulse in clk_phy cycles. */
+#define SDHCI_CDNS6_PHY_REBAR_PULSE_CYCLES	2
+
 /* Default PHY settings */
 #define SDHCI_CDNS6_PHY_DEFAULT_IOCELL_DELAY		2500
 #define SDHCI_CDNS6_PHY_DEFAULT_DELAY_ELEMENT		24
@@ -143,6 +146,9 @@ struct sdhci_cdns6_phy {
 	bool cp_use_phony_dqs;		/* bit [20] */
 	bool cp_use_phony_dqs_cmd;	/* bit [19] */
 
+	/* PHY_CTRL register fields */
+	u32 cp_phony_dqs_timing;
+
 	/* HRS07 register - IO delay Information */
 	u8 sdhc_rw_compensate;		/* bits [20:16] */
 	u8 sdhc_idelay_val;		/* bits [4:0] */
@@ -517,6 +523,13 @@ static void sdhci_cdns6_phy_calc_dat_in(struct sdhci_cdns6_phy *phy)
 	if (phy->mode == MMC_TIMING_MMC_HS200)
 		phy->cp_read_dqs_delay = phy->hs200_tune_val;
 
+	if (phy->sdhc_extended_rd_mode &&
+	    (phy->mode == MMC_TIMING_UHS_DDR50 ||
+	     phy->mode == MMC_TIMING_MMC_DDR52))
+		phy->cp_phony_dqs_timing = SDHCI_CDNS6_PHY_REBAR_PULSE_CYCLES - 1;
+	else
+		phy->cp_phony_dqs_timing = 0;
+
 	if (strobe_dat) {
 		/* dqs loopback input via IO cell */
 		hcsdclkadj += phy->iocell_input_delay;
@@ -715,6 +728,8 @@ int sdhci_cdns6_phy_init(struct sdhci_cdns_priv *priv)
 
 	reg = sdhci_cdns6_read_phy_reg(priv, SDHCI_CDNS6_PHY_CTRL_REG);
 	reg &= ~SDHCI_CDNS6_PHY_CTRL_PHONY_DQS_TIMING;
+	reg |= FIELD_PREP(SDHCI_CDNS6_PHY_CTRL_PHONY_DQS_TIMING,
+			  phy->cp_phony_dqs_timing);
 	sdhci_cdns6_write_phy_reg(priv, SDHCI_CDNS6_PHY_CTRL_REG, reg);
 
 	/*
-- 
2.43.7

[PATCH v2 3/4] dt-bindings: mmc: cdns,sd6hc: add SD6HC DDR50 read-path tuning

[tze.yee.ng]

From: Tze Yee Ng <tze.yee.ng@altera.com>

DDR50 has no CMD19 tuning, so the SD6HC read path must be centred by
static, board/SoC-characterised PHY settings. Add three optional SD6HC
properties for the extended-read DDR modes (SD DDR50 and eMMC DDR52):

  - cdns,ddr-read-dqs-delay-ps: read-DQS delay in picoseconds that centres
    the read eye (default 0).
  - cdns,ddr-no-lpbk-dqs:       disable the loopback DQS read strobe and
    use the fabricated phony DQS instead. Loopback DQS is the recommended
    default; set this only on boards that need the phony DQS read path.
  - cdns,ddr-phony-dqs-timing:  PHY_CTRL[9:4] phony DQS assertion timing.
    The driver derives this from the RE# pulse width; this property
    overrides the computed value for boards whose flight time shifts the
    DDR data return.

