* [U-Boot-Users] Porting custom board from u-boot 1.0.1 to u-boot 1.1.2
@ 2005-03-14 15:47 Armand Ciejak
2005-03-14 17:03 ` [U-Boot-Users] smc91111 and MII richard at uclinux.net
2005-03-14 20:17 ` [U-Boot-Users] Porting custom board from u-boot 1.0.1 to u-boot 1.1.2 Wolfgang Denk
0 siblings, 2 replies; 5+ messages in thread
From: Armand Ciejak @ 2005-03-14 15:47 UTC (permalink / raw)
To: u-boot
I'm working on the Metrowerks "QUICCstart 8540 Evaluation System" which
is provided with u-boot 1.0.1 (custom board configuration called EVAL8540).
I have got the source code from the installation CD and want to port it
to the latest u-boot version.
To do that I would like to know the changes which occured between this
two version of the u-boot project and what do I have to adapt in the
source code of the EVAL8540 configuration.
PS: I already installed the ELDK 3.1 on my Linux PC.
Best regards and thanks in advance,
Armand
^ permalink raw reply [flat|nested] 5+ messages in thread
* [U-Boot-Users] smc91111 and MII
2005-03-14 15:47 [U-Boot-Users] Porting custom board from u-boot 1.0.1 to u-boot 1.1.2 Armand Ciejak
@ 2005-03-14 17:03 ` richard at uclinux.net
2005-03-14 20:17 ` [U-Boot-Users] Porting custom board from u-boot 1.0.1 to u-boot 1.1.2 Wolfgang Denk
1 sibling, 0 replies; 5+ messages in thread
From: richard at uclinux.net @ 2005-03-14 17:03 UTC (permalink / raw)
To: u-boot
Evening (o;
Is this a generic behaviour among all ethernet drivers that
it get's reset every time before it is used like the smc91111?
So we just block ourself out to use the MII commands
although functions are in the driver ready to be used
(with some slight modifications ;o).
best regards
rick
^ permalink raw reply [flat|nested] 5+ messages in thread
* [U-Boot-Users] Porting custom board from u-boot 1.0.1 to u-boot 1.1.2
2005-03-14 15:47 [U-Boot-Users] Porting custom board from u-boot 1.0.1 to u-boot 1.1.2 Armand Ciejak
2005-03-14 17:03 ` [U-Boot-Users] smc91111 and MII richard at uclinux.net
@ 2005-03-14 20:17 ` Wolfgang Denk
2005-03-21 10:40 ` [U-Boot-Users] " Armand Ciejak
1 sibling, 1 reply; 5+ messages in thread
From: Wolfgang Denk @ 2005-03-14 20:17 UTC (permalink / raw)
To: u-boot
In message <d14bes$o3a$1@sea.gmane.org> you wrote:
> I'm working on the Metrowerks "QUICCstart 8540 Evaluation System" which
Please bear with my ignorance, but is this different from the
MPC8540ADS board?
> To do that I would like to know the changes which occured between this
> two version of the u-boot project and what do I have to adapt in the
Identify which specific version the port was based on, and then use
"cvs diff". You may also want to run "cvsps" to break the changes
down into patchsets. See also the CHANGELOG file for documentation
about changes.
Best regards,
Wolfgang Denk
--
Software Engineering: Embedded and Realtime Systems, Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
People are always a lot more complicated than you think. It's very
important to remember that. - Terry Pratchett, _Truckers_
^ permalink raw reply [flat|nested] 5+ messages in thread
* [U-Boot-Users] Re: Porting custom board from u-boot 1.0.1 to u-boot 1.1.2
2005-03-14 20:17 ` [U-Boot-Users] Porting custom board from u-boot 1.0.1 to u-boot 1.1.2 Wolfgang Denk
@ 2005-03-21 10:40 ` Armand Ciejak
2005-03-21 11:04 ` Wolfgang Denk
0 siblings, 1 reply; 5+ messages in thread
From: Armand Ciejak @ 2005-03-21 10:40 UTC (permalink / raw)
To: u-boot
Wolfgang Denk wrote:
> In message <d14bes$o3a$1@sea.gmane.org> you wrote:
>> I'm working on the Metrowerks "QUICCstart 8540 Evaluation System" which
>
> Please bear with my ignorance, but is this different from the
> MPC8540ADS board?
The main difference I noticed in the hardware parts are:
MPC8540ADS Metrowerks boards
Flash
32bit 16bit
16MB 8MB
? Intel 28F640J3
SDRAM
64 MB no SDRAM
DDR
128 MB 256 MB
>
>> To do that I would like to know the changes which occured between this
>> two version of the u-boot project and what do I have to adapt in the
>
> Identify which specific version the port was based on, and then use
> "cvs diff". You may also want to run "cvsps" to break the changes
> down into patchsets. See also the CHANGELOG file for documentation
> about changes.
>
> Best regards,
>
> Wolfgang Denk
>
^ permalink raw reply [flat|nested] 5+ messages in thread* [U-Boot-Users] Re: Porting custom board from u-boot 1.0.1 to u-boot 1.1.2
2005-03-21 10:40 ` [U-Boot-Users] " Armand Ciejak
@ 2005-03-21 11:04 ` Wolfgang Denk
0 siblings, 0 replies; 5+ messages in thread
From: Wolfgang Denk @ 2005-03-21 11:04 UTC (permalink / raw)
To: u-boot
In message <d1m84h$clm$1@sea.gmane.org> you wrote:
>
> > Please bear with my ignorance, but is this different from the
> > MPC8540ADS board?
>
> The main difference I noticed in the hardware parts are:
I see. Consider it a new port, then.
Best regards,
Wolfgang Denk
--
Software Engineering: Embedded and Realtime Systems, Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
For every complex problem, there is a solution that is simple, neat,
and wrong. -- H. L. Mencken
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2005-03-21 11:04 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2005-03-14 15:47 [U-Boot-Users] Porting custom board from u-boot 1.0.1 to u-boot 1.1.2 Armand Ciejak
2005-03-14 17:03 ` [U-Boot-Users] smc91111 and MII richard at uclinux.net
2005-03-14 20:17 ` [U-Boot-Users] Porting custom board from u-boot 1.0.1 to u-boot 1.1.2 Wolfgang Denk
2005-03-21 10:40 ` [U-Boot-Users] " Armand Ciejak
2005-03-21 11:04 ` Wolfgang Denk
This is an external index of several public inboxes,
see mirroring instructions on how to clone and mirror
all data and code used by this external index.