Signed-off-by: Tze Yee Ng <tze.yee.ng@altera.com>
---
Changes in v2:
- Retitled to "dt-bindings: mmc: cdns,sd6hc:". (Tanmay Kathpalia)
- Renamed cdns,ddr50-* -> cdns,ddr-*. (Tanmay Kathpalia)
- cdns,ddr-read-dqs-delay-ps is now in picoseconds. (Krzysztof Kozlowski)
- Replaced the read-DQS source selector with a cdns,ddr-no-lpbk-dqs
  boolean. (Krzysztof Kozlowski)
- Reworded the phony-dqs-timing text. (Krzysztof Kozlowski, 
  Tanmay Kathpalia)
- Dropped the SD4HC note. (Tanmay Kathpalia)
- Scope the new properties to the extended-read DDR modes (DDR50 and
  DDR52). (Tanmay Kathpalia)
---
 .../devicetree/bindings/mmc/cdns,sd6hc.yaml   | 30 +++++++++++++++++++
 1 file changed, 30 insertions(+)

diff --git a/Documentation/devicetree/bindings/mmc/cdns,sd6hc.yaml b/Documentation/devicetree/bindings/mmc/cdns,sd6hc.yaml
index d5ea2717904b..911ce58f8dab 100644
--- a/Documentation/devicetree/bindings/mmc/cdns,sd6hc.yaml
+++ b/Documentation/devicetree/bindings/mmc/cdns,sd6hc.yaml
@@ -74,6 +74,36 @@ properties:
     maximum: 1000
     default: 24
 
+  cdns,ddr-read-dqs-delay-ps:
+    description: >
+      Read-DQS delay (DLL_SLAVE[7:0]) in picoseconds that centres the read
+      eye in the extended-read DDR modes (SD DDR50, eMMC DDR52), which have
+      no CMD19 tuning. The PHY runs the DLL bypassed in these modes, so the
+      driver converts this to delay elements (divided by
+      cdns,delay-element-ps). The 8-bit field holds at most 255 elements;
+      larger values are clamped to that limit.
+    minimum: 0
+    default: 0
+
+  cdns,ddr-no-lpbk-dqs:
+    description: >
+      Disable the loopback DQS read strobe and use the fabricated (phony)
+      DQS instead in the extended-read DDR modes (SD DDR50, eMMC DDR52).
+      Loopback DQS is the recommended default; set this only on boards that
+      require the phony DQS read path.
+    type: boolean
+
+  cdns,ddr-phony-dqs-timing:
+    description: >
+      Phony DQS assertion timing (PHY_CTRL[9:4]) for the extended-read DDR
+      modes (SD DDR50, eMMC DDR52). The driver computes this from the RE#
+      pulse width per the Cadence PHY guide; set it only to override that
+      value on boards whose DDR data returns shifted (e.g. longer flight
+      time on modular/SoM layouts). If absent, the computed value is used.
+    $ref: /schemas/types.yaml#/definitions/uint32
+    minimum: 0
+    maximum: 0x3f
+
 required:
   - compatible
   - reg
-- 
2.43.7

Re: [PATCH v2 3/4] dt-bindings: mmc: cdns,sd6hc: add SD6HC DDR50 read-path tuning

[Krzysztof Kozlowski]

On Fri, Oct 09, 2026 at 10:14:50AM +0800, tze.yee.ng@altera.com wrote:
> From: Tze Yee Ng <tze.yee.ng@altera.com>
> 
> DDR50 has no CMD19 tuning, so the SD6HC read path must be centred by
> static, board/SoC-characterised PHY settings. Add three optional SD6HC
> properties for the extended-read DDR modes (SD DDR50 and eMMC DDR52):
> 
>   - cdns,ddr-read-dqs-delay-ps: read-DQS delay in picoseconds that centres
>     the read eye (default 0).
>   - cdns,ddr-no-lpbk-dqs:       disable the loopback DQS read strobe and
>     use the fabricated phony DQS instead. Loopback DQS is the recommended
>     default; set this only on boards that need the phony DQS read path.
>   - cdns,ddr-phony-dqs-timing:  PHY_CTRL[9:4] phony DQS assertion timing.
>     The driver derives this from the RE# pulse width; this property
>     overrides the computed value for boards whose flight time shifts the
>     DDR data return.
> 
> Signed-off-by: Tze Yee Ng <tze.yee.ng@altera.com>
> ---
> Changes in v2:
> - Retitled to "dt-bindings: mmc: cdns,sd6hc:". (Tanmay Kathpalia)
> - Renamed cdns,ddr50-* -> cdns,ddr-*. (Tanmay Kathpalia)
> - cdns,ddr-read-dqs-delay-ps is now in picoseconds. (Krzysztof Kozlowski)
> - Replaced the read-DQS source selector with a cdns,ddr-no-lpbk-dqs
>   boolean. (Krzysztof Kozlowski)
> - Reworded the phony-dqs-timing text. (Krzysztof Kozlowski, 
>   Tanmay Kathpalia)
> - Dropped the SD4HC note. (Tanmay Kathpalia)
> - Scope the new properties to the extended-read DDR modes (DDR50 and
>   DDR52). (Tanmay Kathpalia)

There are no lore links in the cover letter to previous versions and b4
diff fails.

b4 diff 'cover.1791459448.git.tze.yee.ng@altera.com'
Looking up cover.1791459448.git.tze.yee.ng@altera.com
Checking for older revisions
Grabbing search results from lore.kernel.org
---
Analyzing 5 messages in the thread
Could not find lower series to compare against.

Why aren't you using b4 to send patches? Why making it difficult for us?

> ---
>  .../devicetree/bindings/mmc/cdns,sd6hc.yaml   | 30 +++++++++++++++++++
>  1 file changed, 30 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/mmc/cdns,sd6hc.yaml b/Documentation/devicetree/bindings/mmc/cdns,sd6hc.yaml
> index d5ea2717904b..911ce58f8dab 100644
> --- a/Documentation/devicetree/bindings/mmc/cdns,sd6hc.yaml
> +++ b/Documentation/devicetree/bindings/mmc/cdns,sd6hc.yaml
> @@ -74,6 +74,36 @@ properties:
>      maximum: 1000
>      default: 24
>  
> +  cdns,ddr-read-dqs-delay-ps:
> +    description: >
> +      Read-DQS delay (DLL_SLAVE[7:0]) in picoseconds that centres the read
> +      eye in the extended-read DDR modes (SD DDR50, eMMC DDR52), which have
> +      no CMD19 tuning. The PHY runs the DLL bypassed in these modes, so the
> +      driver converts this to delay elements (divided by
> +      cdns,delay-element-ps). The 8-bit field holds at most 255 elements;
> +      larger values are clamped to that limit.
> +    minimum: 0

Drop, 0 is the default.

Where is the maximum value?

> +    default: 0
> +
> +  cdns,ddr-no-lpbk-dqs:
> +    description: >

Drop > everywhere

Best regards,
Krzysztof

[PATCH v2 4/4] mmc: sdhci-cadence6: read SD6HC DDR50 tuning from device tree

[tze.yee.ng]

From: Tze Yee Ng <tze.yee.ng@altera.com>

DDR50 has no CMD19 tuning, so the SD6HC read path relies on static PHY
settings that need board/SoC characterisation. Read the read-DQS delay,
read-DQS source and phony DQS assertion timing from the new
cdns,ddr-read-dqs-delay-ps, cdns,ddr-no-lpbk-dqs and
cdns,ddr-phony-dqs-timing DT properties at PHY probe and apply them in
the extended-read DDR modes (DDR50 and DDR52). The read-DQS delay is
given in picoseconds and converted to delay elements with
cdns,delay-element-ps; since that quotient depends on the element size,
it is clamped to the 8-bit PHY field maximum (255) to avoid wrap-around.

Loopback DQS is the recommended read-capture path and stays the default;
cdns,ddr-no-lpbk-dqs lets a board fall back to the fabricated phony DQS.
When a property is absent the driver-computed value is kept - for the
phony DQS timing, the value derived from the RE# pulse width
(REBAR_PULSE_CYCLES-1).

Signed-off-by: Tze Yee Ng <tze.yee.ng@altera.com>
---
Changes in v2:
- Updated patch title to "mmc: sdhci-cadence6:" since it touches only the
  v6 PHY.
- Renamed the properties to cdns,ddr-*.
- Read cdns,ddr-read-dqs-delay-ps in ps and convert it to delay elements 
  (dividing by cdns,delay-element-ps), clamping that quotient to the 8-bit
  PHY field. (Krzysztof Kozlowski)
- Read cdns,ddr-no-lpbk-dqs via of_property_read_bool(). (Krzysztof Kozlowski)
- Dropped the v1 per-property range checks and redundant FIELD_MAX() write
  masks. (Adrian Hunter)
- Apply the overrides in both DDR50 and DDR52.
---
 drivers/mmc/host/sdhci-cadence-phy-v6.c | 59 ++++++++++++++++++++++++-
 1 file changed, 58 insertions(+), 1 deletion(-)

diff --git a/drivers/mmc/host/sdhci-cadence-phy-v6.c b/drivers/mmc/host/sdhci-cadence-phy-v6.c
index 8d6a9c26c139..2b1b7256731a 100644
--- a/drivers/mmc/host/sdhci-cadence-phy-v6.c
+++ b/drivers/mmc/host/sdhci-cadence-phy-v6.c
@@ -129,6 +129,11 @@ struct sdhci_cdns6_phy {
 	/* Active delay element (ps); doubled when one SDMCLK requires > 256 steps */
 	u32 delay_element;
 
+	/* DDR read-path overrides (SoC-specific) */
+	u32 ddr_read_dqs_delay_ps;
+	bool ddr_no_lpbk_dqs;
+	s32 ddr_phony_dqs_timing;
+
 	/* PHY_DLL_SLAVE_CTRL register fields */
 	u8 cp_read_dqs_cmd_delay;	/* bits [31:24] */
 	u8 cp_clk_wrdqs_delay;		/* bits [23:16] */
@@ -145,6 +150,7 @@ struct sdhci_cdns6_phy {
 	/* PHY_DQS_TIMING register fields */
 	bool cp_use_phony_dqs;		/* bit [20] */
 	bool cp_use_phony_dqs_cmd;	/* bit [19] */
+	bool cp_use_lpbk_dqs;		/* bit [21] */
 
 	/* PHY_CTRL register fields */
 	u32 cp_phony_dqs_timing;
@@ -523,6 +529,16 @@ static void sdhci_cdns6_phy_calc_dat_in(struct sdhci_cdns6_phy *phy)
 	if (phy->mode == MMC_TIMING_MMC_HS200)
 		phy->cp_read_dqs_delay = phy->hs200_tune_val;
 
+	if ((phy->mode == MMC_TIMING_UHS_DDR50 ||
+	     phy->mode == MMC_TIMING_MMC_DDR52) && phy->ddr_read_dqs_delay_ps) {
+		u32 steps = phy->ddr_read_dqs_delay_ps / phy->delay_element_org;
+		u32 max_steps = FIELD_MAX(SDHCI_CDNS6_PHY_DLL_SLAVE_CTRL_READ_DQS_DELAY);
+
+		phy->cp_read_dqs_delay = min_t(u32, steps, max_steps);
+	}
+
+	phy->cp_use_lpbk_dqs = 1;
+
 	if (phy->sdhc_extended_rd_mode &&
 	    (phy->mode == MMC_TIMING_UHS_DDR50 ||
 	     phy->mode == MMC_TIMING_MMC_DDR52))
@@ -530,6 +546,23 @@ static void sdhci_cdns6_phy_calc_dat_in(struct sdhci_cdns6_phy *phy)
 	else
 		phy->cp_phony_dqs_timing = 0;
 
+	/*
+	 * Loopback DQS is the recommended read-capture path; allow boards that
+	 * need the fabricated phony DQS instead to opt out in the DDR modes.
+	 */
+	if ((phy->mode == MMC_TIMING_UHS_DDR50 ||
+	     phy->mode == MMC_TIMING_MMC_DDR52) && phy->ddr_no_lpbk_dqs)
+		phy->cp_use_lpbk_dqs = 0;
+
+	/*
+	 * The computed phony DQS timing above is derived from the RE# pulse
+	 * width. Allow a DT override for boards whose flight time shifts the
+	 * returning DDR data relative to the fabricated strobe.
+	 */
+	if ((phy->mode == MMC_TIMING_UHS_DDR50 ||
+	     phy->mode == MMC_TIMING_MMC_DDR52) && phy->ddr_phony_dqs_timing >= 0)
+		phy->cp_phony_dqs_timing = phy->ddr_phony_dqs_timing;
+
 	if (strobe_dat) {
 		/* dqs loopback input via IO cell */
 		hcsdclkadj += phy->iocell_input_delay;
@@ -693,10 +726,11 @@ int sdhci_cdns6_phy_init(struct sdhci_cdns_priv *priv)
 	sdhci_cdns6_dll_reset(priv, true);
 
 	reg = sdhci_cdns6_read_phy_reg(priv, SDHCI_CDNS6_PHY_DQS_TIMING_REG);
+	reg &= ~SDHCI_CDNS6_PHY_DQS_TIMING_USE_LPBK_DQS;
 	reg &= ~SDHCI_CDNS6_PHY_DQS_TIMING_USE_PHONY_DQS;
 	reg &= ~SDHCI_CDNS6_PHY_DQS_TIMING_USE_PHONY_DQS_CMD;
 	reg |= SDHCI_CDNS6_PHY_DQS_TIMING_USE_EXT_LPBK_DQS;
-	reg |= SDHCI_CDNS6_PHY_DQS_TIMING_USE_LPBK_DQS;
+	reg |= FIELD_PREP(SDHCI_CDNS6_PHY_DQS_TIMING_USE_LPBK_DQS, phy->cp_use_lpbk_dqs);
 	reg |= FIELD_PREP(SDHCI_CDNS6_PHY_DQS_TIMING_USE_PHONY_DQS, phy->cp_use_phony_dqs);
 	reg |= FIELD_PREP(SDHCI_CDNS6_PHY_DQS_TIMING_USE_PHONY_DQS_CMD, phy->cp_use_phony_dqs_cmd);
 	sdhci_cdns6_write_phy_reg(priv, SDHCI_CDNS6_PHY_DQS_TIMING_REG, reg);
@@ -878,6 +912,7 @@ int sdhci_cdns6_phy_probe(struct platform_device *pdev, struct sdhci_cdns_priv *
 	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
 	struct sdhci_cdns6_phy *phy;
 	unsigned long val;
+	u32 prop;
 	int ret;
 
 	phy = devm_kzalloc(dev, sizeof(*phy), GFP_KERNEL);
@@ -916,6 +951,28 @@ int sdhci_cdns6_phy_probe(struct platform_device *pdev, struct sdhci_cdns_priv *
 
 	phy->delay_element_org = phy->delay_element;
 
+	/*
+	 * Optional read-path tuning for the extended-read DDR modes (SD DDR50,
+	 * eMMC DDR52).
+	 */
+	phy->ddr_read_dqs_delay_ps = 0;
+	of_property_read_u32(dev->of_node, "cdns,ddr-read-dqs-delay-ps",
+			     &phy->ddr_read_dqs_delay_ps);
+	if (phy->ddr_read_dqs_delay_ps / phy->delay_element_org >
+	    FIELD_MAX(SDHCI_CDNS6_PHY_DLL_SLAVE_CTRL_READ_DQS_DELAY))
+		dev_warn(dev,
+			 "cdns,ddr-read-dqs-delay-ps %u too large, clamping to %lu elements\n",
+			 phy->ddr_read_dqs_delay_ps,
+			 (unsigned long)FIELD_MAX(SDHCI_CDNS6_PHY_DLL_SLAVE_CTRL_READ_DQS_DELAY));
+
+	phy->ddr_no_lpbk_dqs = of_property_read_bool(dev->of_node,
+						     "cdns,ddr-no-lpbk-dqs");
+
+	phy->ddr_phony_dqs_timing = -1;
+	if (!of_property_read_u32(dev->of_node, "cdns,ddr-phony-dqs-timing",
+				  &prop))
+		phy->ddr_phony_dqs_timing = prop;
+
 	priv->phy = phy;
 
 	return 0;
-- 
2.43.7